Search Results

Search found 13104 results on 525 pages for 'non blocking'.

Page 128/525 | < Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >

• Why is Server 2012 assigning "169.254.*.*" series when creating DHCP server?

  - by Seth

  I have a small office, with ATT Motorola modem (192.168.1.254) set as passthrough to Dlink DIR-815 (LAN 192.168.0.1) I am trying to setup DHCP server on Server 2012, and when I create new DHCP server, the title is created as 169.254.. instead of the domain name. (Domain clients can retrieve IP's as defined in the scope) Non-domain clients are not receiving IP's from the server but rather the Motorola... How do I assure DHCP setup is properly creating itself, and how do I make sure domain and non-domain clients get IP's from the server?

  Read the article

• How would I isolate one networked PC to LAN only?

  - by itsraine

  I would like to have one of my PCs available to the rest of my home network for file sharing and VNC access, but I want to block any Internet traffic going to and from the PC. In other words, I want all local PCs I have connected to the router functioning as any normal LAN would, but when it comes to the Internet I want one particular PC to be "safe" from the Internet. My guess is that this is some sort of port blocking or some other router function, but I'm not quite sure.

  Read the article

• How to elegantly selectively exclude FreeBSD network traffic from OpenVPN interface by port

  - by Polygonica

  inexperienced sysadmin here. I'm planning on running a net daemon inside a FreeBSD jail through OpenVPN, but want to be able to SSH directly into the jail and use the daemon's web interface daemon without going through the VPN. As I understand it, an OpenVPN tunnel is normally set up as a default virtual internet interface, and so incoming traffic will go out on the OpenVPN interface by default (which is problematic, as this incurs latency). I thought "well, obviously, since all of this traffic is leaving on a handful of ports, I'll just redirect those to the non-VPN gateway." I've tried to look for solutions, but almost all of them involve iptables instead of ipfw (which is default for FreeBSD) and solve slightly different problems. And alternate solutions like using multiple default routes to ensure that incoming traffic on any interface is always sent out on the same interface seem far-reaching and require deep knowledge of all tools involved. Is there an elegant way of ensuring that traffic leaving on specific ports exits on a specified non-default interface using ipfw?

  Read the article

• Firewall - Preventing Content Theft & Rogue Crawlers

  - by drodecker

  Our websites are being crawled by content thieves on a regular basis. We obviously want to let through the nice bots and legitimate user activity, but block questionable activity. We have tried IP blocking at our firewall, but this becomes to manage the block lists. Also, we have used IIS-handlers, however that complicates our web applications. Is anyone familiar with network appliances, firewalls or application services (say for IIS) that can reduce or eliminate the content scrapers?

  Read the article

• Does netqmail-1.06 already include badmailfrom wildcard?

  - by user16081

  thinking about blocking all '.info' domains on a server running netqmail-1.06 I saw the instructions for the badmailfrom-wildcard patch http://tomclegg.net/qmail-bmf-wildcard specifically mention qmail-1.03 and make no mention of netqmail-1.06. I searched around to see if this patch is already included but didn't find any information in the netqmail changelog http://www.qmail.org/netqmail/CHANGES or anywhere Tried using it by putting '.info' into the badmailfrom file and restarted qmail without error, it seems to be working. Can anyone confirm that this functionality is included in netqmail-1.06?

  Read the article

• iptables: Allow only HTTP access for web browsing

  - by user1448260

  Have a linux box, want it locked down but just be able to surf internet on it. Why is this script blocking http too? #!/bin/sh # # iptables -F # #Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT DROP # # Allow TCP connections on tcp port 80 # iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # List rules # iptables -L -v

  Read the article

• rsync to ONLY keep files in destination that have been removed from source

  - by David Corley

  We use rsync to copy filesystem contents from one machine to another as a backup. We first run MACHINE-X-MACHINE-Y rsync for a straight backup with the --delete and --delete-excluded switches We also run an internal Rsync between the MACHINE-Y destination, and another folder on MACHINE-Y with either of the delete flags. This maintains a non-destructive copy in the event someone inadvertently deletes a file on MACHINE-X. However, it also has the overhead of being a complete copy of what has already been synchronized. Ideally I want to be able to run the non-destructive rsync in such a way that the destination ONLY receives the deleted files and so avoids unnecessary duplication . Is there any way to do this?

  Read the article

• postgresql login from remote

  - by Hellnar

  I want to give remote access to my postresql db (8.2) to computers that are at the same lan, at the default config I have added this line to pg_hba.conf where xxx.xx.xx.xx is the ip of the machine that hosts postgresql. This machine is a windows 2k server. # IPv4 local connections: host all all 0.0.0.0/0 password host all all xxx.xx.xx.xx/24 password There no firewall or such blocking the connection between and `listen_addresses = '*' for postgresql.conf .

  Read the article

• How do I tell if a Python pip install is working correctly or hanging?

  - by wobbily_col

  I am trying to install the python pandas package in a virtualenv using pip. On my development machine it installed correctly, but now I am trying on the server, it gets so far then it seems to get stuck: warnings.warn(LapackSrcNotFoundError.__doc__) /apps/PYTHON/2.7.3/lib/python2.7/distutils/dist.py:267: UserWarning: Unknown distribution option: 'define_macros' warnings.warn(msg) non-existing path in 'numpy/distutils': 'site.cfg' non-existing path in 'numpy/lib': 'benchmarks' Could not locate executable gfortran Could not locate executable f95 Found executable /apps/modules/wrappers/fortran/ifort Top shows ifort running at 46% cpu. Is there any way I can tell if this is working correctly (can I check files it is updating for example), or if it is stuck in a loop? It has been running for 40 minutes so far.

  Read the article

• Connecting to a remote mysql server from a windows machine (XP)

  - by Samuel Martin

  I am trying to connect to mysql server which is installed on my home pc from another pc. I allowed all connection in mysql configuration. There's no firewall blocking on the pc I am trying to connect from. I used the command- mysql -h Some.Host.IP -u SomeUser -p SomePassword I am getting- ERROR 2003 (HY000): Can't connect to MySQL server on 'Some.Host.IP' (10060) I can connect through php!! What's the problem? How do I solve it?

  Read the article

• Windows 7 Homegroup with ess 4.0

  - by Noam Gal

  I am trying to setup a homegroup between two win7 computers, and apparently my Eset Security Service is blocking the traffic. When I disable the firewall on both computers the homegroup works fine. Is there a known fix/workaround for it?

  Read the article

• Does installing windows format the hard disk?

  - by Jason

  My Google search for ""does installing windows format the hard disk" returns: No results found for "does installing windows format the hard disk". I was quite surprised. I'm hoping to get a quick answer here. Does an install format the hard disk, and destroy all data, including non-os/s data? -Or do you specifically have to say "format" at some point so you know you are losing everything? [I tried to go to SP3, but it doesn't work on my computer. My SP2 disk is fired. I only have a SP1 disk, with a seperate SP2 package. I can't get to Safe Mode to uninstall SP3 ("Windows XP Setup cann run under Safemode. Setup will restart now.). I don't want running the SP1 disk to destroy any non-o/s data.] Thanks.

  Read the article

• Rpm removal does not remove delivered dirs and leaves garbage

  - by Jim

  I deliver an application via an RPM. This application delivers various directories and files. E.g. under /opt/internal/com a file structure is being copied. I was expecting that on rpm -e all the file structure delivered under /opt/internal/com will be removed. But it does not. There are directories in the file structure that are non-empty. Is this the reason? But these (non-empty) directories were created by the RPM installation. So I would expect that they would be "owned" by RPM and removed automatically. Is this wrong? Am I supposed to remove them manually?

  Read the article

• Running RAID on an internal storage drive

  - by Johnny W

  I am running Windows 8 on an SSD, and it's all running swimmingly, but I want to put my documents on a "normal" HD running under RAID 1. I have four SATA 3GB/s ports on my motherboard (my Windows 8 SSD drive in on a different 6GB/s controller). All four are used (1 Bluray Optical Drive, 1 Spare HD, and the 2 I wish to turn into a RAID 1 drive. In my BIOS I can only change settings for the entire controller, not just ports. So my question is: If I turn these four ports into a RAID controller, will that negatively affect the non-RAID hardware plugged into it? I.e. Will a HD or Bluray drive be slower/incompatible with being plugged into a non AHCI SATA port? Thanks.

  Read the article

• Securing debain with fail2ban or iptables

  - by Jimmy

  I'm looking to secure my server. Initially my first thought was to use iptables but then I also learnt about Fail2ban. I understand that Fail2ban is based on iptables, but it has the advantages of being able to ban IP's after a number of attempts. Let's say I want to block FTP completely: Should I write a separate IPtable rule to block FTP, and use Fail2ban just for SSH Or instead simply put all rules, even the FTP blocking rule within the Fail2Ban config Any help on this would be appreciated. James

  Read the article

• When HDD wakes up?

  - by NumberFour

  Im looking for some small script or application which could log the time when a non-system disk wakes up. I cannot identify which application or script wakes up my non-system drive (which has to be asleep until I work with it). I have already set the noatime flag, tried to use powertop and iotop to determine which application could prevent it from going to sleep - but with no result. So my plan is to set this drive asleep (hdparm -Y) and see at what time it gets regularly woken up. Thanks for any advice.

  Read the article

• Starting VMs with an executable with as low overhead as possible

  - by Robert Koritnik

  Is there a solution to create a virtual machine and start it by having an executable file, that will start the machine? If possible to start as quickly as possible. Strange situation? Not at all. Read on... Real life scenario Since we can't have domain controller on a non-server OS it would be nice to have domain controller in an as thin as possible machine (possibly Samba or similar because we'd like to make it startup as quickly as possible - in a matter of a few seconds) packed in a single executable. We could then configure our non-server OS to run the executable when it starts and before user logs in. This would make it possible to login into a domain.

  Read the article

• Getting console2 to work nicely with UAC

  - by Merlyn Morgan-Graham

  I would like to get console2 to work nicely with UAC Particular problems I would like to tackle: If I start non-elevated, have a way to elevate while running. It'd be especially nice if I could elevate individual tabs I would like to get different coloring for admin/non-admin, similar to: this link. Basically, if I can get the console to execute a command on startup (similar to the HKLM\Software\Microsoft\Command Processor\AutoRun registry value), that's all I need How do I get this working? Would I have to modify source code to get this to work, or can I use different tab settings/do hacks w/ shell executables? I am using Windows 7, although I would imagine any working solution would also work on Vista.

  Read the article

• How to block this URL pattern in Varnish VCL?

  - by iTech

  My website is getting badly hit by spambots and scrappers, I am using Cloudflare but the problem still remains there. The problem is spambots accessing non-existing urls causing a lot of load to my drupal backend which goes all the way and bootstraps db just to serve a 404 error doc. I cant simply dish out non-drupal 404's for all page not found errors, as I need to have drupal catch them. Since, varnish is in front it can check if the bot is acting nice and asking for valid url - if not it servers them a 404 or 403. These bots are causing errors using this pattern : http://www.megaleecher.net/http:/www.megaleecher.net/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_S/Using_iPhone_As_USB_Mass_Storage Now, pls. suggest a regex varnbisg VCL directive which catches this URL pattern and serves a 404 error from varnish, preventing it from reaching apache/drupal ?

  Read the article

• Directory "Bookmarking" in Linux

  - by Jason R. Mick

  Aside from aliasing and links, is there an easy way in Linux to tag commonly used directories and to navigate to a commonly used directory from the terminal. To be clear the disadvantages I see with alternative approaches, and why I want a bookmark/favorites like system: alias Cons: Too specific (every new favorite requires a new alias...although you could in theory make an alias that echo append your dir as a new alias, which would be sort of clever). Can't nest favorites in folders (can't think of a simple solution to this outside of heavy config scripting). links Cons: Clutter directory make ls a headache. pushd/popd Cons: Non-permanent (without shell config file scripting), can't nest favorites in directories, etc. Granted I have multiple ideas for making my own non-standard solution, but before I have at it I wanted to get some perspective on what's out there and if there is nothing, what is a recommended approach. Does anyone know of such a favorites/bookmark-like terminal solution?

  Read the article

• Per-character-set font size in Firefox not working?

  - by Coderer

  Firefox has a setting (Preferences - Content - Fonts & Colors - Advanced) that is supposed to let you set font preferences for different character sets. I've tried setting larger minimum font sizes for some non-Western character sets (I'm still learning, and have to see extra detail to tell them apart!) and nothing seems to happen. For example, if there's Hangul on a page (like this one), it will show in the same size as the Latin characters around it, even if I set "minimum font size" to 24. Am I misunderstanding how that setting is supposed to work, or does it just not do anything? Is there any other way to blow up only non-Western characters while leaving the letters I know how to read intact?

  Read the article

• DNS Update 'stuck'

  - by Postus

  I have a dedicated server with Debian and ISPconfig on it And a domain example.it I did a error while setting the dns for the first time I've tried to set it to ns1.example.it IP.IP.IP.IP myDedicnumber.kimsufi.com IP.IP.IP.IP But it got stuck it shows "Current Status: on hold" its been 7days already. I've tried contacting ovh but they just told me to set my dns to something diffrent but I can't as this operation is blocking any changes to the DNS records. Is there anything that I could do accept bug OVH?

  Read the article

• When should I upgrade to Ubuntu 10.04 (Lucid Lynx)? [closed]

  - by Emyr

  I'm a web developer for a small non-IT firm. When 9.10 came out, I was using it with no adverse effects from about a month before release (iirc, first beta), initially as an upgrade but as a clean install later to ensure my system would be consistent with most other 9.10 systems. The last alpha of 10.04 came out last week, with another 2 weeks before beta. I'm quite eager to do it today, but obviously the usual "not for production systems" notice is still in place. When should I upgrade? Do I need to worry about software installed from source? (./configure, make, make install etc) Is the attraction of a non-brown theme really this tempting for you?

  Read the article

• Run Photoshop on VM (virtual machine) to increase calculation power, without violating the licence agreement (EULA)

  - by mecplusultra

  A question concerning the possibility to run Photoshop as VM without violating the licence agreement (EULA) : My Adobe Photoshop is bloody slow, nd sometimes I need to launch thousands of image calculations that have to use hundreds of PSD templates. I want to increase my Photoshop calculation power by creating non-persistent virtual machines on my hosted server. Each VMm would only alive for a few seconds, just enough time to deliver the calculated file. Is this a violation of the EULA? I must clarify that I'm the only one to access my non persistent VMs.

  Read the article

• Starting VM as an executable with as low overhead as possible

  - by Robert Koritnik

  Is there a solution to create a virtual machine and start it by having an executable file, that will start the machine? If possible to start as quickly as possible. Strange situation? Not at all. Read on... Real life scenario Since we can't have domain controller on a non-server OS it would be nice to have domain controller in an as thin as possible machine (possibly Samba or similar because we'd like to make it startup as quickly as possible - in a matter of a few seconds) packed in a single executable. We could then configure our non-server OS to run the executable when it starts and before user logs in. This would make it possible to login into a domain.

  Read the article

< Previous Page | 124 125 126 127 128 129 130 131 132 133 134 135  | Next Page >