Search Results

Search found 1138 results on 46 pages for 'units'.

Page 12/46 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • SD Card only mounted after a reboot

    - by evothur
    Hi everyone. I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

    Read the article

  • Creating an in-house single source software development team

    - by alphadogg
    Our company wants to create a single department for all software development efforts (rather than having software development managed by each business unit). Business units would then "outsource" their software needs to this department. What would you setup as concerns/expectations that must be cleared before doing this? For example: Need agreement between units on how much actual time (FTE) is allocated to each unit Need agreement on scheduling of staff need agreement on request procedure if extra time is required by one party etc... Have you been in a situation like this as a manager of one unit destined to use this? If so, what were problems you experienced? What would you have or did implement? Same if you were the manager of the shared team. Please assume, for discussion, that the people concerned know that you can't swap devs in and out on a whim. I don't want to know the disadvantages of this approach; I know them. I want to anticipate issues and know how to mitigate the fallout.

    Read the article

  • Resurrecting a 5,000 line test plan that is a decade old

    - by ale
    I am currently building a test plan for the system I am working on. The plan is 5,000 lines long and about 10 years old. The structure is like this: 1. test title precondition: some W needs to be set up, X needs to be completed action: do some Y postcondition: message saying Z is displayed 2. ... What is this type of testing called ? Is it useful ? It isn't automated.. the tests would have to be handed to some unlucky person to run through and then the results would have to be given to development. It doesn't seem efficient. Is it worth modernising this method of testing (removing tests for removed features, updating tests where different postconditions happen, ...) or would a whole different approach be more appropriate ? We plan to start unit tests but the software requires so much work to actually get 'units' to test - there are no units at present ! Thank you.

    Read the article

  • ubuntu boots only with usb

    - by klimat
    Just installed Ubuntu 11.04. But it boots only from usb. Seems like I didn't pay attention during selecting boot device. sudo fdisk -l [sudo] password for klim: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x000177e1 Device Boot Start End Blocks Id System /dev/sda1 1 60045 482302976 83 Linux /dev/sda2 60045 60802 6080513 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 60045 60802 6080512 82 Linux swap / Solaris Disk /dev/sdb: 4004 MB, 4004511744 bytes 124 heads, 62 sectors/track, 1017 cylinders Units = cylinders of 7688 * 512 = 3936256 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000eee1a Device Boot Start End Blocks Id System /dev/sdb1 * 1 1017 3909317 b W95 FAT32 grub updating or another "grub" operations don't work as I've tried. Can I just copy whole boot folder from usb to HD or smth like that? Any kind of help is appreciated. Apologize for my newbie skills.

    Read the article

  • How can I get rid of the motd message "*** /dev/sdb1 will be checked for errors at next reboot ***"? [duplicate]

    - by kmm
    This question already has an answer here: Persistent “disk will be checked…” in the message of the day (motd) even after reboot 3 answers My motd persistently has: *** /dev/sdb1 will be checked for errors at next reboot *** The problem is that I don't have /dev/sdb1 on my system. I only have /dev/sdb2 (mouted as /) and /dev/sda1 which mounts to /media/backup. I delete that line from /etc/motd, but it reappears after reboot. Here's my df output: Filesystem Size Used Avail Use% Mounted on /dev/sdb2 73G 3.7G 66G 6% / udev 490M 4.0K 490M 1% /dev tmpfs 200M 760K 199M 1% /run none 5.0M 0 5.0M 0% /run/lock none 498M 0 498M 0% /run/shm /dev/sda1 1.9T 429G 1.4T 25% /media/backup Update Here is the output of sudo fdisk -l Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003dfc2 Device Boot Start End Blocks Id System /dev/sda1 63 3907024064 1953512001 83 Linux Disk /dev/sdb: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00049068 Device Boot Start End Blocks Id System /dev/sdb1 152301568 156301311 1999872 82 Linux swap / Solaris /dev/sdb2 * 2048 152301567 76149760 83 Linux Partition table entries are not in disk order I guess /dev/sdb1 is my swap space.

    Read the article

  • Grub not loading after Windows 8 Install

    - by RazorXsr
    My system was configured to dual boot Ubuntu 12.04.1 LTS and Windows 7. Today I got my hands on the MSDN release of Windows 8 and I installed it over my Windows 7. Now the computer just boots to Windows 8 directly without loading the GRUB screen. So I followed the steps as suggested in: https://help.ubuntu.com/community/RecoveringUbuntuAfterInstallingWindows. Running this command: ls -l /dev/disk/by-label/ gives the following output: total 0 lrwxrwxrwx 1 root root 10 Sep 11 07:51 Entertainment -> ../../sda2 lrwxrwxrwx 1 root root 10 Sep 11 02:45 PENDRIVE -> ../../sdb1 Also fdisk -l command gives this as the output: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1246aa23 Device Boot Start End Blocks Id System /dev/sda1 * 2048 319582199 159790076 7 HPFS/NTFS/exFAT /dev/sda2 319582208 602906623 141662208 7 HPFS/NTFS/exFAT /dev/sda3 602908672 625135615 11113472 83 Linux Disk /dev/sdb: 1939 MB, 1939865600 bytes 64 heads, 63 sectors/track, 939 cylinders, total 3788800 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc3072e18 Device Boot Start End Blocks Id System /dev/sdb1 * 2248 3788799 1893276 c W95 FAT32 (LBA) So I assume that I have to run this: sudo grub-install /dev/sda3 to get GRUB up and running. But I am getting this error: /usr/sbin/grub-probe: error: cannot find a device for /boot/grub (is /dev mounted?). Can anyone please guide me in the right direction? The current Ubuntu installation is far too customized to my needs to lose it to a boot manager issue! Any help is much appreciated!

    Read the article

  • How do I get 12.04 to recognize swap partition so that I can hibernate?

    - by Kayla
    I justed installed 12.04 and used gparted to erase and enlarge my swap partition. When I rebooted, gparted said that the file partition for the swap was unknown. Gparted doesn't let me change the file partition to "linux-swap". It does let me change it to NTFS, but when I reboot, it goes back to "unknown". Thanks in advance for your help. Output from sudo swapon -s: Filename Type Size Used Priority /dev/mapper/cryptswap1 partition 9025532 0 -1 Output from sudo fdisk -l: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9d63ac84 Device Boot Start End Blocks Id System /dev/sda1 * 2048 2459647 1228800 7 HPFS/NTFS/exFAT /dev/sda2 2459648 197836472 97688412+ 7 HPFS/NTFS/exFAT /dev/sda3 466890752 488395119 10752184 7 HPFS/NTFS/exFAT /dev/sda4 197836798 466890751 134526977 5 Extended /dev/sda5 197836800 448837631 125500416 83 Linux /dev/sda6 448839680 466890751 9025536 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/mapper/cryptswap1: 9242 MB, 9242148864 bytes 255 heads, 63 sectors/track, 1123 cylinders, total 18051072 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x951b7f53 Disk /dev/mapper/cryptswap1 doesn't contain a valid partition table

    Read the article

  • Mounting a new hard drive (sda1) to my existing filesystem

    - by shank22
    I tried to read some posts regarding mounting a new hard drive, but I am facing some problem. My new hard drive is sda1. The output of sudo fdisk -l is: sudo fdisk -l Disk /dev/sdb: 999.7 GB, 999653638144 bytes 255 heads, 63 sectors/track, 121534 cylinders, total 1952448512 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00016485 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 1935822847 967910400 83 Linux /dev/sdb2 1935824894 1952446463 8310785 5 Extended /dev/sdb5 1935824896 1952446463 8310784 82 Linux swap / Solaris Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x78dbcdc1 Device Boot Start End Blocks Id System /dev/sda1 2048 1953521663 976759808 7 HPFS/NTFS/exFAT What should be done to add this new sda1 hard drive on booting up? What should be added in the /etc/fstab file? I have not performed any partition on the new sda1 drive. I need help on how to proceed from scratch and can't afford to take any risk. Please help!

    Read the article

  • Goodbye XML&hellip; Hello YAML (part 2)

    - by Brian Genisio's House Of Bilz
    Part 1 After I explained my motivation for using YAML instead of XML for my data, I got a lot of people asking me what type of tooling is available in the .Net space for consuming YAML.  In this post, I will discuss a nice tooling option as well as describe some small modifications to leverage the extremely powerful dynamic capabilities of C# 4.0.  I will be referring to the following YAML file throughout this post Recipe: Title: Macaroni and Cheese Description: My favorite comfort food. Author: Brian Genisio TimeToPrepare: 30 Minutes Ingredients: - Name: Cheese Quantity: 3 Units: cups - Name: Macaroni Quantity: 16 Units: oz Steps: - Number: 1 Description: Cook the macaroni - Number: 2 Description: Melt the cheese - Number: 3 Description: Mix the cooked macaroni with the melted cheese Tooling It turns out that there are several implementations of YAML tools out there.  The neatest one, in my opinion, is YAML for .NET, Visual Studio and Powershell.  It includes a great editor plug-in for Visual Studio as well as YamlCore, which is a parsing engine for .Net.  It is in active development still, but it is certainly enough to get you going with YAML in .Net.  Start by referenceing YamlCore.dll, load your document, and you are on your way.  Here is an example of using the parser to get the title of the Recipe: var yaml = YamlLanguage.FileTo("Data.yaml") as Hashtable; var recipe = yaml["Recipe"] as Hashtable; var title = recipe["Title"] as string; In a similar way, you can access data in the Ingredients set: var yaml = YamlLanguage.FileTo("Data.yaml") as Hashtable; var recipe = yaml["Recipe"] as Hashtable; var ingredients = recipe["Ingredients"] as ArrayList; foreach (Hashtable ingredient in ingredients) { var name = ingredient["Name"] as string; } You may have noticed that YamlCore uses non-generic Hashtables and ArrayLists.  This is because YamlCore was designed to work in all .Net versions, including 1.0.  Everything in the parsed tree is one of two things: Hashtable, ArrayList or Value type (usually String).  This translates well to the YAML structure where everything is either a Map, a Set or a Value.  Taking it further Personally, I really dislike writing code like this.  Years ago, I promised myself to never write the words Hashtable or ArrayList in my .Net code again.  They are ugly, mostly depreciated collections that existed before we got generics in C# 2.0.  Now, especially that we have dynamic capabilities in C# 4.0, we can do a lot better than this.  With a relatively small amount of code, you can wrap the Hashtables and Array lists with a dynamic wrapper (wrapper code at the bottom of this post).  The same code can be re-written to look like this: dynamic doc = YamlDoc.Load("Data.yaml"); var title = doc.Recipe.Title; And dynamic doc = YamlDoc.Load("Data.yaml"); foreach (dynamic ingredient in doc.Recipe.Ingredients) { var name = ingredient.Name; } I significantly prefer this code over the previous.  That’s not all… the magic really happens when we take this concept into WPF.  With a single line of code, you can bind to the data dynamically in the view: DataContext = YamlDoc.Load("Data.yaml"); Then, your XAML is extremely straight-forward (Nothing else.  No static types, no adapter code.  Nothing): <StackPanel> <TextBlock Text="{Binding Recipe.Title}" /> <TextBlock Text="{Binding Recipe.Description}" /> <TextBlock Text="{Binding Recipe.Author}" /> <TextBlock Text="{Binding Recipe.TimeToPrepare}" /> <TextBlock Text="Ingredients:" FontWeight="Bold" /> <ItemsControl ItemsSource="{Binding Recipe.Ingredients}" Margin="10,0,0,0"> <ItemsControl.ItemTemplate> <DataTemplate> <StackPanel Orientation="Horizontal"> <TextBlock Text="{Binding Quantity}" /> <TextBlock Text=" " /> <TextBlock Text="{Binding Units}" /> <TextBlock Text=" of " /> <TextBlock Text="{Binding Name}" /> </StackPanel> </DataTemplate> </ItemsControl.ItemTemplate> </ItemsControl> <TextBlock Text="Steps:" FontWeight="Bold" /> <ItemsControl ItemsSource="{Binding Recipe.Steps}" Margin="10,0,0,0"> <ItemsControl.ItemTemplate> <DataTemplate> <StackPanel Orientation="Horizontal"> <TextBlock Text="{Binding Number}" /> <TextBlock Text=": " /> <TextBlock Text="{Binding Description}" /> </StackPanel> </DataTemplate> </ItemsControl.ItemTemplate> </ItemsControl> </StackPanel> This nifty XAML binding trick only works in WPF, unfortunately.  Silverlight handles binding differently, so they don’t support binding to dynamic objects as of late (March 2010).  This, in my opinion, is a major lacking feature in Silverlight and I really hope we will see this feature available to us in Silverlight 4 Release.  (I am not very optimistic for Silverlight 4, but I can hope for the feature in Silverlight 5, can’t I?) Conclusion I still have a few things I want to say about using YAML in the .Net space including de-serialization and using IronRuby for your YAML parser, but this post is hopefully enough to see how easy it is to incorporate YAML documents in your code. Codeplex Site for YAML tools Dynamic wrapper for YamlCore

    Read the article

  • Adventures in Scrum: Lesson 1 &ndash; The failed Sprint

    - by Martin Hinshelwood
    I recently had a conversation with a product owner that wanted to have the Scrum team broken up into smaller units so that less time was wasted on the Scrum Ceremonies! Their complaint was around the need in Scrum to have the entire “Team” (7+-2) involved in the sizing of the work during the “Sprint Planning Meeting”.  The standard flippant answer of all Scrum professionals, “Well that's not Scrum”, does not get you any brownie points in these situations. The response could be “Well we are not doing Scrum then” which in turn leads to “We are doing Scrum…But, we have split the scrum team into units of 2/3 so that they can concentrate on a specific area of work”. While this may work, it is not Scrum and should not be called so… It is just a form of Agile. Don’t get me wrong at this stage, there is nothing wrong with Agile, just don’t call it Scrum. The reason that the Product Owner wants to do this is that, in effect, through a number of miscommunications and failings in our implementation of Scrum, there was NO unit of potentially Shippable software at the end of the first sprint. It does not matter to them that most Scrum teams will fail the first Sprint, even those that are high performing teams. Remember it is the product owners their money! We should NOT break up scrum teams into smaller units for the purpose of having less people tied up in the Scrum Ceremonies. The amount of backlog the Team selects is solely up to the Team… Only the Team can assess what it can accomplish over the upcoming Sprint. - Scrum Guide, Scrum.org The entire team must accept the work and in order to understand what they can accept they must be free to size it as a team. This both encourages common understanding and increases visibility on why team members think a task is of a particular size. This has the benefit of increasing the knowledge of the entire team in the problem domain. A new Team often first realizes that it will either sink or swim as a Team, not individually, in this meeting. The Team realizes that it must rely on itself. As it realizes this, it starts to self-organize to take on the characteristics and behaviour of a real Team. - Scrum Guide, Scrum.org This paragraph goes to the why of having the whole team at the meeting; The goal of Scrum it to produce a unit of potentially shippable software at the end of every Sprint. In order to achieve this we need high performing teams and this is what Scrum as a framework has been optimised to produce. I think that our Product Owner is understandably upset over loosing two weeks work and is losing sight the end goal of Scrum in the failures of the moment. As the man spending the money, I completely understand his perspective and I think that we should not have started Scrum on an internal project, but selected a customer  that is open to the ideas and complications of Scrum. So, what should we have NOT done on our first Scrum project: Should not have had 3 interns as the only on site resource – This lead to bad practices as the experienced guys were not there helping and correcting as they usually would. Should not have had the only experienced guys offsite – With both the experienced technical guys in completely different time zones it was difficult to get time for questions. Helping the guys on site was just plain impossible. Should not have used a part time ScrumMaster – Although the ScrumMaster attended all of the Ceremonies, because they are only in 2 full days of the week it makes it difficult for the team to raise impediments as they go. Should not have used a proxy product owner. – This was probably the worst decision that was made. Mainly because the proxy product owner did not have the same vision as the product owner. While Scrum does not explicitly reject the idea of a Proxy Product Owner, I do not think it works very well in practice. The “single wringable neck” needs to contain both the Money and the Vision as well as attending the required meetings. I will be brining all of these things up at the Sprint Retrospective and we will learn from our mistakes and move on. Do, Inspect then Adapt…   Technorati Tags: Scrum,Sprint Planing,Sprint Retrospective,Scrum.org,Scrum Guide,Scrum Ceremonies,Scrummaster,Product Owner Need Help? Professional Scrum Developer Training SSW has six Professional Scrum Developer Trainers who specialise in training your developers in implementing Scrum with Microsoft's Visual Studio ALM tools.

    Read the article

  • how to retain the animated position in opengl es 2.0

    - by Arun AC
    I am doing frame based animation for 300 frames in opengl es 2.0 I want a rectangle to translate by +200 pixels in X axis and also scaled up by double (2 units) in the first 100 frames Then, the animated rectangle has to stay there for the next 100 frames. Then, I want the same animated rectangle to translate by +200 pixels in X axis and also scaled down by half (0.5 units) in the last 100 frames. I am using simple linear interpolation to calculate the delta-animation value for each frame. Pseudo code: The below drawFrame() is executed for 300 times (300 frames) in a loop. float RectMVMatrix[4][4] = {1, 0, 0, 0, 0, 1, 0, 0, 0, 0, 1, 0, 0, 0, 0, 1 }; // identity matrix int totalframes = 300; float translate-delta; // interpolated translation value for each frame float scale-delta; // interpolated scale value for each frame // The usual code for draw is: void drawFrame(int iCurrentFrame) { // mySetIdentity(RectMVMatrix); // comment this line to retain the animated position. mytranslate(RectMVMatrix, translate-delta, X_AXIS); // to translate the mv matrix in x axis by translate-delta value myscale(RectMVMatrix, scale-delta); // to scale the mv matrix by scale-delta value ... // opengl calls glDrawArrays(...); eglswapbuffers(...); } The above code will work fine for first 100 frames. in order to retain the animated rectangle during the frames 101 to 200, i removed the "mySetIdentity(RectMVMatrix);" in the above drawFrame(). Now on entering the drawFrame() for the 2nd frame, the RectMVMatrix will have the animated value of first frame e.g. RectMVMatrix[4][4] = { 1.01, 0, 0, 2, 0, 1, 0, 0, 0, 0, 1, 0, 0, 0, 0, 1 };// 2 pixels translation and 1.01 units scaling after first frame This RectMVMatrix is used for mytranslate() in 2nd frame. The translate function will affect the value of "RectMVMatrix[0][0]". Thus translation affects the scaling values also. Eventually output is getting wrong. How to retain the animated position without affecting the current ModelView matrix? =========================================== I got the solution... Thanks to Sergio. I created separate matrices for translation and scaling. e.g.CurrentTranslateMatrix[4][4], CurrentScaleMatrix[4][4]. Then for every frame, I reset 'CurrentTranslateMatrix' to identity and call mytranslate( CurrentTranslateMatrix, translate-delta, X_AXIS) function. I reset 'CurrentScaleMatrix' to identity and call myscale(CurrentScaleMatrix, scale-delta) function. Then, I multiplied these 'CurrentTranslateMatrix' and 'CurrentScaleMatrix' to get the final 'RectMVMatrix' Matrix for the frame. Pseudo Code: float RectMVMatrix[4][4] = {0}; float CurrentTranslateMatrix[4][4] = {0}; float CurrentScaleMatrix[4][4] = {0}; int iTotalFrames = 300; int iAnimationFrames = 100; int iTranslate_X = 200.0f; // in pixels float fScale_X = 2.0f; float scaleDelta; float translateDelta_X; void DrawRect(int iTotalFrames) { mySetIdentity(RectMVMatrix); for (int i = 0; i< iTotalFrames; i++) { DrawFrame(int iCurrentFrame); } } void getInterpolatedValue(int iStartFrame, int iEndFrame, int iTotalFrame, int iCurrentFrame, float *scaleDelta, float *translateDelta_X) { float fDelta = float ( (iCurrentFrame - iStartFrame) / (iEndFrame - iStartFrame)) float fStartX = 0.0f; float fEndX = ConvertPixelsToOpenGLUnit(iTranslate_X); *translateDelta_X = fStartX + fDelta * (fEndX - fStartX); float fStartScaleX = 1.0f; float fEndScaleX = fScale_X; *scaleDelta = fStartScaleX + fDelta * (fEndScaleX - fStartScaleX); } void DrawFrame(int iCurrentFrame) { getInterpolatedValue(0, iAnimationFrames, iTotalFrames, iCurrentFrame, &scaleDelta, &translateDelta_X) mySetIdentity(CurrentTranslateMatrix); myTranslate(RectMVMatrix, translateDelta_X, X_AXIS); // to translate the mv matrix in x axis by translate-delta value mySetIdentity(CurrentScaleMatrix); myScale(RectMVMatrix, scaleDelta); // to scale the mv matrix by scale-delta value myMultiplyMatrix(RectMVMatrix, CurrentTranslateMatrix, CurrentScaleMatrix);// RectMVMatrix = CurrentTranslateMatrix*CurrentScaleMatrix; ... // opengl calls glDrawArrays(...); eglswapbuffers(...); } I maintained this 'RectMVMatrix' value, if there is no animation for the current frame (e.g. 101th frame onwards). Thanks, Arun AC

    Read the article

  • Why do we use Pythagoras in game physics?

    - by Starkers
    I've recently learned that we use Pythagoras a lot in our physics calculations and I'm afraid I don't really get the point. Here's an example from a book to make sure an object doesn't travel faster than a MAXIMUM_VELOCITY constant in the horizontal plane: MAXIMUM_VELOCITY = <any number>; SQUARED_MAXIMUM_VELOCITY = MAXIMUM_VELOCITY * MAXIMUM_VELOCITY; function animate(){ var squared_horizontal_velocity = (x_velocity * x_velocity) + (z_velocity * z_velocity); if( squared_horizontal_velocity <= SQUARED_MAXIMUM_VELOCITY ){ scalar = squared_horizontal_velocity / SQUARED_MAXIMUM_VELOCITY; x_velocity = x_velocity / scalar; z_velocity = x_velocity / scalar; } } Let's try this with some numbers: An object is attempting to move 5 units in x and 5 units in z. It should only be able to move 5 units horizontally in total! MAXIMUM_VELOCITY = 5; SQUARED_MAXIMUM_VELOCITY = 5 * 5; SQUARED_MAXIMUM_VELOCITY = 25; function animate(){ var x_velocity = 5; var z_velocity = 5; var squared_horizontal_velocity = (x_velocity * x_velocity) + (z_velocity * z_velocity); var squared_horizontal_velocity = 5 * 5 + 5 * 5; var squared_horizontal_velocity = 25 + 25; var squared_horizontal_velocity = 50; // if( squared_horizontal_velocity <= SQUARED_MAXIMUM_VELOCITY ){ if( 50 <= 25 ){ scalar = squared_horizontal_velocity / SQUARED_MAXIMUM_VELOCITY; scalar = 50 / 25; scalar = 2.0; x_velocity = x_velocity / scalar; x_velocity = 5 / 2.0; x_velocity = 2.5; z_velocity = z_velocity / scalar; z_velocity = 5 / 2.0; z_velocity = 2.5; // new_horizontal_velocity = x_velocity + z_velocity // new_horizontal_velocity = 2.5 + 2.5 // new_horizontal_velocity = 5 } } Now this works well, but we can do the same thing without Pythagoras: MAXIMUM_VELOCITY = 5; function animate(){ var x_velocity = 5; var z_velocity = 5; var horizontal_velocity = x_velocity + z_velocity; var horizontal_velocity = 5 + 5; var horizontal_velocity = 10; // if( horizontal_velocity >= MAXIMUM_VELOCITY ){ if( 10 >= 5 ){ scalar = horizontal_velocity / MAXIMUM_VELOCITY; scalar = 10 / 5; scalar = 2.0; x_velocity = x_velocity / scalar; x_velocity = 5 / 2.0; x_velocity = 2.5; z_velocity = z_velocity / scalar; z_velocity = 5 / 2.0; z_velocity = 2.5; // new_horizontal_velocity = x_velocity + z_velocity // new_horizontal_velocity = 2.5 + 2.5 // new_horizontal_velocity = 5 } } Benefits of doing it without Pythagoras: Less lines Within those lines, it's easier to read what's going on ...and it takes less time to compute, as there are less multiplications Seems to me like computers and humans get a better deal without Pythagoras! However, I'm sure I'm wrong as I've seen Pythagoras' theorem in a number of reputable places, so I'd like someone to explain me the benefit of using Pythagoras to a maths newbie. Does this have anything to do with unit vectors? To me a unit vector is when we normalize a vector and turn it into a fraction. We do this by dividing the vector by a larger constant. I'm not sure what constant it is. The total size of the graph? Anyway, because it's a fraction, I take it, a unit vector is basically a graph that can fit inside a 3D grid with the x-axis running from -1 to 1, z-axis running from -1 to 1, and the y-axis running from -1 to 1. That's literally everything I know about unit vectors... not much :P And I fail to see their usefulness. Also, we're not really creating a unit vector in the above examples. Should I be determining the scalar like this: // a mathematical work-around of my own invention. There may be a cleverer way to do this! I've also made up my own terms such as 'divisive_scalar' so don't bother googling var divisive_scalar = (squared_horizontal_velocity / SQUARED_MAXIMUM_VELOCITY); var divisive_scalar = ( 50 / 25 ); var divisive_scalar = 2; var multiplicative_scalar = (divisive_scalar / (2*divisive_scalar)); var multiplicative_scalar = (2 / (2*2)); var multiplicative_scalar = (2 / 4); var multiplicative_scalar = 0.5; x_velocity = x_velocity * multiplicative_scalar x_velocity = 5 * 0.5 x_velocity = 2.5 Again, I can't see why this is better, but it's more "unit-vector-y" because the multiplicative_scalar is a unit_vector? As you can see, I use words such as "unit-vector-y" so I'm really not a maths whiz! Also aware that unit vectors might have nothing to do with Pythagoras so ignore all of this if I'm barking up the wrong tree. I'm a very visual person (3D modeller and concept artist by trade!) and I find diagrams and graphs really, really helpful so as many as humanely possible please!

    Read the article

  • Why do we use the Pythagorean theorem in game physics?

    - by Starkers
    I've recently learned that we use Pythagorean theorem a lot in our physics calculations and I'm afraid I don't really get the point. Here's an example from a book to make sure an object doesn't travel faster than a MAXIMUM_VELOCITY constant in the horizontal plane: MAXIMUM_VELOCITY = <any number>; SQUARED_MAXIMUM_VELOCITY = MAXIMUM_VELOCITY * MAXIMUM_VELOCITY; function animate(){ var squared_horizontal_velocity = (x_velocity * x_velocity) + (z_velocity * z_velocity); if( squared_horizontal_velocity <= SQUARED_MAXIMUM_VELOCITY ){ scalar = squared_horizontal_velocity / SQUARED_MAXIMUM_VELOCITY; x_velocity = x_velocity / scalar; z_velocity = x_velocity / scalar; } } Let's try this with some numbers: An object is attempting to move 5 units in x and 5 units in z. It should only be able to move 5 units horizontally in total! MAXIMUM_VELOCITY = 5; SQUARED_MAXIMUM_VELOCITY = 5 * 5; SQUARED_MAXIMUM_VELOCITY = 25; function animate(){ var x_velocity = 5; var z_velocity = 5; var squared_horizontal_velocity = (x_velocity * x_velocity) + (z_velocity * z_velocity); var squared_horizontal_velocity = 5 * 5 + 5 * 5; var squared_horizontal_velocity = 25 + 25; var squared_horizontal_velocity = 50; // if( squared_horizontal_velocity <= SQUARED_MAXIMUM_VELOCITY ){ if( 50 <= 25 ){ scalar = squared_horizontal_velocity / SQUARED_MAXIMUM_VELOCITY; scalar = 50 / 25; scalar = 2.0; x_velocity = x_velocity / scalar; x_velocity = 5 / 2.0; x_velocity = 2.5; z_velocity = z_velocity / scalar; z_velocity = 5 / 2.0; z_velocity = 2.5; // new_horizontal_velocity = x_velocity + z_velocity // new_horizontal_velocity = 2.5 + 2.5 // new_horizontal_velocity = 5 } } Now this works well, but we can do the same thing without Pythagoras: MAXIMUM_VELOCITY = 5; function animate(){ var x_velocity = 5; var z_velocity = 5; var horizontal_velocity = x_velocity + z_velocity; var horizontal_velocity = 5 + 5; var horizontal_velocity = 10; // if( horizontal_velocity >= MAXIMUM_VELOCITY ){ if( 10 >= 5 ){ scalar = horizontal_velocity / MAXIMUM_VELOCITY; scalar = 10 / 5; scalar = 2.0; x_velocity = x_velocity / scalar; x_velocity = 5 / 2.0; x_velocity = 2.5; z_velocity = z_velocity / scalar; z_velocity = 5 / 2.0; z_velocity = 2.5; // new_horizontal_velocity = x_velocity + z_velocity // new_horizontal_velocity = 2.5 + 2.5 // new_horizontal_velocity = 5 } } Benefits of doing it without Pythagoras: Less lines Within those lines, it's easier to read what's going on ...and it takes less time to compute, as there are less multiplications Seems to me like computers and humans get a better deal without Pythagorean theorem! However, I'm sure I'm wrong as I've seen Pythagoras' theorem in a number of reputable places, so I'd like someone to explain me the benefit of using Pythagorean theorem to a maths newbie. Does this have anything to do with unit vectors? To me a unit vector is when we normalize a vector and turn it into a fraction. We do this by dividing the vector by a larger constant. I'm not sure what constant it is. The total size of the graph? Anyway, because it's a fraction, I take it, a unit vector is basically a graph that can fit inside a 3D grid with the x-axis running from -1 to 1, z-axis running from -1 to 1, and the y-axis running from -1 to 1. That's literally everything I know about unit vectors... not much :P And I fail to see their usefulness. Also, we're not really creating a unit vector in the above examples. Should I be determining the scalar like this: // a mathematical work-around of my own invention. There may be a cleverer way to do this! I've also made up my own terms such as 'divisive_scalar' so don't bother googling var divisive_scalar = (squared_horizontal_velocity / SQUARED_MAXIMUM_VELOCITY); var divisive_scalar = ( 50 / 25 ); var divisive_scalar = 2; var multiplicative_scalar = (divisive_scalar / (2*divisive_scalar)); var multiplicative_scalar = (2 / (2*2)); var multiplicative_scalar = (2 / 4); var multiplicative_scalar = 0.5; x_velocity = x_velocity * multiplicative_scalar x_velocity = 5 * 0.5 x_velocity = 2.5 Again, I can't see why this is better, but it's more "unit-vector-y" because the multiplicative_scalar is a unit_vector? As you can see, I use words such as "unit-vector-y" so I'm really not a maths whiz! Also aware that unit vectors might have nothing to do with Pythagorean theorem so ignore all of this if I'm barking up the wrong tree. I'm a very visual person (3D modeller and concept artist by trade!) and I find diagrams and graphs really, really helpful so as many as humanely possible please!

    Read the article

  • Mounting ddrescue image after recovery (in over my head)

    - by BorgDomination
    I'm having problems mounting the recovery image. I've tried to mount the image multiple ways. quark@DS9 ~ $ sudo mount -t ext4 /media/jump1/1recover/sdb1.img /mnt mount: wrong fs type, bad option, bad superblock on /dev/loop0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so quark@DS9 ~ $ sudo mount -r -o loop /media/jump1/1recover/sdb1.img recover mount: you must specify the filesystem type quark@DS9 ~ $ sudo mount /media/jump1/1recover/sdb1.img mnt mount: you must specify the filesystem type It doesn't even give me detailed information on the file I just made, nautilus says it's 160gb. quark@DS9 ~ $ file /media/jump1/1recover/sdb1.img /media/jump1/1recover/sdb1.img: data quark@DS9 ~ $ mmls /media/jump1/1recover/sdb1.img Cannot determine partition type I'm not sure what I'm doing wrong or if I started this process incorrectly from the beginning. I've outlined what I've done so far below. I'm clueless, I'd appreciate if someone had some input for me. What I have done from the beginning My laptop has two hard drives. One has the dual boot Win7 / Linux Mint system files. Secondary one contained my /home folder. The laptop was jarred and the /home disk was broken. I tried a LiveCD recovery, it failed. Wouldn't even load a Live session with the disk installed. So I turned to ddrescue. quark@DS9 ~ $ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009fc18 Device Boot Start End Blocks Id System /dev/sda1 * 2048 112642047 56320000 7 HPFS/NTFS/exFAT /dev/sda2 138033152 312580095 87273472 83 Linux /dev/sda3 112644094 138033151 12694529 5 Extended /dev/sda5 112644096 132173823 9764864 83 Linux /dev/sda6 132175872 138033151 2928640 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdb: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002a8ea Device Boot Start End Blocks Id System /dev/sdb1 * 63 312576704 156288321 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed6d054b Device Boot Start End Blocks Id System /dev/sdc1 63 1953520064 976760001 7 HPFS/NTFS/exFAT sda - 160g internal, holds all system files and all computer functions. sdb - 160g internal, BROKEN, contains about 140g of data I'd like to recover. sdc - 1T external, contains recovery image. Only place that has space to do all this. From this site, https://apps.education.ucsb.edu/wiki/Ddrescue I used this script to create an image of the broken hard drive. I changed the destination to the external USB drive. #!/bin/sh prt=sdb1 src=/dev/$prt dst=/media/jump1/1recover/$prt.img log=$dst.log sudo time ddrescue --no-split $src $dst $log sudo time ddrescue --direct --max-retries=3 $src $dst $log sudo time ddrescue --direct --retrim --max-retries=3 $src $dst $log Everything looked like it came off without a hitch: quark@DS9 ~ $ sudo bash recover1 Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 0 B, errsize: 0 B, errors: 0 Current status rescued: 160039 MB, errsize: 4096 B, current rate: 35588 B/s ipos: 3584 B, errors: 1, average rate: 22859 kB/s opos: 3584 B, time from last successful read: 0 s Finished 12.78user 1060.42system 1:56:41elapsed 15%CPU (0avgtext+0avgdata 4944maxresident)k 312580958inputs+0outputs (1major+601minor)pagefaults 0swaps Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 160039 MB, errsize: 4096 B, errors: 1 Current status rescued: 160039 MB, errsize: 1024 B, current rate: 0 B/s ipos: 1536 B, errors: 1, average rate: 13 B/s opos: 1536 B, time from last successful read: 1.3 m Finished 0.00user 0.00system 3:43.95elapsed 0%CPU (0avgtext+0avgdata 4944maxresident)k 238inputs+0outputs (3major+374minor)pagefaults 0swaps Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 160039 MB, errsize: 1024 B, errors: 1 Current status rescued: 160039 MB, errsize: 1024 B, current rate: 0 B/s ipos: 1536 B, errors: 1, average rate: 0 B/s opos: 1536 B, time from last successful read: 3.7 m Finished 0.00user 0.00system 3:43.56elapsed 0%CPU (0avgtext+0avgdata 4944maxresident)k 8inputs+0outputs (0major+376minor)pagefaults 0swaps It looks like, from where I'm standing it worked perfectly. Here's the log: # Rescue Logfile. Created by GNU ddrescue version 1.14 # Command line: ddrescue --direct --retrim --max-retries=3 /dev/sdb1 /media/jump1/1recover/sdb1.img /media/jump1/1recover/sdb1.img.log # current_pos current_status 0x00000600 + # pos size status 0x00000000 0x00000400 + 0x00000400 0x00000400 - 0x00000800 0x254314FC00 + I'm not sure how to proceed. Does this mean all of my data is lost???????? Appreciate ANY input!

    Read the article

  • Dual booting on separate hard drives

    - by tornadorider
    I have windows XP professional installed on 1 hard drive and Ubuntu 10.10 on my second hard drive. On start up the computer completely skips the grub menu and boots straight into 10.10. I have tried running os-prober with the windows hard drive mounted and then updating grub but it didnt work. Any ideas? I have changed the boot order so that the HDD with xp on it is first however the computer still booted into linux. I tried running grub-install /dev/sda and got this /usr/sbin/grub-setup: warn: Sector 32 is already in use by FlexNet; avoiding it. This software may cause boot or other problems in future. Please ask its authors not to store data in the boot track.. /usr/sbin/grub-setup: warn: Sector 33 is already in use by FlexNet; avoiding it. This software may cause boot or other problems in future. Please ask its authors not to store data in the boot track.. Installation finished. No error reported I checked using disk utility and the code for my xp hard drive is sdb so i ran the camand grub-install /dev/sdb shich gave me this Installation finished. No error reported. So i rebooted but it still didnt work. Any other ideas? Additional info gedit /boot/grub/grub.cfg: # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-22-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-22-generic ...' linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-22-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### sudo fdisk -l: Disk /dev/sda: 80.1 GB, 80060424192 bytes 255 heads, 63 sectors/track, 9733 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008a483 Device Boot Start End Blocks Id System /dev/sda1 * 1 9352 75112448 83 Linux /dev/sda2 9352 9734 3068929 5 Extended /dev/sda5 9352 9734 3068928 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc5d6c5d6 Device Boot Start End Blocks Id System /dev/sdb1 1 60800 488375968+ 7 HPFS/NTFS sudo blkid /dev/sda1: UUID="d682c9bd-dd89-4827-9802-a1f921ebe21c" TYPE="ext4" /dev/sda5: UUID="09e9c2cb-d903-4f0b-a181-536951845231" TYPE="swap" /dev/sdb1: UUID="B21844EB1844AFE1" TYPE="ntfs" sudo os-prober (nothing) Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in partition #1 for (,msdos1)/boot/grub. => Grub 2 is installed in the MBR of /dev/sdb and looks on the same drive in partition #1 for (,msdos1)/boot/grub. sda1: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 10.10 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sda2: _________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows XP Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows XP Boot files/dirs: =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Disk /dev/sda: 80.1 GB, 80060424192 bytes 255 heads, 63 sectors/track, 9733 cylinders, total 156368016 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sda1 * 2,048 150,226,943 150,224,896 83 Linux /dev/sda2 150,228,990 156,366,847 6,137,858 5 Extended /dev/sda5 150,228,992 156,366,847 6,137,856 82 Linux swap / Solaris Drive: sdb ___________________ _____________________________________________________ Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start End Size Id System /dev/sdb1 * 63 976,751,999 976,751,937 7 HPFS/NTFS blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/sda1 d682c9bd-dd89-4827-9802-a1f921ebe21c ext4 /dev/sda2: PTTYPE="dos" /dev/sda5 09e9c2cb-d903-4f0b-a181-536951845231 swap /dev/sda: PTTYPE="dos" /dev/sdb1 B21844EB1844AFE1 ntfs /dev/sdb: PTTYPE="dos" ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sda1 / ext4 (rw,errors=remount-ro,commit=0) =========================== sda1/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga } insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c set locale_dir=($root)/boot/grub/locale set lang=en insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro quiet splash initrd /boot/initrd.img-2.6.35-22-generic } menuentry 'Ubuntu, with Linux 2.6.35-22-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c echo 'Loading Linux 2.6.35-22-generic ...' linux /boot/vmlinuz-2.6.35-22-generic root=UUID=d682c9bd-dd89-4827-9802-a1f921ebe21c ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-22-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set d682c9bd-dd89-4827-9802-a1f921ebe21c linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. menuentry "Windows XP" { set root=(hd1,1) chainloader (hd1,1)+1 } ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sda1/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/sda1 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=09e9c2cb-d903-4f0b-a181-536951845231 none swap sw 0 0 =================== sda1: Location of files loaded by Grub: =================== 51.7GB: boot/grub/core.img 58.5GB: boot/grub/grub.cfg 1.2GB: boot/initrd.img-2.6.35-22-generic 1.3GB: boot/initrd.img-2.6.35-28-generic 58.2GB: boot/vmlinuz-2.6.35-22-generic 51.7GB: boot/vmlinuz-2.6.35-28-generic 1.3GB: initrd.img 1.2GB: initrd.img.old 51.7GB: vmlinuz 58.2GB: vmlinuz.old =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on sda2 00000000 d9 ed 13 ab ff a8 33 8c 01 b2 47 99 e1 4a b1 f1 |......3...G..J..| 00000010 69 5f a7 29 a4 1a 03 9e 31 b9 45 02 71 e6 58 78 |i_.)....1.E.q.Xx| 00000020 3d f6 ee 7b 3e 33 1b 82 c6 7d cf 1a c8 e7 bc 2f |=..{>3...}...../| 00000030 b9 e1 70 75 cf 18 aa e7 d5 7e 3c f1 b4 e7 9e 3a |..pu.....~<....:| 00000040 55 38 f1 b4 ee 78 59 0b 5e f7 3c 4c 57 73 9c 2a |U8...xY.^.<LWs.*| 00000050 28 f1 19 ed 11 9c b2 19 e2 80 92 1c 7b 84 ee 0b |(...........{...| 00000060 e2 c0 ac af 0a 50 42 b9 cf 0c dc 2c 20 77 85 dc |.....PB...., w..| 00000070 8f 70 5f 7b 84 9b a1 f7 8c 2d ee 70 5c ae f7 39 |.p_{.....-.p\..9| 00000080 63 f7 09 8a ec 79 4c ed 9f cc ad 3c f8 1b 47 7d |c....yL....<..G}| 00000090 3f 97 d5 16 cb 29 45 38 25 61 36 08 de 10 93 0f |?....)E8%a6.....| 000000a0 95 4f ea 54 f9 89 ff f1 bf 9a cc bb fd b6 22 b1 |.O.T..........".| 000000b0 65 08 05 21 78 19 46 b0 24 7e fb de d4 b3 ba d6 |e..!x.F.$~......| 000000c0 ec 11 65 82 ee 10 1d 12 04 91 da 6d 67 47 ea 9b |..e........mgG..| 000000d0 6f b0 aa fb cb 67 10 64 86 e8 26 85 fb f9 50 77 |o....g.d..&...Pw| 000000e0 9d 13 9b 9e d9 11 f3 a1 50 1b 11 b7 93 79 9f ab |........P....y..| 000000f0 c1 b6 86 0f 35 ed d4 9f dc f8 db bd ed 45 3a 68 |....5........E:h| 00000100 54 68 4a 1d d1 fc b8 c9 72 b4 d7 7b 60 e7 39 2f |ThJ.....r..{`.9/| 00000110 2a 0a 4e 52 72 52 c6 e2 2a 55 6a 2a e1 82 40 71 |*.NRrR..*Uj*..@q| 00000120 11 11 e0 53 d6 ff 1b a9 c6 65 df 1e b7 15 6f a2 |...S.....e....o.| 00000130 15 02 a4 6d 19 b7 78 57 a6 ee 9e 36 08 7d 6f 7c |...m..xW...6.}o|| 00000140 fd f7 7c d5 40 ff 0f c7 97 dc aa 00 ce 8b bb dc |..|.@...........| 00000150 e2 eb 1c 50 74 d8 14 cc 9a d6 5c a2 ab f2 67 f9 |...Pt.....\...g.| 00000160 58 ed 43 79 0e 78 7a 5c a6 f8 7b e8 05 4e 62 8a |X.Cy.xz\..{..Nb.| 00000170 0a 5f 22 ee a6 38 b9 e1 32 45 97 08 cc 75 66 c6 |._"..8..2E...uf.| 00000180 b3 a2 2d 89 a1 e9 95 21 28 53 fd dd be b1 b2 a2 |..-....!(S......| 00000190 78 3f a3 c9 3d e3 31 54 88 cf 78 0d e1 21 a8 74 |x?..=.1T..x..!.t| 000001a0 06 60 9d 21 c6 7a 24 e1 cc 28 f8 98 e0 99 e3 fc |.`.!.z$..(......| 000001b0 fa 8b eb d5 56 03 20 b8 54 ba c6 ee 9f 57 00 fe |....V. .T....W..| 000001c0 ff ff 82 fe ff ff 02 00 00 00 00 a8 5d 00 00 00 |............]...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200

    Read the article

  • Changing CSS on the fly in a UIWebView on iPhone

    - by Shaggy Frog
    Let's say I'm developing an iPhone app that is a catalogue of cars. The user will choose a car from a list, and I will present a detail view for the car, which will describe things like top speed. The detail view will essentially be a UIWebView that is loading an existing HTML file. Different users will live in different parts of the world, so they will like to see the top speed for the car in whatever units are appropriate for their locale. Let's say there are two such units: SI (km/h) and conventional (mph). Let's also say the user will be able to change the display units by hitting a button on the screen; when that happens, the detail screen should switch to show the relevant units. So far, here's what I've done to try and solve this. The HTML might look something like this: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" xml:lang="en-US" lang="en-US"> <head> <title>Some Car</title> <link rel="stylesheet" media="screen" type="text/css" href="persistent.css" /> <link rel="alternate stylesheet" media="screen" type="text/css" href="si.css" title="si" /> <link rel="alternate stylesheet" media="screen" type="text/css" href="conventional.css" title="conventional" /> <script type="text/javascript" src="switch.js"></script> </head> <body> <h1>Some Car</h1> <div id="si"> <h2>Top Speed: 160 km/h</h2> </div> <div id="conventional"> <h2>Top Speed: 100 mph</h2> </div> </body> The peristent stylesheet, persistent.css: #si { display:none; } #conventional { display:none; } The first alternate stylesheet, si.css: #si { display:inline; } #conventional { display:none; } And the second alternate stylesheet, conventional.css: #si { display:none; } #conventional { display:inline; } Based on a tutorial at A List Apart, my switch.js looks something like this: function disableStyleSheet(title) { var i, a; for (i = 0; (a = document.getElementsByTagName("link")[i]); i++) { if ((a.getAttribute("rel").indexOf("alt") != -1) && (a.getAttribute("title") == title)) { a.disabled = true; } } } function enableStyleSheet(title) { var i, a; for (i = 0; (a = document.getElementsByTagName("link")[i]); i++) { if ((a.getAttribute("rel").indexOf("alt") != -1) && (a.getAttribute("title") == title)) { a.disabled = false; } } } function switchToSiStyleSheet() { disableStyleSheet("conventional"); enableStyleSheet("si"); } function switchToConventionalStyleSheet() { disableStyleSheet("si"); enableStyleSheet("conventional"); } My button action handler looks something like this: - (void)notesButtonAction:(id)sender { static BOOL isUsingSi = YES; if (isUsingSi) { NSString* command = [[NSString alloc] initWithString:@"switchToSiStyleSheet();"]; [self.webView stringByEvaluatingJavaScriptFromString:command]; [command release]; } else { NSString* command = [[NSString alloc] initWithFormat:@"switchToConventionalStyleSheet();"]; [self.webView stringByEvaluatingJavaScriptFromString:command]; [command release]; } isUsingSi = !isUsingSi; } Here's the first problem. The first time the button is hit, the UIWebView doesn't change. The second time it's hit, it looks like the conventional style sheet is loaded. The third time, it switches to the SI style sheet; the fourth time, back to the conventional, and so on. So, basically, only that first button press doesn't seem to do anything. Here's the second problem. I'm not sure how to switch to the correct style sheet upon initial load of the UIWebView. I tried this: - (void)webViewDidFinishLoad:(UIWebView *)webView { NSString* command = [[NSString alloc] initWithString:@"switchToSiStyleSheet();"]; [self.webView stringByEvaluatingJavaScriptFromString:command]; [command release]; } But, like the first button hit, it doesn't seem to do anything. Can anyone help me with these two problems?

    Read the article

  • Issues using a Fedex Webservice via WDSL/SOAP

    - by Parris
    Hi Everyone, I downloaded the sample code to request a rate from fedex's website... i placed the WSDL file in the proper location, I have my acct number, password, meter number, and key. When I run the script I get this error: Error in processing transaction. ERROR prof 1000 Authentication Failed The script they give is as follows, and yes i do actually replace the XXX and YYY everywhere it says.: <?php // Copyright 2009, FedEx Corporation. All rights reserved. // Version 7.0.0 require_once('fedex-common.php5'); $newline = "<br />"; //The WSDL is not included with the sample code. //Please include and reference in $path_to_wsdl variable. $path_to_wsdl = "RateService_v7.wsdl"; ini_set("soap.wsdl_cache_enabled", "0"); $client = new SoapClient($path_to_wsdl, array('trace' => 1)); // Refer to http://us3.php.net/manual/en/ref.soap.php for more information $request['WebAuthenticationDetail'] = array('UserCredential' => array('Key' => 'XXX', 'Password' => 'YYY')); // Replace 'XXX' and 'YYY' with FedEx provided credentials $request['ClientDetail'] = array('AccountNumber' => 'XXX', 'MeterNumber' => 'YYY');// Replace 'XXX' with your account and meter number $request['TransactionDetail'] = array('CustomerTransactionId' => ' *** Rate Request v7 using PHP ***'); $request['Version'] = array('ServiceId' => 'crs', 'Major' => '7', 'Intermediate' => '0', 'Minor' => '0'); $request['ReturnTransitAndCommit'] = true; $request['RequestedShipment']['DropoffType'] = 'REGULAR_PICKUP'; // valid values REGULAR_PICKUP, REQUEST_COURIER, ... $request['RequestedShipment']['ShipTimestamp'] = date('c'); $request['RequestedShipment']['ServiceType'] = 'FEDEX_GROUND'; // valid values STANDARD_OVERNIGHT, PRIORITY_OVERNIGHT, FEDEX_GROUND, ... $request['RequestedShipment']['PackagingType'] = 'YOUR_PACKAGING'; // valid values FEDEX_BOX, FEDEX_PAK, FEDEX_TUBE, YOUR_PACKAGING, ... $request['RequestedShipment']['Shipper'] = array('Address' => array( 'StreetLines' => array('10 Fed Ex Pkwy'), // Origin details 'City' => 'Memphis', 'StateOrProvinceCode' => 'TN', 'PostalCode' => '38115', 'CountryCode' => 'US')); $request['RequestedShipment']['Recipient'] = array('Address' => array ( 'StreetLines' => array('13450 Farmcrest Ct'), // Destination details 'City' => 'Herndon', 'StateOrProvinceCode' => 'VA', 'PostalCode' => '20171', 'CountryCode' => 'US')); $request['RequestedShipment']['ShippingChargesPayment'] = array('PaymentType' => 'SENDER', 'Payor' => array('AccountNumber' => 'XXX', // Replace 'XXX' with payor's account number 'CountryCode' => 'US')); $request['RequestedShipment']['RateRequestTypes'] = 'ACCOUNT'; $request['RequestedShipment']['RateRequestTypes'] = 'LIST'; $request['RequestedShipment']['PackageCount'] = '2'; $request['RequestedShipment']['PackageDetailSpecified'] = true; $request['RequestedShipment']['PackageDetail'] = 'INDIVIDUAL_PACKAGES'; // Or PACKAGE_SUMMARY $request['RequestedShipment']['RequestedPackageLineItems'] = array('0' => array('Weight' => array('Value' => 2.0, 'Units' => 'LB'), 'Dimensions' => array('Length' => 10, 'Width' => 10, 'Height' => 3, 'Units' => 'IN')), '1' => array('Weight' => array('Value' => 5.0, 'Units' => 'LB'), 'Dimensions' => array('Length' => 20, 'Width' => 20, 'Height' => 10, 'Units' => 'IN'))); try { $response = $client ->getRates($request); if ($response -> HighestSeverity != 'FAILURE' && $response -> HighestSeverity != 'ERROR') { printRequestResponse($client); } else { echo 'Error in processing transaction.'. $newline. $newline; foreach ($response -> Notifications as $notification) { if(is_array($response -> Notifications)) { echo $notification -> Severity; echo ': '; echo $notification -> Message . $newline; } else { echo $notification . $newline; } } } writeToLog($client); // Write to log file } catch (SoapFault $exception) { printFault($exception, $client); } ?> I am not quite sure why it isn't working, i've read about using a proxy, but I am not quite sure how i would use it in this case? Isn't the point of using SOAP and WSDL to avoid using CURL, Direct Connect type stuff?

    Read the article

  • How to deal with OpenMP thread pool contention

    - by dpe82
    I'm working on an application that uses both coarse and fine grained multi-threading. That is, we manage scheduling of large work units on a pool of threads manually, and then within those work units certain functions utilize OpenMP for finer grain multithreading. We have realized gains by selectively using OpenMP in our costliest loops, but are concerned about creating contention for the OpenMP worker pool as we add OpenMP blocks to cheaper loops. Is there a way to signal to OpenMP that a block of code should use the pool if it is available, and if not it should process the loop serially?

    Read the article

  • How to change line thickness in iText?

    - by drasto
    I'm drawing images to pdf using Java framework iText. I need to draw lines of specified width. There is a method setLineWidth(float width) in class PdfContentByte that should change it. However no matter what value I pass as its parameter the lines drawn are always extra thin. There is following line in javadoc of setLineWidth: The line width specifies the thickness of the line used to stroke a path and is measured in user space units. I don't know what is "space unit". Everything else in iText seems to be measured in point(around 1/72 inch). I cant find any reference to what are those "space units" and how to change them. code: to.setLineWidth(thickness); to.moveTo(x, y); to.lineTo(x + 100, y + 100); Variable to contains instance of PdfContentByte.

    Read the article

  • JAVA Classes in Game programming.

    - by Gabriel A. Zorrilla
    I'm doing a little strategy game to help me learn Java in a fun way. The thing is I visioned the units as objects that would self draw on the game map (using images and buffering) and would react to the mouse actions with listeners attached to them. Now, based on some tutorials I've been reading regarding basic game programming, all seems to be drawn in the Graphics method of my Map class. If a new unit emerges, i just update the Map.Graphics method, it's not as easy as making a new Unit object which would self draw... In this case, I'd be stuck with a whole bunch of Map methods instead of using classes for rendering new things. So my question is, is it possible to use classes for rendering units, interface objects, etc, or i'll have to create methods and just do some kind of structural programming instead of object oriented? I'm a little bit confused and I'd like to have a mental blueprint of how things would be organized. Thanks!

    Read the article

  • annotation in matlab plot

    - by Tim
    Hi, I just wonder how to add annotation in matlab plot? Here is my code: plot(x,y); annotation('textarrow',[x, x+0.05],[y,y+0.05],'String','my point','FontSize',14); But the arrow points to the wrong place. How can I fix it? And any better idea for annotating a plot? Thanks and regards! EDIT: I just saw from the help document: annotation('line',x,y) creates a line annotation object that extends from the point defined by x(1),y(1) to the point defined by x(2),y(2), specified in normalized figure units. In my code, I would like the arrow pointing to the point (x,y) that is drawn by plot(), but annotation interprets the values of x and y as in normalized figure units. So I think that is what causes the problem. How can I specify the correct coordinates to annotation?

    Read the article

  • Setting image DPI in relation to height/width C#

    - by Aaron
    Hi, I'm writing an application to send some images to a third party, and the images must be 200x200 DPI. The image is a Bitmap and is sized at 500 width and 250 height. The first time I tested the images with the third party, my resolution was incorrect. I merely used image.SetResolution(200,200) to correctly set it to 200x200. This, however, only changed the resolution tag for the image and did not properly, according to my third party technical contact, adjust the image height and width. Is there a ratio that I can use so that for each X units I increment the resolution, I merely increment the corresponding height or width Y units? I thought that I could just increment resolution without having to increment height or width. Thank you, Aaron.

    Read the article

  • Pulling data from a text file to generate a report

    - by Edmond
    Have a program in Access, using VBA. I need to come up with an If statement to pull data from a text file. The data is a list of procedures and prices. I have to pull the prices from the text file to show in a report how much each procedure costs. ID PID M1 M2 M3 Total 1 11120390(procedure) 2 180(price) 360 180 540 1080(total Price) 3 2 1 3 6(Units sold) 4 5 200(Price) 200 600 800 1600(total price) 6 1 3 4 8(Units Sold) 7 11120390(procedure) The table in the text file is setup like this and I need to Pull the procedure number and the price of each procedure from the text file.

    Read the article

  • How do you change the subdocument location in a Word 2007 master document programmatically?

    - by boost
    We have had the unenviable happen: various master documents refer to sub-documents that are no longer where they used to be due to a directory renaming. Is there a programmatic way of tweaking the HYPERLINK field without losing the master/sub-document relationship? I've got this far ... Sub FixyaLinks() Dim s 'As String Dim i As Long Dim bTrackRevFlag As Boolean Dim bShowRevFlag As Boolean bTrackRevFlag = ActiveDocument.TrackRevisions bShowRevFlag = ActiveDocument.ShowRevisions ActiveDocument.TrackRevisions = False ActiveDocument.ShowRevisions = False For i = 1 To ActiveDocument.Fields.Count s = ActiveDocument.Fields.Item(i).Code.Text If InStr(s, "CURRICULUM\\NEW") Then s = Replace(s, "NEW Foundation Units-in developing", "Foundation Programme Units") ActiveDocument.Fields.Item(i).Code.Text = s End If Next ActiveDocument.TrackRevisions = bTrackRevFlag ActiveDocument.ShowRevisions = bShowRevFlag End Sub It bombs on ActiveDocument.Fields.Item(i).Code.Text = s, with an error 5686 ("The operation cannot be completed because the Track Changes option in the master document does not match the option the the subdocument. Make the Track Changes option the same in the master document and subdocument.") However, I'm not entirely sure what that means. Ideas anyone?

    Read the article

  • How to change line thickness in iText? (iText is Java pdf framework)

    - by drasto
    I'm drawing images to pdf using Java framework iText. I need to draw lines of specified width. There is a method setLineWidth(float width) in class PdfContentByte that should change it. However no matter what value I pass as its parameter the lines drawn are always extra thin. There is following line in javadoc of setLineWidth: The line width specifies the thickness of the line used to stroke a path and is measured in user space units. I don't know what is "space unit". Everything else in iText seems to be measured in point(around 1/72 inch). I cant find any reference to what are those "space units" and how to change them. code: to.setLineWidth(thickness); to.moveTo(x, y); to.lineTo(x + 100, y + 100);

    Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >