Search Results

Search found 5885 results on 236 pages for 'finally'.

Page 125/236 | < Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >

• Is there a better way to do bonded vlan tagged interfaces with XEN

  - by AJ01

  We have a number of XEN servers all running CentOS or RHEL. The VM's that they run are all required to be on their own VLAN for no other reason than the customer expects them to be. Long story short however, I can't change this right now. We are also required to have bonding enabled on the interfaces. So to accommodat this we enslave eth1 and eth2 to bond0. We then create a seperate interface called bond0.VLANID where VLANID corresponds to the correct vlan; eg ifcfg-bond0.204 DEVICE=bond0.204 BOOTPROTO=static ONBOOT=yes VLAN=yes BRIDGE=xenvlan204 Bridge to XEN As you will see, we eventually have to bridge this out to XEN, and we do this by adding another interface called xenvlan204 (in this instance) which contains; ifcfg-xenvlan204 DEVICE=xenvlan204 BOOTPROTO=none ONBOOT=yes TYPE=bridge XEN Vm Config Finally in our XEN config for each VM, we add vif = [ "bridge=xenvlan204" ] This then allows the vm host to access that particular vlan The Problem We've noticed a few problems with this setup. One being that we currently create the interfaces manually. Which means if we add more vlan enabled interfaces and bridges we usually have to restart xend which is something I'm not so hot about. Also lower level staff have their heads melted by the number of interfaces and the risk of a mistake occurring is high. Secondly, it can take sometime for a host to come up if it has a number of vlan taged interfaces. Thirdly, its just not scaling well on the management aspects The Question Is there a better more flexible way to do this (in particular with Xen that ships with centos 5.3, 5.4 and 5.5 as we have to support all three) that leverages either scripting or other solutions to allow an arbitrary amount of interfaces to be created when a vm is instanced. Your advise and expertise is more that welcomed.

  Read the article

• Dell Latitude D510 Runs From Battery But Not AC Adapter

  - by Jason George

  I have a Dell Latitude D510 that went belly up around two years ago. It will run from the battery, however, the wall adapter will neither power the machine nor charge the battery. Once the battery is dead, the machine is dead. Since it died I've searched repeatedly for solutions. I've tried a new AC adapter and even removed and replaced the DC jack thinking one of the solder joints might be bad. Both to no avail. After two years of searching I finally found the answer today. Since it's such a simple fix and I had such a hard time finding it I wanted to post the info for others (as it is apparently a common issue with the D510). -----SOLUTION----- It seems this is commonly caused by a cracked solder joint at pin 1 on an inductor filter pair (FL2) near the power jack. Pins 1 and 4 are ground and pins 2 and 3 are power. There should be 20V from 1 to 2 and 3. Anything less indicates a cracked joint that is increasing resistance and dropping the supply voltage. Repair simply requires reflowing all four pins with a little added solder for security. Detailed instructions can be found here. Dell Latitude D510 solder problem

  Read the article

• Replacing DropBox with: Amazon S3 + SSL + GPG/TrueCrypt + Mounting on OSX ??

  - by Matt Rogish

  So, right now we're using DropBox to share various data files around between approximately 10 Mac OS X systems. However, we already have an S3 account and everyone on the lowest DropBox plan of $10/mo seems too expensive. So, I am contemplating something that would allow us to replace DropBox with our own home-grown solution. We are all fairly technical people and/or smart enough to follow some steps, so if it's not as "user friendly" as DropBox we're all comfortable with that. There are plenty of docs out there that have bits and pieces of what I want but some of the tools don't seem to fit the requirements: Transport security via SSL to the bucket Encryption of bucket contents Bi-directional syncing Most of the scripts I can find on the internet use "duplicity" which appears to fail #1 (it doesn't look like duplicity supports SSL to S3 - the docs don't state but the protocol looks plain old http http://www.nongnu.org/duplicity/duplicity.1.html#sect6 ) Many scripts use gpg to encrypt files. This seems like it could work, however I have to make sure that each OSX client is able to use the same key to encrypt and decrypt files (key management is left to me to manage). Finally, most of the scripts use one-way replication, e.g. using Amazon S3 as a simple backup store. As we'd be using Amazon S3 as the "repository" they fail this one. Whew. So, I'd love a single tool that does this but after an exhaustive search I don't think one exists. I'd be happy just knowing which tools out there can fulfill my 3 requirements, after that I can stitch together the rest. Any thoughts? THANKS!

  Read the article

• Why is the Windows 8 recycle bin using more space than it is allocated?

  - by oldmankit

  I ran WinDirStat to scan the contents of my hard drive. I was surprised to see that the $RECYCLE.BIN folder on my D: drive takes 26 GB of space. I emptied the recycle bin, refreshed the folder in WinDirStat, but it still takes 26 GB of space. I reduced the Maximum size of the recycle bin for this drive to 10000 MB for the main user of this computer, and disabled the recycle bin for the other user, and refreshed the folder in WinDirStat, but it still takes 26 GB of space. I ran (in an elevated window) rd /s D:\$Recycle.bin, and refreshed the folder in WinDirStat, and finally it became empty. Why was it taking up space even after I emptied it? Why was it taking more space (26 GB) than the maximum allowed amount (10 GB)? Update: After six months of using Windows (no re-install and no changes of settings related to the Recycle Bin) I used WinDirStat to check how big D:\$RECYCLE.BIN has become. It is now 29 GB. In Recycle Bin Properties, I select drive D, and it is still a custom maximum size (10000 MB).

  Read the article

• What is the quickest and safest way to test new software and revert all changes, if needed?

  - by calbar

  I'm looking for Windows software that will allow me to quickly create a "checkpoint", do whatever I might need to do to my computer - install programs/drivers/updates, create/delete personal files, reboot the system multiple times, open questionable attachments - and then revert the entire system back to when the checkpoint was created. Essentially I want Windows Restore Points that save my personal files and partitions, too. It sounds like disk imaging might be the ticket, but creating them is much too slow and the restore process too involved... I'm hoping to sacrifice full disaster recovery for speed. Creating a checkpoint should be as close to one-click as possible, and rolling back should be a matter of selecting a restore point and rebooting. Ding! I'm familiar with Sandboxie, True Image Home "Try and Decide", Returnil, and a number of other "virtual system" apps that actively "catch" changes and allow you to commit or reject them. I'm not interested in these for a number of reasons - I prefer the "cut and dry" restore point approach. Finally, I'll note that I've just recently become aware of Comodo Time Machine. It sounds absolutely perfect, however, a quick skim through the user forums show more than a few horror stories of corrupted, unbootable systems. Any positive personal experience with the software to suppress my superstitions, or suggestions for more established alternatives would be greatly appreciated - Comodo Time Machine seems relatively new. Thanks for your help!

  Read the article

• Scaling databases with cheap SSD hard drives

  - by Dennis Kashkin

  Hey guys! I hope that many of you are working with high traffic database-driven websites, and chances are that your main scalability issues are in the database. I noticed a couple of things lately: Most large databases require a team of DBAs in order to scale. They constantly struggle with limitations of hard drives and end up with very expensive solutions (SANs or large RAIDs, frequent maintenance windows for defragging and repartitioning, etc.) The actual annual cost of maintaining such databases is in $100K-$1M range which is too steep for me :) Finally, we got several companies like Intel, Samsung, FusionIO, etc. that just started selling extremely fast yet affordable SSD hard drives based on SLC Flash technology. These drives are 100 times faster in random read/writes than the best spinning hard drives on the market (up to 50,000 random writes per second). Their seek time is pretty much zero, so the cost of random I/O is the same as sequential I/O, which is awesome for databases. These SSD drives cost around $10-$20 per gigabyte, and they are relatively small (64GB). So, there seems to be an opportunity to avoid the HUGE costs of scaling databases the traditional way by simply building a big enough RAID 5 array of SSD drives (which would cost only a few thousand dollars). Then we don't care if the database file is fragmented, and we can afford 100 times more disk writes per second without having to spread the database across 100 spindles. . Is anybody else interested in this? I've been testing a few SSD drives and can share my results. If anybody on this site has already solved their I/O bottleneck with SSDs, I would love to hear your war stories! PS. I know that there are plenty of expensive solutions out there that help with scalability, for example the time proven RAM-based SANs. I want to be clear that even $50K is too expensive for my project. I have to find a solution that costs no more than $10K and does not take much time to implement.

  Read the article

• Server 2008 RAID 5 Write Speeds

  - by Solipsism

  I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

  Read the article

• Road Warrior VPN Setup

  - by wobblycogs

  I apologise up front for the rather open ended nature of this question but I've got well out of my depth and could really do with some pointers. I need to set up a road warrior VPN solution which will allow our customers to securely access a number of services we provide for them. Customer machines will be running a variety of Windows versions from XP onwards with a variety of patch levels. Typically they will connect from the clients main offices but not always. It is safe to assume that all clients will be behind NATs but we may occasionally see a connection that isn't NAT'ed. Typical connection situation is therefore: Customer Laptop -- Router (NAT) -- Internet -- VPN Server + Firewall -- Server (Win 2008 R2, Non-routable IP) There will initially be a dozen or so people that could connect but that will grow quickly to around 100. It's unlikely that we'll see that many concurrent connections though, I imagine our total VPN throughput would be <50Mbps peak. What are my options for setting this up? I've been trying to set up a system like this using a MikroTik router for a few days but have struggled to get it working correctly, particularly with NAT'ed clients. I've had a quick look at OpenVPN and liked what I saw but I think it's unlikely our customers IT departments would allow the client to be installed. Finally I've looked at the Cisco ASA range but I'm on a fairly tight budget so this is less preferable but it looks like it would work pretty much out of the box. My fall back position is to connect the server directly and use the provided VPN + Firewall facilities but that is far from ideal as the number of servers is likely to grow over time.

  Read the article

• Time Machine vs Source Control?

  - by Blub

  Finally got convinced to start using some kind of version control for my code instead of zipping down a copy of the project at the end of each day. Downloaded Tortoise SVN and used it to create a repository localy on my hdd. I've been using it for 2 days now but I have to say that using it is actually more hassle than just copying the project manually in explorer. Sure, you only store incremental changes but with the cheap disks of today I can't really say that's an argument when you only have small projects. I haven't realy found a quick way to browse the older versions of my files eighter. What I want is an infinite undo that is completely transparent while I code, if I save the file I want a backup. I don't want to check out, check in and don't even get me started on moving files. I haven't tried Time Machine for OS X but it looks like it's exactly what I'm looking for. Does such a program exist for windows? Preferably free and with some kind of tagging-system so I can tag a timestamp when the project is working etc. Maybe should add that I mostly work alone on a single computer. Update: Some of you asked why I want backup. Since I work alone it's mostly to allow me to quickly hack up a solution without worrying that something will screw up.

  Read the article

• Secure data from a server to a workstation using jumper hosts

  - by apalsson

  Hello. I have a WWW-server, my problem is that the content is sensitive and should not be accessible for people without proper credentials. How can I improve the ease of use but still maintain security following scenario; The Server is accessed through a "jumper host", i.e. the client connects to the jumper using VPN-connection and uses RemoteDesktop to access the jumper. From the jumper he uses RemoteDesktop again to access the Server. Finally on the Server the user can access content using a WWW-browser. All the way from the VPN-client to the WWW-browser requires authentication using a SmartCard-token. This seems quite secure to me. Content only gets mirrored on the RemoteDesktop between Server and jumper, no cached files to worry about. Connection between jumper and client is protected using VPN(ssl), so no eavesdropping. But it is quite cumbersome for the clients with many steps and connections to open. :( So, how can I improve the user experience accessing my server without compromising security? Thanks.

  Read the article

• How do I prevent my ASP .NET site from continually prompting for user credentials?

  - by gilles27

  I'm trying to get an ASP .NET website up and running on IIS6. The site will run in its own application pool, and uses Windows authentication, with anonymous access turned off. When I run the app pool under NETWORK SERVICE, everything works fine. However we need the app pool to run under a different account, because this account needs some extra privileges (we are printing Word documents). This new account is a member of the local users group, and the IIS_WPG group. It has also been granted the "Log on as a service right". When I browse to the site I am prompted for credentials, not once, but several times. When the page finally loads it looks wrong because the style sheets have not been applied. My suspicion is that I am being prompted once for each file (e.g. all the images, styles and script files) the browser requests, and that for some reason the website is unable to validate those credentials in order to serve the files back. If I allow anonymous access the page loads fine - we don't want to allow it but I mention it in case it offers any further clues. My theory is that perhaps the account the app pool runs under needs permissions to validate domain credentials? If that is so, how do I enable this?

  Read the article

• What is the difference between these Pentium Extreme Edition CPUs?

  - by Giffyguy

  The CPU in question is the Pentium Extreme Edition 955. Intel's website shows four "versions", but for the most part they all look identical. They even share the same set of ordering codes. But one of them has a substantially lower TDP, which is seemingly unexplainable - since everything else is the same. Two of them say "LGA775, Tray" and I have no idea what "Tray" means either. Also, two of them have a different SPEC code. What I need to know is: What does "LGA775, Tray" mean? Why does the one CPU have a lower TDP? And what does that mean for me? Does that mean lower maximum power consumption? Does it mean the CPU may be more stable/endurant, because of a lower heat output? Why do two of them have a different SPEC code, and what does this mean? Finally, what does PLGA775 (as opposed to LGA775) mean, and do I need to be worried about that? Information from Intel's wbsite: Intel® Pentium® Processor Extreme Edition 955 (4M Cache, 3.46 GHz, 1066 MHz FSB) with SPEC Code 1 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 95 Watts BX80553955 SL94N 2 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL94N 3 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 130 Watts BX80553955 SL8WM 4 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL8WM

  Read the article

• Why does the screen resolution of 1440x900 suddenly disappears from Intel GMA Control Panel?

  - by GeneQ

  I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2 . I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've Goggled that this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? Thanks. UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

  Read the article

• Multiheaded X.org with a single workspace-pool

  - by blauwblaatje

  I've got an idea for x.org/$randomwindowmanager in combination with a multiheaded setup, but I haven't figured out how it should work. Also I don't really know where to place the feature request. Now for the idea. I've been working with screen (wikipedia:GNU_Screen) for some years now. One thing I like about it, is the fact that I can get a multi-display mode (screen -x), so you can have multiple terminals all connected to the same screen. The fun thing about it, is that you can get 2 terminals with the same content and switch my onscreen layout, without moving the terminals. I admit, in screen it's not extremely useful, but I think for a wm it can be. Imagine this. You've got two monitors and 4 workdesks. On one workdesk I've got my IDE with code, on the second one I've got the output, on the third one I've got the documentation and on the forth one I've got my e-mail and IM clients. At one moment, I want my IDE and output on my monitors, another moment my code and documentation and Yet another moment my IM to consult a colleague and documentation or code. Finally my colleague comes to help me at my desk. I'd like it if we could both watch the same workdesk without him sitting on my lap, so I turn one monitor so he can see it better. It would be great if we could see the same thing that's on my monitor (exclude mousepointer). The thing with most WMs is that your workspaces on the two monitors are either separated or glued together. If they're separated, you can change workspaces on each monitor autonomous, but you can't exchange applications between monitors because they're different x-clients (iirc). If they're glued together (xinerama), you can exchange the applications, but when changing your workspace, the other monitors change too. So, what I'd like to know is this. Is this already possible or should I submit a feature request somewhere (and if so, where?)

  Read the article

• Failing to load rootfs: Ubuntu 10 + grub2 + rootfs ext4 w/ RAID1

  - by James

  I am having problems booting a new Ubuntu 10 (server) install. My primary HD (/dev/sda) is laid out as follows: Device Boot Start End Blocks Id System /dev/sda1 * 1 18 144553+ 83 Linux <-- /BOOT /dev/sda2 19 182401 1464991447+ 5 Extended /dev/sda5 19 2207 17583111 fd Linux raid autodetect /dev/sda6 2208 11934 78132096 fd Linux raid autodetect <-- / (ROOTFS) /dev/sda7 11935 182401 1369276146 fd Linux raid autodetect The rootfs is part of a RAID1 (software) array (currently degraded): # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md2 : active raid1 sda6[1] 78132032 blocks [2/1] [_U] The UUIDs for the partitions are as follows: # blkid /dev/sda1 /dev/sda1: UUID="b25dd301-41b9-4f4d-9b0a-0e31713dd74c" TYPE="ext2" # blkid /dev/sda6 /dev/sda6: UUID="af7b9ede-fa53-c0c1-74be-31ec752c5cd5" TYPE="linux_raid_member" # blkid /dev/md2 /dev/md2: UUID="a0602d42-6855-482f-870c-6f6ecdcdae3f" TYPE="ext4" Finally, I have my grub2 menuentry setup as follows: ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-25-server' --class ubuntu --class gnu-linux --class gnu --class os { insmod ext2 insmod raid insmod mdraid set root='(hd0,1)' search --no-floppy --fs-uuid --set b25dd301-41b9-4f4d-9b0a-0e31713dd74c linux /vmlinuz-2.6.32-25-server root=UUID=a0602d42-6855-482f-870c-6f6ecdcdae3f ro nosplash noplymouth initrd /initrd.img-2.6.32-25-server } When I attempt to boot, grub loads OK, however I eventually get the following error message: Gave up waiting for root device. ALERT /dev/disk/by-uuid/a0602d42-6855-482f-870c-6f6ecdcdae3f does not exist. Dropping to a shell! If from the grub bootloader I open a grub command line, I can ls (hd0,) and it lists the correct partitions with the UUIDs as shown above - sda6 shows 'a0602d42-6855-482f-870c-6f6ecdcdae3f' (the RAID UUID). If I ls (md2)/ it properly lists all the files on the RAID1 filesystem (ext4) so it doesn't appear to be an issue accessing the raid device. Does anyone have any suggestions as to what the problem might be? I can't figure this one out.

  Read the article

• How to sandbox a VMWare image as much as possible

  - by Craig H

  The situation: -A corporate environment, with a corporate managed XP desktop (locked down, patched regularly, restricted user rights, no manual install of SW, AV, etc.) The requirement: -Using VMWare Workstation, run a sandboxed image (also XP) for specific testing purposes (with admin rights in the guest VM). No network connectivity is required. It can't be a separate standalone physical workstation disconnected from the network. (FWIW, this is a legitimate, sanctioned requirement - not someone trying to get around corporate restrictions.) The challenge: -Do this in as safe/secure a manner as possible. The proposed solution: -Create an image with host-only networking. -Perhaps remove the virtual ethernet adapter? (not sure if it's required for basic VMWare functionality?) The question (finally): -What potential risks remain (and how could I best mitigate them)? One challenge is that the guest VM will not be a managed workstation itself, so patching, AV, etc. can't be guaranteed (and, ironically, would in fact be somewhat difficult given the proposed solution!)

  Read the article

• Mount an VHD on Mac OS X

  - by janm

  Is it possible (how) to mount an VHD file created by Windows 7 in OS X? I found some information about how to do this on linux. There is a fuse fs "vdfuse" which uses virtualbox libs to mount filesystems supported by virtualbox. However I was unable to compile the package on osx because nearly all headers are missing and I doubt that it would work anyway... EDIT #2: Okay I got my hands dirty and finally compiled vdfuse (http://forums.virtualbox.org/viewtopic.php?f=26&t=33355&start=0) on osx. As a starting point I used macfuse (http://code.google.com/p/macfuse/) and looked at the example file systems. This led me to the following build script infile=vdfuse.c outfile=vdfuse incdir="your/path/to/vbox/headers" INSTALL_DIR="/Applications/VirtualBox.app/Contents/MacOS" CFLAGS="-pipe" gcc -arch i386 "${infile}" \ "${INSTALL_DIR}"/VBoxDD.dylib \ "${INSTALL_DIR}"/VBoxDDU.dylib \ "${INSTALL_DIR}"/VBoxVMM.dylib \ "${INSTALL_DIR}"/VBoxRT.dylib \ "${INSTALL_DIR}"/VBoxDD2.dylib \ "${INSTALL_DIR}"/VBoxREM.dylib \ -o "${outfile}" \ -I"${incdir}" -I"/usr/local/include/fuse" \ -Wl,-rpath,"${INSTALL_DIR}" \ -lfuse_ino64 \ -Wall ${CFLAGS} You actually don't need to compile VirtualBox on your machine, just install a recent version of VirtualBox. So now I can partially mount vhds. The separate partitions appear as block files Partition1, Partition2, ... on my mount point. However Mac OS X does not include a loopback file system and macfuse's loopback fs does not work with block files, so we need a loopback fs to mount the blockfiles as actual partitions.

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Toshiba Satellite P755D USB 3.0 Drivers Missing - Windows 7 Professional

  - by nicorellius

  I bought a Toshiba Satellite P755D recently and installed Windows 7 Professional on the machine. It runs great. But I noticed the exclamation point in the yellow triangle icon in the Device Manager next to the Universal Serial Buss (USB) Controller (I'm assuming this is the USB 3.0 controller because mine doesn't recognize devices). Normally, when this kind of thing happens I go to the manufacturer's website and download appropriate drivers and call it a day. But not this time... I browsed to my model and found no driver for the USB 3.0 controller. I tried other HW and Utility drivers, thinking they would be bundled. No luck. I tried looking up the motherboard in my machine. Generic name, no luck. I then called Toshiba technical support and they tried basic troubleshooting, eg, uninstall device, reboot, for auto-installation; no luck. I popped the Windows 7 disk back in and tried to get information that way, no luck. Finally, the technical support guy said he would look into the engineer's system to see if there was a specific driver available and that's where I'm at. The technician told me that these USB 3.0 drivers come within the native driver pack in windows but that doesn't seem to be the case. Any ideas? EDIT - See attached screen shots.

  Read the article

• Understanding how IE's SmartScreen works

  - by Kevin Donn

  Today I downloaded an update to our mail server on my dev machine using IE9 on Win7 Pro. I directed IE to save the file on our server's shared drive so I could install it later. When the download finished, IE showed a red banner at the bottom and said that, ".exe is not commonly downloaded and could harm your computer." There were three buttons, "Delete", "Actions", and "View downloads". I selected "Actions" just because I had never seen this before. It showed a "SmartScreen Filter" dialog basically giving three choices: "Don't run this program (recommended)", "Delete program", and "Run anyway". I just canceled the dialog because I didn't want to run it in the first place; I just wanted to download it so I could run it later on the server. So when I did try to run it, it would blow up immediately saying, "Setup was unable to create the directory - Error 5: Access is denied." I tried unblocking the file, "Run as Administrator" even though I already was Administrator, turning off UAC, etc. Cutting to the chase, I finally downloaded the file again, ran WinMerge on the two and it showed they were identical, except the new one ran fine. I went back to my dev machine, downloaded the file through Firefox and then ran it on the server, again fine. But when I tried again through IE, again SmartScreen showed its red banner and somehow clobbered the file even though it was stored on another machine, and WinMerge can't tell the difference between it and a good file. I've looked around on the web for how SmartScreen works, but they all give user-level descriptions of it. What I want to know is, what does it do to that file to make it unrunnable on another machine? Thanks

  Read the article

• How do you gracefully upgrade mission critical systems to wildly disparate systems?

  - by Ernie

  In the span of the 12+ years of my career, I have yet to overcome this hurdle and I suspect the answer simply isn't easy or even possible, so I ask everyone here for their experience. Say that you're running into egregious problems that can only be fixed by moving from one platform to another - either from making a mistake in choosing the platform that was chosen years ago, or simply growing beyond what the system was originally designed for. You know for certain that the cruft that has built up over time will invariably mean that it will be nearly impossible to test for all the things that will certainly lead to tech support hell - which we all know leads to the loss of customers. Not that customers aren't already complaining about the egregious problems that already exist! The best possible way that I've discovered so far is to maybe devise a plan for the changeover, test it on a few clients, test it on a dozen clients, test it on a hundred clients, then finally finish the changeover for everyone and pray that you've worked out all the bugs with those first hundred and twenty, and that the animal by-products will not hit the ventilation system in the most spectacular fashion possible. However, that doesn't mean that it won't anyway. So say that you're moving from Exchange to Exim (or even just Sendmail to Exim). How do you handle it?

  Read the article

• Help with Ubuntu and Windows, separate HDs

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

  Read the article

• Configure a Windows PC as network appliance w/o monitor, keyboard and mouse

  - by Joshua Lim

  I intend to use a small form factor PC with Windows 7 Professional installed as a network appliance attached directly to my customer's LAN without connecting a monitor, keyboard or mouse. How should I configure the networking for my PC so that I can access it via say my laptop? I figure that I can do it 2 ways. Attach my laptop to the PC using a crossover cable? Connect via RDP and configure networking. Configure an IP address on the PC before I deliver it to the customer place. At the customer's place, attach the PC to LAN and connect to the IP address which I previously configured from my laptop or from one of the customer's workstations. I know the first way is doable, but is the second way possible? I'm sorry if this question sounds ridiculous - I am Delphi programmer but a novice on networking. Finally, if possible, I hope to make the configuration process web based as I wouldn't like to reveal the fact that I am using Win7 Pro for the network appliance!

  Read the article

• Getting the number of frames from a video in Android

  - by Jay Patel

  I want to get the number of frames from a video. I'm using the following code: package com.vidualtest; import java.io.File; import java.io.FileDescriptor; import android.app.Activity; import android.graphics.Bitmap; import android.media.MediaMetadataRetriever; import android.os.Bundle; import android.os.Environment; import android.widget.ImageView; public class VidualTestActivity extends Activity { /** Called when the activity is first created. */ File file; ImageView img; @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); img = (ImageView) findViewById(R.id.img); File sdcard = Environment.getExternalStorageDirectory(); file = new File(sdcard, "myvid.mp4"); MediaMetadataRetriever retriever = new MediaMetadataRetriever(); try { retriever.setDataSource(file.getAbsolutePath()); img.setImageBitmap(retriever.getFrameAtTime(10000,MediaMetadataRetriever.OPTION_CLOSEST)); } catch (IllegalArgumentException ex) { ex.printStackTrace(); } catch (RuntimeException ex) { ex.printStackTrace(); } finally { try { retriever.release(); } catch (RuntimeException ex) { } } } } In getFrameAtTime() I'm passing different static time values like 10000, 20000, etc. in milliseconds, but still I'm getting the same frame from the video. My goal is to get different frames with a different time interval.

  Read the article

• Delete on windows vista and seven -- discovery process

  - by M'vy

  Hi SUs! I've recently encountered a problem. Using svn at work I needed to clear some space. As you may know svn directories are full of sub-directories and files. So the delete process begins with a step of discovering the items to be deleted (I guess this is for displaying the progress bar). But in my case it ended up to be still running after I watched Braveheart (Off-topic: good film in my opinion. On-topic: and it last 2h50) and counting 440 000+ files. I finally decided to cut off the process and use the good old cmd with a del <directory> to do the job. (Done in some minutes) So I'm wondering if someone know how to override the system to make it actually begins the process while scanning the other items? At the end, I just want the file to be deleted and I don't care the number of files to be deleted. On the contrary I care about the time it takes. Thanks

  Read the article

< Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >