Search Results

Search found 8089 results on 324 pages for 'auto completion'.

Page 128/324 | < Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >

• QLogic QLE8152 won't link up with a fiber loop

  - by Mike Pennington

  I have a Dell R710 running Debian Linux 6.0 (Squeeze). I installed a QLogic QLE8152 CNA in the PCI-E riser today and I have been trying to get the CNA's ethernet layer to come up after I put a fiber loop on it; I also scoped it with a light meter, and the SFP+ transceiver is getting the correct amount of light. The whole time I have been working on this problem, the lights on the CNA are blinking green at a rate of about 1 flash every 3 seconds. When I plug the fiber into a Juniper EX4500 10GE in a rack next to it, the Juniper's link stays down as well. I have to confess that this is my first wrangling with a CNA, so perhaps I'm doing something fundamentally wrong, but here is what I have found so far... First the basics... [mpenning@Finger ~]$ uname -a Linux Finger 2.6.32-5-amd64 #1 SMP Mon Oct 3 03:59:20 UTC 2011 x86_64 GNU/Linux [mpenning@Finger ~]$ cat /etc/issue Debian GNU/Linux 6.0 \n \l [mpenning@Finger ~]$ lspci -v shows that the card is properly installed (physically) 04:00.0 Ethernet controller: QLogic Corp. 10GbE Converged Network Adapter (TCP/IP Networking) (rev 02) Subsystem: QLogic Corp. Device 017e Flags: bus master, fast devsel, latency 0, IRQ 34 I/O ports at e000 [size=256] Memory at df8f0000 (64-bit, non-prefetchable) [size=16K] Memory at df900000 (64-bit, non-prefetchable) [size=1M] Expansion ROM at df800000 [disabled] [size=256K] Capabilities: [44] Power Management version 3 Capabilities: [4c] Express Endpoint, MSI 00 Capabilities: [88] MSI: Enable- Count=1/32 Maskable- 64bit+ Capabilities: [98] Vital Product Data Capabilities: [a0] MSI-X: Enable+ Count=8 Masked- Capabilities: [100] Advanced Error Reporting Capabilities: [138] Device Serial Number 00-c0-dd-ff-fe-1c-53-b4 Capabilities: [144] Power Budgeting <?> Kernel driver in use: qlge The output from ethtool shows that eth4 is the QLE8152... [mpenning@Finger ~]$ sudo ethtool eth4 Settings for eth4: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 0 Transceiver: external Auto-negotiation: on Current message level: 0x000060f7 (24823) Link detected: no [mpenning@Finger ~]$ sudo ethtool -i eth4 driver: qlge version: v1.00.00-b3 firmware-version: v1.35.11 bus-info: 0000:04:00.0 [mpenning@Finger ~]$ Finally, I tried modprobe -r qlge; modprobe -r qla2xxx and then modprobe qla2xxx; modprobe qlge to kick the system again... I don't see a smoking gun in /var/log/messages... Nov 17 19:46:21 finger kernel: [ 6212.298275] qlge 0000:04:00.1: PCI INT B disabled Nov 17 19:46:22 finger kernel: [ 6213.779974] qlge 0000:04:00.0: PCI INT A disabled Nov 17 19:46:33 finger kernel: [ 6224.554074] qla2xxx 0000:04:00.3: PCI INT D disabled Nov 17 19:46:33 finger kernel: [ 6224.555322] qla2xxx 0000:04:00.2: PCI INT C disabled Nov 17 19:46:54 finger kernel: [ 6245.625854] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:54 finger kernel: [ 6245.625888] qla2xxx 0000:04:00.2: PCI INT C -> GSI 35 (level, low) -> IRQ 35 Nov 17 19:46:54 finger kernel: [ 6245.626837] qla2xxx 0000:04:00.2: MSI-X vector count: 7 Nov 17 19:46:54 finger kernel: [ 6245.626841] qla2xxx 0000:04:00.2: Found an ISP8001, irq 35, iobase 0xffffc90012664000 Nov 17 19:46:54 finger kernel: [ 6245.627113] qla2xxx 0000:04:00.2: Configuring PCI space... Nov 17 19:46:54 finger kernel: [ 6245.639429] qla2xxx 0000:04:00.2: Configure NVRAM parameters... Nov 17 19:46:54 finger kernel: [ 6245.642597] qla2xxx 0000:04:00.2: Verifying loaded RISC code... Nov 17 19:46:54 finger kernel: [ 6245.642708] qla2xxx 0000:04:00.2: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.273340] qla2xxx 0000:04:00.2: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.273401] qla2xxx 0000:04:00.2: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.273486] qla2xxx 0000:04:00.2: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.273856] scsi9 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.274631] qla2xxx 0000:04:00.2: Nov 17 19:46:55 finger kernel: [ 6246.274633] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.274634] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.274636] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.2 hdma+, host#=9, fw=5.01.04 (8d4) Nov 17 19:46:55 finger kernel: [ 6246.274666] qla2xxx 0000:04:00.3: PCI INT D -> GSI 37 (level, low) -> IRQ 37 Nov 17 19:46:55 finger kernel: [ 6246.274748] qla2xxx 0000:04:00.3: MSI-X vector count: 7 Nov 17 19:46:55 finger kernel: [ 6246.274751] qla2xxx 0000:04:00.3: Found an ISP8001, irq 37, iobase 0xffffc900125c4000 Nov 17 19:46:55 finger kernel: [ 6246.275098] qla2xxx 0000:04:00.3: Configuring PCI space... Nov 17 19:46:55 finger kernel: [ 6246.287329] qla2xxx 0000:04:00.3: Configure NVRAM parameters... Nov 17 19:46:55 finger kernel: [ 6246.290624] qla2xxx 0000:04:00.3: Verifying loaded RISC code... Nov 17 19:46:55 finger kernel: [ 6246.290736] qla2xxx 0000:04:00.3: FW: Loading from flash (a0000)... Nov 17 19:46:55 finger kernel: [ 6246.920204] qla2xxx 0000:04:00.3: Allocated (64 KB) for FCE... Nov 17 19:46:55 finger kernel: [ 6246.920264] qla2xxx 0000:04:00.3: Allocated (64 KB) for EFT... Nov 17 19:46:55 finger kernel: [ 6246.920345] qla2xxx 0000:04:00.3: Allocated (1350 KB) for firmware dump... Nov 17 19:46:55 finger kernel: [ 6246.920749] scsi10 : qla2xxx Nov 17 19:46:55 finger kernel: [ 6246.921715] qla2xxx 0000:04:00.3: Nov 17 19:46:55 finger kernel: [ 6246.921716] QLogic Fibre Channel HBA Driver: 8.03.01-k6 Nov 17 19:46:55 finger kernel: [ 6246.921717] QLogic QLE8152 - QLogic PCI-Express Dual Channel 10GbE CNA Nov 17 19:46:55 finger kernel: [ 6246.921719] ISP8001: PCIe (5.0GT/s x4) @ 0000:04:00.3 hdma+, host#=10, fw=5.01.04 (8d4) Nov 17 19:46:58 finger kernel: [ 6249.519911] qlge 0000:04:00.0: PCI INT A -> GSI 34 (level, low) -> IRQ 34 Nov 17 19:46:58 finger kernel: [ 6249.533970] qlge 0000:04:00.0: QLogic 10 Gigabit PCI-E Ethernet Driver Nov 17 19:46:58 finger kernel: [ 6249.533975] qlge 0000:04:00.0: Driver name: qlge, Version: v1.00.00-b3. Nov 17 19:46:58 finger kernel: [ 6249.534856] qlge 0000:04:00.0: ql_display_dev_info: Function #0, Port 0, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.534860] qlge 0000:04:00.0: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b4 Nov 17 19:46:58 finger kernel: [ 6249.534888] qlge 0000:04:00.1: PCI INT B -> GSI 44 (level, low) -> IRQ 44 Nov 17 19:46:58 finger kernel: [ 6249.549109] qlge 0000:04:00.1: ql_display_dev_info: Function #1, Port 1, NIC Roll 0, NIC Rev = 1, XG Roll = 0, XG Rev = 1. Nov 17 19:46:58 finger kernel: [ 6249.549112] qlge 0000:04:00.1: ql_display_dev_info: MAC address 00:c0:dd:1c:53:b6 Any assistance getting a link up on this is greatly appreciated...

  Read the article

• LSI MegaRAID Expected Chip Temperature?

  - by Myles Gray

  We recently built a replicating SAN array from 2x Dell R720XD's, we are using LSI 9270-8i MegaRAID cards with CacheCade 2.0, BBU and Write Back cache enabled. Our cards are showing HUGE chip temperatures (97*C+ with NO disk activity!). Our R720's are in auto temp management mode so the max exhaust temp is 50*C. The MegaRAID cards are passively cooled and depend on good airflow to cool them - however is 97*C normal? - I have seen reference to 60*C max ambients but nothing for chip temp.

  Read the article

• how to rollback/undo yum update on fedora after messing the fedora versions

  - by misteryes

  I want to install texlive on my fedora 16 laptop with the following procedure: # yum remove tex-* texlive-* # cat > /etc/yum.repos.d/texlive.repo <<EOF [texlive] name=texlive baseurl=http://jnovy.fedorapeople.org/texlive/2012/packages.f17/ enabled=1 gpgcheck=0 EOF # yum update; # yum install texlive after yum update, I notice that my laptop is fedora 16, while I used 2012/packages.fc17/ so I modify /etc/yum.repos.d/texlive.repo to use 2011/packages.fc16 and do yum update again however, there are many errors [root@kitty esolve]# yum update Loaded plugins: auto-update-debuginfo, langpacks, presto, refresh-packagekit http://repos.fedorapeople.org/repos/leigh123linux/cinnamon/fedora-16/x86_64/repodata/repomd.xml: [Errno 14] HTTP Error 404 - Not Found : http://repos.fedorapeople.org/repos/leigh123linux/cinnamon/fedora-16/x86_64/repodata/repomd.xml Trying other mirror. Setting up Update Process Resolving Dependencies --> Running transaction check ---> Package dvipng.x86_64 0:1.14-1.fc15 will be obsoleted ---> Package kpathsea.x86_64 0:2007-66.fc16 will be obsoleted --> Processing Dependency: libkpathsea.so.4()(64bit) for package: evince-dvi-3.2.1-2.fc16.x86_64 ---> Package mkvtoolnix.x86_64 0:5.8.0-1 will be updated ---> Package mkvtoolnix.x86_64 0:6.3.0-1 will be an update ---> Package nautilus-dropbox.x86_64 0:1.4.0-1.fc10 will be updated ---> Package nautilus-dropbox.x86_64 0:1.6.0-1.fc10 will be an update ---> Package texlive-dvipng-bin.x86_64 2:svn26509.0-19.20130317_r29408.fc17 will be obsoleting --> Processing Dependency: texlive-kpathsea-lib = 2:2012-19.20130317_r29408.fc17 for package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 --> Processing Dependency: texlive-base for package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 --> Processing Dependency: tex-dvipng for package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 --> Processing Dependency: libpng15.so.15()(64bit) for package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 --> Processing Dependency: libkpathsea.so.6()(64bit) for package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 ---> Package texlive-kpathsea.noarch 2:svn28792.0-19.fc17 will be obsoleting --> Processing Dependency: texlive-kpathsea-bin for package: 2:texlive-kpathsea-svn28792.0-19.fc17.noarch --> Running transaction check ---> Package kpathsea.x86_64 0:2007-66.fc16 will be obsoleted --> Processing Dependency: libkpathsea.so.4()(64bit) for package: evince-dvi-3.2.1-2.fc16.x86_64 ---> Package texlive-base.noarch 2:2012-19.20130317_r29408.fc17 will be installed ---> Package texlive-dvipng.noarch 2:svn26689.1.14-19.fc17 will be installed ---> Package texlive-dvipng-bin.x86_64 2:svn26509.0-19.20130317_r29408.fc17 will be obsoleting --> Processing Dependency: libpng15.so.15()(64bit) for package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 ---> Package texlive-kpathsea-bin.x86_64 2:svn27347.0-19.20130317_r29408.fc17 will be installed ---> Package texlive-kpathsea-lib.x86_64 2:2012-19.20130317_r29408.fc17 will be installed --> Finished Dependency Resolution Error: Package: evince-dvi-3.2.1-2.fc16.x86_64 (@fedora) Requires: libkpathsea.so.4()(64bit) Removing: kpathsea-2007-66.fc16.x86_64 (@so-updates) libkpathsea.so.4()(64bit) Obsoleted By: 2:texlive-kpathsea-svn28792.0-19.fc17.noarch (texlive) Not found Error: Package: 2:texlive-dvipng-bin-svn26509.0-19.20130317_r29408.fc17.x86_64 (texlive) Requires: libpng15.so.15()(64bit) You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest and when I do yum install texlive, it simply tries to install the f17 version, which failed. what Can I do to install f16 version? how can I undo yum update with 2012/packages.f17/ I tried yum history, and for today's history, I only have Loaded plugins: auto-update-debuginfo, langpacks, presto, refresh-packagekit ID | Login user | Date and time | Action(s) | Altered ------------------------------------------------------------------------------- 124 | esolve ... <esolve> | 2013-09-12 18:35 | Erase | 24 123 | root <root> | 2013-08-23 11:08 | Update | 1 122 | root <root> | 2013-08-21 14:13 | Update | 1 < 121 | esolve ... <esolve> | 2013-05-31 15:36 | Install | 1 > 120 | root <root> | 2013-05-29 15:13 | Install | 1 < 119 | root <root> | 2013-04-18 13:13 | Update | 1 >< which seems not related to yum update the history results: 1003 yum update 1004 vim 1005 vim /etc/yum.repos.d/texlive.repo 1006 yum update 1007 yum install texlive 1008 vim /etc/yum.repos.d/texlive.repo 1009 clear 1010 yum history 1011 yum history list 1012 vim 1013 vim /etc/yum.repos.d/texlive.repo 1014 yum history list 1015 history also I tried yum history undo 124 but it failed! [root@kitty esolve]# yum history undo 124 Loaded plugins: auto-update-debuginfo, langpacks, presto, refresh-packagekit http://repos.fedorapeople.org/repos/leigh123linux/cinnamon/fedora-16/x86_64/repodata/repomd.xml: [Errno 14] HTTP Error 404 - Not Found : http://repos.fedorapeople.org/repos/leigh123linux/cinnamon/fedora-16/x86_64/repodata/repomd.xml Trying other mirror. Undoing transaction 124, from Thu Sep 12 18:35:31 2013 Erase R-2.14.1-1.fc16.x86_64 ? Erase R-core-2.14.1-1.fc16.x86_64 ? Erase R-devel-2.14.1-1.fc16.x86_64 ? Erase a2ps-4.14-12.fc15.x86_64 ? Erase docbook-utils-pdf-0.6.14-29.fc16.noarch ? Erase html2ps-1.0-0.7.b7.fc15.noarch ? Erase jadetex-3.13-10.fc15.noarch ? Erase kile-2.1.1-1.fc16.x86_64 ? Erase linuxdoc-tools-0.9.66-9.fc15.x86_64 ? Erase tetex-dvipost-1.1-12.fc15.x86_64 ? Erase tex-cm-lgc-0.5-18.fc15.noarch ? Erase tex-preview-11.86-6.fc16.noarch ? Erase texinfo-tex-4.13a-15.fc15.x86_64 ? Erase texlive-2007-66.fc16.x86_64 ? Erase texlive-dvips-2007-66.fc16.x86_64 ? Erase texlive-latex-2007-66.fc16.x86_64 ? Erase texlive-texmf-2007-40.fc16.noarch ? Erase texlive-texmf-dvips-2007-40.fc16.noarch ? Erase texlive-texmf-fonts-2007-40.fc16.noarch ? Erase texlive-texmf-latex-2007-40.fc16.noarch ? Erase texlive-utils-2007-66.fc16.x86_64 ? Erase texmaker-1:3.2.2-1.fc16.x86_64 ? Erase texmf-RR-Inria-4.11-inria.0.noarch ? Erase xdvik-22.84.14-9.fc15.x86_64 ? Error: No package(s) available to install

  Read the article

• Spamassassin not work

  - by John

  I set the threshold to 7.5. But this mail still can't work thought will auto spam. Any idea? Thanks. X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on X-Spam-Level: * X-Spam-Status: Yes, score=5.9 required=5.0 tests=DNS_FROM_OPENWHOIS, FH_DATE_PAST_20XX,HTML_MESSAGE,RDNS_NONE autolearn=no version=3.2.

  Read the article

• How to change Blackberry initial message download limit.

  - by Mikey B

  BES 4.1.6 Blackberry 8300 (curve) Hi guys, I've noticed that handhelds will typically only retrieve the first few KB and then prompt the user to manually retrieve more (or auto-retrieve if they scroll down). The problem is that I have a BB app that needs to see the entire message all at once on the first initial time it's opened. Is there a setting on BES that will allow me to change how much data a handheld initially retrieves per message? Thanks, M

  Read the article

• Coldfusion autorestart

  - by Comcar

  Coldfusion is automatically restarting, a lot. It comes in waves, everything seems fine for a while then the server struggles for a few minutes, restarts a lot then settles down again. I have Fusion Reactor installed, but when CF goes down FR stops logging so it's not really helping. Looking through the archived logs just shows gaps in the logs. These are all the occourances of the phrase "Coldfusion started" today. [root@server2 logs]# grep -i "Coldfusion started" server.log | grep "11/27/12" "Information","main","11/27/12","01:49:35",,"ColdFusion started" "Information","main","11/27/12","01:50:46",,"ColdFusion started" "Information","main","11/27/12","01:52:39",,"ColdFusion started" "Information","main","11/27/12","01:54:08",,"ColdFusion started" "Information","main","11/27/12","01:55:12",,"ColdFusion started" "Information","main","11/27/12","01:56:29",,"ColdFusion started" "Information","main","11/27/12","01:57:36",,"ColdFusion started" "Information","main","11/27/12","01:58:57",,"ColdFusion started" "Information","main","11/27/12","01:59:56",,"ColdFusion started" "Information","main","11/27/12","02:01:38",,"ColdFusion started" "Information","main","11/27/12","02:03:11",,"ColdFusion started" "Information","main","11/27/12","02:04:41",,"ColdFusion started" "Information","main","11/27/12","02:07:53",,"ColdFusion started" "Information","main","11/27/12","02:10:45",,"ColdFusion started" "Information","main","11/27/12","02:11:49",,"ColdFusion started" "Information","main","11/27/12","02:13:09",,"ColdFusion started" "Information","main","11/27/12","02:14:18",,"ColdFusion started" "Information","main","11/27/12","02:15:44",,"ColdFusion started" "Information","main","11/27/12","02:17:06",,"ColdFusion started" "Information","main","11/27/12","02:34:19",,"ColdFusion started" "Information","main","11/27/12","03:01:20",,"ColdFusion started" "Information","main","11/27/12","05:25:59",,"ColdFusion started" "Information","main","11/27/12","06:30:48",,"ColdFusion started" "Information","main","11/27/12","06:36:20",,"ColdFusion started" "Information","main","11/27/12","09:34:07",,"ColdFusion started" "Information","main","11/27/12","09:35:39",,"ColdFusion started" "Information","main","11/27/12","09:36:41",,"ColdFusion started" "Information","main","11/27/12","09:39:15",,"ColdFusion started" "Information","main","11/27/12","09:40:42",,"ColdFusion started" "Information","main","11/27/12","09:42:55",,"ColdFusion started" "Information","main","11/27/12","09:44:23",,"ColdFusion started" "Information","main","11/27/12","09:46:18",,"ColdFusion started" "Information","main","11/27/12","09:47:35",,"ColdFusion started" "Information","main","11/27/12","09:48:53",,"ColdFusion started" "Information","main","11/27/12","09:50:04",,"ColdFusion started" "Information","main","11/27/12","09:51:51",,"ColdFusion started" "Information","main","11/27/12","09:53:05",,"ColdFusion started" "Information","main","11/27/12","09:54:24",,"ColdFusion started" "Information","main","11/27/12","09:55:28",,"ColdFusion started" "Information","main","11/27/12","09:56:38",,"ColdFusion started" "Information","main","11/27/12","09:58:03",,"ColdFusion started" "Information","main","11/27/12","09:59:03",,"ColdFusion started" "Information","main","11/27/12","10:04:37",,"ColdFusion started" "Information","main","11/27/12","12:04:02",,"ColdFusion started" I've been looking at the live server metrics in FR on a second screen all day, the CPU, Memory and requests all seemed fine about 12 midday, then the server rebooted. Looking at the logs for the hour between 9am and 10am (more than 15 restarts in the hour), the CPU never went over 44% usage and the Memory never exceeded 53% usage - in the recorded stats at least. There is no JDBC tracking at the moment, so I'll add that to tracking and see if it's MySQL causing a problem, but can anyone help me narrow down the problem, what would cause Cold Fusion to auto restart, and I'm assuming the auto restart is only happening because Fusion Reactor is installed. It's a Red Hat 5 LAMP stack running Coldfusion 9 and Fusion Reactor 4.5.2

  Read the article

• How to fix network connection dead on startup, but okay after disable/enable?

  - by bill weaver

  on Startup When my system starts up, the internet connection is dead. This causes various problems with startup items such as updates and auto-start programs failing. However, the connection is fine after going into Network and Sharing, Change adapter settings, then disabling and re-enabling the adapter. Any suggestions on why this is happening and how to fix it? System summary: Windows 7, 64 bit, Realtek PCIe GBE Family Controller, Linksys WRT610N router, Sci Atlanta cable modem.

  Read the article

• touch /forcefsck not working on Fedora16

  - by Harry

  I need to run fsck in order to repair my one and only hard-disk. I have no rescue CD/USB available. I did the following: touch /forcefsck chmod a+rw /forcefsck # just to be really sure reboot But no fsck happened on reboot, though the /forcefsck file quietly disappeared (why BTW?)! I saw some responses on the Net suggesting a shutdown -rF to auto-run fsck on reboot, but the shutdown I have on my F16 does not have any -F option.

  Read the article

• windows server 2003 - terminal server - hide taskbar

  - by s.mihai

  Hello, We've got arround 25users connecting to our terminal server (remote desktop) - no active directory is used. How can i hide the taskbar from the bottom of the page, not to auto-hide it. i want the users not to be able to use it (except the administrators of course). Mike

  Read the article

• vim indentation for bullet lists

  - by Oliver

  hi, all I often write text with format like this in VIM My talking points: - talking point 1 - talking point 2 .... continue on point 2 Ideally, I would hope VIM can auto align it for me such as: - talking point 1 - talking point 2 continue on point 2 Is this possible? thanks Oliver

  Read the article

• vim format help

  - by Oliver

  hi, all I often write text with format like this in VIM My talking points: - talking point 1 - talking point 2 .... continue on point 2 Ideally, I would hope VIM can auto align it for me such as: - talking point 1 - talking point 2 continue on point 2 Is this possible? thanks Oliver

  Read the article

• IPSEC site-to-site Openswan to Cisco ASA

  - by Jim

  I recieved a list of commands that were run on the right side of the VPN tunnel which is where the Cisco ASA resides. On my side, I have a linux based firewall running debian with openswan installed. I am having an issue with getting to Phase 2 of the VPN negotiation. Here is the Cisco Information I was sent: {my_public_ip} = left side of connection tunnel-group {my_public_ip} type ipsec-l2l tunnel-group {my_public_ip} ipsec-attributes pre-shared-key fakefake crypto map vpn1 1 match add customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside static (outside,inside) 10.2.1.200 {my_public_ip} netmask 255.255.255.255 crypto ipsec transform-set aes-256-sha esp-aes-256 esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map vpn1 1 match address customer-ipsec crypto map vpn1 1 set peer {my_public_ip} crypto map vpn1 1 set transform-set aes-256-sha crypto map vpn1 interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 Myside ipsec.conf config setup klipsdebug=none plutodebug=none protostack=netkey #nat_traversal=yes conn cisco #name of VPN connection type=tunnel authby=secret #left side (myside) left={myPublicIP} leftsubnet=172.16.250.0/24 #net subnet on left sdie to assign to right side leftnexthop=%defaultroute #right security gateway (ASA side) right={CiscoASA_publicIP} #cisco ASA rightsubnet=10.2.1.0/24 rightnexthop=%defaultroute #crypo stuff keyexchange=ike ikelifetime=86400s auth=esp pfs=no compress=no auto=start ipsec.secrets file {CiscoASA_publicIP} {myPublicIP}: PSK "fakefake" When I start ipsec from the left side/my side I don't recieve any errors, however when I run the ipsec auto --status command: 000 "cisco": 172.16.250.0/24==={left_public_ip}<{left_public_ip}>[+S=C]---{left_public_ip_gateway}...{left_public_ip_gateway}--{right_public_ip}<{right_public_ip}>[+S=C]===10.2.1.0/24; prospective erouted; eroute owner: #0 000 "cisco": myip=unset; hisip=unset; 000 "cisco": ike_life: 86400s; ipsec_life: 28800s; rekey_margin: 540s; rekey_fuzz: 100%; keyingtries: 0 000 "cisco": policy: PSK+ENCRYPT+TUNNEL+UP+IKEv2ALLOW+SAREFTRACK+lKOD+rKOD; prio: 24,24; interface: eth0; 000 "cisco": newest ISAKMP SA: #0; newest IPsec SA: #0; 000 000 #2: "cisco":500 STATE_MAIN_I1 (sent MI1, expecting MR1); EVENT_RETRANSMIT in 10s; nodpd; idle; import:admin initiate 000 #2: pending Phase 2 for "cisco" replacing #0 Now I'm new to setting up an site-to-site IPSEC tunnel so the status informatino I am unsure what it means. All I know is it sits at this "pending Phase 2" and I can't ping the other side, Another question I have is, if I do a route -n, should I see anything relating to this connection? Also, I read a few artilcle where configs contained the interface="ipsec0=eth0", is this an interface that I have to create on the linux debian firewall on my side? Appreciate your time to look at this.

  Read the article

• iphone dictionary autocorrect [closed]

  - by Raj More

  I have the iPhone 3G with OS 3.1 3.0.1 on it. Every time I type a text message that includes the word "me", it gets auto corrected to "mr". So my friends get a text that says "call mr when you get done" or "jack told mr about it yesterday" how do i change this autocorrect so it stops changing my "me" to a "mr"?

  Read the article

• Ubuntu 10.04 server, problems installing the desktop

  - by ILMV

  Hi all, I have just setup two servers running 10.04 server and have installed the ubuntu-desktop as follows: sudo apt-get install ubuntu-desktop The problem is even though it says it has installed it will not auto-start... I've tried this: sudo mv /etc/init/gdm.conf /etc/init/gdm.disabled sudo mv /etc/init/gdm.disabled /etc/init/gdm.conf To enable/disable it but still not joy. Any ideas? Thanks, Ben

  Read the article

• Excluding Environment Variables from ZSH Autocomplete

  - by Bryan Veloso

  Quick example: ~ $ wor<TAB> ~ $ WORDCHARS= WORDCHARS WORKON_HOME WORKON_HOME workon workon is the desired command. Is there a way to exclude the environment variables from auto-completing in ZSH?

  Read the article

• GNU info pages BLOW

  - by mbac32768

  How many times have you looked up a man page only to discover that it's useless and you're told to view the info page instead? Well, info is an abortion and I refuse to use it. How do you cope? Lets the healing begin. Curious if anyone has a nifty 'man' wrapper that auto-magically probes for an info document and converts that into a man page on-the-fly.

  Read the article

• Windows 7 Forbid connecting to a specific wireless network

  - by Elliot

  Does anyone know how to tell windows 7 to bar a wireless network? It keeps logging into a random open one with no bandwidth my neighbors have instead of the good one we have here. I keep unchecking "automatically log in if available" and it keeps re-checking itself. I want it to NEVER log into this network no matter what without manual intervention. I do not want to disable auto connecting, just tell it "do not ever connect to this one without my express permission".

  Read the article

• Where is the "fix" button on Windows 7 Photo Viewer?

  - by Edward Tanguay

  When I click on a photo in Vista I get a fix button: When I click on a photo in Windows 7 I don't get a fix button: I used to use this fix button often to fix red-eye and alter the brightness quickly, and the auto-saving was so fast. If I can't get "Windows Photo Viewer" to do this, I'll have to http://www.irfanview.com again to do this.

  Read the article

• Looking for a AutoZoom browser plugin

  - by AngryHacker

  I have a pretty large 24" wide screen with a pretty high resolution. When I browse, some sites have a fixed layout and there is basically a narrow column. So I typically zoom in to the point just before the level where I have to scroll horizontally. Is there a browser plugin that auto-zooms in (or via a button or gesture or whatever) to the max available real estate? I'd prefer a plugin for Chrome, but Firefox will do too.

  Read the article

• nmap: easily Ping-Scan all addresses in my subnet

  - by Felipe Alvarez

  Is there an nmap line that will auto-detect my current IP address and subnet mask, and run a ping-scan on all? For example: #> nmap -sP 0.0.0.0 Instead of manually: #> nmap -sP 192.168.100.0/24

  Read the article

• Disable Outlook SplashScreen when autostarting

  - by serhio

  I have set up outlook 2003 to auto-start and hide to icon. Now, every time I start my computer I see the Outlook splash screen, and this makes me thing that it slows OS to become "operational" after startup.

  Read the article

• Accessing guests on virtual network when connected to host via PPTP

  - by Viktor Elofsson

  I'm setting up a development machine which runs Ubuntu 12.04 and KVM for virtualization. I have a guest running Ubuntu 12.04 which can be accessed from the host via its IP address which is assigned by libvirt. The guest can also access the internet, no problem there. However, now I want to setup PPTP so I can connect to the host (from my workstation running Windows 7) and directly access guests without relying on SSH port forwarding. I can connect from my W7-machine to the host (PPTP), but I cannot access any virtual machines (which are accessable from the host directly). Relevant configuration files cat /etc/network/interfaces auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address x.x.x.x broadcast x.x.x.x netmask x.x.x.x gateway x.x.x.x # default route to access subnet up route add -net x.x.x.x netmask x.x.x.x gw x.x.x.x eth0 virsh net-edit default <network> <name>default</name> <uuid>xxxxxxxx-72ce-3c20-af0f-d3a010f1bef0</uuid> <forward mode='nat'/> <bridge name='virbr0' stp='on' delay='0' /> <mac address='52:54:00:xx:xx:xx'/> <ip address='192.168.122.1' netmask='255.255.255.0'> <dhcp> <range start='192.168.122.2' end='192.168.122.254' /> <host mac='52:54:00:yy:yy:yy' name='web1' ip='192.168.122.11' /> </dhcp> </ip> </network> cat /etc/pptpd.conf (commented lines removed) # TAG: option # Specifies the location of the PPP options file. # By default PPP looks in '/etc/ppp/options' # option /etc/ppp/pptpd-options # TAG: logwtmp # Use wtmp(5) to record client connections and disconnections. # logwtmp #(Recommended) localip 192.168.122.1 remoteip 192.168.122.234-238,192.168.122.245 cat /etc/ppp/chap-secrets* # Secrets for authentication using CHAP # client server secret IP addresses xxxxx * yyyyyyyyyy 192.168.122.100 I get the correct IP address when connecting my W7-machine, but when I try to ping the virtual machine at 192.168.122.11 I get Reply from 192.168.122.1: Destination port unreachable. It's probably something trivial I'm missing but I can't for the life of me figure out what it is. So I'm turning to you, serverfault.

  Read the article

• FreeBSD 8.0 - Macbook: Trying to Connect to Wireless

  - by Koroviev

  What Happened A few days ago I installed FreeBSD 8from USB to my Macbook (Core Duo, 13"). The first thing I wanted to do was get my GUI back. I'm new to FreeBSD and it's my first time off of mac or windows, so I had some learning to do. I tried to a make clean install of xorg with ports but it returned many "No address record" errors. I realised I hadn't configured network settings and then the fun started. I ran ifconfig and it found 5 devices: msk0, ath0, fwe0, fwip0, lo0. * ath0 was identified as media: IEEE 802.11 Wireless Ethernet autoselect so it was clear which one I needed. From what I gathered, there are 3 files and two processes involved here: /boot/loader.conf /etc/wpa_supplicant.conf /etc/rc.conf /etc/rc.d/netif wpa_supplicant (which is a part of the former too) I'm certain it's a big simplification, so correct me if I'm wrong here. What I Tried I configured /boot/loader.conf with the few basic settings, and I'm most sure that this file is okay. The other 2 were more puzzling. I tried to make a network package in wpa_supplicant.conf. I found the ssid of the router, but the security wasn't so easy. The routers configuration on security is set to "Auto", with no explanation given. Other options are there, but Auto is selected. Another laptop uses WEP to connect (it's Vista, so I don't know how to get any more info than that), but I never configured it to do it. There's a string labled "wireless key" on the bottom of the router which I entered to set it up a new machine on the network (Windows and Macs, so it was simplified). I never had to choose a security type and only learned about them by installing FreeBSD. So perhaps WEP is what "Auto" means, but I can't find any other evidence. wpa_supplicant.conf seemed to never be correctly configured. I always got errors related to it and WPA_supplicant doesn't work. It gave me "Can't disable/enable WPA in the driver" errors and more once when I enabled -d -d. This was when I was trying some suspect configurations in rc.conf though. Usually it does nothing except hijack the shell and print "CTRL-SCAN-EVENT-RESULT" every 10 seconds. I learned how to clone the ath0 device to a wlandev interface (wlan0). ath0 is associated to it and their connection seems to go smoothly. But the wlan0's connection to the network is the problem. I couldn't create this with rc.conf, I do something wrong and get ifconfig: create: bad value errors whenever it's parsed. I did it via the shell instead. What Now? I scanned with wlan0 today: ifconfig wlan0 list scan It shows my router, even my neighbour's router. It was a relief to finally get some feedback. So wlan0 is UP and detects the router, but it is always status: no carrier. It can't associate with it and I can't figure out why. Running /etc/rc.d/netif start returns almost the same result as ifconfig would. It shows lo0 and wlan0, and sometimes ath0. I still not sure what lo0 is doing. So; how do I associate with it? We can assume it's WEP security based on how the other laptop is setup. I'll give every relevant output here. After boot, with a blank rc.conf this is what ifconfig returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 I run: ifconfig wlan0 create wlandev ath0 It returns: wlan0: bpf attached wlan0: bpf attached wlan0: Ethernet address: xx:xx:xx:xx:xx:xx Ifconfig now returns: msk0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=11a<TXCSUM,VLAN_MTU,VLAN_HWTAGGING,TSO4> ether 00:17:f2:29:89:3b media: Ethernet autoselect ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 2290 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 02:17:f2:60:ad:7e ch 1 dma -1 fwip0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 lladdr 0.17.f2.ff.fe.60.ad.7e.a.2.ff.fe.0.0.0.0 lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 wlan0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 00:16:cb:bb:fe:65 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier ssid "" channel 1 (2412 Mhz 11b) regdomain 106 indoor ecm authmode OPEN privacy OFF txpower 20 bmiss 7 scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi 7 roam:rate 1 wme burst bintval 0 I run: ifconfig wlan0 up ifconfig wlan0 scan It finds my router and displays its details. I can feed it my routers details now, using: ifconfig wlan0 key value key value ... They show up in wlan0 when I run ifconfig, but it still doesn't associate. What details should I feed it, what exactly is needed? What, if anything, should I have in /etc/wpa_supplicant.conf (and if that psk is needed, is it most likely the string I mentioned above)? If I define the ssid in wpa_supplicant.conf, should I still feed it to wlan0? What process should I then use to associate it? 5 .How should I add these things to rc.conf so it will automatically do this at boot? A huge thank you in advance for any help you can give, I've spent hours crawling about the shell and I've learned quite a bit from it (I finally got the hang of vi too, from all that editing). But the sooner this is fixed, the better. *P.S. I was, and still am, wondering where the extra three devices come from (the wireless and wired were all I expected to find). lo0 is up at each boot and /etc/rc.d/netif, I have no idea what it is and can't find it in dmesg. Resources: /etc/loader.conf: Code: if_ath_load="YES" wlan_wep_load="YES" wlan_ccmp_load="YES" wlan_tkip_load="YES" /etc/wpa_supplicant.conf (I emptied it of everything unnecessary, because I was just causing errors) network={ ssid="BTVOYAGER2110-1C" } /etc/rc.conf has no network settings, I commented them out because of errors. There was my attempt to clone ath0 and feed it info, but I did if via the shell instead. I've included the output of dmesg as an attachment, in case it's useful. I'd include the boot text (which appears before login) but I don't know how to catch it into a text file. If it's needed and somebody tells me how, I will (actually, even if it's not needed, how can I view it to read?).

  Read the article

• Protecting DNS entries from duplicate hostnames entering network

  - by Aszurom

  Given a Windows domain, with DNS provided by a server on that domain, I am curious about what happens if a guest joins the network attempting to use the same hostname as an existing server, and then tries to register that hostname in DNS with its DHCP address. Can this potentially be disruptive to the server, or is Windows DNS smart enough to spot a duplicate hostname and deny an auto-register request from that host? What actions can be taken to ensure that DNS for a hostname cannot be altered?

  Read the article

• NetworkManager applet looks like it can't see network

  - by amorfis

  My system is Ubuntu 9.04. There is NetworkManager applet, but it looks like there are no networks. When I click it, there is disabled menu "Wired Network/device not managed". I have working eth0 interface, internet is working fine and I can see eth0 in ifconfig When I right-click and choose "Edit connections", there is only "Auto vboxnet0" under "Wired" tab. No "eth0". It shouldn't be a problem, but I cannot connect to VPN because of this :(

  Read the article

< Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >