Search Results

Search found 5807 results on 233 pages for 'generic'.

Page 125/233 | < Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >

• Will BIOS boot mode Ubuntu install be able to boot when firmware "Fast Boot" is "Ultra Fast"?

  - by Pro Backup

  I have an AsRock mainboard with UEFI BIOS P1.50 02/14/2014. The firmware "Fast Boot" option is set to "Fast", Boot Option #1 is set to "AHCI P4: OCZ-VERT...": this is BIOS not UEFI boot. This boot disk has an MBR partitioning scheme (# parted -l | grep Partition\ Table:). Therefore Ubuntu 14.04 is installed in BIOS/CMS (Grub-PC) mode. The Ubuntu boot process ends in a text console (no GUI). There is no external graphics card in use. The stock Ubuntu kernel is replaced with Ubuntu supplied mainline 3.16.0-031600rc6-generic. dmesg outputs lines containing BIOS, like: SMBIOS 2.7 present Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored BIOS EDD facility v0.16 2004-Jun-25, 0 devices found The ASRock BIOS it selves display this help text for "Ultra Fast - Fast Boot": Ultra Fast mode is only supported by Windows 8 and the VBIOS must support UEFI GOP if you are using an external graphics card. Please notice that Ultra Fast mode will boot so fast that the only way to enter this UEFI Setup Utility is to Clear CMOS or run the Restart to UEFI utility in Windows. Assumptions: I suspect after changing UEFI setting "Fast Boot" to "Ultra Fast" that the machine will no longer boot into Ubuntu's console. I expect when first exchanging "Grub-pc" with "Grub-efi", that the machine will still be able to boot to a grub menu (thus allowing to change the "Fast Boot" setting back to "Fast" without clearing CMOS). Are these two "Fast Boot" assumptions correct, and/or, may I expect Ubuntu 14.04 running mainline kernel 3.16rc6 and Grub-efi to still boot to console after enabling UEFI Ultra Fast Boot?

  Read the article

• Laptop Charger Not Recognised Properly on Samsung NP900X3F

  - by user193732

  Firstly thanks for your time. Secondly, having an issue with my power charger on my Samsung Series 9 NP900X3F. When I boot into Ubuntu with the charger plugged in it recognises it as charging. When I unplug the charger after this it is still says it is charging. If I suspend in Ubuntu then plug/unplug during this suspended state it recognises it, but not during normal running. If I knew a little more I'm sure I could grab logs and find out what the difference between wake on suspend and normal running is, but alas I need help! I also am having issues with my keyboard backlight via the fn keys, but that I care about far less. Thank you very much. Linux mikey-900X3F 3.12.0-031200rc1-generic #201309161735 SMP Mon Sep 16 21:38:21 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux (I upgraded my kernel version to remove heinous horizontal artefacts I was getting) Happy to list more info about my system, ima bit of a noob. I did try searching however I can't find any questions at all about my system or related models with the same issue.

  Read the article

• Tweaking log4net Settings Programmatically

  - by PSteele

  A few months ago, I had to dynamically add a log4net appender at runtime.  Now I find myself in another log4net situation.  I need to modify the configuration of my appenders at runtime. My client requires all files generated by our applications to be saved to a specific location.  This location is determined at runtime.  Therefore, I want my FileAppenders to log their data to this specific location – but I won't know the location until runtime so I can't add it to the XML configuration file I'm using. No problem.  Bing is my new friend and returned a couple of hits.  I made a few tweaks to their LINQ queries and created a generic extension method for ILoggerRepository (just a hunch that I might want this functionality somewhere else in the future – sorry YAGNI fans): public static void ModifyAppenders<T>(this ILoggerRepository repository, Action<T> modify) where T:log4net.Appender.AppenderSkeleton { var appenders = from appender in log4net.LogManager.GetRepository().GetAppenders() where appender is T select appender as T;   foreach (var appender in appenders) { modify(appender); appender.ActivateOptions(); } } Now I can easily add the proper directory prefix to all of my FileAppenders at runtime: log4net.LogManager.GetRepository().ModifyAppenders<FileAppender>(a => { a.File = Path.Combine(settings.ConfigDirectory, Path.GetFileName(a.File)); }); Thanks beefycode and Wil Peck. Technorati Tags: .NET,log4net,LINQ

  Read the article

• Yoga Pro 2 Wi-Fi not working

  - by user293004

  I installed Ubuntu 14.04 on my new Yoga Pro 2 and the wireless is not working. It started with Windows 8 on it. The Network Manager says Wi-Fi is disabled by hardware switch. I tried putting a blacklist file in ect/modprobe.d as has been suggested in many places. I called the file "blacklist-ideapad_laptop.conf" and wrote in the file blacklist ideapad_laptop I checked to make sure that the wireless is enabled in the BIOS. It is. I ran rfkill list all and it displayed: 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes I ran iwlist wlan0 scan and it displayed: wlan0 Failed to read scan data : Network is down I ran sudo rmmod ideapad_laptop and it displayed: rmmod: ERROR: Module ideapad_laptop is not currently loaded. I ran ifconfig wlp1s0 up and it displayed: wlp1s0: ERROR while getting interface flags: No such device. I ran "lspci" and it displayed: 01:00.0 Network controller: Intel Corporation Wireless 7260 (rev 6b) I ran sudo lshw -c network and it displayed: *-network DISABLED description: Wireless interface product: Wireless 7260 vendor: Intel Corporation physical id: 0<br> bus info: pci@0000:01:00:0.0 logical name: wlan0 version: 6b serial: 7c:7a:91:5f:9b:fa width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-24-generic firmware=22.24.8.0 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:61 memory:b0400000-b0401fff This No wireless with Intel Centrino Advanced-N 7260 seems to be dealing with a similar issue. It suggests that I need to update my firmware. So I downloaded iwlwifi-7260-ucode-23.214.9.0 from Intel's website. I put the file "iwlwifi-7260-9.ucode" in /lib/firmware and ran "sudo lshw -c network" again. It displayed exactly as before. Is there something else I need to do install the new firmware?

  Read the article

• Initializing OpenFeint for Android outside the main Application

  - by Ef Es

  I am trying to create a generic C++ bridge to use OpenFeint with Cocos2d-x, which is supposed to be just "add and run" but I am finding problems. OpenFeint is very exquisite when initializing, it requires a Context parameter that MUST be the main Application, in the onCreate method, never the constructor. Also, the main Apps name must be edited into the manifest. I am trying to fix this. So far I have tried to create a new Application that calls my Application to test if just the type is needed, but you do really need the main Android application. I also tried using a handler for a static initialization but I found pretty much the same problem. Has anybody been able to do it? This is my working-but-not-as-intended code snippet public class DerpHurr extends Application{ @Override public void onCreate() { super.onCreate(); initializeOpenFeint("TestApp", "edthedthedthedth", "aeyaetyet", "65462"); } public void initializeOpenFeint(String appname, String key, String secret, String id){ Map<String, Object> options = new HashMap<String, Object>(); options.put(OpenFeintSettings.SettingCloudStorageCompressionStrategy, OpenFeintSettings.CloudStorageCompressionStrategyDefault); OpenFeintSettings settings = new OpenFeintSettings(appname, key, secret, id, options); //RIGHT HERE OpenFeint.initialize(***this***, settings, new OpenFeintDelegate() { }); System.out.println("OpenFeint Started"); } } Manifest <application android:debuggable="true" android:label="@string/app_name" android:name=".DerpHurr">

  Read the article

• How do I create a camera?

  - by Morphex

  I am trying to create a generic camera class for a game engine, which works for different types of cameras (Orbital, GDoF, FPS), but I have no idea how to go about it. I have read about quaternions and matrices, but I do not understand how to implement it. Particularly, it seems you need "Up", "Forward" and "Right" vectors, a Quaternion for rotations, and View and Projection matrices. For example, an FPS camera only rotates around the World Y and the Right Axis of the camera; the 6DoF rotates always around its own axis, and the orbital is just translating for a set distance and making it look always at a fixed target point. The concepts are there; implementing this is not trivial for me. SharpDX seems to have has already Matrices and Quaternions implemented, but I don't know how to use them to create a camera. Can anyone point me on what am I missing, what I got wrong? I would really enjoy if you could give a tutorial, some piece of code, or just plain explanation of the concepts.

  Read the article

• One of the partion on a usb harddisk cannot automount

  - by holmescn

  It is a very strange problem. My usb harddisk has four partitions, one is primary, the other three are logical (contained within an extended partition). When I plug in the disk, three of the partitions are mounted automatically except one--the first logical partition in the extended partition. Initially I thought it is the problem of system (at that time I used Mint). But after I change to Ubuntu 12.04, the problem wasn't solved. I don't want to add a rule in fstab, and I want to know what happened. The disk is fine, and the partition can be accessed in Windows and mounted manually. result of dmesg | tail: [100933.557649] usb 2-1.2: new high-speed USB device number 4 using ehci_hcd [100933.651891] scsi8 : usb-storage 2-1.2:1.0 [100934.649047] scsi 8:0:0:0: Direct-Access SAMSUNG PQ: 0 ANSI: 0 [100934.650963] sd 8:0:0:0: Attached scsi generic sg2 type 0 [100934.651342] sd 8:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [100934.651977] sd 8:0:0:0: [sdb] Write Protect is off [100934.651989] sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00 [100934.652836] sd 8:0:0:0: [sdb] No Caching mode page present [100934.652848] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.655354] sd 8:0:0:0: [sdb] No Caching mode page present [100934.655367] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.734652] sdb: sdb1 sdb3 < sdb5 sdb6 sdb7 > [100934.737706] sd 8:0:0:0: [sdb] No Caching mode page present [100934.737725] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.737731] sd 8:0:0:0: [sdb] Attached SCSI disk result of parted -l: Model: SAMSUNG (scsi) Disk /dev/sdb: 320GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 21.5GB 21.5GB primary ntfs 3 21.5GB 320GB 299GB extended lba 5 21.5GB 129GB 107GB logical ntfs 6 129GB 236GB 107GB logical ntfs 7 236GB 320GB 83.8GB logical ntfs

  Read the article

• how can I get 32-bit program to run on 64-bit Ubuntu?

  - by Carol

  Sorry to be asking this, but I have read quite a few posts and articles a lot of places wrt the issue I am having, to no avail. I am trying to get a Second Life Viewer (Firestorm) to run, and just keep getting the '64-bit error message' it throws. I have installed every 32-lib I can find, still doesn't work. I think I am surely missing some setting somewhere, or running Firestorm from the wrong place, or something, but I have no idea what. FWIW, Firestorm loads but doesn't behave right in the 32-bit version, either. I have actually tried several linux distros, 32 and 64-bit. Mint 32-bit runs it straight off, and Mint 64-bit throws the '64-bit error'. openSUSE, any version, won't run it at all. Oh, and all the other SL viewers I have tried behave the same way. I am beginning to wonder if my set-up just doesn't like linux. Here is my system info: CPU: Intel(R) Core(TM) i5 CPU 750 @ 2.67GHz (2661 MHz) Memory: 4026 MB OS Version: Linux 3.2.0-29-generic-pae #46-Ubuntu SMP Fri Jul 27 17:25:43 UTC 2012 i686 Graphics Card Vendor: ATI Technologies Inc. Graphics Card: ATI Radeon HD 5700 Series I appreciate any help anyone can give me! Thanks so much! Carol :)

  Read the article

• Trying to install Canon LBP7750Cdn driver on Ubuntu 12.04

  - by Gideon

  I'n new to Ubuntu/Linux and had significant difficulties while attempting to configure my printer to work. The automatic driver pairing wizard which Ubuntu uses to identify and install the appropriate drivers did not find my printer's driver. I managed to get it to print when I manually select the generic configuration and checked the PCL6 configuration. However, the printer driver wizard does provide a list of Canon printers and actually do specify my printer as LBP7750C (minus the "dn" at the end, I'm assuming its because duplex ability and networking is not present on all the models - I'm not sure if this could be the source of the problem), but in selecting this option and trying to print I receive this message: Idle - /usr/lib/cups/filter/foomatic-rip failed I searched for this similar problem which other users might have encountered, but while there where plenty of such cases, they all had different resolutions and were all related to HP printers. Canon actually do provide a driver for my printer, but it comes with no installation instructions unless you consider yourself an experienced CUPS guru. Seriously. If anyone can help me solve this foomatic-rip failed problem I'd be really grateful - and I'm sure many other folks too. [BTW, can't Canonical fix this type of thing for the next Ubuntu release? - I't seems like a small problem but it causes many problems and countles hours of production time loss.] Thanks in advance.

  Read the article

• What do you do to make sure you take proper/enough breaks, while avoiding unwanted side-effects of break taking?

  - by blueberryfields

  preamble It seems to me that computer programmers are one of a select few groups of people who actually take pleasure from sitting in front of computers for long periods of time. Most people in other professions actively dislike their time at computers, and do their best to avoid it (so, I assume, they don't have problems taking breaks). At least for me, having external cues for taking breaks, and clear instructions on what to do with each break (stretch, go for a walk, close my eyes, look into a distance of preferably a few km and focus on faraway objects, etc...), is a must. So far, I've just been making up the breaks and tools to get them as I go along, based on what looks to be low-specificity information found on the net (generic stuff ala ergonomics advice for office staff). This has led to all sorts of side effects - loss of attention as I get distracted if I walk around, breaks in flow with alarm clocks interrupting my thoughts, and people around me assuming I'm low on work due to the frequency of my walking around compared to everyone else. /preamble tl;dr Taking breaks is important My internal break taking system doesn't work, and ad-hoc ones have unwanted side effects What do you do to make sure you take proper breaks? How do you avoid unwanted side-effects, such as getting distracted or interrupting flow or giving your co-workers the impression you're spending a lot of time goofing off?

  Read the article

• Take care to unhook Anonymous Delegates

  - by David Vallens

  Anonymous delegates are great, they elimiante the need for lots of small classes that just pass values around, however care needs to be taken when using them, as they are not automatically unhooked when the function you created them in returns. In fact after it returns there is no way to unhook them. Consider the following code.   using System; using System.Collections.Generic; using System.Linq; using System.Text; using System.Diagnostics; namespace ConsoleApplication1 { class Program { static void Main(string[] args) { SimpleEventSource t = new SimpleEventSource(); t.FireEvent(); FunctionWithAnonymousDelegate(t); t.FireEvent(); } private static void FunctionWithAnonymousDelegate(SimpleEventSource t) { t.MyEvent += delegate(object sender, EventArgs args) { Debug.WriteLine("Anonymous delegate called"); }; t.FireEvent(); } } public class SimpleEventSource { public event EventHandler MyEvent; public void FireEvent() { if (MyEvent == null) { Debug.WriteLine("Attempting to fire event - but no ones listening"); } else { Debug.WriteLine("Firing event"); MyEvent(this, EventArgs.Empty); } } } } If you expected the anonymous delegates do die with the function that created it then you would expect the output Attempting to fire event - but no ones listeningFiring eventAnonymous delegate calledAttempting to fire event - but no ones listening However what you actually get is Attempting to fire event - but no ones listeningFiring eventAnonymous delegate calledFiring eventAnonymous delegate called In my example the issue is just slowing things down, but if your delegate modifies objects, then you could end up with dificult to diagnose bugs. A solution to this problem is to unhook the delegate within the function var myDelegate = delegate(){Console.WriteLine("I did it!");}; MyEvent += myDelegate; // .... later MyEvent -= myDelegate;

  Read the article

• 12.0.4.3 - Missing Battery Icon, auto Suspend not working, Keyboard shortcuts volume up/down no longer working

  - by Navraj

  Problems I am experiencing: Battery Icon not showing up unity bar (top right corner). Volume Up/Down/Mute not working. Bluetooth hot keys described above also not working.Brightness up/down keys on this keyboard no longer working (apple wireless keyboard) Laptop no longer suspends when lid is shut. I have to go to 'power' button on top right corner and click on 'Suspend' All was working flawlessly until I did the following: I have recently upgraded to Nvidia propriety driver version 319 {version recommended}. Installed Xscreensaver and then removed it and went back to default screensaver. Done a system update (1st since installing) and now currently running: Linux 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:19:35 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux NOTE: Base system was ubuntu 12.04.3 installed from ISO however lsb_release reports "No LSB modules are available" 4.installed psensor. I have check power setting (via Settings) and power setting via dconf-editor and set to recommended settings as described in posts detailing solution to this problem. - I have disabled 1) Nvdia settings at startup and 2) psensor at startup but this does not help. I am using an HP DV7 with 2GB Nvidia card. Not using any fancy graphics features. Recommendations? Thanks.

  Read the article

• Booting Error while using 12.04 booting from GRUB

  - by Paul Z.

  my name is Paul. I have encountered an issue relating to GRUB booting and the booting process in general. I have been running Ubuntu 12.04 LTS on my machine for quite a while. Before that, i had (before) 10.04, 11.04, 11.10, etc. I have been running Ubuntu, in general, but more specifically 12.04 for a long time with little to no problems. The problem: Earlier today, i was using my machine and then decided to take a little break. I shut down my machine (laptop, in case anyone was wondering) and left. Later, I came back ready to start it up and continue. I started it up and it took me to the Toshiba screen (like normal) then to the GRUB screen. I guessed that nothing was truly wrong, and chose the first option (something around the lines of: Ubuntu, with linux 3.22.0-35-generic). I waited for a bit and it still displayed the same purple screen. I restarted it and now chose the option like the first but with recovery at the end. Same result. Later, I waited longer and found that my computer came up with a bunch of lines of script. I waited longer but nothing new happened. What are your suggestions as to fix this problem? I will let my computer run overnight with the recovery setting and will let you know what the result is. Until then, please help. Thank you, your time and effort is greatly appreciated!

  Read the article

• Wireless drops on HP ENVY dv6 with RT3290 wireless, worked without problem prior to upgrading to Ubuntu 13.10, can it be fixed?

  - by Tim

  I have a HP ENVY dv6 Notebook PC with an AMD A10 quad core and RT3290 wireless. Since I upgraded from Ubuntu 13.04 to 13.10, the wireless connects, but then drops after a few minutes or longer, whether or not I am running openconnect to get through a VPN. If I attempt to run a remote X client (e.g. remote xterm) it drops. If I don't run an X client, it disconnects after a while, requiring a reload of the driver and reconnect. Wireless info... sudo lshw -c network *-network description: Wireless interface product: RT3290 Wireless 802.11n 1T/1R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 68:94:23:a7:09:cb width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.11.0-12-generic firmware=0.37 ip=192.168.1.115 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:55 memory:f0210000-f021ffff I have successfully built and installed the MediaTek driver with no luck on connecting, then the system hangs on reboot and I have to recover/undo the changes to boot successfully.

  Read the article

• dpkg error when using apt-get install

  - by V-T

  I upgraded to Ubuntu 14.04 from 12.04 and every time I use apt-get install for any package it ends with a bunch of errors about processing some of my latex packages. Including a snippet below: Sometimes, not accepting conffile updates in /etc/texmf/updmap.d causes updmap-sys to fail. Please check for files with extension .dpkg-dist or .ucf-dist in this directory dpkg: error processing package tex-common (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of lmodern: lmodern depends on tex-common (>= 3); however: Package tex-common is not configured yet. Reproduced by using sudo dpkg --configure -a and a total list of packages with this error is included here: Errors were encountered while processing: tex-common texlive-publishers tex-gyre texlive-latex-extra-doc texlive-fonts-extra-doc texlive-lang-english texlive-luatex texlive-generic-recommended texlive-pstricks-doc texlive-fonts-recommended latex2html latex-xcolor texlive-pictures texlive-fonts-extra texlive-pictures-doc asymptote texlive-bibtex-extra texlive-latex-recommended-doc texlive-latex-recommended doxygen-latex texlive-pstricks tipa texlive-latex-base texlive-fonts-recommended-doc latex-beamer texlive-font-utils texlive-latex-base-doc texlive-latex-extra texlive-extra-utils texlive texlive-publishers-doc lmodern Any ideas on how to fix this?

  Read the article

• Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

  - by Tim

  Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

  Read the article

• browser without gpu support

  - by manuzhang

  Google has an Easter egg that draws 3D graph but when I tried it out on chrome it complained about no WebGL support. I've also tested it on Firefox whose WebGL support was enabled but ended up with the same problem. Thus, I suspect it's an issue of my GPU. Some googling led me to chrome://gpu and here's what I got Graphics Feature Status Canvas: Software only, hardware acceleration unavailable HTML Rendering: Software only, hardware acceleration unavailable 3D CSS: Unavailable. Hardware acceleration unavailable WebGL: Unavailable. Hardware acceleration unavailable WebGL multisampling: Unavailable. Hardware acceleration unavailable Problems Detected GPU process was unable to boot. Access to GPU disallowed. GL driver is software rendered. Accelerated compositing is disabled.: 59302 Mesa drivers in linux older than 7.11 are assumed to be buggy. Accelerated 2d canvas is unstable in Linux at the moment. Version Information Data exported Tue Apr 10 2012 18:35:57 GMT+0800 (CST) Chrome version 18.0.1025.151 (Official Build 130497) Operating system Linux 3.0.0-0300-generic Software rendering list version 1.27 ANGLE revision 988 2D graphics backend Skia I wonder what each of the problem implies and How I may properly deal with it? I'm using Ubuntu 11.04

  Read the article

• Access functions from user control without events?

  - by BornToCode

  I have an application made with usercontrols and a function on main form that removes the previous user controls and shows the desired usercontrol centered and tweaked: public void DisplayControl(UserControl uControl) I find it much easier to make this function static or access this function by reference from the user control, like this: MainForm mainform_functions = (MainForm)Parent; mainform_functions.DisplayControl(uc_a); You probably think it's a sin to access a function in mainform, from the usercontrol, however, raising an event seems much more complex in such case - I'll give a simple example - let's say I raise an event from usercontrol_A to show usercontrol_B on mainform, so I write this: uc_a.show_uc_b+= (s,e) => { usercontrol_B uc_b = new usercontrol_B(); DisplayControl(uc_b); }; Now what if I want usercontrol_B to also have an event to show usercontrol_C? now it would look like this: uc_a.show_uc_b+= (s,e) => { usercontrol_B uc_b = new usercontrol_B(); DisplayControl(uc_b); uc_b.show_uc_c += (s2,e2) => {usercontrol_C uc_c = new usercontrol_C(); DisplayControl(uc_c);} }; THIS LOOKS AWFUL! The code is much simpler and readable when you actually access the function from the usercontrol itself, therefore I came to the conclusion that in such case it's not so terrible if I break the rules and not use events for such general function, I also think that a readable usercontrol that you need to make small adjustments for another app is preferable than a 100% 'generic' one which makes my code look like a pile of mud. What is your opinion? Am I mistaken?

  Read the article

• CodePlex learns to talk to other services!

  CodePlex is now able to talk to other services! For example, if you want CodePlex to tell Trello to update cards on your Trello board, it can do it. Or if you want CodePlex to notify your Campfire chat room when updates are pushed, it can do that too. To start off, we are going to be adding support for the following services: Campfire – Notify a Campfire chat room when commits occur HipChat – Notify a HipChat chat room when commits occur Trello – Add commit summaries to Trello cards by referencing those cards in commit messages Twitter – Notify your Twitter followers when updates are pushed to your project In addition, we will continue to support our existing integrations with Windows Azure – Continuously deploy to Windows Azure on pushes (For Git and Hg projects) AppHarbor – Continuously deploy to AppHarbor on pushes To set up these integrations for your project, navigate to the project settings page as a project coordinator, and click on the services section as seen below:   While we are starting with these six services, the infrastructure is now in place to allow us to quickly roll out new integrations. We would love to hear which services and integrations you would like to see most on our suggestions page. We realize that there are some services and URLs that only make sense for your project to send notifications to. To support this scenario, we plan to add generic web hooks in the near future. Have ideas on how to improve CodePlex? Please visit our suggestions page! Vote for existing ideas or submit a new one. As always you can reach out to the CodePlex team on Twitter @codeplex or reach me directly @Rick_Marron.    

  Read the article

• Correct nvidia+intel graphics setup in 14.04

  - by Espressofa

  Just upgraded to 14.04 to try to fix some other issues. Now, something has gone wrong with my graphics. I have a Thinkpad T530 with Intel and Nvidia graphics cards. $ inxi -SGx System: Host: xyz Kernel: 3.13.0-24-generic x86_64 (64 bit, gcc: 4.8.2) Desktop: N/A Distro: Ubuntu 14.04 trusty Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller bus-ID: 00:02.0 Card-2: NVIDIA GF108M [NVS 5400M] bus-ID: 01:00.0 X.Org: 1.15.1 drivers: fbdev,vesa,intel,nouveau (unloaded: nvidia) Resolution: [email protected] GLX Renderer: N/A GLX Version: N/A Direct Rendering: N/A $ glxinfo name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". I'm not sure what I did but now something is wrong with my graphics, as should be visible from the above commands. nvidia-detector says "none" as well. I used to have bumblebee but then some website said to remove it and now something's clearly wrong. What's the right way to set things up? Should I try to add bumblebee back? Here's what's installed now: $ dpkg --get-selections | grep nvidia nvidia-319 install nvidia-331 install nvidia-libopencl1-331 install nvidia-opencl-icd-331 install nvidia-prime install nvidia-settings install nvidia-settings-319 install

  Read the article

• 14.04 LTS Unity no longer boots after last 94 MB update

  - by Harryg123

  I am running 14.04 LTS, Unity, on an HP Pavillion 15, 4GBRAM, 750 GB hdd, I-5 machine, with AMD 8600M graphics card built in. I have disabled the dash and all Ubuntu spyware. I have been faithfully loading all updates as they appear. This morning it asked for a 94 MB update (bringing kernel to .27, I think. Now, I can boot, get to login screen, but it freezes after that. Keyboard doesn't work at that point, but mouse does. I booted into recovery mode, tried to run in generic graphics mode, -- system again froze. I also pressed [esc] during boot, but saw nothing strange; then text disappeared and was replaced by login screen. I am not a hobbyist; this is a production machine and I have a lot of work to do today. Having a standard software update render my machine completely useless... sigh. Perhaps the simplest thing to do would be to revert to the previous configuration. How do I do that? I can boot into recovery mode. But I have no idea how to proceed. TIA for all help. -Harry

  Read the article

• Lexmark E240 printing issues

  - by NoamH

  I have Lexmark E240 laser printer. I have been using it with 12.04 (32bit) for 2 years with no significant issues. Since lexmark does not support this printer on linux, I used alternatives drivers that were suggested by the community, such as HP-lasterjet, E238, generic PS, etc. They all worked fine, more or less. After upgrading to 14.04 (64bit fresh install) I tried to configure the printer as before, but now I have problems. The test page is ok, but when printing, most of the times, the first page in the document will be printed very partially and in 300% zoom. Next page might be ok. If I turn off the printer and back on, the first page might be ok, but in the next print job, it will be broken again. I used all the above printer options. Same results. I did NOT install the lexmark drivers since they are intended for 12.04 and the package manager report that it is in "bad quality" (don't know why). Does anyone has any experience with this printer in 14.04 64bit ?

  Read the article

• How can I use timer to stop another thread? [on hold]

  - by Haoda Fu

  How can we stop another thread based on a timer? I was trying to use timer to stop another thread. But I didn't got a success. To better illustrate my point and for your easy to understand the key issue. I made the following sample example. Your help is really appreciated using System; using System.Collections.Generic; using System.Text; using System.Threading; using System.Timers; namespace TestCodes { public static class Program { private static Thread nT = new Thread(PrintABC); private static System.Timers.Timer aTimer; public static void Main() { aTimer = new System.Timers.Timer(1000); aTimer.Elapsed += TimerCallback; aTimer.Interval = 1000; aTimer.Enabled = true; nT.Start(); Console.ReadLine(); } private static void TimerCallback(Object o, ElapsedEventArgs e) { nT.Join(); Console.WriteLine("Complete the PrintABC"); GC.Collect(); } private static void PrintABC() { for (int iter = 1; iter < 300; iter++) { Console.WriteLine(iter+"abc"); Console.ReadKey(); //Thread.Sleep(100); } } } }

  Read the article

• Choppy USB mice on just one of USB ports

  - by user20532

  I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

  Read the article

• hdmi audio works only with aplay -D alsa test wavs; open source radeon drivers; kernel 3.5 vgaswitcheroo

  - by user108754

  I've trolled the internets to make hdmi work on my system Ubuntu 12.04 software center kernel 3.5 uname: Linux ubuntu 3.5.0-18-generic #29~precise1-Ubuntu SMP...x86_64 x86_64 x86_64 GNU/Linux open source radeon drivers vgaswitcheroo (hybrid intel/radeon gpu): I boot with intel, not radeon, running. (and recall that with kernel 3.5, vgaswitcheroo now gives info on a third item, "DIS-Audio"; it indicates pwr on my system) ( /etc/rc.local: chown user:user /sys/kernel/debug/ # change "username" with your user name echo OFF /sys/kernel/debug/vgaswitcheroo/switch ) grub indeed now has "radeon.audio=1" for testing audio, I did aplay -l which gave me the card and device, which made me try aplay -D plughw:1,3 /usr/share/sounds/alsa/Front_Center.wav and lo! I get crystal clear sound on my hdtv. If I play an mp3 file as the argument to that command, I get noise as, I guess, aplay interprets the mp3 code as a wav. If I play a .wav that is not in the /usr/share/sounds/alsa/ directory, I get nothing. Internet flash video in browser plays no sound over hdmi. Both system sounds control and pavucontrol have hdmi cedar selected. Alas, I can not get sound for any gui test (left, right). Why would only aplay, and only when directed with "-D plughw", yield sound over hdmi? I've also tried only using one sound program at a time, if it was a limitation of alsa, so I tried aplay with web browser and even the sound control gui closed. I tried each of the last two, running alone. No improvement. alsamixer only shows hda intel and I think it's only the intel audio, not the hdmi.

  Read the article

< Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >