Search Results

Search found 3312 results on 133 pages for 'freebsd ports'.

Page 126/133 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

• Why won't USB 3.0 external hard drive run at USB 3.0 speeds?

  - by jgottula

  I recently purchased a PCI Express x1 USB 3.0 controller card (containing the NEC USB 3.0 controller) with the intent of using a USB 3.0 external hard drive with my Linux box. I installed the card in an empty PCIe slot on my motherboard, connected the card to a power cable, strung a USB 3.0 cable between one of the new ports and my external HDD, and connected the HDD to a wall socket for power. Booting the system, the drive works 100% as intended, with the one exception of throughput: rather than using SuperSpeed 4.8 Gbps connectivity, it seems to be falling back to High Speed 480 Mbps USB 2.0-style throughput. Disk Utility shows it as a 480 Mbps device, and running a couple Disk Utility and dd benchmarks confirms that the drive fails to exceed ~40 MB/s (the approximate limit of USB 2.0), despite it being an SSD capable of far more than that. When I connect my USB 3.0 HDD, dmesg shows this: [ 3923.280018] usb 3-2: new high speed USB device using ehci_hcd and address 6 where I would expect to find this: [ 3923.280018] usb 3-2: new SuperSpeed USB device using xhci_hcd and address 6 My system was running on kernel 2.6.35-25-generic at the time. Then, I stumbled upon this forum thread by an individual who found that a bug, which was present in kernels prior to 2.6.37-rc5, could be the culprit for this type of problem. Consequently, I installed the 2.6.37-generic mainline Ubuntu kernel to determine if the problem would go away. It didn't, so I tried 2.6.38-rc3-generic, and even the 2.6.38 nightly from 2010.02.01, to no avail. In short, I'm trying to determine why, with USB 3.0 support in the kernel, my USB 3.0 drive fails to run at full SuperSpeed throughput. See the comments under this question for additional details. Output that might be relevant to the problem (when booting from 2.6.38-rc3): Relevant lines from dmesg: [ 19.589491] xhci_hcd 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 19.589512] xhci_hcd 0000:03:00.0: setting latency timer to 64 [ 19.589516] xhci_hcd 0000:03:00.0: xHCI Host Controller [ 19.589623] xhci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 12 [ 19.650492] xhci_hcd 0000:03:00.0: irq 17, io mem 0xf8100000 [ 19.650556] xhci_hcd 0000:03:00.0: irq 47 for MSI/MSI-X [ 19.650560] xhci_hcd 0000:03:00.0: irq 48 for MSI/MSI-X [ 19.650563] xhci_hcd 0000:03:00.0: irq 49 for MSI/MSI-X [ 19.653946] xHCI xhci_add_endpoint called for root hub [ 19.653948] xHCI xhci_check_bandwidth called for root hub Relevant section of sudo lspci -v: 03:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30) Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f8100000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] #18 Kernel driver in use: xhci_hcd Kernel modules: xhci-hcd Relevant section of sudo lsusb -v: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.38-020638rc3-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:03:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled Full, non-verbose lsusb: Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 003: ID 04d9:0702 Holtek Semiconductor, Inc. Bus 009 Device 002: ID 046d:c068 Logitech, Inc. G500 Laser Mouse Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 006: ID 174c:5106 ASMedia Technology Inc. Bus 003 Device 004: ID 0bda:0151 Realtek Semiconductor Corp. Mass Storage Device (Multicard Reader) Bus 003 Device 002: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 006: ID 1687:0163 Kingmax Digital Inc. Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 046d:081b Logitech, Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Full output: full dmesg full lspci full lsusb

  Read the article

• Using FFmpeg in c#?

  - by daniel

  So i know its a fairly big challenge but i want to write a basic movie player/converter in c# using the FFmpeg library. However the first obstacle i need to overcome is wrapping the FFmpeg library in c#. I downloaded ffmpeg but couldn't compile it on windows, so i downloaded a precompiled version for me. Ok awesome. Then i started looking for c# wrappers. I have looked around and have found a few wrappers such as SharpFFmpeg (http://sourceforge.net/projects/sharpffmpeg/) and ffmpeg-sharp (http://code.google.com/p/ffmpeg-sharp/). First of all i wanted to use ffmpeg-sharp as its LGPL and SharpFFmpeg is GPL. However it had quite a few compile errors. Turns out it was written for the mono compiler, i tried compiling it with mon but couldn't figure out how. I then started to manually fix the compiler errors myself, but came across a few scary ones and thought i'd better leave those alone. So i gave up on ffmpeg-sharp. Then i looked at SharpFFmpeg and it looks like what i want, all the functions P/Invoked for me. However its GPL? Both the AVCodec.cs and AVFormat.cs files look like ports of avcodec.c and avformat.c which i reckon i could port myself? Then not have to worry about licencing. But i wan't to get this right before i go ahead and start coding. Should I: Write my own c++ library for interacting with ffmpeg, then have my c# program talk to the c++ library in order to play/convert videos etc. OR Port avcodec.h and avformat.h (is that all i need?) to c# by using a whole lot of DllImports and write it entirely in c#? First of all consider that i'm not great at c++ as i rarely use it but i know enough to get around. The reason i'm thinking #1 might be the better option is that most FFmpeg tutorials are in c++ and i'd also have more control over memory management that if i was to do it in c#. What do you think? Also would you happen to have any usefull links (perhaps a tutorial) for using FFmpeg? EDIT: spelling mistakes

  Read the article

• How to send email from an EC2 instance using GoDaddy's SMTP server?

  - by Matt Greer

  SMTP is a whole new ballgame for me, but I am reading up on it. I am attempting to send email from my EC2 instance using GoDaddy's SMTP server. My domain name is registered through GoDaddy and I have 2 email accounts with them. I can successfully send the email from my dev box no problem. my web.config <system.net> <mailSettings> <smtp from="[email protected]" deliveryMethod="Network"> <network host="smtpout.secureserver.net" clientDomain="mydomain.com" port="25" userName="[email protected]" password="mypassword" defaultCredentials="false" /> </smtp> </mailSettings> </system.net> In my ASP.NET app: MailMessage mailMessage = new MailMessage("[email protected]", recipientEmail, emailSubject, body); mailMessage.IsBodyHtml = false; SmtpClient mailClient = new SmtpClient(); mailClient.Send(mailMessage); Very typical, simple use of System.Net.Mail.SmtpClient. The mail client is picking up the settings from my web.config as expected. From the EC2 instance, the same setup yields: System.Net.Mail.SmtpException: Failure sending mail. ---> System.IO.IOException: Unable to read data from the transport connection: net_io_connectionclosed. at System.Net.Mail.SmtpReplyReaderFactory.ProcessRead(Byte[] buffer, Int32 offset, Int32 read, Boolean readLine) at System.Net.Mail.SmtpReplyReaderFactory.ReadLines(SmtpReplyReader caller, Boolean oneLine) at System.Net.Mail.SmtpReplyReaderFactory.ReadLine(SmtpReplyReader caller) at System.Net.Mail.SmtpConnection.GetConnection(ServicePoint servicePoint) at System.Net.Mail.SmtpClient.Send(MailMessage message) --- End of inner exception stack trace --- I have searched high and low and not found anyone else attempting this. All GoDaddy smtp situations I have found involve people being hosted by GoDaddy using their relay server. Some more info: My EC2 instance is Windows Server 2008 with IIS 7. The app is running in .NET 4 I can successfully use Gmail's SMTP server on the EC2 instance by using their port, setting SmtpClient.EnableSsl to true, and sending the mail through a gmail account. But we want to send the email from an account on our domain. I have port 25 open on both the Windows firewall and Amazon's Security group based firewall. I have played with Wireshark and noticed my SMTP related traffic was talking to ports in the 5,000s, so out of desperation I opened them all up to no avail (then closed them back down) As far as I know my EC2 instance's IP address is not black listed by GoDaddy. I have a feeling I'm just missing something fundamental. I also have a feeling someone is going to recommend I use AuthSmtp or something similar, I'll agree, and have had wasted the past 6 hours :)

  Read the article

• Log4r : logger inheritance, yaml configuration, alternatives ?

  - by devlearn

  Hello, I'm pretty new to ruby environments and I was looking for a nice logging framework to use it my ruby and rails applications. In my previous experiences I have successfully used log4j and log4p (the perl port) and was expecting the same level of usability (and maturity) with log4r. However I must say that there are a number of things that are not clear at all in the log4r framework. 1 Logger Inheritance The logger inheritance does not seem to be managed at all ! If I declare a logger named 'myapp' and then try to get a logger name 'myapp::engine', the lookup will end with a NameError. I would expect that the framework returns the root logger according to the naming scheme and to use the 'myapp' logger. Q1 : Of course I can work around this and manage the names by myself with a lookup method, however is there a cleaner way to do this without any extra coding ? 2 YAML configuration Second thing that confuses me is the yaml configuration. On the log4r site there are literally no information about this system, the doc links forward to missing pages, so all the info I can find about is contained in the examples directory of the gem. I was pretty confused with the fact that the yaml configuration must contain the pre_config section, and that I need to define my own levels. If I remove the pre_config secion, or replace all the “custom” levels by the standard ones ( debug, info, warn, fatal ) , the example will throw the following error : log4r/yamlconfigurator.rb:68:in `decode_yaml': Log level must be in 0..7 (ArgumentError) So there seems to be no way of using a simple file where we only declare the loggers and appenders for the framework. Q2 : I realy think that I missed something and that must be a way of providing a simple yaml conf file. Do you have any examples of such an usage ? 3 Variables substitution in XML file Q3 : The Yaml configuration system seems to provide such a feature however I was unable to find a similar feature with XML files. Any ideas ? 4 Alternatives ? I must say that I'm very disappointed by the feature level and the maturity of log4r compared to the log4j and other log4j ports. I run into this framework with a solid background of logging APIs in other languages and find myself working around in all kinds just to make 'basic things' running in a “real world application”. By that I mean a complex application composed of several gems, console/scripting apps, and a rails web front end where the configuration must be mutualized and where we make intensive usage of namespaces and inheritance. I've run several searches in order to find something more suitable or mature, but did not find anything similar. Q4 : Do you guys know any (serious) alternatives to log4r framework that could be used in a enterprise class app ? Thanks reading all of this ! I'd really appreciate any pointers, Kind Regards,

  Read the article

• XML Socket and Regular Socket in Flash/Flex does not send message immediately.

  - by kramer

  I am trying to build a basic RIA where my Flex application client opens an XML socket, sends the xml message "people_list" to server, and prints out the response. I have ruby at the server side and I have successfully set up the security policy stuff. The ruby xml server, successfully accepts the connections from Flex, successfully detects when they are closed and can also send messages to client. But; there is a problem... It cannot receive messages from flex client. The messages sent from flex client are queued and sent as one package when the socket is closed. Therefore, the whole wait-for-request-then-reply thing is not working... This is also -kinda- mentioned in the XMLSocket.send() document, where it is stated that the messages are sent async so; they may be delivered at any time in future. But; I need them to be synced, flushed or whatever. This is the server side code: require 'socket' require 'observer' class Network_Reader_Ops include Observable @@reader_listener_socket = UDPSocket.new @@reader_broadcast_socket = UDPSocket.new @@thread_id def initialize @@reader_broadcast_socket.setsockopt(Socket::SOL_SOCKET, Socket::SO_BROADCAST, 1) @@reader_broadcast_socket.setsockopt(Socket::SOL_SOCKET, Socket::SO_REUSEADDR, 1) @@reader_listener_socket.setsockopt(Socket::SOL_SOCKET, Socket::SO_REUSEADDR, 1) @@reader_broadcast_socket.bind('', 50050) @@reader_listener_socket.bind('', 50051) @@thread_id = Thread.start do loop do begin text, sender = @@reader_listener_socket.recvfrom_nonblock 1024 print("Knock response recived: ", text) notify_observers text rescue Errno::EAGAIN retry rescue Errno::EWOULDBLOCK retry end end end end def query @@reader_broadcast_socket.send("KNOCK KNOCK", 0, "255.255.255.255", 50050) end def stop Thread.kill @@thread_id end end class XMLSocket_Connection attr_accessor :connection_id def update (data) connection_id.write(data+"\0") end end begin # Set EOL for Flash $/ = '\x00' xml_socket = TCPServer.open('', '4444') security_policy_socket = TCPServer.open('', '843') xml_socket.setsockopt(Socket::SOL_SOCKET, Socket::SO_REUSEADDR, 1) security_policy_socket.setsockopt(Socket::SOL_SOCKET, Socket::SO_REUSEADDR, 1) a = Thread.start do network_ops = nil loop { accepted_connection = xml_socket.accept print(accepted_connection.peeraddr, " is accepted\n") while accepted_connection.gets incoming = $_.dump print("Received: ", incoming) if incoming == "<request>readers on network</request>" then network_ops = Network_Reader_Ops.new this_con = XMLSocket_Connection.new this_con.connection_id = accepted_connection network_ops.add_observer this_con network_ops.query end end if not network_ops.nil? then network_ops.delete_observer this_con network_ops.stop network_ops = nil end print(accepted_connection, " is gone\n") accepted_connection.close } end b = Thread.start do loop { accepted_connection = security_policy_socket.accept Thread.start do current_connection = accepted_connection while current_connection.gets if $_ =~ /.*policy\-file.*/i then current_connection.write("<cross-domain-policy><allow-access-from domain="*" to-ports="*" /></cross-domain-policy>\0") end end current_connection.close end } end a.join b.join rescue puts "FAILED" retry end And this is the flex/flash client side code: UPDATE: I have also tried using regular socket and calling flush() method but; the result was same. private var socket:XMLSocket = new XMLSocket(); protected function stopXMLSocket():void { socket.close(); } protected function startXMLSocket():void { socket.addEventListener(DataEvent.DATA, dataHandler); socket.connect(xmlSocketServer_address, xmlSocketServer_port); socket.send("<request>readers on network</request>"); } protected function dataHandler(event:DataEvent):void { mx.controls.Alert.show(event.data); } How do I achieve the described behaviour?

  Read the article

• Using FFmpeg in .net?

  - by daniel

  So i know its a fairly big challenge but i want to write a basic movie player/converter in c# using the FFmpeg library. However the first obstacle i need to overcome is wrapping the FFmpeg library in c#. I downloaded ffmpeg but couldn't compile it on windows, so i downloaded a precompiled version for me. Ok awesome. Then i started looking for c# wrappers. I have looked around and have found a few wrappers such as SharpFFmpeg (http://sourceforge.net/projects/sharpffmpeg/) and ffmpeg-sharp (http://code.google.com/p/ffmpeg-sharp/). First of all i wanted to use ffmpeg-sharp as its LGPL and SharpFFmpeg is GPL. However it had quite a few compile errors. Turns out it was written for the mono compiler, i tried compiling it with mon but couldn't figure out how. I then started to manually fix the compiler errors myself, but came across a few scary ones and thought i'd better leave those alone. So i gave up on ffmpeg-sharp. Then i looked at SharpFFmpeg and it looks like what i want, all the functions P/Invoked for me. However its GPL? Both the AVCodec.cs and AVFormat.cs files look like ports of avcodec.c and avformat.c which i reckon i could port myself? Then not have to worry about licencing. But i wan't to get this right before i go ahead and start coding. Should I: Write my own c++ library for interacting with ffmpeg, then have my c# program talk to the c++ library in order to play/convert videos etc. OR Port avcodec.h and avformat.h (is that all i need?) to c# by using a whole lot of DllImports and write it entirely in c#? First of all consider that i'm not great at c++ as i rarely use it but i know enough to get around. The reason i'm thinking #1 might be the better option is that most FFmpeg tutorials are in c++ and i'd also have more control over memory management than if i was to do it in c#. What do you think? Also would you happen to have any usefull links (perhaps a tutorial) for using FFmpeg? EDIT: spelling mistakes

  Read the article

• .NET SerialPort DataReceived event thread interference with main thread

  - by Kiran

  I am writing a serial communication program using the SerialPort class in C# to interact with a strip machine connected via a RS232 cable. When i send the command to the machine it responds with some bytes depending on the command. Like when i send a "\D" command, i am expecting to download the machine program data of 180 bytes as a continous string. As per the machine's manual, it suggests as a best practice to send an unreognized characters like comma (,) character to make sure the machine is initialized before sending the first command in the cycle. My serial communication code is as follows: public class SerialHelper { SerialPort commPort = null; string currentReceived = string.Empty; string receivedStr = string.Empty; private bool CommInitialized() { try { commPort = new SerialPort(); commPort.PortName = "COM1"; if (!commPort.IsOpen) commPort.Open(); commPort.BaudRate = 9600; commPort.Parity = System.IO.Ports.Parity.None; commPort.StopBits = StopBits.One; commPort.DataBits = 8; commPort.RtsEnable = true; commPort.DtrEnable = true; commPort.DataReceived += new SerialDataReceivedEventHandler(commPort_DataReceived); return true; } catch (Exception ex) { return false; } } void commPort_DataReceived(object sender, SerialDataReceivedEventArgs e) { SerialPort currentPort = (SerialPort)sender; currentReceived = currentPort.ReadExisting(); receivedStr += currentReceived; } internal int CommIO(string outString, int outLen, ref string inBuffer, int inLen) { receivedStr = string.Empty; inBuffer = string.Empty; if (CommInitialized()) { commPort.Write(outString); } System.Threading.Thread.Sleep(1500); int i = 0; while ((receivedStr.Length < inLen) && i < 10) { System.Threading.Thread.Sleep(500); i += 1; } if (!string.IsNullOrEmpty(receivedStr)) { inBuffer = receivedStr; } commPort.Close(); return inBuffer.Length; } } I am calling this code from a windows form as follows: len = SerialHelperObj.CommIO(",",1,ref inBuffer, 4) len = SerialHelperObj.CommIO(",",1,ref inBuffer, 4) If(inBuffer == "!?*O") { len = SerialHelperObj.CommIO("\D",2,ref inBuffer, 180) } A valid return value from the serial port looks like this: \D00000010000000000010 550 3250 0000256000 and so on ... I am getting some thing like this: \D00000010D,, 000 550 D,, and so on... I feel that my comm calls are getting interferred with the one when i send commands. But i am trying to make sure the result of the comma command then initiating the actual command. but the received thread is inserting the bytes from the previous communication cycle. Can any one please shed some light into this...? I lost quite some hair just trying to get this work. I am not sure where i am doing wrong

  Read the article

• BindException with INTERNET permission requested

  - by Mondain

  I have seen several questions regarding SocketException when using Android, but none of them cover the BindException that I get even with the INTERNET permission specified in my manifest. Here is part of my manifest: <uses-permission android:name="android.permission.INTERNET"></uses-permission> <uses-permission android:name="android.permission.ACCESS_NETWORK_STATE"></uses-permission> <uses-permission android:name="android.permission.ACCESS_WIFI_STATE"></uses-permission> <uses-permission android:name="android.permission.READ_OWNER_DATA"></uses-permission> <uses-permission android:name="android.permission.READ_PHONE_STATE"></uses-permission> <uses-permission android:name="android.permission.ACCOUNT_MANAGER"></uses-permission> <uses-permission android:name="android.permission.AUTHENTICATE_ACCOUNTS"></uses-permission> Here is the relevant portion of my LogCat output: 04-22 14:49:06.117: DEBUG/MyLibrary(4844): Address to bind: 192.168.1.14 port: 843 04-22 14:49:06.197: WARN/System.err(4844): java.net.BindException: Permission denied (maybe missing INTERNET permission) 04-22 14:49:06.207: WARN/System.err(4844): at org.apache.harmony.luni.platform.OSNetworkSystem.socketBindImpl(Native Method) 04-22 14:49:06.207: WARN/System.err(4844): at org.apache.harmony.luni.platform.OSNetworkSystem.bind(OSNetworkSystem.java:107) 04-22 14:49:06.217: WARN/System.err(4844): at org.apache.harmony.luni.net.PlainSocketImpl.bind(PlainSocketImpl.java:184) 04-22 14:49:06.217: WARN/System.err(4844): at java.net.ServerSocket.bind(ServerSocket.java:414) 04-22 14:49:06.227: WARN/System.err(4844): at org.apache.harmony.nio.internal.ServerSocketChannelImpl$ServerSocketAdapter.bind(ServerSocketChannelImpl.java:213) 04-22 14:49:06.227: WARN/System.err(4844): at java.net.ServerSocket.bind(ServerSocket.java:367) 04-22 14:49:06.237: WARN/System.err(4844): at org.apache.harmony.nio.internal.ServerSocketChannelImpl$ServerSocketAdapter.bind(ServerSocketChannelImpl.java:283) 04-22 14:49:06.237: WARN/System.err(4844): at mylibrary.net.PolicyConnection$PolicyServerWorker.(PolicyConnection.java:201) I Really hope this is a simple problem and not something complicated by the fact that the binding is occurring within a worker thread on a port less than 1024. Update Looks as if this is a privileged port issue, anyone know how to bind to ports lower than 1024 in Android? SelectorProvider provider = SelectorProvider.provider(); try { ServerSocketChannel channel = provider.openServerSocketChannel(); policySocket = channel.socket(); Log.d("MyLibrary", "Address to bind: " + device.getAddress().getAddress() + " port: 843"); InetSocketAddress addr = new InetSocketAddress(InetAddress.getByName(device.getAddress().getAddress()), 843); policySocket.bind(addr); policySocket.setReuseAddress(true); policySocket.setReceiveBufferSize(256); } catch (Exception e) { e.printStackTrace(); }

  Read the article

• Adding Parsekit To An Xcode Project

  - by Garry

  I am trying to add the Parsekit framework to my OSX Xcode project. I've never added a 3rd party framework before and I can't get it to work right. I dragged the included Xcode project into my 'Groups & Files' pane and chose to Add it to my project. I then dragged Parsekit.framework underneath the Link Binary With Libraries heading. Then I double-clicked my target app and added Parsekit as a Direct Dependency. I also added libicucore.dylib as a Linked Library (as it says to do this on their site). Finally, in the Build settings tab of my target info I set the Header Search Paths to /Users/path/to/include/directory and the Other Linker Flags to -ObjC -all_load. Running this as a debug build work fine with no errors. However, when I build my app to release and then try to run the executable created, the app fails to load with the following error message: MyApp cannot be opened because of a problem. Check with the developer to make sure myApp works with this version of Mac OS X. Here is the dump from the crash reporter: Process: MyApp [11658] Path: /Users/Garry/Programming/Xcode/Mac/MyApp/build/Release/MyApp.app/Contents/MacOS/MyApp Identifier: com.yourcompany.MyApp Version: ??? (???) Code Type: X86-64 (Native) Parent Process: launchd [135] Date/Time: 2010-05-24 17:08:08.475 +0100 OS Version: Mac OS X 10.6.3 (10D573) Report Version: 6Interval Since Last Report: 133300 sec Crashes Since Last Report: 3 Per-App Crashes Since Last Report: 3 Anonymous UUID: DF0265E4-B5A0-45E1-8B71-D52A27CFDDCA Exception Type: EXC_BREAKPOINT (SIGTRAP) Exception Codes: 0x0000000000000002, 0x0000000000000000 Crashed Thread: 0 Dyld Error Message: Library not loaded: @executable_path/../Frameworks/ParseKit.framework/Versions/A/ParseKit Referenced from: /Users/Garry/Programming/Xcode/Mac/MyApp/build/Release/MyApp.app/Contents/MacOS/MyApp Reason: image not found Model: MacBookPro5,5, BootROM MBP55.00AC.B03, 2 processors, Intel Core 2 Duo, 2.53 GHz, 4 GB, SMC 1.47f2 Graphics: NVIDIA GeForce 9400M, NVIDIA GeForce 9400M, PCI, 256 MB Memory Module: global_name AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8D), Broadcom BCM43xx 1.0 (5.10.91.27) Bluetooth: Version 2.3.1f4, 2 service, 2 devices, 1 incoming serial ports Network Service: AirPort, AirPort, en1 Network Service: Ethernet Adaptor (en6), Ethernet, en6 Serial ATA Device: Hitachi HTS545025B9SA02, 232.89 GB Serial ATA Device: HL-DT-ST DVDRW GS23N USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8507, 0x24400000 USB Device: Internal Memory Card Reader, 0x05ac (Apple Inc.), 0x8403, 0x26500000 USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x04500000 USB Device: Apple Internal Keyboard / Trackpad, 0x05ac (Apple Inc.), 0x0237, 0x04600000 USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x06100000 USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8213, 0x06110000 After building the app, in addition to the executable file, Xcode is also creating a file called MyApp.app.dSYM. Any idea what that is?? I am developing with Xcode 3.2.2 on an Intel MBP running 10.6.3. Many thanks for any help offered.

  Read the article

• Problem connecting to postgres with Kohana 3 database module on OS X Snow Leopard

  - by Bart Gottschalk

  Environment: Mac OS X 10.6 Snow Leopard PHP 5.3 Kohana 3.0.4 When I try to configure and use a connection to a postgresql database on localhost I get the following error: ErrorException [ Warning ]: mysql_connect(): [2002] No such file or directory (trying to connect via unix:///var/mysql/mysql.sock) Here is the configuration of the database in /modules/database/config/database.php (note the third instance named 'pgsqltest') return array ( 'default' => array ( 'type' => 'mysql', 'connection' => array( /** * The following options are available for MySQL: * * string hostname * string username * string password * boolean persistent * string database * * Ports and sockets may be appended to the hostname. */ 'hostname' => 'localhost', 'username' => FALSE, 'password' => FALSE, 'persistent' => FALSE, 'database' => 'kohana', ), 'table_prefix' => '', 'charset' => 'utf8', 'caching' => FALSE, 'profiling' => TRUE, ), 'alternate' => array( 'type' => 'pdo', 'connection' => array( /** * The following options are available for PDO: * * string dsn * string username * string password * boolean persistent * string identifier */ 'dsn' => 'mysql:host=localhost;dbname=kohana', 'username' => 'root', 'password' => 'r00tdb', 'persistent' => FALSE, ), 'table_prefix' => '', 'charset' => 'utf8', 'caching' => FALSE, 'profiling' => TRUE, ), 'pgsqltest' => array( 'type' => 'pdo', 'connection' => array( /** * The following options are available for PDO: * * string dsn * string username * string password * boolean persistent * string identifier */ 'dsn' => 'mysql:host=localhost;dbname=pgsqltest', 'username' => 'postgres', 'password' => 'dev1234', 'persistent' => FALSE, ), 'table_prefix' => '', 'charset' => 'utf8', 'caching' => FALSE, 'profiling' => TRUE, ), ); And here is the code to create the database instance, create a query and execute the query: $pgsqltest_db = Database::instance('pgsqltest'); $query = DB::query(Database::SELECT, 'SELECT * FROM test')->execute(); I'm continuing to research a solution for this error but thought I'd ask to see if someone else has already found a solution. Any ideas are welcome. One other note is that I know my build of PHP can access this postgresql db since I'm able to manage the db using phpPgAdmin. But I have yet to determine what phpPgAdmin is doing differently to connect to the db than what Kohana 3 is attempting. Bart

  Read the article

• Binary socket and policy file in Flex

  - by Daniil

  Hi, I'm trying to evaluate whether Flex can access binary sockets. Seems that there's a class calles Socket (flex.net package). The requirement is that Flex will connect to a server serving binary data. It will then subscribe to data and receive the feed which it will interpret and display as a chart. I've never worked with Flex, my experience lies with Java, so everything is new to me. So I'm trying to quickly set something simple up. The Java server expects the following: DataInputStream in = ..... byte cmd = in.readByte(); int size = in.readByte(); byte[] buf = new byte[size]; in.readFully(buf); ... do some stuff and send binary data in something like out.writeByte(1); out.writeInt(10000); ... etc... Flex, needs to connect to a localhost:6666 do the handshake and read data. I got something like this: try { var socket:Socket = new Socket(); socket.connect('192.168.110.1', 9999); Alert.show('Connected.'); socket.writeByte(108); // 'l' socket.writeByte(115); // 's' socket.writeByte(4); socket.writeMultiByte('HHHH', 'ISO-8859-1'); socket.flush(); } catch (err:Error) { Alert.show(err.message + ": " + err.toString()); } The first thing is that Flex does a <policy-file-request/>. I've modified the server to respond with: <?xml version="1.0"?> <!DOCTYPE cross-domain-policy SYSTEM "/xml/dtds/cross-domain-policy.dtd"> <cross-domain-policy> <site-control permitted-cross-domain-policies="master-only"/> <allow-access-from domain="192.168.110.1" to-ports="*" /> </cross-domain-policy> After that - EOFException happens on the server and that's it. So the question is, am I approaching whole streaming data issue wrong when it comes to Flex? Am I sending the policy file wrong? Unfortunately, I can't seem to find a good solid example of how to do it. It seems to me that Flex can do binary Client-Server application, but I personally lack some basic knowledge when doing it. I'm using Flex 3.5 in IntelliJ IDEA IDE. Any help is appreciated. Thank you!

  Read the article

• ImageMagick on Mac OSX Snow Leopard. Is there any way to get it to work?

  - by ?????

  It seems that I have more trouble getting standard Unix things to run on Snow Leopard than any other platform--including Windows cygwin For the past couple of days, I've been trying to get ImageMagick to run on Snow Leopard. The most obvious way, Mac Ports, fails: tppllc-Mac-Pro:ImageMagick-sl swirsky$ sudo port install imagemagick ---> Computing dependencies for p5-locale-gettext ---> Configuring p5-locale-gettext Error: Target org.macports.configure returned: configure failure: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_perl_p5-locale-gettext/work/gettext-1.05" && /opt/local/bin/perl Makefile.PL INSTALLDIRS=vendor " returned error 2 Command output: checking for gettext... no checking for gettext in -I/opt/local/include -arch i386 -L/opt/local/lib -lintl...gettext function not found. Please install libintl at Makefile.PL line 18. no Error: Unable to upgrade port: 1 Error: Unable to execute port: upgrade xorg-libXt failed Before reporting a bug, first run the command again with the -d flag to get complete output. tppllc-Mac-Pro:ImageMagick-sl swirsky$ Not wanting to spend another two days figuring out why my libintl doesn't have a "gettext" function, I tried a different route: the script mentioned here: http://github.com/masterkain/ImageMagick-sl This script downloads and installs an ImageMagic independently of MacPorts issues tppllc-Mac-Pro:ImageMagick-sl swirsky$ /usr/local/bin/convert dyld: Library not loaded: /opt/local/lib/libiconv.2.dylib Referenced from: /opt/local/lib/libfontconfig.1.dylib Reason: Incompatible library version: libfontconfig.1.dylib requires version 8.0.0 or later, but libiconv.2.dylib provides version 7.0.0 Trace/BPT trap It downloads everything and compiles fine, but fails when I try to run it, with the message above. So now I'm two steps away from ImageMagick, trying to get a newer libiconv on my machine. I downloaded the latest libiconv, compiled and built it. I put the resulting library in /opt/local/lib, and I still get the same error message: tppllc-Mac-Pro:.libs swirsky$ sudo mv libiconv.2.dylib /opt/local/lib/libiconv.2.dylib tppllc-Mac-Pro:.libs swirsky$ convert dyld: Library not loaded: /opt/local/lib/libiconv.2.dylib Referenced from: /opt/local/lib/libfontconfig.1.dylib Reason: Incompatible library version: libfontconfig.1.dylib requires version 8.0.0 or later, but libiconv.2.dylib provides version 7.0.0 Trace/BPT trap So here's my question: Is it possible to get ImageMagick to run on OSX Snow Leopard? Are there any binary distributions that have static libraries baked in so I don't have to worry about these issue/

  Read the article

• How to call a JavaScript function from one frame to another in Chrome/Webkit with file protocol

  - by bambax

  I have developed an application that has a list of items in one frame; when one clicks on an item it does something in another frame (loads an image). This used to work fine in all browsers, including Chrome 3; now it still works fine in Firefox but in recent versions of Chrome (I believe since 4) it throws this error: Unsafe JavaScript attempt to access frame with URL (...) from frame with URL (...). Domains, protocols and ports must match. This is obviously a security "feature" but is it possible to get around it? Here is a simple test: index.html: <html> <frameset cols="50%,50%"> <frame src="left.html" name="left"/> <frame src="right.html" name="right"/> </frameset> </html> left.html: <html> <body> <a href="javascript:parent.right.test('hello');">click me</a> </body> </html> right.html: <html> <body> <script> function test(msg) { alert(msg); } </script> </body> </html> The above works in Firefox 3.6 and Chrome 3 but in Chrome 5 it throws the above error... Edit: added the @cols attribute to the frameset element in fact it works in Chrome if and only if the pages are served with the http protocol (and from the same domain) but my problem is when pages are local and served from a file:// protocol. Then it works in Firefox (all versions) and Chrome 3 but not Chrome 5 (I don't have Chrome 4 so I'm not shure about that specific version (and don't know if it's even possible to download a specific Chrome version?) -- but for Chrome 5 I'm very sure it doesn't work).

  Read the article

• ImageMagick on Mac OSX Snow Leopard. Is there any way to get it to compile and run?

  - by ?????

  It seems that I have more trouble getting standard Unix things to run on Snow Leopard than any other platform--including Windows cygwin For the past couple of days, I've been trying to get ImageMagick to run on Snow Leopard. The most obvious way, Mac Ports, fails: tppllc-Mac-Pro:ImageMagick-sl swirsky$ sudo port install imagemagick ---> Computing dependencies for p5-locale-gettext ---> Configuring p5-locale-gettext Error: Target org.macports.configure returned: configure failure: shell command " cd "/opt/local/var/macports/build/_opt_local_var_macports_sources_rsync.macports.org_release_ports_perl_p5-locale-gettext/work/gettext-1.05" && /opt/local/bin/perl Makefile.PL INSTALLDIRS=vendor " returned error 2 Command output: checking for gettext... no checking for gettext in -I/opt/local/include -arch i386 -L/opt/local/lib -lintl...gettext function not found. Please install libintl at Makefile.PL line 18. no Error: Unable to upgrade port: 1 Error: Unable to execute port: upgrade xorg-libXt failed Before reporting a bug, first run the command again with the -d flag to get complete output. tppllc-Mac-Pro:ImageMagick-sl swirsky$ Not wanting to spend another two days figuring out why my libintl doesn't have a "gettext" function, I tried a different route: the script mentioned here: http://github.com/masterkain/ImageMagick-sl This script downloads and installs an ImageMagic independently of MacPorts issues tppllc-Mac-Pro:ImageMagick-sl swirsky$ /usr/local/bin/convert dyld: Library not loaded: /opt/local/lib/libiconv.2.dylib Referenced from: /opt/local/lib/libfontconfig.1.dylib Reason: Incompatible library version: libfontconfig.1.dylib requires version 8.0.0 or later, but libiconv.2.dylib provides version 7.0.0 Trace/BPT trap It downloads everything and compiles fine, but fails when I try to run it, with the message above. So now I'm two steps away from ImageMagick, trying to get a newer libiconv on my machine. I downloaded the latest libiconv, compiled and built it. I put the resulting library in /opt/local/lib, and I still get the same error message: tppllc-Mac-Pro:.libs swirsky$ sudo mv libiconv.2.dylib /opt/local/lib/libiconv.2.dylib tppllc-Mac-Pro:.libs swirsky$ convert dyld: Library not loaded: /opt/local/lib/libiconv.2.dylib Referenced from: /opt/local/lib/libfontconfig.1.dylib Reason: Incompatible library version: libfontconfig.1.dylib requires version 8.0.0 or later, but libiconv.2.dylib provides version 7.0.0 Trace/BPT trap Now here's something interesting. The error message shows it's looking in /opt/local/lib/libiconv.2.dylib. otools -L shows that this does implement 8.0.0: tppllc-Mac-Pro:.libs swirsky$ otool -L /opt/local/lib/libiconv.2.dylib /opt/local/lib/libiconv.2.dylib: /usr/local/lib/libiconv.2.dylib (compatibility version 8.0.0, current version 8.0.0) /usr/lib/libSystem.B.dylib (compatibility version 1.0.0, current version 125.0.0) tppllc-Mac-Pro:.libs swirsky$ And, for good measure, I set the DYLD_LIBRARY_PATH to make sure this directory is the one for dynamic libraries. So even though I do have a library that provides 8.0.0, it's being seen as 7.0.0! Any ideas why this would happen? So here's my question: Is it possible to get ImageMagick to run on OSX Snow Leopard? Are there any binary distributions that have static libraries baked in so I don't have to worry about these issue/

  Read the article

• C# Detect Localhost Port Usage

  - by ThaKidd

  In advance, thank you for your advice. I am currently working on a program which uses Putty to create a SSH connection with a server that uses local port forwarding to enable a client, running my software, to access the service behind the SSH server via localhost. IE: client:20100 - Internet - Remote SSH server exposed via router/firewall - Local Intranet - Intranet Web POP3 Server:110. Cmd Line: "putty -ssh -2 -P 22 -C -L 20100:intranteIP:110 -pw sshpassword sshusername@sshserver" Client would use putty to create a SSH connection with the SSH server specifying in the connection string that it would like to tie port 110 of the Intranet POP3 Server to port 20100 on the client system. Therefore the client would be able to open up a mail client to localhost:20100 and interact with the Internal POP3 server over the SSH tunnel. The above is a general description. I already know what I am trying to do will work without a problem so am not looking for debate on the above. The question is this...How can I ensure the local port (I cannot use dynamic ports, so it must be static) on localhost is not being used or listened to by any other application? I am currently executing this code in my C# app: private bool checkPort(int port) { try { //Create a socket on the current IPv4 address Socket TestSocket = new Socket(AddressFamily.InterNetwork, SocketType.Stream, ProtocolType.Tcp); // Create an IP end point IPEndPoint localIP = new IPEndPoint(IPAddress.Parse("127.0.0.1"), port); // Bind that port TestSocket.Bind(localIP); // Cleanup TestSocket.Close(); return false; } catch (Exception e) { // Exception occurred. Port is already bound. return true; } } I am currently calling this function starting with a specific port in a for loop to get the 'false' return at the first available port. The first port I try is actually being listened to by uTorrent. The above code does not catch this and my connection fails. What is the best method to ensure a port is truly free? I do understand some other program may grab the port during/after I have tested it. I just need to find something that will ensure it is not currently in use AT ALL when the test is executed. If there is a way to truly reserve the localhost port during the test, I would love to hear about it.

  Read the article

• FILE_NOT_FOUND when trying to open COM port C++

  - by Moutabreath

  I am trying to open a com port for reading and writing using C++ but I can't seem to pass the first stage of actually opening it. I get an INVALID_HANDLE_VALUE on the handle with GetLastError FILE_NOT_FOUND. I have searched around the web for a couple of days I'm fresh out of ideas. I have searched through all the questions regarding COM on this website too. I have scanned through the existing ports (or so I believe) to get the name of the port right. I also tried combinations of _T("COM1") with the slashes, without the slashes, with colon, without colon and without the _T I'm using windows 7 on 64 bit machine. this is the code i got I'll be glad for any input on this void SendToCom(char* data, int len) { DWORD cbNeeded = 0; DWORD dwPorts = 0; EnumPorts(NULL, 1, NULL, 0, &cbNeeded, &dwPorts); //What will be the return value BOOL bSuccess = FALSE; LPCSTR COM1 ; BYTE* pPorts = static_cast<BYTE*>(malloc(cbNeeded)); bSuccess = EnumPorts(NULL, 1, pPorts, cbNeeded, &cbNeeded, &dwPorts); if (bSuccess){ PORT_INFO_1* pPortInfo = reinterpret_cast<PORT_INFO_1*>(pPorts); for (DWORD i=0; i<dwPorts; i++) { //If it looks like "COMX" then size_t nLen = _tcslen(pPortInfo->pName); if (nLen > 3) { if ((_tcsnicmp(pPortInfo->pName, _T("COM"), 3) == 0) ){ COM1 =pPortInfo->pName; //COM1 ="\\\\.\\COM1"; HANDLE m_hCommPort = CreateFile( COM1 , GENERIC_READ|GENERIC_WRITE, // access ( read and write) 0, // (share) 0:cannot share the COM port NULL, // security (None) OPEN_EXISTING, // creation : open_existing FILE_FLAG_OVERLAPPED, // we want overlapped operation NULL // no templates file for COM port... ); if (m_hCommPort==INVALID_HANDLE_VALUE) { DWORD err = GetLastError(); if (err == ERROR_FILE_NOT_FOUND) { MessageBox(hWnd,"ERROR_FILE_NOT_FOUND",NULL,MB_ABORTRETRYIGNORE); } else if(err == ERROR_INVALID_NAME) { MessageBox(hWnd,"ERROR_INVALID_NAME",NULL,MB_ABORTRETRYIGNORE); } else { MessageBox(hWnd,"unkown error",NULL,MB_ABORTRETRYIGNORE); } } else{ WriteAndReadPort(m_hCommPort,data); } } pPortInfo++; } } } }

  Read the article

• OpenVPN: Connection established but can’t connect to server

  - by Maik

  I am trying to set up OpenVPN to allow me to connect a number of laptops to my network in a way that allows the laptops to connect to specific computers via HTTP (to e.g. a server management page) and windows shares (to access files) In the test environment my laptops live in a network with a 192.168.1.X address range. The host-network has a 10.66.77.X address range The server hosting the OpenVPN server has address 10.77.10.20. I need to access some application server web pages on this machine, accessible on various ports The server with the windows shares as well as some other web based pages I need to access is on address 10.66.77.20 The config files for server and laptop are attached below. The laptop establishes the VPN connection without problems, but I cannot access any of the machines, even a simple ping fails. Maybe a routing problem? The routing table for the laptop is shown below as well - every idea is appreciated! Thanks! Maik Server config file port 1194 dev tun tls-server ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/projects.crt key /etc/openvpn/keys/projects.key dh /etc/openvpn/keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 10.66.77.0 255.255.255.0" keepalive 10 60 inactive 600 route 10.8.0.1 255.255.255.0 user openvpn group openvpn persist-tun persist-key verb 4 client config file dev tun proto udp remote SERVERADDR 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert accountingLaptop.crt key accountingLaptop.key ns-cert-type server comp-lzo verb 3 Resulting routing table on client laptop C:\Documents and Settings\User>route print =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 23 5a 9b 64 9b ...... Atheros AR8132 PCI-E Fast Ethernet Controller - Packet Scheduler Miniport 0x3 ...00 24 2c 35 c9 6b ...... Dell Wireless 1395 WLAN Mini-Card - Packet Sched uler Miniport 0x4 ...00 ff 5e 03 43 9b ...... TAP-Win32 Adapter V9 - Packet Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.129 25 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 1 10.8.0.4 255.255.255.252 10.8.0.6 10.8.0.6 30 10.8.0.6 255.255.255.255 127.0.0.1 127.0.0.1 30 10.66.77.0 255.255.255.0 10.8.0.5 10.8.0.6 1 10.255.255.255 255.255.255.255 10.8.0.6 10.8.0.6 30 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.129 192.168.1.129 25 192.168.1.129 255.255.255.255 127.0.0.1 127.0.0.1 25 192.168.1.255 255.255.255.255 192.168.1.129 192.168.1.129 25 224.0.0.0 240.0.0.0 10.8.0.6 10.8.0.6 30 224.0.0.0 240.0.0.0 192.168.1.129 192.168.1.129 25 255.255.255.255 255.255.255.255 10.8.0.6 2 1 255.255.255.255 255.255.255.255 10.8.0.6 10.8.0.6 1 255.255.255.255 255.255.255.255 192.168.1.129 192.168.1.129 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None

  Read the article

• Getting hp-snmp-agents on HP ProLiant DL360 on Lenny working

  - by mark

  After receiving our HP ProLiant DL360 I'd like to integrate the machine into our Munin system and thus enable ProLiant specific information to be exposed via SNMP. I'm running Debian Lenny with kernel 2.6.26-2-vserver-amd64 . I've followed http://downloads.linux.hp.com/SDR/getting_started.html and the HP repository has been added to /etc/apt/sources.list.d/HP-ProLiantSupportPack.list . Setting up Lenny SNMP itself is not a problem, I configure it to have a public v1 community string to read all data and it works. I install hp-snmp-agents and run hpsnmpconfig and it adds additional lines to the top of /etc/snmp/snmpd.conf : dlmod cmaX /usr/lib64/libcmaX64.so snmpd gets restarted. Via lsof I can see that libcmaX64 was loaded and is used by snmpd, put I do not get any additional information out of snmp. I use snmpwalk -v 1 -c public ... and I can see many OIDs but I do not see the new ones I'd expect, most notably temperatures, fan speed and such. The OIDs I'm expecting are e.g. 1.3.6.1.4.1.232.6.2.6.8.1.4.1 , this is from the existing munin plugins from http://exchange.munin-monitoring.org/plugins/snmp__hp_temp/version/1 . snmpd[19007]: cmaX: Parsing shared as a type was unsucessful snmpd[19007]: cmaX: listening for subagents on port 25375 snmpd[19007]: cmaX: subMIB 1 handler has disconnected snmpd[19007]: cmaX: subMIB 2 handler has disconnected snmpd[19007]: cmaX: subMIB 3 handler has disconnected snmpd[19007]: cmaX: subMIB 5 handler has disconnected snmpd[19007]: cmaX: subMIB 6 handler has disconnected snmpd[19007]: cmaX: subMIB 8 handler has disconnected snmpd[19007]: cmaX: subMIB 9 handler has disconnected snmpd[19007]: cmaX: sent ColdStarts on ports 25376 to 25393 snmpd[19007]: cmaX: subMIB 10 handler has disconnected snmpd[19007]: cmaX: subMIB 11 handler has disconnected snmpd[19007]: cmaX: subMIB 14 handler has disconnected snmpd[19007]: cmaX: subMIB 15 handler has disconnected snmpd[19007]: cmaX: subMIB 16 handler has disconnected snmpd[19007]: cmaX: subMIB 21 handler has disconnected snmpd[19007]: cmaX: subMIB 22 handler has disconnected snmpd[19007]: cmaX: subMIB 23 handler has disconnected snmpd[19007]: cmaX: subMIB 1 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 2 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 3 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 5 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 6 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 8 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 9 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 10 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 11 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 14 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 15 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 16 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 21 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 22 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 23 will be sent on port 25376 to hp Advanced Server Management_Peer snmpd[19007]: cmaX: subMIB 18 handler has disconnected snmpd[19007]: cmaX: subMIB 18 will be sent on port 25393 to cpqnicd snmpd[19007]: NET-SNMP version 5.4.1 This doesn't look particular bad for me, it's just informational I guess. I've compared the walking OID output with and without the module and there's no difference in the OID served back at all. Are there any other prerequisites I'm missing? I've also noticed that from the time I installed hp-snmp-agents it adds a lot of additional daemons and that my load suddenly jumps to 1. I've uninstalled the package for now. Is this expected behavior?

  Read the article

• Ubuntu 9.10 and Squid 2.7 Transparent Proxy TCP_DENIED

  - by user38400

  Hi, We've spent the last two days trying to get squid 2.7 to work with ubuntu 9.10. The computer running ubuntu has two network interfaces: eth0 and eth1 with dhcp running on eth1. Both interfaces have static ip's, eth0 is connected to the Internet and eth1 is connected to our LAN. We have followed literally dozens of different tutorials with no success. The tutorial here was the last one we did that actually got us some sort of results: http://www.basicconfig.com/linuxnetwork/setup_ubuntu_squid_proxy_server_beginner_guide. When we try to access a site like seriouswheels.com from the LAN we get the following message on the client machine: ERROR The requested URL could not be retrieved Invalid Request error was encountered while trying to process the request: GET / HTTP/1.1 Host: www.seriouswheels.com Connection: keep-alive User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US) AppleWebKit/532.9 (KHTML, like Gecko) Chrome/5.0.307.11 Safari/532.9 Cache-Control: max-age=0 Accept: application/xml,application/xhtml+xml,text/html;q=0.9,text/plain;q=0.8,image/png,/;q=0.5 Accept-Encoding: gzip,deflate,sdch Cookie: __utmz=88947353.1269218405.1.1.utmccn=(direct)|utmcsr=(direct)|utmcmd=(none); __qca=P0-1052556952-1269218405250; __utma=88947353.1027590811.1269218405.1269218405.1269218405.1; __qseg=Q_D Accept-Language: en-US,en;q=0.8 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Some possible problems are: Missing or unknown request method. Missing URL. Missing HTTP Identifier (HTTP/1.0). Request is too large. Content-Length missing for POST or PUT requests. Illegal character in hostname; underscores are not allowed. Your cache administrator is webmaster. Below are all the configuration files: /etc/squid/squid.conf, /etc/network/if-up.d/00-firewall, /etc/network/interfaces, /var/log/squid/access.log. Something somewhere is wrong but we cannot figure out where. Our end goal for all of this is the superimpose content onto every page that a client requests on the LAN. We've been told that squid is the way to do this but at this point in the game we are just trying to get squid setup correctly as our proxy. Thanks in advance. squid.conf acl all src all acl manager proto cache_object acl localhost src 127.0.0.1/32 acl to_localhost dst 127.0.0.0/8 acl localnet src 192.168.0.0/24 acl SSL_ports port 443 # https acl SSL_ports port 563 # snews acl SSL_ports port 873 # rsync acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl Safe_ports port 631 # cups acl Safe_ports port 873 # rsync acl Safe_ports port 901 # SWAT acl purge method PURGE acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access allow purge localhost http_access deny purge http_access deny !Safe_ports http_access deny CONNECT !SSL_ports http_access allow localhost http_access allow localnet http_access deny all icp_access allow localnet icp_access deny all http_port 3128 hierarchy_stoplist cgi-bin ? cache_dir ufs /var/spool/squid/cache1 1000 16 256 access_log /var/log/squid/access.log squid refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern (Release|Package(.gz)*)$ 0 20% 2880 refresh_pattern . 0 20% 4320 acl shoutcast rep_header X-HTTP09-First-Line ^ICY.[0-9] upgrade_http0.9 deny shoutcast acl apache rep_header Server ^Apache broken_vary_encoding allow apache extension_methods REPORT MERGE MKACTIVITY CHECKOUT cache_mgr webmaster cache_effective_user proxy cache_effective_group proxy hosts_file /etc/hosts coredump_dir /var/spool/squid access.log 1269243042.740 0 192.168.1.11 TCP_DENIED/400 2576 GET NONE:// - NONE/- text/html 00-firewall iptables -F iptables -t nat -F iptables -t mangle -F iptables -X echo 1 | tee /proc/sys/net/ipv4/ip_forward iptables -t nat -A POSTROUTING -j MASQUERADE iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-port 3128 networking auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 142.104.109.179 netmask 255.255.224.0 gateway 142.104.127.254 auto eth1 iface eth1 inet static address 192.168.1.100 netmask 255.255.255.0

  Read the article

• Internal drives vs USB-3 with external SSD or eSata with External SSD

  - by normstorm

  I have a need to carry VMWare Virtual Machines with me for work. These are very large files (each VM is 20GB or more) and I carry around about 40 to 50 VM's to simulate different software configurations for different client needs. Key: they won't fit on the internal hard drive of my current laptop. I currently execute the VM's from an external 7200RPM 2.5" USB-2 drive. I keep copies of the VM's on other 5400 external USB-2 drives. The VM's work from this drive, but they are slow, costing me much time and frustration. It can take upwards of 30 minutes just to make a copy of one of the VM's. They can take upwards of 10-15 minutes to fully launch and then they operate sluggishly. I am buying a new laptop (Core I7, 8GB RAM and other high-end specs). I intend to buy an SSD for the O/S volume (C:). This SSD will not be large enough to hold the VM's. I have always wanted a second internal hard drive to operate the VM's. To have two hard drives, though, I am finding that I will have to go to a 17" laptop which would be bulky/heavy. I am instead considering purchasing a 15" laptop with either an eSATA port or USB-3 ports and then purchasing two external drives. One of the drives might be an external SSD (maybe OCX brand) for operating the VM's and the other a 7400RPM 1TB hard drive for carrying around the VM's not currently in use. The question is which options would give me the biggest bang for the buck and the weight: 1) 2nd Internal SSD hard drive. This would mean buying a 17" laptop with two drive "bays". The first bay would hold an SSD drive for the C: drive. I would leave the first bay empty from the manufacture and then purchase/install an aftermarket SSD drive. This second SSD drive would have to be very large (256 GB), which would be expensive. I would still also need another external hard drive for carrying around the VM's not in use. 2) 2nd internal hard drive - 7400 RPM. Again, a 17" laptop would be required, but there are models available with on SSD drive for the C: drive and a second 7200 RPM hard drives. The second drive could probably be large enough to hold the VM's in use as well as those not in use. But would it be fast enough to drive the VM's? 3) USB-3 with External SSD. I could buy a 15" laptop with an SSD drive for the C: drive and a second hard drive for general files. I would operate the VM's from an external USB-3 SSD drive and have a third USB-3 external 7200 RPM drive for holding the VM's not in use. 4) eSATA with External SSD. Ditto, just eSATA instead of USB-3 5) USB-3 with External 7400 RPM drive. Ditto, but the drive running the VM's would be USB-3 attached 7400 RPM drives rather than SSD. 6) eSATA with External 7400 RPM drive. Dittor, but the drive running the VM's would be eSATA attached 7400 RPM drives rather than SSD. Any thoughts on this and any creative solutions?

  Read the article

• Setting up apache to view https pages

  - by zac

  I am trying to set up a site using vmware workstation, ubuntu 11.10, and apache2. The site works fine but now the https pages are not showing up. For example if I try to go to https://www.mysite.com/checkout I just see the message Not Found The requested URL /checkout/ was not found on this server. I dont really know what I am doing and have tried a lot of things to get the ssl certificates in there right. A few things I have in there, in my httpd.conf I just have : ServerName localhost In my ports.conf I have : NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 http </IfModule> <IfModule mod_gnutls.c> Listen 443 http </IfModule> In the /etc/apache2/sites-available/default-ssl : <IfModule mod_ssl.c> <VirtualHost _default_:443> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> .... truncated in the sites-available/default I have : <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www #DocumentRoot /home/magento/site/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> #<Directory /home/magento/site/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> <virtualhost *:443> SSLEngine on SSLCertificateFile /etc/apache2/ssl/server.crt SSLCertificateKeyFile /etc/apache2/ssl/server.key ServerAdmin webmaster@localhost <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> #<Directory /home/magento/site/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> </virtualhost> I also have in sites-availabe a file setup for my site url, www.mysite.com so in /etc/apache2/sites-available/mysite.com <VirtualHost *:80> ServerName mysite.com DocumentRoot /home/magento/mysite.com <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /home/magento/mysite.com/ > Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog /home/magento/logs/apache.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn </VirtualHost> <VirtualHost *:443> ServerName mysite.com DocumentRoot /home/magento/mysite.com <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /home/magento/mysite.com/ > Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ErrorLog /home/magento/logs/apache.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn </VirtualHost> Thanks for any help getting this setup! As is probably obvious from this post I am pretty lost at this point.

  Read the article

• How do I determine if my controller is in IDE or AHCI mode in Linux?

  - by philcolbourn

  I have an old MacBook Pro 4,1 (early 2008) - but I suspect an answer would apply to many MacBook Pros. It has an Intel IDE/SATA controller (ICH8M/ICH8M-E). I have installed a patched MBR that is supposed to put my controller into AHCI mode. It does this by setting some controller port value that I don't understand. This seems to work as I get this from lspci: 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) Now most, perhaps all, sites that provide a solution (enabling AHCI) suggest that after a sleep/wake cycle that a controller will revert to IDE mode due to how Apple support Windows. They recommend disabling sleep. From author of patchedcode.bin I think Enabling AHCI for Windows on MacBooks NB: I do not have bootcamp installed and I do not have Windows installed. Is there a way to prove that my controller is in IDE or AHCI mode? Background Data Using patchedcode.bin MBR I get this in syslog: Jun 12 22:33:22 max kernel: [ 1.860955] ahci 0000:00:1f.2: version 3.0 Jun 12 22:33:22 max kernel: [ 1.861052] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X Jun 12 22:33:22 max kernel: [ 1.861117] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x1 impl SATA mode Jun 12 22:33:22 max kernel: [ 1.861120] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems Jun 12 22:33:22 max kernel: [ 1.861130] ahci 0000:00:1f.2: setting latency timer to 64 Jun 12 22:33:22 max kernel: [ 1.880880] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) Jun 12 22:33:22 max kernel: [ 1.880983] scsi2 : ahci Jun 12 22:33:22 max kernel: [ 1.884552] scsi3 : ahci Jun 12 22:33:22 max kernel: [ 1.886932] scsi4 : ahci Jun 12 22:33:22 max kernel: [ 1.886998] ata3: SATA max UDMA/133 abar m2048@0xdb504000 port 0xdb504100 irq 45 Jun 12 22:33:22 max kernel: [ 1.887000] ata4: DUMMY Jun 12 22:33:22 max kernel: [ 1.887002] ata5: DUMMY Jun 12 22:33:22 max kernel: [ 2.204103] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 12 22:33:22 max kernel: [ 2.204656] ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100 Jun 12 22:33:22 max kernel: [ 2.204662] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32), AA Jun 12 22:33:22 max kernel: [ 2.205324] ata3.00: configured for UDMA/100 Jun 12 22:33:22 max kernel: [ 2.205554] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHY2200B 0081 PQ: 0 ANSI: 5 Using my original MBR I get this from syslog: Jun 13 18:07:13 max kernel: [ 0.622861] ata_piix 0000:00:1f.1: version 2.13 Jun 13 18:07:13 max kernel: [ 0.622869] ata_piix 0000:00:1f.1: power state changed by ACPI to D0 Jun 13 18:07:13 max kernel: [ 0.622924] ata_piix 0000:00:1f.1: setting latency timer to 64 Jun 13 18:07:13 max kernel: [ 0.623339] scsi0 : ata_piix Jun 13 18:07:13 max kernel: [ 0.623730] scsi1 : ata_piix Jun 13 18:07:13 max kernel: [ 0.623765] ata1: PATA max UDMA/100 cmd 0x8108 ctl 0x811c bmdma 0x80e0 irq 21 Jun 13 18:07:13 max kernel: [ 0.623767] ata2: PATA max UDMA/100 cmd 0x8100 ctl 0x8118 bmdma 0x80e8 irq 21 Jun 13 18:07:13 max kernel: [ 0.623810] ata_piix 0000:00:1f.2: MAP [ Jun 13 18:07:13 max kernel: [ 0.623811] P0 -- -- -- ] Jun 13 18:07:13 max kernel: [ 0.623866] ata_piix 0000:00:1f.2: setting latency timer to 64 Jun 13 18:07:13 max kernel: [ 0.624241] scsi2 : ata_piix Jun 13 18:07:13 max kernel: [ 0.624558] scsi3 : ata_piix Jun 13 18:07:13 max kernel: [ 0.624862] ata3: SATA max UDMA/133 cmd 0x80f8 ctl 0x8114 bmdma 0x8020 irq 18 Jun 13 18:07:13 max kernel: [ 0.624865] ata4: SATA max UDMA/133 cmd 0x80f0 ctl 0x8110 bmdma 0x8028 irq 18 Jun 13 18:07:13 max kernel: [ 1.208879] ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100 Jun 13 18:07:13 max kernel: [ 1.208882] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 0/32) Jun 13 18:07:13 max kernel: [ 1.208961] ata1.01: ATAPI: MATSHITA DVD+/-RW UJ-867S, 1.00, max UDMA/33 Jun 13 18:07:13 max kernel: [ 1.216186] ata3.00: configured for UDMA/100 Jun 13 18:07:13 max kernel: [ 1.224396] ata1.01: configured for UDMA/33

  Read the article

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• proftpd, dynamic IP, and filezilla: port troubles

  - by Yami

  The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

  Read the article

• Using Juniper EX3300 as a router

  - by Richard Whitman

  So I have a Juniper EX3300 Switch. One of its uplink ports (ge-0/1/0) is connected to my ISP's router. ISP router's port address is xx.xx.xx.109. My switch's IP address is xx.xx.xx.110. From the switch, I can ping to xx.xx.xx.109 and any other IP in the world. I mean its connected to the Internet. I connected the port eth0 of a computer (running Ubuntu) to the port ge-0/0/0 of the switch (which in the same VLAN as ge-0/1/0). I configured the port eth0 as follows: iface eth0 inet static address yy.yy.yy.208 netmask 255.255.255.240 gateway xx.xx.xx.110 yy.yy.yy.208 is assigned to me by the ISP. So, now I can ping to the switch (xx.xx.xx.110) from this computer. But I can not ping to either xx.xx.xx.109 (ISP router) or any other IP. I want this computer to be connected to the Internet. What am I doing wrong? Here are some of the configurations on my switch: interfaces { ge-0/0/0 { unit 0 { family ethernet-switching; } } . . . ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family ethernet-switching { port-mode access; } } } . . . vlan { unit 0 { family inet { address 10.0.1.1/24; } } unit 1 { family inet { address xx.xx.xx.110/30; } } } } . . . routing-options { static { route 0.0.0.0/0 { next-hop xx.xx.xx.109; retain; } } } vlans { Cogent { vlan-id 3; interface { ge-0/1/0.0; ge-0/0/0.0; ge-0/0/1.0; ge-0/0/2.0; ge-0/0/3.0; } l3-interface vlan.1; } TFLan { vlan-id 2; interface { ge-0/0/5.0; ge-0/0/6.0; ge-0/0/7.0; ge-0/0/8.0; ge-0/0/9.0; ge-0/0/10.0; ge-0/0/11.0; ge-0/0/12.0; ge-0/0/13.0; ge-0/0/14.0; ge-0/0/15.0; ge-0/0/16.0; ge-0/0/17.0; ge-0/0/18.0; ge-0/0/19.0; ge-0/0/20.0; ge-0/0/21.0; ge-0/0/22.0; ge-0/0/23.0; ge-0/0/4.0; } l3-interface vlan.0; } }

  Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >