Search Results

Search found 4186 results on 168 pages for 'ember router'.

Page 125/168 | < Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >

• Cascading switches: uplink to uplink?

  - by wuckachucka

  I'm a bit confused as to why I haven't seen any references online to using Switch A's uplink port (1Gbps, 24-port 10/100) to connect to Switch B's uplink port: everything I've seen -- including documentation, forums, articles, etc. -- has Switch A's uplink port going to one of Switch B's 10/100 access ports. As I understand it, the Uplink port (besides greater speed normally) is no different than another port except that it's "internally crossed-over" so that you can use a straight cable with it. I've also seen documentation on using the uplink port to connect a switch to a gateway router, or even a server, as it provides greater bandwidth than the access ports, but yet not sure why nobody seems to be cross-uplinking, even when there's 2 uplink ports available on some higher-end switches. Switch in question is Linksys SRW224P (x2). Am I missing something?

  Read the article

• Windows 7 freezes on connecting second time to same wifi network

  - by Rakesh Juyal

  I am using Lenovo - y470, which comes with windows 7 home premium. I can connect to my wifi network and there is no issue in that. But the problem comes if the network get disconnected and i again try to connect to same wifi network. As soon as i click on connect my system freezes, and i can not even press ctrl+ alt+ del . The only think i am allowed to do at that time is press and hold power button to shut down the system and restart it again. Please tell me how to resolve this issue. Please let me know if some more information is required. OS: Windows 7 Router: Netgear n-150

  Read the article

• Packet loss with all adapters on one PC only on the LAN

  - by Enigmativity

  I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

  Read the article

• Get source and destination of outbound traffic in pfSense

  - by maxsilver

  I'm looking at the traffic graph in pfSense (Version 1.2.2), which we're using as a router / NAT / ect on our network. Recently, I'm seeing a sudden, constant spike of 15 - 30kbps traffic outbound, that is unusual for our network (normally its below 2kbps, we're mostly all inbound traffic) Is there any way to determine what the source of this traffic is, or where it's going? (Just an internal IP address for source, and external IP address for destination would be all I need) I've already tried switching the traffic graph to 'LAN' and watching the host list on the right side, but it seems ... flakey. The numbers it shows seem to fade in and out at random, and the values never add up to anywhere near the graph values. I'm not allowed to post the image, but a photo is available at - http://imgur.com/QYjKI.png

  Read the article

• Connecting two pcs through cable, at the same time as wireless

  - by Steffen

  I've got 2 pcs setup with WLAN - however when I copy files between the machines it takes forever (obviously, since I run 801.11g). So I thought, why not just connect them directly with a cable (my wireless router is the other end of the house, that's why I don't use cables to that) However how should I configure the LAN connection on each machine, so I can use it for transferring files between them, whilst using my WLAN to access the Internet ? I was thinking about letting one machine be gateway, but then Windows pops up with a lot of warnings (basically it says this won't work when you're using two disjoint networks) And now I'm at a loss as to what to try.

  Read the article

• GNS3 Cannot ping/resolve DNS record

  - by Eldad Cohen

  I set up an internet lab with GNS3, which has 3 routers, in each node there is a computer directly connected. One of the hosts is a DNS server, Windows 2003 Server. The other one is a Windows XP machine. Ping is good between routers and machines but no ability to ping domain.com record on DNS server 2003. I set a static nat on the router to route all traffic from gateway to the DNS server internal ip address, still no answer for the dns request. Any ideas or thoughts will be most welcome.

  Read the article

• Should I upgrade my LinkSys WRT54GL firmware?

  - by Reid

  I have a LinkSys WRT54GL v1.1 which currently has stock firmware version 4.30.7. I see that version 4.30.14 is available. The router works fine now, and the release notes look uninteresting except for one line in v4.30.9: "Resolves issue with Linux kernel vulnerability". I have remote management turned off. I'm aware of the 3rd-party firmwares but the stock firmware works fine for me at the moment, so I don't have an interest in those. Is the status quo fine or should I upgrade the firmware? (It's a bit of a pain since the config has to be saved and reloaded, and obviously any mucking with firmware is risky.)

  Read the article

• Block p2p downloading in my office?

  - by Andrew

  I work in an education office in a third world country. We pay for internet by the megabyte (no other choice) and have lately been using an incredible amount of bandwidth. This is because the office staff have found out about p2p sharing. As far as I know, Limewire is the only program they're using, but I'm sure it's just a matter of time before they discover the more general world of bittorrent. Using only a linksys router (that I could flash), is there any way for me prevent the office from destroying our bandwidth cap by downloading personal items (against policy). Even semi-fixes would be better than nothing.

  Read the article

• Remote connection to dynamic public ip & private ip addresses

  - by user53864

  Many times I connected to windows computer which has static public ip address via remote desktop over wan links. I'm wondering how could I connect to the remote computer that has dynamic public ip address & private ip addresses assigned. I've 2 systems at home: xp system-------connected to internet(dynamic public ip) & allowed other users to connected to the internet on the interface. windows vista system--------enabled dhcp on the interface to access internet from xp. How could I remotely connect from my office to the 'vista system'?. If I've a router/modem at my home it may be possible to allow the ports for the system but I don't. Any tips?

  Read the article

• dd-wrt Bonjour/ netbios etc on two subnets

  - by user72182

  Hi I was wondering if any clever people out there could help me. I have a network setup with two different subnets 192.168.1.0 and 192.168.0.0 one router is connected to a VPN (via OpenVPN) the other is not. Both routers have static routes to each other and a device on one can communicate to another without issues when using IP addresses. My problem is I want to use services like Bonjour, Netbios and Apple Talk across the two networks, which currently does not work. A laptop connected on one subnet will not see a laptop connected on another. Is there anyway that you can connect the two networks together so these sort of local service will work??? I guess I have to forward the boardcast packets but I have no idea how to do this. Thanks for any help...

  Read the article

• Why does WebDAV fail from inside home network

  - by Claus

  On my OSX server there is a folder that is configured in the Server App to be accessible via WebDAV. This folder is used to sync OmniFocus. On my router, I have set up a dynamic dns. When I am outside my home network (physically away or when connected via a vpn), I can connect and sync fine via: https://<server name from dyndns>/<username>/<path to WebDAV folder> However, when I am in my home network, the connection to WebDAV does not work (other connections, AFP, f.ex, do work). What could be some reasons why I can't connect to WebDAV from within my home network? What log files could give hints and where are they stored? I am running OSX server 10.9.3. and server.app. Thanks for your help.

  Read the article

• Purpose of LAN Domain?

  - by Leonard Thieu

  What is the purpose of creating a domain name for your LAN? I'm using DD-WRT on my router and assigned local.moofz.com as the LAN domain. I setup Apache HTTP servers on two of the computers on my LAN to test it out. I could reach them on oneil.local.moofz.com and vala.local.moofz.com, but I found out that I could also reach them via their hostnames oneil and vala. If I can reach them through their host names, then what would be the purpose of having a domain name for my LAN?

  Read the article

• Hosting 3 domains on 3 PC (1 domain per PC) with only 1 static IP address

  - by StealthRT

  Hey all i am trying to figure this out here. I have 3 PC's that are hooked into my router which i have a static IP for. I am currently hosting a web site (ex: blah1.com) on the 1st PC but have yet to connect PC 2 and 3 up to the network. That one PC thats online is using port 77. I direct all 80 traffic to port 77 using that servers IP address (192.168.x.xxx) My question is, how can i direct traffic for my other 2 domains (ex: blah2.com and blah3.com) to the 2 individual PC's (ip's) as i already am doing with the 1st PC if i can only use one port 80 to direct taffic to the website in?

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Nagios check_bgp_neighbors plugin showing critical status

  - by user141610

  I am trying to configure nagios check_bgp_neighbors plug-in on Ubuntu and followed README file of check_bgp_neighbors plug-in. I have made following changes: define command{ command_name check_bgp_all command_line $USER1$/check_bgp_neighbors -H $HOSTADDRESS$ -C $USER3$ -n $ARG1$ -n $ARG2$ } to define command{ command_name check_bgp_all command_line /usr/local/nagios/libexec/check_bgp_neighbors.sh -H xx.xx.xx.49 -C snmpName -n xx.xx.xx.50 And define service{ use server-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!10.0.0.1!172.16.0.2 } to define service{ use generic-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!xx.xx.xx.50 } xx.xx.xx.49 is the IP of the host router and xx.xx.xx.50 is the IP of eBGP neighbour. Status information: line: neighbor:xx.xx.xx.50:sent:78838:received:9769 Failed: status:6 prefixes:16 sent:0 received:1 Log [1353997904] SERVICE NOTIFICATION: router1;router1;BGP CHECK 2;CRITICAL;notify-service-by-email;line: neighbor:103.7.248.50:sent:78842:received:9772 [1353997904] SERVICE NOTIFICATION: router1;router1;BGP CHECK 2;CRITICAL;notify-service-by-sms;line: neighbor:103.7.248.50:sent:78842:received:9772 Why does it show critical status???? I am not getting response for this question, if you need additional information please mention it in comment.

  Read the article

• How do I configure tinydns (with fefe's IPv6 patch) to listen on IPv6 address?

  - by Christian Hudon

  I'm setting up my network to support IPv6. I have static IPv6 addresses assigned to each interface of my router, and radvd advertising different prefixes on each interface. The next step would be to get my dnscache (from djbdns) working on IPv6. Said dnscache has fefe's IPv6 patch applied, so I assume it should work with IPv6. However, I can't find any documentation online on how to make the patched dnscache listen on IPv6. How do I configure tinydns and dnscache to listen on IPv6 too?

  Read the article

• Resolving real IP address out of a dynamic dns address

  - by stavnir

  I recently opened a dynamic dns user (at no-ip for that matter..) for my own personal needs and especially for ssh-ing my computer whenever I need to, without knowing it's static IP. My questions are: Am I misusing the concept of dynamic dns? Are there more appropriate methods to do what I want to do? If not, how do I resolve my router's real ip address? Firefox somehow manages to do so, nslookup and other similar commands only resolve the ip of the ddns server (e.g. no-ip.org). Trying to figure this mystery with wireshark failed miserably ;)

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• D-Link DNS-323 NAS firmware update

  - by Mark Beaton

  Hi all, I've got a D-Link DNS-323 NAS enclosure holding a bunch of multimedia files that I've (possibly stupidly) just updated the firmware on, from 1.03 to 1.08. The updater indicated it applied the firmware patch successfully, but after rebooting it I can no longer get into it via the web interface, either via the static IP I had assigned it before the update, or by any of the DHCP-assigned addresses that I can see are currently assigned by my router. The unit just sits there, with the drives (2x512 set up as RAID-1) thrashing away seemingly forever... So, my question - has anyone had a similar experience with one of these units? Any advice etc? I've googled the hell out of it, and can't find anything useful.

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

  Read the article

• Windows 7 Utlimate x64 - No Internet access

  - by rafek

  I've just installed Windows 7 Ultimate x64. As all of my computers at home I've connected to my router via wifi (open/wep). And what has happened is that Wireless Connection is Connected but with No Internet access -- my ipconfig says: Autoconfiguration IPv4 Address : 169.254.33.161 Subnet Mask : 255.255.0.0 Default Gatewawy : (empty) After ipconfig /renew I get: An error occurred while renewing interface Wireless Network Connection : unable to contact your DHCP server. Request has timed out. [..] I'm looking for a solution for 2 hours now...

  Read the article

• Trouble accessing network drives in Windows 7

  - by Warlax

  Hi, Recently purchased a LaCiE network drive. Connected it to my router, configured it, added a user for myself. Installed the "Network Assistant" that came with it - no problem. Went to My Computer Network, found the network drive - was prompted for a login/password to see the contents, types \user and password (leading slash to get rid of DOMAIN) and accesses contents. There is one open share that I can access/mount without problem and there's another share with my user name as set-up via the network drive's web-based config. Double-clicked on that, prompted again. user/password doesn't work! It says I have no permissions but the user/pass combination is PERFECT. Some Windows Vista posts talk about a Local Security Policy menu - but that's nowhere to be found. Any ideas? (Windows 7 Professional BTW).

  Read the article

• IP assignment in a /28 block

  - by mks

  Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

  Read the article

• Why is this static routing not working ?

  - by geeko

  Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

  Read the article

• Microsoft Forefront Management Gateway 2010 - Which topology to choose for monitoring only server?

  - by MadBoy

  Hello, I've installed Forefront and wanted to use it as monitoring traffic solution until we decide to put it as a router. I've 2 nic's assigned to this virtual machine. One NIC has connected port which is "mirror port" of our WAN redirected on switch so it sees all the network traffic flying by. The other NIC is internet access. This server is located inside our lan network. What topology should i choose and which options I should look at to be able to see which traffic is used (SMTP, WWW etc) and who does what? We had cases of infected machines with spam and we want to be able to see that some machine is sending large amounts of mails. Is that possible ?

  Read the article

< Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >