Search Results

Search found 312 results on 13 pages for 'esx'.

Page 12/13 | < Previous Page | 8 9 10 11 12 13  | Next Page >

• Cisco SG200 vlan issue in ESXi VSA cluster

  - by George

  I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

  Read the article

• Poor NFS Performance: OpenFiler

  - by Safin09

  Good Day Everyone, I have an issue with OpenFiler, a Linux-based operating that converts a computer system into a SAN/NAS appliance. Here is the problem. In my environment we have two Netapp Storevault 500 appliances that I normally perform backups to a NFS share. There are two backup cronjobs that use ghettoVCB to backup two groups of VM's. One group is a pool of 3 VMs. This takes 13 mins to complete. A second job that backups a pool of 5 VMs to a 2nd Storevault appliance which takes 2 hours. We then installed Openfiler on a old server that has 2 core Xeon processors. There is a software RAID 5 process in place. When performing the same backups to a NFS Openfiler share, the first backup job, which takes 13 mins, takes around 4 hours. The second backup job, which takes 2 hours, takes almost 10 hours to complete. This is unacceptable!!!! Especially considering the strain placed on the host ESX Server. I assumed that because of the software RAID 5, the overhead on the CPU explained the long backup times. I then installed Openfiler on a 2nd server, an IBM x306 machine which has a P4 Intel processor. This time no software RAID or any RAID at all. A single 750GB hard drive that contained the OS and the rest of the disk uses to backup VMs to a NFS share. I performed the first backup job of the pool of 3 VMs. This time the backup job took 1 and 1/2 hours to complete instead of 13 mins!!!!!!!!!! Is Openfiler simply poor at being an NFS Server!!!!!!!!!!!!! Has anyone else had these issues with Openfiler?

  Read the article

• ZFS - destroying deduplicated zvol or data set stalls the server. How to recover?

  - by ewwhite

  I'm using Nexentastor on a secondary storage server running on an HP ProLiant DL180 G6 with 12 Midline (7200 RPM) SAS drives. The system has an E5620 CPU and 8GB RAM. There is no ZIL or L2ARC device. Last week, I created a 750GB sparse zvol with dedup and compression enabled to share via iSCSI to a VMWare ESX host. I then created a Windows 2008 file server image and copied ~300GB of user data to the VM. Once happy with the system, I moved the virtual machine to an NFS store on the same pool. Once up and running with my VMs on the NFS datastore, I decided to remove the original 750GB zvol. Doing so stalled the system. Access to the Nexenta web interface and NMC halted. I was eventually able to get to a raw shell. Most OS operations were fine, but the system was hanging on the zfs destroy -r vol1/filesystem command. Ugly. I found the following two OpenSolaris bugzilla entries and now understand that the machine will be bricked for an unknown period of time. It's been 14 hours, so I need a plan to be able to regain access to the server. http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6924390 and http://bugs.opensolaris.org/bugdatabase/view_bug.do;jsessionid=593704962bcbe0743d82aa339988?bug_id=6924824 In the future, I'll probably take the advice given in one of the buzilla workarounds: Workaround Do not use dedupe, and do not attempt to destroy zvols that had dedupe enabled. Update: I had to force the system to power off. Upon reboot, the system stalls at Importing zfs filesystems. It's been that way for 2 hours now.

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• To update or to not update?

  - by Massimo

  Since starting working where I am working now, I've been in an endless struggle with my boss and coworkers in regard to updating systems. I of course totally agree that any update (be it firmware, O.S. or application) should not be applied carelessly as soon as it comes out, but I also firmly believe that there should be at least some reason if the vendor released it; and the most common reason is usually fixing some bug... which maybe you're not experiencing now, but you could be experiencing soon if you don't keep up with . This is especially true for security fixes; as an examle, had anyone simply applied a patch that had already been available for months, the infamous SQL Slammer worm would have been harmless. I'm all for testing and evaluating updates before deployng them; but I strongly disagree with the "if it's not broken then don't touch it" approach to systems management, and it genuinely hurts me when I find production Windows 2003 SP1 or ESX 3.5 Update 2 systems, and the only answer I can get is "it's working, we don't want to break it". What do you think about this? What is your policy? And what is your company policy, if it doesn't match your own?

  Read the article

• How does the LeftHand SAN perform in a Production environment?

  - by Keith Sirmons

  Howdy, I previously asked this ServerFault question: Does anyone have experience with lefthands VSA SAN The general consensus looks like it does not perform well enough for a production SQL server even at a light load. So the new question is, How does LeftHand's SAN perform on the HP or Dell dedicated Hardware boxes? We are looking at the Starter SAN with 2 HP nodes in a 2-way replication, 2 ESX servers hosting a total of 2 Active Directory server, 1 MS SQL server, 1 File Server, and 1 General Purpose Server for things like Virus Scan (All Microsoft Server 2005 or 2008). The reason I am looking at LeftHand is for the complete software package. I plan to have a DR site and like how the SAN can perform an Async Replication to the offsite location without having to go back to the Vendor for more licenses. I also like the redundancy built into the Network Raid architecture. I have looked at other SANS and found different faults with them. For example, Dell's EqualLogic: Found that although the individual box is very redundant in hardware, the Data once spanned across multiple boxes is not redundant, if a node goes down you have lost the only copy of the data sitting on that hardware (One thing is certain, all hardware fails... When? is the only question.). I have used an XioTech SAN as well.. Well worth the money BTW, but I think it is overkill for the size of the office I am targeting. The cost to get the hardware redundancy in the XioTech makes it a little out of reach for the budget I am working in. Thank you, Keith

  Read the article

• Two large, linked Excel files take 30 minutes to save, except in VMWare environment

  - by Gerald L

  I support some tax consultants who love to use Excel when they should probably be using Access. Anyway, they have created two Excel files, A and B. File B has cells linked to file A. File A is 27 MB and file B is 16 MB. One worksheet has roughly 1 million rows and there is another worksheet doing a whole bunch of SUMIF on the 1 million rows. Not the best idea, but whatever. Both Excel files open and recalculate within a reasonable amount of time (1-2 minutes). For a files that large, this is acceptable. Here is the problem: Once you change a cell, and save the file B, it takes a solid 30 minutes to save the file, and the processors are going full speed. I've tried this on 6 different machines, all running Windows XP SP3 with Office 2007 SP2 and all patches. The specs vary from one machine with 512 MB or RAM to a machine with 4 GB of RAM and quad processors. Same result every time. Here is the clincher: If I do this same save operation on a VMWare virtual machine, the file gets saved in 1 minute. I've tried this with my ESX servers at the office, my Mac Fusion at home, and VMWare workstation at the office. It does not matter how much RAM the virtual machine has... it saves in about 1 minute every time. Does anybody have any idea why this is happening and how to fix?

  Read the article

• Virtualization and best hardware sharing scenario for me

  - by azera

  Hello, Following this thread on super user, I now want to start installing all my vm on the hardware. As a remainder, i have a (powerful enough) server on which i want to install 3 OS: there is a debian (general dev testbed purposes), an ipcop (network control/firewall) and a freenas (local network file sharing). I'm wondering which scenario would be the best for me and if I will be able to share the hardware to do what i want; either a - install an hypervisor like the free vmware esx and all three vms in it, or b - install debian, and the other two running inside it with virtual box My need being that: the ipcop should handle all network traffic to the internet, meaning all traffic from my main computer but also all traffic from the other two vm the freenas shares should be accessible from the other two vm and my main computer too i don't really care about the debian access, i only need to access it from my main computer, not the other vms Will I need to install additionnal network cards for each vm or can they all share the same one happily ? (right now I have two, one linking the server to my router [which only ipcop is gonna use] and one linking it to my switch [which i would like all three to use]) As for harddrives, I was going to use 1 harddrive cut in 3 partitions to install all three OSes, then add to that the freenas drives, will it be correct ? Thanks a lot for anyone who can help me, this is kind of a vast area and I'm not sure which way to go at all

  Read the article

• ADO 2.8, VMWare and SQL Server - sudden bulk dropped connections

  - by CodeByMoonlight

  We have an overworked server currently running a single SQL Server 2000 instance on physical hardware, and about 40 different apps interact with it on a daily basis. Last year, the RAID controller failed and we had no spare, so IT Support hurriedly migrated it overnight to a copy running on a VMWare Server. While it was on that server everything ran much quicker due to it being a big improvement in spec. However, the biggest app using it had occasional serious errors which never occurred on physical hardware. Specifically, several times a week it would disconnect batches of users - anywhere from just ten to hundreds at once, and all at the same time. It didn't affect any particular users or PCs or offices - all were affected equally. The only common thing was the app, which is a VB6 app using ADO 2.8 to connect. The other apps connecting to that virtualised instance of SQL Server seemingly had no problems, although they were (and are) responsible for only a tiny fraction of the work involving this server. The upshot is that after about two weeks of loving the speed and hating the random mass disconnections (which we were never able to find a cause for), we sadly took the decision to return to physical hardware and the disconnections vanished. Now we've reached the point where the old server just can't handle all that's being asked of it, and we're intending to migrate everything to 2 or more other servers. The snag is that there's a good chance they'll have to be virtual ones again. Given what happened last time, I'm trying to find out what possible reasons there could be for these mass disconnections. We were running VMWare ESX, but the network is Novell-based. Also, the server had a linked server setup to connect to an Informix server using a known-to-be-buggy ODBC driver, and this is used throughout the day. Any ideas on the cause(s)?

  Read the article

• Routing for Two Hosts Behind a IPSec Tunnel

  - by Brent

  Network A 10.110.15.0/24 Firewall is .1 Host A is .2 Network B 10.110.16.0/24 Firewall is .1 Host B is .2 Two Cisco ASA's. IPSec tunnel with a crypo map that secures 10.110.15.0/24 <- 10.110.16.0/24. Let's say two hosts, 10.110.15.2 and 10.110.16.2 need to talk to each other. Normally I have to enter a persistent static route on a each host along the lines of: route add 10.110.16.0 mask 255.255.255.0 10.110.15.1 metric 1 -p (on the "A" box) I also have to enter another persistent static route on the .16 host in order for the traffic to know how to get back to the .15 network. Note that the default for each machine IS the firewall, so .1. I have no problem adding persistent routes on Windows/ESX/*nux machines but what about a smart switch in the .16 network that I want to manage from the .15 network. Do I need to run a routing protocol? Do I need to have Reverse Route Injection enabled on both ends of the IPSec tunnel? Should I add a route on the firewall? If so, how do you formulate it? Does it get a metric of 1 and my default route 0.0.0.0 get a metric of 2?

  Read the article

• Very uneven CPU utilization with SQL Server 2012 on 2 processor computer with 16 cores / processor

  - by cooplarsh

  After installing SQL Server Enterprise 2012 with the Server + Cal license model, on a computer with 2 processors each with 16 cores (and no hyperthreading involved) and putting the server under extremely heavy load the 16 cores on the first processor were very underutilized, the first 4 cores on the 2nd CPU were heavily utilized, and the last 12 cores were not used at all (because of the 20 core limit for this sql server version). Total CPU utilization was displaying as around 25%. Unfortunately, the server suffered from extremely poor performance even though if the tasks were evenly distributed across the 20 cores it wouldn't have been anywhere near as bad. The Windows Server was running on a VMWare virtual image under ESX Server, but all of the CPU was allocated to the windows server. We tried changing affinity settings (e.g., allocating most cores to CPU and the others to I/O), but that didn't help solve the performance problems. Upgrading the product edition to SQL Server Enterprise Core 2012 not only allowed the SQL Server to utilize the 12 previously unused cores on the 2nd processor, but it also resulted in a much more even distribution of tasks across all of the processors. To get through the backlog of requests cpU utilization jumped to around 90%, and then came down to around 33% once it was caught up, but performance improved dramatically since we failed over to the newly updated version And the performance issues went away. I was wondering if anyone knows what might cause SQL Server to unevenly distribute the load, relying almost exclusively on the first 4 cores of the 2nd processor that had 12 cores idle, and allocate only a few tasks to each of the 16 cores on the first processor. Also, is there any way we could have more evenly distributed the load across the 20 cores that were being used without the product edition upgrade? The flip side of that question is what did the product upgrade do that caused SQL Server to start evenly distributing the load across all of the cores that it recognized? Thanks to any insight to answer these questions and/or links that might help me better understand how to make sense of what was happenings.

  Read the article

• Remove server hangs, gets stuck. How to debug?

  - by bibstha

  I have an vps running on VmWare ESX with Ubuntu 8.04 LTS. It has been running smoothly for the past 3 months, however recently we've notices two strange bugs. a. The server hangs, today was second time. The nature of the hang is very strange. I can ping to the server server, it sends back response fine. However all other services like sshd, apache, mysql etc do not respond at all. When working, telnet servername 22 Escape character is '^]'. SSH-2.0-OpenSSH_5.X Debian-5ubuntu1 And other web services would run fine. When its hung, I can make tcp connections to 22 as well as 80 but receive no response at all. telnet servername 22 Escape character is '^]'. How can I debug this problem? Is there any daemons I can run that will periodically log status? Please tell me as to how to proceed with it. b. The another strange problem is that, of lately I am unable to transfer files larger than around 100KB, smaller files of around 1-2 KB works file. scp anotherserver:filename . or wget http://www.example.com/file would get stuck. There is still around 6GB of space remaining, so I don't think that is an issue. Any pointers where I should look into?

  Read the article

• OpenVPN Server - CPU is pegged out

  - by ericl42

  Hello, I am configuring OpenVPN to act as a SSL tunnel for a remote location. I have OpenVPN1 at our current location acting as a server then OpenVPN2 at the other location that is acting as a client but is also acting as a DHCP server to machines behind it so they are basically connected to the local LAN. Everything is set up fine and I can talk from location A to location B with no problems like everyone is local. I am however having some performance issues. OpenVPN1 CPU is pegged to 100% the entire time I am copying or doing any type of activity through the tunnel. I expect some CPU usage going up but nothing like this. It's really killing my performance. OpenVPN1 is running in ESX right now with 2 gig RAM and 4 procs with unlimited bursting capacity. I am using AES-192 encryption with a 1024 key. Any idea how I can get my CPU down on OpenVPN1 and my download/upload speeds higher between the tunnel? Thanks. edit: Turning down the logging helped boost the throughput a little bit, but I am still fairly shy of where I believe I should be. Also I am still maxed out on the CPU. Does anyone have any ideas? I am really stuck on this. Thanks.

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• How to interpret iozone values

  - by Henno

  I ran a test to measure my I/O IOPS on Linux: iozone -s 4g -r 2k -r 4k -r 8k -r 16k -r 32k -O -b /tmp/results.xls iozone claims that output is in operations per second yet the numbers are too big for that to be plausible. I'm observing some 320 CMDs/s maximum on vmware esx console (esxtop, then v). File size set to 4194304 KB Record Size 2 KB Record Size 4 KB Record Size 8 KB Record Size 16 KB Record Size 32 KB OPS Mode. Output is in operations per second. Command line used: iozone -s 4g -r 2k -r 4k -r 8k -r 16k -r 32k -O -b tmpresults.xls Time Resolution = 0.000001 seconds. Processor cache size set to 1024 Kbytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride KB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 4194304 2 19025 5580 27581 29848 284 198 415 1103217 1498 18541 4340 24245 25618 4194304 4 15650 21942 18962 21068 252 1198 193 976164 1677 22802 23093 21089 21232 4194304 8 11121 11638 10273 10165 247 1196 202 625020^C The test ran for 15 hours before I pressed ^C. Is that ordinary expectation for such command line (dedicated 4 drive RAID10 LUN, 10k RPM SAS drives in EMC CX300)?

  Read the article

• How does Linux determine the SCSI address of a disk?

  - by Chris Sears

  Greetings, I'm working with RHEL 5.5 guest VMs under VMware ESX 4. When I configure the virtual disks in the VM hardware settings, each disk has a SCSI address in the format "N:M". For example, "1:3" would mean SCSI host number 1 and SCSI target ID 3. When I look at the disk info from the VM's BIOS or a Windows OS, the detected SCSI address info matches up with the virtual hardware settings. But under Linux, the SCSI address components don't match up, at least not completely or consistently. I've tried the three supported virtual SCSI and SAS drivers and they all seem to be "broken", but in different ways. Here's a list of the virtual hardware addresses vs what was detected under Linux with each of the drivers: Driver vHW Addr Linux Addr -------- -------- ---------- LSI SAS 0:0 0:0 LSI SAS 0:3 0:1 LSI SAS 0:6 0:2 LSI SCSI 1:1 2:1 LSI SCSI 1:4 2:4 LSI SCSI 1:7 2:7 pvSCSI 2:2 1:2 pvSCSI 2:5 1:5 pvSCSI 2:8 1:8 My main question is why does this happen under Linux? The next question is: how do I get it fixed or fix it myself? If I was going to guess, I'd say it's an issue with how the kernel is handing out the SCSI host number and how the Linux SCSI driver (included with VMware tools) is detecting the SCSI target number. Perhaps the order the drivers are loaded also has something to do with the issue. I'm guessing this would not involve udev, but I could be wrong. Any thoughts would be appreciated. Thanks! PS. My environment is VMware, but I don't need an answer for these drivers specifically. I imagine this might be a problem with any SCSI driver under Linux.

  Read the article

• Windows 2012 RDS Temporary profile for Administrator

  - by Fabio

  I've configured a Windows 2012 RDS Farm with two virtual servers (VMWare - each one on a different ESX server). Both servers have Licensing, Web Access, Gateway, Connection Broker and Session Host roles. High Availability is set up and it works fine. Remote Apps are working and even Windows XP clients have access to the web interface. User profile path is \vmfiles1\UserProfileDisks\App\ and almost everyone has full right access to it. The problem I have is that I would like to be able to access both servers at the same time with the Administrator account (console), but each time I try, the second server that I logon to give me access with a temporary profile. I tried to enable/disable multiple sessions per user and forced Admin logoff with the GPO but nothing changed. Another thing is that the server pool is not saved, so each time I restart the RDS server or I logoff from it, I have to add a server in the server manager. Do you have any idea? Sorry if my english is not perfect.

  Read the article

• VMware NAS/iSCSI recommendations - smallish organization

  - by Bubnoff

  I have two VMware servers - ESX + ESXi. Two backup NAS boxes. The current NAS boxes are low-cost and unsuitable for running VMs from. Support NFS only. Slow. My plan is to have a dedicated iSCSI/NAS for storing and running VMs. Two additional low-cost boxes for backup. I'm looking for advice regarding 2 things really: Recommendations as far as VMware architecture/design for a smaller organization. Less than 20 Virtual Machines. 2 servers + 2 x 1.5 terabyte backup NAS boxes. A good NAS/iSCSI box with your recommendation on RAID config ...I would go with 6 or better. I'm trying to design an installation that is both fast and reliable/redundant. If you have any experiences to share or your current configuration including network design ( switches, fiber ...etc ), I will be enormously thankful. I'm not married to this idea, so if you have a design not using iSCSI NAS boxes ...let er rip. Cost? Can we stay around $5,000 ( on top of already stated components )? Links to info are welcome also. Thanks for reading! Bubnoff

  Read the article

• How to replicate a windows servers (IIS,Files,ConfigurationState)?

  - by Geo

  Maybe a better question is: What is the closest competitor for DoubleTake? I am looking to replicate a windows production server in case it fails have a immediate backup. Any idead? NOTE 1: I forget to add that this server is on the EC2 Amazon Cloud. NOTE 2: The main situation we have is recreating the configuration settings like IIS, FTP Server, SQL Server, SVN Server. NOTE 3: So far I have been giving three options as answers for my original question: AppAssurance -- After talking to their sales team they do not support Amazon as cloud provider. Basically there is a technical need to be able to reboot from a disk or similar media. So ESX Virtual machine environment will work, but not the EC2. Acronis -- which works as a backup in ghost style. This will work for other type of scenarios. Use the Amazon EC2 API -- This option is ideal, but only works if you are developing a cloud application rather than hosting a regular application in a cloud scenario. This means that I am still looking for the answer. Any other ideas.

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• Window Server 2003 Print spooler

  - by mikenardone

  Hello Everyone in ServerFault, I am new to this website. I have been coming here to fix my own problems. I believe everyone here on this website is great. I could not find this issue anywhere. I am sure that other people had this issue. I have IBM X3850 48GB ram 2 TB of hard drives, four NIC cards. 2 Xeon 1.7 CPU. I am running VMware ESX. I believe that was the paid version if not then it is ESXI. I have 7 Servers on this server. All Window server 2003. On one of the Servers I keep on getting CPU is at 100% . So when I go into task manager and look at the processes that is going on, it is my print spooler. I have 30 different HP laserjet printers and two copiers from HP. I believe it is an driver issue, but I can't figure with one is doing this. Is there any programs for window server 2003 that finds bad print drivers.

  Read the article

• Do background processes get a SIGHUP when logging off?

  - by Massimo

  This is a followup to this question. I've run some more tests; looks like it really doesn't matter if this is done at the physical console or via SSH, neither does this happen only with SCP; I also tested it with cat /dev/zero > /dev/null. The behaviour is exactly the same: Start a process in the background using & (or put it in background after it's started using CTRL-Z and bg); this is done without using nohup. Log off. Log on again. The process is still there, running happily, and is now a direct child of init. I can confirm both SCP and CAT quits immediately if sent a SIGHUP; I tested this using kill -HUP. So, it really looks like SIGHUP is not sent upon logoff, at least to background processes (can't test with a foreground one for obvious reasons). This happened to me initially with the service console of VMware ESX 3.5 (which is based on RedHat), but I was able to replicate it exactly on CentOS 5.4. The question is, again: shouldn't a SIGHUP be sent to processes, even if they're running in background, upon logging off? Why is this not happening? Edit I checked with strace, as per Kyle's answer. As I was expecting, the process doesn't get any signal when logging off from the shell where it was launched. This happens both when using the server's console and via SSH.

  Read the article

• Migrating WebLogic 10.3.0 to new host. Slow managed server startup times

  - by wadevondoom

  We are migrating our Blue Martini Commerce application (only supported on WebLogic 10.3.0) to a new host (Redhat 6.3 on a VMWare ESX vm). We are seeing extremely slow start up times for our managed server(s) that is basically 20x slower than our current production. As a for instance the Publish managed server takes ~30 - 45 seconds in current production and in the new environment it takes ~10 minutes. The setup uses the same domain structure and JVM as the current production environment. The same setup files are used. We use jdk1.6.0_33 on 64 bit architecture. We used the generic 64bit weblogic installer and used pack / unpack utilities to migrate the domain. The JAVA_OPTS to start this server are: "-d64 -Xms256m -Xmx512m -XX:PermSize=48m -XX:MaxPermSize=256m" The sysadmins have checked /etc/sysctl.conf and /etc/limits.conf to ensure we were not hitting some kind of process limit. As I am not sure what this managed server does from a Blue Martini perspective during the phase of startup I also had the DBA check to ensure that Oracle RAC (11.2.0.3) wasn't also hitting some kind of process limit or if there was a tns listener issue. The new host is quite a bit stricter with their server lock downs so there are a few differences.... Redhat 6.3 in new env, RH 5.7 in current SElinux is targeted in new env and disabled in current VM in new env and dedicated hardware in current iptables disabled in current. It was enabled in new prod but I had them disable it just in case I apologize for not being more specific. I am mostly hoping got some tips. I do not have the typical root access I would normally have in this environment. I am just hoping got a path forward. I did a few 'kill -3' to see if there are blocked threads and I got nadda. The service works for all intents and purposes it is just painfully slow. Thanks you all in advance for reading and best regards. Wade

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• how to import existing VM in vmware workstation 8 inventory

  - by Wimmel

  I like to add existing vmware (player) virtual machines to the vmware workstation 8 inventory on linux. When I create a new virtual machine, it is stored in /var/lib/vmware/Shared VMs/. But copying new directories to that folder, does not make them appear in the workstation window. I found out, the inventory is stored in /etc/vmware/hostd/vmInventory.xml; <ConfigRoot> <ConfigEntry id="0000"> <objID>1</objID> <vmxCfgPath>/var/lib/vmware/Shared VMs/test 1234/test 1234.vmx</vmxCfgPath> </ConfigEntry> </ConfigRoot> But I don't know if I break anything when adding entries myself, and giving it an unique ID. Besides, adding a large number of VMs this way is a bit cumbersome. On ESX, it was possible to use vmware-cmd -s register, but I don't have a vmware-cmd installed. In another question it was suggested to use vmware converter. But vmware converter 5 (on windows) only allows a destination file location when I select workstation as destination type. When I select vmware infrastructure as destination type, it says the destination is unsupported; it required vmware vcenter server.

  Read the article

< Previous Page | 8 9 10 11 12 13  | Next Page >