Search Results

Search found 16642 results on 666 pages for 'wireless security'.

Page 114/666 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

  • Hotspot is getting disconnected from other windows system?

    - by Gaurav_Java
    I created Hotspot for sharing my system internet for other system . but after 5 - 10 min my system internet is not able to share internet but it is connected with other windows system .windows showing (No internet access ) But after running this sudo killall dnsmasq windows is able to use internet connection not happening with one system same thing is happening with 2 -3 windows system . In many cases i have 2 restart my system Here My Hotspot setting

    Read the article

  • WiFi slow sometimes, reboot helps, how do I debug it?

    - by January
    Ubuntu 12.04.1 with all updates installed. Laptop Lenovo Thinkpad X230 with Intel Corporation Centrino Advanced-N 6205. WiFi sometimes becomes extremely slow. Often this occurs when I wake the system from suspend and connect to a different network. I find no obvious clues in system logs. /etc/init.d/network-manager restart doesn't help, but a reboot does. How can I go on with debugging this issue? In specific, which parts of the system should I try to restart (without a complete reboot)? I know of problems with Intel WiFi (see for example this question and the instructions here), but if that was the problem, I would expect the WiFi to be slow at all times, and not just sometimes. Also, I have a gut feeling that it might be a DNS issue (for example, getting a page from a known server is faster than accessing a new server), but I don't know how to tackle it. Update: despite numerous updates in the meanwhile, I still observe this behavior. It happens always when I access my WiFi router at home after returning from work; when I reboot my laptop, the connection speed is good again.

    Read the article

  • Ubuntu on Thinkpad Edge 11

    - by lasseespeholt
    Hi, I think a community wiki on problems (and solutions) when installing Ubuntu (10.10) on a Thinkpad Edge 11 would be nice (because I just got one ;)). I'll contribute with my own problems and solutions, and hope others will join too. Thinkwiki entry for the Edge 11 Known problems: No wifi-driver, solution: answer #1, answer #2 Fan is load, even though it's on auto. No solution. Thinkfan is a possible solution, but correction values for sensors should be supplied (mapping sensors to specific areas). Also, one sensor is between -100C and +100C - maybe some kind of deactivation would help.

    Read the article

  • Turning my mobile boardband into Wifi with my laptop using Kubuntu 12.04 to use it in my desktop PC

    - by Suhail cholassery
    Its been 3 or 4 months since I started using 12.04. What I want to do is very clear: Turn my mobile broadband connection into Wifi connection with my laptop using Kubuntu 12.04 to use it in my desktop PC. I browsed through most of the questions related to this (ad- hoc connections, bridging mobile broadband with Wifi, etc). I also read the ICS article, but I found those too difficult to digest. I hope that there is some other way to do this. I request you to give me a practical and applicable answer . I am not trying duplicate any other existing question.

    Read the article

  • Ubuntu Wifi Not Connecting (And keeps asking for authentication every minute or so)

    - by kelvinsong
    This is a problem in 12.10 that has been driving me nuts, and it's a problem with the wifi. Ubuntu will never connect to the network. All of my other devices work fine. What will happen is I will type in the password, the authentication window will go away, and the Wifi icon will pulsate for a while. Then about a minute later, a window will pop up asking for authentication to join the same wifi network. If you type in the password again it will do the same thing, and even if you hit [Cancel], the window will still pop back up in another minute. This is a very irritating thing.

    Read the article

  • no wifi after grub 2 crash

    - by Omu
    on ubuntu 10.10 I used StartupManager to set windows 7 as the default boot, also chosen the 1024x768 resolution, 16 bit, time: 3sec, and checked "show splash screen". after the restart there was no GRUB menu at all, windows 7 booted, and in windows the clock was 0:03 instead of 10:03, also the wifi doesn't sees any connections anymore I reinstalled ubuntu 10.10 so the GRUB menu is back, changed the clock back from BIOS, but my wifi doesn't sees any connections in windows nor in ubuntu (I write this from another computer)

    Read the article

  • Can't connect to or search Wi-Fi

    - by Mark
    I just installed the latest version of Ubuntu; I think it was 13 or something. Anyway, I got it running, and now I've been trying to connect to my Wi-Fi AP. No matter where I go I don't see an option for Wi-Fi. I looked on the computer and found some commands to use in a terminal to run a scan for Wi-Fi networks, but all of them returned the error: interface doesn't support scanning What are step-by-step directions to make this work?

    Read the article

  • Are the Ralink RT3090 drivers incompatible with Ubuntu 10.10?

    - by xd1936
    Ralink Technology publishes their drivers in source code form on their website here. When complied with make and make install in 10.04, the drivers worked well in 32 and 64 bit versions of Lucid. However, when compiled for the 64 bit version of Maverick, it does not work at all, and 32 bit Maverick, it works but randomly disconnects. Both versions of Maverick say "[Proprietary] Driver is activated but not in use" in the Proprietary Drivers dialog. Do the drivers just need to be updated? Is there an easy fix?

    Read the article

  • Realtek 8188ce stops working after 2minutes

    - by Max M
    I am using ubuntu 12.10 on an hp dm4-2191us via wubi with the Realtek 8188ce wifi adapter. Everything works very well with the exception of the wifi. I have used wicd and it didn't worked at all so i went back to Network Manager with variable success. It works for 30 min - 2 min before i have to reconnect to get it to work again. I would really like to use Ubuntu (it is a better platform in my opinion) but no wifi could really be a deal breaker.

    Read the article

  • Computer becomes unreachable on lan after some time

    - by Ashfame
    I work on my laptop and ssh into my desktop. I use a lot of key based authentication for many servers for work but recently I couldn't login because ssh would pick up and try all the keys and it stops trying before ultimately falling back to password based login. So right now I am using this command: ssh -X -o PubkeyAuthentication=no [email protected] #deskto The issue is after sometime the desktop would just become unreachable from laptop. I won't be able to open its localhost through IP and today I tried ping'in it and found a weird thing. Instead of 192.168.1.4, it tries to ping 192.168.1.3 which I am sure is the root cause as it just can't reach 192.168.1.4 when its actually trying for 192.168.1.3 Ping command output: ashfame@ashfame-xps:~$ ping 192.168.1.4 PING 192.168.1.4 (192.168.1.4) 56(84) bytes of data. From 192.168.1.3 icmp_seq=1 Destination Host Unreachable From 192.168.1.3 icmp_seq=2 Destination Host Unreachable From 192.168.1.3 icmp_seq=3 Destination Host Unreachable From 192.168.1.3 icmp_seq=4 Destination Host Unreachable From 192.168.1.3 icmp_seq=5 Destination Host Unreachable From 192.168.1.3 icmp_seq=6 Destination Host Unreachable From 192.168.1.3 icmp_seq=7 Destination Host Unreachable From 192.168.1.3 icmp_seq=8 Destination Host Unreachable From 192.168.1.3 icmp_seq=9 Destination Host Unreachable ^C --- 192.168.1.4 ping statistics --- 10 packets transmitted, 0 received, +9 errors, 100% packet loss, time 9047ms pipe 3 Also the ping command message comes in multiple and not one by one. (izx answer's the weirdness I thought there was in ping command.) I did check for desktop, its local IP is still the same, so something is going on in my laptop. Any ideas? P.S. - Laptop runs Ubuntu 12.04 & Desktop runs Ubuntu 11.10 Laptop is connected through wifi to router and Desktop is connected through LAN to router. Update: Even after setting up static IP leases in router settings, I again ran into this issue.

    Read the article

  • No wifi using Ubuntu on laptops

    - by Pete G
    I have loaded Ubuntu onto two different laptops and both had the same result...no WiFi. I could access the internet if I plugged into Ethernet port but try as I might, I just could not access WiFi. I even tried Wine to install a Windows based external usb WiFi device but again...nothing. It functioned normally in Windows but with Ubuntu installed....nothing and this was the same whether it installed just Ubuntu or dual booted with Windows. Any suggestions? Thx!

    Read the article

  • networkprinting with cups in ubuntu 13.10

    - by gero
    I upgraded from Ubuntu 13.04 to Ubuntu 13.10. The printer configurations were transferred correctly. I have an USB laser printer, which still works if I connect my laptop directly. Usually I used this printer by wlan or bluetooth, where an old laptop works as server (cups 1.3.X). If I now want to print some pdf or postscript file, one or the other way I only obtain a header printed, not the content of the file. Curiously the Ubuntu 13.10 test page is printed correctly.

    Read the article

  • Putting Ubuntu Server on to a networked HDD

    - by SimplySimon
    Firstly, I know very little about servers and secondly the 1Tb HDD I have has network capabilities, but no software is installed on it, so when connected to the computer it is seen as a network connection, but not as a drive. Any advice on how to get started would be great. Up until now, I have been using it as a USB drive which worked well, but when this is sorted, I would like it to be connected directly to our BT HomeHub accessible through the WiFi for all the family to use as a film and back up repository. I would then be able to set up individual accounts for each family member to use and may be, if possible, make it accessible from outside locations. The First question then is: How can I install Ubuntu server on the 1Tb HDD attached directly to the computers network port but which doesn't show up in Nautilus? HDD Western Digital 1.0Tb LBA 1953525168 Model: WD10EACS-00DB0 DCM: DHRNHT2CF

    Read the article

  • HP DV6 connects but no internet

    - by Frank Barcenas
    I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

    Read the article

  • Wifi won't connect to certain networks

    - by Dave M G
    As I write this, I'm in a coffee shop on my laptop, and I am trying to connect to the free wifi network they offer. Every time I select their network from the wifi applet drop down menu, it connects for a second and then disconnects. At the same time, I have my Android phone with me, and it connects to the coffee shop's network without problem. There are a couple of people around me also using the same network with no issues. I asked the staff to check and as far as they can tell there is no problem with their router or anything. I have tried rebooting, but it has not made a difference. I have double and triple checked that I am using the correct WEP password. As an added wrinkle, when I connect to another network, it seems to connect (although I can't use them because they are paid gateway services). So I'm able to ask this question now because I have tethered my laptop to my phone, but it's slow and a workaround, not a solution. All indications are that it's a problem with my computer against this one network. Why would that be and how can I fix it?

    Read the article

  • Need in obtaining a specific local telephone number [closed]

    - by Brett
    I am wanting a local phone number that I like. I have found one that I like. When I call the number that I want it says "this number has not been allocated" I have looked up and found the company that owns that number. How do I go about acquiring that number from the company. I spoke with someone who sells major phone packages and he said that if I signed up with them he could get the number for me. He said that there is a change of ownership form that the send to get the number. So I know it can be done. I am hoping that someone with industry specific knowledge in this area can guide me in getting this number.

    Read the article

  • Ubuntu 12.10 WiFi Problems

    - by Sean Webber
    I have a 32 bit machine running Ubuntu 12.10 with WiFi on it. I have a WPA2 network at home, but if I leave the USB Adapter plugged in while it boots, it infinitely keeps asking for the network password but never connects. If I plug it in after boot, it will connect but then I can't access ANYTHING on the LAN or Internet because "the DNS servers are unreachable". Now, if I leave the computer on a while, I get lucky sometimes and it MAGICALLY decides to connect for a little bit, lock the machine though and the Internet's gone again. The weirdest thing, is when I am connected but can't get to the internet, I do a netstat or ifconfig wlan0, I do have an IP address and everything. It says I'm connected but its not. I have a Realtek RTL8188CU USB adapter.

    Read the article

  • Can't connect to windows 7 ad-hoc network

    - by Nikolaj
    Good day! I have installed ubuntu 12.04 on my laptop and I need to have network connection on it. Have a desktop PC, where I've created ad-hoc wi-fi network(Windows 7) and can't connect to it. So, problem: I see my network in the list of networks to connect, but I cant connect to it because it's grey color and not active(can't click on it). Could somebody help me to solve that problem? Thanks in advance!

    Read the article

  • Wifi stops working in 13.10

    - by Vitor
    OK, my wifi is connecting fine, but it just stop downloading and uploading data. The skype stops, trying to reconnect, the firefox nighly and the google chromium stops loading pages and websites, everythings stops. But when I see the network icon: connected to my wifi. Then, I simply reconnect, or disconnect and connect again. Reconnecting, the wifi starts working again, the skype icon turns green, the browsers work again. Previously, I had 13.04 and never had this problem. When I upgraded to Ubuntu 13.10, the wifi started to do this. And the wifi has this problem since the early times of 13.10; since I installed 13.10, the wifi is having this issue (from the first day I installed it). Anyone having the same problem? Anyone knows how to fix it?

    Read the article

  • 3G dongle and memory card detection

    - by user212632
    My questions is about 3G dongle (Huawei E1752) that I use for my internet on Ubuntu 12.04. The big issue is that ubuntu only recognise the dongle if I plug it in before booting up. But if somehow I loses connection (due to network being low) then the only way to use the 3G dongle again is to reboot my machine, which becomes a pain. I have the same issue with the memory card reader of my laptop whereby it only reads when I insert the card before booting up. My laptop is an Acer V3 -571g. At first I thought it was an issue that the model was quite new, but I have been updating my ubuntu for a while, and this issue has kept being the same

    Read the article

  • Is it possible to configure Apple's Magic Mouse to be recognised on start up?

    - by Dave
    This question may apply more roundly to all bluetooth mice but in my case I am dealing with an Apple Magic Mouse. I have followed the set up instructions here; https://wiki.ubuntu.com/Multitouch/AppleMagicMouse closely. I have even removed the mouse and started from scratch more than once repeating each step described carefully. Every time the computer is started it does not see the Magic Mouse by default. I need to keep a wired mouse connected to the computer at all times which I use to log in with then connect the Magic Mouse, in a somewhat counter-intuitive exercise! Any help would be greatly appreciated.

    Read the article

  • How to connect MTS MBlaze

    - by murali_ma
    i have installed ubuntu 11.04 inside the windows xp. i have MTS Mblaze USB Modem. (my service provider is MTS MBlaze,india) i want to use Mblaze into ubuntu so that i did the following steps for make connecting the device. from the task bar->edit connections->mobile broadband->choose country->mts mblaze and ok i give username and password ([email protected] and password MTS. ok now i enable mobile broadband , MTS MBlaze connection1(connection name) from task bar. steps followed from "http://randomshandom.wordpress.com/2010/12/20/how-to-connect-mts-mblaze-device-in-ubuntu-10-10-11-04/#more-3" for the first time it successfully connected and browse the internet. after i restart the system i connect it. it does not connected. it shows Modem network disconnected. i accessed many times and delete the connection and recreated but i does not help me. if i try to connect device i think it the search the network, i saw the wave signal. img Image for showing problem:

    Read the article

  • WiFi, No ping, other works fine

    - by Linux Mom
    I installed Ubuntu 12.04 LTS for my mom, this runs OK. However recently, I switched back and forth between encryptions on our WiFi Router from WPA-PSK to WEP and back again to WPA-PSK, same password. Now this old laptop won't even ping the gateway on the router, although the nm-applet shows connected. I tried re-adding the network and putting in the BSSID. I did this over again sometimes just to verify. I tried with my 3G Tethering on my phone, it works fine, can go online too. My other Linux laptop can go on the same wifi as well as my phone. And this laptop used to been online on the same network, same password, same encryption (WPA-PSK) What can be wrong ? Does it need a serious kick in the butt or removing some cached authorisation somewhere?

    Read the article

  • Installing driver for Ralink Realtek 8187 WiFi adapter

    - by capcom
    I purchased a WiFi adapter online, and it came with an installation CD with drivers. I installed it just fine on Windows, and am now trying on Ubuntu 10.10. The CD came with the driver files for Linux as well, but I have no idea why they aren't working - my guess is that I don't properly understand what to do with them. I have uploaded the contents of the folder which came with the CD here. There is a README in there, but the instructions under the installation header didn't get me anywhere unfortunately. The Device ID is: Bus 001 Device 002: ID 148f:5370 Ralink Technology, Corp. Thanks.

    Read the article

  • huwai 1731 ( mobile broadband ) not working with dell inspiron 3521

    - by N.Ramkumar
    Please help, one of my friend shared this note ( enclosed below), I used these codes and my laptop is able open the data card but I am not getting any signals. I am able to work with wired connection, but wi-fi and mobile broad band are not working. Please help. sudo apt-get purge usb-modeswitch sudo apt-get update sudo spt-get install usb-modeswitch sudo apt-get update gksudo gedit /lib/udev/rules.d/40-usb_modeswitch.rules Once you enter these above commands 40-usb_modeswitch.rules text file will open. Then, copy below mentioned lines into 40-usb_modeswitch.rules text file. #Huawei E1731 ATTRS{idVendor}=="12d1", ATTRS{idProduct}=="1446", RUN+="usb_modeswitch '%b/%k'" Save the file Then type : sudo apt-get update Then restart the machine.

    Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >