Search Results

Search found 29864 results on 1195 pages for 'ubuntu 9 04'.

Page 126/1195 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

• Ubuntu 10.4 Lucid Server Minimal Install: Slow terminal scrolling

  - by noname

  I have a minimal install of Ubuntu 10.4 Server for testing and learning purposes. There is a very annoying occurrance: whenever I try to "man dpkg" or any command that load a few screens length of text (eg. "ls -al") the redraw speed of the console is just way too slow. I can see how each new line causes the whole screen to redraw. Note: that this doesn't happen inside X. No gui is installed. I have been experimenting with adding vesafb to the grub line as some guides suggested, but no speedups happened. You might be able to reproduce this behaviour on your linux system by switching to terminal using CTRL+ALT+F1. Is there any way to speed scrolling up?

  Read the article

• HDMI output issue in Ubuntu

  - by xsznix

  Hi, I am using Ubuntu 10.04 on a HP notebook with a nVidia GT 130M graphics card. Whenever I connect a HDTV using the HDMI output and set all of the settings in the nVidia Control Panel, it will output to the HDTV, but cut off about 24 pixels on each side. Sometimes (but not often), it will work properly (display the entire screen), but I cannot get it to work thus consistently. I have tried using resolutions of 1920x1080, 1360x768, 800x600 with two HDTVs of different brands, with and without forcing full GPU scaling, with and without syncing to VBlank (what is this?), etc., and also using a Linux Mint 9 computer with integrated Intel (X4000-ish, don't remember exactly) graphics. The problem persists no matter what, but only with HDMI output (VGA works fine). The same computers works fine with HDTVs in Windows. Any ideas?

  Read the article

• ubuntu 9.04 /var/www permissions

  - by luca

  ubuntu 9.04, user luca wants to access the /var/www directory. the directory is owned by user root, group root I changed the group ownership to www-data (sudo chgrp -R www-data /var/www/) and added write privileges to that group (sudo chmod -R g+r /var/www), and added luca to that group (sudo adduser luca www-data). Now, why can't luca still write to /var/www? It should be able to, right? in /etc/group we have: "www-data:x:33:luca" permissions for /var/www are: "drwxrwxr-x 2 root www-data 4096 Feb 26 15:35 www"

  Read the article

• Ubuntu server 9.10 freezes up after ~10 minutes

  - by Matt Williamson

  I just upgraded my Ubuntu server from 9.04 to 9.10 and after about 10 minutes it locks up. It won't respond to ping, can't ssh in and the terminal doesn't accept keyboard input. It does not have X installed. I then reformatted and installed it from scratch with the same results. There are two hard drives, the first is for the OS and the second is for media. The second has not changed, it is an ext3 formatted drive with one partition. I stopped random services (samba, ushare, transmission-daemon) to see if they were causing the issue, but it still locked up. I did a watch "dmesg|tail" until it locked up, but I didn't see anything. How can I troubleshoot this further? I don't want to downgrade. Machine specs: Dell Dimension 3000 Pentium 4 @3GHz 512M RAM

  Read the article

• Not working WEP key in Ubuntu

  - by stupid-idiot

  This time I've got some problem with connection to the internet from my old laptop with ubuntu, I already had some problems with setting up the radio on my network card but I think it works now since it finds some wireless networks. The problem is that I can't connect to my router via wi-fi even if I'm hundred-percently sure the wepkey I punch there is correct, it works via LAN though. Also, I'm not able to ping myself with 127.0.0.1. I'm sorry to say it but I don't think I can stand this shitness for much longer. Although it's much much faster than Windows it's useless since i can't download any libraries for development. If anyone has any experience with this, even indirect, please leave your answer or comment thx

  Read the article

• Disable MOUSE wakeup when doing suspend on UBUNTU

  - by Shadyabhi

  When I do SUSPEND on ubuntu, in order to wake up, i can just move the mouse and the computer will wake up. But, I dont want that the computer is waked up when I move my mouse. How can I do that? My /proc/acpi/wakeup file:- shadyabhi@shadyabhi-desktop:~$ cat /proc/acpi/wakeup Device S-state Status Sysfs node SLPB S4 *enabled P32 S4 disabled pci:0000:00:1e.0 UAR1 S4 disabled pnp:00:09 ILAN S4 disabled pci:0000:00:19.0 PEGP S4 disabled PEX0 S4 disabled pci:0000:00:1c.0 PEX1 S4 disabled pci:0000:00:1c.1 PEX2 S4 disabled pci:0000:00:1c.2 PEX3 S4 disabled pci:0000:00:1c.3 PEX4 S4 disabled pci:0000:00:1c.4 PEX5 S4 disabled UHC1 S3 disabled pci:0000:00:1d.0 UHC2 S3 disabled pci:0000:00:1d.1 UHC3 S3 disabled pci:0000:00:1d.2 UHC4 S3 disabled EHCI S3 disabled pci:0000:00:1d.7 EHC2 S3 disabled pci:0000:00:1a.7 UH42 S3 disabled pci:0000:00:1a.0 UHC5 S3 disabled pci:0000:00:1a.1 UHC6 S3 disabled pci:0000:00:1a.2 AZAL S3 disabled pci:0000:00:1b.0 shadyabhi@shadyabhi-desktop:~$

  Read the article

• Ubuntu + latest samba version, symlinks no longer work on share mounted in windows

  - by Roy Rico

  I just apt-getted (apt-got?) the latest software for my Ubuntu 9.10 linux box, and I noticed that samba was the included in the update. After the install, the symlinks in my home directory no longer work when mounted as a drive in my linux box. They worked literally seconds before I did the update. All my normal directories work just fine. Viewing the directory listing on the command line, all the files, dirs & links have the exact same permissions, yet this is the error I get: Location is not available L:\LinkDir is not accessible. Access is denied. I looked on the forums, and i saw this option for the smb.conf follow symlinks = yes wide symlinks = yes unix extensions = no I put those in, but they had no effect. Has anyone had this problem yet?

  Read the article

• rc.local is not executed on bootup ubuntu

  - by Alexander

  Im on Ubuntu 10.04. I want to execute script on system boot. I added it to rc.local. If I execute rc.local manually it works fine. If I boot system in recovery mode(2nd string in boot menu) it also works fine. But if I boot normally it is not executed. However i added sleep 20 to my script and there is a pause at the end of boot process, but nothing more is executed. Thanks I think, it soesnt depend on contents of the script but anyway #!/bin/sh -e sleep 20 sudo service ssh start su -c 'service pgsql start' postgres sudo svnserve -d su -c 'hamachi start' root su -c 'hamachi login' root exit 0

  Read the article

• Setting up autotest with rspec in ubuntu

  - by Reactor5

  I'm trying to set up autotest on Ubuntu, and no matter what my configuration, I get this: loading autotest/rails_rspec2 style: RailsRspec2 /home/brian/.rvm/gems/ruby-1.9.2-rc2@rails3tutorial/gems/redgreen-1.2.2/lib/redgreen/autotest.rb:6:in `<top (required)>': uninitialized constant Object::PLATFORM (NameError) the .autotest (~/.autotest) file I have is as follows: #!/usr/bin/env ruby require 'redgreen/autotest' def self.notify title, msg, img, pri='low', time=3000 `notify-send -i #{img} -u #{pri} -t #{time} '#{msg}'` end Autotest.add_hook :ran_command do |at| results = [at.results].flatten.join("\n") output = results.slice(/(\d+)\s+examples?,\s*(\d+)\s+failures?(,\s*(\d+)\s+not implemented)?(,\s*(\d+)\s+pending)?/) folder = "~/Pictures/autotest/" if output =~ /([123456789]|[\d]{2,})\sfailures?/ notify "FAIL:", "#{output}", folder+"rails_fail.png", 'critical', 10000 elsif output =~ /[1-9]\d*\spending?/ notify "PENDING:", "#{output}", folder+"rails_pending.png", 'normal', 10000 else notify "PASS:", "#{output}", folder+"rails_ok.png" end end what am I doing wrong here?

  Read the article

• "Sticky button" configuration under X11/Ubuntu?

  - by John Whitley

  Is there a configuration or app that will enable Sticky-keys like functionality for a pointer button under X11? (On Ubuntu 9.10, FWIW.) To be clear, I'd like a single tap (down/up events) to be treated as a down event, and a following tap to be treated as an up event. Context: I have a trackball with a fourth button that I've mapped to act as horizontal/vertical scroll. This works great. It'd be even better if I didn't have to hold the button down when scrolling.

  Read the article

• Ubuntu Kernel Panic on Inserting Network Cable

  - by Skizz

  I've been having a recurring kernel panic with my Ubuntu 9.04 installation (see other posts by me). Today, I was fiddling around trying to get some cable attached when the system panicked. Looking at the layout, the only cable in the vicinity was the network cable. Upon further investigation, it seems that the system reliably panics whenever I insert a network cable. Removing the cable does not cause the panic. How do I stop the system panicking when I insert the network cable? If more information is needed, please add comments/answers and I'll post the required data.

  Read the article

• ubuntu server 10 - slow and can't remove desktop environment

  - by Alex

  i'm running ubuntu server 10.10 with the desktop environment. simple page requests are taking over 5 seconds even when connecting to the server through our local network. i believe this is partially related to having the desktop environment installed, as the server worked faster (but not as fast as it should considering that it's on the local network), but tasksel fails every time (aptitude failed 100). my knowledge of networking and linux in general is limited. would really appreciate ideas on how i can troubleshoot this problem. oh also, in the system monitor, one of the processors is almost always around 100%. i doubt this is normal too....

  Read the article

• Ubuntu 9.1 Only Sees 244 MB RAM, while BIOS and Windows Sees 1.5 GB

  - by nicorellius

  I have 1.5 GB of RAM installed on an older Dell, Pentium 4. I just installed Ubuntu 9.1 and the system is only seeing 244 MB of RAM, even though there is 1.5 GB on the system. The BIOS sees all of it. I ran a Knoppix disc and it only saw 25 MB upon booting. I made no particular changes to the installation taht would affect this. I looked through the BIOS and the only setting I could see was the AGP aperture. Not even sure what this is. Anyone know where I went wrong? I also tried moving the memory modules around on the board. Booted with the 1 GB stick, still saw 244 MB.

  Read the article

• Installing a Wl-138g wireless NIC on ubuntu server

  - by Narcolapser

  So I have this little server that I've been working on as a hobby. But due to changes in living arrangements I have move and it won't have access to a wired lan. So I need to install a wireless adapter i had sitting around. But most tutorials I have run across are either out dated, or about ubuntu desktop and talk about things using a GUI. So my question is firstly is there a utility for identifying and downloading drivers for new hardware. that would save my having this problem in the future. If not, how do i go about installing said wireless NIC? ~N

  Read the article

• Compiling Ubuntu server: "libQtGui.so: undefined reference to png functions" errors

  - by Kowalikus

  I want to compile wkhtmltopdf on Ubuntu Server, but I have a problem with following errors: /usr/lib/libQtGui.so: undefined reference to `png_read_info@PNG12_0' /usr/lib/libQtGui.so: undefined reference to `png_set_gAMA@PNG12_0' /usr/lib/libQtGui.so: undefined reference to `png_set_PLTE@PNG12_0' ... /usr/lib/libQtGui.so: undefined reference to `png_create_info_struct@PNG12_0' /usr/lib/libQtGui.so: undefined reference to `png_set_bgr@PNG12_0' /usr/lib/libQtGui.so: undefined reference to `png_get_valid@PNG12_0' What can I do? in /usr/lib lrwxrwxrwx 1 17 2010-02-17 15:00 libQtGui.so -> libQtGui.so.4.5.2 lrwxrwxrwx 1 17 2010-02-17 14:59 libQtGui.so.4 -> libQtGui.so.4.5.2 lrwxrwxrwx 1 17 2010-02-17 14:59 libQtGui.so.4.5 -> libQtGui.so.4.5.2 -rw-r--r-- 1 10071604 2009-10-14 23:34 libQtGui.so.4.5.2

  Read the article

• Ubuntu, control the init startup

  - by Xolve

  Ubuntu uses upstart instead of sysvinit. However there are still runlevels and the links in them. I have installed tor and it has added itself to the startup of the OS. Now I want to remove it and the popular options are to remove the links of starting and stopping the service from runlevels or make the /etc/init.d/ script non-executable. This is fine but this will be problematic in case I want to put tor again on the startup list. How would I know to put the proper sequences in the proper runlevel directories. Is there any complete guide given? What are the rules for this? Any tools to manage the init? Please tell

  Read the article

• /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor disappeared on ubuntu 11.10

  - by Bob

  I have an Ubuntu 11.10 server that has been up for 210 days. I have been frequently doing apt-get upgrade every few weeks, and this time I noticed that my server load average just shot up. The last time this happened between upgrades, it was because the cpu scaling governor was set to ondemand. But this time when I tried to list the contents of /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor the file is missing. There isn't even a cpufreq folder anymore! How do I fix this and ensure there is no cpu scaling going on?

  Read the article

• BitNami LAMP stack on ubuntu

  - by Desmond Liang

  I just installed BitNami LAMP stack on ubuntu. When I visit localhost/127.0.0.1 Apache returns "403 Forbidden. You don't have permission to access / on this server." I try repointing Apache's home directory to another folder (same hard drive, same partition) that's set to 777 recursively. Still getting 403. And then I change the ownership of the directory to under my username and daemon group from root/root. Same error. Am I missing something here?

  Read the article

• Starting Redmine at boot using upstart on Ubuntu

  - by joekr

  So after installing redmine from the repositories on Ubuntu 12.04, i've tried to create an upstart script (see below) so it would start up at boot time. While service redmine start does start redmine, it does not start automatically when booting. Also when i run service redmine stop it does stop redmine but simply hangs until i press ctrl+c Also, after stopping starting it again does not work (Also just hangs). From all the upstart examples and tutorials i have seen this should work, so i guess i'm overlooking something. Any hints ? #Redmine description "Redmine" start on started networking stop on stopping networking stop on starting shutdown console output expect daemon exec ruby /usr/share/redmine/script/server webrick -e production -b 188.40.184.155 -p 3000 -d respawn EDIT: Fixed "typo"

  Read the article

• Recover backup copy of a ubuntu linux installation on a usb stick using dd

  - by user10826

  Hi, I installed Ubuntu 10.04 on a usb stick in persistent install mode. So I could boot the laptop or my desktop computer with the stick, at boot time. Once I needed the 8GB stick for another purposes so I thought about coyping it to my desktop doing from mac os x: dd if=/dev/disks3s of=/Users/jack/Desktop/usb_copy Now I am trying to do the opposite, after having used the stick, which was formatted to NTFS, just doing dd if=/Users/jack/Desktop/usb_copy of=/dev/disks3s but although I can see that almost of the files are there, I can not boot again. IT is also strange the the file permissions are kind of strange, something like _user What can I do ? Thanks

  Read the article

• Watch videos from a remote computer on the LAN on ubuntu

  - by tapan

  I want to watch the videos on a friends computer on the LAN without having to download it. Both of us are running ubuntu. Now one way is to ssh to his computer, cd to the directory where the video is and run the falling command: cat video.avi | ssh me@mycomputer mplayer - This works. However the problem is that I cannot seek inside the video as in can't go forward or backward in it. Is there a method by which I can watch the videos and also seek in them ? I can install any software on his comp and my comp to aid this process. I have root level access on both computers. Any suggestions ?

  Read the article

• Ubuntu Wireless card not found

  - by user32121

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• Ubuntu login takes 15 seconds, "I/O error dev fd0 sector 0"

  - by Dan

  After upgrading to Ubuntu 10.04, when I first login it takes 10+ seconds where it just sits at the gdm backgroup before taking me to gnome. By switching to a terminal window during this 10 seconds I saw the error message "I/O error /dev/fd0 sector 0" being outputted. I assume this has to do with the floppy drive... but I don't even have a floppy drive! How do I disable this device and make this error message go away (and hopefully fix the long wait)? Thanks.

  Read the article

• Ubuntu 9.10: switch in KVM, mouse is detected but not usable immediately

  - by CarlF

  I use a KVM switch to jump between my tower and laptop, both placed on my desk. With Ubuntu 9.04 this worked perfectly. In 9.10, when I switch to the tower, then back to the laptop, the mouse is detected (as shown by /var/log/messages) but moving it has no effect. If I use Ctrl-Alt-F1 to switch to the TTY, then Alt-F7 back to Xorg, the mouse starts working. The tower is running Windows 7, but that shouldn't matter. Sometimes, but not other times, the USB keyboard on the KVM switch is also not usable and I have to use the laptop's built-in keyboard to switch to the TTY. The laptop has two monitors, the built-in and an external. It's (obviously) the external panel that is attached via the KVM switch. Any suggestions? Report to Canonical as a bug?

  Read the article

• Ubuntu 11.04 and OpenLDAP - where is the config?

  - by Tom SKelley

  I've been asked to setup a multimaster LDAP environment on Ubuntu 11.04 - instead of a single master server. I cloned the master server and recreated it into two VMs. I am trying to follow the instructions on the OpenLDAP documentation here: http://www.openldap.org/doc/admin24/replication.html and it talks about modifying the cn=config tree within LDAP. The subdirectory tree appears to be there at: /etc/ldap/slapd.d/ and a slapcat -b cn=config drops out a load of config information. When I try to connect using a browser and the admin bind credentials: ldapsearch -D '<adminDN>' -w <password> -b 'cn=config' I get: # extended LDIF # # LDAPv3 # base <> (default) with scope subtree # filter: (objectclass=*) # requesting: ALL # # search result search: 2 result: 32 No such object I don't see the config context when I connect via an LDAP browser either. I'm sure I'm missing something, but I can't see what it is!

  Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >