Search Results

Search found 10176 results on 408 pages for 'laptop cover'.

Page 122/408 | < Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >

• Intel Wireless 4965AGN not achieving N throughput when connected to an Airport Express N network

  - by BenA

  I have an Intel Wireless WiFi Link 4965AGN adaptor in my laptop (HP Pavillion dv2000 series) which is connecting to a 5Ghz-only 802.11n network provided by an Apple Airport Express. The network is using WPA2 encryption. My desktop is also connected the Airport, via a Linksys WUSB600N USB adaptor. Both are running with the latest drivers, and the Airport is running the latest firmware. The Airport is also configured to use wide channels. The problem I have is that I never get throughput above 4MB/s when transferring files between the two machines. Even a pessimistic calculation shows a 270Mbps network as being capable of transfer rates at well above 10MB/s. I'm pretty sure I've isolated the issue to being the Intel adaptor, as wiring the desktop to the AP, and using the Linksys adaptor on the laptop immediately yielded speeds limited by the 100MB/s ethernet connection. I know that 802.11n is still a draft standard, and so mixing kit from different manufacturers can easily lead to poor results, but I was just wondering if anybody else out there has had success with this Intel adaptor on an N network? Or even better, connecting it to an Airport Express? Can anybody give me any advice on how to troubleshoot this issue? I should also mention that the Airport Express doesn't allow you to manually specify channels when running in N mode, and that I've been able to rule out interference from other Wireless LANs by scanning. There aren't any other 5GHz networks in my area. All ideas welcome! Update: A while later, I've just updated to the most recent drivers for both the Intel chip in the laptop, and the USB adaptor. Unfortunately this hasn't improved things :(. If anybody has any advice it would be be gratefully received.

  Read the article

• Ubuntu/Nvidia lists DVI dual cable as single

  - by Joseph Mastey

  I have an NVidia Quadro FX 880M graphics card, from which I am trying to drive 2 monitors: my internal laptop montior (15.6", 1920x1080, Nvidia driver says it's running via DisplayPort) and an external 27" monitor (Dell U2711, 2560x1440 native resolution, via DVI). I've hooked the dual DVI cable to the dual DVI port on my dock (Dell PR03X) and installed the proprietary NVidia driver, but I cannot seem to get the full 2560x1440 out of the larger 27" external monitor. Looking at the NVidia driver settings, the monitor's connection is reported as a single DVI cable, rather than a dual one, which would explain the reduced resolution. Does anyone have any experience with an issue like this? What can I do to make full use of my new monitor? (Possibly) Relevant Information: There is no DVI port on the laptop itself, but one is provided via the dock. The laptop and dock both provide a DisplayPort jack, but I have been unable to get this working on either w/ the monitor. I did have the nouveau driver installed when I installed the nvidia proprietary driver, but have since removed it (no change in the monitor situation when I removed it). The 27" reports a max resolution of 1680x1050. Thanks, Joe

  Read the article

• First Request to IIS Express Fails with 503 Service Unavailable, Second Succeeds

  - by Chris Moschini

  Each time I start my ASP.Net MVC 3 app from Visual Studio 2010, IIS Express launches and IE spins waiting. The request fails with HTTP 503 Service Unavailable. I hit Refresh in IE, and the request succeeds. All subsequent requests succeed until I stop debugging. The next time I go to start debugging, the first request fails again. Has anyone else experienced this? In IISExpress\applicationhost.config I have: <site name="ProjectName" id="6"> <application path="/" applicationPool="Clr4IntegratedAppPool"> <virtualDirectory path="/" physicalPath="c:\users\chris\dropbox\code\2010\SolutionName\ProjectName" /> </application> <bindings> <binding protocol="http" bindingInformation="*:80:laptop" /> </bindings> </site> I have this in my hosts file: 127.0.0.1 laptop And my Project is set to start with IIS Express, with Project Url set to: http://laptop It's very strange that only the first request fails, perhaps as though Visual Studio isn't waiting long enough for IIS Express to start? Is there some way to make it wait? Stopping debugging, making a change, and then starting again is one of the most common tasks I do so adding another step to get there is pretty annoying.

  Read the article

• Lenovo Wi-Fi Replacement

  - by user22910

  I recently got my T500 with a very poor signal Wi-Fi, Thinkpad BGN, a Realtek chipset. I would like to replace my Wi-Fi card with either the Intel WiFi Link 5100 or 5300. However, I read somewhere that Lenovo specfically "whitelist" their Wi-Fi cards to only work with their laptops. I could not find any of the Intel Wi-Fi, moreover any Wi-Fi cards on the Lenovo site. So, I went to hunt around in Amazon and found several sellers. Plus what sort of card do I require? There is a difference between mini cards and the full sized card, though I do not know which one my laptop supports. Here are the specifications for my laptop: http://privatepaste.com/8b0537bce0 I would like to have confirmation which one of these specific cards as posted below will work on my laptop (or the one you recommend to have): Intel Wifi Link 5300 Intel WiFi Link 5100 - Network adapter - PCI Express Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft 2.0) Intel WiFi Link 5100 - Network adapter - PCI Express Half Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft) Intel WiFi Link 5300 - Network adapter - PCI Express Mini Card - 802.11b, 802.11a, 802.11g, 802.11n (draft)

  Read the article

• Why did MAC-Adress Cloning Fix My Router?

  - by FranticPedantic

  I have a Belkin router, and about a year ago, I suddenly lost my internet connectivity from Comcast. The internet worked fine when I plugged it right into my laptop, so I just ignored it. When I moved to another apartmnet I eventually took the dive and called tech support. The tech told me to clone my MAC address which completely fixed the issue. Now I know what a MAC address is and I've read what MAC cloning is. What has bothered me since is that I don't see how this fixed the issue. As I have understood MAC address cloning, it has the router pretend it has the same MAC address as my computer. Here is why I don't understand why this fixes my issue: I have used several different computers with this router. Cloning the MAC address fixed it for ALL of my computers. The laptop I first used with my ISP was not the one that I eventually had connected when I cloned the address. Furthermore, I didn't have any problems for quite some time after I stopped using the first computer. It wasn't like the internet suddenly stopped working when I changed which laptop I was using Now it occurred to me that maybe there was some sort of expiration? Except... Which MAC address did it clone? It was just an option in the router administration page. Did it just pick whichever computer was connected to it? If my ISP still wanted the MAC of my first computer, how did some other computer's fix it? As mentioned earlier, why did this problem seemingly stem from nowhere? Anyway, I don't have any current problems so this is more just out of general curiosity. If anybody can explain it, it would be appreciated!

  Read the article

• How to update the hard disk device drivers for a ghosted hard drive image so it can run on different hardware: Ultra ATA > SATA

  - by rism

  I've ghosted a Winxp machine from one laptop with Ultra ATA drive, and would like to set it up on another laptop as a multiboot option on another hard driver with a SATA drive. I can install the partition fine but if i make it active and try to boot it it blue screens. The blue screen is so fast i cant even read it, other than to make out it's saying "something", im picking probably hard drive as it goes through POST fine. So basically i would like to boot into my Win7 OS, and then somehow manipulate the XP partition to use updated drivers for the new hard drive/laptop so that i can then at least boot into the XP OS on the new machine and update all the other drivers in safe mode or whatever to get it to run. I assume someone is going to tell me to just do a fresh install, but that kinda defeats the purpose of ghosting at this point. There is a significant amount of personalisation, development setup on the XP machine that i would like to just transfer as is. As it stands ive invested minmal time in getting it to run, just a ghost and recovery and then a blue screen boot or two, so its still well worth it to me, time wise to try this way. Thanks.

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Play audio over network with Windows 7?

  - by Josh

  I have a unique situation where I'd like to stream audio (ALL audio, not just mp3s, etc) from my laptop to another computer over the network. I live in a studio apartment and my laptop is my main computer but I'd like it's audio to play on my htpc with a nice stereo system. Since it's a studio, both computers are in the same room so I don't want 2 sets of speakers. I want my computer to directly play back through the stereo. I used to do this with pulseaudio but my job now requires that I run Windows full time. I'm aware of Shoutcast and other similar streaming solutions but I don't want any transcoding done. It's a waste of CPU and not to mention my laptop fans, and I don't mind the network bandwidth that uncompressed audio requires. Is there a way to run Shoutcast without encoding? Also, I know that Windows Remote Desktop can play audio over the network pretty easily. Is this part of .Net that I could just code a simple app that streams the audio without RD'ing in? I also don't want to run it over a physical wire. :)

  Read the article

• Get details / solve issue with a kernel panic?

  - by Joseph

  I have a Lenovo T430 running Linux Mint 13 (MATE): joseph:~$ uname -a Linux joseph-T430-LM 3.2.0-23-generic #36-Ubuntu SMP Tue Apr 10 20:39:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I installed Mint immediately after getting the laptop about two weeks ago, and have noticed that about once a day, the computer will completely freeze up- I can't use Ctrl+Alt+Backspace to restart X, I can't use Ctrl+Alt+F1 to get a text only terminal, can't move mouse, can't type, and if any music was playing it just gets stuck in about a 1-second loop. There is a Windows partition, but I haven't had any issues in Windows. I couldn't find a common thread between the freezes, they were seemingly random (sometimes right after I clicked the mouse, sometimes not; sometimes with Pandora/flash being used, sometimes not, etc). I assume they're kernel panics since it completely locks up, but the laptop doesn't have a capslock or scroll lock LED. It is on a dock and I do have a USB keyboard, but the scroll lock/capslock lights do not flash when it happens (not sure if this is indicating its not a kernel panic, or if the kernel panic just wouldn't illuminate the LEDs on a usb keyboard attached to a laptop dock). This was annoying but not terrible. However, I've found a way to reproduce it. I have a particular CSV file that when I open up in LibreOffice Calc and scroll around, the same thing happens- complete lock up. I really need to use this file, so I'd like to fix the issue, but at the least it's given me a test case to work with. So, having a case where I can cause this issue, what can I do to better find out what's going on? I've looked in /var/log/syslog but haven't found anything seemingly useful. Any thoughts?

  Read the article

• what's the difference between a Volume and a Partition in Windows 7 diskpart

  - by user170232

  I was trying to follow the Intel guide for setting up iRST (Intel Rapid Start Technology) on my new laptop. The Intel manual says you need to create a *Volume that is as big or bigger than your available memory, set it to a specific id (id=84), then go into the iRST tool and adjust some settings. Looking at the disk manager on the laptop, I see there is already a Partition labeled as "Hibernation Partition" which is a little bigger than the memory in my system. So it looks like iRST was already set up...BUT, it's a Partition, not a Volume. Here's what the manual says to do: (from: http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide.pdf) diskpart list disk select disk x (where x is the disk to use, there's only one disk in this laptop) create partition primary size=X000 (where X000 is the size to create) detail disk (which lists details for the disk. This is where i get hung up) select volume Z (where Z is the *partition you created previously) ** it says the 'detail disk' command will list the volume #, but it doesn't. ** 'detail disk' only lists two "volumes" for Recovery and OS. ** if i do 'list partition', i see the 8 GB *partition labeled as "Hibernation Partition") ** so I can't continue with the following steps: set id=84 override exit The reason I went looking for the manual is because when iRST is enabled in the BIOS, the system won't resume from sleep. When it's disabled, it works fine, but the system goes into (legacy?) Hibernation mode and takes a while to come out of Hibernation. the iRST is supposed to resume from deep sleep very quickly. So, what's the difference between a Volume and a Partition? Should I delete the Hibernation Partition and create a Hibernation Volume? Anyone have any ideas? (if it matters, this is on a Dell XPS 13 with BIOS A08) Thanks! J

  Read the article

• Boot loop that I cannot bypass

  - by lonewaft

  Recently, on a laptop that I've used for a while, I had a strange issue where OS files were corrupted (device manager) and Windows 8 was hung after the login screen, so I reinstalled Windows 7 over the existing Windows 8 installation, and it worked for a couple days. Today, when I tried to use my laptop, it was stuck on a boot loop. Right after the BIOS screen, it would show a flashing underscore, then restart the computer, again and again until I removed the battery. I tried booting to a windows 7 install CD, but the same flashing underscore - reboot sequence happened when I tried. I tried moving the boot priority around (HDD first, CD/DVD first, even USB first) but nothing changed. After about an hour of tinkering with it, I listened to the HDD sounds, and it sounded like the HDD was trying to spin up, but failing (whining noise increasing in frequency that stopped and started in sync with the system restarting). I am planning to replace the HDD, but I'm still confused as to why a faulty HDD would stop the laptop from booting to my install DVD (tried it on a different computer, it booted from that CD fine). Anybody here have any idea why this might be happening?

  Read the article

• Dell Inspiron 1564 overheating but fan not switching on, how to diagnose?

  - by Smugrik

  I've got a Dell Inspiron 1564 laptop that is about one and a half years old. Since about a week, the laptop started to overheat, causing it to switch off unexpectedly... The cpu fan is working erratically, it can start to spin for a while, doing its job and cooling down the cpu before it stops, but then the temperature goes up, and the fan doesn't reacts, once the temperature reaches a critical point (over 85 celsius, checked with speedfan...), the laptop switches off... I already cleaned the vents and fan from dust, to no avail, and it was actually quite clean anyway. Drivers and bios are up-to-date, no crapware was ever installed on this machine. I don't know how to diagnose the problem, could it be the temperature sensors that sends wrong information, so the fan doesn't reacts? but then I believe the computer wouldn't detect the overheat and stop... Is there a way I can pin point the problem? Maybe some low-level diagnostic tools to check functionality of sensors and fans??? The warranty is already over so any suggestion would be welcome. Thanks!!

  Read the article

• Mac OS X Client With Static DHCP Assignment Requests Wrong IP via Option 50

  - by Starchy

  I have a number of Mac (and a few Linux) laptops getting DHCP from a Force10 layer 3 switch, the only DHCP server on the subnet. There's a global dynamic pool, and for each full-time employee's laptop I have a single IP static pool set by MAC address. One and only one of the clients, running OS X 10.7.5, consistently fails to get a static assignment. The MAC address in the static pool definition has been carefully re-checked. Running tcpdump on a mirrored port when the laptop connects, I see that it is specifically requesting 10.100.0.252 (a dynamic address): 11:32:10.108280 IP (tos 0x0, ttl 255, id 28293, offset 0, flags [none], proto UDP (17), length 328) 0.0.0.0.bootpc > broadcasthost.bootps: [udp sum ok] BOOTP/DHCP, Request from 3c:07:54:xx:xx:xx (oui Unknown), length 300, xid 0x1399da89, Flags [none] (0x0000) Client-Ethernet-Address 3c:07:54:xx:xx:xx (oui Unknown) Vendor-rfc1048 Extensions Magic Cookie 0x63825363 DHCP-Message Option 53, length 1: Request Parameter-Request Option 55, length 9: Subnet-Mask, Default-Gateway, Domain-Name-Server, Domain-Name Option 119, LDAP, Option 252, Netbios-Name-Server Netbios-Node MSZ Option 57, length 2: 1500 Client-ID Option 61, length 7: ether 3c:07:54:xx:xx:xx Requested-IP Option 50, length 4: 10.100.0.252 Lease-Time Option 51, length 4: 7776000 Hostname Option 12, length 10: "host-name" END Option 255, length 0 PAD Option 0, length 0, occurs 8 I haven't been able to find any extra system prefs or unusual software on the laptop. Disabling the interface and rebooting or temporarily setting the IP manually both fail to make any difference. Any suggestions appreciated.

  Read the article

• can't ssh within LAN, but can connect from outside

  - by Patrick B.

  A strange issue: I have a desktop running Ubuntu 10.04 behind a Netgear WNR1000 router performing NAT. I would like to be able to ssh into the desktop from my laptop (running Windows 7 and Cygwin). When at home, both the desktop and the laptop are connected by wireless (the desktop is in a different room from the router). sshd seems to be running fine, since ssh localhost from the desktop works without trouble. Also, ssh my.ip.address from my laptop when it is not behind the router works fine (I am forwarding port 22 on the router to my desktop). However, ssh same.ip.address from within the LAN fails with "Connection refused". ssh 192.168.local.ip.address fails with a different message, "Connection timed out". I can connect if I first ssh to a machine outside the LAN. So far I haven't found anything with Google because with the search terms that seem like they would be relevant, the vast majority of people have the opposite problem - i.e., they can't connect from outside the LAN but can connect within it. I can port forward through a remote server when I'm at home, but this seems like a totally absurd way to connect two computers on the same home LAN. I have already tried stopping and starting sshd on the desktop. Any thoughts?

  Read the article

• Bugzilla email issue

  - by xian

  My bugzilla system keep hit the following error: There was an error sending mail from '[email protected]' to '[email protected]':Can't send data I think that is some problem with my setting and configuration. First is the urlbase I have tried setting it to bugzilla.example.com, and http://127.0.0.1:81/, and http://10.0.0.236/ (My laptop IP address, I use this laptop to set up bugzilla) but the error still persists. Actually what should I put in the urlbase field? Parameter = Email Under mail_delivery_method, i choose SMTP. Under mailfrom, I put bugzilla-daemon. smtpserver, I tried leaving it blank, or setting it to 220.181.12.12 before, but could not solve my problem For my sql, the following is the data and command I used: C:\mysql\bin>mysql --user=root -p mysql Enter password: 1234 (When I install mysql into my laptop, it ask me to key an username and password, i have key in username as 'cvuser' and password as '1234', but here never ask me to key in any username) Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1 Server version: 5.5.15 MySQL Community Server (GPL) mysql> GRANT ALL PRIVILEGES ON bugs.* TO 'bugs'@'localhost' IDENTIFIED BY '123456'; Query OK, 0 rows affected (0.03 sec) In C:\Bugzilla\localconfig, I put the following info: # # How to access the SQL database: # $db_host = "localhost"; # where is the database? $db_port = 3306; # which port to use $db_name = "bugs"; # name of the MySQL database $db_user = "bugs"; # user to attach to the MySQL database # # Enter your database password here. It's normally advisable to specify # a password for your bugzilla database user. # If you use apostrophe (') or a backslash (\) in your password, you'll # need to escape it by preceding it with a \ character. (\') or (\\) # $db_pass = '123456'; Can someone tell me where my mistake is? I have googled for this issue for few days but still cannot find the solution.

  Read the article

• What is the latest on Microsoft Expression Studio licensing?

  - by DanM

  In the past, there's been an issue with Microsoft not allowing you to deactivate an Expression Studio key. Basically, you get two keys per license. If you assign both keys (say one to a desktop and one to a laptop), then you upgrade to a new machine (say you replace your laptop or upgrade some of the hardware), you have to buy a new copy of Expression Studio ($600 for Ultimate). This seems ludicrous to me, and I'm wondering if anyone knows if this policy is still in place. I can't seem to find a EULA online anywhere, so I don't know where to find this information. I know my laptop is due for replacement soon, and I want to know if I'm going to have to sink $600 into a software product I already purchased. For background, please refer to this thread on the Microsoft Expression forums: http://social.expression.microsoft.com/Forums/en-US/general/thread/da5587bc-b098-4c6a-9a56-af3608d940d0 Note that this thread is locked. Microsoft doesn't seem to want people to discuss this. This is one reason I'm posting here rather than on that site.

  Read the article

• Prevent Roaming profiles from syncing certain elements

  - by user29919

  Hello everyone, I'm somewhat new to the Server 2008 front, and I'm afraid I've hit my first snag: I've set up roaming profiles, and they appear to be working too well. Is there a way to limit, ideally on a folder/object basis, what gets synced with a roaming profile? What I'm trying to do is: 1) stop my roaming profile from syncing desktop layout - I run a dual-screen desktop and a laptop, and it's really annoying to have to reposition everything after logging onto the laptop, because it forces everything onto one screen. 2) stop it from syncing registry variables - specifically, I want Visual Studio to load different setting files on each computer. Currently, the variable that contains that path is getting synced whenever I log in, so I get the settings from whatever box I last logged out from. 3) stop syncing the start menu - this one's not as big, but I'm noticing 'program not found' icons even for programs that are installed. they work when I click them - they just look ugly. I'm running Windows SBS 2008 x64 with two Win7 clients (x86 Pro, and X64 Ultimate). Is there a simple way to do that? Or am I trying to work too much against what roaming profiles are designed for? I could, of course, set up different profiles for the desktop and laptop, but that seems to defeat the point of roaming profiles entirely... Thanks in advance! Any help will be much appreciated =)

  Read the article

• Windows XP dual screen problems, user account related

  - by Chris

  I have had this issue with a few laptops now and it looks like it is some sort of user account problem. Specifics of the system are: Dell Laptop Windows XP Pro SP3 Non-domain member computer DLP Projector connected to laptop via VGA I use this setup almost daily to do presentations, always the mirrored display mode where I can see on the laptop monitor the same thing that is displayed on the projector. Today, when I boot up, I get the mirrored display at the login screen, but after I log in, it switches to Extended Desktop (like two desktops side-by-side). Fn+F8 just cycles through all the normal settings except the mirrored display. I created a new user account on the computer and it performs normally. Mirrored display works as normal. I have run into this about 4 times now and it always can be solved by creating a new user account on the computer, and then all is well. I would like to either: 1. Find a way to reset the customized settings for a specific user account which would hopefully make this go away, or 2. Find the specific setting that causes this so that I can easily fix it when the problem comes up. Creating new user accounts is kind of a pain and a easy fix must be out there somewhere.

  Read the article

• Problem setting up HP PhotoSmart C4783

  - by ProfKaos

  I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

  Read the article

• Some URLs fail to load on Windows web portal

  - by jpolache

  I’m working in a large data center and have been assigned to troubleshoot and issue with a windows (IIS) web server that acts as a portal for a customer of the data center. This portal server is on a DMZ at the local data center. I don’t have access to the portal desktop and am relying on an off-site administrator to work with me to do testing and report the condition of the portal. He tells me there are no software firewalls or other filtering configured. While most of the remote web pages work fine, several of the URSs the portal is suppose to serve up fail to load. I had wireshark installed on the portal system and had a capture taken of one of the failures. I used IE to access one of the remote web servers at issue. I could see the TCP SYN-ACK coming back from the remote server, but after several HTTP GETs fail to get a response the portal server sends a reset. The webmaster of the remote web server assures me that no sites are being blocked. I had a capture taken outside the local firewall, so there should be no issue there. Another tech set up a laptop and used the IP address of the portal (we took the portal off-line for the test). The laptop loads the URL as expected. I tried having Firefox loaded to make sure that the HTTP GET was not mal-formed. Same failure as with IE. So, it seems it is not the remote web server or the network, because there was no problem with the laptop. At this point, I’m not sure what other questions to ask or tests to do.

  Read the article

• OpenVPN bad source address from client

  - by Bogdan

  I have one problem with OpenVPN. There are a lot drops records in the openvpn log file on the server: Mon Oct 22 10:14:41 2012 us=726541 laptop/???:1194 MULTI: bad source address from client [192.168.1.107], packet dropped grep -E "^[a-z]" server.conf ----- port 1194 proto udp dev tun ca data/ca.crt cert data/server.crt key data/server.key dh data/dh1024.pem tls-server tls-auth data/ta.key 0 remote-cert-tls client cipher AES-256-CBC tun-mtu 1200 server 10.10.10.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" client-to-client client-config-dir /etc/openvpn/ccd route 10.10.10.0 255.255.255.0 keepalive 10 120 comp-lzo persist-key persist-tun max-clients 5 status /var/log/status-openvpn.log log /var/log/openvpn.log verb 4 auth-user-pass-verify /etc/openvpn/verify.sh via-file tmp-dir /tmp script-security 2 ----- cat ccd/laptop ----- iroute 10.10.10.0 255.255.255.0 ----- cat client.conf ----- remote server ip 1194 client dev tun ping 10 comp-lzo proto udp tls-client tls-auth data/ta.key 1 pkcs12 data/vpn.laptop.p12 remote-cert-tls server #ns-cert-type server persist-key persist-tun cipher AES-256-CBC verb 3 pull auth-user-pass /home/user/.openvpn/users.db ----- According to "Jan Just Keijser - OpenVPN 2 Cookbook" root of the problem is incorrect config options.see the screenshot But, as you see, my config has such options. Could you please help me to solve this problem. @week Verb leverl=6; client log. Mon Oct 22 16:06:02 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Mon Oct 22 16:06:02 2012 /sbin/ifconfig tun0 10.10.10.3 pointopoint 10.10.10.5 mtu 1500 Mon Oct 22 16:06:02 2012 /sbin/route add -net xxxx netmask 255.255.255.255 gw 192.168.1.1 Mon Oct 22 16:06:02 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 Initialization Sequence Completed cat ccd/latop iroute 10.10.10.0 255.255.255.0 ifconfig-push 10.10.10.3 10.10.10.5

  Read the article

• MediaWiki migrated from Tiger to Snow Leopard throwing an exceptions

  - by Matt S

  I had an old laptop running Mac OS X 10.4 with macports for web development: Apache 2, PHP 5.3.2, Mysql 5, etc. I got a new laptop running Mac OS X 10.6 and installed macports. I installed the same web development apps: Apache 2, PHP 5.3.2, Mysql 5, etc. All versions the same as my old laptop. A Mediawiki site (version 1.15) was copied over from my old system (via the Migration Assistant). Having a fresh Mysql setup, I dumped my old database and imported it on the new system. When I try to browse to mediawiki's "Special" pages, I get the following exception thrown: Invalid language code requested Backtrace: #0 /languages/Language.php(2539): Language::loadLocalisation(NULL) #1 /includes/MessageCache.php(846): Language::getFallbackFor(NULL) #2 /includes/MessageCache.php(821): MessageCache->processMessagesArray(Array, NULL) #3 /includes/GlobalFunctions.php(2901): MessageCache->loadMessagesFile('/Users/matt/Sit...', false) #4 /extensions/OpenID/OpenID.setup.php(181): wfLoadExtensionMessages('OpenID') #5 [internal function]: OpenIDLocalizedPageName(Array, 'en') #6 /includes/Hooks.php(117): call_user_func_array('OpenIDLocalized...', Array) #7 /languages/Language.php(1851): wfRunHooks('LanguageGetSpec...', Array) #8 /includes/SpecialPage.php(240): Language->getSpecialPageAliases() #9 /includes/SpecialPage.php(262): SpecialPage::initAliasList() #10 /includes/SpecialPage.php(406): SpecialPage::resolveAlias('UserLogin') #11 /includes/SpecialPage.php(507): SpecialPage::getPageByAlias('UserLogin') #12 /includes/Wiki.php(229): SpecialPage::executePath(Object(Title)) #13 /includes/Wiki.php(59): MediaWiki->initializeSpecialCases(Object(Title), Object(OutputPage), Object(WebRequest)) #14 /index.php(116): MediaWiki->initialize(Object(Title), NULL, Object(OutputPage), Object(User), Object(WebRequest)) #15 {main} I tried to step through Mediawiki's code, but it's a mess. There are global variables everywhere. If I change the code slightly to get around the exception, the page comes up blank and there are no errors (implying there are multiple problems). Anyone else get Mediawiki 1.15 working on OS X 10.6 with macports? Anything in the migration from Tiger that could cause a problem? Any clues where to look for answers?

  Read the article

• Need Suggestions on Backup Strategies and Alternatives?

  - by Leejo

  I'm not sure where else to post this question since it is not exactly Code or Development related...but I know Stackoverflow is a very responsive to questions... Currently, I use Mozy Home to perform an online backup of my laptop. So far, this works well, since I only use one laptop that needs to be backed up. But, soon this may change and I want to explore other alternatives than having to perform an online backup on all machines. Ideally, I want to set up a Network Computer (Laptop/Desktop) with enough storage to hold the backups for all other machines that I would have. Each machine should be responsible for performing their backup (to the Network Computer). This would require some capability like Mozy's incremental backup strategy, but instead of online backup, I would prefer it to be done locally to the Network Computer. Can you recommend a local backup software (backup to a network pc, incremental backup, good restore options)? I'm also looking for any ideas on a local backup strategy even if its different from what I've stated? What works and what doesn't work? Thanks in advance for your help!

  Read the article

• Firefox 29 - how do I delete history entries visited fewer than x times

  - by lousyuser

  Context: I've been using my Firefox profile for a couple of years now. My history file has become huge, naturally. I got Firefox Sync set up between my main desktop PC and my laptop. HW configs: PC: i5-3450, 8 GB DDR3 RAM, Crucial M4 128 GB SSD laptop: Pentium SU4100, 4 GB DDR3 RAM, WD 5400 rpm HDD Accessing history entries when typing into the Awesome Bar on my desktop takes quite a long time despite the decent config, the laptop is even slower. The experience is quite unresponsive. I figured if I cleared the history up a little bit, I might avoid creating a new profile to speed things up. The question itself: to illustrate: Is there a way to delete all history entries that have been visited fewer than x (let's say 5) times and at the same time the recent visit is fewer than y (let's say 120) days old? afaik the history file is some kind of SQL database, but I'm not really sure how the data is saved, if there's a "safe way" to edit it and what the query to do what I need would look like. Thanks in advance for any help. I kept browsing through previous SuperUser questions to see if I could find relevant information. "In my Firefox profile directory, there is a filed named places.sqlite. Opening it with sqlite reveals (amongst others) the tables moz_places and moz_historyvisits. It seems that moz_historyvisits uses the primary of moz_places to refer to the URLs." As I'm unfamiliar with databases, I don't really understand the way the two tables mentioned in the quote are related. screenshot of a part of the tables I've noticed the visit_count is in a standard format, making it easy to work with. The last_visit_date looks encrypted to my naked eye, but I can't see in which way. Hope that helps, I'm at my wits' end.

  Read the article

• server and user directly connected no pinging...

  - by jtzero

  I have a server(fedora 12) with two nics on it, directly connected to say 192.168.1.0 and 192.168.2.0 the route table looks like this Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 192.168.1.1 255.255.255.0 U 0 0 0 eth0 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 eth0 = 192.168.1.15 eth1 = 192.168.2.1 and a directly connected user (Mythdora) on the 192.168.2.0 network with ip 192.168.2.2 and route table like so Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 0 0 0 eth0 the cable is a crossover and it works all three nics work -- connected my laptop to either end and assign it a valid 192.168.2.0 ip the pings will work. In fact if I disconnect the server side and plug the eth cable into the laptop and have thte box ping the laptop continually remove the eth cable and plug it back into the server both sides ping... unfortunately the box realizing it's connected to a different pc wipes its route table after say ten minutes or so. if I do a trace route from a box on the 1.0 network to the servers 192.168.2.1 interface never get a reply from it. as a note at one point I could ping the server from the 192.168.2.2 box but the server couldnt ping the 192.168.2.2 box.

  Read the article

< Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >