Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 126/600 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

• Cablemodem frequent connection loss

  - by LVDave

  I have a Linksys BEFCMU10 cablemodem and a WRT54GL router with Tomato 1.27 firmware on Cox cable. My question is this: I get what seems to be random disconnects from the internet, where the cable modem lights are still normal, but I can connect nowhere, either via a url or an ip address. At the same time these disconnects are happening, I can go to the router's Tomato management webpage, and release/renew my external IP address from Cox's DHCP server. I've had Cox look at the signal levels on the cable modem, and they say they look fine. What brings back the modem, for sometimes as long as 17 days, is several power-cycles of the modem. I don't understand the underlying cable modem technology too well, but I do know that if I'm able to release/renew the DHCP-provided WAN address, I'd expect that the cable modem was working ok... Anybody have any ideas??

  Read the article

• resolv.conf doesn't get set on reboot when networking is configured for static ip

  - by kenneth koontz

  I'm experiencing, what appears to be a hostname resolution issue in ubuntu 12.04 server edition when configuring my computer to use a static ip. In /etc/network/interfaces: # The primary network interface auto eth0 iface eth0 inet static address 192.168.1.28 netmask 255.255.255.0 gateway 192.168.1.1 Running $ sudo apt-get upgrade, results in a 'Failed to fetch...': . . . W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-backports/universe/i18n/Translation-en_US Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/precise-backports/universe/i18n/Translation-en Something wicked happened resolving 'us.archive.ubuntu.com:http' (-5 - No address associated with hostname) E: Some index files failed to download. They have been ignored, or old ones used instead. When I change my /etc/network/interfaces to: auto eth0 iface eth0 inet dhcp Everything works fine. Looking into /etc/resolv.conf provides some more hints...In cases where I was getting the resolving issue, resolve.conf was empty. No nameservers were specified. When I changed to dhcp from static and restarted networking. /etc/resolv.conf gets written to: 'nameserver 192.168.1.1'. Switching back from dhcp to static and restarting doesn't remove the nameserve entry. When I restart the system with static set, resolv.conf is empty. When I restart the system with dhcp set, resolv.conf has nameserver 192.168.1.1. So it appears that the issue is that resolve.conf is not getting written to correctly? Which package/code is responsible for writing to resolv.conf? Is there a particular package that I can take a look at open issues? UPDATE: istream posted a good article discussing changes to resolve.conf in 12.04. http://www.stgraber.org/2012/02/24/dns-in-ubuntu-12-04/

  Read the article

• Customizing post-commit messages in svn for different users

  - by Suresh

  I have an svn repository that users can access (read/write) using their account OR via tunneling over ssh with svnserve. I also have a post-commit hook that sends mails to specific users for different projects via svnnotify: the typical command is svnnotify <params> --to-regex-map <list of email IDs> <regex> For users who have accounts on the system, the notification email is sent from @machine.domain, which is fine. For users coming in via tunnelling, the email gets sent from @machine.domain, which is a fake address since these users don't have an account - the only reason I specify a tunnel-user id is to keep track of who made which update. So my question (finally) is: is there a way to pass a parameter (the "true" email address) to svnserve so that when the post-commit mail is sent, it can be sent "from" the correct email address ? p.s this is my first post here - if I haven't provided sufficient information, apologies: I'm happy to provide more details.

  Read the article

• Unable to setup ssh tunnel on mac

  - by prashant

  On my office windows XP laptop I use a program called Bitvise Tunnelier to establish ssh tunnel to a in-house MySQL database. In the Tunnelier program I also need to provide address of corporate http proxy server in order to establish tunnel. On my personal mac laptop, I use Cisco Anywhere client to establish a VPN connection to my corporate network. But i'm unable to establish ssh tunnel to mysql database using ssh. How do I specify the proxy server address in the ssh command? As additional info when i'm using office laptop (whether in home or office) I can successfully ping to the server address specified in the Tunnelier program. But i cannot ping the same server using my mac machine (even after connecting via VPN). So basically i'm unable to understand what's going on and what steps i can take to debug this problem .

  Read the article

• Why am I having DNS problems going through Network Solutions DNS to Amazon AWS?

  - by BestPractices

  Network Solutions appears to have an issue with AWS hostnames. This AWS ELB has been out there for months and is resolvable from every major DNS provider but network solutions. Any idea as to why? WORKING (4.2.2.2 DNS) $ nslookup testloadbalancer-1761726467.us-west-2.elb.amazonaws.com Server: 4.2.2.5 Address: 4.2.2.5#53 Non-authoritative answer: Name: testloadbalancer-1761726467.us-west-2.elb.amazonaws.com Address: 50.112.251.201 NOT WORKING (Network Solutions DNS) $ nslookup testloadbalancer-1761726467.us-west-2.elb.amazonaws.com ns1.worldnic.com Server: ns1.worldnic.com Address: 205.178.190.1#53 ** server can't find testloadbalancer-1761726467.us-west-2.elb.amazonaws.com.localhost: SERVFAIL

  Read the article

• Red Hat cluster: Failure of one of two services sharing the same virtual IP tears down IP

  - by js01

  I'm creating a 2+1 failover cluster under Red Hat 5.5 with 4 services of which 2 have to run on the same node, sharing the same virtual IP address. One of the services on each node needs a (SAN) disk, the other doesn't. I'm using HA-LVM. When I shut down (via ifdown) the two interfaces connected to the SAN to simulate SAN failure, the service needing the disk is disabled, the other keeps running, as expected. Surprisingly (and unfortunately), the virtual IP address shared by the two services on the same machine is also removed, rendering the still-running service useless. How can I configure the cluster to keep the IP address up?

  Read the article

• Static IPv4 and dynamic IPv6 on same interface

  - by Zsub

  I am trying to set up a CentOS 5.4 box to use a static IPv4 address, while getting a dynamic IPv6 address at boot time. I have only one interface, apart from the loopback interface, eth0. It has a static v4 and internet connectivity (I can SSH in). However, it doesn't get an IPv6 by default. I have enabled IPv6 in /etc/sysconfig/network and I have added IPV6INIT=yes to the config in /etc/sysconfig/networking/devices/. If I use dhcp6c it does get a valid IPv6 address, but the main question is how do I configure it to get one at boot-time?

  Read the article

• BizTalk: mapping with Xslt

  - by Leonid Ganeline

  BizTalk Map Editor (Mapper) is a good editor, especially in the last 2010 version of the BizTalk. But still sometimes it cannot do the tasks easily. It is time for the Xslt code, It is time to remember that the maps are executed by the Xslt engine.  Right-click the Mapper Grid (a field between the source and target schemas) and choose Properties /Custom XSLT Path.  Input here a name of the file with Xslt code. Only this code will be executed, forget the picture in the Mapper, all those links and functoids.  Let’s see the real-life example. There are two source Addresses. One is on the top level and the second is inside the Member_Address record with MaxOccurs=* . The target address is placed inside the Locator record with MaxOccurs=*. The requirement is to map all source address to the one target address structure. The source Xml document looks like: The result Xml should be like this: Try to do this mapping with the Mapper and you will spent good amount of time and the result map would be tricky. If we use the Xslt code, the mapping will be simple and unambiguous, like this: Simple, elegant.

  Read the article

• How to efficiently merge a lot of vCard files for the same person?

  - by mihi

  I currently have contact information at several places: old PDA's address book mobile phone's phone book (primarily name, phone number) email client's address book (primarily name, email) web mailer's address book (primarily name, email) instant messenger's contact list (primarily name, im, email, birthday) And there are several social or business networking sites on the Internet where contacts provide information about themselves, like LinkedIn or XING. All those sources can export as vCard, but as you might imagine, I get a lot of vCards for the very same contact that way. Are there any tools where I can import them and then merge them (it may ask me which phone number is more current in case of field clashes of course)? Bonus points if it can track which information I have discarded so when I re-export all information from one of the sources I can't import to (networking sites), it won't ask me again if I want to overwrite phone number of person X with the same ancient number... I hope you understand what I try to accomplish, if not just ask :-)

  Read the article

• How to set up different documentroot for ip based requests, and different for domain based requests

  - by Carlos

  My problem is simply that I have a domain, let's say example.com, and my server's ip address is e.g. 192.168.0.1. I want to set up 2 different virtual hosts, so when user enters ip address (192.168.0.1) in his browser, he will see content from here: /var/www/staging But if user will type example.com, he will see content from here: /var/www I think it's possible but I was playing around with it and couldn't make it work. Also I don't want to make simple redirection. I know I can, but I need both of my apps (live & staging) working in root on the same server. I can't buy second domain, and I can't associate new ip address.

  Read the article

• How to set up server/domain name correctly in hosts file with HTTPS

  - by Byakugan

  I am trying to do local network and I am using these kind of types of network. 1) Main server which connects to internet with static IP 2) Second computer connected to first one locally with address like 192.168.0.2 - when I write this address to address line it is like i wrote localhost in original main server - so it should show my local web browser etc ... It has domain name this IP and connected router for it ... example www.domain.com so I added to my main server hosts file (linux powered) lines like these: 192.168.0.2 domain.com www.domain.com It was working ok when I entered my domain name in local computer it showed my site ... But after some time I added HTTPS cerfiticate and added this line to my apatche server: Redirect permanent / https://www.domain.com/ And now it does not work even when i add something like this to my hosts file: 192.168.0.2 https://www.domain.com So any idea how do do this thing work? Thank you.

  Read the article

• webmin bind issue- error when i try to start bind

  - by Arvind

  I am setting up a domain = mydomain.com with 2 nameservers ns1.mydomain.com and ns2.mydomain.com in Webmin - BIND. For this, I have registered 2 child nameservers at my domain registrar, and in Webmin-Bind I have set up a new zone for this domain. In this zone, i have specified 2 nameserver records- one each for ns1 and ns2. Also, I have defined 2 address records- one each for ns1.mydomain.com -> IP Address #1 and for ns2.mydomain.com -> IP Address #2 However when I try to start BIND in Webmin, I get the following error-- Failed to start BIND : Starting named: Error in named configuration: zone mydomain.com/IN: has no NS records zone mydomain.com/IN: not loaded due to errors. _default/mydomain.com/IN: bad zone [FAILED]

  Read the article

• Problems Using CloudFlare On Blogger

  - by the_archer

  Here's the situation. I got a TLD for my blogger blog and set it up using the instructions from blogger. Blogger asks to: Add two CNAME records. For the first CNAME, where it says Name, Label or Host enter "www" and where it says Destination, Target orPoints To enter "ghs.google.com" . For the second CNAME, enter "NHRILA4K2RJG" as the Name and "gv-GQMUMYGHAMJWECXFLJXVXABIV23C55JIPNIAVD5IGFSXT653O5GA.domainverify.googlehosted.com." I did that on my domain host, and everything was working smoothly. Here's the things that happened: Typing myblog.blogspot.com in the address bar brought me to my new address www.mynewaddress.tld Typing my newaddress.tld brings me to www.mynewaddress.tld Now, I went through the instruction to setup CloudFlare and did everything as required. I saw that CloudFlare is active and working on my TLD www.mynewaddress.tld, however, when I am typing the blogspot address, i.e. myblog.blogspot.com, it's showing a notice that the blog is not hosted on blogger and that I should click "yes" to get redirected to the new website. However, the blog is still on blogger. I think the problem might be with this particular CNAME record Google asks to create, which I did not find imported to the CloudFlare nameservers: For the second CNAME, enter "NHRILA4K2RJG" as the Name and "gv-GQMUMYGHAMJWECXFLJXVXABIV23C55JIPNIAVD5IGFSXT653O5GA.domainverify.googlehosted.com." So I create that CNAME and added it to the CloudFlare panel. My question is - is that what will help Google determine that my blog is still hosted on Blogger? If so, should I turn off CloudFlare for that particular CNAME record or turn it on? Any help is very much appreciated :)

  Read the article

• IPs on home network

  - by windchime

  I have a Linksys router and a Belkin wireless router at home. The Linksys router is connected to cable modem and two computers, as well as to the Belkin wireless router. A 3rd computer is connected to the Belkin router through Wifi. The IP addresses of the computers connected to Linksys are 192.168.1.101 and 192.168.1.102. The IP address of the Linksys router on LAN is 192.168.1.1. The IP address of the Belkin wireless router is 192.168.2.1(based on the 3rd computer's routing table) and the IP address of the 3rd computer is 192.168.2.5. If I ping 192.168.1.101 from 192.168.2.5, all are well. However, if I ping 192.168.2.5 from 192.168.1.101, Destination Host Unreachable. Why?

  Read the article

• Apache port forwarding with ZTE ZXV10 W300 router (provider specific firmware)

  - by dannote

  I'm trying to configure port forwarding for Apache 2.2 installed on Windows XP SP3 with ZTE ZXV10 W300 router. The computer has a static IP 192.168.1.2. Port forwarding is configured as following: Enable true Name Apache Protocol TCP (also tried TCP and UPD) WAN Host Start IP Address empty WAN Host End IP Address empty WAN Connection stream WAN Start Port 8080 WAN End Port 8080 LAN Host IP Address 192.168.1.2 LAN Host Start Port 8080 LAN Host End Port 8080 Port 8080 is open for both TCP and UPD in Windows Brandmauer. Apache configuration: Listen 192.168.1.2:8080 Router Firmware: Hardware Version V1.0.01 Software Version V8.0.02T03_CFA Boot Loader Version V1.1.2 The provider is COMSTAR. I'm not sure but it's said they flash routers with modified firmware. I have also tried to set up Bitcomet port forwarding on port 13514 and failed.

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Google Mail: Import labels when switching from POP3 to IMAP

  - by toobb

  My situation is the following: I have a Google Mail email-address and I have been using this address in Thunderbird fetching the emails with POP3 (the emails also remained on the server and where "archived"). In Thunderbird I organized my emails in folders. Now I want to switch to IMAP (with the same email address), but I want to keep the folder structure I created in Thunderbird. I could create a 2nd account in Thunderbird that uses IMAP, and then move my folders from the old account to the new one. But the problem is, that Google Mail probably does not recognize that it already has these moved emails in "All Mails". I will probably end up with two copies of every email. Does someone has good idea how to deal with that problem? Thank you!

  Read the article

• Running scheduled web scripts in a Windows Server environment

  - by Dan Murfitt

  I'm trying to get a scheduled web script running on a Windows Server and so far the only way I've managed to automate this process is by using the Task Scheduler to open Internet Explorer with the web address as a parameter. I then need to create a separate task to run just after this task to close Internet Explorer (otherwise the task doesn't complete). Is there a better way of doing this? I've also managed to run the script by calling the web address through a Telnet connection to the web server (GET /web/address/here) but I haven't found a way of automating this process on a scheduled basis. Any ideas appreciated

  Read the article

• How do I handle mysql replication in EC2 using private IPs?

  - by chris

  I am trying to set up a mysql master/slave configuration in two EC2 instances. However, every time I reboot an instance, the IP address (and hostname) changes. I could assign an Elastic IP address, but would prefer to use the internal IP address. I can't be the first person to do this, but I can't seem to find a solution. There are a lot of "getting started" guides, but none of them mention how to handle changing IP addresses. So what are the best practices to manage master/slave replication in EC2?

  Read the article

• Microsoft ISA 2004 - Failed Connection Attempt

  - by Arief

  I have an issue where users with Android tablet cannot download apps through ISA 2004. This is what I get from the ISA 2004 logging: I did try to add the source ip address and the destination ip address in All for All Modified rule. However, it does not fix that problem. I also use GFI Web Monitoring. I did add the 151.101.13.80 ip address into the Whitelist, and no luck. What Failed Connection Attempt exactly is? How to overcome this. The Android tablet is throwing an error 495, could not be downloaded. Thanks everyone.

  Read the article

• SQL Azure Security: DoS

  - by Herve Roggero

  Since I decided to understand in more depth how SQL Azure works I started to dig into its performance characteristics. So I decided to write an application that allows me to put SQL Azure to the test and compare results with a local SQL Server database. One of the options I added is the ability to issue the same command on multiple threads to get certain performance metrics. That's when I stumbled on an interesting security feature of SQL Azure: its Denial of Service (DoS) detection engine. What this security feature does is that it performs a check on the number of connections being established, and if the rate of connection is too high, SQL Azure blocks all communication from that machine. I am still trying to learn more about this specific feature, but it appears that going to the SQL Azure portal and testing the connection from the portal "resets" the feature and you are allowed to connect again... until you reach the login threashold. In the specific test I was performing, all the logins were successful. I haven't tried to login with an invalid account or password... that will be for next time. On my Linked In group (SQL Server and SQL Azure Security: http://www.linkedin.com/groups?gid=2569994&trk=hb_side_g) Chip Andrews (www.sqlsecurity.com) pointed out that this feature in itself could present an internal threat. In theory, a rogue application could be issuing many login requests from a NATed network, which could potentially prevent any production system from connecting to SQL Azure within the same network. My initial response was that this could indeed be the case. However, while the TCP protocol contains the latest NATed IP address of a machine (which masks the origin of the machine making the SQL request), the TDS protocol itself contains the IP Address of the machine making the initial request; so technically there would be a way for SQL Azure to block only the internal IP address making the rogue requests.  So this warrants further investigation... stay tuned...

  Read the article

• Call issue with Freeswitch

  - by gbraad

  I am testing the following with Freeswitch and different devices (nokia n900, nokia e60, ekiga) and have similar results between them. On the Freeswitch server (1.0.4 in multi-tenant mode) I have several user profiles for a domain, e.g. 1000, 1001 for host.com The user are authenticated correctly and calls can be placede. When I place a call from a device registered as [email protected] to [email protected] it will show up at the other end (1002) as [email protected] I would expect this call to show up as [email protected]. The IP address is the one of from the Freeswitch server. Because of this, the calls are no correctly recognized by the address book on certain devices. Can the he domain FQDN of the callers domain/acount be used, instead of the IP address of the server in the SIP uri?

  Read the article

• Using JuJu with private Openstack cloud deployment?

  - by user76054

  I'm seeing a number of problems trying to use JuJu with our internally deployed Openstack cloud. Most of this appears to be centered around DNS host resolution as well as the need to deal with our company's internal HTTP proxies. Our Openstack deployment relies upon an unroutable 172.16.0.0/12 block of addresses for VLAN allocation to each project (tenant) hosted on our internal cloud. User's have the option of assigning one or more floating addresses to instances, allocated from a block of routable addresses on our internal companies LAN. Currently, Openstack doesn't register instance names with anything other than the DNSMASQ service running on the cloud controller. As such, there's no way to resolve this address through our internal DNS hierarchy (this issue has already been reported as Bug #945505). As such, even though I can bootstrap my JuJu server node, I can't connect to it with the JuJu client, since it can't resolve the local (private) network name. I am able to ssh to the node, once I've assigned it an internally routable (i.e. floating) address. Which leads to the next issue. Next, to install software on an instance running in our cloud, it must have our internal proxy address defined - either in the apt.conf file or via environment variables. Unfortunately, when bootstrapping the server node, there's no provision to pass this info into a instance via JuJu environment.yaml file (if this is even the best way to handle this issue). As a result, the bootstrap node is unable to install the required packages. I'm assuming (dangerous, I know) that the way that I've deployed Openstack in our internal environment is probably not unique. Has anyone else encountered these issues? And more importantly, are work arounds available? Regards, Ross

  Read the article

• USB resets with Ubuntu 9.10

  - by Grumbel

  Since the upgrade to Ubuntu 9.10 I have issues with getting USB device resets on my Maxtor OneTouch USB harddrive: Nov 9 20:54:37 localhost kernel: [32459.100021] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 21:54:37 localhost kernel: [36059.100017] usb 2-2: reset high speed USB device using ehci_hcd and address 4 Nov 9 23:24:37 localhost kernel: [41459.112025] usb 2-2: reset high speed USB device using ehci_hcd and address 4 The device itself continues to work fine, the resets however wake the device out of its sleep state and thus cause it to spin up, which is very annoying. Interestingly, as the log shows, the resets happen at pretty regular intervals (i.e. one hour or half an hour), not randomly. An USB card reader seems to have the same issues, while another USB harddrive from a different manufactor works fine on the same PC. What could be causing this and how could I fix it?

  Read the article

• Getting my IP off the hotmail blacklist

  - by Kai

  I got a new server with a new IP address. Apparently this IP is listed in the hotmail blacklists so that I can't send mails to hotmail users out of my webapplication. postfix/smtp[24706]: 8F31C9404B: to=<[email protected]>, relay=mx3.hotmail.com[65.55.37.88]:25, delay=0.66, delays=0.01/0/0.48/0.16, dsn=5.0.0, status=bounced (host mx3.hotmail.com[65.55.37.88] said: 550 SC-001 Unfortunately, messages from 78.47.228.xxx weren't sent. Please contact your Internet service provider since part of their network is on our block list. You can also refer your provider to http://mail.live.com/mail/troubleshooting.aspx#errors. (in reply to MAIL FROM command)) My hoster will not help me get that address removed from the blacklist. So I tried to find a way to do it on my own, but I can't find a way to ask Microsoft to remove my IP from that list. Has anyone managed to remove a falsely listed address? And if yes: how?

  Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >