Search Results

Search found 3676 results on 148 pages for 'dual band'.

Page 128/148 | < Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >

• Converting DisplayPort and/or HDMI to DVI-D?

  - by Jeff Atwood

  Newer Radeon video cards come with four ports standard: DVI (x2) HDMI DisplayPort If I want to run three 24" monitors, all of which are DVI only, from this video card -- is it possible to convert either the HDMI or DisplayPort to DVI? If so, how? And which one is easier/cheaper to convert? I did a little research and it looks like there isn't a simple "dongle" method. I found this DisplayPort to DVI-D Dual Link Adapter but it's $120; almost cheaper to buy a new monitor that supports HDMI or DisplayPort inputs at that point! There's also a HDMI to DVI-D adapter at Monoprice but I'm not sure it will work, either. AnandTech seems to imply that you do need the DisplayPort-to-DVI: The only catch to this specific port layout is that the card still only has enough TMDS transmitters for two ports. So you can use 2x DVI or 1x DVI + HDMI, but not 2x DVI + HDMI. For 3 DVI-derived ports, you will need an active DisplayPort-to-DVI adapter.

  Read the article

• How can I split 200Mbps of streaming traffic into routers?

  - by Jared

  As the title says, I have 200Mbps of streaming video traffic coming into my command center. How do I split the load between routers? Setup is like this: fiber --- router --- switch --- workstations I'm sorry I haven't dealt with this much traffic before. so please be gentle if you're going to kick me out :) EDITED FOR DETAILS: Okay, this specific project is for our company's IP CCTV system. We have deployed over 100++ cameras all over a building/campus and we have estimated each camera to take about 2Mbps of bandwidth each. Now, they're all connected to a switch and that's entirely fine. But coming into our command center, they have to be on a router since it'll get more than 200++ cameras next year (and I don't want to have too many hosts on one subnet). My plan was to have the 1st hundred on a 172.16.9.x block and the 2nd hundred on a 172.16.10.x block (all /24). The servers I have are currently sized to match (about 5 dual 6-core xeons) and I'd have about 19 workstations all streaming video from the 5 servers. (servers pull video from the cameras). But 200Mbps of constant traffic? How the hell do I even break this up? I need to have 1 gateway, to manage the routes... I honestly think I'm way in over my head.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Apache Process question about RAM usage

  - by Andrew Fashion

  So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

  Read the article

• Architecture for highly available MySQL with automatic failover in physically diverse locations

  - by Warner

  I have been researching high availability (HA) solutions for MySQL between data centers. For servers located in the same physical environment, I have preferred dual master with heartbeat (floating VIP) using an active passive approach. The heartbeat is over both a serial connection as well as an ethernet connection. Ultimately, my goal is to maintain this same level of availability but between data centers. I want to dynamically failover between both data centers without manual intervention and still maintain data integrity. There would be BGP on top. Web clusters in both locations, which would have the potential to route to the databases between both sides. If the Internet connection went down on site 1, clients would route through site 2, to the Web cluster, and then to the database in site 1 if the link between both sites is still up. With this scenario, due to the lack of physical link (serial) there is a more likely chance of split brain. If the WAN went down between both sites, the VIP would end up on both sites, where a variety of unpleasant scenarios could introduce desync. Another potential issue I see is difficulty scaling this infrastructure to a third data center in the future. The network layer is not a focus. The architecture is flexible at this stage. Again, my focus is a solution for maintaining data integrity as well as automatic failover with the MySQL databases. I would likely design the rest around this. Can you recommend a proven solution for MySQL HA between two physically diverse sites? Thank you for taking the time to read this. I look forward to reading your recommendations.

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• multiple ssh aliases is selecting wrong user when forwarding

  - by Chris Beck

  I'm following the dual identity procedure for bitbucket: I have 2 bitbucket accounts ccmcbeck and chrisbeck. The former is personal, the latter is work. On my local Mac, I have this in my ~/.ssh/config Host *.work.com User chris ForwardAgent yes IdentityFile ~/.ssh/work_dsa Host bitbucket-personal HostName bitbucket.org User ccmcbeck ForwardAgent no IdentityFile ~/.ssh/bitbucket_ccmcbeck_rsa Host bitbucket-work HostName bitbucket.org User chrisbeck ForwardAgent no IdentityFile ~/.ssh/bitbucket_chrisbeck_rsa On my local Mac I ssh -T all is good, I get: $ ssh -T git@bitbucket-personal logged in as ccmcbeck. $ ssh -T git@bitbucket-work logged in as chrisbeck. On my local Mac, the ssh version is OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 When I ssh foo.work.com to my Linux box, I get: $ ssh-add -l 1024 ... /Users/chris/.ssh/work_dsa (DSA) 2048 ... /Users/chris/.ssh/bitbucket_ccmcbeck_rsa (RSA) 2048 ... /Users/chris/.ssh/bitbucket_chrisbeck_rsa (RSA) On foo.work.com, I also have this in my ~/.ssh/config Host bitbucket-personal HostName bitbucket.org User ccmcbeck ForwardAgent no IdentityFile ~/.ssh/bitbucket_ccmcbeck_rsa Host bitbucket-work HostName bitbucket.org User chrisbeck ForwardAgent no IdentityFile ~/.ssh/bitbucket_chrisbeck_rsa However, on foo.work.com when I ssh -T, it references the wrong User for git@bitbucket-work $ ssh -T git@bitbucket-personal logged in as ccmcbeck. $ ssh -T git@bitbucket-work logged in as ccmcbeck. On foo.work.com, the ssh version is OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 Why is my configuration causing foo.work.com to reference the wrong User?

  Read the article

• JVM system time runs faster than HP UNIX OS system time

  - by winston

  Hello I have the following output from a simple debug jsp: Weblogic Startup Since: Friday, October 19, 2012, 08:36:12 AM Database Current Time: Wednesday, December 12, 2012, 11:43:44 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:45:38 AM Line 1 was a recorded variable during WebLogic webapp startup. Line 2 was output from database query select sysdate from dual; Line 3 was output from java code new Date() I have checked from shell date command that line 2 output conforms with OS time. The output of line 3 was mysterious. I don't know how it comes from Java VM. On another machine with same setting, the same jsp output like this: Weblogic Startup Since: Tuesday, December 11, 2012, 02:29:06 PM Database Current Time: Wednesday, December 12, 2012, 11:51:48 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:51:50 AM Another machine: Weblogic Startup Since: Monday, December 10, 2012, 05:00:34 PM Database Current Time: Wednesday, December 12, 2012, 11:52:03 AM Weblogic JVM Current Time: Wednesday, December 12, 2012, 11:52:07 AM Findings: the pattern shows that the longer Weblogic startup, the larger the discrepancy of OS time with JVM time. Anybody could help on HP JVM? On HP UNIX, NTP was done daily. Anyway here comes the server versions: HP-UX machinex B.11.31 U ia64 2426956366 unlimited-user license java version "1.6.0.04" Java(TM) SE Runtime Environment (build 1.6.0.04-jinteg_28_apr_2009_04_46-b00) Java HotSpot(TM) Server VM (build 11.3-b02-jre1.6.0.04-rc2, mixed mode) WebLogic Server Version: 10.3.2.0 Java properties java.runtime.name=Java(TM) SE Runtime Environment java.runtime.version=1.6.0.04-jinteg_28_apr_2009_04_46-b00 java.vendor=Hewlett-Packard Co. java.vendor.url=http\://www.hp.com/go/Java java.version=1.6.0.04 java.vm.name=Java HotSpot(TM) 64-Bit Server VM java.vm.info=mixed mode java.vm.specification.vendor=Sun Microsystems Inc. java.vm.vendor="Hewlett-Packard Company" sun.arch.data.model=64 sun.cpu.endian=big sun.cpu.isalist=ia64r0 sun.io.unicode.encoding=UnicodeBig sun.java.launcher=SUN_STANDARD sun.jnu.encoding=8859_1 sun.management.compiler=HotSpot 64-Bit Server Compiler sun.os.patch.level=unknown os.name=HP-UX os.version=B.11.31

  Read the article

• Somewhat powerful server needed for computationally expensive stuff

  - by Dane Larsen

  So here's my problem. My Dad runs a company that does some rather computationally expensive stuff. This is not supercomputer level stuff, but it does take several hours to run the average job on his Core i7 desktop. He asked me to look into a way to have his customers use the code on an hourly basis, namely via a server. Ideally he'd be able to buy a box for about $1000, and hook it right up to our home connection. Unfortunately, the data that needs to be both sent and received is on the order of several hundred megs. We live in a rural area, and the fastest connection offered is 1.5Mbit/s. Download. It's like .3Mbit/s upload. Not workable. What are the options for this kind of thing? Ideally, we'd have about 2GB of ram, 300-500GB of storage, and a nice dual core, and it has to run some flavor of Linux. Any suggestions? Thanks in advance EDIT: Also, ideally the monthly price would be < $100 per month.

  Read the article

• Internet doesn't work when enable local Lan

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• Formatted C: from Windows 7 setup, now it won't even install

  - by ocurro

  Help, I'm so confused. I did more or less what's been described here: I formatted Vista and installed Windows 7 over it. Problem is that I'm now unable to boot (...) [1] I'm installing Seven on top of Vista on ACER AS1410 Notebook When it comes to the part where I choose where to install, I pick the partition labeled C: but instead of keeping windows.old files (what would I want them for?) I choose to go and carelessly format the partition (my bad). It shows me this error: Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information Now the only option is "Load Driver". i have tried installing every single one from ACER website, none of them are useful. I even flashed orig. BIOS. I've tried going back and choose "Repair" like in the picture:[2] but I only get an error: "Failed to save startup options" I think this is weird, what else can I do? [1] superuser.com/questions/117076/formatting-of-an-xp-vista-dual-boot-machine-now-unable-to-boot-up-xp [2] www.howtogeek.com/wp-content/uploads/2007/08/image51.png

  Read the article

• GA 8KNXP Rev1.0: 4 GB installed, only 3.5 GB recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4 GB. The specification from the manual says: Maximum memory support: 4 GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my Linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in Linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• LG W3000H-BN monitor cannot go above 1280x800

  - by Jo Profit

  I noticed that there are many people complaining about this issue with the W3000H but I have yet to find a solution that works for me. I am using Windows 7 Professional and and using a nVidia Quadro NVS 240 video card with a 4 monitor splitter cable. The cable from the monitor and the splitter are rated DVI-D Dual Link and the video card itself is rated for 2560x1600. I have installed the latest drivers for the video card and just grabbed the .inf, icm and cat file from the LG website and manually installed the monitor drivers. Does anyone have problems with the same setup? I have 3 other monitors (2 at 1920x1080 and 1 at 1280x1024). I really would like to be able to display the full resolution or else the large screen is useless. (I triple checked that the monitor itself supports this resolution). So monitor, cable, splitter and card supposedly support 2560x1600. Drivers are up to date but I cannot select that resolution when in the "Screen Resolution" menu, nor through the nVidia control panel. Please save me from madness :)

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• NVIDIA GeForce GT750M drivers for Ubuntu 13.10 on iMac

  - by Eugene B

  I have just got a new iMac 14.3 with 21.5' display. It has Intel i7 processor and NVIDIA GeForce GT750M graphics card with GPU (Device ID: 0x00fe9). I have installed Ubuntu 13.10 on it (dual boot with refit). Everything works fine apart from graphics. It is clear that graphics' not accelerated, and there are no drivers suggested in the "Additional drivers" section. I have tried to Install nvidia drivers from the repository. Download nvidia drivers and install them manually. Follow instructions here. Follow instructions here. Follow instructions here. Install bumblebee. Play around with xorg.conf file. Blacklist nouveau. As you may guess, nothing worked. The weirdest thing is, that when I boot from a LiveCD, it picks up screen resolution and all the rest correctly, though when I install the system to my Hard Drive it clearly does not have proper drivers. Does anyone have any suggestion what to do?

  Read the article

• Best way to attach 96 tb to workstation

  - by user994179

  I'm running a workstation with dual xeon 5690's (12 physical/24 logical cores), 192 gb of ram (ie, maxed-out), Windows 7 64bit, 5 slots for adapter cards, and 1 tb of internal storage, with 5 more internal bays available. I have an app that creates data files totaling about 88 tbs. These are written once every 14 months, and the rest of the time the app only needs to read them; and 95% of the reads are sequential reads of huge chunks of data. I have some control over how big the individual files are, but ideally they would be between 5 and 8 tbs. The app will be reading from only one drive at a time, and the nature of the data is such that if (when) a drive dies I can restore the data to a new disk from tape. While it would be nice to be able to use the fastest drive/controllers available, at this point size matters more than speed. After doing lots of reading, I am leaning toward buying a bunch of cheap 2tb drives and putting them into a bunch of cheap enclosures. All this stuff is going into my home office, so I need to avoid the raised floor/refrigerated approach. My questions: Is the cheap drive/enclosure solution the best one for this situation? Given the nature of the app and the way the data is used, does RAID make sense? If so, which one? For huge sequential reads, would Usb 3.0 and eSata be a wash performance-wise? For each slot available on the workstation, can I hook up an enclosure that can hold multiple drives? Or is it one controller per drive? If I can have multiple drives on one controller, am I essentially splitting the bandwidth (throughput)? For example, if I have a 12 bay enclosure, is the throughput of the controller reduced by a factor of 12? Are there any Windows 7 volume/drive/capacity limits I should be aware of? Thanks

  Read the article

• How do I calculate clock speed in multi-core processors?

  - by NReilingh

  Is it correct to say, for example, that a processor with four cores each running at 3GHz is in fact a processor running at 12GHz? I once got into a "Mac vs. PC" argument (which by the way is NOT the focus of this topic... that was back in middle school) with an acquaintance who insisted that Macs were only being advertised as 1Ghz machines because they were dual-processor G4s each running at 500MHz. At the time I knew this to be hogwash for reasons I think are apparent to most people, but I just saw a comment on this website to the effect of "6 cores x 0.2GHz = 1.2Ghz" and that got me thinking again about whether there's a real answer to this. So, this is a more-or-less philosophical/deep technical question about the semantics of clock speed calculation. I see two possibilities: Each core is in fact doing x calculations per second, thus the total number of calculations is x(cores). Clock speed is rather a count of the number of cycles the processor goes through in the space of a second, so as long as all cores are running at the same speed, the speed of each clock cycle stays the same no matter how many cores exist. In other words, Hz = (core1Hz+core2Hz+...)/cores.

  Read the article

• Asus MyCinema U3100mini Choppy

  - by dsimcha

  I'm running an Asus MyCinema U3100mini ATSC on Windows 7 64-bit. When I play live TV in Windows Media Center, it's very choppy and uses 500+ MB of RAM, I'm guessing due to the hard drive buffering functionality. Is there any way to disable the live TV pause buffer completely? If not, can anyone recommend alternative software that: Works with the MyCinema. Is lightweight and not horribly bloated with features I'll never use like Windows Media Center is. Edits: This is a dual boot system. I've discovered that the tuner actually works fine on XP. It also works fine on my other computer, which has slower hardware and also runs Windows 7 64-bit. The problem actually seems to be with playback at large screen sizes, not with hard drive buffering. Everything works fine below a certain window size and fails for large windows or full screens. Also, the same thing seems to happen whether playing live or recorded TV. As far as the obvious stuff goes, I have the latest video drivers from ATI for my Radeon x1050.

  Read the article

• 10Gbe sfp+ Cross Over Cable required? Is there such a thing?

  - by dc-patos

  To preface, this is my first experience with 10GBe networking and I have encountered an issue which research does not seem to document a solution for... I have two servers (older DL580G5 and DL380G5), each with a HP NC522SFP 10Gbe dual sfp+ port adapter. I have purchased copper "passive" direct connect adapter cables (which look like twinax), which seem to work well when I connect them to the sfp+ ports on my Dell 5524 switch. However, if I directly connect the two servers with the same cable, the link doesn't come up. I am running WS2012 standard on each server. My intention is to use one of these servers as a home brew SAN and I would like to enable mutiple 10Gbe paths for iSCSI traffic. My question(s): Can I connect the two adapters to each other, such as I would with other less speedy generations of ethernet? If I can, do I require a crossover cable, or some type of other sfp+ cable solution to do this? My 10Gbe sfp+ switch ports are premium, but server to server connections are doable in small numbers for me and I would really like the multiple paths this would give me. Is there a simple solution?

  Read the article

• vmware vmdk disk problem

  - by dmtr

  Hello, I have a vmware esxi 4 server and 2 storage servers (mount as nfs). Between the storage servers (fedora 14) is made drbd cluster (dual primary) and ocfs2 filesystem, also every server has local partition with ext4 filesystem, both are mounted as nfs on esxi server. When i tried to copy a virtual machine (naturally it power off) files from ext4 partition to ocfs2 partition, vmdk total file size is different, but md5sum is the same. on ext4 partition: # ls -la total 28492228 -rw------- 1 root root 42949672960 Jan 14 14:46 disk-flat.vmdk # md5sum disk-flat.vmdk 0eaebe3138beb32f54ea5de6dfe5a987 on ocfs2 partition: # ls -la total 13974660 -rw------- 1 root root 42949672960 Jan 14 16:16 disk-flat.vmdk # md5sum disk-flat.vmdk 0eaebe3138beb32f54ea5de6dfe5a987 When i power on the virtual machine from ocfs2 partition it dosn't work. I have a windows on the virtual machine and it freez?s after windows logo. From ext4 partition the virtual machine is worked. Test with linux (create and install on ext4 partition and copy) the same problem appears. When i create a virtual machine directly from ocfs2 partition, there are no problems. I tried to copy via vSphere client, and i have the same problem. Any suggestions ?

  Read the article

• Tri-head linux system with Xmonad: is it possible to have HW acceleration

  - by progo

  What means there exists to have three monitors, all controlled by Xmonad and have hardware 3D acceleration as well? I had the pleasure of using three monitors earlier this year, and while Xmonad and Xinerama handle three monitors easily, I had to throw in an extra display driver, and also let go of Nvidia's own TwinView (which is a hack on Xinerama). This left me with no HW acceleration and some flickering as double buffering wouldn't work with certain applications. However, the three monitors handle so beautifully that I had hard time coming back to two. I understand the easiest way to achieve HW-accelerated tri-head combo is to split into two Xorgs. I wouldn't be able to switch windows between the Xorgs, so I'm not really into this solution. What's more, having a cheap and old PCI card along with even slightly better PCIe seemed to slow things down. Even if I occasionally disabled the third monitor from Xorg configure, I couldn't get HW acceleration to work. Only after I physically disconnected the old PCI card, I could get the games back in business. Would a Matrox Dual/Tri-head2go and a powerful Nvidia GPU do the trick? I understand Xmonad can be configured to "believe" that a "single" (as Dualhead2Go will merge) 3360x1050 display is actually two different ones? So that Xmonad's Mod-w and Mod-e would work properly there.

  Read the article

• Cross OS data recover question, USB drive involved.

  - by Moshe

  Here's the story: A MacBook had OS X 10.4 and Windows XP dual booting using rEFIt. Then the Windows partition gets corrupted and it won't boot. Presumably a virus. There were sensitive files there and those were successfully copied to a USB drive and then 10.5 was installed on the hard drive, formatting the drive in the process. The USB drive's contacts cracked and he data is lost from there, unless it can be resoldered. The issues is that there is too much solder there already. So, how can the data in question be recovered? The files were Microsoft Money (not the latest version) files for the Windows version of the program. Right now, only OS X is installed on the MacBook. Is there Mac based program that can recover the Windows data or am I better off trying to resolder the drive? Does anyone know how to best resolder a USB drive more than once, where the first solder is ther, but detached from the silicon? Also, what format (extension) are Microsoft Money files? In need of help!

  Read the article

• hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

  - by user450688

  Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

  Read the article

• Cannot install CentOS 6.5 using UEFI usb boot

  - by Vaindil

  I am trying to dual-boot CentOS 6.5 on my desktop that is currently running Windows 8.1. I have two storage devices: an SSD that has my Windows installation, and an HDD that has all of my data. Both are formatted using GPT, and Windows boots using UEFI. I used the CentOS 6.5 live DVD (CentOS-6.5-x86_64-LiveDVD.iso) to create an EFI-bootable flash drive (it does boot properly in EFI mode). I receive an error, however, when CentOS is booting (error is below). I have a 6.4 boot DVD which boots as expected, but it does not boot in UEFI mode and therefore doesn't play nicely with my Windows installation (I have no way to access it, even using rEFInd or any other similar tools). What do I need to do to get the device to boot properly in UEFI mode? Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init Not tainted 2.6.32-431.el6.x86_64 #1 Call Trace: [<ffffffff815271fa>] ? panic+0xa7/0x16f [<ffffffff81077622>] ? do_exit+0x862/0x870 [<ffffffff8118a865>] ? fput+0x25/0x30 [<ffffffff81077688>] ? do_group_exit+0x58/0xd0 [<ffffffff81077717>] ? sys_exit_group+0x17/0x20 [<ffffffff8100b072>] ? system_call_fastpath+0x16/0x1b drm_kms_helper: panic occurred, switching back to text console

  Read the article

• Are These Parts compatible?

  - by ell

  I have never assembled a PC before, although I have taken an old one apart and replaced a few parts in others here and there so I have (very) limited experience. I have been looking to make a pc and here are the parts I might buy: Foxconn P45AL Intel P45 (Socket 775) DDR2 Motherboard (with onboard sound I believe) Gigabyte GeForce GTX 460 OC 768MB GDDR5 PCI-Express Graphics Card Already have 2 1gb sticks of dual channel DDR2 memory Intel Core 2 Quad Q8400 LGA775 'Yorkfield' 2.66GHz 4MB-cache Processor Samsung SpinPoint F3 1TB SATA-II 32MB Cache Hard Drive Antec Dark Fleet Series DF10 Gaming Enclosure – Black I already have monitor, mouse, keyboard and DVD/CD drive Akasa Freedom Power 1000W Modular Power Supply I have never done this before so feel free to laugh at me for getting something obvious wrong, forgetting a vital component etc. but is all of this compatible? And have I gone overkill on the PSU, if so, please recommend one. Thanks in advance, ell. EDIT: Added PSU which I forgot to mention EDIT: I would be using this to surf the internet, write e-mails, chat, word process, play games such as team fortress 2 & spring rts (at highest graphics hopefully), some 3d modelling in blender, some opengl programming, and image editing in GIMP.

  Read the article

< Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >