Search Results

Search found 3564 results on 143 pages for 'weblogic channel'.

Page 119/143 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >

• VMWare Raw Device Mapping Not Working

  - by George H. Lenzer

  While I'm waiting for VMWare support to get back to me, I thought I'd ask here. I have a 400 gig LUN presented from a fiber channel SAN to my VMWare host. It's legacy from another virtualization platform and I need to keep it as is to avoid a long period of downtime. I formatted my VMFS3 datastore with 4 meg blocks to allow up to 1 TB disks. Then I tried adding my 400 gig disk as a raw device in physical compatibility mode. I get the error: "File is larger than the maximum size supported by datastore 'Base Test'. [Base Test]VMTEST01/VMTEST01_2.vmdk Originally I had the VMFS datastore formatted with 1 meg blocks which was the cause of this problem since the largest disk allowed would be 256 gigs. But I deleted the data store and then reformatted with 4 megs blocks. I've also tried using virtual compatibility mode for the raw device but it still fails. Does anyone have any suggestions? I've been waiting for a little over a week for VMWare, but that's fine because I'm not yet a paying customer. I'm still in the eval phase.

  Read the article

• Troubleshooting wireless client-bridged networks between two DD-WRT routers?

  - by KronoS

  I recently purchased a Buffalo N600 wireless router which came with DD-WRT pre-installed. I want to take my old wireless router a Linksys WRT54GL, also with DD-WRT pre-installed, and use it as a wireless bridge for my HTPC and Blu-Ray Player in the other room. I other words, I'm trying to connect to WIRED networks via the wireless on the routers. I followed eactly the instruction from DD-WRT's manual for 'Client Bridged' however I'm still not able to connect to two routers correctly, when the encryption is enabled (WPA2-Personal Mixed) however I am able to connect the two routers when there is NO encryption. I've checked, double checked, and triple checked that EVERYTHING is the same on BOTH routers: Routers 1 & 2 Encryption: WPA2-Personal Mixed Wireless Mode: G-Only Wireless Channel: 6 Subnet Mask: 255.255.255.0 Subnet: 192.168.1.0/254 SSID: Krono$ Primary Router #1 (Buffalo N600) IP Address: 192.168.1.1 Firewall: Enables w/ defaults DCHP: Enabled as DHCP Server Secondary Router #2 (Linksys WRT54GL) IP Address: 192.168.1.2 Firewall: Disabled as per DD-WRT instructions I'm looking for any configurations that I may have missed, or settings that may need to happen in order for this work.

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• QCon: A practitioner-driven conference for Developers

  - by Ruma Sanyal

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} QCon [http://www.qconsf.com] started yesterday with the 3-day conference from Monday thru Wednesday, followed by 2 days of tutorials on Thursday and Friday. The conference features over 100 speakers in 6 concurrent tracks daily covering the most timely and innovative topics driving the evolution of enterprise software development today. Oracle and its Cloud Application Foundation products are well represented at this event. Yesterday, Joe Huang, responsible for outbound product management of Oracle's Mobile Application Development Framework (ADF Mobile), discussed hybrid mobile development with Java & HTML5 for iOS and Android. If you missed Joe’s session you can download the presentation from here. Michael Kovacs will be talking tomorrow about how to keep your application data highly available. Michael works with Oracle customers in a pre-sales role to help them understand when and how to use Oracle's technology to solve their business problems. His focus is on Java and technologies like WebLogic and Coherence. His session details can be found here. Lastly, we believe in having fun. So don’t miss the Oracle hospitality reception today at the Hyatt Atrium. See you there!   /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif"; mso-fareast-font-family:"Times New Roman";}

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• Multi-WAN bonding across different media

  - by Tom O'Connor

  I've recently been thinking again about a product that Viprinet provide, basically they've got a pair of routers, one that lives in a datacentre, Their VPN Multichannel Hub and the on-site hardware, their VPN multichannel routers They've also got a bunch of interface cards (like HWICs) for 3G, UMTS, Ethernet, ADSL and ISDN adapters. Their main spiel seems to be bonding across different media. It's something that I'd really like to use for a couple of projects, but their pricing is really quite extreme, the hub is about 1-2k, the routers are 2-6k, and the interface modules are 200-600 each. So, what I'd like to know is, is it possible with a couple of stock Cisco routers, 28xx or 18xx series, to do something similar, and basically connect a bunch of different WAN ports, but have it all presented neatly as one channel back to the internet, with seamless (or nearly) failover if one of the WAN interfaces should fail. Basically, If i got 3x 3G to ethernet modems, and each on a different network, I'd like to be able to loadbalance/bond across all of them, without having to pay Viprinet for the privilege. Does anyone know how I'd go about configuring something for myself, based around standard protocols (or vendor specific ones), but without actually having to buy the Viprinet hardware?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• Am I getting the right memory for my motherboard?

  - by Daniel Carvalho

  Hi technophiles; I have a Gigabyte GA-EP45-DS motherboard. Also, the memory that came with my computer was two Transcend aXe RAM 1066MHZ 1GB modules. The thing is, I noticed that my motherboard has "DDR2 1200" written on it. This concerns me, have I bought slower memory than my computer is supposed to have ideally? Now, I'm not super concerned at a granular level about the best optimal RAM with the best CAS latency etc... but I do hope at least that I've got the right speed. Now, as far as I know, there is no such thing as ram at 1200MHZ? Am I right? You see, because I'm thinking of getting more RAM now, before I can't find the same type or speed any-more and just want to make sure it's the right thing. Furthermore, if the memory is slower than what I should be getting for my motherboard, what RAM should I be getting, and will that new RAM play nice with my old RAM? If I get new RAM at a different speed, would it be better / more beneficial performance-wise to omit the old RAM because of how the whole DUAL channel RAM thing works? I'm not too clued up on this area. Thanks chiefs.

  Read the article

• Too many concurrent connections Exchange 2010. What else is there to check?

  - by hydroparadise

  I thought that I had this under control before. But for some reason during our last email marketing promo, I start receiving from our mass email client (built in house).. The message could not be sent to the SMTP server. The transport error code is 0x800ccc67. The server repsonse was 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel again. There's several places I've checked to make sure that wouldn't be an issue. First I checked that receive connector was set to receive an adequate number of connections on our relay connector (1000 connections). Then, I would later find out about Throttling Policies. I created one and set all the properties I knew to set in terms of the policy following properties to 1000; EWSMaxConcurrency, OWAMaxConcurrency, CPAMaxConcurrency, and CPAMaxConcurrency. Still, the email client starts receiving the error shortly after 100 has been sent and takes about 15-30 seconds. The process is then repeatable, but still the error gets received at the same spot everytime. Is there a rate setting that I am missing? Was there a windows update that I missed looking at? Should the software have it's own throttling feature?

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• This .mpg video clip doesn't play well

  - by Roey

  I've installed K-lite mega codec pack v6.9.0 with playback essentials without player. My default and only media player is windows media player. here are the clip's media info: General Complete name : D:\Users\Roey\Downloads\B384MV.mpg Format : MPEG-PS File size : 273 MiB Duration : 4mn 59s Overall bit rate : 7 643 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@High Format settings, BVOP : No Format settings, Matrix : Default Format settings, GOP : M=1, N=15 Duration : 4mn 57s Bit rate mode : Variable Bit rate : 7 363 Kbps Nominal bit rate : 9 000 Kbps Width : 1 920 pixels Height : 1 080 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Compression mode : Lossy Bits/(Pixel*Frame) : 0.142 Stream size : 261 MiB (96%) Audio ID : 192 (0xC0) Format : MPEG Audio Format version : Version 1 Format profile : Layer 3 Mode : Joint stereo Duration : 4mn 59s Bit rate mode : Constant Bit rate : 128 Kbps Channel(s) : 2 channels Sampling rate : 44.1 KHz Compression mode : Lossy Stream size : 4.56 MiB (2%) Menu When I play it there is no sound (just a little "kahhhh" noise every 10-20 seconds) and the frames are moving very slow - it "jumps" frames. A blue tray icon [FFa] "ffdshow audio decoder" pops with the following details: Input:MP3, stereo, 44100 Hz (libavocodec) Output:PCM, stereo, 44100 Hz, 16-bit integer Any help will be much appreciated. Thanks

  Read the article

• October 2013 Fusion Middleware (FMW) Proactive Patches released

  - by PCat

  We are glad to announce that the following Fusion Middleware (FMW) Proactive  patches were released on October 15, 2013.Bundle PatchesBundle patches are collections of controlled, well tested critical bug fixes for a specific product  which may include security contents and occasionally minor enhancements. These are cumulative in nature meaning the latest bundle patch in a particular series includes the contents of the previous bundle patches released.  A suite bundle patch is an aggregation of multiple product  bundle patches that are part of a product suite. Oracle Identity Management Suite Bundle Patch 11.1.1.5.5 consisting of Oracle Identity Manager (OIM) 11.1.1.5.9 bundle patch Oracle Access Manager (OAM) 11.1.1.5.6 bundle patch. Oracle Adaptive Access Manager (OAAM) 11.1.1.5.2 bundle patch. Oracle Entitlement Server (OES) 11.1.1.5.4 bundle patch. Oracle Identity Management Suite Bundle Patch 11.1.2.0.4 consisting of Oracle Access Manager (OAM) 11.1.2.0.4 bundle patch. Oracle Adaptive Access Manager (OAAM) 11.1.2.0.2 bundle patch. Oracle Entitlement Server (OES) 11.1.2.0.2 bundle patch. Oracle Identity Analytics (OIA ) 11.1.1.5.6  bundle patch. Oracle GlassFish Server (OGFS) 2.1.1.22, 3.0.1.8 and 3.1.2.7 bundle patches. Oracle iPlanet Web Server (OiWS) 7.0.18 bundle patch Oracle SOA Suite (SOA) 11.1.1.7.1 bundle patch Oracle WebCenter Portal (WCP) 11.1.1.8.1 bundle patch Sun Role Manager (SRM) 4.1.7 and 5.0.3.2 bundle patches. Patch Set Updates (PSU)Patch Set Updates (PSU)  are collections of well controlled, well tested critical bug fixes for a specific product  that have been proven in customer environments. PSUs  may include security contents but no  enhancements are included. These are cumulative in nature meaning the latest PSU  in a particular series includes the contents of the previous PSUs  released. Oracle Exalogic 2.0.3.0.4 Physical Linux x86-64 and 2.0.4.0.4 Physical Solaris x86-64 PSUs. Oracle WebLogic Server 10.3.6.0.6 and 12.1.1.0.6 PSUs. Critical Patch Update (CPU)The Critical Patch Update program is Oracle's quarterly release of security fixes.The following additional patches were released as part of Oracle's Critical Patch Update program: Oracle JDeveloper 11.1.2.3.0, 11.1.2.4.0 and 12.1.2.0.0 Oracle Outside In Technology 8.4.0 and  8.4.1 Oracle Portal 11.1.1.6.0 Oracle Security Service  11.1.1.6.0, 11.1.1.7.0 and 12.1.2.0.0 Oracle WebCache 11.1.1.6.0 and 11.1.1.7.0 Oracle WebCenter Content 10.1.3.5.1, 11.1.1.6.0, 11.1.1.7.0 and 11.1.1.8.0 Oracle WebServices 10.1.3.5.0 and 11.1.1.6.0 For more information: Master Notes on Fusion Middleware Proactive Patching PSU and CPU October 2013  Availability Document Critical Patch Update Advisory -  October 2013

  Read the article

• nginx: dump HTTP requests for debugging

  - by Alexander Gladysh

  Ubuntu 10.04.2 nginx 0.7.65 I see some weird HTTP requests coming to my nginx server. To better understand what is going on, I want to dump whole HTTP request data for such queries. (I.e. dump all request headers and body somewhere I can read them.) Can I do this with nginx? Alternatively, is there some HTTP server that allows me to do this out of the box, to which I can proxy these requests by the means of nginx? Update: Note that this box has a bunch of normal traffic, and I would like to avoid capturing all of it on low level (say, with tcpdump) and filtering it out later. I think it would be much easier to filter good traffic first in a rewrite rule (fortunately I can write one quite easily in this case), and then deal with bogus traffic only. And I do not want to channel bogus traffic to another box just to be able to capture it there with tcpdump. Update 2: To give a bit more details, bogus request have parameter named (say) foo in their GET query (the value of the parameter can differ). Good requests are guaranteed not to have this parameter ever. If I can filter by this in tcpdump or ngrep somehow — no problem, I'll use these.

  Read the article

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Under FreeBSD, can a VLAN interface have a smaller MTU than the primary interface?

  - by larsks

  I have a system with two physical interfaces, combined into a LACP aggregation group. That LACP channel has two VLANs, one untagged (the "native vlan") and one using VLAN tagging. This gives us: lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether 00:25:90:1d:fe:8e inet 10.243.24.23 netmask 0xffffff00 broadcast 10.243.24.255 media: Ethernet autoselect status: active laggproto lacp laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3<RXCSUM,TXCSUM> ether 00:25:90:1d:fe:8e inet 10.243.16.23 netmask 0xffffff80 broadcast 10.243.16.127 media: Ethernet autoselect status: active vlan: 610 parent interface: lagg0 Is it possible to set a 9K MTU on lagg0 while preserving the 1500 byte MTU on vlan0? Normally I would simply try this out, but this is actually on a vendor-supported platform and I am loathe to make changes "behind the back" of their administration interface. This system is roughly FreeBSD 7.3.

  Read the article

• Can I connect a Playstation 3's HDMI output to my monitor's DVI-D input? [migrated]

  - by HankJDoomstorm

  I'm attempting to connect my Playstation 3 to my computer monitor. The monitor has a DVI-D (dual link) input, so before distinguishing between the different DVI varieties, I bought a DVI-I (dual link) to HDMI converter that won't fit into the port on the monitor (not only that, there isn't enough physical space in the back of the monitor to fit that much stuff before it hits the bottom of it). So I grabbed a DVI-D (single link) cable and got a female-to-female DVI-I coupler, and plugged the DVI-D cable into the monitor and the whole mess of converters. The end result was HDMI to DVI-D single link, but my monitor isn't receiving a signal on its digital channel. (For clarity's sake: DVI-D DL input on Monitor, DVI-D SL cable, DVI-I DL female-to-female coupler, DVI-I DL to HDMI converter, HDMI output on PS3) I don't know much about this stuff (obviously), but my educated guess is that the bandwidth of the PS3 is too high for the DVI-D Single Link cable, so nothing's getting through. Will replacing the single link cable with dual link resolve this? If not, is it possible at all? Oh, I should mention I'm aware I won't get audio through the monitor. I have an RCA to 3.5mm converter for that.

  Read the article

• Unable to access site over HTTPS using self signed certificate

  - by James

  I am developing a REST API which I want to secure with SSL/TLS. I have implemented a large part of the API which I have tested over HTTP, however, I am now at the stage where I want to switch it over to use HTTPS. At the moment the API is hosted on a Windows XP professional SP2 box running IIS 5.1 (development environment only) and I used the SelfSSL.exe tool from the IIS 6.0 Resource Kit Tools to generate a server certificate. I then configured my API to use this certificate which all appeared to work fine as I attempted to connect to my API using HTTP and I get a 403 response saying "... must be accessed over a secure channel...". However, the problem is when I attempt to access the same the API over HTTPS it just appears to hang! As this is a development environment at the moment I don't have a domain name (just a static IP address) and the API is running on port 81. Also (incase it matters) the API is the default site (I replaced it). Any ideas why I can't connect using HTTPS?

  Read the article

• Disabling LDAP Signing on Windows PDC in Local Policy

  - by Golmaal

  I just tripped over my own feet it seems. Playing around on a Windows 2008 R2 server (set up as domain controller), I was intrigued by certain warning event (event id 2886) which says: "To enhance the security of directory servers, you can configure both Active Directory Domain Services (AD DS) and Active Directory Lightweight Directory Services (AD LDS) to require signed Lightweight Directory Access Protocol (LDAP) binds." So I thoughtlessly did some Googling and set the relevant policies which enforce LDAP signing. Now I don't remember but I may have done that using Local Policy. Now I have setup a pfsense box which must authenticate AD users via LDAP. While the firewall can communicate over secure channel, it is difficult to manage the same for other packages such as Squid and SquidGuard. So now I have to disable i.e. undo those policy changes. The problem is that they are greyed out! The policies in question are LDAP server signing and LDAP client signing. I don't remember what I did but when I access these policies from Local Policy editor on the server, they are set to "Require Signing" and are greyed out. The same policies can still be set via Default Domain Controller option in Group Policy editor. So how can I reset these greyed out policies? Thanks

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• Photoshop CS4. How do I make sure my color stays the same in my different .psd files? (could be RGB

  - by Kris

  I asked 2 photoshop experts I know but they haven't got a clue because all my settings are exactly the same, in both files. (except the RGB type !! I'm not sure. Please read on) I use RGB color, 72DPI, 8 bits / channel. No adjustments (filters, like greyscale, etc ...) are selected / used. The layers are both normal, and opacity and fill are 100% (yes, in both files). I took two screenshots, and you can see the difference: http://www.flickr.com/photos/30465871@N05/4623864297/ http://www.flickr.com/photos/30465871@N05/4624469754/ Both colors are ff795d, but that doesn't matter, any color I use gives me the same problem: they both look different. Now, I know the CMYK settings (see screenshots) are different, but when the settings are the same the color changes. Why is this happening and how do I solve this problem? My guess is I'm working with different a type of RGB. It's sRGB IE61966 - 2.1 in the file I created (file info raw data) but I can't find that in the file that started with a screenshot. If that's the problem, how do I change / convert the RGB, once the file is already open? Thank you.

  Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126  | Next Page >