Search Results

Search found 3324 results on 133 pages for 'gb j'.

Page 115/133 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• Graphics Artifacts/ Texture Flickering

  - by Cerin

  Hey I been having some problems with artifacts in games. Sometimes textures flicker. Artifacts of various shapes and sizes show up usually after a couple games of dota 2. I built my computer almost exactly one month ago and it has been doing this pretty much from the start except before the artifacts I believe just flashed on screen fast enough to where I couldn't tell what it was but I still noticed. In dota I've seen green triangular artifacts among other things. I've tried running Furmark for a while but even though it pushes the gpu much harder than dota 2, there are still no artifacts. It maxes in furmark at about 60C and running every game I've tried on it at 40C. CPU and system temp don't usually get higher than 40C either. These are my system specs: Gigabyte Z68 Intel Motherboard 16 GB Gskill Ripjaws SDRAM DDR3 Sapphire Radeon HD 7770 GHz edition Intel Core i5-2500k (with built in gpu) Corsair 750 Watt PSU windows 7-64 bit I have the latest drivers for everything. What should I do about this? Try to RMA my graphics card? Are there other things that could be causing this?

  Read the article

• Unable to connect to Windows VPN from iPad

  - by Justin

  I have a 16 GB iPad wifi I can't get to connect to VPN. The error I get is: "A connection could not be established to the PP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator." I have tried a variety of tasks to troubleshoot the issue: I have verified that another iPad on another network can connect to the VPN I am trying to connect to I can connect to this VPN from the same network the iPad uses on a Windows machine I have verified an iPhone user can connect to this VPN from a different network I have reset the iPad's network settings I have reset the entire iPad and restored settings I have compared my settings w/ a screenshot from the iPad that works and confirmed everything is correct I have used the IP address and domain name of our VPN server in the settings I have tried deleting the VPN settings in the iPad and recreating them I have verified in the logs of VPN server that I'm not even getting to the VPN server (no log entry) I have verified that I cannot VPN from the iPad on separate network (different ISP and router) Are there any other ways to troubleshoot VPN on an iPad?

  Read the article

• What to look for in a switch with LAN/WAN verses an iSCSI SAN?

  - by Luke

  I'm setting up a VMWare ESXi 5 environment with 3 server nodes. Dell recommended 2x Force10 S60 switches shared (iSCSI SAN, LAN/WAN). The S60 switches are extremely powerful. They have 1.25 GB of buffer cache, < 9us latency. But they are very expensive (online price ~$15k per switch, actual quote a little less). I've been told that "by the book" you should at least have 2 internal switches for SAN, and 2 switches for LAN/WAN (each with a redundant). I know some of the pros and cons of each approach. What I'm wondering is, would it be more cost effective to disjoin the SAN from LAN with less expensive switches? The answer to this question highlights what I should be looking for in a switch for the SAN. What should I be looking for in a LAN/WAN switch, in comparison to the SAN? With the above linked question for the SAN: How is buffer latency measured? When you see 36 MB of buffer cache, is that shared or per port? So 36 MB would be 768kb or 36MB per port? With 3 to 6 servers how much buffer cache do you really need? What else should I be looking at? Our application will be heavily using HTML5 websockets (high number of persistent connections). The amount of data being sent is small; Data sent between client <- server isn't broadcasted (not a chat/IM service). We will be doing some database reporting too (csv export, sums, some joins). We are a small business and on a budget. We'd probably only be able to spend no more than $20k on switches total (2 or 4).

  Read the article

• Reduce "Metafile" memory usage?

  - by Jay Conrod

  My work computer (Windows 7 64-bit) spends a lot of time swapping memory when I switch between programs. This surprises me since I have 4 GB of RAM, and the programs I use aren't particularly RAM hungry (Outlook, Emacs, p4win, Firefox, various build tools). I downloaded RAMMap, and it shows over a gigabyte of memory used by "Metafile". From the Sysinternals blog: Metafile is part of the system cache and consists of NTFS metadata. NTFS metadata includes the MFT as well as the other various NTFS metadata files. ... In the MFT each file attribute record takes 1k and each file has at least one attribute record. Add to this the other NTFS metadata files and you can see why the Metafile category can grow quite large on servers with lots of files. So I understand what the "Metafile" data is... I work on large builds comprising hundreds of thousands of files (none are that big, but they add up to several gigabytes). My question is how can I reduce the amount of memory used by "Metafile"? I'm not actively using all those files at once, so why does Windows need to keep info in RAM? Restarting my machine every time I sync a new build is really annoying.

  Read the article

• sudo fdisk in a live session does not show all hard drives

  - by cornbread

  I am having Grub2 issues in my Ubuntu 10.04 dual boot, 2 hard drive system. So I am attempting to follow the standard grub2 reinstallation guide (cant post link because of spam filters allowing only one... ?_?) Don't know if this is the root of my problem, but my speedy internal HD with my OS on it is not showing up anywhere in a live session. Not in nautilus, behind fdisk.... no where. When I can get the main system to boot, there is no issue seeing all available partitions. But the live session sees only the 1TB internal media/backup hard drive. I need access to the other hard drive and it's partitions to finish the grub2 re-installation but I am not sure anymore that is the underlying issue. Anyone have experience with this? The issue I have identified as a grub2 issue is fully described here. SandPvvr describes it exactly. Some notes: I do not see the grub2 menu for my os's holding down the shift key after my bios screen works maybe 10% of the time Not related to reinstalling a windows os. havent been touched in a year do some web development. issue may have started when I was playing with ruby and django. not sure on this. Could a dev environment do this? fdisk in live session ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0001d518 Device Boot Start End Blocks Id System /dev/sdb2 1 121601 976759939 5 Extended /dev/sdb5 487 110765 885816036 83 Linux /dev/sdb6 110766 121601 87040138+ b W95 FAT32 /dev/sdb7 1 486 3903700+ 82 Linux swap / Solaris Partition table entries are not in disk order

  Read the article

• Reducing both pagfile.sys and hiberfil.sys in Windows 7

  - by greenber

  I recently used Defraggler to consolidate my free space areas on my D: drive preparatory to using Disk Manager to break my drive into two areas, one as my "data area" for Windows 7 (normally on my C: drive) and to experiment around with Windows 8. The Defraggler program works so well I ran it on my C: drive and I ended up with a lot of free space both on my C: drive and my D: drive. I was very happy. And then I woke up the next day and I've got virtually no free space left, something like 8 MB on my C: drive and about 3 GB on my D: drive. I then ran Wintree (which gives a nifty graphical representation of disk usage) and found I had a large page file and a large hiberfil. So I temporarily turned off hibernate and reduced the page file size to 2000megabytes and then rebooted so that both would take effect. It had no effect on the C: drive or the D: drive. That makes no sense to me. What caused the free space on each drive to disappear, why doesn't the page file size being reduced and the hibernate file being turned off free up disk space to either the C: or the D: drive? Would it make sense to delete the two files in question and, if so, how do I go about doing that? Safe mode? Thanks. Ross

  Read the article

• Intermittent Trouble Entering Hibernate on WinXP

  - by kquinn

  My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

  Read the article

• Servers / ram for social network- how many?

  - by Marty

  I am launching my social network soon an looking into hosting. The question i am lost is: Do i need separate servers for web vs database vs image handling since there is photo sharing? Or does 1 server handle it all? Also is more ram better? If i get 50GB ram is that better than having 8 gb ram? EDIT: It is PHP codeignitor and MySQL for now. (switch to NoSQL DB later if demand calls fr it.) I will be using memcache also. Concept wise it is similar to yelp, so geographic based with lots of user content and image sharing + live feeds an privacy levels. User plan is open question. Without testing the demand for this i cant give a number. But the concept is unique, no one out there with the set of features i am releasing so it could grow. Ideally I want to plan for handling about 1-2 million views / month from launch. If it goes more than that then I will upgrade.

  Read the article

• Messed up partitions... system will not boot!

  - by someguy

  I did a really dumb thing. cfdisk threw an error at me saying "FATAL ERROR: Bad primary partition 3: Partition ends in the final partial cylinder", so I installed Partition Table Doctor to see if I could fix the problem. When the program started up, it told me there were problems with my partitions, and asked if I wanted them fixed (cannot remember real message, but I believe it had something to do with the cylinder boundaries), so, blindly, without thinking of the consequences, I did. Now, my system will not boot. I tried booting from the Windows 7 installation CD. I went to install a fresh copy, but it said that "No drives were found". I then opened up diskpart. According to diskpart, there is only one partition, containing one volume, assigned the letter "C". Before, I had four partitions! It is also saying that the file system is RAW. Is there any way I can fix this? I have important data that I do not want to lose. Later on... I tried fdisk with the option -l, which lists the partition table(s), and this is what I got: Ignoring extra extended partition 4 Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 64 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x163df116 Device Boot Start End Blocks Id System /dev/sda1 6 18 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 18 7851 62918572+ 7 HPFS/NTFS /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30402 139196416 f W95 Ext'd (LBA) /dev/sda3 13073 30403 139203193 7 HPFS/NTFS I don't know if this will help, but it's extra information, at least. Also, this is how I had my partitions: 40MB (Unallocated) 100MB (System Reserved) 60GB (Windows, C:) 40GB (Was reserved for secondary OS) ~132GB (Home, E:)

  Read the article

• Move OS from RAID5 array to RAID 1 arrays

  - by Antoine

  I want to give a last boost to my old ProLiant ML350 G5 server which just needs to be reliable for a few more year only ! With a defined budget of about 1500$ (I do not have more), i plan to replace the CPU (+ adding a second one), the battery cache of my raid controller (E200i), double the RAM, and change all hard drives. I have 7 HDD (SAS 10krpm, 72Gb) + 1 spare in RAID5, and my system is all FULL (no empty tray, full disks). in my current RAID5 array, I have 2 partitions: - 1 OS partition, 20Gb - 1 data partition, 350 Gb I plan to replace these 8 disks with : - 2 x 300Gb SAS 15krpm in RAID 1 (= 1 partition for OS) - 2 x 2Tb SATA 7.2krpm in RAID 1 (= 1 partition for DATA) My biggest constraint is that I have only 01 day to upgrade my server. Therefore, I'm looking for cloning all my files (OS + data partition) to my new arrays, i.e : - the OS partition shall be cloned to the RAID1 "2x300Gb array" - the data partition shall be cloned to the RAID1 "2x2Tb array" My second problem is that I need to physically remove all the old hard drives before inserting the new ones. I'm running Windows Server 2003 R2, and even if MS support will expire soon, I cannot buy a new licence and spent time in configuration. Obviously, with 1500$, I cannot also buy a new server that I could start configuring from now ! Thought about ASR (NTBackup), but I have no floppy drive (and do not really want to invest in one !) Thought about a clonezilla clone, and read this interesting link : Windows Server 2003 - move C: partition to a new SAS disk , but i'm not so confident in using Clonezilla with RAID5. What should be the best option to quickly and easily (if possible!) "copy/paste" my OS (so no need to reinstall and reconfigure all) and DATA / programs / services, etc... ? Thanks for your comments

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

• Why is IIS 7.5 seeing some requests as HTTP/1.0?

  - by Zhaph - Ben Duguid

  While trying to work out why Static File Compression wasn't working on one of our IIS servers, the error was coming back as "NO_COMPRESSION_10" which translates to: Server not configured to compress 1.0 requests Looking at the requests in Fiddler, I can see that I'm requesting HTTP 1.1, but everything is being sent back as HTTP 1.0: Request (from chrome, captured via Fiddler): GET /css/reset.css HTTP/1.1 Host: [-----].com Connection: keep-alive Cache-Control: max-age=0 If-Modified-Since: Tue, 16 Oct 2012 15:04:34 GMT User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11 Accept: text/css,*/*;q=0.1 Referer: http://[-----].com/ Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en;q=0.8,en-US;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Response from IIS: HTTP/1.0 200 OK Cache-Control: no-cache, no-store Pragma: no-cache Content-Type: text/html; charset=utf-8 Expires: -1 Server: Microsoft-IIS/7.5 X-AspNet-Version: 4.0.30319 X-Powered-By: ASP.NET Date: Tue, 11 Dec 2012 11:57:03 GMT Connection: close Content-Length: 108837 Other servers with the same host that I'm running this site on all respond with HTTP/1.1. How can I persuade IIS to respond with HTTP/1.1 rather than HTTP/1.0? Edit to add: Digging deeper, I can see that some responses from the server are indeed being returned compressed, so I guess really I'm trying to work out why talking to this particular server from our office seems to result in it seeing 1.0 requests, while other servers at the same co-loc don't?

  Read the article

• Corrupted NTFS Drive showing multiple unallocated partitions

  - by volting

  My external hdd with a single NTFS partition was accidentaly plugged out (kids!)... and is now corrupted. Iv tried running ntfsfix - with no luck - output below.. When I look at the disk under disk management in Windows 7 it shows up as having 5 partitions 2 of which are unallocated - none have drive letters and it is not possible to set any (that option and most others are greyed out) - so I can't run chkdsk /f Iv tried using Minitool partition wizard which was mentioned as a solution to another similar question here. It showed the whole drive as one partition, but as unallocated, and the option -- "Check File System" was greyout. Is there anything else I could try ? Output of fdisk -l Disk /dev/sdb: 1500.3 GB, 1500299395072 bytes 255 heads, 63 sectors/track, 182401 cylinders, total 2930272256 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytest I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x69205244 This doesn't look like a partition table Probably you selected the wrong device. Device Boot Start End Blocks Id System /dev/sdb1 ? 218129509 1920119918 850995205 72 Unknown /dev/sdb2 ? 729050177 1273024900 271987362 74 Unknown /dev/sdb3 ? 168653938 168653938 0 65 Novell Netware 386 /dev/sdb4 2692939776 2692991410 25817+ 0 Empty Partition table entries are not in disk order Output of ntfsfix me@vaio:/dev$ sudo ntfsfix /dev/sdb Mounting volume... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Attempting to correct errors... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error FAILED Failed to startup volume: Input/output error Checking for self-located MFT segment... ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument OK ntfs_mst_post_read_fixup_warn: magic: 0xffffffff size: 1024 usa_ofs: 65535 usa_count: 65534: Invalid argument Record 0 has no FILE magic (0xffffffff) Failed to load $MFT: Input/output error Volume is corrupt. You should run chkdsk. Options available with MiniTool: Related questions: How to fix a damaged/corrupted NTFS filesystem/partition without losing the data on it? Repair corrupted NTFS File System

  Read the article

• Missing drive space in Server 2003

  - by Tim Brigham

  I have two drives used for SQL backups which for the last week have been acting strange - the free space indicated by windows is far off from what windirstat, etc indicates. There should only be about 60 GB of drive space used and there is about 160. This would match the utilization if the two last backup files were still residing on disk. SQL server is 2000, OS Server 2003 x64. Running on a VMware 5.0 cluster. OSSEC and McAfee for this system shows clean. My current plan is to temporarily attach one of these drives this drive to another VM for analysis. Is there anything more I should be looking at? There were a lot of pages on the net when I was looking for documentation on this issue but I haven't found this case described. EDIT: Unfortunately even a full reboot did not clear this behavior. I also used process explorer to look for open file handles. No dice.

  Read the article

• Ubuntu network card problem.

  - by Steve Greene

  Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, it works fine under Windows Vista. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System.

  Read the article

• Multiple servers vs 1 big server performace

  - by pistacchio

  Hi to all! My team of developers has suggested a server structure for an upcoming project we are developing. Our structure is "logical", meaning that the various logical components of the application (it is a distributed one) relies on different servers. Some components are more critical than others and will be subjected to more load. Our proposal was to have 1 server per component but the hardware guys suggested to replace the various machines with a single, bigger one with virtual servers. They're gonna use Blade Servers. Now, I'm not an expert at all, but my question to the guys was: so if we need, for example, 3 2GHz CPU / 2GB RAM machines and you give me 1 machine with 3 2GHz CPUs and 6 GB of RAM it is the same? They told me it is. Is this accurate? What are the advantages or disadvantages of both the solutions? What are the generally accepted best practices? Could you point out some URL reference dealing with the problem? Thank you in advance! EDIT: Some more info. The (internet / intranet) application is already layered. We have some servers on the DMZ that will expose pages to the internet and the databases are on their own machines. What we want to split (and they want to join) are some webservers that mainly expose webservices. One is a DAL that communicates with the database layer, one is our Single Sign On / User Profile application that gets called once per page and one is a clone of what seen on the Internet to be used on our lan.

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• Solution to easily share large files with non-tech-savvy users?

  - by Tim

  Hey all, We've got a server setup at work which we'd like to use to exchange large files with known clients easily. We're looking into software to facilitate this, but somewhow typing "large file hosting" into Google gives questionable results.. ;) We've come up with the following requirements, and I hope any of you can points us in the direction of a solution that offers this functionality, or is malleable to our needs. Synchronization / revision management is of no concern, it's mostly single large (up to 1+ GB) file uploads & downloads we'll need. We'd like to make the downloads expire & be removed after a certain number of days / downloads, to limit the amount of cleanup we'd have to do. The data files exchanged sometimes hold confidential information, so the URLs generated should be random and not publicly visible. Our users are of the less technically savvy variety, so a simple webform would be best over a desktop client (because we also have to support a mix of operating systems). As for use of the system we'd either like to send out generated random URLs for them to upload their files, or have an easy way manage & expire users. Works on a linux (Ubuntu) server (so nothing .Net-related please) Does anyone know of software that fits the above criteria? We've already seen a few instances of this within the scientific community, but nothing we could use directly.. Best regards, Tim

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• rpmbuild gives seg fault

  - by Deepti Jain

  I am trying to build an rpm using the rpmbuild tool. I have source code which build binaries around 30 GB. This software for which I am making the rpm has dozens of executables. When I copy only the binaries of a single executable (Eg. init) my rpm builds successfully. But when I dump the entire build to the rpm, rpmbuild does everything but gives a seg fault in the end. Here is my spec file: # This is a sample spec file for wget %define _topdir /root/mywget %define name source %define release 1 %define version 1.12 %define _builddir /root/mywget/BUILD/glenlivet %define _buildrootdir /root/mywget/BUILDROOT %define _buildroot /root/mywget/BUILDROOT %define _sourcedir /root/mywget/SOURCES BuildRoot: %{_buildroot} Summary: GNU source License: GPL Name: %{name} Version: %{version} Release: %{release} Source: %{name}-%{version}.tar.gz Prefix: /usr Group: Development/Tools %description The GNU sample program downloads files from the Internet using the command-line. %prep %setup -q -n glenlivet %build cd %{_builddir} make all %install rm -rf %{_buildrootdir} mkdir -p %{_buildrootdir}/bin cp -p -r %{_builddir}/build/obj-x64/* %{_buildrootdir}/bin/ %files %defattr(-,root,root) /bin/* If I only copy some of the binaries (let say one utility and its dependent binaries) it works fine. But when I try to copy the entire build, I get a seg fault. I get the seg fault after rpmbuild has executed these sections: %prep %build %install rpmbuild also processes my source file. Processing files: source-1.12-1 Finding Provides: Finding Requires: Finding Supplements: Provides:...... Requires:...... Checking for unpackaged file(s):/ usr/lib/rpm/check-files /root/mywget/BUILDROOT Checking for unpackaged file(s):/ usr/lib/rpm/check-files /root/mywget/BUILDROOT Segmentation fault Any clue what wrong is going on or where does rpmbuild fails? Thanks in advance

  Read the article

• dd on entire disk, but do not want empty portion

  - by Jonathan Henson

  I have a disk, say /dev/sda. Here is fdisk -l: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0000e4b5 Device Boot Start End Blocks Id System /dev/sda1 * 1 27 209920 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 27 525 4000768 5 Extended Partition 2 does not end on cylinder boundary. /dev/sda5 27 353 2621440 83 Linux /dev/sda6 353 405 416768 83 Linux /dev/sda7 405 490 675840 83 Linux /dev/sda8 490 525 282624 83 Linux I need to make an image to store on our file server for use in flashing other devices we are manufacturing so I only want the used space (only about 4gb). I want to keep the mbr etc... as this device should be boot ready as soon as the copy is finished. Any ideas? I previously had been using dd if=/dev/sda of=[//fileserver/file], but at that time, my master copy was on a 4gb flash ide.

  Read the article

• How to migrate WinXP from failing old HD to new one

  - by Péter Török

  Following this issue, we have all our important data backed up now. I also bought and installed a new replacement hard disk (WD 160GB PATA) as secondary (slave) drive. I created two primary NTFS partitions on it: a 40 GB system partition, and a 110GB data partition. In theory I could start reinstalling WinXP from scratch on the new system partition, then copying over all user data from the old drive to the new data partition. Once this is done, I could even throw away the old drive, or keep it just to see what happens. (Note: I don't want to clone the whole drive as it contains a dual boot setup with an old Linux installation which I don't need anymore, and anyway, a fresh reinstall would do WinXP good to get rid of many years' clutter.) However, I am lazy :-) The old HD is still functioning, the problem has not manifested again since. So I feel there is no need to hurry with a complete OS reinstall. What I don't know though is whether I will be able to install WinXP on the new system partition at a later stage without affecting the contents of the data partition on the same drive. If this is possible, I can just move over all our data to the new data partition to have it safe, then continue running WinXP from the old drive as long as it works. Does anyone see any problems/risks with this plan?

  Read the article

• Troubleshooting an overheating CPU

  - by Jeff Fry

  I & my father just recently put together a new PC. Specs below. From the very beginning, on boot it will often complain that the CPU is too hot. If I sit in BIOS and watch the CPU, it'll drop back down from red to blue (<72C), at which point I've tended to just boot into Windows...and haven't had any problems. In fact, I've played a couple hours straight of Skyrim at max settings, and not had any visible issues. That said, I've occasionally walked away & come back to find that it's crashed. Yesterday, it crashed (while idle) twice in 12 hours, which shifted the balance from busy-with-life to nervous-I'm-about-to-melt-something. I just installed Core Temp which is showing my 4 cores fluxuating between 70-98C. I'm guessing at this point that the CPU fan may be incorrectly installed or defective. My first thought is to either (a) add water cooling (which the case supports) and / or (b) replace the CPU fan with an after-market one. That said, I'm very open to suggestions. A note, while I certainly don't want to burn money here, I have a baby coming any day now and am still unpacking from a recent move so if I have a choice between an option that costs money and another that takes a while...I'll happily spend a bit extra. Side question: Should I be nervous to even have this on at this point? Let me know if there's something useful I could add to my report. Otherwise, I'm looking forward to your suggestions! Thanks. CPU Intel i7-2600 CPU w/ stock fan Other HW ASUS P8Z68-V Pro motherboard 64G SSD boot drive 4 older SATA HDs GIGABYTE ATI Radeon HD6950 1 GB DDR5 8G Kingston T1 Series RAM Corsair 650W Gold Certified power supply Antec P280 case

  Read the article

• Computer crashes if left unattended AND running uTorrent, what could be?

  - by DiegoDD

  I have a weird problem in which, if I leave my computer unattended, AND I leave uTorrent open, downloading/seeding, the computer simply crashes after about 20 / 30 minutes (don't know exactly since if I leave it, and come back later, it has already restarted or has a BSOD.) If I leave the computer alone for undefined time WITHOUT uTorrent, nothing happens, and if I am constantly using the computer while using uTorrent, no problem either (I could be using it all day with uT open and it doesn't crash). So what could it be that the combination of those cases makes the computer crash? I have already checked the power management so the computer never enters stand by mode, sleep, hibernate, etc. (the only thing I do is turn off the display). A first guess is that maybe one of my external hard drives DO sleep or enters in a "low power" mode or something if I don't use the PC. but since uT is running MAYBE tries to use that drive, and makes it crash. Could that be possible? How to know for sure if the external drive does that, and to prevent it from doing so. Any more ideas of what may be causing that? Specs: Windows 7 Pro, 64-bit, 2 GB RAM. Latest version of uTorrent (although it has been happening for a while now). UPDATE: i just found out that uTorrent has Disk cache options ( preferences - advanced - disk cache ). I have no idea if that may be causing problems with my external drive, hence causing the crash.

  Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >