Search Results

Search found 17407 results on 697 pages for 'static constructor'.

Page 122/697 | < Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• What's up with stat on Macos/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Macos 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputing the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• What's up with stat on Mac OS X/Darwin? Or filesystems without names...

  - by Charles Stewart

  In response to a question I asked on SO, Give the mount point of a path, one respondant suggested using stat to get the device name associated with the volume of a given path. This works nicely on Linux, but gives crazy results on Mac OS X 10.4. For my system, df and mount give: cas cas$ df Filesystem 512-blocks Used Avail Capacity Mounted on /dev/disk0s3 58342896 49924456 7906440 86% / devfs 194 194 0 100% /dev fdesc 2 2 0 100% /dev <volfs> 1024 1024 0 100% /.vol automount -nsl [166] 0 0 0 100% /Network automount -fstab [170] 0 0 0 100% /automount/Servers automount -static [170] 0 0 0 100% /automount/static /dev/disk2s1 163577856 23225520 140352336 14% /Volumes/Snapshot /dev/disk2s2 409404102 5745938 383187960 1% /Volumes/Sparse cas cas$ mount /dev/disk0s3 on / (local, journaled) devfs on /dev (local) fdesc on /dev (union) <volfs> on /.vol automount -nsl [166] on /Network (automounted) automount -fstab [170] on /automount/Servers (automounted) automount -static [170] on /automount/static (automounted) /dev/disk2s1 on /Volumes/Snapshot (local, nodev, nosuid, journaled) /dev/disk2s2 on /Volumes/Sparse (asynchronous, local, nodev, nosuid) Trying to get the devices from the mount points, though: cas cas$ df | grep -e/ | awk '{print $NF}' | while read line; do echo $line $(stat -f"%Sdr" $line); done / disk0s3r /dev ???r /dev ???r /.vol ???r /Network ???r /automount/Servers ???r /automount/static ???r /Volumes/Snapshot disk2s1r /Volumes/Sparse disk2s2r Here, I'm feeding each of the mount points scraped from df to stat, outputting the results of the "%Sdr" format string, which is supposed to be the device name: Cf. stat(1) man page: The special output specifier S may be used to indicate that the output, if applicable, should be in string format. May be used in combination with: ... dr Display actual device name. What's going on? Is it a bug in stat, or some Darwin VFS weirdness? Postscript Per Andrew McGregor, try passing "%Sd" to stat for more weirdness. It lists some apparently arbitrary subset of files from CWD...

  Read the article

• Is it worthwhile to block malicious crawlers via iptables?

  - by EarthMind

  I periodically check my server logs and I notice a lot of crawlers search for the location of phpmyadmin, zencart, roundcube, administrator sections and other sensitive data. Then there are also crawlers under the name "Morfeus Fucking Scanner" or "Morfeus Strikes Again" searching for vulnerabilities in my PHP scripts and crawlers that perform strange (XSS?) GET requests such as: GET /static/)self.html(selector?jQuery( GET /static/]||!jQuery.support.htmlSerialize&&[1, GET /static/);display=elem.css( GET /static/.*. GET /static/);jQuery.removeData(elem, Until now I've always been storing these IPs manually to block them using iptables. But as these requests are only performed a maximum number of times from the same IP, I'm having my doubts if it does provide any advantage security related by blocking them. I'd like to know if it does anyone any good to block these crawlers in the firewall, and if so if there's a (not too complex) way of doing this automatically. And if it's wasted effort, maybe because these requests come from from new IPs after a while, if anyone can elaborate on this and maybe provide suggestion for more efficient ways of denying/restricting malicious crawler access. FYI: I'm also already blocking w00tw00t.at.ISC.SANS.DFind:) crawls using these instructions: http://spamcleaner.org/en/misc/w00tw00t.html

  Read the article

• Some Original Expressions

  - by Phil Factor

  Guest Editorial for Simple-Talk newsletterIn a guest editorial for the Simple-Talk Newsletter, Phil Factor wonders if we are still likely to find some more novel and unexpected ways of using the newer features of Transact SQL: or maybe in some features that have always been there! There can be a great deal of fun to be had in trying out recent features of SQL Expressions to see if  they provide new functionality.  It is surprisingly rare to find things that couldn’t be done before, but in a different   and more cumbersome way; but it is great to experiment or to read of someone else making that discovery.  One such recent feature is the ‘table value constructor’, or ‘VALUES constructor’, that managed to get into SQL Server 2008 from Standard SQL.  This allows you to create derived tables of up to 1000 rows neatly within select statements that consist of  lists of row values.  E.g. SELECT Old_Welsh, number FROM (VALUES ('Un',1),('Dou',2),('Tri',3),('Petuar',4),('Pimp',5),('Chwech',6),('Seith',7),('Wyth',8),('Nau',9),('Dec',10)) AS WelshWordsToTen (Old_Welsh, number) These values can be expressions that return single values, including, surprisingly, subqueries. You can use this device to create views, or in the USING clause of a MERGE statement. Joe Celko covered  this here and here.  It can become extraordinarily handy to use once one gets into the way of thinking in these terms, and I’ve rewritten a lot of routines to use the constructor, but the old way of using UNION can be used the same way, but is a little slower and more long-winded. The use of scalar SQL subqueries as an expression in a VALUES constructor, and then applied to a MERGE, has got me thinking. It looks very clever, but what use could one put it to? I haven’t seen anything yet that couldn’t be done almost as  simply in SQL Server 2000, but I’m hopeful that someone will come up with a way of solving a tricky problem, just in the same way that a freak of the XML syntax forever made the in-line  production of delimited lists from an expression easy, or that a weird XML pirouette could do an elegant  pivot-table rotation. It is in this sort of experimentation where the community of users can make a real contribution. The dissemination of techniques such as the Number, or Tally table, or the unconventional ways that the UPDATE statement can be used, has been rapid due to articles and blogs. However, there is plenty to be done to explore some of the less obvious features of Transact SQL. Even some of the features introduced into SQL Server 2000 are hardly well-known. Certain operations on data are still awkward to perform in Transact SQL, but we mustn’t, I think, be too ready to state that certain things can only be done in the application layer, or using a CLR routine. With the vast array of features in the product, and with the tools that surround it, I feel that there is generally a way of getting tricky things done. Or should we just stick to our lasts and push anything difficult out into procedural code? I’d love to know your views.

  Read the article

• vSphere ESX 5.5 hosts cannot connect to NFS Server

  - by Gerald

  Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

  Read the article

• Clipping polygons in XNA with stencil (not using spritebatch)

  - by Blau

  The problem... i'm drawing polygons, in this case boxes, and i want clip children polygons with its parent's client area. // Class Region public void Render(GraphicsDevice Device, Camera Camera) { int StencilLevel = 0; Device.Clear( ClearOptions.Stencil, Vector4.Zero, 0, StencilLevel ); Render( Device, Camera, StencilLevel ); } private void Render(GraphicsDevice Device, Camera Camera, int StencilLevel) { Device.SamplerStates[0] = this.SamplerState; Device.Textures[0] = this.Texture; Device.RasterizerState = RasterizerState.CullNone; Device.BlendState = BlendState.AlphaBlend; Device.DepthStencilState = DepthStencilState.Default; Effect.Prepare(this, Camera ); Device.DepthStencilState = GlobalContext.GraphicsStates.IncMask; Device.ReferenceStencil = StencilLevel; foreach ( EffectPass pass in Effect.Techniques[Technique].Passes ) { pass.Apply( ); Device.DrawUserIndexedPrimitives<VertexPositionColorTexture>( PrimitiveType.TriangleList, VertexData, 0, VertexData.Length, IndexData, 0, PrimitiveCount ); } foreach ( Region child in ChildrenRegions ) { child.Render( Device, Camera, StencilLevel + 1 ); } Effect.Prepare( this, Camera ); // This does not works Device.BlendState = GlobalContext.GraphicsStates.NoWriteColor; Device.DepthStencilState = GlobalContext.GraphicsStates.DecMask; Device.ReferenceStencil = StencilLevel; // This should be +1, but in that case the last drrawed is blue and overlap all foreach ( EffectPass pass in Effect.Techniques[Technique].Passes ) { pass.Apply( ); Device.DrawUserIndexedPrimitives<VertexPositionColorTexture>( PrimitiveType.TriangleList, VertexData, 0, VertexData.Length, IndexData, 0, PrimitiveCount ); } } public static class GraphicsStates { public static BlendState NoWriteColor = new BlendState( ) { ColorSourceBlend = Blend.One, AlphaSourceBlend = Blend.One, ColorDestinationBlend = Blend.InverseSourceAlpha, AlphaDestinationBlend = Blend.InverseSourceAlpha, ColorWriteChannels1 = ColorWriteChannels.None }; public static DepthStencilState IncMask = new DepthStencilState( ) { StencilEnable = true, StencilFunction = CompareFunction.Equal, StencilPass = StencilOperation.IncrementSaturation, }; public static DepthStencilState DecMask = new DepthStencilState( ) { StencilEnable = true, StencilFunction = CompareFunction.Equal, StencilPass = StencilOperation.DecrementSaturation, }; } How can achieve this? EDIT: I've just relized that the NoWriteColors.ColorWriteChannels1 should be NoWriteColors.ColorWriteChannels. :) Now it's clipping right. Any other approach?

  Read the article

• Adding operation in middle of complex sequence diagram in visio 2003

  - by James

  I am using Microsoft Visio 2003 to define static classes with operations/methods and a sequence diagrams referring to these classes. The sequence diagram is almost done, but i realized that i missed one operation in middle of the diagram. When i try to move rest of the sequences down by selecting it as a block, all the operations in the block loose link with static diagrams. ( Methods which were referred to static classes as fun(), became fun, which means that now they no longer refer to static diagrams and any future changes would not be reflected in dynamic sequence diagrams automatically.) The sequence diagrams have grown to A3 size paper and i have many of such diagrams which needs correction. Manually moving the operations one by one would involve lots of effort. Could someone kindly suggest a way to overcome this problem?

  Read the article

• RPi and Java Embedded GPIO: Using Java to read input

  - by hinkmond

  Now that we've learned about using Java code to control the output of the Raspberry Pi GPIO ports (by lighting up LEDs from a Java app on the RPi for now and noting in the future the same Java code can be used to drive industrial automation or medical equipment, etc.), let's move on to learn about reading input from the RPi GPIO using Java code. As before, we need to start out with the necessary hardware. For this exercise we will connect a Static Electricity Detector to the RPi GPIO port and read the value of that sensor using Java code. The circuit we'll use is from William J. Beaty and is described at this Web link. See: Static Electricity Detector He calls it an "Electric Charge" detector, which is a bit misleading. A Field Effect Transistor is subject to nearby electro-magnetic fields, such as a static charge on a nearby object, not really an electric charge. So, this sensor will detect static electricity (or ghosts if you are into paranormal activity ). Take a look at the circuit and in the next blog posts we'll step through how to connect it to the GPIO port of your RPi and then how to write Java code to access this fun sensor. Hinkmond

  Read the article

• Design guideline for saving big byte stream in c# [migrated]

  - by Praveen

  I have an application where I am receiving big byte array very fast around per 50 miliseconds. The byte array contains some information like file name etc. The data (byte array ) may come from several sources. Each time I receive the data, I have to find the file name and save the data to that file name. I need some guide lines to how should I design it so that it works efficient. Following is my code... public class DataSaver { private static Dictionary<string, FileStream> _dictFileStream; public static void SaveData(byte[] byteArray) { string fileName = GetFileNameFromArray(byteArray); FileStream fs = GetFileStream(fileName); fs.Write(byteArray, 0, byteArray.Length); } private static FileStream GetFileStream(string fileName) { FileStream fs; bool hasStream = _dictFileStream.TryGetValue(fileName, out fs); if (!hasStream) { fs = new FileStream(fileName, FileMode.Append); _dictFileStream.Add(fileName, fs); } return fs; } public static void CloseSaver() { foreach (var key in _dictFileStream.Keys) { _dictFileStream[key].Close(); } } } How can I improve this code ? I need to create a thread maybe to do the saving.

  Read the article

• Sharing internet connection from Windows XP using wi-fi router

  - by Darius

  Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

  Read the article

• The best way to have a pointer to several methods - critique requested

  - by user827992

  I'm starting with a short introduction of what i know from the C language: a pointer is a type that stores an adress or a NULL the * operator reads the left value of the variable on its right and use this value as address and reads the value of the variable at that address the & operator generate a pointer to the variable on its right so i was thinking that in C++ the pointers can work this way too, but i was wrong, to generate a pointer to a static method i have to do this: #include <iostream> class Foo{ public: static void dummy(void){ std::cout << "I'm dummy" << std::endl; }; }; int main(){ void (*p)(); p = Foo::dummy; // step 1 p(); p = &(Foo::dummy); // step 2 p(); p = Foo; // step 3 p->dummy(); return(0); } now i have several questions: why step 1 works why step 2 works too, looks like a "pointer to pointer" for p to me, very different from step 1 why step 3 is the only one that doesn't work and is the only one that makes some sort of sense to me, honestly how can i write an array of pointers or a pointer to pointers structure to store methods ( static or non-static from real objects ) what is the best syntax and coding style for generating a pointer to a method?

  Read the article

• Object oriented wrapper around a dll

  - by Tom Davies

  So, I'm writing a C# managed wrapper around a native dll. The dll contains several hundred functions. In most cases, the first argument to each function is an opaque handle to a type internal to the dll. So, an obvious starting point for defining some classes in the wrapper would be to define classes corresponding to each of these opaque types, with each instance holding and managing the opaque handle (passed to its constructor) Things are a little awkward when dealing with callbacks from the dll. Naturally, the callback handlers in my wrapper have to be static, but the callbacks arguments invariable contain an opaque handle. In order to get from the static callback back to an object instance, I've created a static dictionary in each class, associating handles with class instances. In the constructor of each class, an entry is put into the dictionary, and this entry is then removed in the Destructors. When I receive a callback, I can then consult the dictionary to retrieve the class instance corresponding to the opaque reference. Are there any obvious flaws to this? Something that seems to be a problem is that the existence static dictionary means that the garbage collector will not act on my class instances that are otherwise unreachable. As they are never garbage collected, they never get removed from the dictionary, so the dictionary grows. It seems I might have to manually dispose of my objects, which is something absolutely would like to avoid. Can anyone suggest a good design that allows me to avoid having to do this?

  Read the article

• How to use mount points in MilkShape models?

  - by vividos

  I have bought the Warriors & Commoners model pack from Frogames and the pack contains (among other formats) two animated models and several non-animated objects (axe, shield, pilosities, etc.) in MilkShape3D format. I looked at the official "MilkShape 3D Viewer v2.0" (msViewer2.zip at http://www.chumba.ch/chumbalum-soft/ms3d/download.html) source code and implemented loading the model, calculating the joint matrices and everything looks fine. In the model there are several joints that are designated as the "mount points" for the static objects like axe and shield. I now want to "put" the axe into the hand of the animated model, and I couldn't quite figure out how. I put the animated vertices in a VBO that gets updated every frame (I know I should do this with a shader, but I didn't have time to do this yet). I put the static vertices in another VBO that I want to keep static and not updated every frame. I now tried to render the animated vertices first, then use the joint matrix for the "mount joint" to calculate the location of the static object. I tried many things, and what about seems to be right is to transpose the joint matrix, then use glMatrixMult() to transform the modelview matrix. For some objects like the axe this is working, but not for others, e.g. the pilosities. Now my question: How is this generally implemented when using bone/joint models, and especially with MilkShape3D models? Am I on the right track?

  Read the article

• Restrictive routing best practices for Google App Engine with python?

  - by Aleksandr Makov

  Say I have a simple structure: app = webapp2.WSGIApplication([ (r'/', 'pages.login'), (r'/profile', 'pages.profile'), (r'/dashboard', 'pages.dash'), ], debug=True) Basically all pages require authentication except for the login. If visitor tries to reach a restrictive page and he isn't authorized (or lacks privileges) then he gets redirected to the login view. The question is about the routing design. Should I check the auth and ACL privs in each of the modules (pages.profile and pages.dash from example above), or just pass all requests through the single routing mechanism: app = webapp2.WSGIApplication([ (r'/', 'pages.login'), (r'/.+', 'router') ], debug=True) I'm still quite new to the GAE, but my app requires authentication as well as ACL. I'm aware that there's login directive on the server config level, but I don't know how it works and how I can tight it with my ACL logic and what's worse I cannot estimate time needed to get it running. Besides, it looks only to provide only 2 user groups: admin and user. In any case, that's the configuration I use: handlers: - url: /favicon.ico static_files: static/favicon.ico upload: static/favicon.ico - url: /static/* static_dir: static - url: .* script: main.app secure: always Or I miss something here and ACL can be set in the config file? Thanks.

  Read the article

• Cisco PIX firewall blocking inbound Exchange email

  - by sumsaricum

  [Cisco PIX, SBS2003] I can telnet server port 25 from inside but not outside, hence all inbound email is blocked. (as an aside, inbox on iPhones do not list/update emails, but calendar works a charm) I'm inexperienced in Cisco PIX and looking for some assistance before mails start bouncing :/ interface ethernet0 auto interface ethernet1 100full nameif ethernet0 outside security0 nameif ethernet1 inside security100 hostname pixfirewall domain-name ciscopix.com fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 no fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names name 192.168.1.10 SERVER access-list inside_outbound_nat0_acl permit ip 192.168.1.0 255.255.255.0 192.168.1.96 255.255.255.240 access-list outside_cryptomap_dyn_20 permit ip any 192.168.1.96 255.255.255.240 access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq 3389 access-list outside_acl permit tcp any interface outside eq ftp access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq https access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq www access-list outside_acl permit tcp any interface outside eq 993 access-list outside_acl permit tcp any interface outside eq imap4 access-list outside_acl permit tcp any interface outside eq 465 access-list outside_acl permit tcp any host 213.xxx.xxx.xxx eq smtp access-list outside_cryptomap_dyn_40 permit ip any 192.168.1.96 255.255.255.240 access-list COMPANYVPN_splitTunnelAcl permit ip 192.168.1.0 255.255.255.0 any access-list COMPANY_splitTunnelAcl permit ip 192.168.1.0 255.255.255.0 any access-list outside_cryptomap_dyn_60 permit ip any 192.168.1.96 255.255.255.240 access-list COMPANY_VPN_splitTunnelAcl permit ip 192.168.1.0 255.255.255.0 any access-list outside_cryptomap_dyn_80 permit ip any 192.168.1.96 255.255.255.240 pager lines 24 icmp permit host 217.157.xxx.xxx outside mtu outside 1500 mtu inside 1500 ip address outside 213.xxx.xxx.xxx 255.255.255.128 ip address inside 192.168.1.1 255.255.255.0 ip audit info action alarm ip audit attack action alarm ip local pool VPN 192.168.1.100-192.168.1.110 pdm location 0.0.0.0 255.255.255.128 outside pdm location 0.0.0.0 255.255.255.0 inside pdm location 217.yyy.yyy.yyy 255.255.255.255 outside pdm location SERVER 255.255.255.255 inside pdm logging informational 100 pdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_outbound_nat0_acl nat (inside) 1 0.0.0.0 0.0.0.0 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx 3389 SERVER 3389 netmask 255.255.255.255 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx smtp SERVER smtp netmask 255.255.255.255 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx https SERVER https netmask 255.255.255.255 0 0 static (inside,outside) tcp 213.xxx.xxx.xxx www SERVER www netmask 255.255.255.255 0 0 static (inside,outside) tcp interface imap4 SERVER imap4 netmask 255.255.255.255 0 0 static (inside,outside) tcp interface 993 SERVER 993 netmask 255.255.255.255 0 0 static (inside,outside) tcp interface 465 SERVER 465 netmask 255.255.255.255 0 0 static (inside,outside) tcp interface ftp SERVER ftp netmask 255.255.255.255 0 0 access-group outside_acl in interface outside route outside 0.0.0.0 0.0.0.0 213.zzz.zzz.zzz timeout xlate 0:05:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout sip-disconnect 0:02:00 sip-invite 0:03:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ max-failed-attempts 3 aaa-server TACACS+ deadtime 10 aaa-server RADIUS protocol radius aaa-server RADIUS max-failed-attempts 3 aaa-server RADIUS deadtime 10 aaa-server RADIUS (inside) host SERVER *** timeout 10 aaa-server LOCAL protocol local http server enable http 217.yyy.yyy.yyy 255.255.255.255 outside http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server community public no snmp-server enable traps floodguard enable sysopt connection permit-ipsec crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5 crypto dynamic-map outside_dyn_map 40 match address outside_cryptomap_dyn_40 crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-MD5 crypto dynamic-map outside_dyn_map 60 match address outside_cryptomap_dyn_60 crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-MD5 crypto dynamic-map outside_dyn_map 80 match address outside_cryptomap_dyn_80 crypto dynamic-map outside_dyn_map 80 set transform-set ESP-3DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map client authentication RADIUS LOCAL crypto map outside_map interface outside isakmp enable outside isakmp policy 20 authentication pre-share isakmp policy 20 encryption 3des isakmp policy 20 hash md5 isakmp policy 20 group 2 isakmp policy 20 lifetime 86400 telnet 217.yyy.yyy.yyy 255.255.255.255 outside telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 217.yyy.yyy.yyy 255.255.255.255 outside ssh 0.0.0.0 255.255.255.0 inside ssh timeout 5 management-access inside console timeout 0 dhcpd address 192.168.1.20-192.168.1.40 inside dhcpd dns SERVER 195.184.xxx.xxx dhcpd wins SERVER dhcpd lease 3600 dhcpd ping_timeout 750 dhcpd auto_config outside dhcpd enable inside : end I have Kiwi SysLog running but could use some pointers in that regard to narrow down the torrent of log messages, if that helps?!

  Read the article

• How can I protect files on my NGiNX server?

  - by Jean-Nicolas Boulay Desjardins

  I am trying to protect files on my server (multiple types), with NGiNX and PHP. Basically I want people to have to sign in to the website if they want to access those static files like images. DropBox does it very well. Where by they force you to sign in to access any static files you put on there server. I though about using NGiNX Perl Module. And I would write a perl script that would check the session to see if the user was sign in to give them access to a static file. I would prefer using PHP because all my code is running under PHP and I am not sure how to check a session created by PHP with PERL. So basically my question is: How can I protect static files of any types that would need the user to have sign in and have a valid session created with a PHP script?

  Read the article

• Getting the total number of processors a computer has (c#)

  - by mbcrump

  Here is a code snippet for getting the total number of processors a computer has without using Environment.ProcessorCount. I found out that Environment.ProcessorCount is not necessary returning the correct value on some Intel based CPU’s.   using System; usingSystem.Collections.Generic; usingSystem.Linq; usingSystem.Text; usingSystem.Globalization; usingSystem.Runtime.InteropServices; namespaceConsoleApplication4 {     classProgram    {         static voidMain(string[] args)         {             int c = ProcessorCount;             Console.WriteLine("The computer has {0} processors", c);             Console.ReadLine();         }         private static classNativeMethods        {             [StructLayout(LayoutKind.Sequential)]             internal struct SYSTEM_INFO            {                 public ushort wProcessorArchitecture;                 public ushort wReserved;                 public uint dwPageSize;                 publicIntPtr lpMinimumApplicationAddress;                 publicIntPtr lpMaximumApplicationAddress;                 publicUIntPtr dwActiveProcessorMask;                 public uint dwNumberOfProcessors;                 public uint dwProcessorType;                 public uint dwAllocationGranularity;                 public ushort wProcessorLevel;                 public ushort wProcessorRevision;             }             [DllImport("kernel32.dll", CharSet = CharSet.Auto, ExactSpelling = true)]             internal static extern voidGetNativeSystemInfo(refSYSTEM_INFOlpSystemInfo);         }         public static int ProcessorCount         {             get            {                 NativeMethods.SYSTEM_INFOlpSystemInfo = newNativeMethods.SYSTEM_INFO();                 NativeMethods.GetNativeSystemInfo(reflpSystemInfo);                 return(int)lpSystemInfo.dwNumberOfProcessors;             }         }     } }

  Read the article

• Project Euler Problem 14

  - by MarkPearl

  The Problem The following iterative sequence is defined for the set of positive integers: n n/2 (n is even) n 3n + 1 (n is odd) Using the rule above and starting with 13, we generate the following sequence: 13 40 20 10 5 16 8 4 2 1 It can be seen that this sequence (starting at 13 and finishing at 1) contains 10 terms. Although it has not been proved yet (Collatz Problem), it is thought that all starting numbers finish at 1. Which starting number, under one million, produces the longest chain? NOTE: Once the chain starts the terms are allowed to go above one million. The Solution   public static long NextResultOdd(long n) { return (3 * n) + 1; } public static long NextResultEven(long n) { return n / 2; } public static long TraverseSequence(long n) { long x = n; long count = 1; while (x > 1) { if (x % 2 == 0) x = NextResultEven(x); else x = NextResultOdd(x); count++; } return count; } static void Main(string[] args) { long largest = 0; long pos = 0; for (long i = 1000000; i > 1; i--) { long temp = TraverseSequence(i); if (temp > largest) { largest = temp; pos = i; } } Console.WriteLine("{0} - {1}", pos, largest); Console.ReadLine(); }

  Read the article

• Is there any way to optimize my search blob program?

  - by Vicky

  I written this code to search the blob items (text files) on the basis of there content. For ex : if I search for "Good", then the files that contains "Good or good" word the name of that files should appear in search result. My code is working but i want to optimize it. class BlobSearch { public static int num = 1; static void Main(string[] args) { string accountName = "accountName"; string accessKey = "accesskey"; string azureConString = "DefaultEndpointsProtocol=https;AccountName=" + accountName + ";AccountKey=" + accessKey; string blob = "MyBlobContainer"; string searchText = string.Empty; Console.WriteLine("Type and enter to search : "); searchText = Console.ReadLine(); CloudStorageAccount account = CloudStorageAccount.Parse(azureConString); CloudBlobClient blobClient = account.CreateCloudBlobClient(); CloudBlobContainer blobContainer = blobClient.GetContainerReference(blob); blobContainer.FetchAttributes(); var blobItemList = blobContainer.ListBlobs(); GetBlobList(searchText, blobContainer, blobItemList); Console.ReadLine(); } private static async void GetBlobList(string searchText, CloudBlobContainer blobContainer, IEnumerable<IListBlobItem> blobItemList) { foreach (var item in blobItemList) { string line = string.Empty; CloudBlockBlob blockBlob = blobContainer.GetBlockBlobReference(item.Uri.ToString()); if (blockBlob.Name.Contains(".txt")) { await Search(searchText, blockBlob); } } } private async static Task Search(string searchText, CloudBlockBlob blockBlob) { string text = await blockBlob.DownloadTextAsync(); if (text.ToLower().IndexOf(searchText.ToLower()) != -1) { Console.WriteLine("Result : " + num + " => " + blockBlob.Name.Substring(blockBlob.Name.LastIndexOf('/') + 1)); num++; } } } I think blobContainer.ListBlobs(); is blocking code because search will not work until all the blob items loaded. Is there anyway to optimize it or anywhere else in my code. Thanks

  Read the article

• RESOLVED Why does IPtables's NAT stop working when I enable the firewall's third interface?

  - by Kronick

  On my firewall I've three interfaces : eth0 : public IP (46.X.X.X.) eth0:0 public IP (46.X.X.Y.) eth1 : public IP (88.X.X.X.) eth2 : private LAN (172.X.X.X) I've setup a basic NAT which works great until I turn on the eth1 interface, I basically loose the connectivity. When I turn off the interface (ifconfig eth1 down) then the NAT re-work. I've added some policy routing via iproute, which makes my three public IP's available. I don't understand why turning on eth1 on makes the LAN unavailable. PS : weirder ; when I turn on eth1 BUT remove the NAT, then the firewall is accessible by using the public IPS. So to me it's exclusively a NAT issue, since without the NAT the network works while with the NAT without the second public interface, the NAT does work. Regards EDIT : I've been able to make it work by using iproute2 rules. That was definitely a routing issue. Here is what I did : ip rule add prio 50 table main ip rule add prio 201 from ip1/netmask table 201 ip rule add prio 202 from ip2/netmask table 202 ip route add default via gateway1 dev interface1 src ip1 proto static table 201 ip route append prohibit default table 201 metric 1 proto static ip route add default via gateway2 dev interface2 src ip2 proto static table 202 ip route append prohibit default table 202 metric 1 proto static # mutipath ip rule add prio 221 table 221 ip route add default table 221 proto static \ nexthop via gateway1 dev interface1 weight 2\ nexthop via gateway2 dev interface2 weight 3

  Read the article

• @staticmethod vs module-level function

  - by darkfeline

  This is not about @staticmethod and @classmethod! I know how staticmethod works. What I want to know is the proper use cases for @staticmethod vs. a module-level function. I've googled this question, and it seems there's some general agreement that module-level functions are preferred over static methods because it's more pythonic. Static methods have the advantage of being bound to its class, which may make sense if only that class uses it. However, in Python functionality is usually organized by module not class, so usually making it a module function makes sense too. Static methods can also be overridden by subclasses, which is an advantage or disadvantage depending on how you look at it. Although, static methods are usually "functionally pure" so overriding it may not be smart, but it may be convenient sometimes (though this may be one of those "convenient, but NEVER DO IT" kind of things only experience can teach you). Are there any general rule-of-thumbs for using either staticmethod or module-level functions? What concrete advantages or disadvantages do they have (e.g. future extension, external extension, readability)? If possible, also provide a case example.

  Read the article

• Django | Apache | Deploy website behind SSL

  - by planet260

  So here are my requirements. I have a website built in Django. I deployed it on Apache Ubuntu. Before there was no SSL involved so the deployment was pretty simple. But now the requirements are changed. Now I have to take a few actions like signup and login behind SSL and present the admin panel and other normally via HTTP. By following the this tutorial I have set-up Apache and SSL and generated certificates for SSL communication. But I am not sure how to proceed, ie. how to serve only a few of my actions through SSL. Below is my configuration. The normal actions are working fine but I don't know how to configure SSL calls. WSGIScriptAlias / /home/ubuntu/myproject/src/myproject/wsgi.py WSGIPythonPath /home/ubuntu/myproject/src <VirtualHost *:80> ServerName mydomain.com <Directory /home/ubuntu/myproject/src/myproject> <Files wsgi.py> order deny,allow Allow from all </Files> </Directory> Alias /static/admin/ "/home/ubuntu/myproject/src/static/admin/" <Directory "/home/ubuntu/myproject/src/static/admin/"> Order allow,deny Options Indexes Allow from all IndexOptions FancyIndexing </Directory> <Location "/login"> RewriteEngine on RewriteRule /admin(.*)$ https://mydomain.com/login$1 [L,R=301] </Location> </VirtualHost> <VirtualHost *:443> ServerName mydomain.com SSLEngine on SSLOptions +StrictRequire SSLCertificateFile /etc/apache2/ssl/apache.crt SSLCertificateKeyFile /etc/apache2/ssl/apache.key <Directory /home/ubuntu/myproject/src/myproject> <Files wsgi.py> order deny,allow Allow from all </Files> </Directory> Alias /static/admin/ "/home/ubuntu/myproject/src/static/admin/" <Directory "/home/ubuntu/myproject/src/static/admin/"> Order allow,deny Options Indexes Allow from all IndexOptions FancyIndexing </Directory> </VirtualHost> Can you please help me out on how to achieve this? What am I doing wrong? I have read a lot of tutorials but honestly I am not really good at configurations. Any help is appreciated.

  Read the article

• Bridging networks problems

  - by Eric

  In my setup I have 3 computers and 2 (wireless d-link) routers. Computer1 has ethernet and wireless interfaces ethernet : 192.168.0.x (DHCP) wireless : 192.168.10.254 (static) Computer 2 has ethernet with two ips ethernet1 : 192.168.0.90 (static) ethernet2 : 192.168.10.110 (static) Computer 3 is a particular device with a hardcoded ip that I can't change wireless : 192.168.10.41 (static) Router1 manages internet and DHCP for network 192.168.0.0/24 Router2 is more complicated. I don't use DHCP. I use it to bridge between both networks. Its static ip is 192.168.10.1 Computer1 can ping Computer2. Computer1 can ping Computer3. Computer1 can ping Router1. Computer1 cannot ping Router2. Computer2 cannot ping Computer3. Computer2 can ping Router2. Router1 can ping Router1 Router2 can ping Computer2 Router2 cannot ping Computer1 Router2 cannot ping Computer3 This is very weird. Router2 manages the wireless connection, it should be able to ping its own computers right? My question is obviously : How can I make it so Computer2 can access everything else. This is a traditional case of "it was working before christmas and now it doesn't". The ethernet wiring is as follow : [ Computer1 ]----[ Router1 ]---[ Router2 ]---[ Computer3 ] I am using switch (lan) ports on Router1/2.

  Read the article

• Routing / binding 128 to one server

  - by Andrew

  I have a Ubuntu server with 128 ip's (static external ips 86.xx.xx.16), and I want to crawl pages thru different ip's. The gateway is xx.xxx.xxx.1, the main ip is xx.xxx.xxx.16, and the other 128 ip's are xx.xxx.xxx.129/255. I tried this configuration in /etc/network/interfaces but I doesn't work. It work if I remove the gateway for the aliases eth0:0 and eth0:1. I think this is routing problem. auto lo iface lo inet loopback auto eth0 auto eth0:0 auto eth0:1 iface eth0 inet static address xx.xxx.xxx.16 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:0 inet static address xx.xxx.xxx.129 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:1 inet static address xx.xxx.xxx.130 netmask 255.255.255.128 gateway xx.xxx.xxx.1 Also, please tell me how to "reset" every changes that I made in networking and routing. Thank you

  Read the article

< Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >