Search Results

Search found 3634 results on 146 pages for 'volumetric light'.

Page 127/146 | < Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >

• Expectations for NTFS file recovery

  - by Fred Hamilton

  Yesterday I booted my XP system, and as I looked up a minute later I saw the light blue screen and tail-end of that pre-boot diskcheck Windows sometimes does if it finds an error (or was previously told to run a diskcheck drung the next boot). I didn't worry about it at the moment... But then I looked at my "scratch" disk, which was a 70% full, 750GB hard disk...and it now looks like it has been freshly formatted. It doesn't have a single file on it, just the hidden "System Volume Information" file and 750GB of freedom from data. I looked at some of the recovery tools from the Free NTFS partition recovery question and decided to try PC INSPECTOR™ File Recovery 4.x initially. It ran overnight and afterwards returned a list of thousands of files it could recover. The odd thing was that the filenames were lost, but the file extensions were not (WTF?). And all of the files were exactly 1,472kB in size. I recovered a dozen PDFs as a test, and 80% of them displayed OK despite being padded out to 1.5MB (though I assume any files 1472kB are hosed). My primary question is: Is this the best I can expect from any file recovery software when trying to recover NTFS files? Or is there perhaps something better out there? I assume this is as good as it gets, but wanted to check in with the experts first. Bonus questions: What might have happened to my drive? I didn't intentionally format it. I've never seen a disk error cause the drive to suddenly become a clean, reformatted drive. Could some malicious/confused software have told my PC to format my disk on reboot? Is that even a function Windows XP has? Why can the file extensions be recovered but not the filename? Does NTFS really treat them as separate entities? I thought I had 8.3 naming turned off, but maybe that had something to do with it. Or maybe it looks at the data in the file and guesses the extension?

  Read the article

• Computer experiencing slowdowns and lockups despite low cpu useage

  - by user157145

  my setup i5-2300 nvidia gtx 550 ti 6 gigs ram 600 w ocz modular psu recently reformatted and already experiencing drastic slowdown as soon as windows comes up, including repeated lockups with multiple various programs reporting that they are not responsive, then recovering after 10-30 seconds. ive checked memory and hard drive both of which come out fine. despite my plethura of worthless antiviral software im forced to assume that my illicit downloading practices have lead me into some comp trouble that i cant seem to determine. i have used ccleaner, search and destroy and malware bytes, all of which have found nothing to indicate what is causing this massive slowdown. in addition according to my resource manager my computer is operating at a load of only 30-50 percent CPU useage and 60 ram useage but taking 5-10 seconds to load files and open folders, and repeated lockups of multiple programs, especially firefox which seems to go unresponsive every 2-3 minutes. any help would be appreciated, i used a program called OTL by old timer, but cant make any sense of the results i was given. any help or suggestions would be appreciated, thank you for taking the time to read this i have avast but it didnt even find anything when i had it do a full system scan, so im thinking its clueless(also nortons, avg, and ad-aware). i also have mse but it has yet to complete a full scan it takes so long (i left it on last night but when i woke up my computer had a problem and had to restart). my hard drive has 300 gigs out of 1tb open and i already used hd tune pro, which said my harddrive was fine and its not a ssd. also im a noob at comps and only have the hd that is currently inside the computer in addition im not sure if studdering is the issue im suffering. my problem is that during my typing of these responses firefox has gone "not responsive" at least 5 times, each for times of about 5-10 seconds. when i try to control alt delete to bring up windows task manager it took 20 seconds. essentially its that my computer goes super slow at bringing up anything, or taking any action whatsoever that opens a program or file and has repeated incidents where i cant even click on whatever im trying to do because it locks up. the confusing thing about these incidents is that its right after restarting where there are minimal programs running and the computer and memory load is light.

  Read the article

• Good maintained privacy Add-On/settings set that takes usability into account?

  - by Foo Bar

  For some weeks I've been trying to find a good set of Firefox Addons that give me a good portion of privacy/security without losing to much of usability. But I can't seem to find a nice combination of add-ons/settings that I'm happy with. Here's what I tried, together with the pros and cons that I discovered: HTTPS Everywhere: Has only pro's: just install and be happy (no interaction needed), loads known pages SLL-encrypted, is updated fairly often NoScript - Fine, but needs a lot of fine-tuning, often maintained, mainly blocks all non-HTML/CSS Content, but the author sometimes seems to do "untrustworthy" decission RequestPolicy - seems dead (last activity 6 months ago, has some annoying bugs, official support mail address is dead), but the purpose of this is really great: gives you full control over cross-site requests: blocks by default, let's you add sites to a whitelist, once this is done it works interaction-less in the background AdBlock Edge: blocks specific cross-site requests from a pre-defined whitelist (can never be fully sure, need to trust others) Disconnect: like AdBlock Edge, just looking different, has no interaction possibilities (can never be fully sure, need to trust others, can not interact even if I wanted to) Firefox own Cookie Managment (block by default, whitelist specific sites), after building own whitelist it does it's work in the background and I have full control All These addons together basically block everything unsecure. But there are a lot of redundancies: NoScript has a mixed-content blocker, but FF has it's own for a while now. Also the Cookie blocker from NoScript is reduntant to my FF-Cookie setting. NoScript also has an XSS-blocker, which is redundant to RequestPolicy. Disconnect and AdBlock are extremly redundant, but not fully. And there are some bugs (especially RequestPolicy). And RequestPolicy seems to be dead. All in all, this list is great but has these heavy drawbacks. My favourite set would be "NoScript Light" (only script blocking, without all the additonal redundant-to-other-addons hick-hack it does) + HTTPS Everywhere + RequestPolicy-clone (maintained, less buggy), because RequestPolicy makes all other "site-blockers" obsolete (because it blocks everything by default and let's me create a whitelist). But since RequestPolicy is buggy and seems to be dead I have to fallback to AdBlock Edge and Disconnect, which don't block all and and need more maintaining (whitelist updates, trust-check). Are there addons that fulfill my wishes?

  Read the article

• Laptop turning off when fan is spinning hard

  - by Ieyasu Sawada

  My laptop seems to have reach its lifespan. Its an Acer laptop so I guess that's normal. But I'd like to hear your opinions about this. My laptop is only 2 years old. I haven't heard the fan spinning like crazy not until these past 5 months. What I did: Hoping that its just the applications that I have installed that's consume the life of my laptop from the background. I used PC Decrapifier to uninstall some of the things that I don't need. Reformatted my computer but only the primary partition since my files are on the second partition. Bought a cooling pad. None of these works. I noticed the fan spins so hard when: I have a lot of browser tabs open. Full screen mode a flash video that I'm viewing online. Using VLC to watch encoded videos. There's this thing called minicoder http://sourceforge.net/projects/minicoder/ to reduce the size of videos without affecting much of the quality. I'm suspecting that it needs additional software(to make life easier for the hardware) even though the video is working fine in VLC. VLC consumes about 300,000K and above(as seen from task manager) while watching videos (.mkv). The problem: Laptop suddenly turns off when the fan spins like crazy for about 20 minutes. I'm always checking to see if its already too hot(using my fingers to feel the side of the laptop) but its not so I continued watching and then poof! computer turns off. Laptop won't turn on immediately when I turn it on after it turning off by itself. The light for the power goes on but its turns off immediately. I have to wait for about 10-20 seconds before it boots up without problems. So how do I go about this? Is this just normal for Acer laptops after about 2 years of heavy usage (8-12 hours a day)? My usage is heavy but I normally only have a text-editor(sublime) and browser open(chrome). Here's what I got from HW monitor:

  Read the article

• Scientific Linux - mysql and apache fail to start on reboot

  - by Derek Deed

  Both mysqld and httpd fail to restart following a reboot of the server, although chkconfig --list shows both daemons set to on for run levels 2,3,4 & 5 All control is being exectuted via Webmin Reboot server – MySQl and Apache not running MySQL Database Server MySQL version 5.1.69 MySQL is not running on your system - database list could not be retrieved. ________________________________________ Click this button to start the MySQL database server on your system with the command /etc/rc.d/init.d/mysqld start. This Webmin module cannot administer the database until it is started. Apache Webserver Apache version 2.2.15 Start Apache Search Docs.. Global configuration Existing virtual hosts Create virtual host Select all. | Invert selection. Default Server Defines the default settings for all other virtual servers, and processes any unhandled requests. Address Any Port Any Server Name Automatic Document Root /var/www/drupal Virtual Server Processes all requests on port 443 not handled by other virtual servers. Address Any Port 443 Server Name Automatic Document Root /var/www/drupal Select all. | Invert selection. chkconfig --list mysqld mysqld 0:off 1:off 2:on 3:on 4:on 5:on 6:off chkconfig --list httpd httpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off Manually Restart Apache chkconfig --list httpd httpd 0:off 1:off 2:on 3:on 4:on 5:on 6:off Manually Restart MySQL chkconfig --list mysqld mysqld 0:off 1:off 2:on 3:on 4:on 5:on 6:off Everything now running okay; but no difference in the chkconfig outputs above. I tried: chkconfig --levels 235 httpd on /etc/init.d/httpd start and the same for mysqld but no change in operation. Log files show that the shutdown has been completed successfully; but there is no indication of the service restarting until it is executed manually: 131112 13:59:15 InnoDB: Starting shutdown... 131112 13:59:16 InnoDB: Shutdown completed; log sequence number 0 881747021 131112 13:59:16 [Note] /usr/libexec/mysqld: Shutdown complete 131112 13:59:16 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended 131112 14:09:52 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql 131112 14:09:52 InnoDB: Initializing buffer pool, size = 8.0M 131112 14:09:52 InnoDB: Completed initialization of buffer pool And the Apache logs: [Tue Nov 12 13:59:13 2013] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Tue Nov 12 13:59:13 2013] [notice] Digest: generating secret for digest authentication ... [Tue Nov 12 13:59:13 2013] [notice] Digest: done [Tue Nov 12 13:59:14 2013] [notice] Apache/2.2.15 (Unix) DAV/2 PHP/5.3.3 mod_ssl/2.2.15 OpenSSL/1.0.0-fips configured -- resuming normal operations [Tue Nov 12 13:59:14 2013] [notice] caught SIGTERM, shutting down [Tue Nov 12 14:27:13 2013] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) [Tue Nov 12 14:27:13 2013] [notice] Digest: generating secret for digest authentication ... [Tue Nov 12 14:27:13 2013] [notice] Digest: done [Tue Nov 12 14:27:13 2013] [notice] Apache/2.2.15 (Unix) DAV/2 PHP/5.3.3 mod_ssl/2.2.15 OpenSSL/1.0.0-fips configured -- resuming normal operations Is anyone able to shed any light on this problem?

  Read the article

• How to start nginx via different port(other than 80)

  - by Zhao Peng

  Hi I am a newbie on nginx, I tried to set it up on my server(running Ubuntu 4), which already has apache running. So after I apt-get install it, I tried to start nginx. Then I get the message like this: Starting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) That makes sense as Apache is using port 80. Then I tried to modify nginx.conf, I reference some articles, so I changed it like so: server { listen 8080; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } After saving this and try to start nginx again, I still get the same error as previously. I cannot really find a related post about this, could any good people shred some light? Thanks in advance :) ========================================================================= I should post all the content in conf here: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; server { listen 81; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:81; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } } } mail { See sample authentication script at: http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript auth_http localhost/auth.php; pop3_capabilities "TOP" "USER"; imap_capabilities "IMAP4rev1" "UIDPLUS"; server { listen localhost:110; protocol pop3; proxy on; } server { listen localhost:143; protocol imap; proxy on; } } Basically, I changed nothing except adding the server part.

  Read the article

• UPS vs Solar Power in case of power failure for a server [on hold]

  - by Zen 8000k

  I am looking for a low power, low end pc able to run 24/7 without overheating and a way to support it in case of power failure. Power failures can be up to 72 hours. The pc dosen't need a monitor or keyboard. A modem must also be protected in case of power failure. When i say low end, i don't mean crap. The cpu needs to be x86 and have at least 1k cpu in this chart: http://www.cpubenchmark.net/index.php What's the best way to do this? EDIT: more info. I need to run a home server. The server will perform light tasks mainly. A x86 cpu sadly is the only route for my use. I want to be able to run the server and the router/modem in case of power failure. Now, regarding how long the power will fail: 1) 1 hours is OK for most situations. (say 90%) 2) 3 hours is OK (say 98%) 3) 6 hours is more thank OK. (say 99.5%) 4) On extreme cases the power might fail days. I believe this is very unlikely to happen. More is great but, really, how ofter power will fail more than 3 hours? I believe once every year at best. Well, that's too rare to care about. Given the above, I am looking for a cost effective way to archive 1-3 hour power or 6 hour if possible. Solutions: You guys give me great ideas. 1) Power generator: no good as power will fail for 10 seconds before returning. Also I read online, "clean" power generators cost 1.5k+, so it's out of budged. Non clean generator might damage electronics, right? 2) Solar power: i don't know for sure about this. Sounds like a great idea, too good to be true, honestly. For only 200$ i get 100+w? What are the drawbacks here? 3) UPS: This seems to be the best. The only problem is the cost. Cost < 200$ = great 400$ = budged limit

  Read the article

• Local Apache on Windows XP not finishing page requests

  - by asgeo1

  I have Apache 2.2.11 installed locally on my Windows XP (SP3) dev machine, which I setup about 3 months ago. I have just started having a strange problem in the last few week. Apache is serving some basic PHP applications like phpMyAdmin. When I make a page request, Apache appears to not finish serving all resources for that page. Firefox shows the "Transferring data from servername..." message, and the page never completes. The same problem happens in Internet Explorer too. I can sometimes tell which resource it is waiting on, because most of the page will render except for some image or similar resources. (Not sure why Firebug doesn't show this) It doesn't have the problem every page request - for page requests where most of the resources are cached in my browser, the page request will work with no problems. Or pages that are very light will work with no problems. However, if I "hard" refresh the page, I will have this problem (probably because it is requesting all page resources) Does anyone know what this could be? It is so strange that it has only just started happening - and I did not make any changes to my system (that I am aware of) I tried playing with the Apache ThreadsPerChild setting, but it did not seem to make a difference. UPDATE: I have been doing some more tests. I have been serving the most basic of pages, just a plain HTML file: <html> <body> <h1>testing</h1> </body> </html> If I request this page multiple times in a row, AND each request occurs immediately after the previous has completed, then 50% of the time the request will time out. However, if I put a 1-2 second gap between requests, then there is no problem. This correlates to what I have observed when the brower requests a real application page. When the browser has nothing cached, then all of the page resources are requested from the browser in a short amount of time - this appears to trigger the problem. UPDATE2: Nathan Long has helped me understand the issue a little better with the server-status page (see below). It is weird, it is like the server has a hickup sending data to the client. The client sits there waiting forever for data that never arrives. Closing the client process does not terminate the connection on the server - the server still has active threads for each previously attempted connection, but they just sit there - not sending any data and never terminating. (even though the client is now closed) Only a restart of the server seems to terminate them.

  Read the article

• Event ID 17890 (A significant part... paged out.) with SQL Server 2008

  - by Godeke

  I have a machine that has SQL Server 2008 Standard installed. Periodically (about once an hour) I am getting Event ID 17890 several times in a row. An example: 6:28:54 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 0 seconds. Working set (KB): 10652, committed (KB): 628428, memory utilization: 1%%. 6:34:27 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 332 seconds. Working set (KB): 169780, committed (KB): 546124, memory utilization: 31%%." 6:38:55 "A significant part of sql server process memory has been paged out. This may result in a performance degradation. Duration: 600 seconds. Working set (KB): 245068, committed (KB): 546124, memory utilization: 44%%." This pattern repeated at 7:26 - 7:37, 8:26 - 8:36, 9:24 - 9:35 and so with the same increasing working set and memory utilization pattern. I don't have any (known) background tasks running at this time. Backups run at 2:00 This subsided from 11:00 at night until it resumed at 4:00 in the morning and has been continuing the intermittent 10 minute glitch periods. As this server has plenty of RAM (the commit charge has peaked at 2,871,564 of 4,194,012 physical) I disabled the paging files after reading several items I dug up searching Google and not finding any of them changing the situation. This pattern I am documented is after removing the paging files, so I'm not even sure where we are paging the SQL process could be going. I also changed the SQL process memory to have a minimum of 500MB and a maximum of 2GB of RAM (as this is a light duty database server serving only a small workgroup). Has anyone encountered this? Prior to disabling the page files this error would cause 5 minutes of disk thrashing that disabled access to the databases, files, IIS webs and so on. Since disabling the page files it just logs strange things, but I'm not seeing a performance drop at least. Any suggestions would be welcome.

  Read the article

• Poor performance of single processor 32bit Windows XP xompared SMP in VBA+Excel

  - by Adam Ryczkowski

  Welcome! On many computers I experienced poor performance of 32 bit guests running on 64 bit Linux host (I used only the Debian family). At last I managed to collect benchmark data. I made the benchmark by running custom VBA macro, (which we use in our company) that generates 284 pages long Word document full of Excel Pie charts, tables and comments. The macro is run as a single task (excluding the standard services) on a set of identically configured Windows XP 32-bit systems. I measured the time (in sec.) needed to perform the test. The computer (i.e. my notebook Asus P53E) supports both VT-d extensions and native Windows XP. It has 2-core processor, each core is hyperthreaded, so in total we have 4 mostly independent execution units. I use the latest VirtualBox 4.2 and VMWare Workstation 9.0 for Linux, installed together on the same host (running Mint 13 Maya) but never run simultaneously. The results (in column Time) are no less accurate than ± 10% Here are the results (sorry for the format, but I couldn't find out a better solution for tables in SO): +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ | Host software | # processor | Windows kernel | IO APIC | VT-x/AMD-V | 2D Video Accel | Time | +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 1 | 0 | 1139 | | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 1 | 1 | 1050 | | VirtualBox | 1 | Advanced Configuration and Power Interface (ACPI) PC | 0 | 0 | 1 | 1644 | | VirtualBox | 4 | ACPI Multiprocessor PC | 1 | 1 | 1 | 6809 | | VMWare | 1 | ACPI Uniprocessor PC | | 1 | 1 | 1175 | | VMWare | 4 | ACPI Multiprocessor PC | | 1 | 1 | 3412 | | Native | 4 | ACPI Multiprocessor PC | | | | 1693 | | Native | 1 | Advanced Configuration and Power Interface (ACPI) PC | | | | 1170 | +---------------+-------------+------------------------------------------------------+---------+------------+----------------+------+ Here are the striking conclusions: Although I've read in the VirtualBox fora about abysmal performance with 32-bit guest on 64-bit host, VMWare also has problems compared to native run, still being twice faster(!) than VBox. Although VBA is inherently single-threaded, the Excel calculations, which take much more than a half of total computation time, supposedly aren't. So one would expect some speed gain when running on 2+ cores ("+" for hyperthreading). What we see is a speed loss. And quite big one too. For the VirtualBox the VT-d extension isn't a big deal. Can anyone shed some light on why the singlethreaded Windows kernel is so much faster than the SMP one?

  Read the article

• How can I change how OS X's 'say' command pronounces a word?

  - by jwhitlock

  OS X's say command is useful for some tasks (such as Skype's 'notify me when a contact comes online), but it is pronouncing some names incorrectly. Is there a way to teach say to pronounce a word differently? For example, try: say "Hi, Joel Spolsky" The 'ol' sounds like 'ball' rather than 'old'. I'd like to add an exception that say "Pronounce Spolsky like this", rather than try to teach new linguistic rules. I bet there is a way since it can pronounce "iphone" as Apple wants. Update - After some research, here's what I've learned: Text-to-speech is split between turning the text to phonemes, and then the phonemes are turned into audio using a voice. Changing the voice doesn't effect the phonemes. The Speech Synthesis Manager has some functions for turning text to phonemes, and a method for registering a speech dictionary that will add new text-phoneme maps. However, Apple's speech dictionary must be in a binary form - I didn't find any plist XML. Using dtrace while running say, I found some interesting files opened in /System/Library/PrivateFrameworks/SpeechDictionary.framework/Resources. This is probably the speech dictionary, but they are all binary, except for Homophones, which is XML. Adding entries to Homophones does nothing - it is probably used in speech-to-text. They are also code signed by Apple - changing them may prevent some programs from working. PrefixDictionary CartNames CartLite SymbolDictionary Homophones There are ways to add text versions of application interface elements so VoiceOver works, a lot of which a developer gets for free, but there are tricky bits. The standard here appears to be to use a phonetic spelling as needed. My guesses are: say is a light layer of code on top of the Speech Synthesis Manager. It would be easy for the Apple devs to add a command line option to take the path to a speech dictionary plist for alternate phoneme mapping, but they didn't. It may be a useful open-source project to write a better say. Skype probably uses Speech Synthesis Manager directly, leaving no hooks to change the way my friend's names are pronounced, other than spelling them phonetically, which is silly. The easiest way to make a command line version of say is how JRobert suggested. Here's my quick implementation, using Doug Harris's spelling suggestion: #!/bin/sh echo $@ | tr '[A-Z]' '[a-z]' | sed "s/spolsky/spowlsky/g" | /usr/bin/say Finally, some fun command line stuff: # Apple is weird sqlite3 /System/Library/PrivateFrameworks/SpeechDictionary.framework/Resources/Tuples .dump # Get too much information about what files are being opened sudo dtrace -n 'syscall::open*:entry { printf("%s %s",execname,copyinstr(arg0)); }' # Just fun say -v bad "Joel Spolsky Spolsky Spolsky Spolsky Spolsky, Joel Spolsky Spolsky Spolsky Spolsky Spolsky" echo "scale=1000; 4*a(1)" | bc -l | say

  Read the article

• How to enjoy DVD on Apple iPad

  - by user44251

  I believe many people spent a sleepless night yesterday waiting for the new Apple Tablet to come, just a few days ago or perhaps longer I noticed fierce debate about it, its name, size, capacity, processor, main features, price etc. And now, they can take a long breath with the new Apple Tablet named iPad officially released on 28, January, 2010 (Beijing Time). But I know a new battle just begins. iPad, sounds somewhat like iPod and it really shares some similarities in terms of shape like smart, light and portable. It has a 9.7-inch, LED-backlit, IPS display with a remarkable precise Multi-Touch screen. And yet, at just 1.5 lbs and 0.5 inches thin, it's easy to carry and use everywhere. It can greatly facilitates your experience with the web, emails, photos and videos. Right now, it can run almost 140.000 of the apps on the Apple store. It can even run the apps you have downloaded for your iPhone or iPod touch. But so far, I haven't seen any possibility that it can work with DVD, probability there is no built-in DVD-ROM or DVD player which can play DVD directly. As Apple iPad states, the video formats supported are MPEG-4 (MP4, M4V), H.264, MOV etc and audio formats accepted are AAC, Proteceted AAC, MP3, AIFF and WAV etc, those are formats that are commonly used with iMac. This could really a hard nut to crack if you want to watch your favourite DVD on this magic Apple iPad. But don't worry, there is still way out, you just need a few steps for ripping and importing DVD movies to Apple iPad with a simple application DVD to iPad converter What's on DVD to iPad Converter for Mac DVD to iPad converter for Mac is a powerful and professional application designed for the newly released Apple iPad which can rip, convert your DVD contents to Apple iPad compatible MPEG-4 (MP4, M4V), H.264, MOV etc, and other popular file formats like AVI, WMV, MPG, MKV, VOB, 3GP, FLV etc can also be converted so that you can put on your portable devices like iPod, iPhone, iRiver, BlackBerry etc. Besides, it can also extract audio from DVD videos and save as MP3, AIFF, AAC, WAV etc. Mac DVD to iPad converter has also been enhanced that can run both on PowerPC and Intel (Snow Leopard included). It can offer versatile editing features which allows you to make your own DVD videos. For example, you can cut your DVD to whatever length you like by Trim, crop off unwanted parts from DVD clips by Crop, add special effect like Gray, Emboss and Old film to make your videos more artistic. Besides, its built-in merging feature and batch mode allows you to join several DVD clips into a single one and do batch conversion. And more features can be expected if you afford a few minutes to try.

  Read the article

• Windows 7 Home hangs at "Welcome" screen

  - by White Phoenix

  I'm asking on behalf of a friend who's currently having problems with his machine. Windows 7 Home 32-bit. He's too far away for me to help by going over to his house - I'm helping him over the Internet. This is his current machine: http://www.newegg.com/Product/Product.aspx?Item=N82E16883227134 The only two changes he made to that machine is to swap out the gfx card for a EVGA GTX 460 and the PSU for a Corsair TX650. Here's what happened: He was playing a computer game (fairly CPU/GPU intensive) and had some music going in the background in foobar while playing. Suddenly, he notices the music stopped playing, so he switches to foobar to try to close it, but it freezes up (window won't respond). So he figures it's just foobar having a bad day and force quits that program. Suddenly, his game won't respond, so he force quits that, then the entire computer just went to crap at that point, so he hits the restart button on his machine. Computer POSTS fine, but now he gets stuck at the Windows "welcome" screen (his account is set to auto-login). HD activity light is solid yellow but he doesn't hear HDD activity. He tried booting into Safe Mode - gets stuck at the "welcome screen". Tried a STartup Repair within Windows 7, it found a few problems, but still gets stuck at welcome. I advised him to boot off the DVD - sfc /scannow found nothing (couldn't use the regular /scannow option; says there's a repair pending, had to use use offbootdir/offwindir command switches). Ran startup repair 3 times - found nothing. My friend runs virus/malware scans on a regular basis, so he's fairly sure it's not that either. Right now I'm having my friend run chkdsk /R on the computer while in this Startup Recovery mode - so far it's caught a few bad sectors. However at this point I'm kinda wondering which way to go if chkdsk doesn't fix it. Quick Google search said someone had success by booting Windows with bootlogging on - some others have success with running the aforemented chkdsk, etc. The fact that Windows cannot even boot into Safe Mode concerns me. While we're waiting for chkdsk /R to finish, are there any other options I can give my friend short of reinstalling Windows 7? He has his data on a separate partition so that's not a major problem (though it'll be an annoyance for him). I suspect his hard drive may be having some issues, but my main concern is getting him back up and running before we start diagnosing the hard drive (I may have him run some sort of SMART test utility later).

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• Computer freezes +/- 30 seconds, suspicion on SSD

  - by Robert vE

  My computer freezes for about 30 seconds, this happens occasionally. When it happens I can still move the mouse, sometimes even alternate between tabs in google chrome. If I try to open windows explorer nothing happens. Also chrome rapports "waiting for cache". It also happens in starcraft II, during which the sounds loops. I have made a Trace as this topic describes: How do I troubleshoot a Windows 7 freeze or slowness? Trace: https://docs.google.com/open?id=0B_VkKdh535p6NklhSDdBLURUMnc I have looked at it, but I couldn't figure it out. My system specs are: AMD Athlon X4 651 Asus Ati HD6670 ADATA SSD sp900 Asus f1a55 mainboard 4 GB crucial 1333 ram 500 watt atx ps I'm running Windows 7, fully updated. Any help is much appreciated. Update: I tried something before your reply that may have helped the problem. I don't know for sure if it has, it's too soon to tell. A bit of history first. I had problems installing win7 on my ssd from the start. In IDE mode it worked, but I had the same problems as above. AHCI was a total fail, with it on before install as well as turning it on after install (including tweaking register). I didn't bother installing the AMD chipset/AHCI as it was reported to have no TRIM function and thus make problems worse. Eventually I did install the AMD SMbus driver as the stability issues were driving me crazy. It worked, no more issues, until I installed some extra drivers and software. Audio/LAN/ASUS suite, I don’t see the relation, but somehow it screwed up my system again. As a last effort I posted here on this site. After which the thought occurred to me turn on AHCI again as by now I had all necessary drivers installed anyway. (plus all windows updates downloaded/installed in the meantime) I did and stability didn’t seem great the first few reboots, but eventually everything seemed to work great. I tried to play starcraft II – an almost guaranteed freeze before – and I had no problems. I’m basically crossing my fingers and hope the problem is gone for good. I still think it has something to do with my SSD. In my research into the problem I noticed a lot of these issues with sandforce 2281 firmware, the exact same firmware I have. People reported the same problem that I had, freezes. Additionally they reported that during a freeze the hdd light stayed on, I noticed after I read this that this happened with my computer as well. None of this is conclusive evidence that my SSD is really to fault, but it is suspicious. And why turning on AHCI would fix it I don’t know. Thank you Tom for taking a look, if the problem returns I will certainly do what you advised.

  Read the article

• 40k Event Log Errors an hour Unknown Username or bad password

  - by ErocM

  I am getting about 200k of these an hour: An account failed to log on. Subject: Security ID: SYSTEM Account Name: TGSERVER$ Account Domain: WORKGROUP Logon ID: 0x3e7 Logon Type: 4 Account For Which Logon Failed: Security ID: NULL SID Account Name: administrator Account Domain: TGSERVER Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x334 Caller Process Name: C:\Windows\System32\svchost.exe Network Information: Workstation Name: TGSERVER Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: Advapi Authentication Package: Negotiate Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols. - Key length indicates the length of the generated session key. This will be 0 if no session key was requested. On my server... I changed my adminstrative username to something else and since then I've been inidated with these messages. I found on http://technet.microsoft.com/en-us/library/cc787567(v=WS.10).aspx that the 4 means "Batch logon type is used by batch servers, where processes may be executing on behalf of a user without their direct intervention." which really doesn't shed any light on it for me. I checked the services and they are all logging in as local system or network service. Nothing for administrator. Anyone have any idea how I tell where these are coming from? I would assume this is a program that is crapping out... Thanks in advance!

  Read the article

• Both nginx and php5-fpm init.d startup scripts are non-functional and returning no errors..? But they used to work perfectly

  - by Ollie Treend

  I have been using nginx and php5-fpm on my Ubuntu box for a while now. Everything has been configured and setup correctly, and it ran like a charm. I have been keeping the packages updated & upgraded as usual, but haven't touched the nginx OR php5-fpm config files at all (thus I'm pretty sure this isn't my fault... ) Basically, I noticed nginx wasn't running as it should be. I ran the command sudo service nginx start, and the script did nothing. The same thing happens when trying to do anything - start, stop, restart or reload. This also happens for the "php5-fpm" init script - although all other init scripts seem to be functioning correctly. When trying to start nginx OR php5-fpm, this is what happens: root@HAL:/etc# service php5-fpm start root@HAL:/etc# I can't understand what is going wrong. The script isn't returning errors, but similarly it isn't starting the daemon or reporting success as usual. For reference, both installations are from the official nginx and php5-fpm PPAs. The fact that both started doing this at the same time has thrown me - since they are both unrelated packages. I have since purged both sets of packages from my system with apt-get purge ... and also apt-get remove --purge ... both of which have successfully removed the packages, their config files, and their init.d startup scripts. After having reinstalled nginx, I now have a functioning startup script again - I can start the web server as usual. However, php5-fpm is still experiencing the strange premature exiting of the startup script.. and I really can't figure out what's causing it. I have no idea what caused this to occur initially, but have managed to fix nginx. I now need to fix the php5-fpm startup script. If anybody could shed some light on this situation, I would be very grateful! The chances are both these issues are related - and they were caused by me doing something stupid. But now I need to fix it. This time I was lucky - because these problems are just on my development server. But I have 2 other live servers which are configured in a similar way, and I am worried the same thing will happen to these two as well! Has anybody else come across this? Do you have any words of advice? Thank you

  Read the article

• Will spreading your servers load not just consume more recourses

  - by Saif Bechan

  I am running a heavy real-time updating website. The amount of recourses needed per user are quite high, ill give you an example. Setup Every visit The application is php/mysql so on every visit static and dynamic content is loaded. Recourses: apache,php,mysql Every second (no more than a second will just be too long) The website needs to be updated real-time so every second there is an ajax call thats updates the website. Recourses: jQuery,apache,php,mysql Avarage spending for single user (spending one minute and visited 3 pages) Apache: +/- 63 requests / responsess serving static and dynamic content (img,css,js,html) php: +/- 63 requests / responses mysql: +/- 63 requests / responses jquery: +/- 60 requests / responses Optimization I want to optimize this process, but I think that maybe it would be just the same in the end. Before implementing and testing (which will take weeks) I wanted to have some second opinions from you guys. Every visit I want to start off with having nginx in the front and work as a proxy to deliver the static content. Recources: Dynamic: apache,php,mysql Static: nginx This will spread the load on apache a lot. Every Second For the script that loads every second I want to set up Node.js server side javascript with nginx in te front. I want to set it up that jquery makes a request ones a minute, and node.js streams the data to the client every second. Recources: jQuery,nginx,node.js,mysql Avarage spending for single user (spending one minute and visited 3 pages) Nginx: 4 requests / responsess serving mostly static conetent(img,css,js) Apache: 3 requests only the pages php: 3 requests only the pages node.js: 1 request / 60 responses jquery: 1 request / 60 responses mysql: 63 requests / responses Optimization As you can see in the optimisation the load from Apache and PHP are lifted and places on nginx and node.js. These are known for there light footprint and good performance. But I am having my doubts, because there are still 2 programs extra loaded in the memory and they consume cpu. So it it better to have less programs that do the job, or more. Before I am going to spend a lot of time setting this up I would like to know if it will be worth the while.

  Read the article

• What happens to missed writes after a zpool clear?

  - by Kevin

  I am trying to understand ZFS' behaviour under a specific condition, but the documentation is not very explicit about this so I'm left guessing. Suppose we have a zpool with redundancy. Take the following sequence of events: A problem arises in the connection between device D and the server. This causes a large number of failures and ZFS therefore faults the device, putting the pool in degraded state. While the pool is in degraded state, the pool is mutated (data is written and/or changed.) The connectivity issue is physically repaired such that device D is reliable again. Knowing that most data on D is valid, and not wanting to stress the pool with a resilver needlessly, the admin instead runs zpool clear pool D. This is indicated by Oracle's documentation as the appropriate action where the fault was due to a transient problem that has been corrected. I've read that zpool clear only clears the error counter, and restores the device to online status. However, this is a bit troubling, because if that's all it does, it will leave the pool in an inconsistent state! This is because mutations in step 2 will not have been successfully written to D. Instead, D will reflect the state of the pool prior to the connectivity failure. This is of course not the normative state for a zpool and could lead to hard data loss upon failure of another device - however, the pool status will not reflect this issue! I would at least assume based on ZFS' robust integrity mechanisms that an attempt to read the mutated data from D would catch the mistakes and repair them. However, this raises two problems: Reads are not guaranteed to hit all mutations unless a scrub is done; and Once ZFS does hit the mutated data, it (I'm guessing) might fault the drive again because it would appear to ZFS to be corrupting data, since it doesn't remember the previous write failures. Theoretically, ZFS could circumvent this problem by keeping track of mutations that occur during a degraded state, and writing them back to D when it's cleared. For some reason I suspect that's not what happens, though. I'm hoping someone with intimate knowledge of ZFS can shed some light on this aspect.

  Read the article

• What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

  - by Tyler

  Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

  Read the article

• Choosing parts for a high-spec custom PC - feedback required [closed]

  - by James

  I'm looking to build a high-spec PC costing under ~£800 (bearing in mind I can get the CPU half price). This is my first time doing this so I have plenty of questions! I have been doing lots of research and this is what I have come up with: http://pcpartpicker.com/uk/p/j4lE Usage: I will be using it for Adobe CS6, rendering in 3DS Max, particle simulations in Realflow and for playing games like GTA IV (and V when it comes out), Crysis 1/2, Saints Row The Third, Deus Ex HR, etc. Questions: Can you see any obvious problem areas with the current setup? Will it be sufficient for the above usage? I won't be doing any overclocking initially. Is it worth buying the H60 liquid cooler, or will the fan that comes with the CPU be sufficient? Is water cooling generally quieter? Is the chosen motherboard good for the current components? And is it future-proof? I read that the HDD is often the bottleneck when it comes to gaming. I presume this is true to other high-end applications? If so, is my selection good? I keep changing my mind about the GPU; first the 560, now the 660. Can anyone shed some light on how to choose? I read mixed opinions about matching the GPU to the CPU. Will the 560 or the 660 be sufficient for my required usage? Atm I'm basing my choice on the PassMark benchmarks and how much they cost. The specs on the GeForce website state that the 560 and the 660 both require 450W. Is this a good figure to base the wattage of my PSU on? If so, how do you decide? Do I really need 750W? The latest GTX 690 requires 650W. Is it a good idea to buy a 750W PSU now to future-proof myself?

  Read the article

• AGENT: The World's Smartest Watch

  - by Rob Chartier

  AGENT: The World's Smartest Watch by Secret Labs + House of Horology Disclaimer: Most if not all of this content has been gleaned from the comments on the Kickstarter project page and comments section. Any discrepancies between this post and any documentation on agentwatches.com, kickstarter.com, etc.., those official sites take precedence. Overview The next generation smartwatch with brand-new technology. World-class developer tools, unparalleled battery life, Qi wireless charging. Kickstarter Page, Comments Funding period : May 21, 2013 - Jun 20, 2013 MSRP : $249 Other Urls http://www.agentwatches.com/ https://www.facebook.com/agentwatches http://twitter.com/agentwatches http://pinterest.com/agentwatches/ http://paper.li/robchartier/1371234640 Developer Story The first official launch of the preview SDK and emulator will happen on 20-Jun-2013.  All development will be done in Visual Studio 2012, using the .NET Micro Framework SDK 2.3.  The SDK will ship with the first round of the expected API for developers along with an emulator. With that said, there is no need to wait for the SDK.  You can download the tooling now and get started with Apps and Faces immediately.  The only thing that you will not be able to work with is the API; but for example, watch faces, you can start building the basic face rendering with the Bitmap graphics drawing in the .NET Micro Framework.   Does it look good? Before we dig into any more of the gory details, here are a few photos of the current available prototype models.   The watch on the tiny QI Charter   If you wander too far away from your phone, your watch will let you know with a vibration and a message, all but one button will dismiss the message.   An app showing the premium weather data!   Nice stitching on the straps, leather and silicon will be available, along with a few lengths to choose from (short, regular, long lengths). On to those gory details…. Hardware Specs Processor 120MHz ARM Cortex-M4 processor (ATSAM4SD32) with secondary AVR co-processor Flash & RAM 2MB of onboard flash and 160KB of RAM 1/4 of the onboard flash will be used by the OS The flash is permanent (non-volatile) storage. Bluetooth Bluetooth 4.0 BD/EDR + LE Bluetooth 4.0 is backwards compatible with Bluetooth 2.1, so classic Bluetooth functions (BD/EDR, SPP/AVRCP/PBAP/etc.) will work fine. Sensors 3D Accelerometer (Motion) ST LSM303DLHC Ambient Light Sensor Hardware power metering Vibration Motor (You can pulse it to create vibration patterns, not sure about the vibration strength - driven with PWM) No piezo/speaker or microphone. Other QI Wireless Charging, no NFC, no wall adapter included Custom LED Backlight No GPS in the watch. It uses the GPS in your phone. AGENT watch apps are deployed and debugged wirelessly from your PC via Bluetooth. RoHS, Pb-free Battery Expected to use a CR2430-sized rechargeable battery – replaceable (Mouser, Amazon) Estimated charging time from empty is 2 hours with provided charger 7 Days typical with Bluetooth on, 30 days with Bluetooth off (watch-face only mode) The battery should last at least 2 years, with 100s of charge cycles. Physical dimensions Roughly 38mm top-to-bottom on the front face 35mm left-to-right on the front face and around 12mm in depth 22mm strap Two ~1/16" hex screws to attach the watch pin The top watchcase material candidates are PVD stainless steel, brushed matte ceramic, and high-quality polycarbonate (TBD). The glass lens is mineral glass, Anti-glare glass lens Strap options Leather and silicon straps will be available Expected to have three sizes Display 1.28" Sharp Memory Display The display stays on 100% of the time. Dimensions: 128x128 pixels Buttons Custom "Pusher" buttons, they will not make noise like a mouse click, and are very durable. The top-left button activates the backlight; bottom-left changes apps; three buttons on the right are up/select/down and can be used for custom purposes by apps. Backup reset procedure is currently activated by holding the home/menu button and the top-right user button for about ten seconds Device Support Android 2.3 or newer iPhone 4S or newer Windows Phone 8 or newer Heart Rate monitors - Bluetooth SPP or Bluetooth LE (GATT) is what you'll want the heart monitor to support. Almost limitless Bluetooth device support! Internationalization & Localization Full UTF8 Support from the ground up. AGENT's user interface is in English. Your content (caller ID, music tracks, notifications) will be in your native language. We have a plan to cover most major character sets, with Latin characters pre-loaded on the watch. Simplified Chinese will be available Feature overview Phone lost alert Caller ID Music Control (possible volume control) Wireless Charging Timer Stopwatch Vibrating Alarm (possibly custom vibrations for caller id) A few default watch faces Airplane mode (by demand or low power) Can be turned off completely Customizable 3rd party watch faces, applications which can be loaded over bluetooth. Sample apps that maybe installed Weather Sample Apps not installed Exercise App Other Possible Skype integration over Bluetooth. They will provide an AGENT app for your smartphone (iPhone, Android, Windows Phone). You'll be able to use it to load apps onto the watch.. You will be able to cancel phone calls. With compatible phones you can also answer, end, etc. They are adopting the standard hands-free profile to provide these features and caller ID.

  Read the article

• C# HashSet<T>

  - by Ben Griswold

  I hadn’t done much (read: anything) with the C# generic HashSet until I recently needed to produce a distinct collection.  As it turns out, HashSet<T> was the perfect tool. As the following snippet demonstrates, this collection type offers a lot: // Using HashSet<T>: // http://www.albahari.com/nutshell/ch07.aspx var letters = new HashSet<char>("the quick brown fox");   Console.WriteLine(letters.Contains('t')); // true Console.WriteLine(letters.Contains('j')); // false   foreach (char c in letters) Console.Write(c); // the quickbrownfx Console.WriteLine();   letters = new HashSet<char>("the quick brown fox"); letters.IntersectWith("aeiou"); foreach (char c in letters) Console.Write(c); // euio Console.WriteLine();   letters = new HashSet<char>("the quick brown fox"); letters.ExceptWith("aeiou"); foreach (char c in letters) Console.Write(c); // th qckbrwnfx Console.WriteLine();   letters = new HashSet<char>("the quick brown fox"); letters.SymmetricExceptWith("the lazy brown fox"); foreach (char c in letters) Console.Write(c); // quicklazy Console.WriteLine(); The MSDN documentation is a bit light on HashSet<T> documentation but if you search hard enough you can find some interesting information and benchmarks. But back to that distinct list I needed… // MSDN Add // http://msdn.microsoft.com/en-us/library/bb353005.aspx var employeeA = new Employee {Id = 1, Name = "Employee A"}; var employeeB = new Employee {Id = 2, Name = "Employee B"}; var employeeC = new Employee {Id = 3, Name = "Employee C"}; var employeeD = new Employee {Id = 4, Name = "Employee D"};   var naughty = new List<Employee> {employeeA}; var nice = new List<Employee> {employeeB, employeeC};   var employees = new HashSet<Employee>(); naughty.ForEach(x => employees.Add(x)); nice.ForEach(x => employees.Add(x));   foreach (Employee e in employees) Console.WriteLine(e); // Returns Employee A Employee B Employee C The Add Method returns true on success and, you guessed it, false if the item couldn’t be added to the collection.  I’m using the Linq ForEach syntax to add all valid items to the employees HashSet.  It works really great.  This is just a rough sample, but you may have noticed I’m using Employee, a reference type.  Most samples demonstrate the power of the HashSet with a collection of integers which is kind of cheating.  With value types you don’t have to worry about defining your own equality members.  With reference types, you do. internal class Employee {     public int Id { get; set; }     public string Name { get; set; }       public override string ToString()     {         return Name;     }          public bool Equals(Employee other)     {         if (ReferenceEquals(null, other)) return false;         if (ReferenceEquals(this, other)) return true;         return other.Id == Id;     }       public override bool Equals(object obj)     {         if (ReferenceEquals(null, obj)) return false;         if (ReferenceEquals(this, obj)) return true;         if (obj.GetType() != typeof (Employee)) return false;         return Equals((Employee) obj);     }       public override int GetHashCode()     {         return Id;     }       public static bool operator ==(Employee left, Employee right)     {         return Equals(left, right);     }       public static bool operator !=(Employee left, Employee right)     {         return !Equals(left, right);     } } Fortunately, with Resharper, it’s a snap. Click on the class name, ALT+INS and then follow with the handy dialogues. That’s it. Try out the HashSet<T>. It’s good stuff.

  Read the article

• ODI and OBIEE 11g Integration

  - by David Allan

  Here we will see some of the connectivity options to OBIEE 11g using the JDBC driver. You’ll see based upon some connection properties how the physical or presentation layers can be utilized. In the integrators guide for OBIEE 11g you will find a brief statement indicating that there actually is a JDBC driver for OBIEE. In OBIEE 11g its now possible to connect directly to the physical layer, Venkat has an informative post here on this topic. In ODI 11g the Oracle BI technology is shipped with the product along with KMs for reverse engineering, and using OBIEE models for a data source. When you install OBIEE in 11g a light weight demonstration application is preinstalled in the server, when you open this in the BI Administration tool we see the regular 3 panel view within the administration tool. To interrogate this system via JDBC (just like ODI does using the KMs) need a couple of things; the JDBC driver from OBIEE 11g, a java client program and the credentials. In my java client program I want to connect to the OBIEE system, when I connect I can interrogate what the JDBC driver presents for the metadata. The metadata projected via the JDBC connection’s DatabaseMetadata changes depending on whether the property NQ_SESSION.SELECTPHYSICAL is set when the java client connects. Let’s use the sample app to illustrate. I have a java client program here that will print out the tables in the DatabaseMetadata, it will also output the catalog and schema. For example if I execute without any special JDBC properties as follows; java -classpath .;%BIHOMEDIR%\clients\bijdbc.jar meta_jdbc oracle.bi.jdbc.AnaJdbcDriver jdbc:oraclebi://localhost:9703/ weblogic mypass Then I get the following returned representing the presentation layer, the sample I used is XML, and has no schema; Catalog Schema Table Sample Sales Lite null Base Facts Sample Sales Lite null Calculated Facts …     Sample Targets Lite null Base Facts …     Now if I execute with the only difference being the JDBC property NQ_SESSION.SELECTPHYSICAL with the value Yes, then I see a different set of values representing the physical layer in OBIEE; java -classpath .;%BIHOMEDIR%\clients\bijdbc.jar meta_jdbc oracle.bi.jdbc.AnaJdbcDriver jdbc:oraclebi://localhost:9703/ weblogic mypass NQ_SESSION.SELECTPHYSICAL=Yes The following is returned; Catalog Schema Table Sample App Lite Data null D01 Time Day Grain Sample App Lite Data null F10 Revenue Facts (Order grain) …     System DB (Update me)     …     If this was a database system such as Oracle, the catalog value would be the OBIEE database name and the schema would be the Oracle database schema. Other systems which have real catalog structure such as SQLServer would use its catalog value. Its this ‘Catalog’ and ‘Schema’ value that is important when integration OBIEE with ODI. For the demonstration application in OBIEE 11g, the following illustration shows how the information from OBIEE is related via the JDBC driver through to ODI. In the XML example above, within ODI’s physical schema definition on the right, we leave the schema blank since the XML data source has no schema. When I did this at first, I left the default value that ODI places in the Schema field since which was ‘<Undefined>’ (like image below) but this string is actually used in the RKM so ended up not finding any tables in this schema! Entering an empty string resolved this. Below we see a regular Oracle database example that has the database, schema, physical table structure, and how this is defined in ODI.   Remember back to the physical versus presentation layer usage when we passed the special property, well to do this in ODI, the data server has a panel for properties where you can define key/value pairs. So if you want to select physical objects from the OBIEE server, then you must set this property. An additional changed in ODI 11g is the OBIEE connection pool support, this has been implemented via a ‘Connection Pool’ flex field for the Oracle BI data server. So here you set the connection pool name from the OBIEE system that you specifically want to use and this is used by the Oracle BI to Oracle (DBLINK) LKM, so if you are using this you must set this flex field. Hopefully a useful insight into some of the mechanics of how this hangs together.

  Read the article

• SQLAuthority News – Training and Consultancy and Travel – Story of 30 Last 30 Days

  - by pinaldave

  Today’s blog post is not technical as usual. Here, I present a real story, and I also invite you all to share your thoughts or opinions on this post. I am a professional SQL Server Trainer; I also do consultation in the area of the Performance Tuning and Query Optimizations. In any month, I like the mix of both in my schedule. I prefer to do training for one week, and then commit the next week for some consultation work. Due to the advancement in technology, for most of the consultation works, there is no client location visit or first time visit for understanding the project. Usually, I conduct high-end training sessions or 400 level training, and these training sessions are very intensive most of the time. Always after completing the training for 5 days straight away at 400 level, I make sure to take out some time to cool down and relax. During this time, I prefer to work on optimization projects. Consultancy is great as it keeps me updated regarding what is going on in the real world. As we all know, all those trainers who have real world experience are always considered to be the best trainers. My learning is immense during my consultations with the real client and while resolving real problems. I share the same with my students the very next week when I go for training sessions. For the same reason, every class is different from the previous ones. An experience trainer would tell you that the class is best if it is driven by Students the way instructor wants! The best scenario is as described above; but you won’t get the best scenario all the time. I was on road for nearly 25 days out of the last 30 days and involved in doing various SQL Server-related trainings. Here is what I have done in the last 30 days. I have gathered the following details from my expenditure reports, which are maintained by my wife. There are few points related to my personal expenses and few other related to business. I maintain a separate list for each of these expenses, but here I have aggregated them. Last 30 days - Training 23 days - 4 – two days training classes – 8 days of training 3 – five days training classes – 15 days of training 1 – one day training classes – 2 days of training Flights 18 flights - 8 – Kingfisher 6 – Spicejet 2 – Jet light 2 – Jet connect Stay in different cities Hyderabad – 16 days Chennai – 6 days Bangalore – 2 days Ahmedabad – 6 days (Hometown) Meals – 54 (Averaging less than 2 per day) Room Services – 16 times Training Campuses – 20 times Restaurants – 6 times Home – 12 times Taxi/Cabs – 64 times (Averaging more than 2 per day) Hotel Cab – 34 times Meru Cab – 8 times Easy Cabs – 10 times Auto Rickshaw – 2 times Looking at the above statistics, I can see that I have eaten less than what I should have, which is not good, and traveled in taxi more than what I should have. Also the temperatures in different cities were very different, not to mention the humidity as well. I missed my family, especially my little girl (9 months). When I was at home, I used to have a proper healthy meal every single day; however, when I was traveling, the food was something I had to compromise on. I have previously written about my travel experience with different airlines, my opinion is still same about them. Well, I have question to all of you road warriors, how do you manage your health and enthusiasm during situations I am going through. I have couple of time stomach upset as well sour throat. I drink lots of water and do my best to keep up. Any idea? Reference: Pinal Dave (http://blog.SQLAuthority.com) Filed under: About Me, Pinal Dave, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

< Previous Page | 123 124 125 126 127 128 129 130 131 132 133 134  | Next Page >