Search Results

Search found 5333 results on 214 pages for 'mem fun ref'.

Page 114/214 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• How do I Connect a 30yr-old Tandy 1400LT laptop to the internet?

  - by Clemens Bergmann

  Just for the fun of it, I want to get an old Tandy 1400LT laptop: small monochrome display two floppy drives rs-232c connector "printer" connector connect the thing the internet and use it as an ssh terminal. How would I connect it to the internet? The software should be no problem as it is a 386 hardware. There should be a small linux distribution which can be run on it. But how would I phisically connect the hardware? It has no ethernet port. Has someone experience with Serial/Paralel-to-ethernet converters?

  Read the article

• Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

  - by Jeff Carr

  I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

  Read the article

• How do I boot [embedded] linux from sd card?

  - by Brandon Yates

  I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

  Read the article

• Sysprep on Windows 7 for a non-windows admin?

  - by askvictor

  I'm needing to use sysprep to deploy some Windows 7 machines. I can't find any resources that explain this very easily. In particular, I've loaded all of the programs I want for the image onto a computer. If I want to use prepares this for cloning onto 200 other machines, what steps would I need to take? Or do I need to start again, creating the image using 'audit' mode? The machines I'm using come pre-configured from the manufacturer with a host of custom drivers that wouldn't be fun to re-install - I'd rather use their base image to build upon. Cheers, Victor

  Read the article

• High apache load but zero traffic

  - by Adie

  I have a problem with new server.. I use VPS Centos with 1GB of ram and I use wordpress CMS. The traffic <100 visitor/hour, but the apache have high load and make the server hang with zero free of ram and can't connect through ssh. I should reboot the vps to make it works here is the load on Apache looks like Tasks: 66 total, 1 running, 65 sleeping, 0 stopped, 0 zombie Cpu(s): 1.6%us, 12.3%sy, 0.0%ni, 48.1%id, 23.0%wa, 4.8%hi, 10.2%si, 0.0% Mem: 1018776k total, 116620k used, 902156k free, 1236k buffers Swap: 1048568k total, 1013052k used, 35516k free, 26628k cached 2949 apache 20 0 459m 42m 3732 D 3.0 4.2 0:09.23 httpd 2959 apache 20 0 460m 29m 3744 D 2.0 3.0 0:02.72 httpd 2968 apache 20 0 460m 26m 3808 D 2.0 2.6 0:02.27 httpd 2972 apache 20 0 460m 24m 3784 D 2.0 2.5 0:02.44 httpd 2986 apache 20 0 460m 29m 3784 R 2.0 2.9 0:02.40 httpd 2969 apache 20 0 458m 29m 3864 D 1.6 3.0 0:02.63 httpd 2974 apache 20 0 460m 25m 3820 D 1.6 2.6 0:02.43 httpd 2990 apache 20 0 460m 23m 3920 D 1.6 2.4 0:02.36 httpd 2994 apache 20 0 460m 31m 3756 D 1.6 3.2 0:02.62 httpd 2956 apache 20 0 460m 26m 3740 D 1.3 2.7 0:02.73 httpd 2957 apache 20 0 465m 22m 3644 D 1.3 2.3 0:02.80 httpd 2967 apache 20 0 458m 24m 3764 D 1.3 2.5 0:02.60 httpd 2970 apache 20 0 463m 25m 3764 D 1.3 2.6 0:03.07 httpd 2971 apache 20 0 451m 22m 3792 D 1.3 2.3 0:02.47 httpd 2973 apache 20 0 458m 25m 3768 D 1.3 2.6 0:02.52 httpd 2987 apache 20 0 465m 20m 3772 D 1.3 2.1 0:03.02 httpd But sometimes the server have uptime more than 5-10hrs but after that the problems start

  Read the article

• Setting up Windows network on Xen

  - by samyboy

  I'm trying to install a Windows XP server in a Xen environment. The OS is booting fine. Unfortunately I can't figure out how to set up the network settings. Dom0 is a Debian Lenny currently hosting around 10 Linux virtual servers. Windows tells me I have a "limited connection". It can't get any DHCP response, nor access other hosts in the network Here is the Xen's client config file: kernel = '/usr/lib/xen-3.2-1/boot/hvmloader' builder = 'hvm' memory = '1024' device_model='/usr/lib/xen-3.2-1/bin/qemu-dm' acpi=1 apic=1 pae=1 vcpus=1 name = 'winexchange' # Disks disk = [ 'phy:/dev/wnghosts/exchange-disk,ioemu:hda,w', 'file:/mnt/freespace/ISO/DVD1_Installation.iso,ioemu:hdc:cdrom,r' ] # Networking vif = [ 'mac=00:16:3E:0A:D0:1B, type=ioemu, bridge=xenbr0'] # video stdvga=0 serial='pty' ne2000=0 # Behaviour boot='c' sdl=0 # VNC vfb = [ 'type=vnc' ] vnc=1 vncdisplay=1 vncunused=1 usbdevice='tablet' Server config (/etc/xen/xend-config.sxp) (network-script network-bridge) (network-script network-dummy) (vif-script vif-bridge) (dom0-min-mem 512) (dom0-cpus 0) (vnc-listen '0.0.0.0') Since I use Debian I had to create a link like this: /etc/xen/qemu-ifup - /etc/xen/scripts/qemu-ifup What did I do wrong? Please tell me if you want some more info (logs, etc)

  Read the article

• Libvirt / QEmu Machine Fails and Refuses Restart Because of Memory Allocation Errors

  - by Elmar Weber

  I'm having a problem with libvirt. On a system restart all virtual machines (VMs) are started without a problem and keep running. Then at some point in time a set of machines shuts down according to their log. When I try to restart the machine, I'm getting an error that the memory allocation failed, although more than enough memory is free. server ~ # free total used free shared buffers cached Mem: 16176648 16025476 151172 0 285432 950300 -/+ buffers/cache: 14789744 1386904 Swap: 0 0 0 server ~ # virsh start zimbra error: Failed to start domain zimbra error: Unable to read from monitor: Connection reset by peer server ~ # tail -n 4 /var/log/libvirt/qemu/zimbra.log LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 3072 -smp 2,sockets=2,cores=1,threads=1 -name zimbra -uuid d05ddb7a-83c4-a77b-d8bc-a322648520cf -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/zimbra.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=control -rtc base=utc -no-shutdown -drive file=/var/lib/libvirt/images/zimbra.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0,bootindex=1 -netdev tap,fd=19,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:21:a9:ad,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 192.168.1.2:25 -k de -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/2 Failed to allocate 3221225472 B: Cannot allocate memory 2012-07-06 08:42:56.076+0000: shutting down server ~ # uname -a Linux server 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux The system is a Ubuntu 12.04 server. The problem seems to occurs since the last restart, which was due to a number of package upgrades and a kernel upgrade. I tried booting with the previous kernel, the problem persists. I was not able to pinpoint an exact event when the machines fail, they do it at nearly the same time. The last time a duplicity job was running, this was not always the case however. Any suggestions on how to debug this? Best regards, elm

  Read the article

• load average in top and procs in vmstat

  - by Mingfei.hua

  As far as I know, the load average in top is the numbers of precess(threads) in running or uninterrupted sleep status, So it should be equal to (procs-r +1 )+ procs-b in vmstat, but in practice, this two number always have big gap. Any wrongs in my understanding, appreciate so much if some guys give me some guide. top - 05:34:50 up 1 day, 20:56, 5 users, load average: 2.83, 2.67, 1.62 Tasks: 79 total, 1 running, 78 sleeping, 0 stopped, 0 zombie Cpu(s): 6.8%us, 1.8%sy, 0.0%ni, 91.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.4%st Mem: 1758000k total, 582636k used, 1175364k free, 103932k buffers Swap: 917500k total, 0k used, 917500k free, 180868k cached procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu----- r b swpd free buff cache si so bi bo in cs us sy id wa st 0 0 0 1182524 103784 180860 0 0 1 9 6 53 7 2 91 0 0 0 0 0 1182524 103784 180860 0 0 0 36 70 117 0 0 100 0 0 0 0 0 1182516 103784 180860 0 0 0 0 73 132 0 1 100 0 0 0 0 0 1182516 103784 180860 0 0 0 0 60 127 0 0 100 0 0 1 0 0 1182516 103784 180860 0 0 0 0 62 102 0 0 100 0 0 0 0 0 1182628 103784 180860 0 0 0 0 289 238 1 2 97 0 0 2 0 0 1152160 103784 180892 0 0 0 8 1481 2371 54 12 34 0 0 1 0 0 1182192 103784 180860 0 0 0 0 681 834 19 4 78 0 0 0 0 0 1182200 103784 180860 0 0 0 0 80 147 0 1 100 0 0 0 0 0 1182200 103784 180860 0 0 0 0 53 107 0 0 100 0 0 0 0 0 1182208 103788 180856 0 0 0 72 64 123 0 0 100 1 0

  Read the article

• How to change drag & drop behaviour in Windows 7's explorer?

  - by Pekka

  I have a new touch screen, and am playing around with its functionality. The most productive use for me is organizing files (literally) by hand. It's fun working through a list of files, dragging and dropping them to the right locations using your index finger. It feels better on the wrist than mouse-clicking, too. The only problem is that when I drag & drop files across drives in Windows 7, the default behaviour is to copy the file instead of moving it. I know I can influence this using right click, but that is of course no option in my situation. How can I change the default drag & drop behaviour in Windows 7's explorer?

  Read the article

• RHEL 5.2 installing on ProLiant BL460c - hangs at 'now booting the kernel'

  - by Dr Rocket Mr Socket

  As the title states, I have a problem. This server and the installation disc are also on the other side of the world to me so... So far, I have tried to start the install with the parameters: linux text noapic noacpi no=apic no=acpi which results in the same hang. I have also disabled a PCI ethernet adapter, I am uneasy about disabling the onboard ethernet adapter I do not know if ILO uses this. Anyone have any advice? Much appreciated. EDIT: full output after trying to begin the installation. boot: linux text Loading initrd.img.................. Loading vmlinuz....... Uncompressing Linux...done. Now booting the kernel stays on this for hours EDIT2: adding the 'mem=40960M' (server has 40 gigs of ram) parameter allows it to proceed but the following output directly after 'Now booting the kernal' Memory: sized by int13 0e801h initrd extends beyond end of memory (0x00ef2090 > 0x00000000) disabling initrd Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory Structure at 0x000ffee0 pcibios_init : BIOS32 Service Directory entry at 0xf0000

  Read the article

• How to debug a kernel created using ubuntu-vm-builder?

  - by user265592

  Aim: Trying to perform a code walkthrough of what functions are getting called for sending and receiving packets over the network. I am building a kernel and using gdb for debugging/ tracing purposes. I have build a vm using the following command : time sudo ubuntu-vm-builder qemu precise --arch 'amd64' --mem '1024' --rootsize '4096' --swapsize '1024' --kernel-flavour 'generic' --hostname 'ubuntu' --components 'main' --name 'Bob' --user 'ubuntu' --pass 'ubuntu' --bridge 'br0' --libvirt 'qemu:///system' And I can run the VM successfully in qemu using the following command: qemu-system-x86_64 -smp 1 -drive file=tmpGgEOzK.qcow2 "$@" -net nic -net user -serial stdio -redir tcp:2222::22 Now, I want to debug the kernel using gdb. For this I need an executable with debug symbols(vmlinux), which apparently I don't have, as the vm-builder never asked for any such options and simply created a .qcow2 file. Question 1: Am I taking the correct approach to solve the problem and is there an easier way to do it? Question 2: Is there a way to debug this kernel using GDB? P.S: I don't have hardware support for KVM. Please correct me if I am wrong. Thanks.

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• FFMPEG Segfault Solutions

  - by Brentley_11

  I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

  Read the article

• RAID administration in Debian Lenny

  - by Siim K

  I've got an old box that I don't want to scrap yet because it's got a nice working 5-disk RAID assembly. I want to create 2 arrays: RAID 1 with 2 disks and RAID 5 with the other 3 disks. The RAID card is Intel SRCU31L. I can create the RAID 1 volume in the console that you access with Ctrl+C at startup. But it only allows for creation of one volume so I can't do anything with the 3 remaining disks. I installed Debian Lenny on the RAID 1 volume and it worked out nicely. What utilites could I now use to create/manage the RAID volumes in Debian Linux? I installed the raidutils package but get an error when trying to fetch a list: #raidutil -L controller or #raidutil -L physical # raidutil -L controller osdOpenEngine : 11/08/110-18:16:08 Fatal error, no active controller device files found. Engine connect failed: Open What could I try to get this thing working? Can you suggest any other tools? Command #lspci -vv gives me this about the controller: 00:06.1 I2O: Intel Corporation Integrated RAID (rev 02) (prog-if 01) Subsystem: Intel Corporation Device 0001 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step ping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort - <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 26 Region 0: Memory at f9800000 (32-bit, prefetchable) [size=8M] [virtual] Expansion ROM at 30020000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: PCI_I2O Kernel modules: i2o_core

  Read the article

• RAM being displayed is lesser than the actual in my Windows 7

  - by Prateek Somani

  I am using Windows 7 and Ubuntu on the same machine. Earlier I had 3 GB of RAM,but now the Windows is displaying just 1 GB of RAM. Please also find the output of the free command in my Ubuntu : total used free shared buffers cached Mem: 1008208 904808 103400 5736 13516 239596 -/+ buffers/cache: 651696 356512 Swap: 3127292 10252 3117040 Has the swap memory consumed my 2 GB of RAM? Will I be able to use the whole of 3GB of the RAM in my Windows? Regards, Prateek Update : I tried to run the lshw command and I got the following output : *-memory description: System Memory physical id: 1b slot: System board or motherboard size: 1GiB *-bank:0 description: SODIMM DDR3 Synchronous 1067 MHz (0.9 ns) product: HMT112S6BFR6C-H9 vendor: Hynix physical id: 0 serial: 2C71D069 slot: Bottom - Slot 1 size: 1GiB width: 64 bits clock: 1067MHz (0.9ns) *-bank:1 description: SODIMM DDR3 Synchronous 1067 MHz (0.9 ns) [empty] product: 16JSF25664HZ-1G4F1 vendor: Micron physical id: 1 serial: FD421821 slot: Bottom - Slot 2 width: 64 bits clock: 1067MHz (0.9ns) Why it is able to detect the vendor/product name of the bank-1 RAM, why can't it detect the RAM size and other details ? Has my RAM got faulty?

  Read the article

• Mixing RAM brands

  - by Andy

  Hey guys, I'm scheduled to install a server at a colo facility tomorrow, but I've hit a snag. ESXi doesn't like the fact that I have 12GB ram in my server (8gb on one side of CPU, 4gb on the other). I currently have 3xCrucial 4gb ECC DDR3 1333mhz sticks (http://www.amazon.com/gp/product/B001TGT7EE/ref=oss_product) and I'm planning on stopping by Fry's on the way to the colo facility so I can pick up another stick so that ESXi will install. Problem is, Fry's doesn't stock Crucial RAM. They do have a stick that I think is identical to my crucial one: http://www.frys.com/product/5915524?site=sr:SEARCH:MAIN_RSLT_PG Will this be dangerous to use in my server? The specs on the RAM are the same as far as I know (ecc registered, 1333mhz, ddr3, 4gb).

  Read the article

• DNSHost.exe trojan found, now after fix, no one can print

  - by Matt Dawdy

  What started today as an inability to get to the internet (but people could get in just fine), morphed to we realized that the DNS Server wasn't working, then we figured out that we had a trojan called DNSHost.exe (spybot.rl I think), and we disabled its service entry and deleted the offending file and all registry keys told to use by the Trend Micro site. Now, we can get on the internet, but the printer being served by this machine (called server2) cannot be printed to from any client machine on the network. We get the error "The RPC Server is unavailable". I'm assuming that this is related to the DNS issue we had earlier, as we were able to print just fine until this fun happiness started this morning. Anyone have any solid suggestions? Windows Server 2003 R2 SP2, and the client machine are all Windows XP SP2.

  Read the article

• PostgresQL on Amazon EBS volume, realistic performance, or move to something more lightweight?

  - by Peck

  Hi, I'm working on a little research project, currently running as an instance on ec2, and I'm hoping to figure out whether I'm going down the right path. We, like a thousand other people, are making use of some of twitters streaming feeds to do gather some data to have fun with and my db seems to be having problems keeping up, and queries take what seems to be a very long time. I'm not a DBA by trade, so I'll just dump some info here and add more if need be. System specs: ec2 xl, 15 gigs of ram ebs: 4 100 gb drives, raid 0. The stream we're getting we're looking at around 10k inserts per minute. 3 main tables, with the users we're tracking somewhere in the neighborhood of 26M rows currently. Is this amount of inserts on this hardware too much to ask out of ebs? Should take a look at some things with less overhead like mongodb?

  Read the article

• Can I connect an external antenna to a range extender?

  - by ercan

  I live in a kind of dormitory and the next access point is 60 meters away from my room. So I bought a range extender (TP-Link WA730RE) and installed it into my room in the same height as the access point. But my problem is still not solved. The reception is slightly better but my connection still gets broken every two minutes. The antenna that comes with this range extender was 4dB. My question is, can I buy an 8dB external antenna (like this one: http://www.amazon.com/TP-Link-TL-ANT2408C-Desktop-Omni-Directional-Antenna/dp/B0034CQSKW/ref=sr_1_14?ie=UTF8&qid=1332074993&sr=8-14) and replace it with the antenna that comes with the range extender? Or is this external antenna only suitable for the "receiver" end of the connection, i.e. the computer?

  Read the article

• apache performance timing out

  - by Mike

  Im running a webserver where I'm hosting about 6-7 websites. Most of these websites get their content from MySQL which is hosted on the same server. Traffic average per day is about 500-600 unique visitors, about 150K hits per week. But for some reason sometimes websites send a timeout, OR sometimes websites dont load all images. I know that I should perhaps separate static content from dynamic content, but for now I think that's not a possibility. I would appreciate any suggestions on how could I improve the performance of apache, so it doesn't keep timing out. Server is running on Sempron LE 1300; 2.3GHz,512K Cache 2GB RAM 10Mbps/1Mbps Services: MySQL, ProFTPD, Apache. Private + Shared = RAM used Program ---------------------------------------------------- 1.2 MiB + 54.0 KiB = 1.2 MiB proftpd 4.1 MiB + 23.0 KiB = 4.1 MiB munin-node 20.8 MiB + 120.5 KiB = 20.9 MiB mysqld 47.3 MiB + 9.9 MiB = 57.3 MiB apache2 (22) top: Mem: 2075356k total, 1826196k used, 249160k free, Timeout 35 KeepAlive On MaxKeepAliveRequests 300 KeepAliveTimeout 5 <IfModule mpm_prefork_module> StartServers 10 MinSpareServers 20 MaxSpareServers 20 MaxClients 60 MaxRequestsPerChild 1000 </IfModule> <IfModule mpm_worker_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule>

  Read the article

• FFMPEG Segfault Solutions

  - by Brentley_11

  I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

  Read the article

• How hard for a Software Developer to Maintain a Server

  - by Samy

  I'm a software developer and don't have much experience as a sysadmin. I developed a web app and was considering buying a server and hosting the web app on it. Is this a huge undertaking for a web developer? What's the level of difficulty of maintaining a server and keeping up with the latest security patches and all that kind of fun stuff. I'm a single user, and not planning to sell the service to others. Can someone also recommend an OS for my case, and maybe some good learning resources that's concise and not too overwhelming.

  Read the article

• Finding Image resolution in PDF file?

  - by Dave

  I have a problem of having some users creating very large PDFs. On the other hands I have PDF sent from our fax machines that are really small in size and totally printable. My question is Is there any way I can find the resolution (DPI) of the PDF. I search the internet, could not find any answer. Checked the properties of the file, this information was not stored there, at least in my case. What is the optimum resolution of converting text file into image PDF. 96dpi, 300dpi or more ? Fun question. Can I resize a PDF which was scanned with high dpi into smaller dpi? I know some answers might not be available as I have already searched the internet and could not find answers. Note: My PDF are entirely images, text to images. I am also familiar with primoPDF (free) something you can experiment with

  Read the article

• Apache crashes a few seconds after the start.

  - by Nacho

  Hi, i've got a problem with apache. When i try to start it (/etc/init.d/apache2 start) it dies after a few seconds. It shows up on "ps aux" consuming a lot of memory and then dies. I don't know what could be causing apache to consume this amount of memory: USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 13379 1.0 0.3 14376 3908 ? Ss 22:31 0:00 /usr/sbin/apache2 -k start www-data 13383 0.0 0.4 197316 4196 ? Sl 22:31 0:00 /usr/sbin/apache2 -k start www-data 13390 0.0 0.3 172728 4172 ? Sl 22:31 0:00 /usr/sbin/apache2 -k start www-data 13396 0.0 0.3 156336 4160 ? Sl 22:31 0:00 /usr/sbin/apache2 -k start www-data 13400 0.0 0.3 148140 4156 ? Sl 22:31 0:00 /usr/sbin/apache2 -k start www-data 13403 0.0 0.3 131748 4148 ? Sl 22:31 0:00 /usr/sbin/apache2 -k start Here is a htop screenshot: http://i.imgur.com/N4Chh.png It happened suddenly, no change had been made to server config, so i don't know whats causing it. The error log of my virtual servers shows this: [Sun Jan 30 22:19:50 2011] [alert] (11)Resource temporarily unavailable: mod_wsgi (pid=9685): Couldn't create worker thread 11 in daemon process 'fb.ebookmetafinder.com'. [Sun Jan 30 22:19:55 2011] [alert] (11)Resource temporarily unavailable: mod_wsgi (pid=9685): Couldn't create worker thread 19 in daemon process 'fb.ebookmetafinder.com'. [Sun Jan 30 22:29:40 2011] [alert] (11)Resource temporarily unavailable: mod_wsgi (pid=12009): Couldn't create worker thread 18 in daemon process 'fb.ebookmetafinder.com'. [Sun Jan 30 22:31:06 2011] [alert] (11)Resource temporarily unavailable: mod_wsgi (pid=13396): Couldn't create worker thread 15 in daemon process 'fb.ebookmetafinder.com'. [Sun Jan 30 22:35:02 2011] [alert] (11)Resource temporarily unavailable: mod_wsgi (pid=14009): Couldn't create worker thread 16 in daemon process 'fb.ebookmetafinder.com'. [Sun Jan 30 22:35:07 2011] [alert] (11)Resource temporarily unavailable: mod_wsgi (pid=14009): Couldn't create worker thread 17 in daemon process 'fb.ebookmetafinder.com'. I'm on a ubuntu server vps and i use mod_wsgi with django. Thanks.

  Read the article

• IIS 7 with verisign certificate, invalid certificate returned

  - by bh213

  We have IIS7 on windows 2008 and we installed verisign certificate and bound it to https. Certificate seems fine. Chain: mysite.com - not expired VeriSign international server CA class 3 - not expired Verisign Class 3 Public primary certification Authority - not expired Yet when I use verisign online validation, I get that second certificate is expired. https://knowledge.verisign.com/support/ssl-certificates-support/index?page=content&id=AR1130# This is what it reports, mysite is reported to be ok: ---------------- --Issued To-- Organization: VeriSign Trust Network Organizational Unit: www.verisign.com/CPS Incorp.by Ref. LIABILITY LTD.(c)97 VeriSign Organizational Unit 2: VeriSign International Server CA - Class 3 Organizational Unit 3: VeriSign,, Inc. --Issued By-- Organization: VeriSign,, Inc. Organizational Unit: Class 3 Public Primary Certification Authority Country: US Validity Start: Wed Apr 16 17:00:00 PDT 1997 Validity End: Wed Jan 07 15:59:59 PST 2004 ---------------- Any ideas?

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >