Search Results

Search found 7599 results on 304 pages for 'auto versioning'.

Page 124/304 | < Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >

  • My facebook blocking ACL has stopped working

    - by Josh
    This probably very simple. This was setup before I arrived, and has been working to block facebook. I recently eliminated some static port forwarding on this 2691 (as in, I don't think anything else has changed), and now facebook is once again accessible. Why is this list not doing what it seems like it should be doing (and was doing)? Would an extended outbound ACL be more appropriate (I think that would have been my thought if I had been tasked with creating this in the first place)? Something different? I've included below what I believe are the relevant parts of the config. interface FastEthernet0/0 ip address my.pub.ip.add my.ip.add.msk ip access-group 1 in ip nat outside ip virtual-reassembly duplex auto speed auto access-list 1 deny 69.171.224.0 0.0.31.255 access-list 1 deny 74.119.76.0 0.0.3.255 access-list 1 deny 204.15.20.0 0.0.3.255 access-list 1 deny 66.220.144.0 0.0.15.255 access-list 1 deny 69.63.176.0 0.0.15.255 access-list 1 permit any ip nat inside source list 105 interface FastEthernet0/0 overload access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.8.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 105 permit ip 192.168.1.0 0.0.0.255 any EDIT ACL is once again blocking Facebook. Here is the new definition for those interested... access-list 1 deny 66.220.144.0 0.0.7.255 access-list 1 deny 66.220.152.0 0.0.7.255 access-list 1 deny 69.63.176.0 0.0.7.255 access-list 1 deny 69.63.176.0 0.0.0.255 access-list 1 deny 69.63.184.0 0.0.7.255 access-list 1 deny 69.171.224.0 0.0.15.255 access-list 1 deny 69.171.239.0 0.0.0.255 access-list 1 deny 69.171.240.0 0.0.15.255 access-list 1 deny 69.171.255.0 0.0.0.255 access-list 1 deny 74.119.76.0 0.0.3.255 access-list 1 deny 173.252.64.0 0.0.31.255 access-list 1 deny 173.252.70.0 0.0.0.255 access-list 1 deny 173.252.96.0 0.0.31.255 access-list 1 deny 204.15.20.0 0.0.3.255 access-list 1 permit any

    Read the article

  • RHEL 6.x on Rackspace Cloud and Dedicated hardware experiencing Redis Timeouts

    - by zhallett
    I just recently set up a mixture of RHEL 6.1 Rackspace cloud hosts and RHEL 6.2 dedicated hosts using Rackconnect. I am experiencing intermittent Redis timeouts from within our Rails 3.2.8 app with Redis 2.4.16 running on the RHEL 6.2 dedicated hosts. There is no network latency or packet loss. Also there are no errors on any interfaces on our cloud or dedicated servers or on the managed firewall from Rackspace. When Redis timesout, there is nothing logged within redis even though it is set up to do debug logging. The only error we receive is from Airbrake saying there was a Redis timeout. Network topology: RHEL 6.1 cloud hosts <--> Alert logic IDS <--> Cisco ASA 5510 <--> RHEL 6.2 dedicated hosts (web nodes) (two way NAT) (db hosts running redis) Ping from db host to web host: 64 bytes from 10.181.230.180: icmp_seq=998 ttl=64 time=0.520 ms 64 bytes from 10.181.230.180: icmp_seq=999 ttl=64 time=0.579 ms 64 bytes from 10.181.230.180: icmp_seq=1000 ttl=64 time=0.482 ms --- web1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999007ms rtt min/avg/max/mdev = 0.359/0.535/5.684/0.200 ms Ping from web host to db host: 64 bytes from 192.168.100.26: icmp_seq=998 ttl=64 time=0.544 ms 64 bytes from 192.168.100.26: icmp_seq=999 ttl=64 time=0.452 ms 64 bytes from 192.168.100.26: icmp_seq=1000 ttl=64 time=0.529 ms --- data1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999017ms rtt min/avg/max/mdev = 0.358/0.499/6.120/0.201 ms Redis config: daemonize yes pidfile /var/run/redis/6379/redis_6379.pid port 6379 timeout 0 loglevel debug logfile /var/lib/redis/log syslog-enabled yes syslog-ident redis-6379 syslog-facility local0 databases 16 save 900 1 save 300 10 save 60 10000 rdbcompression yes dbfilename dump-6379.rdb dir /var/lib/redis maxclients 10000 maxmemory-policy volatile-lru maxmemory-samples 3 appendfilename appendonly-6379.aof appendfsync everysec no-appendfsync-on-rewrite no auto-aof-rewrite-percentage 100 auto-aof-rewrite-min-size 64mb slowlog-log-slower-than 10000 slowlog-max-len 1024 vm-enabled no vm-swap-file /tmp/redis.swap vm-max-memory 0 vm-page-size 32 vm-pages 134217728 vm-max-threads 4 hash-max-zipmap-entries 512 hash-max-zipmap-value 64 list-max-ziplist-entries 512 list-max-ziplist-value 64 set-max-intset-entries 512 zset-max-ziplist-entries 128 zset-max-ziplist-value 64 activerehashing yes Redis-cli info: redis-cli info redis_version:2.4.16 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:64 multiplexing_api:epoll gcc_version:4.4.6 process_id:4174 uptime_in_seconds:79346 uptime_in_days:0 lru_clock:1064644 used_cpu_sys:13.08 used_cpu_user:19.81 used_cpu_sys_children:1.56 used_cpu_user_children:7.69 connected_clients:167 connected_slaves:0 client_longest_output_list:0 client_biggest_input_buf:0 blocked_clients:6 used_memory:15060312 used_memory_human:14.36M used_memory_rss:22061056 used_memory_peak:15265928 used_memory_peak_human:14.56M mem_fragmentation_ratio:1.46 mem_allocator:jemalloc-3.0.0 loading:0 aof_enabled:0 changes_since_last_save:166 bgsave_in_progress:0 last_save_time:1352823542 bgrewriteaof_in_progress:0 total_connections_received:286 total_commands_processed:507254 expired_keys:0 evicted_keys:0 keyspace_hits:1509 keyspace_misses:65167 pubsub_channels:0 pubsub_patterns:0 latest_fork_usec:690 vm_enabled:0 role:master db0:keys=6,expires=0 edit 1: add redis-cli info output

    Read the article

  • Cleanup Windows XP on Netbook

    - by stacker
    I already moved all installed application software to drive D: but C: (4GB SD) is full since auto update to SP3. I don't need or want things like Media Player,Messenger,Movie Maker,or Internet Explorer and all this stuff I never asked for. How can I get rid of them?

    Read the article

  • Multiline code in Word 2007

    - by WaelJ
    I am using word 2007 and am inserting code into the document. I have a style with a fixed-width font and light grey background and all, and I use Notepad++ for syntax highlighting. My problem is with a "line" of code that is too long to display, so is there a way to auto-insert an arrow symbol at the beginning of a such lines to indicate that it is the same line (kind of like hyphenating, except on long lines instead of long words) So for e.g. something like this: public static void foo(String abcdefg, Boolean 123, ?String xyz)

    Read the article

  • Change the language of fields in Microsoft Word

    - by Martin Wiboe
    Hi, I am using Word 2010 and some built-in features with fields, such as bibliography. My Word installation is English and I am writing a report in US English. However, my computer has its locale set to Denmark. This affects the formatting of dates and some of the text in the auto-generated fields (e.g. in bibliography it says "citeret:" instead of "cited:"). How can I change the language of the fields to US English? Thanks, Martin

    Read the article

  • Promote document data to meta-data

    - by antony.trupe
    Is there a way to "promote" information in a document(Word, Visio, etc) to "meta-data" that can be auto-magically represented in a SharePoint list? I want to be able to create metrics on information in documents without duplicating the data in the document in a column of the list.

    Read the article

  • Aliased network interfaces and isc dhcp server

    - by Jonatan
    I have been banging my head on this for a long time now. There are many discussions on the net about this and similar problems, but none of the solutions seems to work for me. I have a Debian server with two ethernet network interfaces. One of them is connected to internet, while the other is connected to my LAN. The LAN network is 10.11.100.0 (netmask 255.255.255.0). We have some custom hardware that use network 10.4.1.0 (netmask 255.255.255.0) and we can't change that. But we need all hosts on 10.11.100.0 to be able to connect to devices on 10.4.1.0. So I added an alias for the LAN network interface so that the Debian server acts as a gateway between 10.11.100.0 and 10.4.1.0. But then the dhcp server stopped working. The log says: No subnet declaration for eth1:0 (no IPv4 addresses). ** Ignoring requests on eth1:0. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** No subnet declaration for eth1:1 (no IPv4 addresses). ** Ignoring requests on eth1:1. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** I had another server before, also running Debian but with the older dhcp3 server, and it worked without any problems. I've tried everything I can think of in dhcpd.conf etc, and I've also compared with the working configuration in the old server. The dhcp server need only handle devices on 10.11.100.0. Any hints? Here's all relevant config files: /etc/default/isc-dhcp-server INTERFACES="eth1" /etc/network/interfaces (I've left out eth0, that connects to the Internet, since there is no problem with that.) auto eth1:0 iface eth1:0 inet static address 10.11.100.202 netmask 255.255.255.0 auto eth1:1 iface eth1:1 inet static address 10.4.1.248 netmask 255.255.255.0 /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name "???.com"; option domain-name-servers ?.?.?.?; default-lease-time 86400; max-lease-time 604800; authorative; subnet 10.11.100.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; pool { range 10.11.100.50 10.11.100.99; } option routers 10.11.100.102; } I have tried to add shared-network etc, but didn't manage to get that to work. I get the same error message no matter what...

    Read the article

  • My pivot chart has the wrong Y axis values but correct data point values

    - by Mark Harnett
    I created a pivot chart based on some raw data for the x axis (dates) and 4 calculated fields for the Y values. The values on resulting lines are correct (see the data label at the end of the line) but the Y axis is off by about 100, but not off by any consistent amount. I have played with auto axis on and off, turn log scale on and off. All to no avail. Does anybody have any thoughts? Image link

    Read the article

  • my.cnf for big wordpress installation

    - by adnan
    My website using wordpress with more than 150K posts & using auto posts publish feature with more than 2K daily posts I need to configure my.cnf settings to speed up my website actually the website speed is good but i have a problem with facebook sharing when I trying to share some link in facebook the link appears as this image http://elnhrda.com/facelink.jpg So I need to speed up my website by configure my.cnf I have VPS 4G.B RAM 300 HDD CENTOS6 x86_64 processor Intel Dual Xeon L5420 (8 x 2.5 GHz) this is my current my.cnf [mysqld] query_cache_size=512M skip-name-resolve innodb_file_per_table=1 query_cache_limit=32M any suggestions may be help

    Read the article

  • Get sublime text 2 (sublimecodeintel) to parse mason

    - by user813182
    So Sublime Text 2 seems to getting a lot of love lately. I am using the Sublime Code intel plugin, https://github.com/Kronuz/SublimeCodeIntel for auto completion. The problem is, it does not recognize .mi files as MASON files. I looked into the lexer and it does have the keywords in place. How do I force it to be parsed as MASON? Running "Set Syntax: " on ctrl+shift+p, does not show a MASON option.

    Read the article

  • Alternatives to musicbrainz picard -audio-fingerprinting tagging services [closed]

    - by Journeyman Geek
    Possible Duplicate: Auto-tagging MP3s I'm currently using musicbranz picard to tag files that don't have any usable tagging information. For some reason, currently none of the files I trying to ID seem to be identified, despite some of them them being artists who are almost certainly on musicbrainz. So, I'm looking for something that uses an alternate database and does the same thing - to identify unknown music files off an audio fingerprint. Windows is preferred, but I would be fine with any of the big 3 OSes (Windows/Linux/OS X).

    Read the article

  • Keep remoting into wrong account. Windows 7

    - by Paul
    I have a home theatre PC running with two users accounts on windows 7. The default account logs into locally. The account 'Paul' is present but is denied local log in so the default auto logs in locally. I am trying to remote into account Paul using RDC however it tries to log into the default account and I am presented with an an option to boot the present user off so I can log in. How do I specify which account I want to log into?

    Read the article

  • Grub Error 18 - Solid State Drive

    - by clint
    I recently used Raw Copy to make an image of my 300gb Raptor Hd to a OCZ Vertex SSD 60GB. And When I pluged in the SSD to boot I get a Grub Error 18. I have tried to changed in the BIOS setting to LBA, Large, Auto, trying different combination's. Any advice. thanks, Clint

    Read the article

  • Any option to change Windows XP default Copy Here naming from "Copy of {name}.{ext}" to "{name}.{ext

    - by scunliffe
    Is there an option or tool that will allow me to change the default naming convention for files copied into the same directory in Windows (XP) and above. e.g. from: Copy of {name}.{ext} to: {name}.{ext}.copy Currently: original_file.php Copy of original_file.php Desired: original_file.php original_file.php.copy This would make finding/working with duplicated files much easier (they auto-sort together) and the filetype (by extension) changes thus it can't accidentally "break" something (e.g. if it were a *.java file, upon compiling I would get errors)

    Read the article

  • Select part of a text that exists already in an above cell

    - by pragadheesh
    How do I get Excel to partially auto-complete a word using another that already exist in the same worksheet? Let's say I have the word "Microsoft" in a cell and in the cell below I want to type the word "Microhard". When I start typing Microhard, the word Microsoft appears shaded in black. How can I select the "Micro" part alone from Microsoft and continue to fill out the rest with "hard" without it trying to fill out as Microsoft?

    Read the article

  • All password with '$' inside (phpmyadmin) won't work [UTF-8 problem]

    - by Tristan
    Hello, i set up a dedicaced server with a tutorial. I set in PHP : mbstring.language=UTF-8 mbstring.internal_encoding=UTF-8 mbstring.http_input=UTF-8 mbstring.http_output=UTF-8 mbstring.detect_order=auto But each time there is a $ in the password (i have one for the root of mysql + other script) the password won't work. For example, I just removed the $ in the password for a script, and it worked. When i connect @root on mysql via phpmyadmin : don't work When i connect @root via PHP : works What can i do for this problem please ?

    Read the article

  • Software to aid writing Research Papers

    - by Rogue
    Have been working on this white paper for weeks, and have been having a very rough time with all the links and reference material i have found online, finally got them organized but this is a very manual procedure are there any software's that: 1) Organize , sort and bookmark your links and reference pages and give you one click access to them 2) Auto generate the bibliography, based on what you already linked 3) Give you templates of research paper layouts 4) Templates and examples of index's P.S: Need software for Windows XP, and it can be a paid software

    Read the article

< Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >