Search Results

Search found 11994 results on 480 pages for 'mixed mode'.

Page 127/480 | < Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >

• Installing Ubuntu on Asus G75VW (UEFI)

  - by user101653

  You all are my last hope... help! I bought an Asus G75VW from Best Buy. It has the new UEFI BIOS instead of the old style BIOS (1980's) and has Windows 8 preinstalled. I cannot get the G75VW to install Ubuntu 12.10 in EFI mode. I did get Ubuntu to load if I changed the BIOS to CSM and the computer sees and installs Ubuntu in "legacy mode". I attempted boot repair, and Ubuntu will load after 1 minute but as legacy BIOS only. If I changed the BIOS to UEFI "Binary is whitelisted" is displayed and I get a purple screen. My goal... keep my preinstalled Windows 8 on internal drive bay 1 and install Ubuntu 12.10 on internal drive bay 2... and somehow make a choice on which to choose. I am at a loss. I am a software programmer, but I am very bad at understanding BIOS and partitioning. Any ideas? Has anyone done what I want to do. This is a full second day on my "issue"! If I cannot get Ubuntu installed, I'm returning the laptop. And "wait" until these obstacles of UEFI/EFI and properly handled to allow people to load EFI based Ubuntu without a hitch. Thanks, Dave

  Read the article

• Restart and/or graphics problem in Ubuntu 12.04

  - by kara

  I having been using 12.04 for a couple of months now, with v. little problems. The other day I restarted my computer, and though I think it rebooted, the screen would be black. I could not even get a visual from a live cd. Finally, I was able to get it to load, but the resolution has been completely off. The computer thinks I have a laptop screen, when I actually have a ViewSonic VP2330wb, and it detects only two resolutions. And still, I have a problem with rebooting. If the screen locks after I leave it for a while, I can't get a visual back, and then when I force a shutdown, it takes 3 times for me to get a grub screen. Then I have to boot in recovery mode, and then finally in normal mode, but the screen is still always off. This is my video card: description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list configuration: latency=0 resources: memory:fe000000-fe3fffff memory:d0000000-dfffffff ioport:f000(size=64) I am a new ubuntu user, and am at my wits end. Any help would be greatly appreciated.

  Read the article

• Pasting from vim in terminal to Google Docs (Firefox + Vimperator) - need to understand

  - by LIttle Ancient Forest Kami

  I had some trouble with copy-pasting text from vim in terminal to Google Docs (aka Drive) document (hereafter GDd) in FF browser (with Vimperator). Note: I have a file opened in Vim 7.2 in terminal :version displays both +clipboard and +xterm-clipboard I'm on Ubuntu 10.04 LTS, so I don't think that's Unity-related I want to use Vim, not GVim, nor gedit... I'm avid fan of mouseless navigation, so solution with mouse was not what I wanted. I have the solution, but I need understanding. What I tried and where it gets me: Yanking whole file text via: ggvGy allows me to: paste it via mouse middle button, NOT with Ctrl+v or Shift+Insert here, in text area for entering question text in gedit but NOT in GDd where I want it pasted, even if I switch Vimperator to pass-through mode with Insert does NOT show in XClip after xclip -o From gedit, I can copy-paste the text into GDd (Vimperator's pass-through mode not required). :%! !xclip -i (or :first, last) reports whole file (all lines, to be precise) as filtered, though shell returns 1 `xclip -o' returns nothing (is empty) or returns previously copied value with 2. no surprise, but I can't paste at all not only to GDd but also to gedit or here setting clipboard (:set clipboard=unnamed) to unnamed doesn't help using "+y or "*y on whole file text actually does the trick So, the question (it's actually three, say "split" and I will): why middle mouse button pastes different things than Ctrl+v and how to know what will be pasted with each? why just yanking (without registers) works with mouse but not with keyboard / XClip? why didn't unnamed register help? After setting, it should make unnamed and * registers same?

  Read the article

• Where to install boot loader on a Zenbook Prime?

  - by Christians

  I cannot figure out where to install the boot loader on my Zenbook UX31A Prime. I have installed Ubuntu many times on normal hard drives, but this is the first SSD and I am struggling. Installed Ubuntu 12.04 64-bit selecting "UEFI: general" boot entry. Installation type: Something Else Created partition /sda5 mount as /, /sda6 mount as /home, /sda7 mount as swap Selected /dev/sda for boot loader installation. Other options are /dev/sda, /dev/sda1/dev/sda3 Windows 7 (loader) ... Grub comes up with 6 entries Ubuntu - this runs great Linux 3.2.0-29-generic recovery mode: mode hangs with "fb: conflicting fb hw usae interdrnfb vs EFI VGA - removing generic adapter" memtest86:erro: unknown command `linux 16' memtest86 serial: unknown command `linux 16' Windows 7 (loader) (on /dev/sda3): invalid EFI file path Windows Recovery Environment (on /dev/sda8): unknown command drivemap, invalid EFI file path. My workaround for booting Windows 7 is hitting ESC during boot, windows boot manager comes up and * for booting into Windows 7 I select "WIndows Boot Manager (PO: SanDisk ....". * for booting into Ubuntu I select ubuntu (P0: SanDisk...) How can I boot into Windows from Grub?

  Read the article

• Capital D key not working / producing output

  - by Jonathan

  For some inexplicable reason the capital d key on my Ubuntu system is no longer producing output. Hitting caps lock and then d produces a D. I've tried multiple keyboards and the issue is the same. There's nothing bound to Shift+d under System Preferences Keyboard Shortcuts. xev produces the following: shift + a KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31268952, (130,-16), root:(1000,525), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269376, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XmbLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269584, (130,-16), root:(1000,525), state 0x11, keycode 38 (keysym 0x41, A), same_screen YES, XLookupString gives 1 bytes: (41) "A" XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31269608, (130,-16), root:(1000,525), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False shift + d KeyPress event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31102792, (115,-13), root:(985,528), state 0x10, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False FocusOut event, serial 36, synthetic NO, window 0x4c00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 36, synthetic NO, window 0x4c00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 36, synthetic NO, window 0x0, keys: 2 0 0 0 0 0 0 64 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 KeyRelease event, serial 36, synthetic NO, window 0x4c00001, root 0x27a, subw 0x0, time 31103104, (115,-13), root:(985,528), state 0x11, keycode 62 (keysym 0xffe2, Shift_R), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

  Read the article

• Problem with APTonCD application

  - by Harikrishnan

  I created a iso image using aptoncd & burned it to a dvd. now when i tried to restore, the program does not detect the dvd in the drive. It shows "Please insert a disc in the drive." and if we click "ok" it shows "E: Failed to mount the cdrom.". The dvd is in the drive itself. I tried "sudo lshw -C disk" and the out put is: *-cdrom description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 1 bus info: scsi@1:0.0.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd0 logical name: /dev/sr0 logical name: /media/APTonCD logical name: /media/apt version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted status=ready *-medium physical id: 0 logical name: /dev/cdrom logical name: /media/APTonCD logical name: /media/apt configuration: mount.fstype=iso9660 mount.options=ro,relatime,uid=1000,gid=1000,iocharset=utf8,mode=0400,dmode=0500 state=mounted Then i checked in disk utility application. in that dvd rom is shown as "/dvd/sr0". my ubuntu version is 10.10. please help me to solve the problem.

  Read the article

• Configuration Tips for better Performance with ADF Mobile Apps

  - by SRINI INDLA

  Some tips to keep in mind to make sure ADF Mobile application's performance is optimal: 1. Select release mode in deployment profile. This is perhaps the most important thing to remember to ensure best performance for ADF Mobile Apps. Selecting this option causes the deployer to package optimized JVM and minified JS libs with the mobile app there by significantly improving the over all performance of the application. 2. For iOS you do not need to do anything else other than selecting  release mode in deploy profile. However, on Android you have to create a keystore and configure it in JDev --> Tools --> Preferences --> ADF Mobile --> Platforms : Android as shown in the snapshot below 3. Steps for generating the Keystore for Android using keytool :  4. Logging level setting in logging.properties: Make sure the log level is set to SEVERE for both framework logger as well as the application logger as follows oracle.adfmf.framework.level=SEVERE oracle.adfmf.application.level=SEVERE 5. When using SOAP WebServices with WebService Data Control make sure you select the option to copy the WSDL. This will cause the JDev to download the WSDL and all the XSDs referenced by the WSDL from the server at design time and package them with the application during deployment. This way the application does not incur the cost of downloading these resources at run time from the device.

  Read the article

• Ubuntu won't load, freezes on purple screen

  - by kara

  Last time I restarted my computer, I could not get Ubuntu to load; the screen would either go black, or would hang at the purple screen indefinitely. I have had some graphics problems in the past, but had put 'nomodeset' after 'quiet splash' in the grub command line, which at least let Ubuntu load. That doesn't work now, and doesn't work if I remove it. I looked up some answers, such as this one: Purple start screen - no splash screen However, when I enter the root in recovery mode in grub, I always get errors when I run those command lines and it won't let me modify the files. Also, if I run in recovery mode and then choose 'resume normal boot', it will continue. But instead of getting a usual interface, I get a black screen that asks for my username and password. I enter these, and it tells me I'm in Ubuntu 12.04, but I'm still on a black screen with texts. It also informs me that there are updates to install. When I use the command 'sudo apt-get update', it starts to retrieve the information, but then the screen goes blank after a couple of seconds and I can't do anything anymore. Any ideas?

  Read the article

• Precise: Evolution laggy due to IMAP -profile or due to some odd Sync -issue?

  - by Izzy

  I'm fighting with Evolution. Basically it's working fine -- but it is very slow to react in certain situations. There is apparently some problem with syncing and IMAP. Helper questios Could be that changing away from Bonobo has to do with slowing-down? There might be some trouble with the new engine and "asynchronous actions". What to do about it? I want to get the previous "working mood" back. How can I speed this thing up? Different scenarios when sending a mail, the composer window hangs there inactive for a couple of seconds, everything grayed out. Though there is a green check mark saying it's sent, I'm not sure a) why it's still blocking everything and b) whether I could simply close it without "breaking"/"losing" anything. In earlier versions, the composer window was closing pretty fast, and one could see the message being stored into the local "outbox" until it was sent, and one could immediately continue with the next task. I prefer that behaviour over the current. switching between modules. Coming from mail and switching to the address book takes a couple of seconds. Same for switching to the calendar. I read about different "possible causes" and tried a few things: I only have 3 local address books, so no networking should be involved here. To make sure, I switched to offline mode and then tried to access the address book. No noticeable difference. I use 3 Google Calendars. Switching to offline mode made a minor difference, but so minor that it also could be "imagination" since one might have expected this in this case according to some reports, disabling the tasks should help. Well, it didn't in my case, as I don't use them regularly (just two local items stored here)

  Read the article

• New to emacs -- my key bindings are different from what is described in the tutorials. How to fix this?

  - by MountainX

  I'm using emacs v24 [GNU Emacs 24.0.94.1 (x86_64-pc-linux-gnu, GTK+ Version 3.3.20) of 2012-03-26 on meitnerium, modified by Debian] on Kubuntu 12.04. My basic problem is that emacs is not behaving the same as the tutorials I'm reading. I either need different tutorials or I need to make my emacs work as described in the tutorials. Being new to emacs and KDE, I don't know where to start because of this incongruence. My specific problem is this: When I shift-left-mouse-click, I get a buffer dialog popup. That differs from my understanding of the documenation: shift mouse-1 Draws lines, rectangles or poly-lines, erases, cuts, copies or pastes. I also want to use CUA mode. The CUA mode documents seem to indicate that shift-left-mouse-click produces: rectangle highlighting by dragging the mouse while holding down the shift key. I don't get that result either. In fact, I can't select using any modifier keys together with a drag action. Maybe this is a KDE issue. I don't know.

  Read the article

• Great tools to demonstrate and showcase the ODA appliance

  - by user12842161

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:Calibri; mso-fareast-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} 1. Introduction to the Oracle Database Appliance Video http://www.youtube.com/watch?v=DU0hCO_-q-8 2. Oracle Database Appliance Configurator (run in standalone mode on your PC for mode) http://www.oracle.com/technetwork/server-storage/database-appliance/oracle-database-appliance-manager-1352946.zip 3. Oracle Database Appliance 3D Demo http://oracle.com.edgesuite.net/producttours/3d/databaseappliance/

  Read the article

• Virtualbox install 12.04 guest: "pae not present"

  - by Peter.O

  I get this message while trying to install Ubuntu 12.04 as a guest in VirutalBox 4.1.18, on an Ubuntu 10.04 host. This kernel requires the following feature not present on the CPU: pae Some host specs: The host's kernel is: Linux 2.6.32-41-generic-pae GNU/Linux lscpu (host): Architecture: i686, CPU op-mode(s): 32-bit, 64-bit grep --color=always -i PAE /proc/cpuinfo   does show pae in its output. The 12.04 iso used is: ubuntu-12.04.0-desktop-i386.iso As a comparison/check, I downloaded and installed Linux Mint 13 Cinnamon to the same host on the exact same VM (I just changed the .iso image). It worked fine. Its iso is: linuxmint-13-cinnamon-dvd-32bit.iso It seems (to me) that I have pae.. what is going on here? Update: I had assumed that Linux Mint also required pae (being Ubuntu based), but I've just run;   grep --color=always -i PAE /proc/cpuinfo   in the Mint VM.   It showed no output.   So it seems the issue may lie with VirtualBox.   If that is the case, how can I get Virtualbox into pae mode?

  Read the article

• My wireless has suddenly became disabled by hardware switch, BIOS, rfkill, fn+f8 do nothing

  - by cwwk

  I have a toshiba l655d-s5145. There is no physical toggle for the wireless, although the f8 key is supposed to do the trick. It doesn't. The wireless has been working since October, and suddenly, nothing. RFKILL reports that the wireless is hard blocked, but unblock wifi, unblock 0, unblock all do nothing. I inserted a usb dongle, and that is also disabled by hardware switch, although rfkill reports that it is neither hard nor soft blocked. My onboard wireless is 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) according to lspci. Lsmod reports that these drivers are loaded. rtl8192c_common 75767 1 rtl8192ce rtlwifi 110972 1 rtl8192ce I resorted to reformatting the drive and reinstalling, but that also did not work. In BIOS I restored system defaults as there is no specific entry for wifi. Before reinstalling a pure xubuntu I went into Unity and saw that the airplane mode was on and despite being toggled off, it returned to the on position. I'm not sure where to find airplane mode in Xubuntu. What else can I do? I need my wireless.

  Read the article

• How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

  - by MoLE

  I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

  Read the article

• Bluetooth mouse no longer paired after resuming from suspend since upgrading to 13.10

  - by Korakys

  Since upgrading to 13.10 from 13.04 my mouse no longer connects via bluetooth. In settings it states that the mouse is not paired. Restarting bluetooth with sudo /etc/init.d/bluetooth restart does not help. Restarting the computer does fix the problem if bluetooth is restarted also with the previously mentioned command, but this is not ideal. The mouse worked fine prior to updating to 13.10. The computer is a ThinkPad X230 with a Broadcom 'BCM20702A0' bluetooth module (I think). When it is not working hciconfig hci0 -a returns: hci0: Type: BR/EDR Bus: USB BD Address: C0:18:85:DB:F3:D1 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN RX bytes:766129 acl:49888 sco:0 events:2233 errors:0 TX bytes:5953 acl:240 sco:0 commands:274 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'BCM20702A' Class: 0x6e0100 Service Classes: Networking, Rendering, Capturing, Audio, Telephony Device Class: Computer, Uncategorized HCI Version: 4.0 (0x6) Revision: 0x1000 LMP Version: 4.0 (0x6) Subversion: 0x220e Manufacturer: Broadcom Corporation (15) When it is working hciconfig hci0 -a returns: hci0: Type: BR/EDR Bus: USB BD Address: C0:18:85:DB:F3:D1 ACL MTU: 1021:8 SCO MTU: 64:1 UP RUNNING PSCAN RX bytes:253334 acl:16391 sco:0 events:842 errors:0 TX bytes:2519 acl:65 sco:0 commands:84 errors:0 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 Link policy: RSWITCH SNIFF Link mode: SLAVE ACCEPT Name: 'ubuntu-0' Class: 0x6e0100 Service Classes: Networking, Rendering, Capturing, Audio, Telephony Device Class: Computer, Uncategorized HCI Version: 4.0 (0x6) Revision: 0x1000 LMP Version: 4.0 (0x6) Subversion: 0x220e Manufacturer: Broadcom Corporation (15) I am a relative novice with linux so don't ask me compile anything please, but I can use google.

  Read the article

• Splitting Pygame functionality between classes or modules?

  - by sec_goat

  I am attempting to make my pygame application more modular so that different functionalities are split up into different classes and modules. I am having some trouble getting pygame to allow me to draw or load images in secondary classes when the display has been set and pygame.init() has been done in my main class. I have typically used C# and XNA to accomplish this sort of behavior, but this time I need to use python. How do I init pygame in class1, then create an instance of class2 which loads and converts() images. I have tried pygame.init() in class 2 but then it tells me no display mode has been set, when it has been set in class1. I am under the impression i do not wnat to create multiple pygame.displays as that gets problematic I am probably missing something pythonic and simple but I am not sure what. How do I create a Display class, init python and then have other modules do my work like loading images, fonts etc.? here is the simplest version of what I am doing: class1: def __init__(self): self.screen = pygame.display.set_mode((600,400)) self.imageLoader = class2() class2: def __init__(self): self.images = ['list of images'] def load_images(): self.images = os.listdir('./images/') #get all images in the images directory for img in self.images: #read all images in the directory and load them into pygame new_img = pygame.image.load(os.path.join('images', img)).convert() scale_img = pygame.transform.scale(new_img, (pygame.display.Info().current_w, pygame.display.Info().current_h)) self.images.append(scale_img) if __name__ == "__main__": c1 = class1() c1.imageLoader.load_images() Of course when it tries to load an convert the images it tells me pygame has not been initialized, so i throw in a pygame.init() in class2 ( i have heard it is safe to init multiple times) and then the error goes to pygame.error: No video mode has been set

  Read the article

• Can I use standard tools to get the full name of a process, when its name has embedded spaces?

  - by fred.bear

  I understand that it may be a rare situation for an executable to have spaces in it, but it could happen. An example may be the best explanation.. Using standard tools, I want to determine the location (on the file system) of the executable which owns(?) the current window... get the current window ID ...(xdotool getactivewindow ) use the ID to get the PID ...(wmctrl -p -l | sed ... ID .... use the PID to get the executable's name ... (ps -A ... here is where I run into problems ! Whith ps, when listing only the executable's name (-o ucmd), it truncates the name to 15 characters, so this rules out this option for any name which is longer. Widening the column (-o ucmd:99 ) makes no difference.. If pgrep is anything to go by, its matching is limited to 15 because of stat (see: info pgrep).. Listings in variants of "full" mode (eg -A w w) are not useful when the name concerned has spaces in it, because this name is separated from its args by another space!.. Also, in "full" mode, if the process was started by a link, the name of the link is shown, rather than the executable's name. Is there some way to do this (using standard tools)? ...or are spaces a show stopper here?

  Read the article

• How to fix Black screen?

  - by stupidwhiteguy

  so I recently had my question deleted and merged into a standard how to for blank screens. I am relatively new to This type of computer work and i don't understand the steps nessary to diagnose my problem well enough to solve it so this help full how to has me feeling helpless I can use Ctrl + Alt +F1 and log in So how do I use sudo commands to fix the blank screen on my old dell? sudo lsoci -nn tells me my video card is a ATI rage 128 pro ultra tf /var/log/Xorg.0.log tells me Permission denied that is all i get Sudo apt-get install --reinstall unity tried thay also have also tried Apt-get update and upgrade Please dont close this question without providing an actual answer or if you think it is an exact duplicate provide a solution that worked for that question. I see a lot of these questions as closed and there is no real answer given I will try any solutions available and report results so that others can also solve problems not be overwhelmed by overly broad troubleshooting guides that do nothing to help solve specific issues The nomodeset change from quiet splash also yields no results on reboot I still get a blank screen this screen still has contorl alt f1 abilities but that is it contorl alt f8 causes blinking cursor and F7 gets a crazy flash with green and blue then blank screen Contorl alt f1 a log in prompt in text only when run in recovery mode with failsafe graphics its says the syestem is running in low graphics mode your screen graphics card and input device settings could not be detected correctly. You will need to configure these your self how do i do that? I got this /var/log/failsafeX-backup-120909200641.tar as the location of my log files but i have no idea how to axcess sounds work in blank screen also screen responds or flashes after log in is typed and password entered really any help is good I don't even know where to start I believe 12.04 is installed and functioning but i don't think I can see it at the end of the error log it says error setting mtrr (base= oxf0000000, size= 0x01000000, type=1) inappropriate ioctl for device(25) i have tried to provide as much info as I understand how to provide

  Read the article

• Laptop power button not working

  - by DyP

  I have a (seemingly rather exotic) Dell Latitude XT2 notebook running Lubuntu 12.04, fresh install. Tried to get the power button to work as expected (opening lubuntu-logout, just as I think it was meant to be out-of-the box), but no success: power button does nothing but forced power-off on long press. Here some more information, please ask if something more could help: Power button is recognized as a device: xinput lists Power Button as a slave keyboard at /dev/input/event1, and I can run a tool to listen to that device and invoke some action (successfully). But using .config/openbox/lubuntu-rc.xml to assign some action to XF86ShutDown or XF86PowerOff does nothing. Works well for any key of the keyboard. xinput --test reports a keycode (key press, key release) of 124 when pressing & releasing the power button. xmodmap -pk lists 124 mapped to XF86PowerOff which seems correct to me (btw: is this the same as XF86ShutDown?) When assigning another keysymname to the 124 keycode, e.g. 'w', still nothing happens when pressing the power button (no window seems to receive a 'w'). Works well for any key on the keyboard. The outputs of xev for a press/release of the power button irritate me: MappingNotify event, serial 41, synthetic NO, window 0x0, request MappingKeyboard, first_keycode 8, count 248 FocusOut event, serial 41, synthetic NO, window 0x2a00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 41, synthetic NO, window 0x2a00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 41, synthetic NO, window 0x0, keys: 93 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (instead of 93, I also get different values) I might have missed something very basic since I'm not very familiar with both openbox/lubuntu and the X input system. Btw.: same goes for three other special buttons on my laptop..

  Read the article

• how do I uninstall old kernel options listed in Grub2? [closed]

  - by user12809

  Possible Duplicate: Is there a way to remove/hide old kernel versions? I installed Ubuntu Tweak in Ubuntu 11.10, went to Janitor, and selected and removed old kernels that appeared there (3.0.0-12). Now, the only installed linux-image that appears as 'Installed' in SPM is the most recent one (3.0.0-13), which is the one I want. It did not however eliminate the kernel listing in Grub 2. At boot: However, at boot, in Grub-2, the following options still appear: 3.0.0-13-generic 3.0.0-13-generic (recovery mode) 3.0.0-12 (generic) (on /dev/sde5) 3.0.0-12 (generic (recovery mode) (on /dev/sde5) And, in Terminal, when I change directory (cd) to /boot, and then list (ls), I get the following listed kernels: 3.0.0-13 2.6.38-12 2.6.38-8 (al There is no change when I sudo update-grub in Terminal 1) what is /dev/sde5, and where is it located in the file system, so i can delete it? 2) why the differences between what appears as installed in SPM, what appears at boot in Grub2, and what shows when I list the contents of Grub2 in Terminal? Ultimately, I simply want to remove the 3.0.0-12 kernel options at boot in Grub2. How do I best and simplest do that? Thanks again donofrij is online now Report Post Edit/Delete Message Reply With Quote Multi-Quote This Message Quick reply to this message

  Read the article

• How can I install from a 9.04 live USB/DVD?

  - by bstpierre

  I have a 9.04 (Jaunty) ISO burned to a USB stick; it appears to be a "live DVD". When I boot from it, I get a GRUB menu listing: Ubuntu, with Linux 2.6.35-generic (This matches the system currently installed on the HDD?) Ubuntu, with Linux 2.6.35-generic (recovery mode) Memory test Ubuntu 9.04, kernel 2.6.28-11-generic (on /dev/sda1) Ubuntu 9.04, kernel 2.6.28-11-generic (recovery mode) (on /dev/sda1) Ubuntu 9.04, memtest86+ (on /dev/sda1) When I select Ubuntu 9.04, kernel 2.6.28-11-generic (on /dev/sda1), I arrive at the desktop of a 9.04 system. I want to wipe the HDD clean and install 9.04. (Upgrading to something newer is not an option; this version is required by a legacy application.) How can I install from this live USB image? I vaguely remember some incantation that I should be able to use in the booted system, but my google-fu is broken at the moment. I'm comfortable with low-level commands, so if you want to recommend a more hard-core strategy, I'm willing to roll with it without requiring a ton of detail...

  Read the article

• New Versions of Whitepapers are available

  - by Anthony Shorten

  The set of whitepapers that are available are progressively being updated and republished to reflect new versions of the products as well new advice for existing customers. A number of whitepapers are now available that have been updated (the My Oracle Support Doc Id is indicated): What’s New in Oracle Utilities Application Framework V4 (Doc Id: 1177265.1) -  This has been updated for the latest facilities in Oracle Utilities Application Framework V4.1. Batch Best Practices (Doc Id: 836362.1) – This has been updated for newer advice including more details of how CLUSTERED mode works, how to migrate to CLUSTERED mode and some configuration examples to cover typical configuration scenarios. Oracle Utilities Application Framework Architecture Guidelines (Doc Id: 807068.1) – This has been updated to reflect additional architecture advice. Performance Troubleshooting Guides (Doc Id: 560382.1) – This has been updated for the latest facilities in Oracle Utilities Application Framework V4.1 and includes additional techniques that have been used by customers to track performance. The whitepapers apply to all Oracle Utilities Application Framework Products which at the present time includes: Oracle Utilities Customer Care And Billing (V2.x) Oracle Enterprise Taxation Management (V2.x) Oracle Utilities Business Intelligence (V2.x) Oracle Utilities Meter Data Management (V2.x) Oracle Utilities Mobile Workforce Management (V2.x) Oracle Utilities Smart Grid Gateway (V2.x) Additional whitepapers and updates will be posted as they are available.

  Read the article

• Problem with scrolling background in one OpenGL loop

  - by GvS

  I have 960x3000 map image in png and I'm scrolling it in a loop like this (it's called in 60 FPS loop): glPushMatrix(); glBindTexture( GL_TEXTURE_2D, mapTex[iBgImg]); glBegin(GL_QUADS); double mtstart = 0.0f - fBgVPos/(double)BgSize; double mtend = mtstart + mtsize; glTexCoord2d(0.0, mtstart); glVertex2f(fBgX, TOP_MARGIN); glTexCoord2d(1.0, mtstart); glVertex2f(fBgX + MAP_WIDTH, TOP_MARGIN); glTexCoord2d(1.0, mtend); glVertex2f(fBgX + MAP_WIDTH, BOTTOM_MARGIN); glTexCoord2d(0.0, mtend); glVertex2f(fBgX, BOTTOM_MARGIN); glEnd(); glPopMatrix(); unfortunately it isn't smooth when the game is in windowed mode. However, it is smooth in full screen mode. I'm using GLFW for windows. Maybe there is something wrong with my method? Is there anything better? Or could this be hardware problem? Edit: Window is created using glfwOpenWindowHint(GLFW_WINDOW_NO_RESIZE, GL_TRUE); glfwOpenWindowHint(GLFW_REFRESH_RATE, 60); and main loop is using glfwSwapInterval(1) to ensure 60 FPS;

  Read the article

• after BIOS splash, will not boot -- asks me to select an OS, but it just reboots

  - by user92040

  I'm running Linux Mint 13 MATE 64-bit. Everything has been working for several weeks. Yesterday, when I tried to boot up my computer, after the BIOS screen flashes I reach a screen with a black background that reads at the top: GNU GRUB version1.99-21ubuntu3.4 Then there is a box in which I can select from the following lines: Linux Mint 13 MATE 64-bit, 3.2.0-31-generic (/dev/sdb2) Linux Mint 13 MATE 64-bit, 3.2.0-31-generic (/dev/sdb2) -- recovery mode Previous Linux versions Memory test (memtest86+) Memory test (memtest86+, serial console 115200) At the bottom it reads: Use the ? and ? keys to select which entry is highlighed. Press enter to boot the selected OS, 'e' to edit the commands before booting or 'c' for a command-line. I have no idea why it started doing this and, worse, I have no idea how to get out of here. No matter which option I select, I can't get it to boot the OS. If I select either of the first two, it reboots to splash the BIOS and then I'm right back where I started. If I choose "Previous Linux versions" I get essentially the same screen with only two choices (which are the same as the first two choices listed above, Linux 13 MATE and the recovery mode). Again, choosing either one of those results in a reboot. If I try to run either of the memtest options, it reads: error: unknown command 'linux16', Press any key to continue... Then it brings me back to the same screen Can anyone help me please? Intel Core i5-2500 ASUS P8Z68-V LX Intel Motherboard G. Skill Ripjaws series F3-12800CL9D-8GBRL (4GB x2) Plextor 128GB M5S Series SSD

  Read the article

• how to override ckeditor events [migrated]

  - by joe

  I am new to ckeditor, I have hard time figuring this issue out. due to my html design; if I try to use the link editor dialog while my ckeditor is maximized, it just doesn't show up, I understand that ckeditor is the top most object in my html page and the link dialog comes underneath it. if now I bring ckeditor to its normal state I will be able to see and use the link dialog. my idea is to slightly override the link button click event as follows: if the editor is in full screen mode, bring it back to the normal state. and keep a flag somewhere so that when I close the link dialog, I can decide whether to bring back the ckeditor to a maximized mode again. now this is easy logic except that I do not know how to override the click event of the link button and keep it work as expected. here's what I have: $().ready(function () { var editor = $('#txa').ckeditor(); CKEDITOR.plugins.registered['link']= { init : function( editor ) { var command = editor.addCommand( 'link', { modes : { wysiwyg:1, source:1 }, exec : function( editor ) { if(editor.commands.maximize.state == 1 ){ alert("maximized"); //....here bring back the editor to UN-maximized state and let the link button event click do the default behavior } else { alert("normal state"); } //2 is normal state //1 is maximized } } ); editor.ui.addButton( 'link',{label : 'YOUR LABEL',command : 'link'}); } } }); html part to make the exemple work: <div> <textarea id="txa"> </textarea> </div> TO BE SHORT: http://jsfiddle.net/Q43QP/ if the editor is maximized, bring it to normal state then show the link dialog.

  Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >