Search Results

Search found 1856 results on 75 pages for 'kb alertz'.

Page 12/75 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• Win7 Bluescreen: IRQ_NOT_LESS_OR_EQUAL | athrxusb.sys

  - by wretrOvian

  Hi I'd left my system on last night, and found the bluescreen in the morning. This has been happening occasionally, over the past few days. Details: ================================================== Dump File : 022710-18236-01.dmp Crash Time : 2/27/2010 8:46:44 AM Bug Check String : DRIVER_IRQL_NOT_LESS_OR_EQUAL Bug Check Code : 0x000000d1 Parameter 1 : 00000000`00001001 Parameter 2 : 00000000`00000002 Parameter 3 : 00000000`00000000 Parameter 4 : fffff880`06b5c0e1 Caused By Driver : athrxusb.sys Caused By Address : athrxusb.sys+760e1 File Description : Product Name : Company : File Version : Processor : x64 Computer Name : Full Path : C:\Windows\minidump\022710-18236-01.dmp Processors Count : 2 Major Version : 15 Minor Version : 7600 ================================================== HiJackThis ("[...]" indicates removed text; full log posted to pastebin): Logfile of Trend Micro HijackThis v2.0.2 Scan saved at 8:49:15 AM, on 2/27/2010 Platform: Unknown Windows (WinNT 6.01.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16385) Boot mode: Normal Running processes: C:\Windows\DAODx.exe C:\Program Files (x86)\ASUS\EPU\EPU.exe C:\Program Files\ASUS\TurboV\TurboV.exe C:\Program Files (x86)\PowerISO\PWRISOVM.EXE C:\Program Files (x86)\OpenOffice.org 3\program\soffice.exe C:\Program Files (x86)\OpenOffice.org 3\program\soffice.bin D:\Downloads\HijackThis.exe C:\Program Files (x86)\uTorrent\uTorrent.exe R1 - HKCU\Software\Microsoft\Internet Explorer\[...] [...] O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files (x86)\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [HDAudDeck] C:\Program Files (x86)\VIA\VIAudioi\VDeck\VDeck.exe -r O4 - HKLM\..\Run: [StartCCC] "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun O4 - HKLM\..\Run: [TurboV] "C:\Program Files\ASUS\TurboV\TurboV.exe" O4 - HKLM\..\Run: [PWRISOVM.EXE] C:\Program Files (x86)\PowerISO\PWRISOVM.EXE O4 - HKLM\..\Run: [googletalk] C:\Program Files (x86)\Google\Google Talk\googletalk.exe /autostart O4 - HKLM\..\Run: [AdobeCS4ServiceManager] "C:\Program Files (x86)\Common Files\Adobe\CS4ServiceManager\CS4ServiceManager.exe" -launchedbylogin O4 - HKCU\..\Run: [uTorrent] "C:\Program Files (x86)\uTorrent\uTorrent.exe" O4 - HKUS\S-1-5-19\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-19\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'LOCAL SERVICE') O4 - HKUS\S-1-5-20\..\Run: [Sidebar] %ProgramFiles%\Windows Sidebar\Sidebar.exe /autoRun (User 'NETWORK SERVICE') O4 - HKUS\S-1-5-20\..\RunOnce: [mctadmin] C:\Windows\System32\mctadmin.exe (User 'NETWORK SERVICE') O4 - Startup: OpenOffice.org 3.1.lnk = C:\Program Files (x86)\OpenOffice.org 3\program\quickstart.exe O13 - Gopher Prefix: O23 - Service: @%SystemRoot%\system32\Alg.exe,-112 (ALG) - Unknown owner - C:\Windows\System32\alg.exe (file missing) O23 - Service: AMD External Events Utility - Unknown owner - C:\Windows\system32\atiesrxx.exe (file missing) O23 - Service: ASUS System Control Service (AsSysCtrlService) - Unknown owner - C:\Program Files (x86)\ASUS\AsSysCtrlService\1.00.02\AsSysCtrlService.exe O23 - Service: DeviceVM Meta Data Export Service (DvmMDES) - DeviceVM - C:\ASUS.SYS\config\DVMExportService.exe O23 - Service: @%SystemRoot%\system32\efssvc.dll,-100 (EFS) - Unknown owner - C:\Windows\System32\lsass.exe (file missing) O23 - Service: ESET HTTP Server (EhttpSrv) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\EHttpSrv.exe O23 - Service: ESET Service (ekrn) - ESET - C:\Program Files\ESET\ESET NOD32 Antivirus\x86\ekrn.exe O23 - Service: @%systemroot%\system32\fxsresm.dll,-118 (Fax) - Unknown owner - C:\Windows\system32\fxssvc.exe (file missing) O23 - Service: FLEXnet Licensing Service - Acresso Software Inc. - C:\Program Files (x86)\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService.exe O23 - Service: FLEXnet Licensing Service 64 - Acresso Software Inc. - C:\Program Files\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService64.exe O23 - Service: InstallDriver Table Manager (IDriverT) - Macrovision Corporation - C:\Program Files (x86)\Common Files\InstallShield\Driver\11\Intel 32\IDriverT.exe O23 - Service: @keyiso.dll,-100 (KeyIso) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @comres.dll,-2797 (MSDTC) - Unknown owner - C:\Windows\System32\msdtc.exe (file missing) O23 - Service: @%SystemRoot%\System32\netlogon.dll,-102 (Netlogon) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%systemroot%\system32\psbase.dll,-300 (ProtectedStorage) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: Protexis Licensing V2 (PSI_SVC_2) - Protexis Inc. - c:\Program Files (x86)\Common Files\Protexis\License Service\PsiService_2.exe O23 - Service: @%systemroot%\system32\Locator.exe,-2 (RpcLocator) - Unknown owner - C:\Windows\system32\locator.exe (file missing) O23 - Service: @%SystemRoot%\system32\samsrv.dll,-1 (SamSs) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\snmptrap.exe,-3 (SNMPTRAP) - Unknown owner - C:\Windows\System32\snmptrap.exe (file missing) O23 - Service: @%systemroot%\system32\spoolsv.exe,-1 (Spooler) - Unknown owner - C:\Windows\System32\spoolsv.exe (file missing) O23 - Service: @%SystemRoot%\system32\sppsvc.exe,-101 (sppsvc) - Unknown owner - C:\Windows\system32\sppsvc.exe (file missing) O23 - Service: Steam Client Service - Valve Corporation - C:\Program Files (x86)\Common Files\Steam\SteamService.exe O23 - Service: @%SystemRoot%\system32\ui0detect.exe,-101 (UI0Detect) - Unknown owner - C:\Windows\system32\UI0Detect.exe (file missing) O23 - Service: @%SystemRoot%\system32\vaultsvc.dll,-1003 (VaultSvc) - Unknown owner - C:\Windows\system32\lsass.exe (file missing) O23 - Service: @%SystemRoot%\system32\vds.exe,-100 (vds) - Unknown owner - C:\Windows\System32\vds.exe (file missing) O23 - Service: @%systemroot%\system32\vssvc.exe,-102 (VSS) - Unknown owner - C:\Windows\system32\vssvc.exe (file missing) O23 - Service: @%systemroot%\system32\wbengine.exe,-104 (wbengine) - Unknown owner - C:\Windows\system32\wbengine.exe (file missing) O23 - Service: @%Systemroot%\system32\wbem\wmiapsrv.exe,-110 (wmiApSrv) - Unknown owner - C:\Windows\system32\wbem\WmiApSrv.exe (file missing) O23 - Service: @%PROGRAMFILES%\Windows Media Player\wmpnetwk.exe,-101 (WMPNetworkSvc) - Unknown owner - C:\Program Files (x86)\Windows Media Player\wmpnetwk.exe (file missing) -- End of file - 6800 bytes CPU-Z ("[...]" indicates removed text; see full log posted to pastebin): CPU-Z TXT Report ------------------------------------------------------------------------- Binaries ------------------------------------------------------------------------- CPU-Z version 1.53.1 Processors ------------------------------------------------------------------------- Number of processors 1 Number of threads 2 APICs ------------------------------------------------------------------------- Processor 0 -- Core 0 -- Thread 0 0 -- Core 1 -- Thread 0 1 Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 2 (max 2) Number of threads 2 (max 2) Name AMD Phenom II X2 550 Codename Callisto Specification AMD Phenom(tm) II X2 550 Processor Package Socket AM3 (938) CPUID F.4.2 Extended CPUID 10.4 Brand ID 29 Core Stepping RB-C2 Technology 45 nm Core Speed 3110.7 MHz Multiplier x FSB 15.5 x 200.7 MHz HT Link speed 2006.9 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, SSE4A, x86-64, AMD-V L1 Data cache 2 x 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 2 x 64 KBytes, 2-way set associative, 64-byte line size L2 cache 2 x 512 KBytes, 16-way set associative, 64-byte line size L3 cache 6 MBytes, 48-way set associative, 64-byte line size FID/VID Control yes Min FID 4.0x P-State FID 0xF - VID 0x10 P-State FID 0x8 - VID 0x18 P-State FID 0x3 - VID 0x20 P-State FID 0x100 - VID 0x2C Package Type 0x1 Model 50 String 1 0x7 String 2 0x6 Page 0x0 TDP Limit 79 Watts TDC Limit 66 Amps Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Attached device PCI device at bus 0, device 24, function 4 Thread dumps ------------------------------------------------------------------------- CPU Thread 0 APIC ID 0 Topology Processor ID 0, Core ID 0, Thread ID 0 Type 0200400Ah Max CPUID level 00000005h Max CPUID ext. level 8000001Bh Cache descriptor Level 1, I, 64 KB, 1 thread(s) Cache descriptor Level 1, D, 64 KB, 1 thread(s) Cache descriptor Level 2, U, 512 KB, 1 thread(s) Cache descriptor Level 3, U, 6 MB, 2 thread(s) CPUID 0x00000000 0x00000005 0x68747541 0x444D4163 0x69746E65 0x00000001 0x00100F42 0x00020800 0x00802009 0x178BFBFF 0x00000002 0x00000000 0x00000000 0x00000000 0x00000000 0x00000003 0x00000000 0x00000000 0x00000000 0x00000000 0x00000004 0x00000000 0x00000000 0x00000000 0x00000000 0x00000005 0x00000040 0x00000040 0x00000003 0x00000000 [...] CPU Thread 1 APIC ID 1 Topology Processor ID 0, Core ID 1, Thread ID 0 Type 0200400Ah Max CPUID level 00000005h Max CPUID ext. level 8000001Bh Cache descriptor Level 1, I, 64 KB, 1 thread(s) Cache descriptor Level 1, D, 64 KB, 1 thread(s) Cache descriptor Level 2, U, 512 KB, 1 thread(s) Cache descriptor Level 3, U, 6 MB, 2 thread(s) CPUID 0x00000000 0x00000005 0x68747541 0x444D4163 0x69746E65 0x00000001 0x00100F42 0x01020800 0x00802009 0x178BFBFF 0x00000002 0x00000000 0x00000000 0x00000000 0x00000000 0x00000003 0x00000000 0x00000000 0x00000000 0x00000000 0x00000004 0x00000000 0x00000000 0x00000000 0x00000000 0x00000005 0x00000040 0x00000040 0x00000003 0x00000000 [...] Chipset ------------------------------------------------------------------------- Northbridge AMD 790GX rev. 00 Southbridge ATI SB750 rev. 00 Memory Type DDR3 Memory Size 4096 MBytes Channels Dual, (Unganged) Memory Frequency 669.0 MHz (3:10) CAS# latency (CL) 9.0 RAS# to CAS# delay (tRCD) 9 RAS# Precharge (tRP) 9 Cycle Time (tRAS) 24 Bank Cycle Time (tRC) 33 Command Rate (CR) 1T Uncore Frequency 2006.9 MHz Memory SPD ------------------------------------------------------------------------- DIMM # 1 SMBus address 0x50 Memory type DDR3 Module format UDIMM Manufacturer (ID) G.Skill (7F7F7F7FCD000000) Size 2048 MBytes Max bandwidth PC3-10700 (667 MHz) Part number F3-10600CL9-2GBNT Number of banks 8 Nominal Voltage 1.50 Volts EPP no XMP no JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency JEDEC #1 6.0-6-6-17-23 @ 457 MHz JEDEC #2 7.0-7-7-20-27 @ 533 MHz JEDEC #3 8.0-8-8-22-31 @ 609 MHz JEDEC #4 9.0-9-9-25-34 @ 685 MHz DIMM # 2 SMBus address 0x51 Memory type DDR3 Module format UDIMM Manufacturer (ID) G.Skill (7F7F7F7FCD000000) Size 2048 MBytes Max bandwidth PC3-10700 (667 MHz) Part number F3-10600CL9-2GBNT Number of banks 8 Nominal Voltage 1.50 Volts EPP no XMP no JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency JEDEC #1 6.0-6-6-17-23 @ 457 MHz JEDEC #2 7.0-7-7-20-27 @ 533 MHz JEDEC #3 8.0-8-8-22-31 @ 609 MHz JEDEC #4 9.0-9-9-25-34 @ 685 MHz DIMM # 1 SPD registers [...] DIMM # 2 SPD registers [...] Monitoring ------------------------------------------------------------------------- Mainboard Model M4A78T-E (0x000001F7 - 0x00A955E4) LPCIO ------------------------------------------------------------------------- LPCIO Vendor ITE LPCIO Model IT8720 LPCIO Vendor ID 0x90 LPCIO Chip ID 0x8720 LPCIO Revision ID 0x2 Config Mode I/O address 0x2E Config Mode LDN 0x4 Config Mode registers [...] Register space LPC, base address = 0x0290 Hardware Monitors ------------------------------------------------------------------------- Hardware monitor ITE IT87 Voltage 1 1.62 Volts [0x65] (VIN1) Voltage 2 1.15 Volts [0x48] (CPU VCORE) Voltage 3 5.03 Volts [0xBB] (+5V) Voltage 8 3.34 Volts [0xD1] (VBAT) Temperature 0 39°C (102°F) [0x27] (TMPIN0) Temperature 1 43°C (109°F) [0x2B] (TMPIN1) Fan 0 3096 RPM [0xDA] (FANIN0) Register space LPC, base address = 0x0290 [...] Hardware monitor AMD SB6xx/7xx Voltage 0 1.37 Volts [0x1D2] (CPU VCore) Voltage 1 3.50 Volts [0x27B] (CPU IO) Voltage 2 12.68 Volts [0x282] (+12V) Hardware monitor AMD Phenom II X2 550 Power 0 89.10 W (Processor) Temperature 0 35°C (94°F) [0x115] (Core #0) Temperature 1 35°C (94°F) [0x115] (Core #1)

  Read the article

• Perfmon - Redirector current command 0 result

  - by Dave

  I'd like to monitor how many SMB connections there are at any given time for my 2008R2 file server, but when I add Redirector/Current Commands in perfmon, I get 0 results. This KB from Microsoft isn't exactly helpful either: http://support.microsoft.com/kb/2523382 It mearly confirms there is an issue, but doesn't provide a work around. How would I go about getting the current number of SMB connections? Thanks for your help in advance.

  Read the article

• Queston about torrents

  - by c0mrade

  Why do my torrents go at rate 25/30 kb/s and my regular http downloads rate up to 300 kb/s .. is my ISP to blame for this, I meant torrents have like thousand seeders and again its very slow.How are they blocking torrent speed, can I bypass it?

  Read the article

• AAC Sample Rate and Bit Rate for High Quality Audio?

  - by marco.ragogna

  What are the AAC Sample Rate and Bit Rate settings to set in order to encode an audio track with a quality comparable to MP3 320kbps? I need to backup a DVD movie, the default settings for AAC are Bitrate (KB/s) 128 Sample Rate (HZ) 44100 should I set Bitrate (KB/s) 320 Sample Rate (HZ) 48000 or the default are already good?

  Read the article

• How to disable SSL 2.0 on IIS 7.5?

  - by John Hoge

  I've seen this KB Article which Microsoft put out covering how to remove SSL 2.0 on IIS 7.0 and earlier, but I can't find anything advising on how to do the same on IIS 7.5. The registry keys mentioned on that KB article are no longer in the registry.

  Read the article

• MSDTC failed in windows cluster any idea???

  - by Cute

  Hi I have created a windows2003 cluster and then try to configure MSDTC by following the link http://support.microsoft.com/kb/301600/#appliesto after follow this i have enable network DTC access in Windows Server 2003 by following http://support.microsoft.com/kb/817064/ But the group i have created MSDTC( as said in first link from 7th point onwards ) for the resourse Distribution Transaction Coordinator failed and all are in online after done this. But i dont know why it is failing.. I dont know how to post the screen shot here.....

  Read the article

• MSDTC failed in windows cluster any idea?

  - by Cute

  I have created a windows2003 cluster and then try to configure MSDTC by following the link http://support.microsoft.com/kb/301600/#appliesto after follow this i have enable network DTC access in Windows Server 2003 by following http://support.microsoft.com/kb/817064/ But the group i have created MSDTC( as said in first link from 7th point onwards ) for the resourse Distribution Transaction Coordinator failed and all are in online after done this. But i dont know why it is failing.. I dont know how to post the screen shot here.....

  Read the article

• can router configuration cause decreasing of download rate?

  - by behrooz

  My download speed got crazy since I changed the router's IP. But nothing got fixed after doing a factory reset. The speed was 1024 kb/s (128 kB/s) but it is 200kb/s (max) right now. I mean it works good if a request is small (i.e. a HTTP request) but it gets slow if a request has a big response. Help me please. (It is three days I'm downloading VS2010.)

  Read the article

• How to get higher download rate than upload rate

  - by user23950

  i'm using bandwidthplace.com to measure my internet speed. And here it is: Download Speed: 422 kbps (52.8 KB/sec transfer rate) Upload Speed: 202 kbps (25.3 KB/sec transfer rate) Can you please explain to me how did they get the 52.8 transfer rate. And how do I get to lower the upload speed in order for me to get higher download speed.

  Read the article

• How do I optimize TCP stack for HTTP server?

  - by jcisio

  I have a HTTP server that serves only two kinds of page: about 10 KB and about 16 KB (both compressed, other files are from CDN). As the latency is quite high (ping takes more than 300 ms), I want to optimize the TCP stack so that client receives the whole page ASAP. Thus, I have a double question: Which parameter do I have to change (which value of TCP window)? How to change in (a Debian box, and FYI, there is a Varnish before the HTTP server).

  Read the article

• Use DivX settings to encode to mp4 with ffmpeg

  - by sjngm

  I'm used to use VirtualDub to encode a video to AVI container with DivX-codec (and MP3 for audio). Now I'm planning to use ffmpeg to encode videos to MP4 container with h264-codec. What I've figured out is that I need to use libx264 and one of those presets to make anything work. However, I'm amazed about the video bitrate ffmpeg uses for encoding. What I currently have is this little batch file: @ECHO OFF SETLOCAL SET IN=source.avs SET FFMPEG_PATH=C:\Program Files (x86)\ffmpeg SET PRESET=-fpre "%FFMPEG_PATH%\presets\libx264-lossless_slow.ffpreset" SET AUDIO=-acodec libmp3lame -ab 128000 SET VIDEO=-vcodec libx264 -vb 1978000 "%FFMPEG_PATH%\ffmpeg.exe" -i %IN% %AUDIO% %VIDEO% %PRESET% test.mp4 ENDLOCAL With this I tell ffmpeg to use 1978k as the bitrate, but ffmpeg uses 15000k+! I tried other presets, but they don't use my specified bitrate. Here are the presets I have: libx264-baseline.ffpreset libx264-ipod320.ffpreset libx264-ipod640.ffpreset libx264-lossless_fast.ffpreset libx264-lossless_max.ffpreset libx264-lossless_medium.ffpreset libx264-lossless_slow.ffpreset libx264-lossless_slower.ffpreset libx264-lossless_ultrafast.ffpreset ffmpeg version: FFmpeg git-N-29181-ga304071 libavutil 50. 40. 1 / 50. 40. 1 libavcodec 52.120. 0 / 52.120. 0 libavformat 52.108. 0 / 52.108. 0 libavdevice 52. 4. 0 / 52. 4. 0 libavfilter 1. 79. 0 / 1. 79. 0 libswscale 0. 13. 0 / 0. 13. 0 Note that I don't use the latest version as it has problems with spaces in filenames. Here's what seems to be the full parameter list DivX 6.9.2 uses: -bvnn 1978000 -vbv 218691200,100663296,100663296 -dir "C:\Users\sjngm\AppData\Roaming\DivX\DivX Codec" -w -b 1 -use_presets=1 -preset=10 -windowed_fullsearch=2 -thread_delay=1 What command line parameters would that be for ffmpeg? EDIT: Going with slhck's suggestion I tried a new 32-bit version. I have no idea if that is 0.9 or newer, I can't find that info. ffmpeg version N-36890-g67f5650 libavutil 51. 34.100 / 51. 34.100 libavcodec 53. 56.105 / 53. 56.105 libavformat 53. 30.100 / 53. 30.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 59.100 / 2. 59.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 6.100 / 0. 6.100 libpostproc 51. 2.100 / 51. 2.100 I reworked my batch file to look like this (interestingly enough I can't find parameter -vprofile in the documentation): @ECHO OFF SETLOCAL SET IN=VTS_01_1.avs SET FFMPEG_PATH=C:\Program Files (x86)\ffmpeg SET PRESET=-vprofile high -preset veryslow SET AUDIO=-acodec libmp3lame -ab 128000 SET VIDEO=-vcodec libx264 -vb 1978000 "%FFMPEG_PATH%\ffmpeg.exe" -i %IN% %AUDIO% %PRESET% %VIDEO% test.mp4 ENDLOCAL I see that it now uses the bitrate properly (thanks to LongNeckbeard for pointing out that the lossless-stuff ignores the bitrate!). Just in case you wonder how I came up with the 1978000, I'm using this formula which I found valid for DivX-files (I'm guessing the bitrate won't change that much for h264): width * height * 25 * 0.22 / 1000 I'm not sure if the 0.22 correlates with the CRF somehow. Overall I forgot to say the I will use a two-pass scenario, which is why I don't use the CRF here. I will try to read more about this. Currently I'm just trying to get something running that shows me that I'm doing something right (ffmpeg isn't the easiest tool to understand ;)). C:\Program Files (x86)\ffmpeg\ffmpeg.exe" -i VTS_01_1.avs -acodec libmp3lame -ab 128000 -vcodec libx264 -vb 1978000 -vprofile high -preset veryslow test.mp4 The output is now: ffmpeg version N-36890-g67f5650 Copyright (c) 2000-2012 the FFmpeg developers built on Jan 16 2012 21:57:13 with gcc 4.6.2 configuration: --enable-gpl --enable-version3 --disable-w32threads --enable-runtime-cpudetect --enable-avisynth --enable-bzlib --enable-frei0r --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-libfreetype --enable-libgsm --enable-libmp3lame --enable-libopenjpeg --enable-librtmp --enable-libschroedinger --enable-libspeex --enable-libtheora --enable-libvo-aacenc --enable-libvo-amrwbenc --enable-libvorbis --enable-libvpx --enable-libx264 --enable-libxavs --enable-libxvid --enable-zlib libavutil 51. 34.100 / 51. 34.100 libavcodec 53. 56.105 / 53. 56.105 libavformat 53. 30.100 / 53. 30.100 libavdevice 53. 4.100 / 53. 4.100 libavfilter 2. 59.100 / 2. 59.100 libswscale 2. 1.100 / 2. 1.100 libswresample 0. 6.100 / 0. 6.100 libpostproc 51. 2.100 / 51. 2.100 Input #0, avs, from 'VTS_01_1.avs': Duration: 00:58:46.12, start: 0.000000, bitrate: 0 kb/s Stream #0:0: Video: rawvideo (YV12 / 0x32315659), yuv420p, 576x448, 77414 kb/s, 25 tbr, 25 tbn, 25 tbc Stream #0:1: Audio: pcm_s16le ([1][0][0][0] / 0x0001), 48000 Hz, 2 channels, s16, 1536 kb/s File 'test.mp4' already exists. Overwrite ? [y/N] y w:576 h:448 pixfmt:yuv420p tb:1/1000000 sar:0/1 sws_param: [libx264 @ 05A2C400] using cpu capabilities: MMX2 SSE2Fast FastShuffle SSEMisalign LZCNT [libx264 @ 05A2C400] profile High, level 3.1 [libx264 @ 05A2C400] 264 - core 120 r2120 0c7dab9 - H.264/MPEG-4 AVC codec - Copyleft 2003-2011 - http://www.videolan.org/x264.html - options: cabac=1 ref=16 deblock=1:0:0 analyse=0x3:0x133 me=umh subme=10 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=24 chroma_me=1 trellis=2 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=3 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=8 b_pyramid=2 b_adapt=2 b_bias=0 direct=3 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=60 rc=abr mbtree=1 bitrate=1978 ratetol=1.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'test.mp4': Metadata: encoder : Lavf53.30.100 Stream #0:0: Video: h264 (![0][0][0] / 0x0021), yuv420p, 576x448, q=-1--1, 1978 kb/s, 25 tbn, 25 tbc Stream #0:1: Audio: mp3 (i[0][0][0] / 0x0069), 48000 Hz, 2 channels, s16, 128 kb/s Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Stream #0:1 -> #0:1 (pcm_s16le -> libmp3lame) Press [q] to stop, [?] for help frame= 0 fps= 0 q=0.0 size= 0kB time=00:00:00.00 bitrate= 0.0kbits/s frame= 0 fps= 0 q=0.0 size= 0kB time=00:00:00.00 bitrate= 0.0kbits/s frame= 0 fps= 0 q=0.0 size= 0kB time=00:00:00.00 bitrate= 0.0kbits/s frame= 3 fps= 1 q=22.0 size= 39kB time=00:00:00.04 bitrate=8063.8kbits/ frame= 8 fps= 2 q=22.0 size= 82kB time=00:00:00.24 bitrate=2801.3kbits/ frame= 13 fps= 3 q=23.0 size= 120kB time=00:00:00.44 bitrate=2229.5kbits/ frame= 16 fps= 4 q=23.0 size= 147kB time=00:00:00.56 bitrate=2156.7kbits/ frame= 20 fps= 4 q=22.0 size= 175kB time=00:00:00.72 bitrate=1987.4kbits/ : video:4387kB audio:273kB global headers:0kB muxing overhead 0.260038% [libx264 @ 05A2C400] frame I:2 Avg QP:19.53 size: 29850 [libx264 @ 05A2C400] frame P:76 Avg QP:22.24 size: 19541 [libx264 @ 05A2C400] frame B:359 Avg QP:25.93 size: 8210 [libx264 @ 05A2C400] consecutive B-frames: 0.5% 0.5% 0.0% 8.2% 17.2% 52.2% 16.0% 5.5% 0.0% [libx264 @ 05A2C400] mb I I16..4: 5.4% 75.3% 19.3% [libx264 @ 05A2C400] mb P I16..4: 1.3% 16.5% 2.2% P16..4: 36.3% 28.6% 12.7% 1.8% 0.2% skip: 0.4% [libx264 @ 05A2C400] mb B I16..4: 0.4% 3.8% 0.3% B16..8: 40.0% 18.4% 4.7% direct:18.5% skip:13.9% L0:45.4% L1:38.1% BI:16.5% [libx264 @ 05A2C400] final ratefactor: 20.35 [libx264 @ 05A2C400] 8x8 transform intra:83.1% inter:68.5% [libx264 @ 05A2C400] direct mvs spatial:99.2% temporal:0.8% [libx264 @ 05A2C400] coded y,uvDC,uvAC intra: 64.9% 83.4% 49.2% inter: 49.0% 50.4% 4.4% [libx264 @ 05A2C400] i16 v,h,dc,p: 25% 22% 27% 26% [libx264 @ 05A2C400] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 10% 7% 23% 9% 10% 10% 10%10% 13% [libx264 @ 05A2C400] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 11% 13% 9% 12% 11% 10% 9% 12% [libx264 @ 05A2C400] i8c dc,h,v,p: 42% 28% 16% 14% [libx264 @ 05A2C400] Weighted P-Frames: Y:18.4% UV:7.9% [libx264 @ 05A2C400] ref P L0: 29.1% 11.3% 15.7% 7.3% 6.9% 4.9% 5.1% 3.4%3.9% 2.7% 2.8% 1.8% 1.7% 1.2% 1.4% 0.9% [libx264 @ 05A2C400] ref B L0: 68.8% 11.4% 5.5% 2.9% 2.3% 1.9% 1.5% 1.1%1.1% 1.0% 0.9% 0.7% 0.5% 0.3% 0.1% [libx264 @ 05A2C400] ref B L1: 91.9% 8.1% [libx264 @ 05A2C400] kb/s:2055.88 As far as I'm concerned it doesn't look that bad to me.

  Read the article

• How can I force all internet traffic over a PPTP VPN but still allow local lan access?

  - by user126715

  I have a server running Linux Mint 12 that I want to keep connected to a PPTP VPN all the time. The VPN server is pretty reliable, but it drops on occasion so I just want to make it so all internet activity is disabled if the VPN connection is broken. I'd also like to figure out a way to restart it automatically, but that's not as big of an issue since this happens pretty rarely. I also want to always be able to connect to the box from my lan, regardless of whether the VPN is up or not. Here's what my ifconfig looks like with the VPN connected properly: eth0 Link encap:Ethernet HWaddr 00:22:15:21:59:9a inet addr:192.168.0.171 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:15ff:fe21:599a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37389 errors:0 dropped:0 overruns:0 frame:0 TX packets:29028 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:37781384 (37.7 MB) TX bytes:19281394 (19.2 MB) Interrupt:41 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1446 errors:0 dropped:0 overruns:0 frame:0 TX packets:1446 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:472178 (472.1 KB) TX bytes:472178 (472.1 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.10.11.10 P-t-P:10.10.11.9 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:23 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1368 (1.3 KB) TX bytes:1812 (1.8 KB) Here's an iptables script I found elsewhere that seemed to be for the problem I'm trying to solve, but it wound up blocking all access, but I'm not sure what I need to change: #!/bin/bash #Set variables IPT=/sbin/iptables VPN=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 10.` LAN=192.168.0.0/24 #Flush rules $IPT -F $IPT -X #Default policies and define chains $IPT -P OUTPUT DROP $IPT -P INPUT DROP $IPT -P FORWARD DROP #Allow input from LAN and tun0 ONLY $IPT -A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT $IPT -A INPUT -i lo -j ACCEPT $IPT -A INPUT -i tun0 -m conntrack --ctstate NEW -j ACCEPT $IPT -A INPUT -s $LAN -m conntrack --ctstate NEW -j ACCEPT $IPT -A INPUT -j DROP #Allow output from lo and tun0 ONLY $IPT -A OUTPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT $IPT -A OUTPUT -o lo -j ACCEPT $IPT -A OUTPUT -o tun0 -m conntrack --ctstate NEW -j ACCEPT $IPT -A OUTPUT -d $VPN -m conntrack --ctstate NEW -j ACCEPT $IPT -A OUTPUT -j DROP exit 0 Thanks for your help.

  Read the article

• Concatenation of a 2 second silence audio with a normal audio not working

  - by user1665130

  I have a code for concatenation of files using ffmpeg.Here silence.wav is a mute audio file with 2 seconds length. I need to prepend this mut audio file to REC00096_Jun-06-2014 16.47.28.wav. I tried the folowing code. ffmpeg -i D:\vishnu\silence.wav -i D:\vishnu\REC00096_Jun-06-2014 16.47.28.wav \-filter_complex '[0:0][1:0][2:0][3:0]concat=n=2:v=0:a=1[out]' \-map '[out]' output.wav Following is the error i am getting. D:\vishnu>ffmpeg -i silence.wav -i "D:\vishnu\REC00096_Jun-06-2014 16.47.28.wav" -filter_complex '[0:0][1:0][2:0][3:0]concat=n=2:v=0:a=1[out]' -map '[out]' outp ut.wav ffmpeg version N-59036-g5d8e4f6 Copyright (c) 2000-2013 the FFmpeg developers built on Dec 12 2013 22:01:01 with gcc 4.8.2 (GCC) configuration: --enable-gpl --enable-version3 --disable-w32threads --enable-av isynth --enable-bzlib --enable-fontconfig --enable-frei0r --enable-gnutls --enab le-iconv --enable-libass --enable-libbluray --enable-libcaca --enable-libfreetyp e --enable-libgsm --enable-libilbc --enable-libmodplug --enable-libmp3lame --ena ble-libopencore-amrnb --enable-libopencore-amrwb --enable-libopenjpeg --enable-l ibopus --enable-librtmp --enable-libschroedinger --enable-libsoxr --enable-libsp eex --enable-libtheora --enable-libtwolame --enable-libvidstab --enable-libvo-aa cenc --enable-libvo-amrwbenc --enable-libvorbis --enable-libvpx --enable-libwavp ack --enable-libx264 --enable-libxavs --enable-libxvid --enable-zlib libavutil 52. 58.100 / 52. 58.100 libavcodec 55. 45.101 / 55. 45.101 libavformat 55. 22.100 / 55. 22.100 libavdevice 55. 5.102 / 55. 5.102 libavfilter 3. 92.100 / 3. 92.100 libswscale 2. 5.101 / 2. 5.101 libswresample 0. 17.104 / 0. 17.104 libpostproc 52. 3.100 / 52. 3.100 Input #0, wav, from 'silence.wav': Metadata: encoder : Lavf55.22.100 Duration: 00:00:02.02, bitrate: 4234 kb/s Stream #0:0: Audio: pcm_s16le ([1][0][0][0] / 0x0001), 44100 Hz, 5.1, s16, 4 233 kb/s Guessed Channel Layout for Input Stream #1.0 : mono Input #1, wav, from 'D:\vishnu\REC00096_Jun-06-2014 16.47.28.wav': Duration: 00:00:08.04, bitrate: 384 kb/s Stream #1:0: Audio: pcm_s16le ([1][0][0][0] / 0x0001), 24000 Hz, mono, s16, 384 kb/s [wav @ 036f5e40] Invalid stream specifier: '[out]'. Last message repeated 1 times Stream map ''[out]'' matches no streams. D:\vishnu>

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files

  - by yegor

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• What could cause a program to stay in "Add/Remove Programs" even after removing from registry

  - by Ryan

  Trying to manually remove an entry from Control Panel Add/Remove Programs. (custom software, not MS KB patch or windows component and not doing anyting 'funky' like trying to stop itself form being uninstalled) Followed http://support.microsoft.com/kb/314481 removing all applicable registry keys for program from HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\ and even tried rebooting but still it persists. Double checked followed KB314481 and search for program name doesn't return any other matches in that part of the registry. Any ideas what would cause this or how to solve?

  Read the article

• Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

  - by Adam

  I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

  Read the article

• Network Interface Lost Functionality after Firewall Installation Hung

  - by Sadeq Dousti

  I tried to install Agnitum Outpost firewall, but the setup hung while installing network drivers. Oddly, the NIC properties shows no connect string whatsoever, nor any services: http://pic-ups.com/images/1fjf.png Device Manager shows problematic drivers as well: www.pic-ups.com/images/2aqa.png Any suggestions? PS: I'm using Windows XP SP3. PS2: I applied instructions below, but all were in vein: www.agnitum.com/support/kb/article.php?id=1000041 www.agnitum.com/support/kb/article.php?id=1000159

  Read the article

• How do you splice out a part of an xvid encoded avi file, with ffmpeg? (no problems with other files)

  - by user11955

  Im using the following command, which works for most files, except what seems to be xvid encoded ones /usr/bin/ffmpeg -sameq -i file.avi -ss 00:01:00 -t 00:00:30 -ac 2 -r 25 -copyts output.avi So this should basically splice out 30 seconds of video + audio, starting from 1 minute mark. It does START encoding at the 00:01:00 mark but it goes all the way to the end of the file for some reason, ignoring that I want just 30 seconds. The output looks like this. FFmpeg version git-ecc4bdd, Copyright (c) 2000-2010 the FFmpeg developers built on May 31 2010 04:52:24 with gcc 4.4.3 20100127 (Red Hat 4.4.3-4) configuration: --enable-libx264 --enable-libxvid --enable-libmp3lame --enable-libopenjpeg --enable-libfaac --enable-libvorbis --enable-gpl --enable-nonfree --enable-libxvid --enable-pthreads --enable-libfaad --extra-cflags=-fPIC --enable-postproc --enable-libtheora --enable-libvorbis --enable-shared libavutil 50.15. 2 / 50.15. 2 libavcodec 52.67. 0 / 52.67. 0 libavformat 52.62. 0 / 52.62. 0 libavdevice 52. 2. 0 / 52. 2. 0 libavfilter 1.20. 0 / 1.20. 0 libswscale 0.10. 0 / 0.10. 0 libpostproc 51. 2. 0 / 51. 2. 0 [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected Input #0, avi, from 'file.avi': Metadata: ISFT : VirtualDubMod 1.5.10.2 (build 2540/release) Duration: 00:02:00.00, start: 0.000000, bitrate: 1587 kb/s Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], 25 tbr, 25 tbn, 25 tbc Stream #0.1: Audio: ac3, 48000 Hz, 5.1, s16, 448 kb/s File 'lol6.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to 'lol6.avi': Metadata: ISFT : Lavf52.62.0 Stream #0.0: Video: mpeg4, yuv420p, 672x368 [PAR 1:1 DAR 42:23], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, 2 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [mpeg4 @ 0x17cf770]Invalid and inefficient vfw-avi packed B frames detected [buffer @ 0x184b610]Buffering several frames is not supported. Please consume all available frames before adding a new one. frame= 1501 fps=104 q=0.0 Lsize= 15612kB time=30.02 bitrate=4259.7kbits/s ts/s video:15303kB audio:235kB global headers:0kB muxing overhead 0.482620% if I convert this file to mp4 for example, and then perform the same action, it works perfectly.

  Read the article

• File types and locations (if any) to exclude from AntiVirus scanning?

  - by CAD bloke

  Should I add any file types to my anti-virus's file type exclusion list? If so, which types? Should I add any locations (specifically for Windows 7) to an exclusion list? If so, which locations? Google found me a few references like http://support.microsoft.com/kb/822158 http://support.microsoft.com/kb/943556 and some site purporting to conduct expert sex changes but haven't found anything particularly confidence-inspiring.

  Read the article

• Problem install phpmyadmin on amazon ec2?

  - by yoko

  I googled on how to install phpmyadmin on ec2, and i got this syntax: sudo yum install phpmyadmin But i keep getting this: Loaded plugins: fastestmirror, priorities, security Loading mirror speeds from cached hostfile amzn-main | 2.1 kB 00:00 amzn-updates | 2.1 kB 00:00 Setting up Install Process No package phpmyadmin available. Error: Nothing to do I tried to go my website, its not installed. Please help EDIT: My Server OS: Amazon Linux AMI 64 bit I tried: yum install phpmyadmin --enablerepo=development, but still I got this error: Loaded plugins: fastestmirror, priorities, security Error getting repository data for development, repository not found

  Read the article

• Memory issue regarding UIImageView on IPhone 4.0 / IPad

  - by Sagar Mane

  Hello All, My Application is crashing due to low memory [ Received memory warning level 1 + 2] To trace this I have used Instrument and come with following points Test Enviorment : Single view controller added on Window When I don't use UIImageView Real Memory is used 3.66 MB When I uses UIImageView with Image having size 25 KB : Real Memory is used 4.24 MB. almost 560 KB extra when compare to w/o UIImageView and which keep on adding as I am adding more UIImageview on the view. below is sample code for adding UIImageview which I am refering UIImageView* iSplashImage = [[UIImageView alloc] initWithImage:[UIImage imageNamed:@"Default-Landscape.png"]]; iSplashImage.frame = CGRectMake(0, 0, 320, 480); [self.window addSubview:iSplashImage]; AND dealloc if(iSplashImage) { [iSplashImage release]; iSplashImage = nil; } Issue is this 560 KB is not getting release and after some time application receives low memory warning. Can anyone point out if I am missing something or doing else. As My application uses lots of Images in One session. Thanks in Advance, Sagar

  Read the article

• VC7.1 C1204 internal compiler error

  - by Nathan Ernst

  I'm working on modifying Firaxis' Civilization 4 core game DLL. The host application is built using VC7, hence the constraint (source not provided for the host EXE). I've been working on rewriting a large chunk of the code (focusing on low-hanging performance issues & memory leaks). I recently ran into an internal compiler error when trying to mod the code to use an array class instead of dynamically allocated 2-d arrays, I was going to use matrices from the boost lib (Civ4 is already using boost, so why not?). Basically, the issue comes down to: if I include "boost/numeric/ublas/matrix.hpp", I run into an internal compiler error C1204. MSDN has this to say: MSDN C1204 KB has this to say: KB 883655 So, I'm curious, is it possible to solve this error without a KB/SP being applied and dramatically reducing the complexity of the code? Additionally, as VC7 is no longer "supported", does anyone have a valid (supported) link for a VC7 service pack?

  Read the article

• Real average filesize in a set of files...

  - by JD

  Hi, I have an apparently "simple" problem but I can't find the solution for some reason... I have n millions files of different sizes and I want to find the average filesize. To simplify it, I grouped them in multiples of 16KB. < 16 KB = 18689546 files < 32 KB = 1365713 files < 48 KB = 1168186 files ... Of course, the simple (total_size / number of files) does not work. It gives an average of 291KB... What would be the algorithm to calculate the real average...? Thx, JD

  Read the article

• How to use Scanner to accept only valid int as input

  - by John

  I'm trying to make a small program more robust and I need some help with that. Scanner kb = new Scanner(System.in); int num1; int num2 = 0; System.out.print("Enter number 1: "); num1 = kb.nextInt(); while(num2<num1) { System.out.print("Enter number 2: "); num2 = kb.nextInt(); } Number 2 has to be greater than number 1 Also I want the program to automatically check and ignore if the user enters a character instead of a number. Because right now when a user enters for example r instead of a number the program just exits.

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >