Search Results

Search found 34397 results on 1376 pages for 'php socket'.

Page 1120/1376 | < Previous Page | 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127  | Next Page >

• Joining two routers together, but I have no access to the second router, although I know it's IP address and Gateway

  - by JohnnyVegas

  I have temporarily moved into a rented apartment for 4 months, which has wireless. The trouble I am having is that the access points here are wifi only and no RJ45 and I need to use RJ45 to connect some equipment that I am working with. I have purchased an RT-N66U and installed Tomato (shibby ver. 1.28) and successfully replaced the existing access point, but now I want to enable the access point that I have replaced as it links wirelessly to 3 others. Can I plug in a cable from the access point to my RT-N66U and get it to access the internet via my router? I have no access to the existing wireless access point, and don't want to reset it as it's not mine. There is another router situated in the roof somewhere which I also have no access to, but it's supplying my RT-N66U internet and I most definitely have a double-nat, which although isn't the best way of doing things I am limited with what I can do. Any suggestions on routing tables, vlans etc would be helpful, but I have no experience in these fields before - but I know the tomato firmware can cater for this. My router is set to IP 10.0.1.1 and dhcp is 10.0.1.100-200 The wireless access point address was 192.168.1.2 but this was assigned by the router in the roof which has the address 192.168.1.1. There is a cable from this router going to a wall socket which I now have my RT-N66u attached to via the WAN port. I understand it's scruffy and it isn't the way to do things but I have tried to ask for the admin details but as the wireless network is looked after by a third party and nobody knows their details I am stuck with this dilemma. I could buy three wireless access points and replace the existing but this isn't what I want to do, and although I have installed plenty of DD-WRT wireless repeater bridges they simply don't work here for some unknown reason. The phone line here is very noisy too and I don't have the rights to install ADSL in a building that isn't mine, and 3G coverage isn't good enough either. Thanks for your time

  Read the article

• Step-by-step to run a midi keyboard input device? 12.04

  - by Mittenchops

  I have a Korg Nanokey, and I'd like to make it produce sound in ubuntu. I've read that means I should be using Rosegarden, and that Rosegarden uses JACK, but does not install it. (Although checking out Ubuntu Software Center, apparently some components of JACK are installed by default?) I understand there can be a lot of work setting up JACK without it fighting the default sound server. Can someone give me a step-by-step method for what I need to do to plug in my midi machine and hear music when I press keys as simply as possible (without messing up pulseaudio, ie, so I can still access Skype and ordinary desktop stuff)? I'm fine installing JACK, but I'd like to sandbox it a little if it has the chance of messing up regular desktop. I've looked through a couple resources, but I'm not sure what's outdated, but the following looked helpful... http://ubuntuforums.org/showthread.php?t=1686497 http://jackaudio.org/pulseaudio_and_jack

  Read the article

• Nginx all subdomain points to one subdomain (gitlab) rule

  - by Alkimake

  I have installed gitlab on my server and use nginx as http server... I simply used recipe for gitlab on nginx # GITLAB # Maintainer: @randx # App Version: 3.0 upstream gitlab { server unix:/home/gitlab/gitlab/tmp/sockets/gitlab.socket; } server { listen 192.168.250.81:80; # e.g., listen 192.168.1.1:80; server_name gitlab.xxx.com; # e.g., server_name source.example.com; root /home/gitlab/gitlab/public; # individual nginx logs for this gitlab vhost access_log /var/log/nginx/gitlab_access.log; error_log /var/log/nginx/gitlab_error.log; location / { # serve static files from defined root folder;. # @gitlab is a named location for the upstream fallback, see below try_files $uri $uri/index.html $uri.html @gitlab; } # if a file, which is not found in the root folder is requested, # then the proxy pass the request to the upsteam (gitlab unicorn) location @gitlab { proxy_read_timeout 300; # https://github.com/gitlabhq/gitlabhq/issues/694 proxy_connect_timeout 300; # https://github.com/gitlabhq/gitlabhq/issues/694 proxy_redirect off; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_pass http://gitlab; } } gitlab.xxx.com works fine and i get gitlab web documents. But if i want another subdomain i use for Jira (jira.xxx.com) on port 80 (i setup jira on 8080 port normally) gets gitlab web site also. How can i restrict this rule only serving for gitlab, or may be i can redirect jira.xxx.com to jira.xxx.com:8080

  Read the article

• Odd IIS FTP Failure

  - by Monkey Boson

  We're running a script on our production box that zips up our database and FTPs it to a backup box every night. Our production box is running Redhat Enterprise 5. Our backup box is running Windows XP Pro / IIS 5.1. Both machines are on the same VLAN (not sure if this is imporatant). The backup file usually clocks in at around 3GB. Every now and again (~5% of the time), the backup script fails. The shell script on the "client side" - which looks at return codes - never identifies any problem since ftp always returns 0. On the "server side", IIS writes out a log that looks like this: #Software: Microsoft Internet Information Services 5.1 #Version: 1.0 #Date: 2009-08-08 07:04:25 #Fields: time c-ip cs-method cs-uri-stem sc-status sc-win32-status 07:04:25 192.168.111.235 [15]USER backup 331 0 07:04:25 192.168.111.235 [15]PASS - 230 0 07:05:54 192.168.111.235 [15]created backup_20090808.zip 426 10035 07:06:16 192.168.111.235 [15]QUIT - 426 0 Now, I know that 426 means "Connection closed, transfer aborted", which is sort-of a catch-all for "IIS was not happy". The real puzzler is the wincode: 10035 (WSAEWOULDBLOCK -- Resource temporarily unavailable). My understanding is that this code is normal when using non-blocking socket calls - which would almost certainly be used by any FTP Server implementation. My first guess that it might be a timeout issue doesn't make sense, since we're only talking about a few minutes here and the timeout was left at the default 900 s. Does anybody have any ideas about what is causing this problem, and how it may be fixed? Thanks!

  Read the article

• django, mod_wsgi, MySQL High CPU - Problems

  - by Red Rover

  Good Evening, and thank you for reading this post. I am having a problem with Django after migrating the dB from SQLlite to MySQL. Initially, for the first 48hours, all ran well. But now we are experiencing high cpu about every 30 minutes. This is a production ESX4i VM host, with 2 x 2.8 ghz CPUs and 12 GB ram. I have allocated 4 cpu's to this VM and 4 GB memory. Any insight into this configuration and help with the spikes in CPU would be appreciated. IT is configured to use the prefork MPM. Outlined are the config's for the different services: MySQL Server version: 5.1.61 Source distribution Django 1.3 mod_wsgi Apache/2.2.15 httpd.conf Timeout 120 KeepAlive Off MaxKeepAliveRequests 400 KeepAliveTimeout 3 prefork MPM StartServers 8 MinSpareServers 8 MaxSpareServers 16 ServerLimit 40 MaxClients 40 MaxRequestsPerChild 0 worker MPM StartServers 16 MaxClients 1024 MinSpareThreads 64 MaxSpareThreads 256 ThreadsPerChild 64 MaxRequestsPerChild 10240 MySQL my.conf [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid my.cnf wsgi.conf LoadModule wsgi_module modules/mod_wsgi.so /etc/httpd/conf.d/wsgi.conf WSGISocketPrefix /var/run/wsgi WSGIPythonEggs /var/tmp WSGIDaemonProcess SITE maximum-requests=10000 WSGIProcessGroup SITE

  Read the article

• ADSL with RFC 2684 Bridging

  - by Axel Isouard

  My new ADSL line is now enabled, I can finally use my Netgear DM111Pv2 to use to the Internet. My ISP has told me a big surprise : I don't need to use a login and a password to connect to the Internet, then I must use the RFC 2684 bridging mode. It works pretty fine on the ADSL modem's side, but I've spent one night trying to figure out how to connect to the Internet through this modem. I only have a Fonera 2.0n and a computer running Gentoo Linux. I've been trying to use the br2684ctl utility with brctl on my Gentoo, first I've configured my kernel in that way : CONFIG_PPP=y CONFIG_PPP_BSDCOMP=y CONFIG_PPP_DEFLATE=y # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y # CONFIG_PPP_MULTILINK is not set CONFIG_PPPOATM=y CONFIG_PPPOE=y CONFIG_PPP_ASYNC=y CONFIG_PPP_SYNC_TTY=y [...] CONFIG_ATM=y CONFIG_ATM_CLIP=y CONFIG_ATM_CLIP_NO_ICMP=y CONFIG_ATM_LANE=y CONFIG_ATM_MPOA=y CONFIG_ATM_BR2684=y # CONFIG_ATM_BR2684_IPFILTER is not set And I still get these messages : cirus nais # br2684ctl -b -c 0 -e 0 -a 8.35 br2684ctl[8041]: Interface "nas0" created sucessfully br2684ctl[8041]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[8041]: Fatal: failed to connect on socket; No such device The brctl utility keeps telling me "Invalid argument" each time I try to add the nas0 interface into my bridge, I'm honestly hoping I'm doing wrong. I've been following this README carefully and this tutorial on setting up a PPPoE connection with Gentoo, but the PPPoE interface just tries to start, and nothing special related to PPP happens, I can't see the interface when I do ifconfig. So, I'm asking you if there's something huge I've been missing since the beginning ! Maybe I should wait to buy a new router fully supporting the RFC2684 bridging mode, but I'm more interested in setting up this mode on my Fonera 2.0n and even my Raspberry Pi !

  Read the article

• Installing Mysql Ruby gem on 64-bit CentOS

  - by Jacek

  Hi, I have a problem installing mysql ruby gem on 64bit CentOS machine. [jacekb@vitaidealn ~]$ uname -a Linux vitaidealn.local 2.6.18-92.el5 #1 SMP Tue Jun 10 18:51:06 EDT 2008 x86_64 x86_64 x86_64 GNU/Linux Mysql and mysql-devel packages are installed. Mysql_config provides following paths: Usage: /usr/lib64/mysql/mysql_config [OPTIONS] Options: --cflags [-I/usr/include/mysql -g -pipe -Wp,-D_FORTIFY_SOURCE=2 -fexceptions -fstack-protector --param=ssp-buffer-size=4 -m64 -mtune=generic -D_GNU_SOURCE -D_FILE_OFFSET_BITS=64 -D_LARGEFILE_SOURCE -fno-strict-aliasing -fwrapv] --include [-I/usr/include/mysql] --libs [-L/usr/lib64/mysql -lmysqlclient -lz -lcrypt -lnsl -lm -L/usr/lib64 -lssl -lcrypto] --libs_r [-L/usr/lib64/mysql -lmysqlclient_r -lz -lpthread -lcrypt -lnsl -lm -lpthread -L/usr/lib64 -lssl -lcrypto] --socket [/var/lib/mysql/mysql.sock] --port [3306] --version [5.0.45] --libmysqld-libs [-L/usr/lib64/mysql -lmysqld -lz -lpthread -lcrypt -lnsl -lm -lpthread -lrt -L/usr/lib64 -lssl -lcrypto] Trying to install: [jacekb@vitaidealn ~]$ gem install mysql -- --with-mysql-include=/usr/include/mysql --with-mysql-libs=/usr/lib64/mysql ... ERROR: Error installing mysql: ERROR: Failed to build gem native extension. /usr/bin/ruby extconf.rb --with-mysql-include=/usr/include/mysql --with-mysql-libs=/usr/lib64/mysql checking for mysql_query() in -lmysqlclient... no checking for main() in -lm... no checking for mysql_query() in -lmysqlclient... no checking for main() in -lz... no checking for mysql_query() in -lmysqlclient... no checking for main() in -lsocket... no checking for mysql_query() in -lmysqlclient... no checking for main() in -lnsl... no checking for mysql_query() in -lmysqlclient... no *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. I would appreciate any help. Thanks for reading :).

  Read the article

• Ubuntu server PPTPD with OS X clients Problems

  - by Nakedsteve

  I'm trying to get a PPTP server running on a ubuntu server, but I've run into some issues with it. I followed this guide on how to set up pptpd on my server, and everything went smooth, but when I try to connect with my mac, it gives me this error: Here's my configuration: Does anyone have any idea as to what I'm doing wrong here? Update: Here's what the pptpd.log has to say about it: steve@debian:~$ sudo tail /var/log/pptpd.log sudo: unable to resolve host debian Sep 3 21:46:43 debian pptpd[2485]: MGR: Manager process started Sep 3 21:46:43 debian pptpd[2485]: MGR: Maximum of 11 connections available Sep 3 21:46:43 debian pptpd[2485]: MGR: Couldn't create host socket Sep 3 21:46:43 debian pptpd[2485]: createHostSocket: Address already in use Sep 3 21:46:56 debian pptpd[2486]: CTRL: Client 192.168.1.101 control connection started Sep 3 21:46:56 debian pptpd[2486]: CTRL: Starting call (launching pppd, opening GRE) Sep 3 21:46:56 debian pptpd[2486]: GRE: read(fd=6,buffer=204d0,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Sep 3 21:46:56 debian pptpd[2486]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Sep 3 21:46:56 debian pptpd[2486]: CTRL: Reaping child PPP[2487] Sep 3 21:46:56 debian pptpd[2486]: CTRL: Client 192.168.1.101 control connection finished My pptpd options are: asyncmap 0 noauth crtscts lock hide-password modem debug proxyarp lcp-echo-interval 30 lcp-echo-failure 4 nopix

  Read the article

• Mobile redirect strategy

  - by Kevin

  Looking for help on deciding how to redirect users to a mobile optimized version of my site (m.mysite.com). Looking at two methods: Server configuration (.htaccess or even varnish) Webapp (php) The problem I see with #1 is with the "view full site" link on the mobile site. If a user clicks that link and they go to mysite.com won't the server just redirect them back to m.mysite.com? For #2 I could create a cookie that is checked in addition to the user agent. Any suggestions/comments? Is there a better way to "remember" if the user clicked "visit full site"? Thanks, Kevin

  Read the article

• Objective-c Cocos2d moving a sprite

  - by marcg11

  I hope someone knows how to do the following with cocos2d: I want a sprite to move but not in a single line by using [cocosGuy runAction: [CCMoveTo actionWithDuration:1 position:location]]; What I want is the sprite to do some kind of movements that I preestablish. For example in some point i want the sprirte to move for instance up and then down but in a curve. Do I have to do this with flash like this documents says? http://www.cocos2d-iphone.org/wiki/doku.php/prog_guide:animation Does animation in this page means moving sprites or what? thanks

  Read the article

• How to build a turn-based multiplayer "real time" server

  - by jmosesman

  I want to build a TCG for mobile devices that is multiplayer over the web (not local wifi or bluetooth). As a player plays cards I want the second player to see what is being played in "real time" (within a few seconds). Only one player can play at a time. Server requirements: 1) Continuously listens for input from Player 1 2) As it receives input from Player 1, sends the message to Player 2 I know some PHP, but it seems like unless I had a loop that continued until I broke it (seems like a bad idea) the script would just receive one input and quit. On the mobile side I know I can open sockets using various frameworks, but what language allows a "stream-like" behavior that continuously listens/sends messages on the server? Or if I'm missing something, what would be the best practice here?

  Read the article

• UPS with a HP Proliant server

  - by Groo

  We placed a EATON Ellipse Max 1500 (900W) as the UPS for our HP Proliant ML350 G6. Upon first power failure (actually we only moved the UPS' input plug to a different socket), server immediatelly turned off, and the Health LED turned red and started blinking. UPS was in operation for about a week before that, with battery fully charged to 100%. Since our server's hot-plug supply is 460W, we are pretty sure we haven't overloaded it, the server was completely idle at that time (no web or win apps running except Windows Server core services). Then we tried to do the same with a different, no-name older PC (Core 2 Duo, 2Gb RAM) with a generic power supply (not sure what the power is) and it continued working when we pulled the plug out. UPS load was less than 15% (measured in the provided Eaton utility). We measured the UPS' output voltage using a smart oscilloscope and the THD of the UPS output waveform turned out to be 40%. Did you have similar experiences? Could this be a faulty UPS? Or a faulty power supply? Or some HP sensors configured to trigger too strictly? I wouldn't like replacing this UPS with the same brand, to get same results. [Edit] I also tried to do this while the server is turned off. While the UPS is working on battery, server will not start - as soon as I press the power button, Health LED starts blinking red.

  Read the article

• Useful utilities - PFE, Notepad++ and XML Notepad 2007

  - by TATWORTH

  All three editors are free to download and use!  PFE http://www.lancs.ac.uk/staff/steveb/cpaap/pfe XML Notepad 2007 http://www.microsoft.com/downloads/details.aspx?familyid=72d6aa49-787d-4118-ba5f-4f30fe913628&displaylang=en Notepad++ http://notepad-plus.sourceforge.net/uk/download.php PFE development has stopped and I have included it mainly for reference. It does however have the facility to: Run DOS commands and capture the output Run simple macros XML Note Pad 2007 is excellent if you need to data values from attributes or elements. Notepad++ has various add-ons available for it. - When you download it, be sure to run its internal update function. Needless to say, all three are better than Notepad!

  Read the article

• Will taking two years off for school destroy my 4 year old development career?

  - by rsteckly

  Hi, I know some people have asked about getting back into programming after a break and this is a potential duplicate. I just am in a position where I can go back to school in Stat/Applied Math. But I'm very worried about the impact it will have on my career and ability to find a job afterwards. I have 3 years experience in .NET on top of a couple of years in PHP. Right now, I'm a senior software engineer. Do you think taking two years off to do math is going to dramatically hurt my marketability?

  Read the article

• Terms and conditions for a commerce site

  - by Mantorok

  I am developing a website for my partner who is currently a sole trader, presently selling on ebay but we have opted to create our own site. I've noticed that there are many sites allowing you to purchase base-line T&Cs to be used on websites, I'm tempted to give these a go but I've heard nothing on whether they are any good or not, I know in this position it's best to seek legal advice, but the budget is tight so we really can't afford that. Has anyone had experience with these sites? e.g. http://www.netlawman.co.uk/ecomm-it/website-terms-and-conditions.php?gclid=CPL4g8D3q6cCFQoa4Qodhj5UBg. Thanks

  Read the article

• dual-boot (win-xp/ubu12.04) graphics card for ubu-desktop/win-xp-games

  - by iole1

  for work I need to get a a new and cheap graphics card for a dual boot machine: windows xp/ubuntu 12.04 LTS. The only requirements I have are: it should work 'flawlessly' in ubuntu (proprietary drivers are ok) it should handle Guild Wars 2 & League of Legends in windows xp (this is really the top priority as we need to be able to play at work :) - yes I have a cool job) I know nothing about graphics cards (and it seems to be a jungle out there). From other questions here and some webstigation I think I'd like to go for a Nvidia card, I've been trying to figure out what models fit the system req's but it seems they use different kind of model numbers so I don't get any wiser. tl;dr: will http://www.geforce.co.uk/hardware/desktop-gpus/geforce-gt-620-oem/specifications run Guild Wars 2 http://gamesystemrequirements.com/games.php?id=938 Or what is the worst card from nVidia that will run GW2 smoothly and work well in Ubuntu 12.04 Thanks!

  Read the article

• How do I run Sim City 4?

  - by Jacob Larson

  I know that it is possible to run Sim City 4 Deluxe, as this page clearly proves so. http://appdb.winehq.org/objectManager.php?sClass=version&iId=10515 I have tried two different commands, and the paths are all right, but when I enter them, I simply get a blank terminal line. WINEDEUB=-all wine C:\\Program\ Files\ \(x86\)\\Maxis\\SimCity\ 4\ Deluxe\\Apps\\SimCity\ 4.exe -d:software -intro:off -CPUCount:1 env WINEPREFIX="/home/jacob/.wine" wine "C:\Program Files (x86)\Maxis\SimCity 4 Deluxe\Apps\SimCity 4.exe" -intro:off -CPUCount:1 So, what could be the problem? I'm fairly new, so I'm not really sure what info I need to provide. Thanks.

  Read the article

• Accessing SSH_AUTH_SOCK from another non-root user

  - by Danny F

  The Scenario: I am running ssh-agent on my local PC, and all my servers/clients are setup to forward SSH agent auth. I can hop between all my machines using the ssh-agent on my local PC. That works. I need to be able to SSH to a machine as myself (user1), change to another user named user2 (sudo -i -u user2), and then ssh to another box using the ssh-agent I have running on my local PC. Lets say I want to do something like ssh user3@machine2 (assuming that user3 has my public SSH key in their authorized_keys file). I have sudo configured to keep the SSH_AUTH_SOCK environment variable. All users involved (user[1-3]), are non privileged users (not root). The Problem: When I change to another user, even though the SSH_AUTH_SOCK variable is set correctly, (lets say its set to: /tmp/ssh-HbKVFL7799/agent.13799) user2 does not have access to the socket that was created by user1 - Which of course makes sense, otherwise user2 could hijack user1's private key and hop around as that user. This scenario works just fine if instead of getting a shell via sudo for user2, I get a shell via sudo for root. Because naturally root has access to all the files on the machine. The question: Preferably using sudo, how can I change from user1 to user2, but still have access to user1's SSH_AUTH_SOCK?

  Read the article

• Installing MySQL 5.1 on OS X 10.7 Lion

  - by xisal

  I am trying to install MySQL 5.1. I am on Lion, and when I remove all files associated with MySQL on my machine it still tells me that I have a newer version installed when I try to install it from the DMG file. Has anyone successfully installed MySQL 5.1 on Lion? I found a solution using Homebrew: Completely remove MySQL from your system (just in case) sudo rm /usr/local/mysql sudo rm -rf /usr/local/mysql* sudo rm -rf /Library/StartupItems/MySQLCOM sudo rm -rf /Library/PreferencePanes/My* vim /etc/hostconfig and removed the line MYSQLCOM=-YES- rm -rf ~/Library/PreferencePanes/My* sudo rm -rf /Library/Receipts/mysql* sudo rm -rf /Library/Receipts/MySQL* sudo rm -rf /var/db/receipts/com.mysql.* Source:http://stackoverflow.com/questions/1436425/how-do-you-uninstall-mysql-from-mac-os-x Install homebrew /usr/bin/ruby -e "$(curl -fsSL https://raw.github.com/gist/323731)" Source: https://github.com/mxcl/homebrew/wiki/installation Install MySQL 5.1 via brew brew install mysql51 if that doesn't work, do this: brew install https://raw.github.com/adamv/homebrew-alt/master/versions/mysql51.rb Source: http://stackoverflow.com/questions/4359131/brew-install-mysql-on-mac-os/6399627#6399627 Make MySQL Work Create mysql.sock file touch /tmp/mysql.sock Install MySQL default tables /usr/local/Cellar/mysql51/5.1.58/bin/mysql_install_db ...or your path Source: http://stackoverflow.com/questions/4788381/getting-cant-connect-through-socket-tmp-mysql-when-installing-mysql-on-ma/5140849#5140849

  Read the article

• What must be done to allow a development team to minimize difficulties as new team members are added?

  - by Travis

  I work at a small Web Dev firm, and have been handling all the PHP/MySQL/etc. for a while. I'm looking at improving our practices to allow for easier collaboration as we grow. Some things I have in mind are: Implementing a versioning system (source control) Coding standards for the team (unless mandated by a certain framework, etc.) Enforcing a common directory structure for our Desktops (for backup purposes, etc.) Web-based task/project/time/file/password/contact management and collaboration app(we've tried a bunch; I may just create one) What do more experienced developers view as necessary first steps in this area? Do you recommend any books? One thing to consider is that the bulk of our daily tasks involve maintenance and adding minor functionality rather than new projects, and the team size will be between 3 and 5. I just found a related question about teams that will be expanding from a solo developer.

  Read the article

• Understanding the static keyword

  - by user985482

  I have some experience in developing with Java, Javascript and PHP. I am reading Microsoft Visual C# 2010 Step by Step which I feel it is a very good book on introducing you to the C# language. I seem to be having problems in understanding the static keyword. From what I understand this far if a class is declared static all methods and variable have to be static. The main method always is a static method so in the class that the main method exists all variables and methods are declared static if you have to call them in the main method. Also I have noticed that in order to call a static method from another class you do not need to create an object of that you can use the class name. What are the advantages of declaring static variables and methods? When should I declare static variable and methods?

  Read the article

• Java doesn't show up in firefox plugins

  - by user857990

  I've just installed the newest java, because firefox blocks the old version. I used the tutorial from http://www.backtrack-linux.org/wiki/index.php/Java_Install Because I had some trouble once, I knew that there are multiple library folders, so I linked into all mozilla plugin folders that there are. /root/.mozilla/plugins /usr/lib/firefox/plugins/ /usr/lib/firefox-addons /usr/lib/mozilla/plugins /usr/lib64/mozilla/plugins java -version returns java version "1.7.0_07" Java(TM) SE Runtime Environment (build 1.7.0_07-b10) Java HotSpot(TM) 64-Bit Server VM (build 23.3-b01, mixed mode) But when I go to firefox plugins, it's not listed. What do I need to do, so that firefox recognizes java?

  Read the article

• Authenticating Active Directory Users to Mac OS X Mavericks Server L2TP VPN Service

  - by dean

  We have a Windows Server 2012 Active Directory Infrastructure that consists of two domain controllers. Bound to the Active Directory Domain is a Mac OS X Mavericks Server 10.9.3. The server runs Profile Manager and VPN Services. My Active Directory users are able to authenticate to the Profile Manager, but not the VPN. I have found several threads on other forums of other users reporting similar issues, here is just one of many references: https://discussions.apple.com/thread/5174619 It appears as though the issue is related to a CHAP authentication failure. Can anyone suggest what next troubleshooting steps I might take? Is there a way to liberalize the authentication mechanism to include MSCHAP? Here is an excerpt of the transaction from the logs. Please note the domain has been changed to example.com. Jun 6 15:25:03 profile-manager.example.com vpnd[10317]: Incoming call... Address given to client = 192.168.55.217 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: publish_entry SCDSet() failed: Success! Jun 6 15:25:03 --- last message repeated 2 times --- Jun 6 15:25:03 profile-manager.example.com pppd[10677]: pppd 2.4.2 (Apple version 727.90.1) started by root, uid 0 Jun 6 15:25:03 profile-manager.example.com pppd[10677]: L2TP incoming call in progress from '108.46.112.181'... Jun 6 15:25:03 profile-manager.example.com racoon[257]: pfkey DELETE received: ESP 192.168.55.12[4500]->108.46.112.181[4500] spi=25137226(0x17f904a) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP connection established. Jun 6 15:25:04 profile-manager kernel[0]: ppp0: is now delegating en0 (type 0x6, family 2, sub-family 0) Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connect: ppp0 <--> socket[34:18] Jun 6 15:25:04 profile-manager.example.com pppd[10677]: CHAP peer authentication failed for alex Jun 6 15:25:04 profile-manager.example.com pppd[10677]: Connection terminated. Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnecting... Jun 6 15:25:04 profile-manager.example.com pppd[10677]: L2TP disconnected Jun 6 15:25:04 profile-manager.example.com vpnd[10317]: --> Client with address = 192.168.55.217 has hung up

  Read the article

• Web development starting a career [closed]

  - by user985482

  Hi I am in the 3rd and last year at college of informatics and I am interested to follow a career in web development when I finish(2 more months). From what I understand this days to get hired you need to be able to know a variety of technologies at least that is the case in Romania.Most of the jobs I have seen even at entry level asks you to know the following: HTML/CSS Javascript , a framework preferable jQuery , Ajax a server side language in my case PHP and a framework SQL and an RDBMS in my case MySql a CMS in my case Wordpress My question is how well should me or anyone looking to get hired as a web developer for there first job should we know this technologies in order to get hired and what else should we aim to learn to have a better chance of getting hired. I don't know if the question is right for this forum but I believe that this could help many of the students and anyone who is taking an interest in web development to know what they should expect from there employers when they try to find work.

  Read the article

• I don't really understand "Backend/Serverside" when it comes to web-development?

  - by Mercfh

  In the Web development world, what exactly do backend/server-side programmers do? I guess I don't really understand the whole concept. I've done the HTML/CSS layouts and website design and a little bit of SQL with PHP (still enhancing my skills, it's more of a side project for me). I've also done a small amount of JavaScript/JQuery. But I don't understand the "backend" work, such as the scripting languages (Rails/Python/etc) and such. What exactly do you "do" with them? Are there any books on the subject? I'm not even sure what it means. Is it kinda like what Web Application Frameworks do? Or not so much?

  Read the article

< Previous Page | 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127  | Next Page >