Search Results

Search found 9373 results on 375 pages for 'wireless mouse'.

Page 112/375 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• How do I install the EW-7318Ug wireless drivers?

  - by user69731

  I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

  Read the article

• How to Disable Touchpad tap in Toshiba Tecra R850 in Oneiric - it is recognized as a PS/2 mouse

  - by Kibi

  I know there's a lot of similar questions, but nothing I have tried here works yet - perhaps I was doing it wrong. New Laptop - Toshiba Tecra R850 with an install of Oneiric 64 bit. Mostly things are working well, but I have a problem with the touchpad (or whatever it's called) - whenever I use it for moving the mouse pointer I accidentally tap on it - basically I am clicking all over the place by accident. So I want to disable the tap-as-click (after all, I have buttons for clicks too). I open up "Mouse and Touchpad" and on the Touchpad tab I check "Disable touchpad when typing" and UNcheck "Enable mouse clicks with touchpad". This does not achieve anything. Ditto Synaptiks and other similar tools. EDIT OK it turns out that this is a somewhat known problem - it seems the touchpad is not being recognized as a touchpad, it is seen as a PS/2 mouse. So any adjustments made with various settings programs to the "touchpad" don't affect it. I've been looking at solutions for getting the touchpad correctly recognized and not achieved it yet - seems there is a problem at the kernel level...I tried (foolishly) a suggestion to replace the psmouse.ko driver ...this screwed some stuff up and didn't solve my problem. So - anyone know an answer? Thanks Kibi

  Read the article

• converting 2D mouse coordinates to 3D space in OpenGL ES

  - by Jayesh

  I want to convert mouse's current X and Y coordinates into the 3D space I have drawn in the viewport. I need to do this on the OpenGL ES platform. I found following possible solutions implemented in OpenGL, but none fits what I am looking for. I found NeHe's tutorial on doing exactly this, but in traditional OpenGL way. It uses gluUnProject. http://nehe.gamedev.net/data/articles/article.asp?article=13 Although gluUnProject is not available in OpenGL ES, its implementation seems simple enough to port back. But before calling it, we need to call glReadPixels with GL_DEPTH_COMPONENT and that is not possible in OpenGL ES. (The reason I found in this thread: http://www.khronos.org/message_boards/viewtopic.php?f=4&t=771) What I want to do is similar to picking, except that I don't want to select the object but I want exact coordinates so that I can recognize particular portion of the object that is currently under mouse cursor. I went through the Picking tutorials in this answer. http://stackoverflow.com/posts/2211312/revisions But they need glRenderMode, which I believe is absent in OpenGL ES. If you know how to solve this problem in OpenGL ES, please let me know. Thanks.

  Read the article

• Flex HTMLLoader component not raising mouseDown events for all mouse clicks

  - by shane

  I have built a Air 2/Flex 4 kiosk application with Flash Builder 4. Currently I am implementing a touch screen browser to enable users to navigate company training videos. In an attempt to improve the usability of the website on the touchscreen I have placed the HTML component in an adaption of Doug McCune's DragScrollingCanvas (updated to use the flex 4 'Scroller' component) to allow users to scroll the webpage by dragging their finger across the screen. The mouseDown event is used to start scrolling the viewport. In addition the webpage was modified to disable text selection with the following css: html { -webkit-user-select: none; cursor: default; } The problem I face is that the HTMLLoader component only fires a mouseDown if a link/input/button on the webpage is clicked, not when the background or any text is clicked. In addition if I remove the custom css the mouseDown event will not fire when text is being selected, but will if previously highlighted text is clicked. As an alternative I also tried adding a group container with the same dimensions as the HTMLLoader to detect the mouseDown events (so that the group container and HTMLLoader have the same Dragable parent container) and was able to capture mouseDown events and scroll the viewport as expected. However as the mouse event is handled by the group container, I am now unable to navigate the webpage. Does anybody know why the HTMLLoader component is not raising mouseDown events for all mouse clicks?

  Read the article

• Capturing mouse events for specific dom/web elements in QT

  - by Red Serpent

  Hi I would like to know if it is possible in QTWebKit to install an event filter or capture events that occur from specific Dom elements. For example, my webview is showing a webpage that has text, images and an edit box, I want to disable the right-clicking and highlighting functionality on the text and images but at the same time when the user right-clicks inside the edit box, I want to display my context menu. I am not sure where should I install my event filter, in QwebView or QwebPage... currently this is what I'm using: MainWindow::MainWindow() { centralWidget = new WebView(this); setCentralWidget(centralWidget); centralWidget->webView->installEventFilter(this); //No mouse events are rising on QWebPage //centralWidget->webView->page()->installEventFilter(this); } As its clear in the code above, when installing an EventFilter on QwebPage, I never receive any QMouseEvents, not by moving clicking or releasing any mouse buttons. While when setting it to filter events from QWebView it works fine. I am really interested with the first part of my question as to how handle Dom elements differently. How can I achieve such goal? Regards

  Read the article

• Envoking mouse capturing function onmousedown?

  - by Babiker

  I have the following: <html> <script type="text/javascript"> document.onmousemove = getCursorXY; function getCursorXY(e) { document.getElementById('cursorX').value = (window.Event) ? e.pageX : event.clientX + (document.documentElement.scrollLeft ? document.documentElement.scrollLeft : document.body.scrollLeft); document.getElementById('cursorY').value = (window.Event) ? e.pageY : event.clientY + (document.documentElement.scrollTop ? document.documentElement.scrollTop : document.body.scrollTop); } </script> <body> <input id="cursorX" size="3"> <input id="cursorY" size="3"> <input type="button" id="button"> </body> </html> With this my mouse coordinates are displayed in the input fields when the page loads and whenever i move the mouse. How can i make this work only when i mousedown over #button and then stop at the last coordinates when i mouseup only over #button? using firefox 3.6.3 Thanks in advance :)

  Read the article

• removing mouse events/controls from swing components with glasspane

  - by Deger

  Hi all, I have a client-server application and i am using swing in the client side. My swing client has one main window (jframe) and lots of panels, toolbars and menubar in it. I want to remove all client action/mouse events (or simply grab and do nothing) while client is waiting response from server by means of glasssPane. Here is the code i wrote: private final static MouseAdapter mouseAdapter = new MouseAdapter() { public void mouseClicked(MouseEvent e) { System.out.println("MouseClicked..!"); } }; private static Cursor WAIT_CURSOR = Cursor.getPredefinedCursor(Cursor.WAIT_CURSOR); private static Cursor DEFAULT_CURSOR = Cursor.getPredefinedCursor(Cursor.DEFAULT_CURSOR); and public static void startWaitCursor(JComponent comp) { MainWindow root = ((MainWindow) comp.getTopLevelAncestor()); root.getGlassPane().setCursor(WAIT_CURSOR); root.getGlassPane().addMouseListener(mouseAdapter); root.getGlassPane().setVisible(true); } public static void stopWaitCursor(JComponent comp) { MainWindow root = ((MainWindow) comp.getTopLevelAncestor()); root.getGlassPane().setCursor(DEFAULT_CURSOR); root.getGlassPane().setVisible(false); } but i am not able to manage the grab mouse events. Changing cursors at the glassPane is working fine but either i am not able to add mouseAdapter or am not able to make glasssPane become to the top level component. Any idea? Thanks.

  Read the article

• JTable listener problem

  - by newbie123

  I added a mouse clicked listner to my jtable, when i double click the row, will pop up an window accordingly. jTable.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent e) { double amount = Double.parseDouble(jTable.getValueAt(getSelectedRow(), 4).toString()); String remarks = jTable.getValueAt(getSelectedRow(), 3).toString(); String transactionID = jTable.getValueAt(getSelectedRow(), 1).toString(); new EditFrame(...) } }); This code I used to retrieve the row selected row. public int getSelectedRow() { jTable.getSelectionModel().addListSelectionListener( new ListSelectionListener() { public void valueChanged(ListSelectionEvent event) { int viewRow = jTable.getSelectedRow(); selectedRow = viewRow; System.out.println(viewRow); } }); return selectedRow; } In my case, I realised when I clicked the second row in the first time, I get null for selectedRow, only when I select first row then second row, I then can get the correct data. And If I removed the mouse listener the problem then be solved. Is it because I doing something wrong at the mouse click listener?

  Read the article

• MacBook Pro with Time Capsule can not see Samsung CLX 3175FW wireless printer on Bonjour

  - by syncopat

  I have a MacBook Pro running OS X 10.6 and another MacBook Pro running OS X 10.5. Neither see my Samsung printer when I click on Bonjour. Needless to say neither will print. I have a Time Capsule connected wirelessly to my MacBook Pros. I have tried reinstalling drivers for the printer but nothing seems to work. I tried this approach because when Apple replaced my Time Capsule and I went to print the way I had initially been running printing requests would get hung up. Any suggestions would be helpful?

  Read the article

• Wireless AAA for a small, bandwidth-limited hotel.

  - by Anthony Hiscox

  We (the tech I work with and myself) live in a remote northern town where Internet access is somewhat of a luxury, and bandwidth is quite limited. Here, overage charges ranging from few hundreds, to few thousands of dollars a month, is not uncommon. I myself incur regular monthly charges just through my regular Internet usage at home (I am allowed 10G for $60CAD!) As part of my work, I have found myself involved with several hotels that are feeling this. I know that I can come up with something to solve this problem, but I am relatively new to system administration and I don't want my dreams to overcome reality. So, I pass these ideas on to you, those with much more experience than I, in hopes you will share some of your thoughts and concerns. This system must be cost effective, yes the charges are high here, but the trust in technology is the lowest I've ever seen. Must be capable of helping client reduce their usage (squid) Allow a limited (throughput and total usage) amount of free Internet, as this is often franchise policy. Allow a user to track their bandwidth usage Allow (optional) higher speed and/or usage for an additional charge. This fee can be obtained at the front desk on checkout and should not require the use of PayPal or Credit Card. Unfortunately some franchises have ridiculous policies that require the use of a third party remote service to authenticate guests to your network. This means WPA is out, and it also means that I do not auth before Internet usage, that will be their job. However, I do require the ABILITY to perform authentication for Internet access if a hotel does not have this policy. I will still have to track bandwidth (under a guest account by default) and provide the same limiting, however the guest often will require a complete 'unlimited' access, in terms of existence, not throughput. Provide firewalling capabilities for hotels that have nothing, Office, and Guest network segregation (some of these guys are running their office on the guest network, with no encryption, and a simple TOS to get on!) Prevent guests from connecting to other guests, however provide a means to allow this to happen. IE. Each guest connects to a page and allows the other guest, this writes a iptables rule (with python-netfilter) and allows two rooms to play a game, for instance. My thoughts on how to implement this. One decent box (we'll call it a router now) with a lot of ram, and 3 NIC's: Internet Office Guests (AP's + In Room Ethernet) Router Firewall Rules Guest can talk to router only, through which they are routed to where they need to go, including Internet services. Office can be used to bridge Office to Internet if an existing solution is not in place, otherwise, it simply works for a network accessible web (webmin+python-webmin?) interface. Router Software: OpenVZ provides virtualization for a few services I don't really trust. Squid, FreeRADIUS and Apache. The only service directly accessible to guests is Apache. Apache has mod_wsgi and django, because I can write quickly using django and my needs are low. It also potentially has the FreeRADIUS mod, but there seems to be some caveats with this. Firewall rules are handled on the router with iptables. Webmin (or a custom django app maybe) provides abstracted control over any features that the staff may need to access. Python, if you haven't guessed it's the language I feel most comfortable in, and I use it for almost everything. And finally, has this been done, is it a overly massive project not worth taking on for one guy, and/or is there some tools I'm missing that could be making my life easier? For the record, I am fairly good with Python, but not very familiar with many other languages (I can struggle through PHP, it's a cosmetic issue there). I am also an avid linux user, and comfortable with config files and command line. Thank you for your time, I look forward to reading your responses. Edit: My apologies if this is not a Q&A in the sense that some were expecting, I'm just looking for ideas and to make sure I'm not trying to do something that's been done. I'm looking at pfSense now as a possible start for what I need.

  Read the article

• Eclipse making background video skip with almost every click of the mouse

  - by RustyH

  The problem is i like to listen to videos online (mostly or all flash video) while programming and never had any problems until i started using eclipse, now every time i do just about anything other than type, it makes the video skip/freeze really bad and is really annoying. I have never had this happen using visual studio, netbeans, or adobe flash for that matter, unless i was compiling or doing something that hogs the processor. Are there any settings that might could fix this its getting really annoying. it happens almost every time i even click "find" on the find pop-up window and it is not like it is having to search a big file or anything it is only 700 lines, with honestly only about 1/2 that have content on them. Any ideas?

  Read the article

• Mouse to touch point driver, Emulate touch points with mice

  - by ydfeed

  Are there any drivers to convert mice to touch points for multi-touch applications on Windows 7?

  Read the article

• Touchpad mouse problem

  - by megatr0n

  Hi all. I have a toshiba satellite and its been behaving weirdly. It only works at the password prompt screen to logon but as soon as I am logged in, it just stops working. Left nor right button clicks are working. I am running vista home. Any pointers on how to go about this? Thanks.

  Read the article

• Copy and Paste without needing to use the Mouse

  - by Paul Farry

  In previous versions of windows when your were Copying Files (Ctrl-C) then alt-Tab (to the appropriate window) and Pasting (Ctrl-V) using the Keyboard everything could be driven by the keyboard. With Vista and 7, it seems if you are copying and pasting (and the files exist) in the Destination Location you have to Click the Copy and Replace, there doesn't seem to be a way to do it... "Do this for the next {n} Conflicts" can be driven by Alt-D, but the "Copy and Replace" and "Don't Copy" are not. Or is there and have I just missed something? I'm more than happy to change registry or something to enable Keyboard shortcuts for this.

  Read the article

• DNS Settings in Cisco Wireless Lan Controllers

  - by Braden

  The WLC is a 2100 series and I have looked back and forth through the entire web interface. Originally the idea was that the gateway should be the DNS controler and the WLC pointed directly at the gateway. For some reason, random clients are having DNS specific issues when it comes to seeing certain shares around the network. The problems are also very intermittent. Aside from going to each box and implementing a static DNS is there ACTUALLY a DNS setting lodged into the WLC settings (and I am being a numpty and can't find them) or am I stuck with performing the config 1 by 1?

  Read the article

• SOHO NETGEAR wireless router disconnects when downloading torrents

  - by Lirik

  I have a NETGEAR WGT624 router at home which dies when there is a heavy torrent load. I open up my torrent client and it downloads for about 5 to 10 minutes and it continues to increase the number of seeds (goes up to 70-80 seeds), but after that the router simply fails and I have to restart it in order to get an internet connection again. Is there any way that I can fix this? New router firmware? Change some router options? Feed it a cookie? Anything?

  Read the article

• Rate limit a wireless interface

  - by Jamie Hankins

  I have access to my routers SSH and IPTables. I want to rate limit my guest network to 1Mb/s so they can't guzzle my bandwidth. rai1 RTWIFI SoftAP ESSID:"GuestNetwork" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi0 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F8 Bit Rate=300 Mb/s wdsi1 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi2 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s wdsi3 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s I'm just wondering the command I need to limit it. I tried the iwconfig limit command but it failed. Thanks

  Read the article

• Simple way to make wired internet wireless without router

  - by Anriëtte Combrink

  Hi there Is there any device which you can plug into an Ethernet port and then have it broadcast the internet connection it receives through Ethernet wirelessly with a set password (maybe a serial number on device itself)? The problem is, I have a Wi-fi capable device, an iPhone and I want to use the wired internet connection in a hotel room, but the iPhone needs a Wi-fi signal. How can I accomplish this with a rather simplistic device. // EDIT: Can this be achieved with an Apple Airport Express?

  Read the article

• Wireless Password

  - by Campo

  I have a security policy question: I want to know how other admins handle the WIFI password in the office. Does everyone know it? Do you enter it in for the user or guest every time and keep it a secret. I am in camp 2. Just want to know what others do and their reasoning behind it.

  Read the article

• HP Pavilion DV6 doesn't recognize wireless networks

  - by Mike N.

  Okay so about a few weeks after I got my laptop the wifi would connect and disconnect, off and on. And every time I troubleshoot it, a message comes up saying there's a network cable not properly plugged in or broken... It's been doing this for about a year and I usually just tap the bottom of the laptop or something and the wifi connects again but now it refuses to turn back on, how do I fix this?

  Read the article

• AutoHotKey - change mouse position and click a specific key every time window comes up

  - by John

  I'm a newbie to AHK, learning the basics. I'm using Notepad as an example - I want to hit the Cancel key every time I close Notepad and it asks if I want to Save/Don't Save/Cancel. I've come up with the script below and it works once but then I have to reload the script to do it again. I want it to hit Cancel every time the question box comes up. I thought Loop would work but am doing something wrong. Any ideas why, anyone? Loop IfWinExist Notepad, { WinWait Notepad WinActivate Click 312, 109 return }

  Read the article

• Stop Mac OS X from switching Spaces with mouse

  - by mankoff

  Mac OS X Spaces change when I drag a window at the edge of the screen. Is there an application or 'defaults' command to disable this? Warp looks like it might help, but hasn't changed the behavior for me, even though I tried turning it off, or setting a modifier key.

  Read the article

• Compatible wireless smart home systems with harmony 1100

  - by Markii

  Which technologies are compatible with the 1100? z wave, x10, hai, etc... I just want to start off with something simple like controlling the lights with the 1100.

  Read the article

• channel interference in cisco wireless access points 1130ag

  - by baskaran

  hello all, i am working as a network admin . in our client company we are eabling more than 70 access point in these 5 are outdoor access points . in this outdoor access points i am getting channel interference is failed , i have changed the channel manually through wlc . at that time only i am getting passed ,after that again it will be failed . so wt should i do ,please help me.

  Read the article

• European wireless data

  - by drewk

  I am on my way to Europe for 20 days with the wife and teenage kids. Among us, we have 3 iPhones, 1 Blackberry, 2 iPad 3G and 2 Macbook Pro laptops. Each has Skype. I am very concerned about AT&T data charges, and I am looking for a sensible alternative. For example, the AT&T data plans for the phones and iPads are $200 EACH for 200 MB per device. That is $1,200 and does not even cover the laptops. Ouch!!! I am thinking about a prepaid data plan from a European cell system of some sort combined with a GSM data modem and a Cradlepoint router, such as the CTR500. So, questions: 1) Anyone know of a GSM data source in Europe where I can buy a GSM Modem compatible with the CTR500 at a reasonable prepaid rate? 2) Experience with the CTR500?

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >