Search Results

Search found 4775 results on 191 pages for 'trace flags'.

Page 127/191 | < Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >

• Two DHCP interfaces asigned to two default gateways to OS

  - by user140600

  I have a Ubuntu box that has two networking interfaces (eth0 and wlan0). They are both configured for DHCP in /etc/network/interfaces, but they both assign a default gateway: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto wlan0 iface wlan0 inet dhcp wireless-essid test Result of route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.1.1 0.0.0.0 UG 100 0 0 wlan0 0.0.0.0 10.0.0.1 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 172.16.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 How can I set up /etc/network/interfaces to have only one default gateway, on the interface I want? Worst case scenario, how can I at least control which one gets on top on the route -n command, each boot? Note: This box will travel a lot, and will be connected to different networks, so I don´t know in advance the IP addresses/ranges it will have. Sometimes the default gw interface will be eth0. Sometimes it will be wlan0 ... So, this needs to be kind of automatic ...

  Read the article

• Disable Certain Firefox Plugins System-wide by Default

  - by Andrew Case

  I have firefox installed system-wide for all our users. Unfortunately the Adobe Reader Plug-in is rather flakey and doesn't work some of the time. As a result I want to disable the plug-in by default for all our users, but still allow them to enable it if they want via the standard Tools-Add-ons-Plug-ins menu option. How can I have this plug-ins enabled/disabled status be disabled by default? I've been able to configure system-wide configurations before by setting preferences in the mozilla root folder file defaults/pref/all.js, but enabled/disabled plugins doesn't appear to be configured in the preferences. [edit 1]: I found 'How to manage firefox plugins in pluginreg.dat file' which explained some of the formatting of the pluginreg.dat file. From there I could see flags are masked as follows (from nsPluginHostImpl.h): #define NS_PLUGIN_FLAG_ENABLED 0x0001 // is this plugin enabled? #define NS_PLUGIN_FLAG_OLDSCHOOL 0x0002 // is this a pre-xpcom plugin? #define NS_PLUGIN_FLAG_FROMCACHE 0x0004 // this plugintag info was loaded from cache #define NS_PLUGIN_FLAG_UNWANTED 0x0008 // this is an unwanted plugin #define NS_PLUGIN_FLAG_BLOCKLISTED 0x0010 // this is a blocklisted plugin But is there a way to add this to the defaults so that that NS_PLUGIN_FLAG_ENABLED is removed by default?

  Read the article

• Wake for Network Access Apache servr in OS X 10.8, followup

  - by Gary

  Sorry, I can't seem to post this response within the same thread. Thank you both (Zoredache and Gordon) for your answer. But the fix seems temporary. I entered the command you suggested, and it seemed to work: ...smith$ Registering Service ApacheNoDoz._http._tcp.local port 80 DATE: ---Fri 14 Sep 2012--- 12:04:15.813 ...STARTING... 12:04:16.566 Got a reply for service ApacheNoDoz._http._tcp.local.: Name now registered and active So, I checked for it on my G5: Browsing for _http._tcp Timestamp.....A/R Flags if Domain......Service Type...Instance Name (lots of Bonjour printers omitted)... 12:07:38.370..Add.....2..4 local.......... _http._tcp.........ApacheNoDoz 12:07:45.921..Rmv.....0..4 local..........._http._tcp.........ApacheNoDoz So, it was running at 12:07:38, at which time the host was asleep. But, shortly after, the activity seems to have been removed. I don't know why. Does this mean that I can never let the cpu sleep, or is there something else I have to set? Thanks, again.

  Read the article

• Queries passed to SQL Server are getting corrupted

  - by adrianbanks

  We are experiencing a bizarre error with our application at a customer site. We have managed to narrow it down to the point where we can replicate the behaviour using just Management Studio and SQL Server. We have two machines, A and B: +------------+ +--------------------+ | [A] | | [B] | | Management | -------------- | SQL Server 2008 R2 | | Studio | | Enterprise x64 | +------------+ +--------------------+ We are running a SQL script in Management Studio on machine A against the SQL Server instance on machine B. We are not actually executing the script, just parsing it. Most of the time, the parse operation works fine. Occasionally (seemingly randomly), the parse operation fails with a syntax error. The error message shows the part of the script with the error, which appears as some SQL from the original script that has been truncated and has random characters appended to it. An example: The original SQL: SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = ST.TABLE_NAME WHERE ST.TABLE_TYPE = 'BASE TABLE' AND SC.COLUMN_NAME = 'Identity' AND ST.TABLE_NAME != 'dtproperties' ORDER BY ST.TABLE_NAME The SQL that is in error (as reported by SQL Server): SELECT DISTINCT ST.TABLE_NAME as TableName FROM INFORMATION_SCHEMA.TABLES AS ST INNER JOIN INFORMATION_SCHEMA.COLUMNS AS SC ON SC.TABLE_NAME = Sa? The above example shows how the query is being corrupted. It doesn't always happen, and is not always the same bit of SQL that causes the error. Parsing this script against another SQL Server instance produces no errors, showing that the script is fine. It appears that something is corrupting the SQL that is being received the the server. This leads me to think that the problem lies either with the client end or in the transmission of the SQL from the client to the server. I have a SQL trace from the period where an error occurs, which shows the SQL has been corrupted when SQL Server receives it. We have been unable to track down any possible cause of this behaviour, and so cannot find a fix. Because the errors occur seemingly randomly, it is also very hard to generate reproduction steps to submit a bug report. Any ideas?

  Read the article

• "Can't find root filesystem / error mounting /dev/root" when booting to new kernel

  - by salparadise

  I am trying to upgrade my kernel from 2.6.18-274 to 2.6.39 for some wireless card drivers. When I boot into the new kernel I get the "Can't find root filesystem / error mounting /dev/root" googling led me to this page http://fedoraproject.org/wiki/Common_kernel_problems#Can.27t_find_root_filesystem_.2F_error_mounting_.2Fdev.2Froot From what I am reading seems to be an issue with a driver for my SATA controller or HD, but I can't find what option I need to add to the kernel. Doing a diff from the old initrd to the new one gives me the following: root-> diff /tmp/kafter /tmp/kbefore 6a7,8 > lib/dm-message.ko > lib/dm-region_hash.ko 8a11 > lib/dm-raid45.ko 13d15 < lib/dm-region-hash.ko 16a19 > lib/dm-mem-cache.ko Do I need any of those? not sure if I would need dm-raid45.ko as I am not running a raid. I have the same SATA and IDE options configured for both kernels so not sure what else to look for, any help is appreciated. Additionally here is the HW info: 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: Hewlett-Packard Company Unknown device 3006 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 233 I/O ports at 1818 [size=8] I/O ports at 1830 [size=4] I/O ports at 1820 [size=8] I/O ports at 1834 [size=4] I/O ports at 14f0 [size=16] Capabilities: [70] Power Management version 2 root-> smartctl -a /dev/sda ... === START OF INFORMATION SECTION === Device Model: WDC WD5000AADS-00S9B0

  Read the article

• How can I "filter" postfix-generated bounce messages?

  - by Flimzy

  We are using postfix 2.7 and custom SMTPD (based on qpsmtpd) in highly customized configuration for spam filtering. We have a new requirement to filter postfix-generated bounces through our custom qpsmtpd process (not so much for content filtering, but to process these bounces accordingly). Our current configuration looks (in part) like this: main.cf (only customizations shown): 2526 inet n - - - 0 cleanup pickup fifo n - - 60 1 pickup -o content_filter=smtp:127.0.0.2 Our smtpd injects messages to postfix on port 2526, by speaking directly to the cleanup daemon. And the custom pickup command instructs postfix to hand off all locally-generated mail (from cron, nagios, or other custom scripts) to our custom smtpd. The problem is that this configuration does not affect postfix generated bounce messages, since they do not go through the pickup daemon. I have tried adding the same content_filter option to the bounce daemon commands, but it does not seem to have any effect: bounce unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 defer unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 trace unix - - - - 0 bounce -o content_filter=smtp:127.0.0.2 For reference, here is my main.cf file, as well: biff = no # TLS parameters smtpd_tls_loglevel = 0 smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${queue_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${queue_directory}/smtp_scache smtp_tls_security_level = may mydestination = $myhostname alias_maps = proxy:pgsql:/etc/postfix/dc-aliases.cf transport_maps = proxy:pgsql:/etc/postfix/dc-transport.cf # This is enforced on incoming mail by QPSMTPD, so this is simply # the upper possible bound (also enforced in defaults.pl) message_size_limit = 262144000 mailbox_size_limit = 0 # We do our own message expiration, but if we set this to 0, then postfix # will try each mail delivery only once, so instead we set it to 100 days # (which is the max postfix seems to support) maximal_queue_lifetime = 100d hash_queue_depth = 1 hash_queue_names = deferred, defer, hold I also tried adding the internal_mail_filter_classes option to main.cf, but also tono affect: internal_mail_filter_classes = bounce,notify I am open to any suggestions, including handling our current content-filtering-loop in a different way. If it's not clear what I'm asking, please let me know, and I can try to clarify.

  Read the article

• How to install/configure ffmpeg to compress mp4 videos for flash player delivery?

  - by Andrew Fulton

  We have a flash web-app that created interactive video, and are using ffmpeg to do some compression/resizing when a user "publishes" their project. The user can upload flv files and mp4 files, both of which play fine in the Flash UI before publishing. After publishing the flv files work fine, but the mp4 files will not play in the flash player: Audio will play but video won't. The mp4 files will play fine if I download them and play them in the Quicktime player but if I attempt to open them in the Adobe Media Player it reports "The media file does not contain a supported video track". If I open the Movie inspector in quicktime it tells me that the original file is an "h264" video and the ffmpeg-processed ones are "mpeg-4". I have tried forcing it to h264 by adding flags like -f h264 and -vcodec h264 but I get a screenfull of errors (no frame, illegal POC type, sps_id out of range) ending with Could not find codec parameters (Video: h264) h264 will show up if I run ffmpeg -formats and ffmpeg -codecs, and as I said it will play fine in Quicktime. Is there anything else I need to do to convince the flash player to play them? Is there anything else I need to tell you about the server that will help?

  Read the article

• jdbc4 CommunicationsException

  - by letronje

  I have a machine running a java app talking to a mysql instance running on the same instance. the app uses jdbc4 drivers from mysql. I keep getting com.mysql.jdbc.exceptions.jdbc4.CommunicationsException at random times. Here is the whole message. Could not open JDBC Connection for transaction; nested exception is com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: The last packet successfully received from the server was25899 milliseconds ago.The last packet sent successfully to the server was 25899 milliseconds ago, which is longer than the server configured value of 'wait_timeout'. You should consider either expiring and/or testing connection validity before use in your application, increasing the server configured values for client timeouts, or using the Connector/J connection property 'autoReconnect=true' to avoid this problem. For mysql, the value of global 'wait_timeout' and 'interactive_timeout' is set to 3600 seconds and 'connect_timeout' is set to 60 secs. the wait timeout value is much higher than the 26 secs(25899 msecs). mentioned in the exception trace. I use dbcp for connection pooling and here is spring bean config for the datasource. <bean id="dataSource" destroy-method="close" class="org.apache.commons.dbcp.BasicDataSource" > <property name="driverClassName" value="com.mysql.jdbc.Driver"/> <property name="url" value="jdbc:mysql://localhost:3306/db"/> <property name="username" value="xxx"/> <property name="password" value="xxx" /> <property name="poolPreparedStatements" value="false" /> <property name="maxActive" value="3" /> <property name="maxIdle" value="3" /> </bean> Any idea why this could be happening? Will using c3p0 solve the problem ?

  Read the article

• trying to route between two openvpn clients

  - by user42055

  I have two openvpn clients on the 10.0.1.0 (client1) and 192.168.0.0 (client2) subnets with the server's openvpn connection having the ip 192.168.150.1 The server has ip forwarding enabled. Currently, client1's vpn ip is 192.168.150.10 and the P-t-P ip is 192.168.150.9 I have created the following static route on client1: route add -net 10.0.1.0 netmask 255.255.255.0 gw 192.168.150.9 The routing table on client1 looks like this: Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.150.1 192.168.150.9 255.255.255.255 UGH 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 I thought this would be correct to allow traffic from client1 to reach computers on client2's network, but it does not work. Is 192.168.150.9 (the P-t-P address) the correct one to be routing through ? I tried using 192.168.150.1 but I couldn't create the route. I hope this is clear.

  Read the article

• Computing Number of Bits in Public Key

  - by eb80

  I am working with DKIM and trying to compute the public key size of some DKIM signatures. I know from tools that Gmail's is now 2048, but how could I have figured this out myself (i.e., what exact Linux commands and why)? user@host$ dig txt 20120113._domainkey.gmail.com ; <<>> DiG 9.8.3-P1 <<>> txt 20120113._domainkey.gmail.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 52228 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;20120113._domainkey.gmail.com. IN TXT ;; ANSWER SECTION: 20120113._domainkey.gmail.com. 300 IN TXT "k=rsa\; p=MIIBIjANBgkqhkiG9w0BAQEFAAOCAQ8AMIIBCgKCAQEA1Kd87/UeJjenpabgbFwh+eBCsSTrqmwIYYvywlbhbqoo2DymndFkbjOVIPIldNs/m40KF+yzMn1skyoxcTUGCQs8g3FgD2Ap3ZB5DekAo5wMmk4wimDO+U8QzI3SD0" "7y2+07wlNWwIt8svnxgdxGkVbbhzY8i+RQ9DpSVpPbF7ykQxtKXkv/ahW3KjViiAH+ghvvIhkx4xYSIc9oSwVmAl5OctMEeWUwg8Istjqz8BZeTWbf41fbNhte7Y+YqZOwq1Sd0DbvYAD9NOZK9vlfuac0598HY+vtSBczUiKERHv1yRbcaQtZFh5wtiRrN04BLUTD21MycBX5jYchHjPY/wIDAQAB" ;; Query time: 262 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Mon Nov 19 10:52:06 2012 ;; MSG SIZE rcvd: 462

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got fglrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci EDIT: fglrx 12.4 seems to work. Thing is, since I am on kernel 3.2, I need to apply this patch to common/lib/modules/fglrx/build_mod/firegl_public.c. I thought ATI dropped support for the 4xxx series after 12.4. Why doesn't 12.6 legacy work?

  Read the article

• iptables firewall rules not allowing ssh from lan to DMZ

  - by ageis23

  Chain INPUT (policy ACCEPT) target prot opt source destination REJECT tcp -- anywhere anywhere tcp dpt:www reject-with tcp-reset REJECT tcp -- anywhere anywhere tcp dpt:telnet reject-with tcp-reset ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED DROP udp -- anywhere anywhere udp dpt:route DROP udp -- anywhere anywhere udp dpt:route ACCEPT udp -- anywhere anywhere udp dpt:route logdrop icmp -- anywhere anywhere logdrop igmp -- anywhere anywhere ACCEPT udp -- anywhere anywhere udp dpt:5060 ACCEPT 0 -- anywhere anywhere state NEW logaccept 0 -- anywhere anywhere state NEW ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere logdrop 0 -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT 0 -- 192.168.0.0/24 192.168.2.0/24 reject-with icmp-port-unreachable ACCEPT tcp -- choister 192.168.2.142 tcp dpt:ssh state NEW REJECT 0 -- 192.168.0.0/24 192.168.3.0/24 reject-with icmp-port-unreachable ACCEPT gre -- 192.168.1.0/24 anywhere ACCEPT tcp -- 192.168.1.0/24 anywhere tcp dpt:1723 ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere TCPMSS tcp -- anywhere anywhere tcp flags:SYN,RST/SYN TCPMSS clamp to PMTU lan2wan 0 -- anywhere anywhere ACCEPT 0 -- anywhere anywhere state RELATED,ESTABLISHED logaccept tcp -- anywhere choister tcp dpt:www TRIGGER 0 -- anywhere anywhere TRIGGER type:in match:0 relate:0 trigger_out 0 -- anywhere anywhere logaccept 0 -- anywhere anywhere state NEW logdrop 0 -- anywhere anywhere The ssh server I'm trying to connect to is in the DMZ(192.168.0.145). It's mainly used as a web server. I need access to it from my room 192.168.2.142. I don't get why ssh can't forward onto the 192.168.2.0 subnet? I'm sure it's the reject rule that causing this because it works without it.

  Read the article

• Is there a clean way to obtain exclusive access to a physical partition under Windows?

  - by zneak

  Hey guys, I'm trying, under Windows 7, to run a virtual machine with VMWare Player from an OS installed on a physical partition. However, when I boot the virtual machine, VMWare Player says that it couldn't access the physical drive for writing. This seems to be a generally acknowledged problem in the VMWare community, as Windows Vista introduced a compelling new security feature that makes it impossible to write to a raw drive without obtaining exclusive access to it first. I have googled the issue and found a few workarounds. However, the clean ones seem to only work on whole physical disks, and not on partitions. So I would be left with the dirty solution. In short, it meddles with the MBR to erase any trace of the partitions to use, makes Windows forget about them, then restores the MBR so we can launch the VM. I'm not sure I want to do that. Is there a way to let VMWare acquire exclusive access to the partition without requiring me to nuke it away? What I'd be looking for, I suppose, is a way to put just partitions offline instead of whole physical drives.

  Read the article

• Different external ip addresses from different sites

  - by user630286

  My router is ClearOS 6(Centos 6). In my router, I have two external (internet) network connections from two ISP's. The primary connection is eth2 connected to a cable modem and the second one is ppp0 connected to a dsl modem. I have assigned eth2 as the primary connection (with a high metric value). In fact this is done through clearos's multiwan web interface. I have a test in my Nagios to monitor whether the primary connection. This connection is done based on the result of curl ifconfig.me But it seems that ifconfig.me is always giving the ip address of my secondary connection. I tested it through a browser. Yes ifconfig.me gives the secondary internet's(ppp0) ip address. But whatismyipaddress.[com|org] give my primary ip address (eth2). I checked the default route on the router through ip route list 0/0 which also shows the primary connection (eth2) as the default route. The traceroute www.google.com and traceroute ifconfig.me both seems to trace through the primary connection (eth2). As our secondary internet connection has only got a limited download, I don't want to end up having to pay a large sum at the end of the month. Has somebody got an idea why the ifconfig.me shows my secondary address? What is the best way to ensure that my router(and thus the lan) use the right internet connection.

  Read the article

• Disappeared graphics card

  - by lenovo user

  I have a Lenovo T520 with two graphics cards, an nVidia quadro and an intel graphics card. I'm running a Ubuntu and Windows 7 dual boot. I can no longer find any trace of my intel graphics card. In my linux boot: > lspci | grep VGA > 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) In Windows in control panel display- advanced settings, I only see the NVIDIA Quadro 2000M. In the BIOS there is no mention of the intel graphics card, no where I can find to try and turn it on or off. I thought I was going crazy, but then I found a post I made on ask ubuntu I made 3 months ago where I listed the output of lspci on this same machine: lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) What is going on? How could my intel graphics card have been disabled or turned off somehow without my knowledge? I've been in the BIOS 3 times now, each time convinced the last time I must have missed something, but I always find nothing. Am I missing something there? Could a thief have opened my computer and stolen my graphics card?

  Read the article

• How to get http requests details in a tcpdump?

  - by tucson

  I am trying to get a tcpdump trace of some http requests. Here is what I got so far (I replaced the real IP addresses with REMOTE and LOCAL): C:\>Windump -na -i 3 ip host REMOTE and ip src LOCAL and tcp port 80 Windump: listening on \Device\NPF_{8056BE5E-BDBB-44E6-B492-9274B410AD66} 13:13:34.985460 IP LOCAL.4261 > REMOTE.80: . 1784894764:1784894765(1) ack 1268208398 win 65535 13:13:38.589175 IP LOCAL.4302 > REMOTE.80: F 3708464308:3708464308(0) ack 982485614 win 65535 13:13:38.589285 IP LOCAL.4303 > REMOTE.80: F 890175362:890175362(0) ack 2462862919 win 65535 13:13:38.589330 IP LOCAL.4304 > REMOTE.80: F 1838079178:1838079178(0) ack 156173959 win 65535 13:13:38.589374 IP LOCAL.4305 > REMOTE.80: F 3952718843:3952718843(0) ack 2209231545 win 65535 13:13:38.589413 IP LOCAL.4306 > REMOTE.80: F 446105750:446105750(0) ack 3141849979 win 65535 13:13:38.590265 IP LOCAL.4302 > REMOTE.80: . ack 2 win 65535 13:13:38.590403 IP LOCAL.4304 > REMOTE.80: . ack 2 win 65535 13:13:38.590429 IP LOCAL.4303 > REMOTE.80: . ack 2 win 65535 13:13:38.590484 IP LOCAL.4305 > REMOTE.80: . ack 2 win 65535 13:13:38.590514 IP LOCAL.4306 > REMOTE.80: . ack 2 win 65535 But I do not get the following level of details: Request URL:http://domain.com/index.php Request Method:POST Status Code:200 OK POST /index.php HTTP/1.1 Host: domain.com Connection: keep-alive Content-Length: 151 Cache-Control: max-age=0 etc How can I get this level of data?

  Read the article

• sys.dm_exec_query_stats interaction with recompilation

  - by Sam Saffron

  We use sys.dm_exec_query_stats to track down slow queries and queries that are IO offenders. This works great, we get a lot of very insightful stats. It is clear this is not as accurate as running a profiler trace, as you have no idea when SQL Server will decide to chuck out a an execution plan. We have quite a few queries where the wrong execution plan is cached. For example queries like the following: SELECT TOP 30 a.Id FROM Posts a JOIN Posts q ON q.Id = a.ParentId JOIN PostTags pt ON q.Id = pt.PostId WHERE a.PostTypeId = 2 AND a.DeletionDate IS NULL AND a.CommunityOwnedDate IS NULL AND a.CreationDate @date AND LEN(a.Body) 300 AND pt.Tag = @tag AND a.Score 0 ORDER BY a.Score DESC The problem is that the ideal plan really depends on the date selected (screenshot of ideal plan): However if the wrong plan is cached, it totally chokes when the date range is big: (notice the big fat lines) To overcome this we were recommended to use either OPTION (OPTIMIZE FOR UNKNOWN) or OPTION (RECOMPILE) OPTIMIZE FOR UNKNOWN results in a slightly better plan, which is far from optimal. Executions are tracked in sys.dm_exec_query_stats. RECOMPILE results in the best plan being chosen, however no execution counts and stats are tracked in sys.dm_exec_query_stats. Is there another DMV we could use to track stats on queries with OPTION (RECOMPILE)? Is this behavior by-design? Is there another way we can for recompilation while keeping stats tracked in sys.dm_exec_query_stats? Note: the framework will always execute parameterized queries using sp_executesql

  Read the article

• Finding the current user authenticated by basic auth (Apache)

  - by jtd

  When you log in through a basic auth page, is the username you authenticated as stored anywhere (on the server or client machine), maybe in an environment variable? Background: I have a common web administration page for an e-mail server and I'd like to know who is doing what. When a user successfully logs in via basic auth, I somehow want to be able to identify them and log their actions. So each time a request is submitted, I can write to a log file. The basic format would be: $username ran a $function against $useraccount so if a user changed someone's permissions, eg: Admin-Bob ran a permission change against User-Scott So if errors occur, I can easily trace back in the log file what actions lead to the cause. I tried checking the %ENV hash to no avail, any Ideas? I don't really want to get into PHP-like sessions, because that would mean scrapping my basic auth, which gives me a fine degree of control already. If I have to code something with sessions, I'd need to implement a system to block users after maximum tries and so on, which I don't really want to code. I think this is better geared towards serverfault because it pertains to Apache moreso than the programming language. Sessions can be done in a myriad of languages.

  Read the article

• Vmware Workstation, Win7 host, Ubuntu guests with Nat + Host-only networks but they cannot connect to the Internet

  - by Ikon

  I have a Win7 host machine with Vmware Workstation. In the workstation I have 3 Ubuntu installed. All 3 Ubuntu guests have a Nat network - to access the internet without asking the router for a local address - and a Host-only network - to connect all Ubuntu quests and the host in a private network for internal communication, without touching the router. When I try to make any of the Ubuntu quests to get data from the internet - assuming that they would figure out that the Nat-ed interface can access the requested data - they fail and report that there is no route to my query. If I disconnect the 2nd interface on the Ubuntu guests with the Host-only network and restart networking, they start to know the route to the internet. Odd, during the installation of the guests they asked which of the 2 given interfaces - with Nat and Host-only config - should be used to get updates during installation and they oddly managed to get the updates. Not so after the installation has finished and rebooted. I have checked the Virtual Network Editor that the Nat interface should use my real network card to access the net, so there should be no problem. I wish not to use the router's dhcp service to give the Ubuntu quests an address, and also I don't want the guests to be accessable from the local network directly, but only by the host - that's the Host-only network is for. Any suggestions? Edit: 192.168.189.0 is the Nat interface and 192.168.7.0 is the Host-only. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.7.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.189.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.189.2 0.0.0.0 UG 100 0 0 eth0

  Read the article

• Running batch file through a service.

  - by wallz

  I'm trying to schedule a batch file to run through a third party application, however the output file doesn't get created in the directory. If I run the .BAT file from the command line, it works and the file gets created. Also using the Windows Schedule will also succeed. Basically, the 3rd party software will schedule the .BAT file and it shows success within the 3rd party user interface. The difference between running from the command prompt and the software, is that the software will use its Windows service to launch the batch. The 3rd party software will show success since it was able to successfully call the .BAT file to run, however it has no control of the other EXE's that's being called within the script. I'm able to run a simple .BAT file in the 3rd party software, for example a copy command. The .BAT I'm having problems with calls a compiled EXE which launches Excel to create a file to a location. The .bat file calls something.exe, which then calls Excel.exe: C:\something.exe -o D:\filename.xlsm C:\filename.xlsm refresh_pivot Do you think it's a permissions issue? I used Process Monitor to verify any Access Denied errors but everything seems to be working according to the trace. It worked on a non-64-bit OS, I'm currently using Win2008 64-bit.

  Read the article

• How to set a static route for an external IP address

  - by HorusKol

  Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

  Read the article

• Almost All Xenserver Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top. edit2 Output of vgcfgrestore, but from the rescue system, as there is no root to chroot to. # vgcfgrestore --list VG_XenStorage-x-b4b0-x-x-408b91acdcae File: /etc/lvm/archive/VG_XenStorage-x-x-x-x-408b91acdcae_00000.vg VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *before* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013 File: /etc/lvm/backup/VG_XenStorage-x-x-x-x-408b91acdcae VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *after* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013

  Read the article

• Fortigate restrict traffic through one external IP

  - by Tom O'Connor

  I've got a fortigate 400A at a client's site. They've got a /26 from British Telecom, and we're using 4 of those IPs as a NAT Pool. Is there a way to say that traffic from 172.18.4.40-45 can only ever come out of (and hence go back into) x.x.x.140 as the external IP? We're having some problems with SIP which looks like it's coming out of one, and trying to go back into another. I tried enabling asymmetric routing, didn't work. I tried setting a VIP, but even when I did that, it didn't appear to do anything. Any ideas? I can probably post some firewall snippets if need be.. Tell me what you want to see. SIP ALG config system settings set sip-helper disable set sip-nat-trace disable set sip-tcp-port 5061 set sip-udp-port 5061 set multicast-forward enable end Interesting Sidenote VoIP phones, with no special configuration can register fine to proxy.sipgate.co.uk, which has an IP address of 217.10.79.16. Which is cool. Two phones are using a different provider, whose proxy IP address is 178.255.x.x. These phones can register for outbound, but inbound INVITEs never make it to the phone. Is it possible that the Fortigate is having trouble with 178.255.x.x as it's got a 255 in it? Or am I just imagining things?

  Read the article

• What can I do to determine the root cause of a Windows server hanging/freezing?

  - by Aaronaught

  We set up a new server here a few weeks ago that I am informally responsible for managing. Almost everything works perfectly except for one thing: Every so often it hangs without warning. To clarify: When I say hangs, I mean completely. None of the services respond and I'm unable to even get onto a local console - the display acts as though there's no VGA signal. One time, the server actually responded to pings, another time I got the "destination host unreachable" response, but most of the time the pings just time out, as one would expect for a hung server. Event logs don't show anything after a reboot. I don't mean that they don't show anything interesting, I mean that they don't show anything at all from before the failure occurs to after the reboot. And there are never any performance problems, strange errors, or other obvious signs of impending doom before it happens. I don't expect any easy answers here. What I'd like to know his I can methodically determine the root cause of this problem, be it a misbehaving service, defective hardware, or something else. Is there any kind of logging I can set up that will help me get to the bottom of this? Any hardware diagnostics or remote monitoring? Anything else I can do to help me discover what's actually happening, or at least be able to eliminate what isn't wrong? Just to reiterate, I really don't want to start speculating about possible causes and take a trial-and-error approach, because it's going to be at least several days at a time before I would have conclusive results. I'm looking for solutions to reliably trace the problem to its source.

  Read the article

• Connecting to Server 2008 shares fails

  - by Chris J

  I'm having problems getting a reliable share working on an x64 Server 2008 R1 SP1 server. All works well after a reboot, but after some time (within a day) the shares become unavailable to XP and Server 2003 servers. Interestingly, they remain available to other Server 2008 servers. On trying to access \\server\share, Server 2003 returns immediately and simply gives me the message "The specified network name is no longer available", XP takes a minute or two to timeout before giving the same message. There doesn't seem to be anything in the event logs indicating a problem. Doing some googling over the last day or two I've seen the following blamed: Bad network drivers ... I've updated to the latest drivers with no result Symantec anti-virus ... we're not using it (currently no AV on the server) Receive window auto-tuning ... I've disabled with netsh int tcp set global autotuninglevel=disabled and netsh int tcp set global rss=disabled None of these have had an effect. Windows Firewall is currently disabled. As other Server 2008 boxes (both x32 and x64) can connect, I can only assume that there's some new security configuration that's not quite right - or there's an AD issue that I need to trace, but don't know where to start. Even if anyone doesn't know how to resolve, if someone knows what I need to look for with Wireshark this would be a help.

  Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >