Search Results

Search found 29437 results on 1178 pages for 'ubuntu membership'.

Page 114/1178 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121 | Next Page >

Ubuntu second static IP, ifconfig, /etc/network/interfaces

- by Schmoove

I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

Read the article
Ubuntu init.d script not being called on startup

- by Mike

I've got a script in ubuntu 9.04 in init.d that I've set to run on start on with update-rc.d using update-rc.d init_test defaults 99. All of the symlinks are there and the permissions appear to be correct -rwxr-xr-x 1 root root 642 2010-10-28 16:44 init_test mike@xxxxxxxxxx:~$ find /etc -name S99* | grep init_test find: /etc/rc5.d/S99init_test find: /etc/rc4.d/S99init_test find: /etc/rc2.d/S99init_test find: /etc/rc3.d/S99init_test The script runs through source and ./ without issue and behaves correctly. Here is the source of the script: #!/bin/bash ### BEGIN INIT INFO # Provides: init test script # Required-Start: $remote_fs $syslog # Required-Stop: $remote_fs $syslog # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: Start daemon at boot time # Description: Enable service provided by daemon. ### END INIT INFO start() { echo "hi" echo "start called" >> /tmp/test.log return } stop() { echo "Stopping" } echo "Script called" >> /tmp/test.log case "$1" in start) start ;; stop) stop ;; *) echo "Usage: {start|stop|restart}" exit 1 ;; esac exit $? When the machine starts, I don't see "script called" or "start called" in the test.log at all. Is there anything obvious I'm messing up?

Read the article
Unable to receive emails from Ubuntu postfix mail server

- by Paddington

I am unable to receive emails on an Ubuntu 11.04 server running postfix with the Plesk control panel. I can't see the mails even on webmail. I am able to send emails and am not getting any error messages on the email client when I try to receive. Here is the output of the logs: *tail -f /usr/local/psa/var/log/maillog Aug 29 10:38:31 cp9 postfix/tlsmgr[3811]: fatal: open database /var/lib/postfix/smtpd_scache.db: Invalid argument Aug 29 10:38:32 cp9 postfix/master[27738]: warning: process /usr/lib/postfix/tlsmgr pid 3811 exit status 1 Aug 29 10:38:32 cp9 postfix/master[27738]: warning: /usr/lib/postfix/tlsmgr: bad command startup -- throttling Aug 29 10:38:36 cp9 pop3d: Connection, ip=[::ffff:196.201.7.158] Aug 29 10:38:36 cp9 pop3d: IMAP connect from @ [::ffff:196.201.7.158]INFO: LOGIN, [email protected], ip=[::ffff:196.201.7.158] Aug 29 10:38:37 cp9 pop3d: 1346229517.874008 LOGOUT, [email protected], ip=[::ffff:196.201.7.158], top=0, retr=0, time=1, rcvd=24, sent=1716, maildir=/var/qmail/mailnames/essentialhuku.co.za/earle/Maildir Aug 29 10:14:05 cp9 postfix/tlsmgr[1133]: fatal: open database /var/lib/postfix/smtpd_scache.db: Invalid argument Aug 29 10:14:06 cp9 postfix/master[27738]: warning: process /usr/lib/postfix/tlsmgr pid 1133 exit status 1 Aug 29 10:14:06 cp9 postfix/master[27738]: warning: /usr/lib/postfix/tlsmgr: bad command startup -- throttling Aug 29 10:14:08 cp9 pop3d: Connection, ip=[::ffff:196.201.7.158

Read the article
Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

- by cpm

I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

Read the article
Mongrel Cluster on Ubuntu Server Karmic

- by trobrock

I am trying to get mongrel cluster working on my Ubuntu Server Karmic box in preparation to setup Capistrano. I've been trying to get the two to work all day and finally decided to completely remove Capistrano and see if I can just get Mongrel Cluster to work. I ran this to install mongrel cluster: gem install mongrel mongrel_cluster Everything installed fine, when I change into my app's directory... # mongrel_rails -bash: mongrel_rails: command not found I can run it from its install location: # /var/lib/gems/1.8/bin/mongrel_rails Usage: mongrel_rails <command> [options] Available commands are: ... It lets me build the cluster configuration file fine, but when I run the clister:start command: # /var/lib/gems/1.8/bin/mongrel_rails cluster::start starting port 8000 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8000 -P tmp/pids/mongrel.8000.pid -l log/mongrel.8000.log starting port 8001 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8001 -P tmp/pids/mongrel.8001.pid -l log/mongrel.8001.log starting port 8002 /usr/lib/ruby/1.8/rubygems/custom_require.rb:31: command not found: mongrel_rails start -d -e production -p 8002 -P tmp/pids/mongrel.8002.pid -l log/mongrel.8002.log It seems it isnt calling it from the right directory after that command, what can I do to fix this? I tried setting the path previously when trying to set up Capistrano, but the path didnt stay set when Capistrano used ssh to run the commands.

Read the article
Netbook (Samsung N220) on Ubuntu 10.04 slows down WiFi for other computers

- by Joachim

I encountered a really odd problem with my new netbook. I am running Ubuntu 10.04 on a Samsung N220 Mito. So far everything worked fine. Now I tried the machine for the first time in our work group where we have a wifi (with internet access) for all laptops. The wifi is controlled by a computer running Suse 9.3 which provides a DHCP server and imposes a firewall. At the moment there is only a macbook in the wifi, where no problems with the internet or wifi connection are encountered. Now coming to my actual problem: In addition to the macbook i connect the Samsung N220 to the Wifi. Problem: My download speed is for some reason limited to 70KB/s max. This is neither a limitation of the server/website i browse on, nor a configuration of the netbook: at home i have 500KB/s download speeds. Furthermore, it is not a default limitation for "untrusted" or "new machines" in the wifi, as for instance other new laptops get full speed internet with our wifi. Problem: Once the Samsung N220 is generating traffic in the wifi, the wifi is slowed down dramatically for all other machines: I run a ping to the router from the macbook. The ping times with the N220 ideling are 2-6ms. When I start downloading or browsing in the web with the N220 the ping speed drops to 800ms. Vice versa, when the macbook is generating the traffic the ping of the N220 to the rooter stays constant at around 2-6ms. So clearly, it is some problem originating from my netbook or maybe its treatment in the wifi. Thanks for any help

Read the article
php on ubuntu 13.10 won't get parsed

- by fefe

I'm facing a strange issue with a fresh installed ubuntu 13.10 apache2 with mysql and php. My php won't get parsed and I have been doing every changes what I found during my researches PHP 5.5.3-1ubuntu2 (cli) (built: Oct 9 2013 14:49:12) sudo a2enmod php5 apache2.conf <FilesMatch \.php$> SetHandler application/x-httpd-php </FilesMatch> /etc/apache2/mods-enabled/php5.conf </FilesMatch> # Deny access to files without filename (e.g. '.php') <FilesMatch "^\.ph(p[345]?|t|tml|ps)$"> Order Deny,Allow Deny from all </FilesMatch> # Running PHP scripts in user directories is disabled by default # # To re-enable PHP in user directories comment the following lines # (from <IfModule ...> to </IfModule>.) Do NOT set it to On as it # prevents .htaccess files from disabling it. #<IfModule mod_userdir.c> # <Directory /home/*/public_html> # php_admin_value engine Off # </Directory> #</IfModule>

Read the article
Setup: Eclipse in Ubuntu with Apache2 and Subversion

- by Ricalsin

Trying to setup Eclispe. I am running ubuntu 10.10 (Maverick). Apache2.2.16 Subversion 1.6.12 The Eclipse help/about/installed software says: Eclipse Platform 3.5.2 Subclipse 1.0.0 Version Control with Subversion 1.1.1 The Subclips wiki I followed is here I have installed the libsvn-java app as discussed. I added the line "-Djava.library.path=/usr/lib/jni" to the eclipse.ini file I checked the Eclipse help/about/confirguration settings and both of these lines are listed: eclipse.vmargs=-Djava.library.path=/usr/lib/jni java.library.path=/usr/lib/jni I checked that those files are in those directories. Still, when I check the preferencesteamsvn an error dialog shows: Failed to load JavaHL Library. These are the errors that were encountered: no libsvnjavahl.1 in java.library.path Incompatible JavaHL library loaded 1.3.x or later required I followed the "Testing JavaHL libraries" troubleshooting section at the bottom of the wiki: I downloaded the tarbal and ran it in a folder on my desktop with no problems. Then, I followed the instructions and placed that file INSIDE the path (usr/lib/jni/testJavaHL) and ran it from there. There are 50 tests performed and each one of them came back with this same error (posting only one for brevity): 50) testCommitRevprops(org.tigris.subversion.javahl.BasicTests)java.io.FileNotFoundException: /usr/lib/jni/testJavaHL/local_tmp/greek_files/iota (No such file or directory) at java.io.FileOutputStream.open(Native Method) at java.io.FileOutputStream.<init>(FileOutputStream.java:209) at java.io.FileOutputStream.<init>(FileOutputStream.java:160) at org.tigris.subversion.javahl.WC.materialize(WC.java:70) at org.tigris.subversion.javahl.SVNTests.buildGreekFiles(SVNTests.java:303) at org.tigris.subversion.javahl.SVNTests.setUp(SVNTests.java:222) at org.tigris.subversion.javahl.RunTests.main(RunTests.java:111) FAILURES!!! Tests run: 50, Failures: 0, Errors: 50 Any ideas as to how/why the "local_tmp/greek_files/iota" is appended to the directory? I assume that's my problem.. I'm also having a problem with newrepository location = ...as the directory location of my svn repository is one level above the home directory - which is prepended to whatever I place in the dialog box - resulting in this error: svn: '/home/ricalsin/file:/home/svn' does not exist Thank you for any help.

Read the article
Ubuntu upgrade process failed

- by Spin0us

I tried to dist-upgrade my ubuntu server on my percona cluster but it failed with this message The following packages have unmet dependencies: libmysqlclient18 : Depends: libmariadbclient18 (= 5.5.33a+maria-1~precise) but it is not installable And here is the package listing # dpkg --list | grep -E 'percona|mysql' ii libdbd-mysql-perl 4.020-1build2 Perl5 database interface to the MySQL database iU libmysqlclient18 5.5.33a+maria-1~precise Virtual package to satisfy external depends ii mariadb-common 5.5.33a+maria-1~precise MariaDB database common files (e.g. /etc/mysql/conf.d/mariadb.cnf) ii percona-xtrabackup 2.1.5-680-1.precise Open source backup tool for InnoDB and XtraDB ii percona-xtradb-cluster-client-5.5 5.5.31-23.7.5-438.precise Percona Server database client binaries ii percona-xtradb-cluster-common-5.5 5.5.33-23.7.6-496.precise Percona Server database common files (e.g. /etc/mysql/my.cnf) ii percona-xtradb-cluster-galera-2.x 157.precise Galera components of Percona XtraDB Cluster ii percona-xtradb-cluster-server-5.5 5.5.31-23.7.5-438.precise Percona Server database server binaries ii php5-mysql 5.3.10-1ubuntu3.8 MySQL module for php5 During the install of the server, mariadb and galera cluster have first been installed. Then removed to be replaced by percona XtraDBCluster. So i think this is the source of the problem. But how can i resolve this without reinstalling all ? UPDATE 1 # apt-cache policy libmariadbclient18 libmariadbclient18: Installed: (none) Candidate: (none) Version table: 5.5.32+maria-1~precise 0 100 /var/lib/dpkg/status

Read the article
Can't get rsync over sftp to work

- by Patrik

I'm trying to set up a backup system from an Ubuntu server to a Synology NAS (DS413j) using rsync and sftp. I have created a user for this that we can call ubuntu-backup. I have a directory in ubuntu-backup home directory called www where the backup will be saved. I have enabled Network Backup in DSM The user ubuntu-backup has full access to it's home directory Here is my rsync config file on the Synology NAS: #motd file = /etc/rsyncd.motd #log file = /var/log/rsyncd.log pid file = /var/run/rsyncd.pid lock file = /var/run/rsync.lock use chroot = no [NetBackup] path = /var/services/NetBackup comment = Network Backup Share uid = root gid = root read only = no list = yes charset = utf-8 auth users = root secrets file = /etc/rsyncd.secrets [ubuntu-backup] path = /volume1/homes/ubuntu-backup/www comment = Ubuntu Backup uid = ubuntu-backup gid = users read only = false auth users = ubuntu-backup secrets file = /etc/rsyncd.secrets The permissions on /volume1/homes/ubuntu-backup/www is ubuntu-backup:users 777 Here is the command i'm running. rsync -aHvhiPb /var/www/ [email protected]:./ The result: sending incremental file list ERROR: module is read only rsync error: syntax or usage error (code 1) at main.c(1034) [Receiver=3.0.9] rsync: connection unexpectedly closed (9 bytes received so far) [sender] rsync error: error in rsync protocol data stream (code 12) at io.c(605) [sender=3.0.9] If I'm running this: rsync -aHvhiPb /var/www/ [email protected] It looks like its sending files. No errors. But I cant find anything on the NAS.

Read the article
Dell OpenManage On Ubuntu Server 12.04 Cannot Log In

- by Austin

I have a Dell Poweredge 2950 with 2X130GB and 2X2TB drives. I need to set them up in a RAID 1 array so that the 130GB Drives are mirrored and host the OS, while the 2TB drives are mirrored and are the content drives. So I go from 4 disks, down to two, one 130GB and one 2TB. I can do that in the BIOS RAID utility no problem. But I need to be able to manage the RAID arrays and be able to expand them WITHOUT shutting down the server. Now, to my understanding, openmanage will allow me to do that AND it runs on ubuntu. So I go and set it up and try to log into the web interface at and it will not let me log in. I have followed dell's guide to set up openmanage, even added the usernames to the files and permissions and such, however, cannot get it to let me log in or anything. I have reinstalled Openmanage several times, even reinstalled the OS three times, and nothing works. Google does not help either. It simply says login failed after hitting submit. Please Help

Read the article
Ubuntu Equivalent of Unix Command cp -n

- by Ted Karmel

A software I need to install on my Ubuntu Hardy has a MAKE file which includes the command cp -n. However, I get an error stating the -n is an invalid option. The command will work on a Mac terminal but I need it to work on Ubuntu. Does anyone know the equivalent command for Ubuntu? Thanks.

Read the article
Debian/Ubuntu - No network connection

- by leviathanus

I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

Read the article
How to install rmagick on Ubuntu 10.04?

- by Andrew

Here's what I've done so far: sudo apt-get install imagemagick libmagickcore-dev This did not throw any errors, so I think that ImageMagick is installed fine. Then I tried installing the gem: sudo gem install rmagick This resulted in the following error: ERROR: Error installing rmagick: ERROR: Failed to build gem native extension. /usr/bin/ruby1.8 extconf.rb checking for Ruby version >= 1.8.5... yes checking for gcc... yes checking for Magick-config... yes checking for ImageMagick version >= 6.4.9... yes checking for HDRI disabled version of ImageMagick... yes checking for stdint.h... yes checking for sys/types.h... yes checking for wand/MagickWand.h... no Can't install RMagick 2.13.1. Can't find MagickWand.h. *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. Provided configuration options: --with-opt-dir --without-opt-dir --with-opt-include --without-opt-include=${opt-dir}/include --with-opt-lib --without-opt-lib=${opt-dir}/lib --with-make-prog --without-make-prog --srcdir=. --curdir --ruby=/usr/bin/ruby1.8 Gem files will remain installed in /usr/lib/ruby/gems/1.8/gems/rmagick-2.13.1 for inspection. Results logged to /usr/lib/ruby/gems/1.8/gems/rmagick-2.13.1/ext/RMagick/gem_make.out What do I need to do to install rmagick on Ubuntu 10.04?

Read the article
Samba4/Ubuntu Shares Incorrectly Available to All Users

- by Dan

I've got my Ubuntu server working with Samba4 and got it set up as the Primary domain controller on my network with AD and all that goodness. However, I'm trying to get my Samba configuration to work with the users and groups I've defined with the Active Directory tools from Windows. For instance, I've got a share X which I want users A and B (as part of the 'management' group, known as LLGrpManager in my setup) to see, but no body else. However, after making changes to the configuration, restarting Samba, I test by connecting to the share with my Mac over Samba as user 'C' which isn't part of the management group, and I can, incorrectly, see the X share. I've tried alsorts of combinations of specifying the group with no luck at all. I've got a feeling that my global config might be too lenient or something to do with file permissions but being a bit green, I'm without clue. My /etc/samba/smb.conf # Global parameters [global] server role = domain controller server string = Office Server workgroup = LLDOMAIN realm = lldomain.local netbios name = DUMBO passdb backend = samba4 logon path = \\%L\profiles\%U logon drive = L: log file = /var/log/samba/%m.log max log size = 50 security = ads domain logons = yes domain master = auto usershare allow guests = no valid users = %S [netlogon] path = /var/lib/samba/sysvol/lldomain.local/scripts read only = no guest ok = no [sysvol] path = /var/lib/samba/sysvol read only = No guest ok = no valid users = @LLDOMAIN\LLGrpManager [ShareX] path = /data comment = Entire Data Volume guest ok = no comment = Entire Data Volume guest ok = no valid users = @LLDOMAIN\LLGrpManager admin users = @LLDOMAIN\LLGrpManager browsable = no inherit acls = yes inherit permissions = yes ... My /etc/nsswitch.conf I've also instructed the system to use the nss winbind library when searching for users or groups by adding the stanza passwd and group in /etc/nsswitch.conf: passwd: compat winbind group: compat winbind shadow: compat Permissions on the folder in question drwxrwxrwt 8 root root 4.0K Oct 28 19:11 data

Read the article
Wireless does not work on Ubuntu 9.04

- by Yongwei Xing

Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

Read the article
Access to File being restricted after Ubuntu crashed

- by Tim

My Ubuntu 8.10 crashed due to the overheating problem of the CPU when I am opening some directory and intend to do some file transfer under Nautilus. After reboot, under gnome, all the files cannot be removed, their properties cannot be viewed and they can only be opened, although all are still fine under terminal. I was wondering why is that and how can I fix it? Thanks and regards UPdate $ cat /etc/mtab /dev/sda7 / ext3 rw,relatime,errors=remount-ro 0 0 tmpfs /lib/init/rw tmpfs rw,nosuid,mode=0755 0 0 /proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 varrun /var/run tmpfs rw,nosuid,mode=0755 0 0 varlock /var/lock tmpfs rw,noexec,nosuid,nodev,mode=1777 0 0 udev /dev tmpfs rw,mode=0755 0 0 tmpfs /dev/shm tmpfs rw,nosuid,nodev 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=620 0 0 fusectl /sys/fs/fuse/connections fusectl rw 0 0 lrm /lib/modules/2.6.27-15-generic/volatile tmpfs rw,mode=755 0 0 /dev/sda8 /home ext3 rw,relatime 0 0 /dev/sda2 /windows-c vfat rw,utf8,umask=007,gid=46 0 0 /dev/sda5 /windows-d fuseblk rw,allow_other,blksize=4096 0 0 securityfs /sys/kernel/security securityfs rw 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,noexec,nosuid,nodev 0 0 gvfs-fuse-daemon /home/tim/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,user=tim 0 0

Read the article
Is ASP.NET membership, role management and Profile usable in a C# Class Library?

- by afsharm

I know it's possible to use this information in a winform, wpf or console application. But I rather to determine which user with what roles are running a sepecific method, so I could decide upon them and run different codes. In addition in a desktop app. how a user can login? Is there any special winform or wpf login control?

Read the article
SNMP Access on Ubuntu

- by javano

I am trying to use SNMP to monitor a machine locally on its self and remotely. This is the snmpd.conf (Ubuntu 8.04.1): # sec.name source comunity com2sec readonly 1.2.3.4 nicenandtight com2sec readonly 5.6.7.8 reallysafe group MyROGroup v1 readonly group MyROGroup v2c readonly group MyROGroup usm readonly view all included .1 view system included .iso.org.dod.internet.mgmt.mib-2.system access MyROGroup "" any noauth exact all none none syslocation my house syscontact me <[email protected]> exec .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro smuxpeer .1.3.6.1.4.1.674.10892.1 includeAllDisks 95% 1.2.3.4 is the local machines IP and everything is working locally. 5.6.7.8 is the remote machine and initially I am just trying to touch SNMPD with snmpwalk from the remote machine; snmpwalk -v 2c -c reallysafe 1.2.3.4 Timeout: No Response from 1.2.3.4 I have added to iptables as the very first rule; -A INPUT -p udp -m udp --dport 161 -j ACCEPT With such a loose iptables rule I can't see why I can't even touch the SNMPD on that Uubuntu Machine. There are more specific rules further down the table but as I couldn't connect I added the above. TCPDump shows the UDP packets coming in. What could be going wrong here?

Read the article
Install VirtualBox on Ubuntu 12.04.1 (on [Samsung] Chromebook)

- by iphonedev7

I have dual booted Ubuntu Linux 12.04.1 LTS on my Samsung Series 5 ChromeBook, and am trying to run/install Oracle VirtualBox (from the generic .run file downloaded from their website). However, every time I try to run it (as root from the command line), it gives me the following error occurs: Please install the build and header files for your current Linux kernel. The current kernel version is 3.4.0 Problems were found which would prevent VirtualBox from installing. I have tried the version from the Software Center, as well as the command line installation, both of which gave me errors based on my linux-headers/linux-kernel/linux-[kernel]-image. Here's an error I keep getting (on the command line): First Installation: checking all kernels... It is likely that 3.4.0 belongs to a chroot's host Building only for 3.5.0-18-generic Building initial module for 3.5.0-18-generic ERROR (dkms apport): kernel package linux-headers-3.5.0-18-generic is not supported Error! Bad return status for module build on kernel: 3.5.0-18-generic (x86_64) Consult /var/lib/dkms/virtualbox/4.1.12/build/make.log for more information. Setting up virtualbox-qt (4.1.12-dfsg-2ubuntu0.2) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place ...And one of the more cryptic errors I get when trying to start any Virtual Machine: Result Code: NS_ERROR_FAILURE (0x80004005) Component: Machine Interface: IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}

Read the article
setting up phpmyadmin with nginx within ubuntu 11.04

- by Patrick

I have nginx and php5-fpm running on ubuntu 11.04. I have installed phpmyadmin but im having trouble accessing it. I would like to access it via http://localhost/phpmyadmin I've used all the default locations for the nginx, php5, and phpmyadmin installs. I'm being directed to use the block below by the blog guide im following, but im not sure what to change to get it to point how im wanting it to. server { listen 80; server_name php.example.com; // <-I know i need to edit this, but not sure to what. access_log /var/log/nginx/localhost.access.log; root /usr/share/phpmyadmin; index index.php; location / { try_files $uri $uri/ @phpmyadmin; } location @phpmyadmin { fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME /usr/share/phpmyadmin/index.php; include /etc/nginx/fastcgi_params; fastcgi_param SCRIPT_NAME /index.php; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/phpmyadmin$fastcgi_script_name; include fastcgi_params; } }

Read the article
configuration of zend frame work in ubuntu

- by Rahul Mehta

Hi, I have created a project zfapi by zf command in ubuntu. Now http://myserverpath.com/zfapi/ gives me listing of folder public application and others. http://myserverpath.com/zfapi/public give me the index page index.php. and i have made the UserController.php in application/controllers but by http://myserverpath.com/zfapi/user/ is saying user not found. what configuration i need to set for running it proper. I had set my /etc/apache2/apache2.conf added the following in the last . <VirtualHost *:80> DocumentRoot "/var/www/mypath/zfapi" <Directory "/var/www/mypath/zfapi"> Order allow,deny Allow from all AllowOverride all </Directory> </VirtualHost> is giving me this error while restarting server. [Sat Jan 08 13:32:53 2011] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [Sat Jan 08 13:33:03 2011] [error] VirtualHost *:80 -- mixing * ports and non-* ports with a NameVirtualHost address is not supported, proceeding with undefined results what this i should do .?

Read the article
Connect to WEP Wireless Network by command line on Ubuntu

- by Tim

Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

Read the article
iptables configuration under ubuntu

- by aioobe

I'm following a tutorial on setting up a dns-tunnel. I've run into the following instruction: Now you need to enable forwarding on this server. I use iptables to implement masquerading. There are many HOWTOs about this (a simple one, for example). On Debian, the configuration file for iptables is in /var/lib/iptables/active. The relevant bit is: *nat :PREROUTING ACCEPT [6:1596] :POSTROUTING ACCEPT [1:76] :OUTPUT ACCEPT [1:76] -A POSTROUTING -s 10.0.0.0/8 -j MASQUERADE COMMIT Restart iptables: /etc/init.d/iptables restart The problem is that I don't have any /var/lib/iptables/active. (I'm on ubuntu.) How can I accomplish this? I suspect that I should just interact with the iptables command somehow but I have no clue what to write. Best would probably be if I could put the commands in a script somehow I suppose. (A side-note. If I execute a few iptables-commands it wont be there for ever, right? The rules will be discarded on reboot?)

Read the article
tab complete not working for vim in particular directory - ubuntu 12.04

- by user1160958

I am working on a ruby on rails app. All of the sudden the command line tab complete stopped working for vim, only for files though, and only for the vim command (i.e. works for other commands, ls, rm etc.) After further investigation - this only occurs in a specific directory, the home directory of my rails app. If I go into a sub directory in my rails app, or any other directory on my machine, the tab complete works again. If I go into the root directory of any other rails app, it works. I also tried renaming the diretory, and copying the contents of the directory to another directory, and that did not work either. It only does not work for files, and works for any other command - ls, rm etc. But when I do vim /path/to/file/, then tab to see a list of files in that directory, only other directories show, not files. I am using ubuntu 12.04. Also, I tried re-installing vim, re-booting, removing ~/.viminfo (there was no vimrc file) that didn't work. Any help would be appreciated!

Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121 | Next Page >