Search Results

Search found 11093 results on 444 pages for 'issues'.

Page 115/444 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

  • Juniper not working on Windows 8.1

    - by MikePR
    I recently upgrade my laptop to windows 8.1 and now I can't run the Juniper terminal to connect to the company VPN. At the moment to click on the virtual machine it launche the terminal and afetr a few seconds a messages popup appears saying: juniper terminal services client has stopped working When I had windows 8 I was able to run Juniper without any problem. But in Windows 8.1 seems there are compatibilities issues. Any suggestion, solution or workaround? Thanks in advance

    Read the article

  • Determining the health of a Cisco switch port?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced recently, however, the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link. We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Linux: Case-INSENSITIVE Filesystem

    - by Quandary
    What methods are there to make the Linux filesystem case-INSENSITIVE ? I have asp.net applications developed on Windows, but there are always issues with capitalization/spelling on mono when putting it on Linux. One way is to mount a localhost SMB share to /var/www. Are there any others ?

    Read the article

  • ltsp-built-client error

    - by sat
    I am facing some issues while building a thin client using the ltsp-build-client, it says an error. Error is: I: Retrieving Release E: Failed getting release file file://root/ISO/ubuntu-12.04.1-desktop-i386.iso/dists/squeeze/Release error: LTSP client installation ended abnormally My Command is: ltsp-build-client --mirror file://root/ISO/ubuntu-12.04.1-desktop-i386.iso --security-mirror none --accept-unsigned-packages I am referring this URL http://wiki.debian.org/LTSP/Howto. How to solve this error?

    Read the article

  • Is post-sudden-power-loss filesystem corruption on an SSD drive's ext3 partition "expected behavior"?

    - by Jeremy Friesner
    My company makes an embedded Debian Linux device that boots from an ext3 partition on an internal SSD drive. Because the device is an embedded "black box", it is usually shut down the rude way, by simply cutting power to the device via an external switch. This is normally okay, as ext3's journalling keeps things in order, so other than the occasional loss of part of a log file, things keep chugging along fine. However, we've recently seen a number of units where after a number of hard-power-cycles the ext3 partition starts to develop structural issues -- in particular, we run e2fsck on the ext3 partition and it finds a number of issues like those shown in the output listing at the bottom of this Question. Running e2fsck until it stops reporting errors (or reformatting the partition) clears the issues. My question is... what are the implications of seeing problems like this on an ext3/SSD system that has been subjected to lots of sudden/unexpected shutdowns? My feeling is that this might be a sign of a software or hardware problem in our system, since my understanding is that (barring a bug or hardware problem) ext3's journalling feature is supposed to prevent these sorts of filesystem-integrity errors. (Note: I understand that user-data is not journalled and so munged/missing/truncated user-files can happen; I'm specifically talking here about filesystem-metadata errors like those shown below) My co-worker, on the other hand, says that this is known/expected behavior because SSD controllers sometimes re-order write commands and that can cause the ext3 journal to get confused. In particular, he believes that even given normally functioning hardware and bug-free software, the ext3 journal only makes filesystem corruption less likely, not impossible, so we should not be surprised to see problems like this from time to time. Which of us is right? Embedded-PC-failsafe:~# ls Embedded-PC-failsafe:~# umount /mnt/unionfs Embedded-PC-failsafe:~# e2fsck /dev/sda3 e2fsck 1.41.3 (12-Oct-2008) embeddedrootwrite contains a file system with errors, check forced. Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Invalid inode number for '.' in directory inode 46948. Fix<y>? yes Directory inode 46948, block 0, offset 12: directory corrupted Salvage<y>? yes Entry 'status_2012-11-26_14h13m41.csv' in /var/log/status_logs (46956) has deleted/unused inode 47075. Clear<y>? yes Entry 'status_2012-11-26_10h42m58.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47076. Clear<y>? yes Entry 'status_2012-11-26_11h29m41.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47080. Clear<y>? yes Entry 'status_2012-11-26_11h42m13.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47081. Clear<y>? yes Entry 'status_2012-11-26_12h07m17.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47083. Clear<y>? yes Entry 'status_2012-11-26_12h14m53.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47085. Clear<y>? yes Entry 'status_2012-11-26_15h06m49.csv' in /var/log/status_logs (46956) has deleted/unused inode 47088. Clear<y>? yes Entry 'status_2012-11-20_14h50m09.csv' in /var/log/status_logs (46956) has deleted/unused inode 47073. Clear<y>? yes Entry 'status_2012-11-20_14h55m32.csv' in /var/log/status_logs (46956) has deleted/unused inode 47074. Clear<y>? yes Entry 'status_2012-11-26_11h04m36.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47078. Clear<y>? yes Entry 'status_2012-11-26_11h54m45.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47082. Clear<y>? yes Entry 'status_2012-11-26_12h12m20.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47084. Clear<y>? yes Entry 'status_2012-11-26_12h33m52.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47086. Clear<y>? yes Entry 'status_2012-11-26_10h51m59.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47077. Clear<y>? yes Entry 'status_2012-11-26_11h17m09.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47079. Clear<y>? yes Entry 'status_2012-11-26_12h54m11.csv.gz' in /var/log/status_logs (46956) has deleted/unused inode 47087. Clear<y>? yes Pass 3: Checking directory connectivity '..' in /etc/network/run (46948) is <The NULL inode> (0), should be /etc/network (46953). Fix<y>? yes Couldn't fix parent of inode 46948: Couldn't find parent directory entry Pass 4: Checking reference counts Unattached inode 46945 Connect to /lost+found<y>? yes Inode 46945 ref count is 2, should be 1. Fix<y>? yes Inode 46953 ref count is 5, should be 4. Fix<y>? yes Pass 5: Checking group summary information Block bitmap differences: -(208264--208266) -(210062--210068) -(211343--211491) -(213241--213250) -(213344--213393) -213397 -(213457--213463) -(213516--213521) -(213628--213655) -(213683--213688) -(213709--213728) -(215265--215300) -(215346--215365) -(221541--221551) -(221696--221704) -227517 Fix<y>? yes Free blocks count wrong for group #6 (17247, counted=17611). Fix<y>? yes Free blocks count wrong (161691, counted=162055). Fix<y>? yes Inode bitmap differences: +(47089--47090) +47093 +47095 +(47097--47099) +(47101--47104) -(47219--47220) -47222 -47224 -47228 -47231 -(47347--47348) -47350 -47352 -47356 -47359 -(47457--47488) -47985 -47996 -(47999--48000) -48017 -(48027--48028) -(48030--48032) -48049 -(48059--48060) -(48062--48064) -48081 -(48091--48092) -(48094--48096) Fix<y>? yes Free inodes count wrong for group #6 (7608, counted=7624). Fix<y>? yes Free inodes count wrong (61919, counted=61935). Fix<y>? yes embeddedrootwrite: ***** FILE SYSTEM WAS MODIFIED ***** embeddedrootwrite: ********** WARNING: Filesystem still has errors ********** embeddedrootwrite: 657/62592 files (24.4% non-contiguous), 87882/249937 blocks Embedded-PC-failsafe:~# Embedded-PC-failsafe:~# e2fsck /dev/sda3 e2fsck 1.41.3 (12-Oct-2008) embeddedrootwrite contains a file system with errors, check forced. Pass 1: Checking inodes, blocks, and sizes Pass 2: Checking directory structure Directory entry for '.' in ... (46948) is big. Split<y>? yes Missing '..' in directory inode 46948. Fix<y>? yes Setting filetype for entry '..' in ... (46948) to 2. Pass 3: Checking directory connectivity '..' in /etc/network/run (46948) is <The NULL inode> (0), should be /etc/network (46953). Fix<y>? yes Pass 4: Checking reference counts Inode 2 ref count is 12, should be 13. Fix<y>? yes Pass 5: Checking group summary information embeddedrootwrite: ***** FILE SYSTEM WAS MODIFIED ***** embeddedrootwrite: 657/62592 files (24.4% non-contiguous), 87882/249937 blocks Embedded-PC-failsafe:~# Embedded-PC-failsafe:~# e2fsck /dev/sda3 e2fsck 1.41.3 (12-Oct-2008) embeddedrootwrite: clean, 657/62592 files, 87882/249937 blocks

    Read the article

  • APPDATA and LOCALAPPDATA environment variables are not set on a profile in Windows 7 Pro 32bit

    - by Timur Fanshteyn
    I am having problem with a user account on a Windows 7 machine (local install, admin user account) APPDATA and LOCALAPPDATA environment are not set. Another user on the same machine, (also a local account, but without admin rights) has the variables set. This started to happen recently, however, I can not figure out if there was something installed on the machine to cause this. This is creating issues with applications that are trying to expand the variables to store local files. Thank you for the help.

    Read the article

  • Are there any Acrobat plugins or standalone programs that allow one to select and extract individual

    - by user30525
    We use BCL Jade currently but are running into problems because it isn't supported or sold anymore, doesn't work on Acrobat 8 or 9, and has some other issues. Other than that though it works great! :) Is there anything like it that allows users to select zones to extract? I see a simaler question on here and and an answer that suggests this http://pdftohtml.sourceforge.net/ but ideally we would want something nonprogrammers could use.

    Read the article

  • Windows 7 x64 "upgrade" repair fails

    - by Polynomial
    I've been running into issues with Windows Update, which I can't seem to fix. The hotfixes don't work, nor does the Windows update readyness tool, or the manual SP1 upgrade. I get various esoteric errors which nobody seems to have a fix for. Looks like some of the update cache is corrupt and digital signatures seem to be broken on some packages / Windows Update components. Long story short, I have discovered the only option is to do a repair operation on the OS, to repair everything. It's so corrupt that only a complete replacement will fix it. According to various sources (including MSKB) one can perform a repair by running an in-place upgrade. I've got the Windows 7 Ultimate retail disc, which I've inserted into my machine. I ran setup.exe and went through in the following order: Install now Go online to get latest updates (I've also tried not getting updates) Wait for updates to be downloaded Select Windows 7 Ultimate (x64 architecture) and click next Accept the T&Cs, click next Click Upgrade At this point it spends a minute on the "checking compatibility" screen, after which I get the following error: The following issues are preventing Windows from upgrading. Cancel the upgrade, complete each task, and then restart the upgrade to continue. You can’t upgrade 64-bit Windows to a 32-bit version of Windows. To upgrade, obtain a 64-bit version of the installation disc, or go online to see how to install Windows 7 and keep your files and settings. 32-bit Windows cannot be upgraded to a 64-bit version of Windows. To upgrade, obtain a 32-bit version of the Windows installation disc. It also mentions a warning about potential conflicts with a storage driver and VS2010, but that doesn't seem to be the blocking issue. My currently installed version of Windows is Ultimate 64-bit (absolutely sure of this) and the disc is definitely a x86 / x64 combined Ultimate retail disc. There seem to be a few people who have run into this (e.g. this question), but I've not seen any answers. I've checked the event viewer, but can't spot anything in there that's related. Any idea how I can get this working? P.S: Just to pre-empt the inevitable "are you suuuuuuuuuuuuure it's x64 Ultimate?" questions:

    Read the article

  • How can I connect DLNA devices through NAT?

    - by Bob
    I have a Windows 7 PC running Serviio as a DLNA server. I have a Samsung I9100G running Skifta as a DLNA renderer (client). My network topology: At the moment, I can connect and watch my videos fine if the phone is on router #2. The server is on a wired network with #2. Router #1 is 192.168.1.1, router #2 is 192.168.2.1 (192.168.1.2) and router #3 is 192.168.3.1 (192.168.1.3). In other words, each router has its own subnet, using NAT - their "modem" port is connected with a "LAN" port on the modem/router 1. What I want to do is be able to connect to the DLNA server if the renderer is connected to router #1/#3 - #1 is on the WAN side of #2, while #3 is even further separated. I'll settle for just #1 working, though. Normally, I would just forward the appropriate ports, and everything would work fine. However, (apparently) DLNA uses UPnP, which I am unfamiliar with. I tried enabling UPnP on router #2, but that did not seem not change anything. It's a Belkin F5D7230-4 6000 - there's reported issues with UPnP on F5D7230-4 7000. UPnP is already enabled on router #1 - a Billion BiPAC 7700N. I've also tried the built in DLNA renderer/server/controller on my phone, Samsung AllShare. It can see the server on router #2 and browse files, but has issues playing or downloading them. It also can't see the server on the other two networks. I'm currently using Skifta/s "local" mode. "Remote" mode requires an account, which I don't really want to create if not necessary. Is it possible too do what I'm trying to do? If no, are there workarounds? If yes, how do I do it? Is my server the issue? The renderer (client)? The router(s)? My method? I can change just about anything except the routers.

    Read the article

  • What Issue Tracking System to select?

    - by Mikee
    What Issue Tracking Sytem is the most appropriate for fast, big, multilingual and international websites? The system has to handle both technical and content/editorial issues. What's the size and type of your site do you run? Whart System are you using for the keeping it state of the art? Thanks a lot for sharing your good or bad experience.

    Read the article

  • Linking JIRA and Confluence

    - by William
    I am trying to create a trust relationship between JIRA and Confluence so that I can insert JIRA issues into Confluence documents. However, in JIRA, when I try to initiate the relationship, I receive the error: "Unable to auto-configure a Consumer as the remote Consumer-Info count not be found.". When I attempt to create the relationship from Confluence, I receive this error: "Unable to auto-configure a Consumer as the remote Consumer-Info could not be found." What am I doing wrong here?

    Read the article

  • Splitting an internet connection between multiple separate subnetworks

    - by pythonian4000
    Problem I have an internet connection that I want to split between four separate networks. My requirements are: I need to be able to monitor the amount of bandwidth and data being used by each network, and notify or control as necessary. The four networks should only be able to connect to the internet, not each other. My parents need to be able to operate it, so it needs a simple, preferably Windows-based GUI. Progress so far Server I have a mini-ITX server with six Gigabit ethernet ports - one for the ethernet internet connection, one for each of the four networks, and one for remote access to the server for administration. Bandwidth control I spent a long time researching solutions here. The majority of the control systems/software I found could control bandwidth usage via QOS, but could not monitor or control the amount of data being used. Eventually I found the SoftPerfect Bandwidth Manager, which has everything I need in terms of monitoring and control - per-interface quota management, usage statistics, a web interface for checking usage, and email notifications when quotas are exceeded. It is also Windows-based and has a simple GUI. Internet sharing This is where I am having issues. I am currently using Windows XP Pro SP2 for the server (yes, I know this is far from ideal, but it's the only spare Windows OS I currently have). I can't use the built-in Internet Connection Sharing for several reasons: The upstream internet router has an IP of 192.168.0.1 which ICS clashes with, and I cannot change the router settings. ICS can only share an internet connection with a single interface, but I have four. I have tried bridging the four network cards, but then the Bandwidth Manager cannot see the four individual interfaces - it only sees the bridge. I have tried setting up Dual DHCP DNS server (and am having issues getting DHCP offers to be received by clients), but that would still require gateway software of some sort, which I have been unable to find. My current attempt is to use OpenVPN, with a server for the internet NIC and a separate client for each of the four networks. My thought is that I could bridge the OpenVPN TAP devices to each NIC, meaning that the Bandwidth Manager would control traffic from the bridge instead of the interface. I have not made much progress here though - I've never used OpenVPN before. Questions Is there a Windows software package that does everything I need? (Unlikely, I know) Is there a Windows software package that will share internet between multiple NICs without bridging? Are either of my about attempts feasible? Would it help to have a newer/server version of Windows? Is there a non-Windows alternative that is easy to use?

    Read the article

  • TCP/IP networking working as expected, but can't access Windows Shares

    - by Pablo Santa Cruz
    I am trying to fix a Windows 7 Pro SP1 (32 bits) computer. I have a weird problem. It was working fine until two days ago (didn't do anything weird in that day), and suddenly windows network (accessing to Windows Shares, sharing my printer) stopped working. TCP/IP networks words without issues, since I can IM, use the WebBrowser, check my email, you name it. Any ideas on how could I attempt to fix this?

    Read the article

  • is there anyway to know if your supposedly fully dedicated server is really a virtually resource-sha

    - by siran
    Hi, sometimes I feel my server not responding as smoothly as I would expect (i have a Intel(R) Xeon(TM) CPU 2.80GHz Quad Core), given that for example, the 'top' commands reports a low load < 0.5, CPU are almost completely idle ... I maybe have internet connectivity issues, so I don't really know if it's me or if it's the server itself. Is there anykind of benchmarking script (or something analogous) I could run and see the actual performance of the server ?

    Read the article

  • How do you transfer AWS RDS snap shot to a different AWS account

    - by Webmonger
    Hi I have an RDS database that I need to transfer a snapshot of to another AWS account. I understand there are issues being able to do this between availability zones so I'm really unsure if this is possible. The RDS instance is mySql. If it's not possible to transfer the snapshot please could you explain how to transfer the data from one RDS instance to another without downloading any if the contents(The DB is over 200GB). Thanks in advance

    Read the article

  • Is there another way to run Apache2 securely for end users without using CGI mode?

    - by Volomike
    Is there another way to run Apache2 securely for multiple end users (like hosting hundreds of blogs) without using CGI mode as required by suPHP? It just seems so inefficient to use CGI mode for PHP when if we could set up permissions properly, we could host PHP through mod_php perhaps? I mean, I do want to restrict these users to their home directories for their sites, but don't want any security issues.

    Read the article

  • Dovecot, IMAP outlook reports error 0x800CCC0E cannot synchronize subscribed folders

    - by l1em1on1
    I have recently some issues with people using my email server. They have problems with synchronizing folders on outlook, and I can't figure out what to do. I found somewhere that I could extend a setting for imap connections: mail_max_userip_connections = 20 which didn't really help, I was thinking about extending timeout of connection or something, but really can find anything like that. In Thunderbird it seems to be OK. here is dovecot -p result: http://snipt.org/AAig5 if anything could help please let me know what should provide.

    Read the article

  • Email: X-Authentication-Warning

    - by stef
    We're sending out 1000's of mails per day from our site (mainly "click here to verify your subscription") and too many are getting flagged by spam (mainly hotmail). One of the things I noticed in the headers is X-Authentication-Warning: srv01.site.com: www-data set sender to [email protected] using -f Is this something I should be worried about, that may cause spam flags to raise? (I'm already checking various issues that have been mentioned regarding spam flagging over at stackoverflow, I know there are many factors in play)

    Read the article

  • MegaCLI always returns blank output

    - by JamesHannah
    This server is a Dell R200 running Ubuntu 8.04LTS using a LSI SAS1068E raid card supplied from Dell, I suspect that there might be some kind of RAID issue with the hardware raid built into the motherboard, but I can't seem to get MegaCLi to return any useful output: root@81 $ ./MegaCli -AdpAllInfo -aALL root@81 $ ./MegaCli -PDList -aALL root@81 $ The disks work and AFAIK the raid software is installed correctly. I've seen this issue on RedHat issues also in the past. The RAID was initially setup through the BIOS on this server and appears to be functioning fine apart from this.

    Read the article

  • Dell PowerEdge Server BitLocker Hotswap Hard disks

    - by JoshODBrown
    We have a Windows 2008 R2 Server running on a Dell PowerEdge R310 Server with Bitlocker enabled. There are two physical Hard disks configured as RAID 1. One of the disks recently started having an issue, so we have now have a warranty covered replacement for it, But we were curious if there will be any issues hot swapping the new drive in due to BitLocker being enabled? Has anyone had a similar experience with scenario?

    Read the article

  • Installing ImageMagick on Mac OSX 10.6

    - by Russell C.
    I just got a new Mac and am trying to setup a local Perl development environment. I'm using MAMP but also need the ImageMagick perl module installed in order to do some of the photo processing our scripts require. I tried installing ImageMagick manually but ran into some issues and after reading online a lot of people reported having issues going this route. The general consensus was to install it using MacPorts instead so I went ahead and installed MacPorts. Unfortunately, MacPorts can't seem to install it successfully either. Here is the command I'm using to try to install ImageMagick: sudo port install p5-perlmagick And here are all the errors reported during install: ---> Computing dependencies for p5-perlmagick ---> Building p5-perlmagick Error: Target org.macports.build returned: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_perl_p5-perlmagick/work/PerlMagick-6.32" && /usr/bin/make -j2 all " returned error 2 Command output: Magick.xs:10918: error: 'struct Methods' has no member named 'exception' Magick.xs:10918: error: request for member 'severity' in something not a structure or union Magick.xs:10918: error: 'ErrorException' undeclared (first use in this function) Magick.xs:10919: error: 'struct Methods' has no member named 'exception' Magick.xs:10920: warning: implicit declaration of function 'GetImageException' Magick.xs:10922: error: 'struct PackageInfo' has no member named 'image_info' Magick.xs:10922: error: 'struct Methods' has no member named 'adjoin' Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: 'UndefinedException' undeclared (first use in this function) Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'reason' in something not a structure or union Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'reason' in something not a structure or union Magick.xs:10929: warning: pointer/integer type mismatch in conditional expression Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: error: request for member 'severity' in something not a structure or union Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: warning: pointer/integer type mismatch in conditional expression Magick.xs:10929: error: request for member 'description' in something not a structure or union Magick.xs:10929: warning: passing argument 2 of 'Perl_sv_catpv' from incompatible pointer type Magick.xs:10929: warning: unused variable 'message' Magick.xs:10856: warning: unused variable 'filename' Magick.c:10784: warning: unused variable 'ref' Magick.c:10777: warning: unused variable 'ix' Magick.xs: In function 'boot_Image__Magick': Magick.xs:2122: warning: implicit declaration of function 'InitializeMagick' Magick.xs:2123: warning: implicit declaration of function 'SetWarningHandler' Magick.xs:2124: warning: implicit declaration of function 'SetErrorHandler' make: *** [Magick.o] Error 1 Error: Status 1 encountered during processing. Before reporting a bug, first run the command again with the -d flag to get complete output. I have no idea what the problem might be or how to go about successfully installing ImageMagick. I'd appreciate any help & advice that someone out there that has done this successfully might be able to provide. Thanks in advance!

    Read the article

  • Zimbra mail server: Changing max message size problem

    - by s4uadmin
    Hello, We are having some issues with changing the maximum message size in zimbra We followed the instructions given on the zimbra wiki zimbra@ZIM1:~$ zmprov modifyConfig zimbraMtaMaxMessageSize 2048000 zimbra@ZIM1:~$ postfix reload postfix/postfix-script: refreshing the Postfix mail system zimbra@ZIM1:~$ postconf | grep message_size_limit message_size_limit = 10240000 Strange thing: The setting displayed in the admin page does change but not to the corresponding size (2000kb) It would be much appreciated if someone can help us. Grtz, Thomas

    Read the article

  • Critix XenServer - VM

    - by khou
    1 Is it a good idea to export a VM from one server and import the VM into a completely different server? 2 Would there be any issues? 3 or is it better to just reinstall and reconfiguration everything on the new server (this is good but its rather time consuming).

    Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >