Search Results

Search found 7940 results on 318 pages for 'intel wireless'.

Page 12/318 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • strange behaviour - dhclient needs to be run twice in order to connect to wireless

    - by splicer
    I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

    Read the article

  • Terrible ping time with TP-Link wireless router

    - by rabbid
    I am literally a foot away from this useless TL-WR340G/TL-WR340GD router and check out this ping time: 64 bytes from 192.168.1.8: icmp_seq=291 ttl=64 time=9477.516 ms 64 bytes from 192.168.1.8: icmp_seq=292 ttl=64 time=8954.423 ms 64 bytes from 192.168.1.8: icmp_seq=293 ttl=64 time=8262.836 ms 64 bytes from 192.168.1.8: icmp_seq=294 ttl=64 time=7937.853 ms 64 bytes from 192.168.1.8: icmp_seq=295 ttl=64 time=7517.768 ms 64 bytes from 192.168.1.8: icmp_seq=296 ttl=64 time=7106.063 ms 64 bytes from 192.168.1.8: icmp_seq=297 ttl=64 time=6492.109 ms 64 bytes from 192.168.1.8: icmp_seq=298 ttl=64 time=5835.305 ms 64 bytes from 192.168.1.8: icmp_seq=299 ttl=64 time=5314.897 ms 64 bytes from 192.168.1.8: icmp_seq=300 ttl=64 time=4902.705 ms 64 bytes from 192.168.1.8: icmp_seq=301 ttl=64 time=4716.959 ms 64 bytes from 192.168.1.8: icmp_seq=302 ttl=64 time=5224.450 ms 64 bytes from 192.168.1.8: icmp_seq=303 ttl=64 time=5024.079 ms 64 bytes from 192.168.1.8: icmp_seq=304 ttl=64 time=5044.100 ms 64 bytes from 192.168.1.8: icmp_seq=305 ttl=64 time=4477.990 ms 64 bytes from 192.168.1.8: icmp_seq=306 ttl=64 time=3582.432 ms 64 bytes from 192.168.1.8: icmp_seq=307 ttl=64 time=2911.896 ms At this time mine is the only computer using the router. This happens from time to time. I'd restart the router, and then it'll have a 1-2 ms ping for a while, and then back to terrible ping. Is it just a poor quality router? Suggestions? Thank you

    Read the article

  • Erratic WiFi 2.4 GHz channel spikes, what gives?

    - by Francis W. Usher
    Sorry guys, first a gripe about my neighbor's WiFi access point (it is related): they totally hog the center nine 2.4 GHz channels (3-11), centered right at 7! I know the outer regions of the signal don't make as much of a difference, and technically they're running channels 5 & 9. Anyway, their signal is clearly interfering with mine, which is necessarily centered at 3 or 11 to evade their interference. I guess it's somewhat a case of access point envy: they happen to have both a stronger signal and a higher data rate, while occupying twice the band width that I do. Getting to the point, I've noticed that they tend to sit nice and pretty centered at 7, but they definitely auto-select their channel, and I've noticed that the auto-selection algorithm tends to shift towards the higher channels; hence I decided to pick channel 3, and I don't get so many intermittent lag spikes any more. Anyway, the thing that weirded me out was the reason they have to auto-select sometimes: unexplained, powerful (talking order of 0dB here), giant spikes of 2.4 GHz activity in consistent regions of the spectrum. I don't think it's just noise, since my wireless monitoring software is registering a MAC address, a manufacturer, and usually a fairly coherent ascii name... and it seems to be a fairly well-confined signal. But these signals are fairly common, and they do some weird stuff to my signal. So my question is what are these signals? Where are they coming from? Where are they going? Why are they so ridiculously strong? Why don't they ever last very long? Here's an inSSIDer screenshot I took, for your perusal. I am labeled with "me", my greedy neighbor labeled with "neighbor", and the 2 quasar signals are labeled with "WTF?".

    Read the article

  • How to re-configure graphics from Intel integrated to Intel / ATI switchable?

    - by Bucic
    There are lots of 'how to get switchable graphics to work' guides but I found none on how to configure a system for switchable graphics operation on Ubuntu from the ground up, nor explaining the current driver situation for particular computer models (integrated+discrete combinations). Example: https://help.ubuntu.com/community/HybridGraphics My system being mature and on Intel integrated card also makes things complicated. System information: Ubuntu 12.04 amd64, installed clean with system configured to use only the integrated Intel card Lenovo Thinkpad T500 Intel GMA 4500MHD / ATI Mobility Radeon HD 3650 Current situation: Mature and up-to-date system with no configuration changes to what's given above. I've made a backup image of the system (Clonezilla) so regardless of what's written below let's assume it's our starting point. If something in What I have already tried is not clear you may as well diregard it. What I have already tried: Configuring BIOS to switchable graphics and: Installing Additional Hardware drivers - returned an error. Installing proprietary amd-driver-installer-12.6-legacy-x86.x86_64.run automatically - system starts to 'low-graphics mode'. Tried fixing as per https://help.ubuntu.com/community/BinaryDriverHowto/ATI#Manually_installing_Catalyst_12.6.2C_special_case_for_Intel.2BAC8-ATI_hybrid_graphics Got lost, gave up. Please note that while configuring BIOS for integrated graphics only is pretty straightforward, configuring for switchable graphics is not.

    Read the article

  • My processor is not detected intel core 2 duo

    - by walid
    My processor is not detected intel core 2 duo When I type $uname -m -p I get this i686 unknown I have Ubuntu 10.10 netbook remix but the cat /proc/cpuinfo gives right identification of two processors as below processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping : 6 cpu MHz : 1826.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm dts tpr_shadow bogomips : 3657.99 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz stepping : 6 cpu MHz : 1826.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm dts tpr_shadow bogomips : 3657.53 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: The problem is with programs that uses more than one core like virtualbox and bitcoin which refuses to use more than one core Is there anythign wrong or anything that I can do? My installation is from a live usb iso on a USB

    Read the article

  • Ubuntu and bumblebee and intel problem

    - by LnxSlck
    I have a brain teaser that i can't solve. When 12.04 (64bits) came out, i did a fresh install and then installed bumblebee with: sudo add-apt-repository ppa:bumblebee/stable sudo apt-get install bumblebee bumblebee-nvidia And Ubuntu recognized (System Settings - Details) Intel Card for primary card, and i could launch applications with optirun. I have: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 520MX] (rev ff) Now, a few days back, i did the exact same thing, installed from the same DVD everything the same, installed bumblebee the same way. Nvidia with Optirun works fine, but Ubuntu doesn't have 3D effects: root@deathstar:~# optirun /usr/lib/nux/unity_support_test -p OpenGL vendor string: NVIDIA Corporation OpenGL renderer string: GeForce GT 520MX/PCIe/SSE2 OpenGL version string: 4.2.0 NVIDIA 295.40 Not software rendered: yes Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: no GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no I never did anything to install Intel drivers (except installing mesa-utils), before bumblebee got everything working, but now i can't get Ubuntu to get Unity with 3D. Can someone help me please get Unity 3d working? Your help will be much appreciated

    Read the article

  • Latest update to Ubuntu 13.10 broke Intel graphics drivers

    - by James Davies
    I'm running a copy of Ubuntu 13.10 on an i7-4771 w/ Intel HD4600 Graphics using a Dell Ultrasharp 1440p monitor via Displayport. Up until today this configuration has been working perfectly, however the latest update appears to have broken my graphics configuration, and xorg is now refusing to go above 1280p resolution. Running xrandr it appears the driver incorrectly thinks my monitor is plugged into the HDMI port and is detecting a max resolution of 1920x1200 instead of 2560x1440. (It's actually plugged in via Displayport). Based on the apt history.log, the latest update was for the kernel. I'm presuming the issue is that the official Intel driver hasn't been updated to support this version? Is there any way to resolve this, or will I need to upgrade to 14.10 to get the latest driver from Intel? Start-Date: 2014-05-28 11:30:57 Commandline: aptdaemon role='role-commit-packages' sender=':1.473' Install: linux-image-extra-3.11.0-22-generic:amd64 (3.11.0-22.38), linux-image-3.11.0-22-generic:amd64 (3.11.0-22.38), linux-headers-3.11.0-22:amd64 (3.11.0-22.38), linux-headers-3.11.0-22-generic:amd64 (3.11.0-22.38)

    Read the article

  • Cannot connect to secure wireless with Netgear wna3100 USB

    - by Vince Radice
    I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

    Read the article

  • Slow wifi on Ubuntu 12.04 wifi driver ath9k

    - by lunar
    For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

  • Unable to either locate any wireless networks nor even connect to wifi

    - by Leo Chan
    I'm new to Linux. I currently have installed ubuntu 12.10. I had a previous problem with my wireless card (see url to see previous problem : How to enable wireless in a Fujitsu LH532?). It now shows Connect to hidden network and create new wireless network but now unfortunately it simply cannot find any wireless connections. I did have a very thorough look around about this problem such as wait a little longer since sometimes it cannot load all the wireless connections available that quickly. My wifi is a hidden network and I have used the connect to hidden network feature but it keeps asking for my wep key which has been checked 4 times (I counted) and it still seems to not work; It keeps asking for the WEP key. I did try both WEP 40/128-bit key and WPA & WPA2 since previously on my windows it worked; My family later decided to use WEP. I only have a quick fix using a usb wireless stick and I wish to have a more solid fix. Thanks Results from sudo iwlist wlan0 scan wlan0 Scan completed : Cell 01 - Address: 00:1E:73:C8:62:BD Channel:6 Frequency:2.437 GHz (Channel 6) Quality=25/70 Signal level=-85 dBm Encryption key:on ESSID:"EnigmaHome" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000cb3bb10a5c Extra: Last beacon: 696ms ago IE: Unknown: 000A456E69676D61486F6D65 IE: Unknown: 010482848B96 IE: Unknown: 030106 IE: Unknown: 0706484B20010B1E IE: Unknown: 2A0107 IE: Unknown: 32080C1218243048606C IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 Cell 02 - Address: C8:3A:35:34:C1:60 Channel:6 Frequency:2.437 GHz (Channel 6) Quality=22/70 Signal level=-88 dBm Encryption key:on ESSID:"Tenda" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s Mode:Master Extra:tsf=000001336e70ffdd Extra: Last beacon: 716ms ago IE: Unknown: 000554656E6461 IE: Unknown: 010882848B961224486C IE: Unknown: 030106 IE: Unknown: 32040C183060 IE: Unknown: 0706434E20010D10 IE: Unknown: 33082001020304050607 IE: Unknown: 33082105060708090A0B IE: Unknown: DD270050F204104A0001101044000101104700102880288028801880A880C83A3534C160103C000101 IE: Unknown: 050400010000 IE: Unknown: 2A0106 IE: Unknown: 2D1AEC0117FFFF0000000000000000000000000000000C0000000000 IE: Unknown: 3D1606000500000000000000000000000000000000000000 IE: Unknown: 7F0101 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Preauthentication Supported IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00 IE: Unknown: 0B05010089127A IE: Unknown: DD1E00904C33EC0117FFFF0000000000000000000000000000000C0000000000 IE: Unknown: DD1A00904C3406000500000000000000000000000000000000000000 IE: Unknown: DD07000C4304000000 Cell 03 - Address: 00:1E:73:C8:62:BF Channel:6 Frequency:2.437 GHz (Channel 6) Quality=47/70 Signal level=-63 dBm Encryption key:on ESSID:"\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000cb3bac614e Extra: Last beacon: 1064ms ago IE: Unknown: 00110000000000000000000000000000000000 IE: Unknown: 010482848B96 IE: Unknown: 030106 IE: Unknown: 050C010200000000000000000000 IE: Unknown: 0706484B20010B1E IE: Unknown: 2A0107 IE: Unknown: 32080C1218243048606C IE: Unknown: DD070050F202000100

    Read the article

  • Networking- Wireless and Wired not working

    - by JJ White
    So everything in Ubuntu has been working great until networking stopped working. I've spent the better part of two days scouring for a fix with no luck. Here is my info...your help would so be appreciated. grep -i eth /var/log/syslog | tail Sep 25 16:31:59 jj-laptop NetworkManager[970]: <info> (eth0): cleaning up... Sep 25 16:31:59 jj-laptop NetworkManager[970]: <info> (eth0): taking down device. Sep 25 16:31:59 jj-laptop kernel: [23403.998837] sky2 0000:02:00.0: eth0: disabling interface Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): now managed Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): bringing up device. Sep 25 16:35:54 jj-laptop kernel: [23413.629424] sky2 0000:02:00.0: eth0: enabling interface Sep 25 16:35:54 jj-laptop kernel: [23413.635703] ADDRCONF(NETDEV_UP): eth0: link is not ready Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): preparing device. Sep 25 16:35:54 jj-laptop NetworkManager[970]: <info> (eth0): deactivating device (reason 'managed') [2] and then ifconfig -a eth0 Link encap:Ethernet HWaddr 00:17:42:14:e9:e1 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:4605 errors:0 dropped:0 overruns:0 frame:0 TX packets:287 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:315161 (315.1 KB) TX bytes:63680 (63.6 KB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13018 errors:0 dropped:0 overruns:0 frame:0 TX packets:13018 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:880484 (880.4 KB) TX bytes:880484 (880.4 KB) wlan0 Link encap:Ethernet HWaddr 00:13:02:d0:ee:13 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) also iwconfig lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extensions. and of course sudo lshw -C network *-network description: Ethernet interface product: 88E8055 PCI-E Gigabit Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 12 serial: 00:17:42:14:e9:e1 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A latency=0 link=no multicast=yes port=twisted pair speed=1Gbit/s resources: irq:44 memory:f0000000-f0003fff ioport:2000(size=256) memory:c0a00000-c0a1ffff *-network DISABLED description: Wireless interface product: PRO/Wireless 3945ABG [Golan] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: wlan0 version: 02 serial: 00:13:02:d0:ee:13 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl3945 driverversion=3.2.0-31-generic firmware=15.32.2.9 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:45 memory:c0100000-c0100fff last but not least lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 dm_crypt 22528 0 rfcomm 38139 0 parport_pc 32114 0 bnep 17830 2 ppdev 12849 0 bluetooth 158438 10 rfcomm,bnep binfmt_misc 17292 1 snd_hda_codec_idt 60251 1 pcmcia 39791 0 joydev 17393 0 snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80845 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 yenta_socket 27428 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event pcmcia_rsrc 18367 1 yenta_socket wacom_w8001 12906 0 irda 185517 0 arc4 12473 2 iwl3945 73111 0 iwl_legacy 71134 1 iwl3945 mac80211 436455 2 iwl3945,iwl_legacy cfg80211 178679 3 iwl3945,iwl_legacy,mac80211 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq dm_multipath 22710 0 pcmcia_core 21511 3 pcmcia,yenta_socket,pcmcia_rsrc psmouse 96619 0 apanel 12718 0 serport 12808 1 serio_raw 13027 0 crc_ccitt 12595 1 irda mac_hid 13077 0 snd 62064 15 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_t imer,snd_seq_device input_polldev 13648 1 apanel soundcore 14635 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm lp 17455 0 fujitsu_laptop 18504 0 parport 40930 3 parport_pc,ppdev,lp dm_raid45 76451 0 xor 25987 1 dm_raid45 dm_mirror 21822 0 dm_region_hash 16065 1 dm_mirror dm_log 18193 3 dm_raid45,dm_mirror,dm_region_hash sdhci_pci 18324 0 sdhci 28241 1 sdhci_pci sky2 49545 0 i915 414939 3 drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915

    Read the article

  • Wireless Network Found, can't connect, repeated requests for authentication

    - by Herm Holland
    After trawling through the internet, on forums, support websites, and through dozens upon dozens of answered questions on this site, I've not found a solution to what seems like a fairly regular problem... I cannot connect to a wireless network, and am continually asked for the network password. I have tried countless suggested solutions on the different locations I've already referred to. None of them have worked. Details of my experience are as follows: I have just recently installed Ubuntu 12.04.1 (32-bit). Ubuntu installed on my system seemingly fine, and I even formatted my hard drive during the process. It's as if it were a new desktop computer. During the installation I was asked to connect to a Wireless Network. I have a USB Wireless Card connected which I have used to connect desktop PC's, laptops, and a Wii to the internet from approximately the same area of the house (thus the same distance from the Wireless Router). I chose my network, entered the correct password for it (I double checked; it's definitely the right password) and proceeded with the installation. Several times before the installation was complete, I was asked to authenticate the connection, and this seemed to do nothing each time. On the repeated screens the password was already entered in the appropriate box. When Ubuntu booted up the first thing I was faced with (other than something about Language settings, or something) was another request for authentication. Again, the password was already there, so I clicked connect. It did not connect. Instead, I was once again faced with repeated requests every few minutes. I went onto my laptop, which is connected to this network, checked the details of the network, and entered them manually into my Ubuntu PC (including the IPv4 and IPv6 information) but this didn't work either, so I set it back to finding the settings automatically. Note, also, that the "Connect automatically" and "Available to all users" boxes are checked, and have been unchecked & rechecked countless times. I have also tried having my User account connect automatically, and to need a password entered at the welcome screen. Whilst I've been writing this, it has gone through a spat of connecting successfully to the network for less than a minute, before coming offline again, only to repeat the process. But it has now returned to prompting me for a password every couple of minutes. This computer has already run on the Fedora OS, and had no trouble connecting to, and maintaining a connection. I also have a laptop running Windows 7 less than a metre away from this desktop PC, which is connected and has no trouble maintaining a connection at 50%-100% strength (fluctuating). Therefore: - I know it's not the wireless card - I know it's not the PC itself - I know it's not the access point - I know it's not the location of my PC or wireless card - It is solely because of Ubuntu Everything else has worked fine, but the moment Ubuntu was introduced into the equation, it has gone completely wrong. Honestly; I prefer Ubuntu as an OS to Fedora, but if I can't solve the problem it'll be straight back to Fedora that I'll have to go. Can anyone help me at all?

    Read the article

  • Randomely loosing wireless connexion with Cubuntu 12.04

    - by statquant
    I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

    Read the article

  • Intel Rapid Storage / Smart Response SSD caching issue

    - by goober
    Background Recently built my own PC. It works! Almost. It's been a while since getting into the guts of these things, so I'm familiar but may be missing something simple. FYI, I don't care about blowing the OS away -- it's brand new and we can go back from scratch as many times as necessary. Goal / Issue I'd like to use the SSD to take advantage of Intel's Smart Response technology (allows the SSD to act as a cache for HDDs) I would like the SSD cache to act as a cache for my HDDs, which I would like to be in a RAID1 array (so I get the speed from the SSD and the redundancy from the RAID1) However, Windows only sees the drive in device manager (not as a drive), so I'm unsure what to do about that. Related: as far as I know, for this to work, the drives all have to be in a single RAID array (i.e. a RAID0 pairing of the SSD and the RAID1 HDD array). However, when attempting this at the BIOS level, I am told there is not enough space for an array. Steps so Far Moved the SSD onto the Intel controller (I'd had it on the Marvel 6.0 controller instead of the Intel controller, so the BIOS was only seeing it in a strange way) Updated the BIOS of the motherboard to the latest version Reinstalled Intel's RST (iRST?) software several times, as some forums reported it working after reinstalling 3 times (which does not inspire confidence). Checked Intel storage: it does see the SSD as a physical, non-RAID device. However, it says no space exists if I try to create an array. Checked the BIOS: it does not show up in the boot order, but is an option that can be selected under boot options. Tried the firmware update for that model. Issue: the firmware CD doesn't detect a drive; maybe the Intel storage controller is making it difficult? moved the ssd to the marvel controller. The firmware update cd appeared to hang while searching for drives. swapped out the SATA cable for the manufacturer's and moved back to the intel storage controller. Noticed at this point that in the Intel RST software, a device DOES show up in addition to the RAID set -- only shown as a "60 GB internal disk". Windows doesn't appear to see it as a drive, but it does still show in device manager. Move SSD to port from 0-3 on MOBO and set SATA mode to IDE (after disconnecting RAID1 config) to allow the firmware update to work. Firmware was already at the latest version. Next Steps ? Components involved ASUS P8Z68-V PRO motherboard (Intel Z68 Chipset) Intel i7 2600k Processor 2 x 1TB 7200 RPM HDDs 64 GB Crucial M4 SSD (M4-CT064M4SSD2) For Reference -- Storage Configuration Intel 3 gbps Intel 3gbps Intel 6gbps Marvel 6gbps +----------+ +----------+ +----------+ +----------+ | | <----+ | | +-+ | | | |----------| | |----------| |-|--------| |----------| | | | | + | | | | | | +----------+ | +--|-------+ +-|--------+ +----------+ | | | + v v | 1 TB HDD 64 GB SSD + +> 1 TB HDD For Reference -- Intel RST (v10.8.0.1003) Screenshot Don't mind the "rebuilding" -- knocked a power cable out at one point; it's doing its job, not an indicator of a bad HDD. Any thoughts? Thanks in advance for any help!

    Read the article

  • Switching from Onboard intel to Nvidia Dedicated GPU

    - by Anarkie
    How can I switch from Intel onboard grpahics to Nvidia Dedicated GPU? When I go to windows screen resolution I see intel. I cant change it. I go to Device Manager, I see both Adapters are there and Nvidia is known.I disabled intel, I didnt see any option to set one as primary so I disabled intel, black screen!Reboot and re-enable intel. I right click on the desktop, choose "Nvidia Control Panel" and on 3D options I chose the desired game I want to play, High performance Nvidia, but it didnt switch when I started the game. Then I made preferred GPU in the global settings High performance Nvidia for everything it still didnt change.I understand to save the battery etc. there is a switch option between these two but I dont see this switch when it is necessary, I cant also switch manually?Is there a manual switch FN key?I looked but couldnt find. Why I want to do this? 1) Better game peformance. 2) I want to play an old game from 2002(Diablo 2 LOD), when I start the game there are black bars on the sides, so screen becomes just smaller which I dislike!I heard this is intel's specification to center the display.But instead I would like to scale or expand it to fit widescreen(fullscreen).Which should be possible with Nvidia. My Notebook Specs: Fujitsu Lifebook AH531, Win7 , 64 bit, i5, intel HD graphics onboard, Nvidia GT 525. I didnt install Nvidia later, it was always installed and ready from the moment I turned on the computer first time. How I determined that the cards werent switched when I am playing the game: with the windows key I exited from the game, then looked at screen resolutions menu, still saw intel, also the game was still with black bars.I know intel GPU should enough for Diablo 2 but I am interested in this answer for further games, I dont always play Diablo, what if I install an up to date game for example?Then Intel will not be sufficient.I would like to learn the switch option.

    Read the article

  • Wireless connection by using command screen

    - by Amadeus
    I installed Ubuntu 12.04 armhf to my beagleboard-xm and now trying to connect to a wireless network. First, I checked if I can search for available networks: ubuntu@arm:~$ iwlist scan lo Interface doesn't support scanning. usb0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: EA:7D:EF:60:C9:0B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=70/70 Signal level=-23 dBm Encryption key:on ESSID:"ghostrider" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Ad-Hoc Extra:tsf=000000005a1ab50e Extra: Last beacon: 6242ms ago IE: Unknown: 000A67686F73747269646572 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 06020000 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: 2D1A2C181BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D16010800000000FF000000000000000000000000000000 IE: Unknown: DD09001018020000000000 Then I edited /etc/network/interfaces file to the following: root@arm:/etc/wpa_supplicant# cat /etc/network/interfaces auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # Example to keep MAC address between reboots #hwaddress ether DE:AD:BE:EF:CA:FE # WiFi Example auto wlan0 iface wlan0 inet dhcp wpa-ssid "ghostrider" wpa-psk "b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf" But I cannot still connect to the wireless network: root@arm:/etc/wpa_supplicant# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Asociated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on eth0 no wireless extensions. root@arm:/etc/network# ifup wlan0 Failed to bring up wlan0. What is wrong? Should I change any other files also? But I think it was enough. By the way if you are curious about where that wpa-psk came from: zero@ghostrider:~$ wpa_passphrase ghostrider 34bddf67c2 network={ ssid="ghostrider" #psk="34bddf67c2" psk=b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf } I will appreciate any effort to help. Regards, Amadeus ps: Also I tried to connect manually: root@arm:/etc/network# iwconfig wlan0 essid ghostrider key s:34bddf67c2 But this did not solve my problem also.

    Read the article

  • kubuntu: wireless manager can't find any networks

    - by timuçin
    I just installed Kubuntu 12.10 and as I knew my wireless driver would not be recognized, I installed it manually through here. I suppose I shall mention that I also had to do this. The driver worked just fine until I restarted my system. Since then I can't even start over. My wireless card is realtek 8723 The oly lead I have is this piece of log: 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> wpa_supplicant started 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0) supports 4 scan SSIDs 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0): supplicant interface state: starting -> ready 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0): device state change: unavailable -> disconnected (reason 'supplicant-available') [20 30 42] 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <warn> Trying to remove a non-existant call id. 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0): supplicant interface state: ready -> inactive 11/14/12 07:35:21 AM timucin-W150ER NetworkManager[989] <info> (wlan0) supports 4 scan SSIDs I feel really bad that I have been trying so many things and even while I am trying them I get a problem at every step. I am really frustrated. You can the time in the logs, I didn't get up early. Just needed to share my feelings. Even the ethernet cable I have use is short for God's sake, I have had to sit at this massively uncomfortable posture for hours. edit: I discovered something interesting. When I boot my windows I see that my wireless manager says "disconnected" now. However when I start ubuntu after windows and modprobe rtl8723e wireless works just fine. Then again, when I restart ubuntu I am back where I have started. So now I have to start windows, restart my machine and do the modprobe thing to see wireless networks.

    Read the article

  • Toshiba wireless is blocked

    - by zorrillo
    I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

    Read the article

  • Atheros wireless not working

    - by Chandru1
    I have been struggling hard since i have installed Ubuntu 10.10 but it has been difficult for me to get my wifi working. So here is what i tried. First i checked whether i have the driver using the ifconfig command and it shows the wireless lan driver as wlan0. Next, i tried the command iwlist wlan0 scanning by becoming the root which gave me the output as no scan results. Next, i visited this link https://help.ubuntu.com/community/WifiDocs/Driver/Atheros to see as to what problem my laptop may have. I do own have an ath5k chipset. And as i followed the instructions in the above link in one of the blacklist-ath_pci.conf file had this written in it. For some Atheros 5K RF MACs, the madwifi driver loads buts fails to correctly initialize the hardware, leaving it in a state from which ath5k cannot recover. To prevent this condition, stop madwifi from loading by default. Use Jockey to select one driver or the other. (Ubuntu: #315056, #323830 I am not that good at Linux but i have given it a try. I am desperate to have my wifi working and i would be glad if this community could help. ADDED: If anyone would like to know as to what drivers i am using this is the output. network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wlan0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath5k driverversion=2.6.35-24-generic firmware=N/A latency=168 link=no maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11bg resources: irq:18 memory:d0000000-d000ffff Some more information and output as to what i have done. lsmod | grep ath ath5k 130083 0 mac80211 231541 1 ath5k ath 8153 1 ath5k cfg80211 144470 3 ath5k,mac80211,ath led_class 2633 1 ath5k

    Read the article

  • How to get Broadcom BCM 43XX Wireless card working

    - by Fer1805
    NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

  • How do I install windows wireless driver for TP-Link TL-WN7200ND

    - by Jim
    I'm using the TP-Link TL-WN7200ND USB wireless adapter. I have downloaded the Windows drivers and updated Ubuntu to 10.10 by manually connecting the computer to the router. I also installed ndiswrapper-gtk. I get a Windows Wireless Drivers in my Administration menu, and I was able to get it to read the Windows 7 .inf file. The .inf for XP does not work. It adds it and the driver appears in the list with "Hardware: present". I set up the wireless connection information (ESSID and WPA2-Personal key). Problem: I don't see the network manager icon in the top right of the screen. I managed to manually start it manually using sudo services network-manager restart but it shows no connections in the menu, saying that there's nothing to manage. In my /etc/network/interfaces file I have an entry for the loopback and the standard two-liner for eth0 with dhcp. From memory, something like: iface eth0 auto eth0 dhcp I had read somewhere that 10.10 would have standard support for my wireless adapter (TL-WN7200ND) but that seems not to be the case. However, I don't ever remember having the network-manager icon in the top-right and it does not auto-start at the moment. This was originally an Ubuntu 9.10 install that I've upgraded over time. I also used to use pppoeconf to connect to the net, which might affect the /etc/network/interfaces file?

    Read the article

  • Trendnet tew-424ub wireless not working after update 12.10

    - by dwa
    I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

    Read the article

  • recent unreliable wireless connection with Netgear KWGR614 router

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

    Read the article

  • Wireless on ThinkPad Edge E420s

    - by user21820
    I have installed Kubuntu 11.04 (Natty) on my ThinkPad Edge E420 laptop. Unfortunately, the wireless is not working. I have got Windows 7 installed besides Kubuntu, and wireless is working with no problems there, so it has to be problem of the OS. What I tried: I installed the official driver from Realtek RLT8192CE. After reboot the wireless didn't work, but at least the system was able to detect that it is present in the system. However, after executing lscpi -v, under the card's details there was a line "Currently used driver" which said "r8169". Why is this? I did all of this according to a manual on http://www.php-architect.com/blog/2010/05/01/getting-wireless-to-work-on-lenovo-thinkpad-t400-with-ubuntu-10-4-lucid/. There a meany other similar ones, but don't work for me either. My questions are: 1) Is there any way to get this fixed? If yes, how to do so? 2) Do you think OpenSUSE (or any other distro) is better distribution concerning such hardware issues, so should I give it a try? If yes, which distro gives me the best chance?

    Read the article

  • ifconfig can't see USB wireless

    - by Alex
    I have a wifi USB dongle which I have previously used on a Raspberry Pi (this it is what it is target at). I am trying to get it working on an Nvidia Jetson TK1, however I am having some problems. When I run ifconfig I can't see the wifi, only the ethernet and local loopback. iwconfig reports no wireless extensions on all devices. lsusb does find the device: Bus 002 Device 008: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter So I am not sure why the network tools can't see it. I have tried logging on with a GUI and opening up the network settings through Unity, but cannot see any wireless devices either. Not sure if this is useful, but output of lsmod: Module Size Used by nvhost_vi 2940 0 How can I enable wireless networking on this computer? Command line approach is preferred, but either is fine. UPDATE I don't have the kernel module rt2800usb anywhere on my system. If I do an apt-file search for rt2800usb it lists a number of packages of the pattern: linux-image-3.13.0-*. Perhaps installing one of these will do the trick, but can anyone tell me if its safe to do so?

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >