Search Results

Search found 4096 results on 164 pages for 'intel 8086'.

Page 114/164 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• CentOS default installation gave 60% disk space to tmpfs partition

  - by garconcn

  I installed a CentOS server which will be used for xen hypervisor. The server has two Intel(R) Xeon(R) CPU E5620 and 148G memory. The OS was installed on a 120G SSD drive. After the installation, I found that the tmpfs partition occupied about 60% of the drive. Even though I don't need much space for the OS, will there be any problem with 71G tmp partition? Thanks for any comment. [root@cloud ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 55G 1.1G 51G 3% / /dev/sda1 99M 13M 82M 14% /boot tmpfs 71G 0 71G 0% /dev/shm

  Read the article

• Choosing A Power Supply [closed]

  - by Geeks On Hugs

  Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

  Read the article

• update ocz vertex le capacity via firmware update

  - by Ben Voigt

  I have an OCZ Vertex LE 100GB drive. It's actually 128GiB of NAND flash, with a whopping 28%+ reserved for write combining. Most 128GiB drives are actually ~ 115GB usable (and marketed as 120GB or 128GB). There were rumors that the reserved fraction could be decreased on OCZ 100GB drives. Can anyone provide a link to firmware that does that, or an official statement that no such firmware exists? (NB: I recently installed the 1.24 firmware from the OCZ site, it didn't affect the capacity. Possibly because the rumors say the capacity change is destructive to existing content.) Of possible interest: flashing firmware was more of a pain than it should have been -- the tool didn't detect the disk until I booted an older Windows install off a secondary hard disk, I suspect the Intel SATA driver is the issue and tool only works with the msachi.sys driver.

  Read the article

• Time Machine (archive) of pre-Leopard systems?

  - by benc

  I want to get off an older Mac OS X system permanently. It is an iBook G3, so that has two important characteristics: Power PC, not Intel based. Runs only Tiger, not Leopard. This means, as far as I can tell: Cannot run Time Machine directly. Here's the approach I have been contemplating: Mount the drive in Firewire mode. Back up the drive as a external drive to the Time Machine volume. Disconnect the drive (permanently). However, I'm concerned that this drive will eventually age out, when the Time Machine volume fills up, and the old-system-as-external-drive is gone. Would it be better to do a single backup with another utility, to shared disk?

  Read the article

• Artefacts during HDV capture

  - by Jakub Konecki

  When I try to capture HDV video stream from a Canon HV20 camera to a Dell Studio 1558 (Intel i7 720qm) laptop running Win 7 Home Premium x64, the image appears with a very annoying noise - it contains block artefacts. Something is wrong with the Fire Wire controller (Ricoh 1304 OHCI host controller, build-in). Tried changing the driver to legacy one to no avail. This does not happen with DV stream. I'm using a Belkin cable. The capture works OK on another machine.

  Read the article

• How many VPS' can I create on my server?

  - by user197692

  I need to create as many VPS's on my dedicated server (KVM or OpenVZ) in order to sell them but I really don't know the answer. RAM calculation is simple, it's more about CPU resources, how many VPS's can hold. I'am talking about Intel i7-2600 (4 cores, 8 Threads). I need to deploy as many VPS's. It's all about the nr threads? i.e. 8 threads = maximum 8 x 1vCPU or maximum 4 x 2vCPU? I'am planning to use 1Gb and 2Gb memory on each VPS, the server has 16Gb (but I can raise RAM if need it. So, can I create 8 KVM VPS's with 4 vCPU and 2Gb ram each ? How about 20 VPS's with 1Gb ram and 4vCPU each? How is this decision affected by the hypervisor (KVM, OpenVZ, VMware)?

  Read the article

• Is a ext3 Linux filesystem byte order independent

  - by Lothar

  I have a good old HP-C3700 Workstation with PA-RISC CPU here that I would like to use as a subversion server for a very large repository. I just worry what happens if the workstation dies (everybody who knows this computer knows that it is running like an Abrams tank and unlikely to happen in the next decade). I'm using Debian Linux on this system. If the mainboard dies can I just plug the SCSI drive into a PC and read the files from a normal Intel Linux PC? Which software RAID levels would be safe?

  Read the article

• My KDE very slow in certain operations

  - by Pietro

  I have a problem with my Linux installation. It seems that the KDE code that deals with directory windows is extremely slow (on both Dolphin and Konqueror). This happens both when I click on a directory icon and when I want to open/save a file from many KDE applications. The time the window takes to open can be one minute or more. The same happens when I right click on an icon. Looking at the CPU usage, this is very low (less than 10%). Am I the only one with this problem, or is it well known and maybe already fixed? Consider that I cannot update to a more recent version of OpenSuse. Thank you, Pietro Configuration: Linux version: OpenSuse 11.4 KDE 4.6.0 System: DELL Precision T3500 - Intel Xeon Home directory mounted on a remote drive. <-- could this be the reason?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the last Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the latest Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• HDD situation - what would be best - data and backup

  - by Sam Johnson

  I just installed W8 on an Intel 330 180 GB SSD. I have 3 1TB HDDs. 1 HDD will be external for backup. 2 HDDs are then available for my PC. I do not need 2 TB of storage, so I thought I'd set these up to be exact clones of one another, so that if one dies I have a backup in the computer to go along with my external. Is this a good set up? How best would this be accomplished? I've heard people suggest RAID but I've never done RAID, have no idea what it is, and have no idea how to set it up in my BIOS. Thanks in advance

  Read the article

• How can I disable DPMS temporarily in X under a modern linux?

  - by wrt

  Historically if you wanted to control blanking and DPMS in X, you could do it with xset. Issuingxset -dpms on my laptop results in xset q returning "DPMS is Disabled", as it should. But my screens still turn off. I'm running an up-to-date Arch Linux using KMS with integrated Intel graphics, I'm not running GNOME or willing to use anything that needs something like it. I am however stuck with DBUS and HAL. I've tried fiddling with the various timeouts, and it hasn't helped - specifically, changing the timeouts seems to be able to turn off the screen sooner, but not stop it from turning off :) This makes me suspect that there's something else overriding the setting. Is there any way to get xset to actually function as it used to, or at least stop lying to me? Note that I don't want to permanently disable DPMS or blanking - just to be able to control it when I need to.

  Read the article

• Computer won't start unless power is removed for ~5 minutes

  - by Paul Tarjan

  I have a fairly standard 2-year old desktop computer (quad-core intel, single hard drive, decent video card, 300W power supply) which recently started acting up. I'm not sure what the cause is, so hopefully you can help. Sometimes (once a week-ish) I press the power button and nothing happens. No blinking, no sounds, no nothing. If I remove the power cord (or flip the switch on the power supply) I hear a capacitor discharge. If I leave it in the "no power at all" state for about 5 minutes then I can put the plug back in and the computer works perfectly. What is the issue? What do you think I have to replace?

  Read the article

• Configuration Tuning for PostgreSQL 9.1 PostGIS 1.5 Ubuntu 12.04 Server

  - by Martin

  My server performance is poor. At times SSH, top, and other features or commands are very slow to respond, taking several seconds or more. A query that normally takes 5 minutes can sometimes take 30 minutes. The database is mostly being used to do a spatial query (grid and summarize) on approximately 500GB of stored data spread between 4 tables. Restarting the server works as a temporary fix, but cannot be used as a long term solution. Any suggestions for how to diagnose and solve my performance issues? Hardware and Configuration: 3.3 GHz Intel quad core i5 16 GB DDR3 RAM 6 TB software RAID 10 (6 x 2 TB drives) Ubuntu 12.04 64-bit Postgres 9.1 PostGIS 1.5

  Read the article

• Is there a test to see if hardware virtualization (vmx / svm) are presently enabled within a Linux session?

  - by Dr. Edward Morbius

  I'm writing procedures for configuring VirtualBox support for 64-bit SMP guests, which requires hardware virtualization suppot (VTx/Intel, AMD-V/AMD). I have successfully configured this myself, however I'd like the procedure to be clear. sed -ne '/^flags/s/^.*: //p' /proc/cpuinfo | egrep -q '(vmx|svm)' && echo Has hardware virt || echo No HW virt ... shows if the CPU is capable. I've still got to go enable the feature in BIOS. Any way to test from within Linux to see that this is no or not? Thanks. (Edit: s/xvm/svm/ in title)

  Read the article

• Computer won't start unless power is removed for ~5 minutes

  - by Paul Tarjan

  I have a fairly standard 2-year old desktop computer (quad-core intel, single hard drive, decent video card, 300W power supply) which recently started acting up. I'm not sure what the cause is, so hopefully you can help. Sometimes (once a week-ish) I press the power button and nothing happens. No blinking, no sounds, no nothing. If I remove the power cord (or flip the switch on the power supply) I hear a capacitor discharge. If I leave it in the "no power at all" state for about 5 minutes then I can put the plug back in and the computer works perfectly. What is the issue? What do you think I have to replace?

  Read the article

• Hearing repeated sound in Linux mint Chrome Browser

  - by aravind.udayashankara

  I am using Linux mint OS since an Year , I use to consistently download updates and install , I use chrome as a default browser , when ever I open youtube and watch some video , I listen to some repetition in sound ( say repeated lyrics of song ) while it is playing , In firefox it is working fine . What is the problem am I missing any plugin , AFAIK Chrome doesn't need a flash player plug in , It has a built in flash player . IS that the problem ? And also previously I was not facing this , recently I started using Cinimon UI centOS after this all these kind of problems started MY hard ware is 64 bit intel core i3 and also I have installed linux mint 64 bit Please let me know what is the problem and how to fix this . Thanks in advance for responding to this post

  Read the article

• Unable to boot Ubuntu 64-bit in Virtualbox on Mac OS X

  - by Aamir

  I have latest generation Macbook Pro 7.1 (Intel Core 2 Duo) running Mac OS X 10.6.6. I installed Virtuabox 4.0.2 and tried to boot Ubuntu 10.10 64-bit iso. The boot options screen from the live CD came up: However when I continued to load the live session, or installer for that matter, I encountered the following error: This kernel requires an x86-64 CPU, but only detected an i686 CPU. Unable to boot - please use a kernel appropriate for your CPU. I am not sure if VT-x is enabled or is supported in the Core 2 Duo of my Macbook Pro. But at least, I have both I/O APIC and VT-x enabled for hardware virtualization as told in the Virtualbox manual.

  Read the article

• Cannot enter BIOS due to broken screen

  - by gamer

  Lately my laptop(hp g42 247sb) screen is damaged, so I hook it up with a external monitor(LG something) and it works fine now. But the only annoying thing is I cannot navigate the BIOS menu for some tweaking because the BIOS not shown on the external monitor,instead, it only shown on the broken laptop screen, and it only output to my external monitor when windwos/os is loged-on. So, is there anyway I can force output during BIOS/BOOT/POST to my external monitor? Things I have done and didn't work: (1)Set my LG monitor as primary display on both window properties and Intel Graphics panel (2)Enter the bios (F10 key) and press the fn+F4 key(change display output). (3)Disable and uninstall my internal screen(broken laptop screen) using device manager and restart, but windows(bios?) install it back on log-on. Please help me!

  Read the article

• Why does Midori on Fedora Linux pretend to be Safari on Mac OS X?

  - by Suhail Gupta

  If you are using Google Chrome on Linux then the User-Agent request header will look like this: Mozilla/5.0 (X11; Linux i686) AppleWebKit/537.1 (KHTML, like Gecko) Chrome/21.0.1180.89 Safari/537.1 From above we come to know the browser is Chrome and OS is Linux (I guess!). But when I log from the browser Midori using the same OS which is Linux (Fedora) I get to see this: Mozilla/5.0 (Macintosh; U; Intel Mac OS X; en-us) AppleWebKit/535+ (KHTML, like Gecko) Version/5.0 Safari/535.4+ Midori/0.4 Why does it say Macintosh?

  Read the article

• How to force my laptop to use the discrete GPU?

  - by Anton Roth

  My laptop (Asus X7BSV) is stuck using only the integrated GPU. It has a nVidia GT540M as well, but I cannot get it to work. I am using a Windows 7 x64 with latest drivers. This occurred after I attached an external USB monitor I need for work, and since then I cannot swap back to the nVidia GPU (dxdiag for example says that the primary GPU is the Intel integrated one). Asus support asked me to completely reinstall the system, but that is something I do not want to do. I checked the BIOS, there is no option as to what GPU to use. The nVidia card itself is working, since I can use CUDA on it, and it worked with a Ubuntu Live CD. In the nVidia software management I tried setting it to global setting, high performance GPU (nVidia), but that had no impact. What am I missing here? I did uninstall/delete all drivers and software related to the external monitor, but that did not help.

  Read the article

• Can I run ubuntu server 64 bit in a VirtualBox on a macbook host ?

  - by Doron

  Hello, I have a macbook pro with Intel Core 2 Due (It's actually not Pro, but it's a January 2009 unibody macbook - when there were both a unibody macbook, and a unibody macbook pro). I'm a php developer. I just installed a new hard drive, and in an effort to create a better development environment, I decided I'll try to create a virtual machine running ubuntu server. Since I need it to work fast (and since, well - it's just better, even if by a little) and I'll already have a delay due to the nature of the apache server being on a virtual host - I want to install a 64 bit version of ubuntu server. Can VirtualBox handle it? Is it s good idea to create such a development environment ? Thank you.

  Read the article

• how to install Mysql & tomcat on mac os x 10.5.8

  - by Divya Jyothi

  Hi can some one provide me how to install both om my mac osx 10.5.8 Hi can some one provide me how to install both om my mac osx 10.5.8 Ok this what I have done Downloaded MySQL version 5.5.22.dmg for Mac OS X 10.5 (x86, 64-bit) from http://dev.mysql.com/downloads/mysql/ Installed three files from it after mounting.... 1.MySQL -version.pkg installed it by double clicking on it 2.mysqlstartupitem.pkg installed it 3. MySql.prefpane - after installing it says it doesn't work on intel based Mac After that I have no idea whati need to start Regarding tomcat JAVA_HOME WAS the problem;(

  Read the article

• Win 2003 STD network adapter always showing DHCP when in static IP configuration, + it loses the DNS

  - by Darragh

  Hi, I have a server that after the first configuration it was DHCP, now I have added it to our domain and in a static IP, however after a few moments it returns to DHCP but with only some of the IPv4 setting staying the same, It loses DNS for example. I'm not sure what is causing the problem but all I know is this started to happen after I added it to the domain, Would it be a domain policy? or the NIC drivers Spec; Dell M605 Blade server Windows 2003 STD SP1 Intel Xeon Quad core NIC: Dual embedded Broadcom NetXtreme IITM 5708 Gigabit Ethernet NIC w/ TOE

  Read the article

• Win7 backup fails with "The system cannot find the file specified" 0x80070002 - has worked before

  - by Thorbjørn Ravn Andersen

  I have a 500 GB USB-disk which has been used as a backup device for a few years now, but now fails without telling me why. This is a Dell box with Intel USB-controllers (so the NVIDEA problem does not apply here). I have previously had problems with a Git package marking a non-existent directory for backup (adding it make the backup succeede). The inaccessible boot partition problem described in Windows Backup fails with 0x80070002: "The system cannot find the file specified" does not apply to me. I would appreciate hints on where to look to identify why my backup fails so I can fix it.

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >