Search Results

Search found 1007 results on 41 pages for 'kevin c'.

Page 12/41 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • Trouble with wireless driver on a Dell Latitude D830

    - by Kevin
    After uninstalling Dell's wireless utility I get a new hardware found dialog that can not find any driver for my wifi card on it's own. I'm running Windows XP Professional Service Pack 3, and I would like to use the default wifi handler since dell's utility does not work with my company's wireless switch. I did try downloading the recommend driver from the dell support site Network Adapter 2 Model Intel(R) PRO/Wireless 3945ABG Network Connection Description [12] Intel(R) PRO/Wireless 3945ABG Network Connection Status Connected

    Read the article

  • One Comcast Business Gateway, One Router, Two Web Servers

    - by Kevin Scheidt
    I have a Comcast business account with a router and a web server (info) attached. behind the router there are multiple computers and a second web server (info) which also serves as a file server. (info) has two nics in it. One direct to comcast and one connected to the router. It needs to serve the world it's websites. It needs however, to also be able to see all the internal computers and (com)'s served files. With just 1 nic (the one connected to the router, not comcast), (info) works fine but no one outside can see it. (com) services port 80 and (info) needs to handle port 80 as well. I have two domain names registered, and 5 static ip's from comcast. right now h t t p: / /www.graceamazing.com handled by (com) works fine and h t t p: / /www.graceamazing.com:1307 handled by (info) works fine. but as soon as I enable the 2nd nic in (info) h t t p: / /www.graceamazing.info runs extremely slow (Horribly slow). however, h t t p: / /www.graceamazing.com:1307 and .com work fine. (com) has an ip address via the router 70.89.233.41 (info) has a ip addy of 70.89.233.46 via comcast (2nd nic) and a internal ip of 192.168.x.100 via static behind the router. Any suggestions or changes to make that will make h t t p: / /www.graceamazing.info perform with the same speed it has when going through h t t p: / /graceamazing.com:1307 is there a setting I should check / could have misssed?

    Read the article

  • Best dual band A/B/G/N wireless router/ap for Linux

    - by Kevin Bowling
    Hello, I am looking for the best A/B/G/N dual band (simultaneous) router or access point that can be flashed with community firmware like dd-wrt or openwrt. In the past I have used the WRT54G series from Linksys with great success as access points and bridges. The WRT610N looks nice but I'm not sure how well the community firmwares support it. I am open to any manufacturer and any input or experience would be appreciated.

    Read the article

  • What are the best browser based administration tools for Linux?

    - by Kevin Kuphal
    Looking for recommendations the best comprehensive browser based administration tool for administering a Linux machine. Ideally this would be distribution agnostic. This could also be an "appliance" type product that would administer multiple machines on network. This is marked community wiki. Give your answer preferably one product per answer and vote up packages that you recommend also.

    Read the article

  • Unable to restart MySQL server on CENTOS 6.5 x86_64 kvm – server (WHM/cPanel)

    - by Kevin S
    I am not able to restart MySQL server on CENTOS 6.5 x86_64 kvm – server (WHM/cPanel). I am getting following error while trying to restart the MySQL server. Waiting for mysql to restart...............finished. mysqld_safe (/bin/sh /usr/bin/mysqld_safe --datadir=/var/lib/mysql --pid-file=/var/lib/mysql/server.domain.net.pid) running as root with PID 4227 (process table check method) mysqld (/usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --log-error=/var/lib/mysql/server.domain.net.err --open-files-limit=4096 --pid-file=/var/lib/mysql/server.domain.net.pid) running as mysql with PID 4349 (pidfile check method) mysql has failed, please contact the sysadmin (result was "mysql is not running"). I even restarted the server and tried again but same issue.

    Read the article

  • Users not getting ip when connected through wifi,but wired connection getting ip in ddwrt router

    - by Kevin Parker
    I am having DD-WRT v24-sp2(05/08/11) running on Asus RT n 13 u B1 router,with dhcp on. But users not able to connect through wifi...its showing obtaining ip address and disconnects there after. Wired Devices are getting ip address and able to access internet.Wifi was working till yesterday,but all of a sudden it stopped working. on the ddwrt controlpanelsystem information under Wireless Clients mac address of clients that are trying to connect are appearing but soon it disappears. but no such issue with wired clients. Can any one please help me in fixing this..

    Read the article

  • Time Machine for Windows

    - by Kevin L.
    A simple Google search for "Time Machine for Windows" results in a flurry of different little apps. But instead of relying on forum anecdotes and advertisements, I call on the much wiser Super User beta community for some depth on this one. Having Time Machine running on Leopard is like a warm, fuzzy blanket of comfort that I never got with RAID, rsync, or SyncToy on Windows. I'm not asking the community what the "best" backup software for Windows is, but instead: Is there any true Time Machine clone for Windows, one that includes as many of the following as possible: Completely transparent, "set-it-and-forget-it" backup Incremental backups (changes only) for every hour for a day, every day for a month, and every week until the backup disk is full Ability to rebuild from this backup disk in case of main drive meltdown (the backup doesn't have to be bootable; neither are Time Machine disks) Extremely easy to use UI (target user == wife). Bonus points for a beautiful UI

    Read the article

  • Trouble getting SSL to work with django + nginx + wsgi

    - by Kevin
    I've followed a couple of examples for Django + nginx + wsgi + ssl, but I can't get them to work. I simply get an error in my browser than I can't connect. I'm running two websites off the host. The config files are identical except for the ip addresses, server names, and directories. When neither use SSL, they work fine. When I try to listen on 443 with one of them, I can't connect to either. My config files are below, and any suggestions would be appreciated. server{ listen xxx.xxx.xxx.xxx:80; server_name sub.domain.com; access_log /home/django/logs/nginx_customerdb_http_access.log; error_log /home/django/logs/nginx_customerdb_http_error.log; location / { proxy_pass http://127.0.0.1:8080; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } location /site_media/ { alias /home/django/customerdb_site_media/; } location /admin-media/ { alias /home/django/django_admin_media/; } } server{ listen xxx.xxx.xxx.xxx:443; server_name sub.domain.com; access_log /home/django/logs/nginx_customerdb_http_access.log; error_log /home/django/logs/nginx_customerdb_http_error.log; ssl on; ssl_certificate sub.domain.com.crt; ssl_certificate_key sub.domain.com.key; ssl_prefer_server_ciphers on; location / { proxy_pass http://127.0.0.1:8080; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Protocol https; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } location /site_media/ { alias /home/django/customerdb_site_media/; } location /admin-media/ { alias /home/django/django_admin_media/; } } <VirtualHost *:8080> ServerName xxx.xxx.xxx.xxx ServerAlias xxx.xxx.xxx.xxx LogLevel warn ErrorLog /home/django/logs/apache_customerdb_error.log CustomLog /home/django/logs/apache_customerdb_access.log combined WSGIScriptAlias / /home/django/customerdb/apache/django.wsgi WSGIDaemonProcess customerdb_wsgi processes=4 threads=5 WSGIProcessGroup customerdb_wsgi SetEnvIf X-Forwarded-Protocol "^https$" HTTPS=on </VirtualHost> UDPATE: the existence of two sites (on separate IPs) on the host is the issue. if i delete the other site, the setting above mostly work. doing so also brings up another issue: chrome doesn't accept the site as secure saying that some content is not encrypted.

    Read the article

  • Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

    - by Kevin
    I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

    Read the article

  • Keyboard problem, my Insert key is mix with my Delete key. How to disable overwrite text mode?

    - by Kevin Lee
    I have a problem, everytime i type a text, it is overwriting what i have typed. i assume that the mode is set to overwriting, I want to insert the text not overwrite it, but i can't disable it because my insert key is mix up with my delete key so everytime i enter insert to disable the overwrite mode, it just delete what i type. so how to disable this? it's getting very annoying.. i'm using centOS.. and it seems that my problem is only related to netbeans because when i type here, it is set to insert mode.. but in netbeans, it just overwrites the codes! help!

    Read the article

  • Blue screen of death when moving files

    - by kevin
    i just bought a new hp amd II athlon quad core and everytime i try to move file off my desktop to a hard drive or off my hard drive to my desktop of atleast a 1g or more my computer restarts itself and gives me the blue screen of death can someone please tell me why

    Read the article

  • Change OpenVZ route to pass through ip failover

    - by Kevin Campion
    I have one dedicaced server with its own IP and another IP (failover) who refer to the first. I will wish to change the gateway of a Proxmox virtual machine (openvz) who runs on this dedicaced server to go through the failover IP rather than the ip of host main server. Once connected to a virtual machine, when I do a traceroute VE# traceroute www.google.fr traceroute to www.google.fr (209.85.229.104), 30 hops max, 60 byte packets 1 MY_SERVER_NAME.ovh.net (xxx.xxx.xxx.xxx FIRST_IP_MAIN_SERVER) 0.021 ms 0.010 ms 0.009 ms The first line tells me the ip of host main server. I would like that the traceroute display the second IP failover. VE# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 * 255.255.255.255 UH 0 0 0 venet0 default 192.0.2.1 0.0.0.0 UG 0 0 0 venet0 With iptables HOST# iptables -t nat -L Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- anywhere anywhere MASQUERADE all -- anywhere anywhere SNAT tcp -- anywhere 10.10.101.2 tcp dpt:www state NEW,RELATED,ESTABLISHED,UNTRACKED to:SECOND_IP_FAILOVER SNAT all -- 10.10.101.2 anywhere to:SECOND_IP_FAILOVER 10.10.101.2 is the virtual machine IP (interface venet0) Any ideas ?

    Read the article

  • Openstack keystone issue

    - by kevin
    i am having an issue with keystone,keystone is configured with users nova,glance and admin user and their endpoints are also defined. when performing keystone token-get it is showing token,but for commands like keystone user-list its showing No handlers could be found for logger "keystoneclient.client" Unable to communicate with identity service: 404 Not Found The resource could not be found. . (HTTP 404) but after setting these env variables it worked export SERVICE_ENDPOINT=http://192.168.10.15:35357/v2.0 export SERVICE_TOKEN=token but after that for keystone token-get its showing 'Client' object has no attribute 'service_catalog' Why is it so?How can it be fixed any ideas

    Read the article

  • IP Camera working on lan but not on internet

    - by Kevin Boyd
    My IP cam model is Genius 350TR, I tested the cam at home on lan and internet and it worked. Then I shifted it to an office. It works on the office lan setup but I cannot connect to the ip cam from home. The IP cam is configured for port 192.168.0.30:7070 and it has a port forwarded to publicIP:7071 When I telnet to that public IP it connects to that port. However when I try to access the ip cam from a web browser it only shows me the configuration page and settings and the video is blank and it says connecting for some time and then says disconnected. The cam is configured for HTTP on internet and UDP on Lan. The office setup is ISP --- WifiRouter --- PC With Wifi card --- Switch --- IP CAM Is there a way to debug this problem?

    Read the article

  • Getting PHP to work with apache to run .php files through browser

    - by Kevin Duke
    I have VPS running Debian 5.0 (I think) and I would like to get it to run PHP files. I was told it needed to be configured with Apache. I tried entering the command apt-get install apache2 php5 libapache2-mod-php5. But there was no change. Console output: http://pastebin.com/sVMWq6mA This is everything in my /etc/apache2/mods-enabled: http://img35.imageshack.us/img35/6474/modsb.jpg My webserver can be accessed here: http://206.217.223.136/test/ In my test.php file I have the code : <?php phpinfo(); ?> but instead of displaying the page, it tries to download it. How can I fix this?

    Read the article

  • Postgresql spawning a ridiculous number of postmaster processes

    - by Kevin Loney
    For some reason postgres is spawning 700 postmaster processes for handling database requests and the postgres log file if full of 'unexpected EOF on client connection', 'incomplete startup packet' and 'sorry, too many clients already'. netstat tells me that all the open connections are local and I'm pretty sure are coming from postgres internally. This particular instance has been running just fine for the last 230 days or so and nothing has changed configuration wise. Any thoughts on where I should be looking to try and resolve this issue? This is my first time diagnosing a problem like this so if there is any steps I can take to help narrow down the cause that would be helpful as well.

    Read the article

  • How to use Timer broadcast on Multi-Processor system with linux 3.10?

    - by kevin.ji
    Hardware: ARM Cortex-A9 * 2 Software: linux-3.10.0 The platform has 2 cores of arm cortex-a9. Item CONFIG_LOCAL_TIMERS is not set in linux menuconfig. I want to use only one hardware timer to supply tick for all cpu. Interrupts looks like: CPU0 CPU1 57: 6697 0 GIC timer 81: 213 0 GIC uart-pl011 103: 0 0 GIC gmac0 104: 0 0 GIC gmac1 IPI0: 0 1 CPU wakeup interrupts IPI1: 0 0 Timer broadcast interrupts IPI2: 967 866 Rescheduling interrupts IPI3: 0 0 Function call interrupts IPI4: 1 2 Single function call interrupts IPI5: 0 0 CPU stop interrupts IPI6: 0 0 CPU backtrace Err: 0 Timer broadcast interrupts counter does not add. And it looks like that cpu1 does not work at all.But this method works well with linux-3.4, and the interrupt info looks as below in linux-3.4: # cat /proc/interrupts CPU0 CPU1 57: 8596 0 GIC timer 81: 91 0 GIC uart-pl011 103: 0 0 GIC gmac0 104: 0 0 GIC gmac1 IPI0: 0 8560 Timer broadcast interrupts IPI1: 884 1020 Rescheduling interrupts IPI2: 0 0 Function call interrupts IPI3: 0 6 Single function call interrupts IPI4: 0 0 CPU stop interrupts IPI5: 0 0 CPU backtrace Err: 0 The count of Timer broadcast interrupts is adding. And all of cpus work well. I don't know why. Any answer is welcome. :)

    Read the article

  • Launch elasticsearch dockerfile using my own elasticsearch.yml

    - by Kevin
    I am launching elasticsearch via a dockerfile found here: https://index.docker.io/u/ehazlett/elasticsearch/ It works great. I need to define my own hosts as my environment does not support multicast of any kind. I understand that my options are: 1) supply hosts when elasticsearch is run as a command line parameter 2) modify my elasticsearch.yml file to set the hosts. I know how to build the yml, what I need to know is how to launch elasticsearch via docker using my own yml instead of the one in the container. Is that possible? Thanks.

    Read the article

  • Difference between sending data via UDP in Bash and with a Python script

    - by Kevin Burke
    I'm on a Centos box, trying to send a UDP packet to port 8125 on localhost. When I run this Python script: import socket sock = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) sock.sendto('blah', ("127.0.0.1", 8125)) The data appears where it should on port 8125. However when I send the data like this: echo "blah" | nc -4u -w1 127.0.0.1 8125 Or like this: echo "blah" > /dev/udp/127.0.0.1/8125 The data does not appear in the backend. I know this is horribly vague but it's UDP and it's hard to determine why one packet is being sent and the other is not. Do you have any ideas about how to debug this issue further? I'm on a Centos machine.

    Read the article

  • IBM laptop remove access-connections

    - by Kevin
    I installed IBM Access Connections on my IBM t61 laptop to manage my wireless connections but it simply will not connect to my network. I want to uninstall it and try the Intel software which is capable to performing the same task. However, when I go into "Control Panel" - "Add/Remove Programs" and try to "Remove" this package, it simply opens up a screen and closes it immediately. This happens too fast for me to see whether its an error. Has anyone encountered this issue ? The event logs do not show any error.

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >