Search Results

Search found 5638 results on 226 pages for 'debian sys maint'.

Page 117/226 | < Previous Page | 113 114 115 116 117 118 119 120 121 122 123 124  | Next Page >

• Xen DomU on DRBD device: barrier errors

  - by Halfgaar

  I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

  Read the article

• Linux Kernel crash mutex_lock_slowpath "blocked for more than 120 seconds". What to do?

  - by Roddick

  I have out-of-the box Debian Lenny with non-custom kernel 2.6.26-2-amd64. Brand new server that is used to 5% of it's potential, CPU and Disk-wise. Meaning it probably not crashing because of overload. every few days it freezes with hundreds of these messages in console log: : [284847.828428] INFO: task apache2:12473 blocked for more than 120 seconds. : [284847.868468] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [284847.912759] apache2 D ffff8101bc6b7ab0 0 12473 14358 : [284847.912763] ffff810160d5bc50 0000000000000082 ffff8101c0002e40 0000000000000000 : [284847.912766] ffff8101a7c42950 ffff810327d92810 ffff8101a7c42bd8 0000000400000044 : [284847.912770] ffff8101c0002e40 00000000000612d0 0000000000000000 00000040000612d0 : [284847.912773] Call Trace: : [284847.912786] [<ffffffff80429b0d>] __mutex_lock_slowpath+0x64/0x9b : [284847.912790] [<ffffffff80429972>] mutex_lock+0xa/0xb : [284847.912794] [<ffffffff802a20b9>] do_lookup+0x82/0x1c1 : [284847.912800] [<ffffffff802a4271>] __link_path_walk+0x87a/0xd19 : [284847.912805] [<ffffffff80295844>] kmem_getpages+0x96/0x15f : [284847.912808] [<ffffffff80295fb7>] ____cache_alloc_node+0x6d/0x106 : [284847.912814] [<ffffffff802a4756>] path_walk+0x46/0x8b : [284847.912819] [<ffffffff802a4a82>] do_path_lookup+0x158/0x1cf : [284847.912822] [<ffffffff802a3879>] getname+0x140/0x1a7 : [284847.912827] [<ffffffff802a53f1>] __user_walk_fd+0x37/0x4c : [284847.912831] [<ffffffff8029e381>] vfs_lstat_fd+0x18/0x47 : [284847.912840] [<ffffffff8029e3c9>] sys_newlstat+0x19/0x31 : [284847.912848] [<ffffffff8020beda>] system_call_after_swapgs+0x8a/0x8f Almost all traces has __mutex_lock_slowpath as top-level. Only some has different trace: : [284847.737386] INFO: task apache2:12472 blocked for more than 120 seconds. : [284847.777551] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [284847.824881] apache2 D ffff8101bc6b7ab0 0 12472 14358 : [284847.824886] ffff8101b9cc1c50 0000000000000086 ffffffffa0131e0a 0000000000000002 : [284847.824889] ffff8102e7454300 ffff810324c6cad0 ffff8102e7454588 0000000000000000 : [284847.824893] 0000000000000001 0000000000000296 0000000000000003 ffff8101b9cc1c58 : [284847.824896] Call Trace: : [284847.828403] [<ffffffffa0131e0a>] :ext3:__ext3_journal_dirty_metadata+0x1e/0x46 : [284847.828412] [<ffffffff80429b0d>] __mutex_lock_slowpath+0x64/0x9b : [284847.828418] [<ffffffff80429972>] mutex_lock+0xa/0xb : [284847.828421] [<ffffffff802a20b9>] do_lookup+0x82/0x1c1 : [284847.828427] [<ffffffff802a4271>] __link_path_walk+0x87a/0xd19 : [284847.828428] [<ffffffff80271296>] find_lock_page+0x1f/0x8a : [284847.828428] [<ffffffff80273182>] filemap_fault+0x1c2/0x33c : [284847.828428] [<ffffffff802a4756>] path_walk+0x46/0x8b : [284847.828428] [<ffffffff802a4a82>] do_path_lookup+0x158/0x1cf : [284847.828428] [<ffffffff802a3879>] getname+0x140/0x1a7 : [284847.828428] [<ffffffff802a53f1>] __user_walk_fd+0x37/0x4c : [284847.828428] [<ffffffff8029e381>] vfs_lstat_fd+0x18/0x47 : [284847.828428] [<ffffffff8029e3c9>] sys_newlstat+0x19/0x31 : [284847.828428] [<ffffffff8020beda>] system_call_after_swapgs+0x8a/0x8f kernel: [1912668.466347] INFO: task apache2:17984 blocked for more than 120 seconds. [1912668.507035] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. : [1912668.555165] apache2 D ffff8101c5637ba0 0 17984 17282 : [1912668.596752] ffff810166a7dd30 0000000000000086 0000000000000000 ffff810166a7dcd8 : [1912668.643341] ffff8101c563c880 ffff81024505f000 0000000000000002 ffff810166a7dd68 : [1912668.699566] 0000000000000086 00000000000cb1a0 0000000000000000 ffff81017f344d60 : [1912668.744773] Call Trace: : [1912668.761754] [<ffffffff8022a3ed>] pick_next_task_fair+0x6e/0x7a : [1912668.829311] [<ffffffff802be0e2>] bio_alloc_bioset+0x89/0xd9 : [1912668.861930] [<ffffffff8024ac3a>] getnstimeofday+0x39/0x98 : [1912668.897005] [<ffffffff802710f6>] sync_page+0x0/0x41 : [1912668.927868] [<ffffffff80429487>] io_schedule+0x5c/0x9e : [1912668.960286] [<ffffffff80271132>] sync_page+0x3c/0x41 : [1912668.991756] [<ffffffff804295fa>] __wait_on_bit_lock+0x36/0x66 : [1912669.031757] [<ffffffff802710e3>] __lock_page+0x5e/0x64 : [1912669.064191] [<ffffffff802461d3>] wake_bit_function+0x0/0x23 : [1912669.100100] [<ffffffff80281bc5>] handle_mm_fault+0x5e4/0x8de : [1912669.134531] [<ffffffff802461a5>] autoremove_wake_function+0x0/0x2e : [1912669.174623] [<ffffffff802aa108>] fcntl_setlk+0x1cf/0x291 : [1912669.210623] [<ffffffff802461a5>] autoremove_wake_function+0x0/0x2e : [1912669.246923] [<ffffffff802a677f>] sys_fcntl+0x280/0x2f7 After googling for "mutex_lock_slowpath" I can only find the Kernel mailing list discussions that this issue was introduced in some commit. Wthout reference to verison. Discussions as recent as Jan 25, 2011. The Kernel I am using is form Debian Lenny, year ago. What should I do? Is this bug even fixed in kernel? if it's such obvious bug why it happens so rarely? Should I download latest kernel from kernel.org and upgrade? Should I use Debian backports to install new "Approved" kernel? Am I missing something? What to do?

  Read the article

• T-SQL Tuesday #33: Trick Shots: Undocumented, Underdocumented, and Unknown Conspiracies!

  - by Most Valuable Yak (Rob Volk)

  Mike Fal (b | t) is hosting this month's T-SQL Tuesday on Trick Shots.  I love this choice because I've been preoccupied with sneaky/tricky/evil SQL Server stuff for a long time and have been presenting on it for the past year.  Mike's directives were "Show us a cool trick or process you developed…It doesn’t have to be useful", which most of my blogging definitely fits, and "Tell us what you learned from this trick…tell us how it gave you insight in to how SQL Server works", which is definitely a new concept.  I've done a lot of reading and watching on SQL Server Internals and even attended training, but sometimes I need to go explore on my own, using my own tools and techniques.  It's an itch I get every few months, and, well, it sure beats workin'. I've found some people to be intimidated by SQL Server's internals, and I'll admit there are A LOT of internals to keep track of, but there are tons of excellent resources that clearly document most of them, and show how knowing even the basics of internals can dramatically improve your database's performance.  It may seem like rocket science, or even brain surgery, but you don't have to be a genius to understand it. Although being an "evil genius" can help you learn some things they haven't told you about. ;) This blog post isn't a traditional "deep dive" into internals, it's more of an approach to find out how a program works.  It utilizes an extremely handy tool from an even more extremely handy suite of tools, Sysinternals.  I'm not the only one who finds Sysinternals useful for SQL Server: Argenis Fernandez (b | t), Microsoft employee and former T-SQL Tuesday host, has an excellent presentation on how to troubleshoot SQL Server using Sysinternals, and I highly recommend it.  Argenis didn't cover the Strings.exe utility, but I'll be using it to "hack" the SQL Server executable (DLL and EXE) files. Please note that I'm not promoting software piracy or applying these techniques to attack SQL Server via internal knowledge. This is strictly educational and doesn't reveal any proprietary Microsoft information.  And since Argenis works for Microsoft and demonstrated Sysinternals with SQL Server, I'll just let him take the blame for it. :P (The truth is I've used Strings.exe on SQL Server before I ever met Argenis.) Once you download and install Strings.exe you can run it from the command line.  For our purposes we'll want to run this in the Binn folder of your SQL Server instance (I'm referencing SQL Server 2012 RTM): cd "C:\Program Files\Microsoft SQL Server\MSSQL11\MSSQL\Binn" C:\Program Files\Microsoft SQL Server\MSSQL11\MSSQL\Binn> strings *sql*.dll > sqldll.txt C:\Program Files\Microsoft SQL Server\MSSQL11\MSSQL\Binn> strings *sql*.exe > sqlexe.txt   I've limited myself to DLLs and EXEs that have "sql" in their names.  There are quite a few more but I haven't examined them in any detail. (Homework assignment for you!) If you run this yourself you'll get 2 text files, one with all the extracted strings from every SQL DLL file, and the other with the SQL EXE strings.  You can open these in Notepad, but you're better off using Notepad++, EditPad, Emacs, Vim or another more powerful text editor, as these will be several megabytes in size. And when you do open it…you'll find…a TON of gibberish.  (If you think that's bad, just try opening the raw DLL or EXE file in Notepad.  And by the way, don't do this in production, or even on a running instance of SQL Server.)  Even if you don't clean up the file, you can still use your editor's search function to find a keyword like "SELECT" or some other item you expect to be there.  As dumb as this sounds, I sometimes spend my lunch break just scanning the raw text for anything interesting.  I'm boring like that. Sometimes though, having these files available can lead to some incredible learning experiences.  For me the most recent time was after reading Joe Sack's post on non-parallel plan reasons.  He mentions a new SQL Server 2012 execution plan element called NonParallelPlanReason, and demonstrates a query that generates "MaxDOPSetToOne".  Joe (formerly on the Microsoft SQL Server product team, so he knows this stuff) mentioned that this new element was not currently documented and tried a few more examples to see what other reasons could be generated. Since I'd already run Strings.exe on the SQL Server DLLs and EXE files, it was easy to run grep/find/findstr for MaxDOPSetToOne on those extracts.  Once I found which files it belonged to (sqlmin.dll) I opened the text to see if the other reasons were listed.  As you can see in my comment on Joe's blog, there were about 20 additional non-parallel reasons.  And while it's not "documentation" of this underdocumented feature, the names are pretty self-explanatory about what can prevent parallel processing. I especially like the ones about cursors – more ammo! - and am curious about the PDW compilation and Cloud DB replication reasons. One reason completely stumped me: NoParallelHekatonPlan.  What the heck is a hekaton?  Google and Wikipedia were vague, and the top results were not in English.  I found one reference to Greek, stating "hekaton" can be translated as "hundredfold"; with a little more Wikipedia-ing this leads to hecto, the prefix for "one hundred" as a unit of measure.  I'm not sure why Microsoft chose hekaton for such a plan name, but having already learned some Greek I figured I might as well dig some more in the DLL text for hekaton.  Here's what I found: hekaton_slow_param_passing Occurs when a Hekaton procedure call dispatch goes to slow parameter passing code path The reason why Hekaton parameter passing code took the slow code path hekaton_slow_param_pass_reason sp_deploy_hekaton_database sp_undeploy_hekaton_database sp_drop_hekaton_database sp_checkpoint_hekaton_database sp_restore_hekaton_database e:\sql11_main_t\sql\ntdbms\hekaton\sqlhost\sqllang\hkproc.cpp e:\sql11_main_t\sql\ntdbms\hekaton\sqlhost\sqllang\matgen.cpp e:\sql11_main_t\sql\ntdbms\hekaton\sqlhost\sqllang\matquery.cpp e:\sql11_main_t\sql\ntdbms\hekaton\sqlhost\sqllang\sqlmeta.cpp e:\sql11_main_t\sql\ntdbms\hekaton\sqlhost\sqllang\resultset.cpp Interesting!  The first 4 entries (in red) mention parameters and "slow code".  Could this be the foundation of the mythical DBCC RUNFASTER command?  Have I been passing my parameters the slow way all this time? And what about those sp_xxxx_hekaton_database procedures (in blue)? Could THEY be the secret to a faster SQL Server? Could they promise a "hundredfold" improvement in performance?  Are these special, super-undocumented DIB (databases in black)? I decided to look in the SQL Server system views for any objects with hekaton in the name, or references to them, in hopes of discovering some new code that would answer all my questions: SELECT name FROM sys.all_objects WHERE name LIKE '%hekaton%' SELECT name FROM sys.all_objects WHERE object_definition(OBJECT_ID) LIKE '%hekaton%' Which revealed: name ------------------------ (0 row(s) affected) name ------------------------ sp_createstats sp_recompile sp_updatestats (3 row(s) affected)   Hmm.  Well that didn't find much.  Looks like these procedures are seriously undocumented, unknown, perhaps forbidden knowledge. Maybe a part of some unspeakable evil? (No, I'm not paranoid, I just like mysteries and thought that punching this up with that kind of thing might keep you reading.  I know I'd fall asleep without it.) OK, so let's check out those 3 procedures and see what they reveal when I search for "Hekaton": sp_createstats: -- filter out local temp tables, Hekaton tables, and tables for which current user has no permissions -- Note that OBJECTPROPERTY returns NULL on type="IT" tables, thus we only call it on type='U' tables   OK, that's interesting, let's go looking down a little further: ((@table_type<>'U') or (0 = OBJECTPROPERTY(@table_id, 'TableIsInMemory'))) and -- Hekaton table   Wellllll, that tells us a few new things: There's such a thing as Hekaton tables (UPDATE: I'm not the only one to have found them!) They are not standard user tables and probably not in memory UPDATE: I misinterpreted this because I didn't read all the code when I wrote this blog post. The OBJECTPROPERTY function has an undocumented TableIsInMemory option Let's check out sp_recompile: -- (3) Must not be a Hekaton procedure.   And once again go a little further: if (ObjectProperty(@objid, 'IsExecuted') <> 0 AND ObjectProperty(@objid, 'IsInlineFunction') = 0 AND ObjectProperty(@objid, 'IsView') = 0 AND -- Hekaton procedure cannot be recompiled -- Make them go through schema version bumping branch, which will fail ObjectProperty(@objid, 'ExecIsCompiledProc') = 0)   And now we learn that hekaton procedures also exist, they can't be recompiled, there's a "schema version bumping branch" somewhere, and OBJECTPROPERTY has another undocumented option, ExecIsCompiledProc.  (If you experiment with this you'll find this option returns null, I think it only works when called from a system object.) This is neat! Sadly sp_updatestats doesn't reveal anything new, the comments about hekaton are the same as sp_createstats.  But we've ALSO discovered undocumented features for the OBJECTPROPERTY function, which we can now search for: SELECT name, object_definition(OBJECT_ID) FROM sys.all_objects WHERE object_definition(OBJECT_ID) LIKE '%OBJECTPROPERTY(%'   I'll leave that to you as more homework.  I should add that searching the system procedures was recommended long ago by the late, great Ken Henderson, in his Guru's Guide books, as a great way to find undocumented features.  That seems to be really good advice! Now if you're a programmer/hacker, you've probably been drooling over the last 5 entries for hekaton (in green), because these are the names of source code files for SQL Server!  Does this mean we can access the source code for SQL Server?  As The Oracle suggested to Neo, can we return to The Source??? Actually, no. Well, maybe a little bit.  While you won't get the actual source code from the compiled DLL and EXE files, you'll get references to source files, debugging symbols, variables and module names, error messages, and even the startup flags for SQL Server.  And if you search for "DBCC" or "CHECKDB" you'll find a really nice section listing all the DBCC commands, including the undocumented ones.  Granted those are pretty easy to find online, but you may be surprised what those web sites DIDN'T tell you! (And neither will I, go look for yourself!)  And as we saw earlier, you'll also find execution plan elements, query processing rules, and who knows what else.  It's also instructive to see how Microsoft organizes their source directories, how various components (storage engine, query processor, Full Text, AlwaysOn/HADR) are split into smaller modules. There are over 2000 source file references, go do some exploring! So what did we learn?  We can pull strings out of executable files, search them for known items, browse them for unknown items, and use the results to examine internal code to learn even more things about SQL Server.  We've even learned how to use command-line utilities!  We are now 1337 h4X0rz!  (Not really.  I hate that leetspeak crap.) Although, I must confess I might've gone too far with the "conspiracy" part of this post.  I apologize for that, it's just my overactive imagination.  There's really no hidden agenda or conspiracy regarding SQL Server internals.  It's not The Matrix.  It's not like you'd find anything like that in there: Attach Matrix Database DM_MATRIX_COMM_PIPELINES MATRIXXACTPARTICIPANTS dm_matrix_agents   Alright, enough of this paranoid ranting!  Microsoft are not really evil!  It's not like they're The Borg from Star Trek: ALTER FEDERATION DROP ALTER FEDERATION SPLIT DROP FEDERATION   #tsql2sday

  Read the article

• Using a portable USB monitor in Ubuntu 13.04 (AOC e1649Fwu - DisplayLink)

  Having access to a little bit of IT hardware extravaganza isn't that easy here in Mauritius for exactly two reasons - either it is simply not available or it is expensive like nowhere. Well, by chance I came across an advert by a local hardware supplier and their offer of the week caught my attention - a portable USB monitor. Sounds cool, and the specs are okay as well. It's completely driven via USB 2.0, has a light weight, the dimensions would fit into my laptop bag and the resolution of 1366 x 768 pixels is okay for a second screen. Long story, short ending: I called them and only got to understand that they are out of stock - how convenient! Well, as usual I left some contact details and got the regular 'We call you back' answer. Surprisingly, I didn't receive a phone call as promised and after starting to complain via social media networks they finally came back to me with new units available - and *drum-roll* still the same price tag as promoted (and free delivery on top as one of their employees lives in Flic en Flac). Guess, it was a no-brainer to get at least one unit to fool around with. In worst case it might end up as image frame on the shelf or so... The usual suspects... Ubuntu first! Of course, the packing mentions only Windows or Mac OS as supported operating systems and without hesitation at all, I hooked up the device on my main machine running on Ubuntu 13.04. Result: Blackout... Hm, actually not the situation I was looking for but okay can't be too difficult to get this piece of hardware up and running. Following the output of syslogd (or dmesg if you prefer) the device has been recognised successfully but we got stuck in the initialisation phase. Oct 12 08:17:23 iospc2 kernel: [69818.689137] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 12 08:17:23 iospc2 kernel: [69818.800306] usb 2-4: device descriptor read/64, error -32Oct 12 08:17:24 iospc2 kernel: [69819.043620] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 08:17:24 iospc2 kernel: [69819.043630] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 08:17:24 iospc2 kernel: [69819.043636] usb 2-4: Product: e1649FwuOct 12 08:17:24 iospc2 kernel: [69819.043642] usb 2-4: Manufacturer: DisplayLinkOct 12 08:17:24 iospc2 kernel: [69819.043647] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 08:17:24 iospc2 kernel: [69819.046073] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 08:17:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 08:17:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 12 08:17:30 iospc2 kernel: [69825.411220] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 12 08:17:30 iospc2 kernel: [69825.498778] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 12 08:17:30 iospc2 kernel: [69825.498786] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 12 08:17:30 iospc2 kernel: [69825.498909] usbcore: registered new interface driver udl The device has been recognised as USB device without any question and it is listed properly: # lsusb...Bus 002 Device 005: ID 17e9:4107 DisplayLink ... A quick and dirty research on the net gave me some hints towards the udlfb framebuffer device for USB DisplayLink devices. By default this kernel module is blacklisted $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udl#blacklist udlblacklist udlfb and it is recommended to load it manually. So, unloading the whole udl stack and giving udlfb a shot: Oct 12 08:22:31 iospc2 kernel: [70126.642809] usbcore: registered new interface driver udlfb But still no reaction on the external display which supposedly should have been on and green. Display okay? Test run on Windows Just to be on the safe side and to exclude any hardware related defects or whatsoever - you never know what happened during delivery. I moved the display to a new position on the opposite side of my laptop, installed the display drivers first in Windows Vista (I know, I know...) as recommended in the manual, and then finally hooked it up on that machine. Tada! Display has been recognised correctly and I have a proper choice between cloning and extending my desktop. Testing whether the display is working properly - using Windows Vista Okay, good to know that there is nothing wrong on the hardware side just software... Back to Ubuntu - Kernel too old Some more research on Google and various hits recommend that the original displaylink driver has been merged into the recent kernel development and one should manually upgrade the kernel image (and both header) packages for Ubuntu. At least kernel 3.9 or higher would be necessary, and so I went out to this URL: http://kernel.ubuntu.com/~kernel-ppa/mainline/ and I downloaded all the good stuff from the v3.9-raring directory. The installation itself is easy going via dpkg: $ sudo dpkg -i linux-image-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb$ sudo dpkg -i linux-headers-3.9.0-030900_3.9.0-030900.201304291257_all.deb$ sudo dpkg -i linux-headers-3.9.0-030900-generic_3.9.0-030900.201304291257_amd64.deb As with any kernel upgrades it is necessary to restart the system in order to use the new one. Said and done: $ uname -r3.9.0-030900-generic And now connecting the external display gives me the following output in /var/log/syslog: Oct 12 17:51:36 iospc2 kernel: [ 2314.984293] usb 2-4: new high-speed USB device number 6 using ehci-pciOct 12 17:51:36 iospc2 kernel: [ 2315.096257] usb 2-4: device descriptor read/64, error -32Oct 12 17:51:36 iospc2 kernel: [ 2315.337105] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 12 17:51:36 iospc2 kernel: [ 2315.337115] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 12 17:51:36 iospc2 kernel: [ 2315.337122] usb 2-4: Product: e1649FwuOct 12 17:51:36 iospc2 kernel: [ 2315.337127] usb 2-4: Manufacturer: DisplayLinkOct 12 17:51:36 iospc2 kernel: [ 2315.337132] usb 2-4: SerialNumber: FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338292] udlfb: DisplayLink e1649Fwu - serial #FJBD7HA000778Oct 12 17:51:36 iospc2 kernel: [ 2315.338299] udlfb: vid_17e9&pid_4107&rev_0129 driver's dlfb_data struct at ffff880117e59000Oct 12 17:51:36 iospc2 kernel: [ 2315.338303] udlfb: console enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338306] udlfb: fb_defio enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338309] udlfb: shadow enable=1Oct 12 17:51:36 iospc2 kernel: [ 2315.338468] udlfb: vendor descriptor length:17 data:17 5f 01 0015 05 00 01 03 00 04Oct 12 17:51:36 iospc2 kernel: [ 2315.338473] udlfb: DL chip limited to 1500000 pixel modesOct 12 17:51:36 iospc2 kernel: [ 2315.338565] udlfb: allocated 4 65024 byte urbsOct 12 17:51:36 iospc2 kernel: [ 2315.343592] hid-generic 0003:17E9:4107.0009: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 12 17:51:36 iospc2 mtp-probe: checking bus 2, device 6: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 12 17:51:36 iospc2 mtp-probe: bus: 2, device: 6 was not an MTP deviceOct 12 17:51:36 iospc2 kernel: [ 2315.426583] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.426589] udlfb: Reallocating framebuffer. Addresses will change!Oct 12 17:51:36 iospc2 kernel: [ 2315.428338] udlfb: 1366x768 @ 59 Hz valid modeOct 12 17:51:36 iospc2 kernel: [ 2315.428343] udlfb: set_par mode 1366x768Oct 12 17:51:36 iospc2 kernel: [ 2315.430620] udlfb: DisplayLink USB device /dev/fb1 attached. 1366x768 resolution. Using 4104K framebuffer memory Okay, that's looks more promising but still only blackout on the external screen... And yes, due to my previous modifications I swapped the blacklisted kernel modules: $ less /etc/modprobe.d/blacklist-framebuffer.conf | grep udlblacklist udl#blacklist udlfb Silly me! Okay, back to the original situation in which udl is allowed and udlfb blacklisted. Now, the logging looks similar to this and the screen shows those maroon-brown and azure-blue horizontal bars as described on other online resources. Oct 15 21:27:23 iospc2 kernel: [80934.308238] usb 2-4: new high-speed USB device number 5 using ehci-pciOct 15 21:27:23 iospc2 kernel: [80934.420244] usb 2-4: device descriptor read/64, error -32Oct 15 21:27:24 iospc2 kernel: [80934.660822] usb 2-4: New USB device found, idVendor=17e9, idProduct=4107Oct 15 21:27:24 iospc2 kernel: [80934.660832] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3Oct 15 21:27:24 iospc2 kernel: [80934.660838] usb 2-4: Product: e1649FwuOct 15 21:27:24 iospc2 kernel: [80934.660844] usb 2-4: Manufacturer: DisplayLinkOct 15 21:27:24 iospc2 kernel: [80934.660850] usb 2-4: SerialNumber: FJBD7HA000778Oct 15 21:27:24 iospc2 kernel: [80934.663391] hid-generic 0003:17E9:4107.0008: hiddev0,hidraw5: USB HID v1.10 Device [DisplayLink e1649Fwu] on usb-0000:00:1d.7-4/input1Oct 15 21:27:24 iospc2 mtp-probe: checking bus 2, device 5: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-4"Oct 15 21:27:24 iospc2 mtp-probe: bus: 2, device: 5 was not an MTP deviceOct 15 21:27:25 iospc2 kernel: [80935.742407] [drm] vendor descriptor length:17 data:17 5f 01 00 15 05 00 01 03 00 04Oct 15 21:27:25 iospc2 kernel: [80935.834403] udl 2-4:1.0: fb1: udldrmfb frame buffer deviceOct 15 21:27:25 iospc2 kernel: [80935.834416] [drm] Initialized udl 0.0.1 20120220 on minor 1Oct 15 21:27:25 iospc2 kernel: [80935.836389] usbcore: registered new interface driver udlOct 15 21:27:25 iospc2 kernel: [80936.021458] [drm] write mode info 153 Next, it's time to enable the display for our needs... This can be done either via UI or console, just as you'd prefer it. Adding the external USB display under Linux isn't an issue after all... Settings Manager => Display Personally, I like the console. With the help of xrandr we get the screen identifier first $ xrandrScreen 0: minimum 320 x 200, current 3200 x 1080, maximum 32767 x 32767LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm...DVI-0 connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 193mm   1366x768       60.0*+ and then give it the usual shot with auto-configuration. Let the system decide what's best for your hardware... $ xrandr --output DVI-0 --off$ xrandr --output DVI-0 --auto And there we go... Cloned output of main display: New kernel, new display... The external USB display works out-of-the-box with a Linux kernel > 3.9.0. Despite of a good number of resources it is absolutely not necessary to create a Device or Screen section in one of Xorg.conf files. This information belongs to the past and is not valid on kernel 3.9 or higher. Same hardware but Windows 8 Of course, I wanted to know how the latest incarnation from Redmond would handle the new hardware... Flawless! Most interesting aspect here: I did not use the driver installation medium on purpose. And I was right... not too long afterwards a dialog with the EULA of DisplayLink appeared on the main screen. And after confirmation of same it took some more seconds and the external USB monitor was ready to rumble. Well, and not only that one... but see for yourself. This time Windows 8 was the easiest solution after all. Resume I can highly recommend this type of hardware to anyone asking me. Although, it's dimensions are 15.6" it is actually lighter than my Samsung Galaxy Tab 10.1 and it still fits into my laptop bag without any issues. From now on... no more single screen while developing software on the road!

  Read the article

• Confusion related to sigwait in multiprocess system

  - by user34790

  I am having difficulty in understanding IPC in multiprocess system. I have this system where there are three child processes that send two types of signals to their process group. There are four types of signal handling processes responsible for a particular type of signal. There is this monitoring process which waits for both the signals and then processes accordingly. When I run this program for a while, the monitoring process doesn't seem to pick up the signal as well as the signal handling process. I could see in the log that the signal is only being generated but not handled at all. My code is given below #include <cstdlib> #include <iostream> #include <iomanip> #include <unistd.h> #include <sys/types.h> #include <sys/wait.h> #include <sys/time.h> #include <signal.h> #include <unistd.h> #include <fcntl.h> #include <cstdio> #include <stdlib.h> #include <stdio.h> #include <pthread.h> using namespace std; double timestamp() { struct timeval tp; gettimeofday(&tp, NULL); return (double)tp.tv_sec + tp.tv_usec / 1000000.; } double getinterval() { srand(time(NULL)); int r = rand()%10 + 1; double s = (double)r/100; } int count; int count_1; int count_2; double time_1[10]; double time_2[10]; pid_t senders[1]; pid_t handlers[4]; pid_t reporter; void catcher(int sig) { printf("Signal catcher called for %d",sig); } int main(int argc, char *argv[]) { void signal_catcher_int(int); pid_t pid,w; int status; if(signal(SIGUSR1, SIG_IGN) == SIG_ERR) { perror("1"); return 1; } if(signal(SIGUSR2 ,SIG_IGN) == SIG_ERR) { perror("2"); return 2; } if(signal(SIGINT,signal_catcher_int) == SIG_ERR) { perror("3"); return 2; } //Registering the signal handler for(int i=0; i<4; i++) { if((pid = fork()) == 0) { cout << i << endl; //struct sigaction sigact; sigset_t sigset; int sig; int result = 0; sigemptyset(&sigset); if(i%2 == 0) { if(signal(SIGUSR2, SIG_IGN) == SIG_ERR) { perror("2"); return 2; } sigaddset(&sigset, SIGUSR1); sigprocmask(SIG_BLOCK, &sigset, NULL); } else { if(signal(SIGUSR1, SIG_IGN) == SIG_ERR) { perror("2"); return 2; } sigaddset(&sigset, SIGUSR2); sigprocmask(SIG_BLOCK, &sigset, NULL); } while(true) { int result = sigwait(&sigset, &sig); if(result == 0) { cout << "The caught signal is " << sig << endl; } } exit(0); } else { cout << "Registerd the handler " << pid << endl; handlers[i] = pid; } } //Registering the monitoring process if((pid = fork()) == 0) { sigset_t sigset; int sig; int result = 0; sigemptyset(&sigset); sigaddset(&sigset, SIGUSR1); sigaddset(&sigset, SIGUSR2); sigprocmask(SIG_BLOCK, &sigset, NULL); while(true) { int result = sigwait(&sigset, &sig); if(result == 0) { cout << "The monitored signal is " << sig << endl; } else { cout << "error" << endl; } } } else { reporter = pid; } sleep(3); //Registering the signal generator for(int i=0; i<1; i++) { if((pid = fork()) == 0) { if(signal(SIGUSR1, SIG_IGN) == SIG_ERR) { perror("1"); return 1; } if(signal(SIGUSR2, SIG_IGN) == SIG_ERR) { perror("2"); return 2; } srand(time(0)); while(true) { volatile int signal_id = rand()%2 + 1; cout << "Generating the signal " << signal_id << endl; if(signal_id == 1) { killpg(getpgid(getpid()), SIGUSR1); } else { killpg(getpgid(getpid()), SIGUSR2); } int r = rand()%10 + 1; double s = (double)r/100; sleep(s); } exit(0); } else { cout << "Registered the sender " << pid << endl; senders[i] = pid; } } while(w = wait(&status)) { cout << "Wait on PID " << w << endl; } } void signal_catcher_int(int the_sig) { //cout << "Handling the Ctrl C signal " << endl; for(int i=0; i<1; i++) { kill(senders[i],SIGKILL); } for(int i=0; i<4; i++) { kill(handlers[i],SIGKILL); } kill(reporter,SIGKILL); exit(3); } Any suggestions? Here is a sample of the output as well In the beginning Registerd the handler 9544 Registerd the handler 9545 1 Registerd the handler 9546 Registerd the handler 9547 2 3 0 Registered the sender 9550 Generating the signal 1 The caught signal is 10 The monitored signal is 10 The caught signal is 10 Generating the signal 1 The caught signal is 10 The monitored signal is 10 The caught signal is 10 Generating the signal 1 The caught signal is 10 The monitored signal is 10 The caught signal is 10 Generating the signal 1 The caught signal is 10 The monitored signal is 10 The caught signal is 10 Generating the signal 2 The caught signal is 12 The caught signal is 12 The monitored signal is 12 Generating the signal 2 Generating the signal 2 The caught signal is 12 The caught signal is 12 Generating the signal 1 The caught signal is 12 The monitored signal is 10 The monitored signal is 12 Generating the signal 1 Generating the signal 2 The caught signal is 12 Generating the signal 1 Generating the signal 2 10 The monitored signal is 10 The caught signal is 12 Generating the signal 1 The caught signal is 12 The monitored signal is GenThe caught signal is TheThe caught signal is 10 Generating the signal 2 Later on The monitored signal is GenThe monitored signal is 10 Generating the signal 1 Generating the signal 2 The caught signal is 10 The caught signal is 10 The caught signal is 10 The caught signal is 12 Generating the signal 1 Generating the signal 2 Generating the signal 1 Generating the signal 1 Generating the signal 2 Generating the signal 2 Generating the signal 2 Generating the signal 2 Generating the signal 2 Generating the signal 1 The caught signal is 12 The caught signal is 10 The caught signal is 10 Generating the signal 2 Generating the signal 1 Generating the signal 1 Generating the signal 2 Generating the signal 1 Generating the signal 2 Generating the signal 2 Generating the signal 2 Generating the signal 1 Generating the signal 2 Generating the signal 1 Generating the signal 2 Generating the signal 2 The caught signal is 10 Generating the signal 2 Generating the signal 1 Generating the signal 1 As you can see initially, the signal was generated and handled both by my signal handlers and monitoring processes. But later on the signal was generated a lot, but it was not quite processes in the same magnitude as before. Further I could see very less signal processing by the monitoring process Can anyone please provide some insights. What's going on?

  Read the article

• qwebview in pyside after packaged with pyinstaller goes wrong

  - by truease.com

  Here's my code import sys from PySide.QtCore import * from PySide.QtGui import * from PySide.QtWebKit import * from encodings import * from codecs import * class BrowserWindow( QWidget ): def __init__( self, parent=None ): QWidget.__init__( self, parent ) self.Setup() self.SetupEvent() def Setup( self ): self.setWindowTitle( u"Truease Speedy Browser" ) self.addr_input = QLineEdit() self.addr_go = QPushButton( "GO" ) self.addr_bar = QHBoxLayout() self.addr_bar.addWidget( self.addr_input ) self.addr_bar.addWidget( self.addr_go ) for attr in [ QWebSettings.AutoLoadImages, QWebSettings.JavascriptEnabled, QWebSettings.JavaEnabled, QWebSettings.PluginsEnabled, QWebSettings.JavascriptCanOpenWindows, QWebSettings.JavascriptCanAccessClipboard, QWebSettings.DeveloperExtrasEnabled, QWebSettings.SpatialNavigationEnabled, QWebSettings.OfflineStorageDatabaseEnabled, QWebSettings.OfflineWebApplicationCacheEnabled, QWebSettings.LocalStorageEnabled, QWebSettings.LocalStorageDatabaseEnabled, QWebSettings.LocalContentCanAccessRemoteUrls, QWebSettings.LocalContentCanAccessFileUrls, ]: QWebSettings.globalSettings().setAttribute( attr, True ) self.web_view = QWebView() self.web_view.load( "http://www.baidu.com" ) layout = QVBoxLayout() layout.addLayout( self.addr_bar ) layout.addWidget( self.web_view ) self.setLayout( layout ) def SetupEvent( self ): self.connect( self.addr_input, SIGNAL("editingFinished()"), self, SLOT("Load()"), ) self.connect( self.addr_go, SIGNAL("pressed()"), self, SLOT("Load()") ) self.connect( self.web_view, SIGNAL("urlChanged(const QUrl&)"), self, SLOT("SetURL()"), ) def Load( self, *args, **kwargs ): url = self.GetCleanedURL() if url != self.CurrentURL(): self.web_view.load( url ) def SetURL( self, *args, **kwargs ): self.addr_input.setText( self.CurrentURL() ) def GetCleanedURL( self ): url = self.addr_input.text().strip() if not url.startswith("http"): url = "http://" + url return url def CurrentURL( self ): url = self.web_view.url().toString() return url def Main(): app = QApplication( sys.argv ) widget = BrowserWindow() widget.show() return app.exec_() if __name__ == '__main__': sys.exit( Main() ) I works well when i using python browser.py. but it goes wrong after packaged with pyinstaller -w browser.py. it doesn't load images can only display correct text in utf-8 And this is the pyinstaller output: E:\true\wuk\app2>pyinstaller -w b.py 16 INFO: wrote E:\true\wuk\app2\b.spec 16 INFO: Testing for ability to set icons, version resources... 32 INFO: ... resource update available 32 INFO: UPX is not available. 46 INFO: Processing hook hook-os 141 INFO: Processing hook hook-time 157 INFO: Processing hook hook-cPickle 218 INFO: Processing hook hook-_sre 312 INFO: Processing hook hook-cStringIO 407 INFO: Processing hook hook-encodings 421 INFO: Processing hook hook-codecs 750 INFO: Processing hook hook-httplib 750 INFO: Processing hook hook-email 843 INFO: Processing hook hook-email.message 1046 WARNING: library python%s%s required via ctypes not found 1171 INFO: Extending PYTHONPATH with E:\true\wuk\app2 1171 INFO: checking Analysis 1171 INFO: building because b.py changed 1171 INFO: running Analysis out00-Analysis.toc 1171 INFO: Adding Microsoft.VC90.CRT to dependent assemblies of final executable 1171 INFO: Searching for assembly x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww ... 1171 INFO: Found manifest C:\WINDOWS\WinSxS\Manifests\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375.manifest 1187 INFO: Searching for file msvcr90.dll 1187 INFO: Found file C:\WINDOWS\WinSxS\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375\msvcr90.dll 1187 INFO: Searching for file msvcp90.dll 1187 INFO: Found file C:\WINDOWS\WinSxS\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375\msvcp90.dll 1187 INFO: Searching for file msvcm90.dll 1187 INFO: Found file C:\WINDOWS\WinSxS\x86_Microsoft.VC90.CRT_1fc8b3b9a1e18e3b_9.0.21022.8_x-ww_d08d0375\msvcm90.dll 1266 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\_pyi_bootstrap.py 1266 INFO: Processing hook hook-os 1282 INFO: Processing hook hook-site 1296 INFO: Processing hook hook-encodings 1391 INFO: Processing hook hook-time 1407 INFO: Processing hook hook-cPickle 1468 INFO: Processing hook hook-_sre 1578 INFO: Processing hook hook-cStringIO 1671 INFO: Processing hook hook-codecs 2016 INFO: Processing hook hook-httplib 2016 INFO: Processing hook hook-email 2109 INFO: Processing hook hook-email.message 2312 WARNING: library python%s%s required via ctypes not found 2468 INFO: Processing hook hook-pydoc 2516 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_importers.py 2609 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_archive.py 2687 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_carchive.py 2782 INFO: Analyzing D:\Applications\Python\lib\site-packages\pyinstaller-2.1-py2.7.egg\PyInstaller\loader\pyi_os_path.py 2782 INFO: Analyzing b.py 2796 INFO: Processing hook hook-PySide 2875 INFO: Hidden import 'codecs' has been found otherwise 2875 INFO: Hidden import 'encodings' has been found otherwise 2875 INFO: Looking for run-time hooks 7766 INFO: Using Python library C:\WINDOWS\system32\python27.dll 7796 INFO: E:\true\wuk\app2\build\b\out00-Analysis.toc no change! 7796 INFO: checking PYZ 7812 INFO: checking PKG 7812 INFO: building because E:\true\wuk\app2\build\b\b.exe.manifest changed 7812 INFO: building PKG (CArchive) out00-PKG.pkg 7828 INFO: checking EXE 7843 INFO: rebuilding out00-EXE.toc because pkg is more recent 7843 INFO: building EXE from out00-EXE.toc 7843 INFO: Appending archive to EXE E:\true\wuk\app2\build\b\b.exe 7843 INFO: checking COLLECT 7843 INFO: building COLLECT out00-COLLECT.toc Use pyinstaller browser.py, and in the console window i got QFont::setPixelSize: Pixel size <= 0 (0) QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QSslSocket: cannot call unresolved function SSLv23_client_method QSslSocket: cannot call unresolved function SSL_CTX_new QSslSocket: cannot call unresolved function SSL_library_init QSslSocket: cannot call unresolved function ERR_get_error QFont::setPixelSize: Pixel size <= 0 (0)

  Read the article

• ssh permission denied

  - by Gitmo

  I am trying to ssh into a remote machine and I get the following debug messages: debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to xxx.xxx.x.xx [xxx.xxx.xx.x] port 22. debug1: Connection established. debug3: Not a RSA1 key file /home/hadoop/.ssh/id_rsa. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/hadoop/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-6ubuntu2 debug1: match: OpenSSH_5.1p1 Debian-6ubuntu2 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: none,[email protected],zlib debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,arcfour128,arcfour256,arcfour,aes192-cbc,aes256-cbc,[email protected],aes128-ctr,aes192-ctr,aes256-ctr debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-cbc hmac-md5 none debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug2: dh_gen_key: priv key bits set: 128/256 debug2: bits set: 511/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: check_host_in_hostfile: filename /home/hadoop/.ssh/known_hosts debug3: check_host_in_hostfile: match line 20 debug1: Host '192.168.1.63' is known and matches the RSA host key. debug1: Found key in /home/hadoop/.ssh/known_hosts:20 debug2: bits set: 511/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/hadoop/.ssh/id_rsa (0x241c110) debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/hadoop/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password debug2: we did not send a packet, disable method debug1: No more authentication methods to try. Permission denied (publickey,password). What seems to be the problem?? I have tried everything, this is driving me nuts.

  Read the article

• Can't import my module when start my twisted application under root

  - by kepkin

  Here is absolutely minimal application so you could try to reproduce it on your machine. Having two files for example in /home/aln/tmp/tw_test: server.tac MyLib.py MyLib.py class Solver(object): def solve(self): """ do extremely complex stuff here """ print "Hello from solve" server.tac #!/usr/bin/python import MyLib from twisted.application import internet, service from twisted.internet import protocol, reactor, defer, utils, threads from twisted.protocols import basic class MyProtocol(basic.LineReceiver): def lineReceived(self, line): if line=="new job": self.transport.write("started a job" + '\r\n') self.factory.run_defered() class MyFactory(protocol.ServerFactory, MyLib.Solver): protocol = MyProtocol def run_defered_helper(self): self.solve() def run_defered(self): d = threads.deferToThread(self.run_defered_helper) application = service.Application('MyApplication') factory = MyFactory() internet.TCPServer(1079, factory).setServiceParent(service.IServiceCollection(application)) Everything works fine when I start it under non-root user. aln@aln-laptop:tw_test$ twistd -ny server.tac 2010-03-03 22:42:55+0300 [-] Log opened. 2010-03-03 22:42:55+0300 [-] twistd 8.2.0 (/usr/bin/python 2.6.4) starting up. 2010-03-03 22:42:55+0300 [-] reactor class: twisted.internet.selectreactor.SelectReactor. 2010-03-03 22:42:55+0300 [-] <class 'MyFactory'> starting on 1079 2010-03-03 22:42:55+0300 [-] Starting factory <MyFactory object at 0x2d5ea50> 2010-03-03 22:42:59+0300 [MyProtocol,0,127.0.0.1] Hello from solve ^C2010-03-03 22:43:01+0300 [-] Received SIGINT, shutting down. 2010-03-03 22:43:01+0300 [-] (Port 1079 Closed) 2010-03-03 22:43:01+0300 [-] Stopping factory <MyFactory object at 0x2d5ea50> 2010-03-03 22:43:01+0300 [-] Main loop terminated. 2010-03-03 22:43:02+0300 [-] Server Shut Down. But if try to start it under root (which is going to happen in my real application) I receive the following exception: aln@aln-laptop:tw_test$ sudo twistd -ny server.tac [sudo] password for aln: Traceback (most recent call last): File "/usr/lib/python2.6/dist-packages/twisted/application/app.py", line 694, in run runApp(config) File "/usr/lib/python2.6/dist-packages/twisted/scripts/twistd.py", line 23, in runApp _SomeApplicationRunner(config).run() File "/usr/lib/python2.6/dist-packages/twisted/application/app.py", line 411, in run self.application = self.createOrGetApplication() File "/usr/lib/python2.6/dist-packages/twisted/application/app.py", line 494, in createOrGetApplication application = getApplication(self.config, passphrase) --- <exception caught here> --- File "/usr/lib/python2.6/dist-packages/twisted/application/app.py", line 505, in getApplication application = service.loadApplication(filename, style, passphrase) File "/usr/lib/python2.6/dist-packages/twisted/application/service.py", line 390, in loadApplication application = sob.loadValueFromFile(filename, 'application', passphrase) File "/usr/lib/python2.6/dist-packages/twisted/persisted/sob.py", line 215, in loadValueFromFile exec fileObj in d, d File "server.tac", line 2, in <module> import MyLib exceptions.ImportError: No module named MyLib Failed to load application: No module named MyLib If I try to load MyLib module in the python intepreter under root, it works fine: aln@aln-laptop:tw_test$ sudo python Python 2.6.4 (r264:75706, Dec 7 2009, 18:43:55) [GCC 4.4.1] on linux2 Type "help", "copyright", "credits" or "license" for more information. >>> import MyLib >>> import sys >>> print(sys.path) ['', '/usr/lib/python2.6', '/usr/lib/python2.6/plat-linux2', '/usr/lib/python2.6/lib-tk', '/usr/lib/python2.6/lib-old', '/usr/lib/python2.6/lib-dynload', '/usr/lib/python2.6/dist-packages', '/usr/lib/python2.6/dist-packages/PIL', '/usr/lib/python2.6/dist-packages/gst-0.10', '/usr/lib/pymodules/python2.6', '/usr/lib/python2.6/dist-packages/gtk-2.0', '/usr/lib/pymodules/python2.6/gtk-2.0', '/usr/local/lib/python2.6/dist-packages'] >>> sys.path is absolutely the same for aln user. I tried sudo -E too. Any suggestions?

  Read the article

• One letter game problem?

  - by Alex K

  Recently at a job interview I was given the following problem: Write a script capable of running on the command line as python It should take in two words on the command line (or optionally if you'd prefer it can query the user to supply the two words via the console). Given those two words: a. Ensure they are of equal length b. Ensure they are both words present in the dictionary of valid words in the English language that you downloaded. If so compute whether you can reach the second word from the first by a series of steps as follows a. You can change one letter at a time b. Each time you change a letter the resulting word must also exist in the dictionary c. You cannot add or remove letters If the two words are reachable, the script should print out the path which leads as a single, shortest path from one word to the other. You can /usr/share/dict/words for your dictionary of words. My solution consisted of using breadth first search to find a shortest path between two words. But apparently that wasn't good enough to get the job :( Would you guys know what I could have done wrong? Thank you so much. import collections import functools import re def time_func(func): import time def wrapper(*args, **kwargs): start = time.time() res = func(*args, **kwargs) timed = time.time() - start setattr(wrapper, 'time_taken', timed) return res functools.update_wrapper(wrapper, func) return wrapper class OneLetterGame: def __init__(self, dict_path): self.dict_path = dict_path self.words = set() def run(self, start_word, end_word): '''Runs the one letter game with the given start and end words. ''' assert len(start_word) == len(end_word), \ 'Start word and end word must of the same length.' self.read_dict(len(start_word)) path = self.shortest_path(start_word, end_word) if not path: print 'There is no path between %s and %s (took %.2f sec.)' % ( start_word, end_word, find_shortest_path.time_taken) else: print 'The shortest path (found in %.2f sec.) is:\n=> %s' % ( self.shortest_path.time_taken, ' -- '.join(path)) def _bfs(self, start): '''Implementation of breadth first search as a generator. The portion of the graph to explore is given on demand using get_neighboors. Care was taken so that a vertex / node is explored only once. ''' queue = collections.deque([(None, start)]) inqueue = set([start]) while queue: parent, node = queue.popleft() yield parent, node new = set(self.get_neighbours(node)) - inqueue inqueue = inqueue | new queue.extend([(node, child) for child in new]) @time_func def shortest_path(self, start, end): '''Returns the shortest path from start to end using bfs. ''' assert start in self.words, 'Start word not in dictionnary.' assert end in self.words, 'End word not in dictionnary.' paths = {None: []} for parent, child in self._bfs(start): paths[child] = paths[parent] + [child] if child == end: return paths[child] return None def get_neighbours(self, word): '''Gets every word one letter away from the a given word. We do not keep these words in memory because bfs accesses a given vertex only once. ''' neighbours = [] p_word = ['^' + word[0:i] + '\w' + word[i+1:] + '$' for i, w in enumerate(word)] p_word = '|'.join(p_word) for w in self.words: if w != word and re.match(p_word, w, re.I|re.U): neighbours += [w] return neighbours def read_dict(self, size): '''Loads every word of a specific size from the dictionnary into memory. ''' for l in open(self.dict_path): l = l.decode('latin-1').strip().lower() if len(l) == size: self.words.add(l) if __name__ == '__main__': import sys if len(sys.argv) not in [3, 4]: print 'Usage: python one_letter_game.py start_word end_word' else: g = OneLetterGame(dict_path = '/usr/share/dict/words') try: g.run(*sys.argv[1:]) except AssertionError, e: print e

  Read the article

• Problem in transfering file from server to client using C sockets

  - by coolrockers2007

  I want to ask, why I cannot transfer file from server to client? When I start to send the file from server, the client side program will have problem. So, I spend some times to check the code, But I still cannot find out the problem Can anyone point out the problem for me? CLIENTFILE.C #include stdio.h #include stdlib.h #include time.h #include netinet/in.h #include fcntl.h #include sys/types.h #include string.h #include stdarg.h #define PORT 5678 #define MLEN 1000 int main(int argc, char *argv []) { int sockfd; int number,message; char outbuff[MLEN],inbuff[MLEN]; //char PWD_buffer[_MAX_PATH]; struct sockaddr_in servaddr; FILE *fp; int numbytes; char buf[2048]; if (argc != 2) fprintf(stderr, "error"); if ( (sockfd = socket(AF_INET, SOCK_STREAM, 0)) < 0) fprintf(stderr, "socket error"); memset(&servaddr, 0, sizeof(servaddr)); servaddr.sin_family = AF_INET; servaddr.sin_port = htons(PORT); if (connect(sockfd, (struct sockaddr *) &servaddr, sizeof(servaddr)) < 0) fprintf(stderr, "connect error"); if ( (fp = fopen("/home/na/nall9047/write.txt", "w")) == NULL){ perror("fopen"); exit(1); } printf("Still NO PROBLEM!\n"); //Receive file from server while(1){ numbytes = read(sockfd, buf, sizeof(buf)); printf("read %d bytes, ", numbytes); if(numbytes == 0){ printf("\n"); break; } numbytes = fwrite(buf, sizeof(char), numbytes, fp); printf("fwrite %d bytes\n", numbytes); } fclose(fp); close(sockfd); return 0; } SERVERFILE.C #include stdio.h #include fcntl.h #include stdlib.h #include time.h #include string.h #include netinet/in.h #include errno.h #include sys/types.h #include sys/socket.h #includ estdarg.h #define PORT 5678 #define MLEN 1000 int main(int argc, char *argv []) { int listenfd, connfd; int number, message, numbytes; int h, i, j, alen; int nread; struct sockaddr_in servaddr; struct sockaddr_in cliaddr; FILE *in_file, *out_file, *fp; char buf[4096]; listenfd = socket(AF_INET, SOCK_STREAM, 0); if (listenfd < 0) fprintf(stderr,"listen error") ; memset(&servaddr, 0, sizeof(servaddr)); servaddr.sin_family = AF_INET; servaddr.sin_addr.s_addr = htonl(INADDR_ANY); servaddr.sin_port = htons(PORT); if (bind(listenfd, (struct sockaddr *) &servaddr, sizeof(servaddr)) < 0) fprintf(stderr,"bind error") ; alen = sizeof(struct sockaddr); connfd = accept(listenfd, (struct sockaddr *) &cliaddr, &alen); if (connfd < 0) fprintf(stderr,"error connecting") ; printf("accept one client from %s!\n", inet_ntoa(cliaddr.sin_addr)); fp = fopen ("/home/na/nall9047/read.txt", "r"); // open file stored in server if (fp == NULL) { printf("\nfile NOT exist"); } //Sending file while(!feof(fp)){ numbytes = fread(buf, sizeof(char), sizeof(buf), fp); printf("fread %d bytes, ", numbytes); numbytes = write(connfd, buf, numbytes); printf("Sending %d bytes\n",numbytes); } fclose (fp); close(listenfd); close(connfd); return 0; }

  Read the article

• multiple timer to one process (without linking to rt)

  - by Richard

  Hi, is there any way to register multiple timer to a single process? I have tried following code, yet without success. (Use "gcc -lrt" to compile it...). Program output nothing, which should atleast print "test". Is it possibly due to the dependence to linking to rt? #define TT_SIGUSR1 (SIGRTMAX) #define TT_SIGUSR2 (SIGRTMAX - 1) #define TIME_INTERVAL_1 1 #define TIME_INTERVAL_2 2 #include <signal.h> #include <time.h> #include <stdio.h> #include <unistd.h> #include <linux/unistd.h> #include <sys/syscall.h> #include <sys/time.h> #include <sys/types.h> #include <sched.h> #include <signal.h> #include <setjmp.h> #include <errno.h> #include <assert.h> timer_t create_timer(int signo) { timer_t timerid; struct sigevent se; se.sigev_signo = signo; if (timer_create(CLOCK_REALTIME, &se, &timerid) == -1) { fprintf(stderr, "Failed to create timer\n"); exit(-1); } return timerid; } void set_timer(timer_t timerid, int seconds) { struct itimerspec timervals; timervals.it_value.tv_sec = seconds; timervals.it_value.tv_nsec = 0; timervals.it_interval.tv_sec = seconds; timervals.it_interval.tv_nsec = 0; if (timer_settime(timerid, 0, &timervals, NULL) == -1) { fprintf(stderr, "Failed to start timer\n"); exit(-1); } return; } void install_sighandler2(int signo, void(*handler)(int)) { struct sigaction sigact; sigemptyset(&sigact.sa_mask); sigact.sa_flags = SA_SIGINFO; //register the Signal Handler sigact.sa_sigaction = handler; // Set up sigaction to catch signal first timer if (sigaction(signo, &sigact, NULL) == -1) { printf("sigaction failed"); return -1; } } void install_sighandler(int signo, void(*handler)(int)) { sigset_t set; struct sigaction act; /* Setup the handler */ act.sa_handler = handler; act.sa_flags = SA_RESTART; sigaction(signo, &act, 0); /* Unblock the signal */ sigemptyset(&set); sigaddset(&set, signo); sigprocmask(SIG_UNBLOCK, &set, NULL); return; } void signal_handler(int signo) { printf("receiving sig %d", signo); } int main() { printf("test"); timer_t timer1 = create_timer(TT_SIGUSR1); timer_t timer2 = create_timer(TT_SIGUSR2); set_timer(timer1, TIME_INTERVAL_1); set_timer(timer2, TIME_INTERVAL_2); install_sighandler2(TT_SIGUSR1, signal_handler); install_sighandler(TT_SIGUSR2, signal_handler); while (1) ; return 0; }

  Read the article

• xts error - order.by requires an appropriate time-based object

  - by Samo

  I can not resolve why error in simple creation of xts object xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE)) Error in xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE)) : order.by requires an appropriate time-based object appeared while this was working perfectly 14 days ago when I last used the same code (since then the only difference is that TICK.NYSE grow in length since data was added since then). More details below: > Sys.getenv("TZ") [1] "EST" > tail(xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE))) Error in xts(rep(0, NROW(TICK.NYSE)), order.by = index(TICK.NYSE)) : order.by requires an appropriate time-based object > class(index(TICK.NYSE["T09:30/T09:31"])) [1] "POSIXct" > tail(xts(rep(0, NROW(tail(TICK.NYSE))), order.by = index(tail(TICK.NYSE)))) Error in xts(rep(0, NROW(tail(TICK.NYSE))), order.by = index(tail(TICK.NYSE))) : order.by requires an appropriate time-based object > tail(TICK.NYSE) TICK-NYSE.Open TICK-NYSE.High TICK-NYSE.Low TICK-NYSE.Close 2012-03-15 14:54:00 -278 -89 -299 -89 2012-03-15 14:55:00 -89 427 -89 201 2012-03-15 14:56:00 201 318 30 234 2012-03-15 14:57:00 234 242 -222 -64 2012-03-15 14:58:00 -64 346 -82 346 2012-03-15 14:59:00 346 525 36 525 TICK-NYSE.Volume TICK-NYSE.WAP TICK-NYSE.hasGaps 2012-03-15 14:54:00 0 0 0 2012-03-15 14:55:00 0 0 0 2012-03-15 14:56:00 0 0 0 2012-03-15 14:57:00 0 0 0 2012-03-15 14:58:00 0 0 0 2012-03-15 14:59:00 0 0 0 TICK-NYSE.Count 2012-03-15 14:54:00 31 2012-03-15 14:55:00 31 2012-03-15 14:56:00 31 2012-03-15 14:57:00 31 2012-03-15 14:58:00 29 2012-03-15 14:59:00 30 > str(TICK.NYSE) An ‘xts’ object from 2011-01-18 09:30:00 to 2012-03-15 14:59:00 containing: Data: num [1:114090, 1:8] -5 -144 24 -148 -184 -77 20 121 111 -60 ... - attr(*, "dimnames")=List of 2 ..$ : NULL ..$ : chr [1:8] "TICK-NYSE.Open" "TICK-NYSE.High" "TICK-NYSE.Low" "TICK-NYSE.Close" ... Indexed by objects of class: [POSIXct,POSIXt] TZ: xts Attributes: List of 4 $ from : chr "20110119 23:59:59" $ to : chr "20110124 23:59:59" $ src : chr "IB" $ updated: POSIXct[1:1], format: "2012-01-19 02:34:52" > str(index(TICK.NYSE)) Class 'POSIXct' atomic [1:114090] 1.3e+09 1.3e+09 1.3e+09 1.3e+09 1.3e+09 ... ..- attr(*, "tzone")= chr "" ..- attr(*, "tclass")= chr [1:2] "POSIXct" "POSIXt" > Sys.getenv("TZ") [1] "EST" > tail(index(TICK.NYSE)) [1] "2012-03-15 14:54:00 EST" "2012-03-15 14:55:00 EST" [3] "2012-03-15 14:56:00 EST" "2012-03-15 14:57:00 EST" [5] "2012-03-15 14:58:00 EST" "2012-03-15 14:59:00 EST" > head(index(TICK.NYSE)) [1] "2011-01-18 09:30:00 EST" "2011-01-18 09:31:00 EST" [3] "2011-01-18 09:32:00 EST" "2011-01-18 09:33:00 EST" [5] "2011-01-18 09:34:00 EST" "2011-01-18 09:35:00 EST" > Sys.info() sysname "Linux" release "3.0.0-16-generic" version "#28-Ubuntu SMP Fri Jan 27 17:44:39 UTC 2012" > sessionInfo() R version 2.14.1 (2011-12-22) Platform: x86_64-pc-linux-gnu (64-bit) locale: [1] LC_CTYPE=en_US.UTF-8 LC_NUMERIC=C [3] LC_TIME=en_US.UTF-8 LC_COLLATE=en_US.UTF-8 [5] LC_MONETARY=en_US.UTF-8 LC_MESSAGES=en_US.UTF-8 [7] LC_PAPER=en_US.UTF-8 LC_NAME=en_US.UTF-8 [9] LC_ADDRESS=en_US.UTF-8 LC_TELEPHONE=en_US.UTF-8 [11] LC_MEASUREMENT=en_US.UTF-8 LC_IDENTIFICATION=en_US.UTF-8 attached base packages: [1] stats graphics grDevices utils datasets methods base other attached packages: [1] lattice_0.20-0 multicore_0.1-7 [3] doSNOW_1.0.5 snow_0.3-8 [5] doRedis_1.0.4 rredis_1.6.3 [7] foreach_1.3.2 codetools_0.2-8 [9] iterators_1.0.5 PerformanceAnalytics_1.0.3.3 [11] quantstrat_0.6.1 blotter_0.8.4 [13] twsInstrument_1.3-3 FinancialInstrument_0.10.6 [15] IBrokers_0.9-6 quantmod_0.3-18 [17] TTR_0.21-0 xts_0.8-4 [19] Defaults_1.1-1 strucchange_1.4-6 [21] sandwich_2.2-8 zoo_1.7-7 [23] rj_1.0.2-5 loaded via a namespace (and not attached): [1] grid_2.14.1 tools_2.14.1 > dput(tail(TICK.NYSE)) structure(c(-385, -213, -42, -334, -233, -111, -121, 20, -14, -125, -73, 265, -583, -269, -426, -520, -443, -440, -213, -42, -334, -233, -111, 119, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 31, 31, 30, 30, 31, 31), class = c("xts", "zoo" ), .indexCLASS = c("POSIXct", "POSIXt"), .indexTZ = "", from = "20110119 23:59:59", to = "20110124 23:59:59", src = "IB", updated = structure(1326958492.96405, class = c("POSIXct", "POSIXt")), index = structure(c(1331927640, 1331927700, 1331927760, 1331927820, 1331927880, 1331927940), tzone = "", tclass = c("POSIXct", "POSIXt")), .Dim = c(6L, 8L), .Dimnames = list(NULL, c("TICK-NYSE.Open", "TICK-NYSE.High", "TICK-NYSE.Low", "TICK-NYSE.Close", "TICK-NYSE.Volume", "TICK-NYSE.WAP", "TICK-NYSE.hasGaps", "TICK-NYSE.Count")))

  Read the article

• WD MBWE II (White Strip Light) 2TB - unable to access data

  - by user210477

  I have a WD MBWE II (White Strip Light) 2TB - (WD20000H2NC-00) Was working fine until a few days ago. I guess there was a power failure and after that I am unable to access the 'Public' or the 'Download' folder anymore. I have been searching for answers everywhere but came up empty handed. Web GUI still works, SSH works. I hooked up both the drives on my PC and UFS Explorer sees the drive. But so far I am unable to retrieve any of my data. I do not remember what RAID setting I used when I first got the drive. I can see from GUI that it is set as "Stripe". The drive contains 10 years of family pictures which I really do not want to loose. Sadly and stupidly, I didn't even keep a backup of this drive. Can somebody please help or point me in the right direction. Thank you in advance for your help. Disk Utility on Ubuntu reports 1405 bad sectors on one drive. How can I retrieve my data? Please help. Logs below: ~ # mdadm --detail /dev/md[012345678] /dev/md0: Version : 0.90 Creation Time : Wed Jul 15 08:36:17 2009 Raid Level : raid1 Array Size : 1959872 (1914.26 MiB 2006.91 MB) Used Dev Size : 1959872 (1914.26 MiB 2006.91 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:53:29 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 04f7a661:98983b3b:26b29e4f:9b646adb Events : 0.266 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 /dev/md1: Version : 0.90 Creation Time : Wed Jul 15 08:36:18 2009 Raid Level : raid1 Array Size : 256896 (250.92 MiB 263.06 MB) Used Dev Size : 256896 (250.92 MiB 263.06 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Oct 30 22:08:21 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : aaa7b859:c475312d:efc5a766:6526b867 Events : 0.10 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 8 18 1 active sync /dev/sdb2 /dev/md2: Version : 0.90 Creation Time : Sat Sep 25 10:01:26 2010 Raid Level : raid0 Array Size : 1947045760 (1856.85 GiB 1993.77 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:30:53 2013 State : active Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K UUID : 01dae60a:6831077b:77f74530:8680c183 Events : 0.97 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 8 20 1 active sync /dev/sdb4 /dev/md3: Version : 0.90 Creation Time : Wed Jul 15 08:36:18 2009 Raid Level : raid1 Array Size : 987904 (964.91 MiB 1011.61 MB) Used Dev Size : 987904 (964.91 MiB 1011.61 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:26:33 2013 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 3f4099f2:72e6171b:5ba962fd:48464a62 Events : 0.54 Number Major Minor RaidDevice State 0 8 3 0 active sync /dev/sda3 1 8 19 1 active sync /dev/sdb3 mdadm: md device /dev/md4 does not appear to be active. mdadm: md device /dev/md5 does not appear to be active. mdadm: md device /dev/md6 does not appear to be active. mdadm: md device /dev/md7 does not appear to be active. mdadm: md device /dev/md8 does not appear to be active. ~ # cat /etc/mtab securityfs /sys/kernel/security securityfs rw 0 0 /dev/md2 /DataVolume xfs rw,usrquota 0 0 /dev/md4 /ExtendVolume xfs rw,usrquota 0 0 ~ # df -k Filesystem 1k-blocks Used Available Use% Mounted on /dev/md0 1929044 145092 1685960 8% / /dev/md3 972344 123452 799500 13% /var /dev/ram0 63412 20 63392 0% /mnt/ram ~ # mdadm -D /dev/md2 /dev/md2: Version : 0.90 Creation Time : Sat Sep 25 10:01:26 2010 Raid Level : raid0 Array Size : 1947045760 (1856.85 GiB 1993.77 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Fri Nov 1 13:30:53 2013 State : active Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Chunk Size : 64K UUID : 01dae60a:6831077b:77f74530:8680c183 Events : 0.97 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 8 20 1 active sync /dev/sdb4 ~ # mdadm -D /dev/md4 mdadm: md device /dev/md4 does not appear to be active. ~ # mount /dev/root on / type ext3 (rw,noatime,data=ordered) proc on /proc type proc (rw) sys on /sys type sysfs (rw) /dev/pts on /dev/pts type devpts (rw) securityfs on /sys/kernel/security type securityfs (rw) /dev/md3 on /var type ext3 (rw,noatime,data=ordered) /dev/ram0 on /mnt/ram type tmpfs (rw) ~ # cat /var/log/messages Oct 29 18:04:50 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 29 18:04:59 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 29 18:04:59 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 29 18:17:45 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 29 18:17:53 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 29 18:17:53 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 00:50:11 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 00:50:19 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 00:50:19 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 16:29:47 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 16:30:00 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 16:30:00 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 18:27:22 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 18:27:30 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 18:27:30 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 19:06:03 shmotashNAS daemon.warn wixEvent[3462]: Network Link - NIC 1 link is down. Oct 30 19:06:10 shmotashNAS daemon.info wixEvent[3462]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 19:06:10 shmotashNAS daemon.info wixEvent[3462]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 19:14:58 shmotashNAS daemon.warn wixEvent[3462]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 30 19:20:05 shmotashNAS daemon.alert wixEvent[3462]: Thermal Alarm - System temperature exceeded threshold.(66 degrees) Oct 30 19:58:29 shmotashNAS daemon.alert wixEvent[3462]: HDD SMART - HDD 1 SMART Health Status: Failed. Oct 30 22:05:39 shmotashNAS daemon.info init: Starting pid 13043, console /dev/null: '/usr/bin/killall' Oct 30 22:05:39 shmotashNAS syslog.info System log daemon exiting. Oct 30 22:08:09 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 30 22:08:09 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:08:19 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:08:25 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:08:37 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:08:44 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:08:46 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:30 - 22:08:46 [Version 01.09.00.96] ++++++++++++++ Oct 30 22:08:46 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 30 22:08:46 shmotashNAS syslog.info miocrawler: ****** database does not exist. ret = -1, creating path Oct 30 22:08:49 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 30 22:08:50 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 30 22:08:51 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 30 22:08:51 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 30 22:08:51 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 30 22:08:52 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 30 22:08:52 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:08:57 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:09:10 shmotashNAS daemon.info init: Starting pid 4605, console /dev/null: '/bin/touch' Oct 30 22:09:10 shmotashNAS daemon.info init: Starting pid 4607, console /dev/ttyS0: '/sbin/getty' Oct 30 22:09:10 shmotashNAS daemon.info wixEvent[3557]: System Startup - System startup. Oct 30 22:09:16 shmotashNAS daemon.warn wixEvent[3557]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 30 22:14:14 shmotashNAS daemon.warn wixEvent[3557]: Network Link - NIC 1 link is down. Oct 30 22:14:21 shmotashNAS daemon.info wixEvent[3557]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:14:21 shmotashNAS daemon.info wixEvent[3557]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:29:36 shmotashNAS daemon.warn wixEvent[3557]: System Reboot - System will reboot. Oct 30 22:29:40 shmotashNAS daemon.info init: Starting pid 5974, console /dev/null: '/usr/bin/killall' Oct 30 22:29:40 shmotashNAS syslog.info System log daemon exiting. Oct 30 22:47:56 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 30 22:47:56 shmotashNAS daemon.warn wixEvent[3461]: Network Link - NIC 1 link is down. Oct 30 22:48:02 shmotashNAS daemon.info wixEvent[3461]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 22:48:02 shmotashNAS daemon.info wixEvent[3461]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 22:48:09 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:30 - 22:48:09 [Version 01.09.00.96] ++++++++++++++ Oct 30 22:48:09 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 30 22:48:09 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Oct 30 22:48:10 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 30 22:48:10 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 30 22:48:11 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 30 22:48:27 shmotashNAS daemon.info init: Starting pid 4079, console /dev/null: '/bin/touch' Oct 30 22:48:27 shmotashNAS daemon.info init: Starting pid 4080, console /dev/ttyS0: '/sbin/getty' Oct 30 22:48:28 shmotashNAS daemon.info wixEvent[3461]: System Startup - System startup. Oct 30 22:49:01 shmotashNAS daemon.warn wixEvent[3461]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 30 23:51:11 shmotashNAS daemon.warn wixEvent[3461]: System Reboot - System will reboot. Oct 30 23:51:16 shmotashNAS daemon.info init: Starting pid 6498, console /dev/null: '/usr/bin/killall' Oct 30 23:51:16 shmotashNAS syslog.info System log daemon exiting. Oct 30 23:54:19 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 30 23:55:37 shmotashNAS daemon.info wixEvent[3476]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 30 23:55:37 shmotashNAS daemon.info wixEvent[3476]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 30 23:55:44 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:30 - 23:55:44 [Version 01.09.00.96] ++++++++++++++ Oct 30 23:55:44 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 30 23:55:44 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Oct 30 23:55:45 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 30 23:55:45 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 30 23:55:46 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 30 23:55:58 shmotashNAS daemon.info init: Starting pid 4115, console /dev/null: '/bin/touch' Oct 30 23:55:58 shmotashNAS daemon.info init: Starting pid 4116, console /dev/ttyS0: '/sbin/getty' Oct 30 23:55:58 shmotashNAS daemon.info wixEvent[3476]: System Startup - System startup. Oct 30 23:56:33 shmotashNAS daemon.warn wixEvent[3476]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 31 00:29:14 shmotashNAS auth.info sshd[5409]: Server listening on 0.0.0.0 port 22. Oct 31 00:31:25 shmotashNAS auth.info sshd[5486]: Accepted password for root from 192.168.1.100 port 50785 ssh2 Oct 31 00:33:44 shmotashNAS auth.info sshd[5565]: Accepted password for root from 192.168.1.100 port 50817 ssh2 Oct 31 00:36:39 shmotashNAS daemon.info init: Starting pid 5680, console /dev/null: '/usr/bin/killall' Oct 31 00:36:39 shmotashNAS syslog.info System log daemon exiting. Oct 31 00:40:44 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Oct 31 00:40:51 shmotashNAS daemon.info wixEvent[3464]: Network Link - NIC 1 link is up 100 Mbps full duplex. Oct 31 00:40:51 shmotashNAS daemon.info wixEvent[3464]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:10:31 - 00:41:00 [Version 01.09.00.96] ++++++++++++++ Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: mc_db_init ... Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Oct 31 00:41:00 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Oct 31 00:41:01 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === inotify init done. Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Oct 31 00:41:02 shmotashNAS syslog.info miocrawler: === Walking directory done. Oct 31 00:41:14 shmotashNAS daemon.info init: Starting pid 4101, console /dev/null: '/bin/touch' Oct 31 00:41:14 shmotashNAS daemon.info init: Starting pid 4102, console /dev/ttyS0: '/sbin/getty' Oct 31 00:41:15 shmotashNAS daemon.info wixEvent[3464]: System Startup - System startup. Oct 31 00:41:47 shmotashNAS daemon.warn wixEvent[3464]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Oct 31 01:13:19 shmotashNAS daemon.info init: Starting pid 5385, console /dev/null: '/usr/bin/killall' Oct 31 01:13:19 shmotashNAS syslog.info System log daemon exiting. Nov 1 13:26:25 shmotashNAS syslog.info syslogd started: BusyBox v1.1.1 Nov 1 13:26:32 shmotashNAS daemon.info wixEvent[3471]: Network Link - NIC 1 link is up 100 Mbps full duplex. Nov 1 13:26:32 shmotashNAS daemon.info wixEvent[3471]: Network IP Address - NIC 1 use static IP address 192.168.1.102 Nov 1 13:26:38 shmotashNAS syslog.info miocrawler: +++++++++++++++ START OF ./miocrawler at 2013:11:01 - 13:26:38 [Version 01.09.00.96] ++++++++++++++ Nov 1 13:26:38 shmotashNAS syslog.info miocrawler: mc_db_init ... Nov 1 13:26:38 shmotashNAS syslog.info miocrawler: ++++++++ database exists: ret = 0 Nov 1 13:26:39 shmotashNAS syslog.info miocrawler: === mc_db_init ...Done. Nov 1 13:26:39 shmotashNAS syslog.info miocrawler: mcUtilsInit() Creating free queue pool Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === mcUtilsInit() Done. Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === inotify init done. Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: mc_trans_updater_init() ... Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === mc_trans_updater_init() ...Done. Nov 1 13:26:40 shmotashNAS syslog.info miocrawler: === Walking directory done. Nov 1 13:26:52 shmotashNAS daemon.info init: Starting pid 4078, console /dev/null: '/bin/touch' Nov 1 13:26:52 shmotashNAS daemon.info init: Starting pid 4079, console /dev/ttyS0: '/sbin/getty' Nov 1 13:26:52 shmotashNAS daemon.info wixEvent[3471]: System Startup - System startup. Nov 1 13:27:28 shmotashNAS daemon.warn wixEvent[3471]: Media Server - Media Server cannot find the path to one or more of the default folders: /Public/Shared Music, /Public/Shared Pictures or /Public/Shared Videos. Please verify that these folders have not been removed or that the names have not been changed. Nov 1 13:44:48 shmotashNAS auth.info sshd[5375]: Accepted password for root from 192.168.1.103 port 50217 ssh2 Nov 1 13:51:08 shmotashNAS auth.info sshd[5894]: Accepted password for root from 192.168.1.103 port 50380 ssh2

  Read the article

• DirectX works for 64-bit but not 32-bit

  - by dtbarne

  I'm trying to play a game (Civilization 5) which was previously working but no longer. I believe I've narrowed it down to a DirectX issue because I get an error running dxdiag.exe in 32 bit mode. My goal (at least I believe) is to get Direct3D Acceleration "Enabled" in dxdiag (as it is in 64 bit dxdiag). A very similar issue is here: http://answers.microsoft.com/en-us/windows/forum/windows_7-gaming/direct3d-acceleration-is-not-available-in-windows/4c345e6e-dc68-e011-8dfc-68b599b31bf5?page=1 The proposed answer, which looks very promising, doesn't seem to work for me. Like other users in that thread, HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Microsoft\Direct3D\Drivers does not have a SoftwareOnly key to change. I even tried manually adding it as a string and dword, to no avail. I have a NVIDIA GeForce GT 525M, and before you ask, yes I've tried updating (also uninstalling, reinstalling) my drivers. I've also tried doing the same with DirectX (and Civilization 5 for that matter). Been debugging for some 4+ hours now after a full day of work and I've run out of ideas. I'm hoping somebody knows the solution here! :) Here's what I see when I open dxdiag: DxDiag has detected that there mgiht have been a problem accessing Direct3D the last time this program was used. Would you like to bypass Direct3D this time? No - Crash Yes - Works, but in Display tab: DirectDraw Acceleration: Disabled Direct3D Acceleration: Not Available AGP Texture Acceleration: Not Available If I click "Run 64-bit DxDiag", all three are "Enabled". I should also note that I've tried the following steps as Microsoft suggests, but I'm not able to do so as the "Change Settings" button is disabled. Some programs run very slowly—or not at all—unless Microsoft DirectDraw or Direct3D hardware acceleration is turned on. To determine this, click the Display tab, and then under DirectX Features, check to see whether DirectDraw, Direct3D, and AGP Texture Acceleration appear as Enabled. If not, try turning on hardware acceleration. Click to open Screen Resolution. Click Advanced settings. Click the Troubleshoot tab, and then click Change settings. If you're prompted for an administrator password or confirmation, type the password or provide confirmation. Move the Hardware Acceleration slider to Full. Full dxdiag dump: ------------------ System Information ------------------ Time of this report: 11/8/2012, 23:13:24 Machine name: DTBARNE Operating System: Windows 7 Professional 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120830-0333) Language: English (Regional Setting: English) System Manufacturer: Dell Inc. System Model: Dell System XPS L502X BIOS: Default System BIOS Processor: Intel(R) Core(TM) i5-2450M CPU @ 2.50GHz (4 CPUs), ~2.5GHz Memory: 8192MB RAM Available OS Memory: 8086MB RAM Page File: 2466MB used, 13704MB available Windows Dir: C:\Windows DirectX Version: DirectX 11 DX Setup Parameters: Not found User DPI Setting: Using System DPI System DPI Setting: 96 DPI (100 percent) DWM DPI Scaling: Disabled DxDiag Version: 6.01.7601.17514 32bit Unicode DxDiag Previously: Crashed in Direct3D (stage 2). Re-running DxDiag with "dontskip" command line parameter or choosing not to bypass information gathering when prompted might result in DxDiag successfully obtaining this information ------------ DxDiag Notes ------------ Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Input Tab: No problems found. -------------------- DirectX Debug Levels -------------------- Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) --------------- Display Devices --------------- Card name: Intel(R) HD Graphics 3000 Manufacturer: Chip type: DAC type: Device Key: Enum\PCI\VEN_8086&DEV_0126&SUBSYS_04B61028&REV_09 Display Memory: Dedicated Memory: n/a Shared Memory: n/a Current Mode: 1920 x 1080 (32 bit) (60Hz) Monitor Name: Generic PnP Monitor Monitor Model: Monitor Id: Native Mode: Output Type: Driver Name: Driver File Version: () Driver Version: DDI Version: Driver Model: WDDM 1.1 Driver Attributes: Final Retail Driver Date/Size: , 0 bytes WHQL Logo'd: n/a WHQL Date Stamp: n/a Device Identifier: Vendor ID: Device ID: SubSys ID: Revision ID: Driver Strong Name: oem11.inf:IntelGfx.NTamd64.6.0:iSNBM0:8.15.10.2696:pci\ven_8086&dev_0126&subsys_04b61028 Rank Of Driver: 00E60001 Video Accel: Deinterlace Caps: n/a D3D9 Overlay: DXVA-HD: DDraw Status: Disabled D3D Status: Not Available AGP Status: Not Available ------------- Sound Devices ------------- Description: Speakers (High Definition Audio Device) Default Sound Playback: Yes Default Voice Playback: Yes Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0665&SUBSYS_102804B6&REV_1000 Manufacturer ID: 1 Product ID: 65535 Type: WDM Driver Name: HdAudio.sys Driver Version: 6.01.7601.17514 (English) Driver Attributes: Final Retail WHQL Logo'd: Yes Date and Size: 11/20/2010 22:23:47, 350208 bytes Other Files: Driver Provider: Microsoft HW Accel Level: Basic Cap Flags: 0xF1F Min/Max Sample Rate: 100, 200000 Static/Strm HW Mix Bufs: 1, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No Description: Digital Audio (S/PDIF) (High Definition Audio Device) Default Sound Playback: No Default Voice Playback: No Hardware ID: HDAUDIO\FUNC_01&VEN_10EC&DEV_0665&SUBSYS_102804B6&REV_1000 Manufacturer ID: 1 Product ID: 65535 Type: WDM Driver Name: HdAudio.sys Driver Version: 6.01.7601.17514 (English) Driver Attributes: Final Retail WHQL Logo'd: Yes Date and Size: 11/20/2010 22:23:47, 350208 bytes Other Files: Driver Provider: Microsoft HW Accel Level: Basic Cap Flags: 0xF1F Min/Max Sample Rate: 100, 200000 Static/Strm HW Mix Bufs: 1, 0 Static/Strm HW 3D Bufs: 0, 0 HW Memory: 0 Voice Management: No EAX(tm) 2.0 Listen/Src: No, No I3DL2(tm) Listen/Src: No, No Sensaura(tm) ZoomFX(tm): No --------------------- Sound Capture Devices --------------------- Description: Microphone (High Definition Audio Device) Default Sound Capture: Yes Default Voice Capture: Yes Driver Name: HdAudio.sys Driver Version: 6.01.7601.17514 (English) Driver Attributes: Final Retail Date and Size: 11/20/2010 22:23:47, 350208 bytes Cap Flags: 0x1 Format Flags: 0xFFFFF ------------------- DirectInput Devices ------------------- Device Name: Mouse Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Device Name: Keyboard Attached: 1 Controller ID: n/a Vendor/Product ID: n/a FF Driver: n/a Poll w/ Interrupt: No ----------- USB Devices ----------- + USB Root Hub | Vendor/Product ID: 0x8086, 0x1C26 | Matching Device ID: usb\root_hub20 | Service: usbhub | +-+ Generic USB Hub | | Vendor/Product ID: 0x8087, 0x0024 | | Location: Port_#0001.Hub_#0002 | | Matching Device ID: usb\class_09 | | Service: usbhub ---------------- Gameport Devices ---------------- ------------ PS/2 Devices ------------ + Standard PS/2 Keyboard | Matching Device ID: *pnp0303 | Service: i8042prt | + Terminal Server Keyboard Driver | Matching Device ID: root\rdp_kbd | Upper Filters: kbdclass | Service: TermDD | + Synaptics PS/2 Port TouchPad | Matching Device ID: *dll04b6 | Upper Filters: SynTP | Service: i8042prt | + Terminal Server Mouse Driver | Matching Device ID: root\rdp_mou | Upper Filters: mouclass | Service: TermDD ------------------------ Disk & DVD/CD-ROM Drives ------------------------ Drive: C: Free Space: 26.2 GB Total Space: 122.0 GB File System: NTFS Model: M4-CT128M4SSD2 ATA Device Drive: D: Model: Optiarc DVDRWBD BC-5540H ATA Device Driver: c:\windows\system32\drivers\cdrom.sys, 6.01.7601.17514 (English), , 0 bytes -------------- System Devices -------------- Name: High Definition Audio Controller Device ID: PCI\VEN_8086&DEV_1C20&SUBSYS_04B61028&REV_05\3&11583659&0&D8 Driver: n/a Name: PCI standard host CPU bridge Device ID: PCI\VEN_8086&DEV_0104&SUBSYS_04B61028&REV_09\3&11583659&0&00 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C1A&SUBSYS_04B61028&REV_B5\3&11583659&0&E5 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_0101&SUBSYS_20108086&REV_09\3&11583659&0&08 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C18&SUBSYS_04B61028&REV_B5\3&11583659&0&E4 Driver: n/a Name: Intel(R) Centrino(R) Advanced-N 6230 Device ID: PCI\VEN_8086&DEV_0091&SUBSYS_52218086&REV_34\4&2634DE8D&0&00E1 Driver: n/a Name: PCI standard ISA bridge Device ID: PCI\VEN_8086&DEV_1C4B&SUBSYS_04B61028&REV_05\3&11583659&0&F8 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C16&SUBSYS_04B61028&REV_B5\3&11583659&0&E3 Driver: n/a Name: Realtek PCIe GBE Family Controller Device ID: PCI\VEN_10EC&DEV_8168&SUBSYS_04B61028&REV_06\4&109EAB2F&0&00E5 Driver: n/a Name: Intel(R) Management Engine Interface Device ID: PCI\VEN_8086&DEV_1C3A&SUBSYS_04B61028&REV_04\3&11583659&0&B0 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C12&SUBSYS_04B61028&REV_B5\3&11583659&0&E1 Driver: n/a Name: NVIDIA GeForce GT 525M Device ID: PCI\VEN_10DE&DEV_0DF5&SUBSYS_04B61028&REV_A1\4&4DCA75F&0&0008 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_8086&DEV_1C2D&SUBSYS_04B61028&REV_05\3&11583659&0&D0 Driver: n/a Name: PCI standard PCI-to-PCI bridge Device ID: PCI\VEN_8086&DEV_1C10&SUBSYS_04B61028&REV_B5\3&11583659&0&E0 Driver: n/a Name: Standard Enhanced PCI to USB Host Controller Device ID: PCI\VEN_8086&DEV_1C26&SUBSYS_04B61028&REV_05\3&11583659&0&E8 Driver: n/a Name: Standard AHCI 1.0 Serial ATA Controller Device ID: PCI\VEN_8086&DEV_1C03&SUBSYS_04B61028&REV_05\3&11583659&0&FA Driver: n/a Name: SM Bus Controller Device ID: PCI\VEN_8086&DEV_1C22&SUBSYS_04B61028&REV_05\3&11583659&0&FB Driver: n/a Name: Intel(R) HD Graphics 3000 Device ID: PCI\VEN_8086&DEV_0126&SUBSYS_04B61028&REV_09\3&11583659&0&10 Driver: n/a Name: Renesas Electronics USB 3.0 Host Controller Device ID: PCI\VEN_1033&DEV_0194&SUBSYS_04B61028&REV_04\4&3494AC3A&0&00E3 Driver: n/a ------------------ DirectShow Filters ------------------ DirectShow Filters: WMAudio Decoder DMO,0x00800800,1,1,WMADMOD.DLL,6.01.7601.17514 WMAPro over S/PDIF DMO,0x00600800,1,1,WMADMOD.DLL,6.01.7601.17514 WMSpeech Decoder DMO,0x00600800,1,1,WMSPDMOD.DLL,6.01.7601.17514 MP3 Decoder DMO,0x00600800,1,1,mp3dmod.dll,6.01.7600.16385 Mpeg4s Decoder DMO,0x00800001,1,1,mp4sdecd.dll,6.01.7600.16385 WMV Screen decoder DMO,0x00600800,1,1,wmvsdecd.dll,6.01.7601.17514 WMVideo Decoder DMO,0x00800001,1,1,wmvdecod.dll,6.01.7601.17514 Mpeg43 Decoder DMO,0x00800001,1,1,mp43decd.dll,6.01.7600.16385 Mpeg4 Decoder DMO,0x00800001,1,1,mpg4decd.dll,6.01.7600.16385 DV Muxer,0x00400000,0,0,qdv.dll,6.06.7601.17514 Color Space Converter,0x00400001,1,1,quartz.dll,6.06.7601.17713 WM ASF Reader,0x00400000,0,0,qasf.dll,12.00.7601.17514 Screen Capture filter,0x00200000,0,1,wmpsrcwp.dll,12.00.7601.17514 AVI Splitter,0x00600000,1,1,quartz.dll,6.06.7601.17713 VGA 16 Color Ditherer,0x00400000,1,1,quartz.dll,6.06.7601.17713 SBE2MediaTypeProfile,0x00200000,0,0,sbe.dll,6.06.7601.17528 Microsoft DTV-DVD Video Decoder,0x005fffff,2,4,msmpeg2vdec.dll,6.01.7140.0000 AC3 Parser Filter,0x00600000,1,1,mpg2splt.ax,6.06.7601.17528 StreamBufferSink,0x00200000,0,0,sbe.dll,6.06.7601.17528 MJPEG Decompressor,0x00600000,1,1,quartz.dll,6.06.7601.17713 MPEG-I Stream Splitter,0x00600000,1,2,quartz.dll,6.06.7601.17713 SAMI (CC) Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7601.17514 MPEG-2 Splitter,0x005fffff,1,0,mpg2splt.ax,6.06.7601.17528 Closed Captions Analysis Filter,0x00200000,2,5,cca.dll,6.06.7601.17514 SBE2FileScan,0x00200000,0,0,sbe.dll,6.06.7601.17528 Microsoft MPEG-2 Video Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7601.17514 Internal Script Command Renderer,0x00800001,1,0,quartz.dll,6.06.7601.17713 MPEG Audio Decoder,0x03680001,1,1,quartz.dll,6.06.7601.17713 DV Splitter,0x00600000,1,2,qdv.dll,6.06.7601.17514 Video Mixing Renderer 9,0x00200000,1,0,quartz.dll,6.06.7601.17713 Microsoft MPEG-2 Encoder,0x00200000,2,1,msmpeg2enc.dll,6.01.7601.17514 ACM Wrapper,0x00600000,1,1,quartz.dll,6.06.7601.17713 Video Renderer,0x00800001,1,0,quartz.dll,6.06.7601.17713 MPEG-2 Video Stream Analyzer,0x00200000,0,0,sbe.dll,6.06.7601.17528 Line 21 Decoder,0x00600000,1,1,qdvd.dll,6.06.7601.17835 Video Port Manager,0x00600000,2,1,quartz.dll,6.06.7601.17713 Video Renderer,0x00400000,1,0,quartz.dll,6.06.7601.17713 VPS Decoder,0x00200000,0,0,WSTPager.ax,6.06.7601.17514 WM ASF Writer,0x00400000,0,0,qasf.dll,12.00.7601.17514 VBI Surface Allocator,0x00600000,1,1,vbisurf.ax,6.01.7601.17514 File writer,0x00200000,1,0,qcap.dll,6.06.7601.17514 iTV Data Sink,0x00600000,1,0,itvdata.dll,6.06.7601.17514 iTV Data Capture filter,0x00600000,1,1,itvdata.dll,6.06.7601.17514 DVD Navigator,0x00200000,0,3,qdvd.dll,6.06.7601.17835 Overlay Mixer2,0x00200000,1,1,qdvd.dll,6.06.7601.17835 AVI Draw,0x00600064,9,1,quartz.dll,6.06.7601.17713 RDP DShow Redirection Filter,0xffffffff,1,0,DShowRdpFilter.dll, Microsoft MPEG-2 Audio Encoder,0x00200000,1,1,msmpeg2enc.dll,6.01.7601.17514 WST Pager,0x00200000,1,1,WSTPager.ax,6.06.7601.17514 MPEG-2 Demultiplexer,0x00600000,1,1,mpg2splt.ax,6.06.7601.17528 DV Video Decoder,0x00800000,1,1,qdv.dll,6.06.7601.17514 SampleGrabber,0x00200000,1,1,qedit.dll,6.06.7601.17514 Null Renderer,0x00200000,1,0,qedit.dll,6.06.7601.17514 MPEG-2 Sections and Tables,0x005fffff,1,0,Mpeg2Data.ax,6.06.7601.17514 Microsoft AC3 Encoder,0x00200000,1,1,msac3enc.dll,6.01.7601.17514 StreamBufferSource,0x00200000,0,0,sbe.dll,6.06.7601.17528 Smart Tee,0x00200000,1,2,qcap.dll,6.06.7601.17514 Overlay Mixer,0x00200000,0,0,qdvd.dll,6.06.7601.17835 AVI Decompressor,0x00600000,1,1,quartz.dll,6.06.7601.17713 AVI/WAV File Source,0x00400000,0,2,quartz.dll,6.06.7601.17713 Wave Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 MIDI Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 Multi-file Parser,0x00400000,1,1,quartz.dll,6.06.7601.17713 File stream renderer,0x00400000,1,1,quartz.dll,6.06.7601.17713 Microsoft DTV-DVD Audio Decoder,0x005fffff,1,1,msmpeg2adec.dll,6.01.7140.0000 StreamBufferSink2,0x00200000,0,0,sbe.dll,6.06.7601.17528 AVI Mux,0x00200000,1,0,qcap.dll,6.06.7601.17514 Line 21 Decoder 2,0x00600002,1,1,quartz.dll,6.06.7601.17713 File Source (Async.),0x00400000,0,1,quartz.dll,6.06.7601.17713 File Source (URL),0x00400000,0,1,quartz.dll,6.06.7601.17713 Infinite Pin Tee Filter,0x00200000,1,1,qcap.dll,6.06.7601.17514 Enhanced Video Renderer,0x00200000,1,0,evr.dll,6.01.7601.17514 BDA MPEG2 Transport Information Filter,0x00200000,2,0,psisrndr.ax,6.06.7601.17669 MPEG Video Decoder,0x40000001,1,1,quartz.dll,6.06.7601.17713 WDM Streaming Tee/Splitter Devices: Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 Video Compressors: WMVideo8 Encoder DMO,0x00600800,1,1,wmvxencd.dll,6.01.7600.16385 WMVideo9 Encoder DMO,0x00600800,1,1,wmvencod.dll,6.01.7600.16385 MSScreen 9 encoder DMO,0x00600800,1,1,wmvsencd.dll,6.01.7600.16385 DV Video Encoder,0x00200000,0,0,qdv.dll,6.06.7601.17514 MJPEG Compressor,0x00200000,0,0,quartz.dll,6.06.7601.17713 Cinepak Codec by Radius,0x00200000,1,1,qcap.dll,6.06.7601.17514 Intel IYUV codec,0x00200000,1,1,qcap.dll,6.06.7601.17514 Intel IYUV codec,0x00200000,1,1,qcap.dll,6.06.7601.17514 Microsoft RLE,0x00200000,1,1,qcap.dll,6.06.7601.17514 Microsoft Video 1,0x00200000,1,1,qcap.dll,6.06.7601.17514 Audio Compressors: WM Speech Encoder DMO,0x00600800,1,1,WMSPDMOE.DLL,6.01.7600.16385 WMAudio Encoder DMO,0x00600800,1,1,WMADMOE.DLL,6.01.7600.16385 IMA ADPCM,0x00200000,1,1,quartz.dll,6.06.7601.17713 PCM,0x00200000,1,1,quartz.dll,6.06.7601.17713 Microsoft ADPCM,0x00200000,1,1,quartz.dll,6.06.7601.17713 GSM 6.10,0x00200000,1,1,quartz.dll,6.06.7601.17713 CCITT A-Law,0x00200000,1,1,quartz.dll,6.06.7601.17713 CCITT u-Law,0x00200000,1,1,quartz.dll,6.06.7601.17713 MPEG Layer-3,0x00200000,1,1,quartz.dll,6.06.7601.17713 Audio Capture Sources: Microphone (High Definition Aud,0x00200000,0,0,qcap.dll,6.06.7601.17514 PBDA CP Filters: PBDA DTFilter,0x00600000,1,1,CPFilters.dll,6.06.7601.17528 PBDA ETFilter,0x00200000,0,0,CPFilters.dll,6.06.7601.17528 PBDA PTFilter,0x00200000,0,0,CPFilters.dll,6.06.7601.17528 Midi Renderers: Default MidiOut Device,0x00800000,1,0,quartz.dll,6.06.7601.17713 Microsoft GS Wavetable Synth,0x00200000,1,0,quartz.dll,6.06.7601.17713 WDM Streaming Capture Devices: HD Audio Microphone 2,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 Integrated Webcam,0x00200000,1,2,ksproxy.ax,6.01.7601.17514 WDM Streaming Rendering Devices: HD Audio Headphone/Speakers,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 HD Audio SPDIF out,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 BDA Network Providers: Microsoft ATSC Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft DVBC Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft DVBS Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft DVBT Network Provider,0x00200000,0,1,MSDvbNP.ax,6.06.7601.17514 Microsoft Network Provider,0x00200000,0,1,MSNP.ax,6.06.7601.17514 Video Capture Sources: Integrated Webcam,0x00200000,1,2,ksproxy.ax,6.01.7601.17514 Multi-Instance Capable VBI Codecs: VBI Codec,0x00600000,1,4,VBICodec.ax,6.06.7601.17514 BDA Transport Information Renderers: BDA MPEG2 Transport Information Filter,0x00600000,2,0,psisrndr.ax,6.06.7601.17669 MPEG-2 Sections and Tables,0x00600000,1,0,Mpeg2Data.ax,6.06.7601.17514 BDA CP/CA Filters: Decrypt/Tag,0x00600000,1,1,EncDec.dll,6.06.7601.17708 Encrypt/Tag,0x00200000,0,0,EncDec.dll,6.06.7601.17708 PTFilter,0x00200000,0,0,EncDec.dll,6.06.7601.17708 XDS Codec,0x00200000,0,0,EncDec.dll,6.06.7601.17708 WDM Streaming Communication Transforms: Tee/Sink-to-Sink Converter,0x00200000,1,1,ksproxy.ax,6.01.7601.17514 Audio Renderers: Speakers (High Definition Audio,0x00200000,1,0,quartz.dll,6.06.7601.17713 Default DirectSound Device,0x00800000,1,0,quartz.dll,6.06.7601.17713 Default WaveOut Device,0x00200000,1,0,quartz.dll,6.06.7601.17713 Digital Audio (S/PDIF) (High De,0x00200000,1,0,quartz.dll,6.06.7601.17713 DirectSound: Digital Audio (S/PDIF) (High Definition Audio Device),0x00200000,1,0,quartz.dll,6.06.7601.17713 DirectSound: Speakers (High Definition Audio Device),0x00200000,1,0,quartz.dll,6.06.7601.17713 --------------- EVR Power Information --------------- Current Setting: {651288E5-A7ED-4076-A96B-6CC62D848FE1} (Balanced) Quality Flags: 2576 Enabled: Force throttling Allow half deinterlace Allow scaling Decode Power Usage: 100 Balanced Flags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 50 PowerFlags: 1424 Enabled: Force throttling Allow batching Force half deinterlace Force scaling Decode Power Usage: 0

  Read the article

• Normalisation and 'Anima notitia copia' (Soul of the Database)

  - by Phil Factor

  (A Guest Editorial for Simple-Talk) The other day, I was staring  at the sys.syslanguages  table in SQL Server with slightly-raised eyebrows . I’d just been reading Chris Date’s  interesting book ‘SQL and Relational Theory’. He’d made the point that you’re not necessarily doing relational database operations by using a SQL Database product.  The same general point was recently made by Dino Esposito about ASP.NET MVC.  The use of ASP.NET MVC doesn’t guarantee you a good application design: It merely makes it possible to test it. The way I’d describe the sentiment in both cases is ‘you can hit someone over the head with a frying-pan but you can’t call it cooking’. SQL enables you to create relational databases. However,  even if it smells bad, it is no crime to do hideously un-relational things with a SQL Database just so long as it’s necessary and you can tell the difference; not only that but also only if you’re aware of the risks and implications. Naturally, I’ve never knowingly created a database that Codd would have frowned at, but around the edges are interfaces and data feeds I’ve written  that have caused hissy fits amongst the Normalisation fundamentalists. Part of the problem for those who agonise about such things  is the misinterpretation of Atomicity.  An atomic value is one for which, in the strange virtual universe you are creating in your database, you don’t have any interest in any of its component parts.  If you aren’t interested in the electrons, neutrinos,  muons,  or  taus, then  an atom is ..er.. atomic. In the same way, if you are passed a JSON string or XML, and required to store it in a database, then all you need to do is to ask yourself, in your role as Anima notitia copia (Soul of the database) ‘have I any interest in the contents of this item of information?’.  If the answer is ‘No!’, or ‘nequequam! Then it is an atomic value, however complex it may be.  After all, you would never have the urge to store the pixels of images individually, under the misguided idea that these are the atomic values would you?  I would, of course,  ask the ‘Anima notitia copia’ rather than the application developers, since there may be more than one application, and the applications developers may be designing the application in the absence of full domain knowledge, (‘or by the seat of the pants’ as the technical term used to be). If, on the other hand, the answer is ‘sure, and we want to index the XML column’, then we may be in for some heavy XML-shredding sessions to get to store the ‘atomic’ values and ensure future harmony as the application develops. I went back to looking at the sys.syslanguages table. It has a months column with the months in a delimited list January,February,March,April,May,June,July,August,September,October,November,December This is an ordered list. Wicked? I seem to remember that this value, like shortmonths and days, is treated as a ‘thing’. It is merely passed off to an external  C++ routine in order to format a date in a particular language, and never accessed directly within the database. As far as the database is concerned, it is an atomic value.  There is more to normalisation than meets the eye.

  Read the article

• PC to USB transfer slow

  - by Vipin Ms

  I'm having trouble with USB transfer,not with external hard disk. Transfer starts with like, for the transfer of 700MB file it starts with 30mb/s and towards the end it stops at 0s and stays put for like 3-4 mins to transfer the last bit. I have tried different USB devices, but no luck. Is it a bug? Another important point is, in Kubuntu there is no such issue. So is it something related to Gnome? I'm using Ubuntu 11.10 64bit. Somebody please help, it's really annoying. Here are the details. PC all of my drives are in ext4. USB I tried ext3,ntfs and fat32. All having the same problem. Here are my USB controllers details: root@LAB:~# lspci|grep USB 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) Here is an example of one transfer. I connected one of my 4GB usb device. Nov 24 12:01:25 LAB kernel: [ 1175.082175] userif-2: sent link up event. Nov 24 12:01:25 LAB kernel: [ 1695.684158] usb 2-2: new high speed USB device number 3 using ehci_hcd Nov 24 12:01:25 LAB mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" Nov 24 12:01:26 LAB mtp-probe: bus: 2, device: 3 was not an MTP device Nov 24 12:01:26 LAB kernel: [ 1696.132680] usbcore: registered new interface driver uas Nov 24 12:01:26 LAB kernel: [ 1696.142528] Initializing USB Mass Storage driver... Nov 24 12:01:26 LAB kernel: [ 1696.142919] scsi4 : usb-storage 2-2:1.0 Nov 24 12:01:26 LAB kernel: [ 1696.143146] usbcore: registered new interface driver usb-storage Nov 24 12:01:26 LAB kernel: [ 1696.143150] USB Mass Storage support registered. Nov 24 12:01:27 LAB kernel: [ 1697.141657] scsi 4:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS Nov 24 12:01:27 LAB kernel: [ 1697.168827] sd 4:0:0:0: Attached scsi generic sg2 type 0 Nov 24 12:01:27 LAB kernel: [ 1697.169262] sd 4:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB) Nov 24 12:01:27 LAB kernel: [ 1697.169762] sd 4:0:0:0: [sdb] Write Protect is off Nov 24 12:01:27 LAB kernel: [ 1697.169767] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08 Nov 24 12:01:27 LAB kernel: [ 1697.171386] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.171391] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.173503] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.173510] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.175337] sdb: sdb1 After that I initiated one transfer. lsof -p 3575|tail -2 mv 3575 root 3r REG 8,8 1719599104 4325379 /media/Misc/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi mv 3575 root 4w REG 8,17 1046347776 15 /media/SREE/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi Here are the total time spent on that transfer. root@LAB:/media/SREE# time mv /media/Misc/The\ Tree\ of\ Life\ \(2011\)\ DVDRip\ XviD-MAXSPEED/ /media/SREE/ real 11m49.334s user 0m0.008s sys 0m5.260s root@LAB:/media/SREE# df -T|tail -2 /dev/sdb1 vfat 3918344 1679308 2239036 43% /media/SREE /dev/sda8 ext4 110110576 60096904 50013672 55% /media/Misc Do you think this is normal?? Approximately 12 minutes for 1.6Gb transfer? Thanks.

  Read the article

• 65536% Autogrowth!

  - by Tara Kizer

  Twice a year, we move our production systems to our disaster recovery site.  Last Saturday night was one of those days.  There are about 50 SQL Server databases to be moved to the DR site, which is done via database mirroring.  It takes only a few seconds to failover, but some databases have a bit more involved work such as setting up replication.  Everything went relatively smooth, but we encountered a weird bug on our most mission critical system.  After everything was successfully failed over to the DR site, it was noticed that mirroring was in a suspended state on one of the databases.  We thought we had run into a SQL Server 2005 bug that we had been encountering and were working with Microsoft on a fix.  Microsoft did fix it in both SQL Server 2005 service pack 3 cumulative update package 13 and service pack 4 cumulative update package 2, however SP3 CU13 and SP4 both recently failed on this system so we were not patched yet with the bug fix.  As the suspended state was causing us issues with replication, we dropped mirroring.  We then noticed we had 10MB of free disk space on the mount point where the principal’s data files are stored.  I knew something went amiss as this system should have at least 150GB free on that mount point.  I immediately checked the main database’s data file and was shocked to see an autgrowth size of 65536%.  The data file autogrew right before mirroring went into the suspended state. 65536%! I didn’t have a lot of time to research if this autgrowth problem was a known SQL Server bug, so I deferred that research to today.  A quick Google search yielded no results but emphasis on “quick”.  I checked our performance system, which was recently restored with a copy of the affected production database, and found the autogrowth setting to be 512MB.  So this autogrowth bug was encountered sometime in the last two weeks.  On February 26th, we had attempted to install SQL 2005 SP4 on production, however it had failed (PSS case open with Microsoft).  I suspected that the SP4 failure was somehow related to this autgrowth bug although that turned out not to be the case. I then tweeted (@TaraKizer) about this problem to see if the SQL Server community (#sqlhelp) had any insights.  It seems several people have either heard of this bug or encountered it.  Aaron Bertrand (blog|twitter) referred me to this Connect item. Our affected database originated on SQL Server 2000 and was upgraded to SQL Server 2005 in 2007.  Back on SQL Server 2000, we were using the default file growth setting which was a percentage.  Sometime after the 2005 upgrade is when we changed it to 512MB.  Our situation seemed to fit the bug Aaron referred to me, so now the question was whether Microsoft had fixed it yet. I received a reply to my tweet from Amit Banerjee (twitter) that it had been fixed in SP3 CU1 (KB958004).  My affected system is SP3 CU8, so I was initially confused why we had encountered the bug.  Because I don’t read things fully, I had missed that there are additional steps you have to follow after applying the bug fix.  Amit set me straight.  Although you can read this information in the KB article, I will also copy it here in case you are as lazy as me and miss the most important section of it (although if you are as lazy as me, you won’t have read this far down my blog post): This hotfix will prevent only future occurrences of this problem. For example, if you restore a database from SQL Server 2000 to a SQL Server 2005 instance that contains this hotfix, this problem will not occur. However, if you already have a database that is affected by this problem, you must follow these steps to resolve this problem manually: Apply this hotfix. Set the file growth settings for the affected files to percentage settings, and then set the settings back to megabyte settings. Take the database offline, and then bring it back online. Verify that the values of the is_percent_growth column are correct in the sys.database_files system table and in the sys.master_files system table.

  Read the article

• How to run RCU from the command line

  - by Kevin Smith

  When I was trying to figure out how to run RCU on 64-bit Linux I found this post. It shows how to run RCU from the command line. It didn't actually work for me, so you can see my post on how to run RCU on 64-bit Linux. But, seeing how to run RCU from the command got me started thinking about running RCU from the command line to create the schema for WebCenter Content. That post got me part of the way there since it shows how run RCU silently from the command line, but to do this you need to know the name of the RCU component for WebCenter Content. I poked around in the RCU files and found the component name for WCC is CONTENTSERVER11. There is a contentserver11 directory in rcuHome/rcu/integration and when you look at the contentserver11.xml file you will see <RepositoryConfig COMP_ID="CONTENTSERVER11"> With the component name for WCC in hand I was able to use this command line to run RCU and create the schema for WCC. .../rcuHome/bin/rcu -silent -createRepository -databaseType ORACLE -connectString localhost:1521:orcl1 -dbUser sys -dbRole sysdba -schemaPrefix TEST -component CONTENTSERVER11 -f <rcu_passwords.txt To make the silent part work and not have it prompt you for the passwords needed (sys password and password for each schema) you use the -f option and specify a file containing the passwords, one per line, in the order the components are listed on the -component argument. Here is the output from rcu when I ran the above command. Processing command line ....Repository Creation Utility - Checking PrerequisitesChecking Global PrerequisitesRepository Creation Utility - Checking PrerequisitesChecking Component PrerequisitesRepository Creation Utility - Creating TablespacesValidating and Creating TablespacesRepository Creation Utility - CreateRepository Create in progress.Percent Complete: 0...Percent Complete: 100Repository Creation Utility: Create - Completion SummaryDatabase details:Host Name              : localhostPort                   : 1521Service Name           : ORCL1Connected As           : sysPrefix for (prefixable) Schema Owners : TESTRCU Logfile            : /u01/app/oracle/logdir.2012-09-26_07-53/rcu.logComponent schemas created:Component                            Status  LogfileOracle Content Server 11g - Complete Success /u01/app/oracle/logdir.2012-09-26_07-53/contentserver11.logRepository Creation Utility - Create : Operation Completed This works fine if you want to use the default tablespace sizes and options, but there does not seem to be a way to specify the tablespace options on the command line. You can specify the name of the tablespace and temp tablespace, but they must already exist in the database before running RCU. I guess you can always create the tablespaces first using your desired sizes and options and then run RCU and specify the tablespaces you created. When looking up the command line options in the RCU doc I found it has the list of components for each product that it supports. See Appendix B in the RCU User's Guide.

  Read the article

• Using the Script Component as a Conditional Split

  This is a quick walk through on how you can use the Script Component to perform Conditional Split like behaviour, splitting your data across multiple outputs. We will use C# code to decide what does flows to which output, rather than the expression syntax of the Conditional Split transformation. Start by setting up the source. For my example the source is a list of SQL objects from sys.objects, just a quick way to get some data: SELECT type, name FROM sys.objects type name S syssoftobjrefs F FK_Message_Page U Conference IT queue_messages_23007163 Shown above is a small sample of the data you could expect to see. Once you have setup your source, add the Script Component, selecting Transformation when prompted for the type, and connect it up to the source. Now open the component, but don’t dive into the script just yet. First we need to select some columns. Select the Input Columns page and then select the columns we want to uses as part of our filter logic. You don’t need to choose columns that you may want later, this is just the columns used in the script itself. Next we need to add our outputs. Select the Inputs and Outputs page.You get one by default, but we need to add some more, it wouldn’t be much of a split otherwise. For this example we’ll add just one more. Click the Add Output button, and you’ll see a new output is added. Now we need to set some properties, so make sure our new Output 1 is selected. In the properties grid change the SynchronousInputID property to be our input Input 0, and  change the ExclusionGroup property to 1. Now select Ouput 0 and change the ExclusionGroup property to 2. This value itself isn’t important, provided each output has a different value other than zero. By setting this property on both outputs it allows us to split the data down one or the other, making each exclusive. If we left it to 0, that output would get all the rows. It can be a useful feature allowing you to copy selected rows to one output whilst retraining the full set of data in the other. Now we can go back to the Script page and start writing some code. For the example we will do a very simple test, if the value of the type column is U, for user table, then it goes down the first output, otherwise it ends up in the other. This mimics the exclusive behaviour of the conditional split transformation. public override void Input0_ProcessInputRow(Input0Buffer Row) { // Filter all user tables to the first output, // the remaining objects down the other if (Row.type.Trim() == "U") { Row.DirectRowToOutput0(); } else { Row.DirectRowToOutput1(); } } The code itself is very simple, a basic if clause that determines which of the DirectRowToOutput methods we call, there is one for each output. Of course you could write a lot more code to implement some very complex logic, but the final direction is still just a method call. If we now close the script component, we can hook up the outputs and test the package. Your numbers will vary depending on the sample database but as you can see we have clearly split out input data into two outputs. As a final tip, when adding the outputs I would normally rename them, changing the Name in the Properties grid. This means the generated methods follow the pattern as do the path label shown on the design surface, making everything that much easier to recognise.

  Read the article

• Indexed view deadlocking

  - by Dave Ballantyne

  Deadlocks can be a really tricky thing to track down the root cause of.  There are lots of articles on the subject of tracking down deadlocks, but seldom do I find that in a production system that the cause is as straightforward.  That being said,  deadlocks are always caused by process A needs a resource that process B has locked and process B has a resource that process A needs.  There may be a longer chain of processes involved, but that is the basic premise. Here is one such (much simplified) scenario that was at first non-obvious to its cause: The system has two tables,  Products and Stock.  The Products table holds the description and prices of a product whilst Stock records the current stock level. USE tempdb GO CREATE TABLE Product ( ProductID INTEGER IDENTITY PRIMARY KEY, ProductName VARCHAR(255) NOT NULL, Price MONEY NOT NULL ) GO CREATE TABLE Stock ( ProductId INTEGER PRIMARY KEY, StockLevel INTEGER NOT NULL ) GO INSERT INTO Product SELECT TOP(1000) CAST(NEWID() AS VARCHAR(255)), ABS(CAST(CAST(NEWID() AS VARBINARY(255)) AS INTEGER))%100 FROM sys.columns a CROSS JOIN sys.columns b GO INSERT INTO Stock SELECT ProductID,ABS(CAST(CAST(NEWID() AS VARBINARY(255)) AS INTEGER))%100 FROM Product There is a single stored procedure of GetStock: Create Procedure GetStock as SELECT Product.ProductID,Product.ProductName FROM dbo.Product join dbo.Stock on Stock.ProductId = Product.ProductID where Stock.StockLevel <> 0 Analysis of the system showed that this procedure was causing a performance overhead and as reads of this data was many times more than writes,  an indexed view was created to lower the overhead. CREATE VIEW vwActiveStock With schemabinding AS SELECT Product.ProductID,Product.ProductName FROM dbo.Product join dbo.Stock on Stock.ProductId = Product.ProductID where Stock.StockLevel <> 0 go CREATE UNIQUE CLUSTERED INDEX PKvwActiveStock on vwActiveStock(ProductID) This worked perfectly, performance was improved, the team name was cheered to the rafters and beers all round.  Then, after a while, something else happened… The system updating the data changed,  The update pattern of both the Stock update and the Product update used to be: BEGIN TRAN UPDATE... COMMIT BEGIN TRAN UPDATE... COMMIT BEGIN TRAN UPDATE... COMMIT It changed to: BEGIN TRAN UPDATE... UPDATE... UPDATE... COMMIT Nothing that would raise an eyebrow in even the closest of code reviews.  But after this change we saw deadlocks occuring. You can reproduce this by opening two sessions. In session 1 begin transaction Update Product set ProductName ='Test' where ProductID = 998 Then in session 2 begin transaction Update Stock set Stocklevel = 5 where ProductID = 999 Update Stock set Stocklevel = 5 where ProductID = 998 Hop back to session 1 and.. Update Product set ProductName ='Test' where ProductID = 999 Looking at the deadlock graphs we could see the contention was between two processes, one updating stock and the other updating product, but we knew that all the processes do to the tables is update them.  Period.  There are separate processes that handle the update of stock and product and never the twain shall meet, no reason why one should be requiring data from the other.  Then it struck us,  AH the indexed view. Naturally, when you make an update to any table involved in a indexed view, the view has to be updated.  When this happens, the data in all the tables have to be read, so that explains our deadlocks.  The data from stock is read when you update product and vice-versa. The fix, once you understand the problem fully, is pretty simple, the apps did not guarantee the order in which data was updated.  Luckily it was a relatively simple fix to order the updates and deadlocks went away.  Note, that there is still a *slight* risk of a deadlock occurring, if both a stock update and product update occur at *exactly* the same time.

  Read the article

• SQL Server IO handling mechanism can be severely affected by high CPU usage

  - by sqlworkshops

  Are you using SSD or SAN / NAS based storage solution and sporadically observe SQL Server experiencing high IO wait times or from time to time your DAS / HDD becomes very slow according to SQL Server statistics? Read on… I need your help to up vote my connect item – https://connect.microsoft.com/SQLServer/feedback/details/744650/sql-server-io-handling-mechanism-can-be-severely-affected-by-high-cpu-usage. Instead of taking few seconds, queries could take minutes/hours to complete when CPU is busy.In SQL Server when a query / request needs to read data that is not in data cache or when the request has to write to disk, like transaction log records, the request / task will queue up the IO operation and wait for it to complete (task in suspended state, this wait time is the resource wait time). When the IO operation is complete, the task will be queued to run on the CPU. If the CPU is busy executing other tasks, this task will wait (task in runnable state) until other tasks in the queue either complete or get suspended due to waits or exhaust their quantum of 4ms (this is the signal wait time, which along with resource wait time will increase the overall wait time). When the CPU becomes free, the task will finally be run on the CPU (task in running state).The signal wait time can be up to 4ms per runnable task, this is by design. So if a CPU has 5 runnable tasks in the queue, then this query after the resource becomes available might wait up to a maximum of 5 X 4ms = 20ms in the runnable state (normally less as other tasks might not use the full quantum).In case the CPU usage is high, let’s say many CPU intensive queries are running on the instance, there is a possibility that the IO operations that are completed at the Hardware and Operating System level are not yet processed by SQL Server, keeping the task in the resource wait state for longer than necessary. In case of an SSD, the IO operation might even complete in less than a millisecond, but it might take SQL Server 100s of milliseconds, for instance, to process the completed IO operation. For example, let’s say you have a user inserting 500 rows in individual transactions. When the transaction log is on an SSD or battery backed up controller that has write cache enabled, all of these inserts will complete in 100 to 200ms. With a CPU intensive parallel query executing across all CPU cores, the same inserts might take minutes to complete. WRITELOG wait time will be very high in this case (both under sys.dm_io_virtual_file_stats and sys.dm_os_wait_stats). In addition you will notice a large number of WAITELOG waits since log records are written by LOG WRITER and hence very high signal_wait_time_ms leading to more query delays. However, Performance Monitor Counter, PhysicalDisk, Avg. Disk sec/Write will report very low latency times.Such delayed IO handling also occurs to read operations with artificially very high PAGEIOLATCH_SH wait time (with number of PAGEIOLATCH_SH waits remaining the same). This problem will manifest more and more as customers start using SSD based storage for SQL Server, since they drive the CPU usage to the limits with faster IOs. We have a few workarounds for specific scenarios, but we think Microsoft should resolve this issue at the product level. We have a connect item open – https://connect.microsoft.com/SQLServer/feedback/details/744650/sql-server-io-handling-mechanism-can-be-severely-affected-by-high-cpu-usage - (with example scripts) to reproduce this behavior, please up vote the item so the issue will be addressed by the SQL Server product team soon.Thanks for your help and best regards,Ramesh MeyyappanHome: www.sqlworkshops.comLinkedIn: http://at.linkedin.com/in/rmeyyappan

  Read the article

• Ubuntu 12.04 LXC nat prerouting not working

  - by petermolnar

  I have a running Debian Wheezy setup I copied exactly to an Ubuntu 12.04 ( elementary OS, used as desktop as well ) While the Debian setup runs flawlessly, the Ubuntu version dies on the prerouting to containers ( or so it seems ) In short: lxc works containers work and run connecting to container from host OK ( including mixed ports & services ) connecting to outside world from container is fine What does not work is connecting from another box to the host on a port that should be NATed to a container. The setups: /etc/rc.local CMD_BRCTL=/sbin/brctl CMD_IFCONFIG=/sbin/ifconfig CMD_IPTABLES=/sbin/iptables CMD_ROUTE=/sbin/route NETWORK_BRIDGE_DEVICE_NAT=lxc-bridge HOST_NETDEVICE=eth0 PRIVATE_GW_NAT=192.168.42.1 PRIVATE_NETMASK=255.255.255.0 PUBLIC_IP=192.168.13.100 ${CMD_BRCTL} addbr ${NETWORK_BRIDGE_DEVICE_NAT} ${CMD_BRCTL} setfd ${NETWORK_BRIDGE_DEVICE_NAT} 0 ${CMD_IFCONFIG} ${NETWORK_BRIDGE_DEVICE_NAT} ${PRIVATE_GW_NAT} netmask ${PRIVATE_NETMASK} promisc up Therefore lxc network is 192.168.42.0/24 and the host eth0 ip is 192.168.13.100; setup via network manager as static address. iptables: *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT *filter :FORWARD ACCEPT [0:0] :INPUT DROP [0:0] :OUTPUT ACCEPT [0:0] # Accept traffic from internal interfaces -A INPUT -i lo -j ACCEPT # accept traffic from lxc network -A INPUT -d 192.168.42.1 -s 192.168.42.0/24 -j ACCEPT # Accept internal traffic Make sure NEW incoming tcp connections are SYN # packets; otherwise we need to drop them: -A INPUT -p tcp ! --syn -m state --state NEW -j DROP # Packets with incoming fragments drop them. This attack result into Linux server panic such data loss. -A INPUT -f -j DROP # Incoming malformed XMAS packets drop them: -A INPUT -p tcp --tcp-flags ALL ALL -j DROP # Incoming malformed NULL packets: -A INPUT -p tcp --tcp-flags ALL NONE -j DROP # Accept traffic with the ACK flag set -A INPUT -p tcp -m tcp --tcp-flags ACK ACK -j ACCEPT # Allow incoming data that is part of a connection we established -A INPUT -m state --state ESTABLISHED -j ACCEPT # Allow data that is related to existing connections -A INPUT -m state --state RELATED -j ACCEPT # Accept responses to DNS queries -A INPUT -p udp -m udp --dport 1024:65535 --sport 53 -j ACCEPT # Accept responses to our pings -A INPUT -p icmp -m icmp --icmp-type echo-reply -j ACCEPT # Accept notifications of unreachable hosts -A INPUT -p icmp -m icmp --icmp-type destination-unreachable -j ACCEPT # Accept notifications to reduce sending speed -A INPUT -p icmp -m icmp --icmp-type source-quench -j ACCEPT # Accept notifications of lost packets -A INPUT -p icmp -m icmp --icmp-type time-exceeded -j ACCEPT # Accept notifications of protocol problems -A INPUT -p icmp -m icmp --icmp-type parameter-problem -j ACCEPT # Respond to pings, but limit -A INPUT -m icmp -p icmp --icmp-type echo-request -m state --state NEW -m limit --limit 6/s -j ACCEPT # Allow connections to SSH server -A INPUT -p tcp -m tcp --dport 22 -m state --state NEW -m limit --limit 12/s -j ACCEPT COMMIT *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A PREROUTING -d 192.168.13.100 -p tcp -m tcp --dport 2221 -m state --state NEW -m limit --limit 12/s -j DNAT --to-destination 192.168.42.11:22 -A PREROUTING -d 192.168.13.100 -p tcp -m tcp --dport 80 -m state --state NEW -m limit --limit 512/s -j DNAT --to-destination 192.168.42.11:80 -A PREROUTING -d 192.168.13.100 -p tcp -m tcp --dport 443 -m state --state NEW -m limit --limit 512/s -j DNAT --to-destination 192.168.42.11:443 -A POSTROUTING -d 192.168.42.0/24 -o eth0 -j SNAT --to-source 192.168.13.100 -A POSTROUTING -o eth0 -j MASQUERADE COMMIT sysctl: net.ipv4.conf.all.forwarding = 1 net.ipv4.conf.all.mc_forwarding = 0 net.ipv4.conf.default.forwarding = 1 net.ipv4.conf.default.mc_forwarding = 0 net.ipv4.ip_forward = 1 I've set up full iptables log on the container; none of the packets addressed to 192.168.13.100, port 80 is reaching the container. I've even tried different kernels ( server kernel, raring lts kernel, etc ), modprobe everything iptables & nat related, nothing. Any ideas?

  Read the article

• Problem in udp socket programing in c

  - by Md. Talha

  I complile the following C code of UDP client after I run './udpclient localhost 9191' in terminal.I put "Enter Text= " as Hello, but it is showing error in sendto as below: Enter text: hello hello : error in sendto()guest-1SDRJ2@md-K42F:~/Desktop$ " Note: I open 1st the server port as below in other terminal ./server 9191. I beleive there is no error in server code. The udp client is not passing message to server. If I don't use thread , the message is passing .But I have to do it by thread. UDP client Code: /* simple UDP echo client */ #include <sys/types.h> #include <sys/socket.h> #include <netinet/in.h> #include <arpa/inet.h> #include <netdb.h> #include <stdio.h> #include <pthread.h> #define STRLEN 1024 static void *readdata(void *); static void *writedata(void *); int sockfd, n, slen; struct sockaddr_in servaddr; char sendline[STRLEN], recvline[STRLEN]; int main(int argc, char *argv[]) { pthread_t readid,writeid; struct sockaddr_in servaddr; struct hostent *h; if(argc != 3) { printf("Usage: %s <proxy server ip> <port>\n", argv[0]); exit(0); } /* create hostent structure from user entered host name*/ if ( (h = gethostbyname(argv[1])) == NULL) { printf("\n%s: error in gethostbyname()", argv[0]); exit(0); } /* create server address structure */ bzero(&servaddr, sizeof(servaddr)); /* initialize it */ servaddr.sin_family = AF_INET; memcpy((char *) &servaddr.sin_addr.s_addr, h->h_addr_list[0], h->h_length); servaddr.sin_port = htons(atoi(argv[2])); /* get the port number from argv[2]*/ /* create a UDP socket: SOCK_DGRAM */ if ( (sockfd = socket(AF_INET,SOCK_DGRAM, 0)) < 0) { printf("\n%s: error in socket()", argv[0]); exit(0); } pthread_create(&readid,NULL,&readdata,NULL); pthread_create(&writeid,NULL,&writedata,NULL); while(1) { }; close(sockfd); } static void * writedata(void *arg) { /* get user input */ printf("\nEnter text: "); do { if (fgets(sendline, STRLEN, stdin) == NULL) { printf("\n%s: error in fgets()"); exit(0); } /* send a text */ if (sendto(sockfd, sendline, sizeof(sendline), 0, (struct sockaddr *) &servaddr, sizeof(servaddr)) < 0) { printf("\n%s: error in sendto()"); exit(0); } }while(1); } static void * readdata(void *arg) { /* wait for echo */ slen = sizeof(servaddr); if ( (n = recvfrom(sockfd, recvline, STRLEN, 0, (struct sockaddr *) &servaddr, &slen)) < 0) { printf("\n%s: error in recvfrom()"); exit(0); } /* null terminate the string */ recvline[n] = 0; fputs(recvline, stdout); }

  Read the article

• Ubuntu 12.10 no network and no graphics

  - by khasiKoMasu

  I recently upgraded Ubuntu 12.04 to 12.10 only to find out that it won't connect to any network, neither wired nor wireless and the graphics is messed up too as in a low screen resolution. For 12.04, my system was running perfectly. I don't know why upgrade messed it up so bad. Reinstalling the OS is an issue because I have set up a lot of development environments that I cannot afford to set it up again. Some of the outputs: lspci -nn | grep 0200 02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) nm-tool NetworkManager Tool State: disconnected cat /etc/network/interfaces auto lo iface lo inet loopback sudo cat /var/log/syslog | grep etwork | tail -n20 Nov 2 13:50:22 Cobalt NetworkManager[978]: SCPlugin-Ifupdown: (-1240454760) ... get_connections (managed=false): return empty list. Nov 2 13:50:22 Cobalt NetworkManager[978]: Ifupdown: get unmanaged devices count: 0 Nov 2 13:50:22 Cobalt bluetoothd[1016]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> modem-manager is now available Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> monitoring kernel firmware directory '/lib/firmware'. Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiFi enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WWAN enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> WiMAX enabled by radio killswitch; enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <info> Networking is enabled by state file Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> /sys/devices/virtual/net/lo: couldn't determine device driver; ignoring... Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt kernel: [ 28.688167] type=1400 audit(1351882222.452:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1046 comm="apparmor_parser" Nov 2 13:50:22 Cobalt bluetoothd[1062]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1118]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) Nov 2 13:50:22 Cobalt bluetoothd[1237]: Failed to init network plugin Nov 2 13:50:22 Cobalt NetworkManager[978]: <warn> bluez error getting default adapter: Message did not receive a reply (timeout by message bus) ps aux | grep -i network root 978 0.0 0.1 23732 4808 ? Ssl 13:50 0:00 NetworkManager sudo modprobe -r forcedeth FATAL: Module forcedeth not found

  Read the article

• Detect user logout / shutdown in Python / GTK under Linux

  - by Ivo Wetzel

  OK this is presumably a hard one, I've got an pyGTK application that has random crashes due to X Window errors that I can't catch/control. So I created a wrapper that restarts the app as soon as it detects a crash, now comes the problem, when the user logs out or shuts down the system, the app exits with status 1. But on some X errors it does so too. So I tried literally anything to catch the shutdown/logout, with no success, here's what I've tried: import pygtk import gtk import sys class Test(gtk.Window): def delete_event(self, widget, event, data=None): open("delete_event", "wb") def destroy_event(self, widget, data=None): open("destroy_event", "wb") def destroy_event2(self, widget, event, data=None): open("destroy_event2", "wb") def __init__(self): gtk.Window.__init__(self, gtk.WINDOW_TOPLEVEL) self.show() self.connect("delete_event", self.delete_event) self.connect("destroy", self.destroy_event) self.connect("destroy-event", self.destroy_event2) def foo(): open("add_event", "wb") def ex(): open("sys_event", "wb") from signal import * def clean(sig): f = open("sig_event", "wb") f.write(str(sig)) f.close() exit(0) for sig in (SIGABRT, SIGILL, SIGINT, SIGSEGV, SIGTERM): signal(sig, lambda *args: clean(sig)) def at(): open("at_event", "wb") import atexit atexit.register(at) f = Test() sys.exitfunc = ex gtk.quit_add(gtk.main_level(), foo) gtk.main() open("exit_event", "wb") Not one of these succeeds, is there any low level way to detect the system shutdown? Google didn't find anything related to that. I guess there must be a way, am I right? :/

  Read the article

< Previous Page | 113 114 115 116 117 118 119 120 121 122 123 124  | Next Page >