Search Results

Search found 4458 results on 179 pages for 'cd'.

Page 129/179 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

  • How do I get a Broadcom BCM4311 working?

    - by Fer1805
    I'm having serious problems installing the broadcom drivers for ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. Broadcom BCM4311 Wireless not working Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

  • Installing e text editor

    - by kristian nissen
    I am trying to get e-text editor to run. I read http://www.e-texteditor.com/forum/viewtopic.php?p=14953#14953 and Compile e-text editor on Linux as well. But on my 10.04 Lucid it fails at the following step: ./build_externals_linux.sh debug with the following error messages: Building debug binaries Building 32-bit binaries Going to place output in /opt/etexteditor/external/out.debug ./build_externals_linux.sh: line 41: pushd: bakefile: No such file or directory ./build_externals_linux.sh: line 42: ./configure: No such file or directory Cannot compile bakefile ./build_externals_linux.sh: line 46: popd: directory stack empty ./build_externals_linux.sh: line 49: pushd: metakit: No such file or directory ./build_externals_linux.sh: line 50: cd: builds: No such file or directory Cannot compile MetaKit ./build_externals_linux.sh: line 56: popd: directory stack empty ./build_externals_linux.sh: line 59: pushd: pcre: No such file or directory ./build_externals_linux.sh: line 60: ./configure: No such file or directory Cannot compile pcre ./build_externals_linux.sh: line 66: popd: directory stack empty ./build_externals_linux.sh: line 69: pushd: tinyxml: No such file or directory make: *** No rule to make target `clean'. Stop. cannot compile TinyXML ./build_externals_linux.sh: line 77: popd: directory stack empty ./build_externals_linux.sh: line 80: pushd: libtommath: No such file or directory make: *** No rule to make target `clean'. Stop. Cannot compile LTM ./build_externals_linux.sh: line 85: popd: directory stack empty ./build_externals_linux.sh: line 88: pushd: libtomcrypt: No such file or directory make: *** No rule to make target `clean'. Stop. Cannot compile LTC ./build_externals_linux.sh: line 93: popd: directory stack empty ./build_externals_linux.sh: line 96: pushd: wxwidgets: No such file or directory ./build_externals_linux.sh: line 97: ./configure: No such file or directory Cannot compile wxWidgets ./build_externals_linux.sh: line 104: popd: directory stack empty ./build_externals_linux.sh: line 107: pushd: webkit: No such file or directory make: *** No rule to make target `clean'. Stop. ./build_externals_linux.sh: line 109: ./WebKitTools/Scripts/build-webkit: No such file or directory Cannot compile WebKit ./build_externals_linux.sh: line 113: popd: directory stack empty what am I missing?

    Read the article

  • Ubuntu installation on iMac

    - by Shanew
    I have an iMac configured as follows - Screen 27" CPU 3.4 GHz i7 Graphics AMD Radeon HD 6970 1024 MB I downloaded Ubuntu version 11.10 64 bit ISO and burnt that to both DVD and USB stick as per the instructions on Ubuntu's download page. Neither will boot. Symptoms are as follows - DVD: When the iMac is restarted and booted from DVD (labelled Windows which isn't mentioned in Ubuntu's website instructions) one line is displayed against a black screen displaying a message about the developer and date. After 5 minutes the message hangs and the DVD ceases to spin. USB Stick: Strangely I have to select the EFI boot CD icon which appears after holding down the Alt key. A text menu appears offering me to try Ubuntu without installing. I select this and the screen goes blank and stays blank. Any ideas? Lastly, after writing Ubuntu to DVD and USB stick, neither could be read by OSX making the instructions to eject them as per Ubuntu website's instructions useless. This might help? Thanks, Shane.

    Read the article

  • Ubuntu...I love you, I hate you

    - by gregarobinson
     I have been working on seeing if a .NET 3.5 application will port over to Linux, Ubuntu to be specific. I started with version 9.01, then 9.10 and now 10.04 as I find more and more that I need from Mono. I have a dual boot on a dev box, Windows 7 and Ubuntu. An upgrade from Ubuntu 9.01 to 9.10 caused my mouse and keyboard to lock up. I was able to boot from a 9.10 cd. Then, I upgraded to 10.04 as I needed Mono 2,2. Upgrade worked, lost my windows boot though. it seems grub somehow jumped in and messed up the windows boot. After Googlign liek crazy and trying this and that, these 2 links finally got me my windows boot back:http://sourceforge.net/apps/mediawiki/bootinfoscript/index.php?title=Boot_Problems:Boot_Sector http://support.microsoft.com/kb/927392So, I am now thinking about trying SuSe instead as I hear\read it's more stable. I think a lot of my pains have been related to learning and getting use to Linux.        

    Read the article

  • help installing some java and flash

    - by william
    ok so i have git now and some other stuff but ive looked around and all and i dont get very help full info Instructions 1 Download the latest version of Flash Player from the Adobe Website. Click on "Download the Latest Player," and choose ".deb for Ubuntu" from the drop down list. 2 Choose "Save File" from the pop up window. Sponsored Links Google Cloud Hosting Build And Run Your App Using Google App Engine cloud.google.com/appengine 3 Open a terminal window. The terminal window will be found under Applications - Utilities. 4 Change to the directory where your downloaded file was saved. cd Download 5 Install the libcurl3 library. sudo apt-get install libcurl3 6 Install the Flash Player. sudo dpkg --install install_flash_player__linux.deb Replace with the latest version number. 7 Restart Firefox. 8 Check that Flash Player was installed. Type about:plugins in a browser window, and look for the flash player MIME type. Read more: http://www.ehow.com/how_5068467_install-flash-player-ubuntu.html#ixzz2ixPj47qS what i dont is how the heck i change the directory and all that crap witch they say every one know

    Read the article

  • CodePlex Daily Summary for Friday, November 09, 2012

    CodePlex Daily Summary for Friday, November 09, 2012Popular ReleasesPlayer Framework by Microsoft: Player Framework for Windows 8 (v1.0): IMPORTANT: List of breaking changes from preview 7 Ability to move control panel or individual elements outside media player. more info... New Entertainment app theme for out of the box support for Windows 8 Entertainment app guidelines. more info... VSIX reference names shortened. Allows seeing plugin name from "Add Reference" dialog without resizing. FreeWheel SmartXML now supports new "Standard" event callback type. Other minor misc fixes and improvements ADDITIONAL DOWNLOADSSmo...WebSearch.Net: WebSearch.Net 3.1: WebSearch.Net is an open-source research platform that provides uniform data source access, data modeling, feature calculation, data mining, etc. It facilitates the experiments of web search researchers due to its high flexibility and extensibility. The platform can be used or extended by any language compatible for .Net 2 framework, from C# (recommended), VB.Net to C++ and Java. Thanks to the large coverage of knowledge in web search research, it is necessary to model the techniques and main...Umbraco CMS: Umbraco 4.10.0: NugetNuGet BlogRead the release blog post for 4.10.0. Whats newMVC support New request pipeline Many, many bugfixes (see the issue tracker for a complete list) Read the documentation for the MVC bits. Breaking changesWe have done all we can not to break backwards compatibility, but we had to do some minor breaking changes: Removed graphicHeadlineFormat config setting from umbracoSettings.config (an old relic from the 3.x days) U4-690 DynamicNode ChildrenAsList was fixed, altering it'...MySQL Tuner for Windows: 0.3: Welcome to the third beta of MySQL Tuner for Windows! This release fixes bugs in the displaying of numbers, and a crash that occurred due to the program incorrectly closing and disposing of resources, Be warned that there will be bugs in this release, so please do not use on production or critical systems. Do post details of issues found to the issue tracker, and I will endeavour to fix them, when I can. I would love to have your feedback, and if possible your support! Requirements Microso...SharePoint Manager 2013: SharePoint Manager 2013 Release ver 1.0.12.1106: SharePoint Manager 2013 Release (ver: 1.0.12.1106) is now ready for SharePoint 2013. The new version has an expanded view of the SharePoint object model and has been tested on SharePoint 2013 RTM. As a bonus, the new version is also available for SharePoint 2010 as a separate download.GL2DX (OpenGL to DirectX Wrapper Library): GL2DX Release 1: The first release contains all source code for the GL2DX library and source code for the sample project demonstrating how to use the library for a Direct3D / XAML hybrid Windows 8 application.WCF y Net remoting en el famoso ejemplo HOLA MUNDO: Ejemplo: Versión liberadaD3D9Client: D3D9Client R7: New release for Orbiter 2010-P1 - Added horizon/sun angle for night-lights into the configuration file (default 10deg) - Some runway lights related bugs are fixed - Added more configuration options for runway lightsFiskalizacija za developere: FiskalizacijaDev 1.2: Verzija 1.2. je, prije svega, odgovor na novu verziju Tehnicke specifikacije (v1.1.) koja je objavljena prije nekoliko dana. Pored novosti vezanih uz (sitne) izmjene u spomenutoj novoj verziji Tehnicke dokumentacije, projekt smo prošili sa nekim dodatnim feature-ima od kojih je vecina proizašla iz vaših prijedloga - hvala :) Novosti u v1.2. su: - Neusuglašenost zahtjeva (http://fiskalizacija.codeplex.com/workitem/645) - Sample projekt - iznosi se množe sa 100 (http://fiskalizacija.codeplex.c...MFCMAPI: October 2012 Release: Build: 15.0.0.1036 Full release notes at SGriffin's blog. If you just want to run the MFCMAPI or MrMAPI, get the executables. If you want to debug them, get the symbol files and the source. The 64 bit builds will only work on a machine with Outlook 2010 64 bit installed. All other machines should use the 32 bit builds, regardless of the operating system. Facebook BadgeJayData - The cross-platform HTML5 data-management library for JavaScript: JayData 1.2.3: JayData is a unified data access library for JavaScript to CRUD + Query data from different sources like OData, MongoDB, WebSQL, SqLite, HTML5 localStorage, Facebook or YQL. The library can be integrated with Knockout.js or Sencha Touch 2 and can be used on Node.js as well. See it in action in this 6 minutes video Sencha Touch 2 example app using JayData: Netflix browser. What's new in JayData 1.2.3 For detailed release notes check the release notes. TypeScript supportWrite your code in a ...MCEBuddy 2.x: MCEBuddy 2.3.7: Changelog for 2.3.7 (32bit and 64bit) 1. Improved performance of MP4 Fast and M4V Fast Profiles (no deinterlacing, removed --decomb) 2. Improved priority handling 3. Added support for Pausing and Resume conversions 4. Added support for fallback to source directory if network destination directory is unavailable 5. MCEBuddy now installs ShowAnalyzer during installation 6. Added support for long description atom in iTunesFoxyXLS: FoxyXLS Releases: Source code and samplesHTML Renderer: HTML Renderer 1.0.0.0 (3): Major performance improvement (http://theartofdev.wordpress.com/2012/10/25/how-i-optimized-html-renderer-and-fell-in-love-with-vs-profiler/) Minor fixes raised in issue tracker and discussions.Window Manager: Window Manager 1.0: First releaseProDinner - ASP.NET MVC Sample (EF4.4, N-Tier, jQuery): 8: update to ASP.net MVC Awesome 3.0 udpate to EntityFramework 4.4 update to MVC 4 added dinners grid on homepageASP.net MVC Awesome - jQuery Ajax Helpers: 3.0: added Grid helper added XML Documentation added textbox helper added Client Side API for AjaxList removed .SearchButton from AjaxList AjaxForm and Confirm helpers have been merged into the Form helper optimized html output for AjaxDropdown, AjaxList, Autocomplete works on MVC 3 and 4BlogEngine.NET: BlogEngine.NET 2.7: Cheap ASP.NET Hosting - $4.95/Month - Click Here!! Click Here for More Info Cheap ASP.NET Hosting - $4.95/Month - Click Here! If you want to set up and start using BlogEngine.NET right away, you should download the Web project. If you want to extend or modify BlogEngine.NET, you should download the source code. If you are upgrading from a previous version of BlogEngine.NET, please take a look at the Upgrading to BlogEngine.NET 2.7 instructions. If you looking for Web Application Project, ...Launchbar: Launchbar 4.2.2.0: This release is the first step in cleaning up the code and using all the latest features of .NET 4.5 Changes 4.2.2 (2012-11-02) Improved handling of left clicks 4.1.0 (2012-10-17) Removed tray icon Assembly renamed and signed with strong name Note When you upgrade, Launchbar will start with the default settings. You can import your previous settings by following these steps: Run Launchbar and just save the settings without configuring anything Shutdown Launchbar Go to the folder %LOCA...CommonLibrary.NET: CommonLibrary.NET 0.9.8.8: Releases notes for FluentScript located at http://fluentscript.codeplex.com/wikipage?title=Release%20Notes&referringTitle=Documentation Fluentscript - 0.9.8.8 - Final ReleaseApplication: FluentScript Version: 0.9.8.8 Build: 0.9.8.8 Changeset: 77368 ( CommonLibrary.NET ) Release date: November 2nd, 2012 Binaries: CommonLibrary.dll Namespace: ComLib.Lang Project site: http://fluentscript.codeplex.com/ Download: http://commonlibrarynet.codeplex.com/releases/view/90426 Source code: http://common...New Projects.NET Data Export Examples: This project is created to export data in C#,VB.NET from database,listview,command to PDF, Word,Excel,RTF,Html,XML,Access,DBF,SQL Script,SYLK,DIF,CSV,Clipboardb9b18a35-a80a-440c-bb8c-195be0225cfa: b9b18a35-a80a-440c-bb8c-195be0225cfaBudget Monkey: Personal Budgeting and Expense Tracking Application - ASP.Net MVC 4 - LINQ - Sql Server ClassLibrary5: ?0?????ORM ??:http://www.cnblogs.com/wushilonng/archive/2011/11/21/2257657.html ??????????????.CodeTextBox: CodeTextBox is a Windows Forms control for colorizing code while you are typing in the text box.Content Management System: web projectCopperfield: Copperfield is an extensibility framework built around contextual awareness. It is intended to be used in combination with one's DI / IoC framework of choice.Cyfuscator: This project show how create your own obfuscator for application .net, as a protection source codeData Browser: The Data Browser is a Windows 8 application that provides a great way to navigate and explore data (ODATA, RDF, ATOM, RDFa) published on the web. DevTask: Dev Task With MVC 4 and EF5DVB Viewer EPG Update Script: DVB Viewer EPG Update ScriptFcompress: Fcompress est un programme de compression simple, rapide et efficace de texte (mots). Programme conçu pour Eurêmaths, groupe Europole.Fdecompress: Fdecompress sert à décomprimer tout mot ou texte comprimer avec Fcompress.Hiren's Boot CD Program Launcher (Unicode support): Hiren's Boot CD Program Launcher (Unicode support)Image Gallery for WPF: A simple image gallery controlIMDb API: C# Class for grabbing data from the IMDb website.License Migration Live@edu Exchange to Office 365 A2: Only a little help to change the licenses after migration from Live@edu to Office 365MvcMSFootballManager: ASP MVC3 self-trainingNage: .NET Agent-based evolution frameworkOE NIK szakirány féléves: Féléves feladat.Office365 Helper: Office365 Helper is a collection of classes and methods to assist in administering and developing solutions for SharePoint online.Powershell Depo: This a collection of Powershell scripts that are collected and modified from anywhere and everywhere. Feel free to download whatever you need.Proejct13251109: sssProject13271109: sdfgdRemotableViewModel: The RemotableViewModel (RVM) library allows sharing of ViewModels accross process boundaries following the Model-View-ViewModel (MVVM) pattern.ScriptEngine: ScriptEngine for C#, JavaScript, VB. The ScriptEngine enables perform script snippets/files. In addition, the scripts can be cached.Shibboleth IdP Loader for ADFS: A PowerShell script to load Shibboleth federation IdPs as ADFS trusted claims providerSparklings: Game in which you change sparklings abilities using spots of light to help them reach the exit.Stala - Auto-update essentials: C# library and examples for event driven auto-updates without predefined graphical components/windows. Works with MSI packages and installer over web/intranet.STeaL : stealed functionarities from STL: STeaL is a .NET class library implemented with C# and enables you to use STL functionarities. especially, various of IList<T> extensions included.TechQueue: A series of Projects and code which are described in the blog http://techqueue.wordpress.comtesttom11082012git03: fsatesttom11082012tfs02: dsToyunda Phone: A simple searchable list of the songs available at the Karaoke rooms in the Epitanime event ran by students at the school named Epita in Paris.WebSearch.Net: WebSearch.Net is an open-source research platform that provides uniform data source access, data modeling, feature calculation, data mining, etc. Win8Controls: This project contains XAML based calendar control for WinRT / Windows Store Style application.WindowsCommonStorage: windows common storage

    Read the article

  • how can I fix error: hd0 out of disk?

    - by rux
    I am running Ubuntu 12.04 on a netbook - Acer AS 1410. After a download session, I restarted the computer and it said: error: hd0 out of disk. Press any key to continue... I pressed everything, but it's just frozen there. Any idea what's wrong with it and what I can do to fix it? I haven't been able to run my computer at all since it's frozen like that. Help please! I booted the live cd and ran sudo fdisk -lu into terminal, and here's what it gave me: Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders, total 117231408 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a696263 Device Boot Start End Blocks Id System /dev/sda3 2048 117229567 58613760 5 Extended /dev/sda5 * 71647232 109039615 18696192 83 Linux /dev/sda6 109041664 117229567 4093952 82 Linux swap / Solaris /dev/sda7 4096 71645183 35820544 83 Linux Partition table entries are not in disk order I am somewhat of a beginner in this, so don't know what this means. any ideas? Thanks!

    Read the article

  • 12.04 grub unable to boot on /sde, upgrade-grub and boot-repair failed, please help

    - by VGR
    My problem is I've 4 disks in a raid array listed as sda, sdb... sdd and grub 2 refuses to boot on /sde (the 5th disk, standalone and containing a clean install of 12.04 64 bits). I tried all solutions but all fail. (live CD/USB with grub-setup, also tried repair-grub, and tried also in the "grub rescue" set prefix= etc). I also tried to deactivate the RAID array in the BIOS, but I'd rather not destroy it, and I didn't find a way to make the standalone disk as '/sda1' (this would satisfy grub). In the BIOS, the would-be /sda is the only bootable hard disk; it ends up as /sde and grubs complains. I've made repair-grub issue a pastebin. I always end up in grub-rescue and I'm stuck. I need Ubuntu to boot so that I can add the device array handler for my disks. I can't switch the disks and I can't disconnect the SATA RAID controller. I need: (a) a workaround so that grub starts on /sde; or (b) a way to change the order in which Ubuntu sees the disks, at boot time. I could then provide grub with a /sda1. Thanks a lot. up please thanks a lot it's not the same problem as booting ubuntu from raid. My RAID array serves only of data repository windows had no problem with this configuration

    Read the article

  • Allow user to SUDO a script without password.

    - by John Isaacks
    I have a php script with this: <?php #echo exec('whoami'); $output = shell_exec('bash /usr/local/svn/bash_repo/make-live'); echo "$output"; ?> The make-live script contains this: #!/bin/bash cd /var/www-cake sudo svn checkout file:///usr/local/svn/bash_repo/repo/ echo "Head revision has been pushed to live server" So the PHP user who is www-data needs to have nopasswd for that script. I am told I need to add: www-data ALL=NOPASSWD: /usr/local/svn/bash_repo/make-live To sudoers to allow this. First I run sudo visudo but I have no experience with vi so I try to open it in gedit with export EDITOR=gedit && sudo -E visudo which then just opens a sudoers.tmp file which is empty. I add the line and save it. But it doesn't do save. So I just try sudo visudo and I add the line right beneath this part: # User privilege specification root ALL=(ALL) ALL www-data ALL=NOPASSWD: /usr/local/svn/bash_repo/make-live I closed out sudoers and reopened to verify that it has saved. I even restart apache. I run the php file and it still doesn't work. What am I missing?

    Read the article

  • How do create an encrypted system with multiple Linux distributions?

    - by niels
    A few weeks ago I created a completely encrypted system on a notebook and must say I like the idea. It's a little bit annoying to enter the password on every boot, but it's nice to know even if I loose the computer I don't give my data to other people. With the alternate-cd it's easy to do. Now I have to setup a new system where I want to combine the new idea with my usual usage strategy. There I have more partitions: 3 system, Home, Different Data-Partitions for vm-data, photo-data and mp3-data. The background is that I prefer not to update a system. I prefer to install the new version parallel to the old system. So I can easily test it. Obviously the Data-Partitions are used for both systems. My questions is, how can I easily combine both my strategy and the crypto-approach? Or is it impossible. The way to do the crypted stuff by hand is in my eyes to complicated.

    Read the article

  • Can windows XP be better than any Ubuntu (and Linux) distro for an old PC?

    - by Robert Vila
    The old laptop is a Toshiba 1800-100: CPU: Intel Celeron 800h Ram 128 MB (works ok) HDD: 15GB (works ok) Graphics adapter: Integrated 64-bit AGP graphics accelerator, BitBIT, 3D graphic acceleration, 8 MB Video RAM Only WindowsXP is installed, and works ok: it can be used, but it is slow (and hateful). I thought that I could improve performance (and its look) easily, since it is an old PC (drivers and everything known for years...) by installing a light Linux distro. So, I decided to install a light or customized Ubuntu distro, or Ubuntu/Debian derivative, but haven't been successful with any; not even booting LiveCDs: not even AntiX, not even Puppy. Lubuntu wiki says that it won't work because the last to releases need more ram (and some blogs say much more cpu -even core duo for new Lubuntu!-), let alone Xubuntu. The problems I have faced are: 1.There are thousands of pages talking about the same 10/15 lightweight distros, and saying more or less the same things, but NONE talks about a simple thing as to how should the RAM/swap-partition proportion be for this kind of installations. NONE! 2.Loading the LiveCD I have tried several different boot options (don't understand much about this and there's ALWAYS a line of explanation missing) and never receive error messages. Booting just stops at different stages but often seems to stop just when the X server is going to start. I am able to boot to command line. 3.I ignore whether the problem is ram size or a problem with the graphics driver (which surprises me because it is a well known brand and line of computers). So I don't know if doing a partition with a swap partition would help booting the LiveCD. 4.I would like to try the graphical interface with the LiveCD before installing. If doing the swap partition for this purpose would help. How can I do the partition? I tried to use Boot Rescue CD, but it advises me against continuing forward. I would appreciate any ideas as regards these questions. Thank you

    Read the article

  • Linux Journal Best Virtualization Solution Readers' Choice 2012

    - by Chris Kawalek
    I'm proud to report that in the latest issue of Linux Journal their readers named Oracle VM VirtualBox the "Best Virtualization Solution" for 2012. We're excited to receive this honor and want to thank Linux Journal and their readers for recognizing us!  This is the latest award won by Oracle VM VirtualBox, following a 2011 Bossie Award (best open source software) from InfoWorld, a 2012 Readers' Choice award from Virtualization Review, and several others. These awards help us know that people are using Oracle VM VirtualBox in their day to day work and that it's really useful to them. We truly appreciate their (your!) support. If you already use Oracle VM VirtualBox, you will know all this. But, just in case you haven't tried it yet, here's a few reasons you should download it: Free for personal use and open source. You can download it in minutes and start running multiple operating systems on your Windows PC, Mac, Oracle Solaris system, or Linux PC. It's fast and powerful, and easy to install and use. It has in-depth support for client technologies like USB, virtual CD/DVD, virtual display adapters with various flavors of 2D and 3D acceleration, and much more. If you've ever found yourself in a situation where you were concerned about installing a piece of software because it might be too buggy, or wanted to have a dedicated system to test things on, or wanted to run Windows on a Mac or Oracle Solaris on a PC (or hundreds of other combinations!), or didn't want to install your company's VPN software directly on your home system, then you should definitely give Oracle VM VirtualBox a try. Once you install it, you'll find a myriad of other uses, too. Thanks again to the readers of Linux Journal for selecting Oracle VM VirtualBox as the Best Virtualization Solution for 2012. If you'd like to read the whole article, you can purchase this month's issue over at the Linux Journal website. -Chris

    Read the article

  • Unknown filesystem error

    - by Ben
    My computer has (had) a dual boot of Ubuntu Precise and Windows 7. Recently, when I started the computer, grub gave me an error saying "Unknown filesystem", and sent me to grub rescue. I searched for solutions to this, and found this answer: Unknown filesystem error: grub rescue. I followed the instructions there, but they didn't really help: when I restarted the computer, it went straight to Windows without grub intervening at all (so it boots successfully, just not to the OS I want). This is the log from boot-repair. My Ubuntu partition is sda6. Naturally, I'm a little worried, since the log says "unknown filesystem type ''", which to me looks like the partition might be corrupt somehow. From the Ubuntu Live CD, I started gparted and looked at my partitions, and it also told me that my sda6 is an unknown filesystem. So my questions are basically: Can I restore Ubuntu to the way it was? If not, can I at least rescue the data I had on the partition somehow? Again, if I can't restore Ubuntu, how do I clean everything up so that I can reinstall it without too many complications? Another thing I should mention is that yesterday I had a similar problem where the computer told me there was a problem with the hard drive when it was starting, but it fixed itself by running fsck (that time it got past grub, and managed to start Ubuntu). Between that occasion and me having trouble booting the computer today, I have booted it successfully at least twice. Thanks for any help!

    Read the article

  • Portal and Content - Components, part 3 – Applied Customization Framework (4 of 7)

    - by Stefan Krantz
    Have you ever been challenged with the situation where your work task asks you to implement functionality in the WebCenter Portal and you browse through the Resource Catalog (Business Dictionary) and find the functionality you need. However when you get started there is small short comings and you ask your self- how can I re-use what is out of the box ca?- I wonder what code I need to use to produce the similar functions and include my new requirements?- Must I write a new taskflow? The answer to above questions are in many times answered with simply you can  do a taskflow customization to out-of-the-box taskflows. In this post I will help you understand how to do such customization. Best described is a 4 step process, see image flow below for illustration: Just to clarify few naming confusions that might occur when go through above process. Customization Role is a function within JDeveloper that will allow you to implement view and flow customizations to existing taskflows WebCenter Portal – Spaces Taskflow Customization Framework this technology scope do not only refer to WebCenter Spaces, this also include WebCenter Portal/Framework A taskflow customization do not overwrite or replace any code, it just creates an additional tip view of the taskflow in the MDS for the current application (WebCenter Portal or WebCenter Spaces) To sum up this simple procedure I also like to help you find your way around the main topic for this post series, this post series is focusing primarily on Content integration with WebCenter Portal, so where can I find content related taskflows in the WebCenter Libraries. The list below mention some useful locations to taskflows and each taskflow page fragments. Library Reference - WebCenter Document Library Service View Content Presenter Path: oracle.webcenter.doclib.view.jsf.taskflows.presenterTaskflow: contentPresenter.xml - The Content Presenter taskflowTaskflow: contentPresenterWizard.xml - The publishing wizard to select content, select template and preview including contributionDocument Manager Path: oracle.webcenter.doclib.view.jsf.taskflows.docManager Taskflow: documentManager.xml - The Document Manager taskflow which includes references to document management feature including browsing, download, uploading and viewing. For more information on Taskflow customizations please see following documentation:http://docs.oracle.com/cd/E23943_01/webcenter.1111/e10148/jpsdg_taskflows.htm#BACIEGJD

    Read the article

  • Two things I learned this week...

    - by noreply(at)blogger.com (Thomas Kyte)
    I often say "I learn something new about Oracle every day".  It really is true - there is so much to know about it, it is hard to keep up sometimes.Here are the two new things I learned - the first is regarding temporary tablespaces.  In the past - when people have asked "how can I shrink my temporary tablespace" I've said "create a new one that is smaller, alter your database/users to use this new one by default, wait a bit, drop the old one".  Actually I usually said first - "don't, it'll just grow again" but some people really wanted to make it smaller.Now, there is an easier way:http://docs.oracle.com/cd/E11882_01/server.112/e26088/statements_3002.htm#SQLRF53578Using alter tablespace temp shrink space .The second thing is just a little sqlplus quirk that I probably knew at one point but totally forgot.  People run into problems with &'s in sqlplus all of the time as sqlplus tries to substitute in for an &variable.  So, if they try to select '&hello world' from dual - they'll get:ops$tkyte%ORA11GR2> select '&hello world' from dual;Enter value for hello: old   1: select '&hello world' from dualnew   1: select ' world' from dual'WORLD------ worldops$tkyte%ORA11GR2> One solution is to "set define off" to disable the substitution (or set define to some other character).  Another oft quoted solution is to use chr(38) - select chr(38)||'hello world' from dual.  I never liked that one personally.  Today - I was shown another wayhttps://asktom.oracle.com/pls/apex/f?p=100:11:0::::P11_QUESTION_ID:4549764300346084350#4573022300346189787 ops$tkyte%ORA11GR2> select '&' || 'hello world' from dual;'&'||'HELLOW------------&hello worldops$tkyte%ORA11GR2>just concatenate '&' to the string, sqlplus doesn't touch that one!  I like that better than chr(38) (but a little less than set define off....)

    Read the article

  • Dual-Boot Windows 7 and Ubuntu 12.04.1

    - by z3matt
    I installed Ubuntu 12.04.1 alongside Windows 7. I wanted to check out what it's all about. By the way, i actually like the interface a lot and the free office suite is very very nice. I love how they can save to the .docx as well. Onto the story: I installed it using this tutorial and I set it all up and everything and things were great. I used the EasyBCD 2.2 Tool and created an Ubuntu 12.04.1 entry and when I boot the computer the Windows 7 and Ubuntu 12.04.1 option show up. However, when I click Ubuntu it does not boot. It say and error and says I must put in the Windows CD to repair or something like this. Here's my system specs: ASRock Extreme4 (EUFI BIOS) Corsair Vengaence 2x4GB nVidia GeForce 9800GT i5-3570K 3.4GHz Corsair 620W Modular 500GB WD Caviar Blue I have no clue what could be wrong with it and I would love any assistance. I am willing to mess around and if something happens wrong I can just reinstall windows and it won't be a huge deal. Thank you very much! Here are my partitions I made: /boot 500MB / 10000MB /home 20000MB swap area 4000MB BIOS 4000MB

    Read the article

  • How can I strip down Ubuntu?

    - by Thomas Owens
    I'm trying to fix what I consider a bloated install of Ubuntu. When I install Ubuntu on a machine, I get things that I don't want - web browsers, office applications, media players, accessibility utilities, Ubuntu One, and so on. My goal is to create a way that I can have an install of Ubuntu that contains only the most minimal packages - the administrative tools and package manager, a GUI (my preference would be GNOME), a text editor, core drivers (video cards, network cards - wired and wireless, input devices), and anything else that I have to have to run a stable distribution. From there, I would like to pick and choose which packages I install to create my own customized system. After playing around with other distros like Arch and Slackware, like how they provide a barebones install by default. However, I get trapped in a "configuration hell" - right now, I tried moving away from Ubuntu and to Arch, but after spending 6 hours with it, I still don't have a usable system. It's half configured and I don't have any usable software packages to enable me to work. Is anything that can help me available? Either something like the OpenSUSE builder that lets you choose applications and packages for the CD, an advanced installation mode where I can choose the packages to install and which to ignore, or a guide on how to strip Ubuntu down to its bare bones? And I suppose a natural follow up to this is once I have a stripped down Ubuntu, will this affect updating at all? When Canonical releases the next version of Ubuntu, I don't want any bloatware reinstalled. And yes, most of the applications that come with Ubuntu, I simply don't use. Ever.

    Read the article

  • Why is Rhythmbox becoming the default (again)?

    - by Christoph
    So, it seems with 12.04, they're switching back to Rhythmbox, after switching from Rhythmbox a year ago. I don't get why. They say that it's because of a blocking bug in GTK3# (if I understand that correctly), but that's just one bug, and in the same breath they say RB is not well maintained. It seems Ubuntu guys were dissatisfied with Banshee in some way, but apparently the Banshee guys were never notified of any problems. Also, it can't be to save disc space by dropping mono, because at the same day it was announced that the install disc will be enlarged by 50MB. Also, isn't it a bit shortsighted to push Banshee for default inclusion, and then drop it again a year later? How is that a sustainable use of dev resources, or consistent? Apparently there was quite some heavy effort by banshee devs - David Nielsen used the term "bending over backwards for Ubuntu" iirc. In summary: Can anyone shed more light on this? Related question: Why is Banshee becoming the default? Sources: http://www.omgubuntu.co.uk/2011/11/banshee-tomboy-and-mono-dropped-from-ubuntu-12-04-cd/ http://www.omgubuntu.co.uk/2011/11/rhythmbox-to-return-as-ubuntu-12-04-default-music-app/ http://www.omgubuntu.co.uk/2011/11/ubuntu-12-04-disc-size-to-be-750mb/ http://summit.ubuntu.com/uds-p/meeting/19442/desktop-p-default-apps/ http://banshee-media-player.2283330.n4.nabble.com/banshee-being-dropped-from-ubuntu-because-of-GTK3-support-td3985298.html

    Read the article

  • Virtualbox shared folder mount from fstab fails; works once bootup is complete

    - by Ben
    I've got Ubuntu 13.10 installed in Virtualbox 4.3. The host machine is Windows. I have a couple of Virtualbox shared folders being mounted by /etc/fstab. Until recently this setup worked just fine, but after upgrading from Ubuntu 13.04 and Virtualbox 4.2 (at essentially the same time) the fstab mounting stopped working. I get the following error during boot: An error occurred while mounting /home/benme/Documents. keys:Press S to skip mounting or M for manual recovery Pressing M for manual recovery and then trying to mount manually also fails: root@benme-vb:~# cd /home/benme root@benme-vb:/home/benme# mount Documents /sbin/mount.vboxsf: mounting failed with the error: No such device But if I instead skip mounting during boot, wait for Unity to start and then mount manually in a shell, everything works fine: benme-vb ~ % ls Documents benme-vb ~ % sudo mount Documents [sudo] password for benme: benme-vb ~ % ls Documents # actual file list omitted Note that when I mount manually I'm letting mount take all the options from /etc/fstab, and it works. This suggests to me that it's some sort of timing issue, where Virtualbox isn't "ready" to provide the shared file mounts at the point /etc/fstab mounts are run during bootup. Here's the fstab line, just for completeness: Documents /home/benme/Documents vboxsf uid=benme,gid=benme,dmode=774,fmode=664 0 0 Is there something I can do about this from the Ubuntu side? Or does anyone happen to know more about this from the Virtualbox angle? I've found an old report on the Virtualbox bug-tracker with identical symptoms, but in that case the user had updated Virtualbox without updating their guest additions and resolving that fixed the problem; this isn't happening here, I've definitely got the 4.3 guest additions installed.

    Read the article

  • Samba issue with sharing directories on NTFS/FAT32

    - by Microkernel
    I have some strange problems with Samba server. I am using samba Version 3.5.4 on Ubuntu 10.10. I have two Windows XP machines, one on VirtualBox on Ubuntu and another office laptop. Windows machine on VirtualBox has no issues in accessing the shared folders, but the laptop is not able to access all the shared content. The issue faced on laptop is the following. Shared folders on ext3 drives have no issues in accessing, but the contents shared on NTFS and FAT32 drives (mounted ones) are not accessible. When I try to open the shared folder, it asks for user name and password, but doesn't accept when I provide it. (Even if I provide admin login details). I changed workgroup value to the domain_name in office laptop, but still the problem persists. Here is the smdb.conf I am using: [global] workgroup = XXX.XXX.ORG server string = %h server (Samba, Ubuntu) map to guest = Bad User obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 dns proxy = No usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d guest ok = Yes [homes] comment = Home Directories [printers] comment = All Printers path = /var/spool/samba read only = No create mask = 0700 printable = Yes browseable = No [print$] comment = Samba server's CD-ROM path = /cdrom force user = nobody force group = nobody locking = No Workgroup was defined as "HOMENET" before, changed it to domain name on the office laptop thinking it was the problem, but for no avail.

    Read the article

  • How can create the smallest possible mirror of the archive?

    - by Registered User
    I need to create an http url at my laptop to have a Ubuntu installation begin within my laptop on a Xen environment. This is how the final thing will look like. The host and client are both going to be my laptop, I Googled and came across apt-mirror and some other packages. I do not want to archive entire 15 GB Ubuntu repositories on my machine. It is not possible to use a CD,ISO,loop mounted disk (reason mentioned below). I have tried using netboot image on local machine which failed because if you are attempting to create a virtual machine on a hardware which does not support VT virt-manager installer necessarily needs a URL of this sort http://archive.ubuntu.com/ubuntu/dists/hardy/main/installer-i386/current/images/netboot/ Any other option to create guest OS is simply grayed out. The unfortunate part is my Ethernet connections do not work when I boot with Xen-4.0 and a pv-ops Dom0 kernel from Jeremy's tree. Which is where I have to do this work. So I have to create a URL structure which is similar to Ubuntu mirrors. So how can I do this in bare minimum so that at least the console boots and once the console comes I can do some work.

    Read the article

  • Can't install Ubuntu on Asus Eee 1015pem

    - by Peter
    I'm having trouble to install Ubuntu. I use a ASUS Eee 1015pem netbook. Recently, I my netbook got wet. I had it inside my backback and all my things got wet. The netbook boots up fine but it will not load the OS. I downloaded ubuntu onto my external hard drive and changed the settings in my Bios to boot from a removable device. Nothing happens. When I plug in my external hard drive I'm not able to get to the boot icon. I have to unplug it the external hard drive. Set my boot settings I tried both Removable and CD-Rom. Than I plug my external drive back in and nothing happens on either settings. My Asus never came with a recovery disk and suppose to have a build in recovery by pressing F9 in the Bios. Also I need to disable Boot Booster in Bios and Boot Booster is not even an opition in Bios. My friend told me try installing Ubuntu but now I'm having no luck with Ubuntu. Any suggestions?

    Read the article

  • Grub loading unknown file system grub rescue

    - by Ashish Kumar
    I am new to Linux. I had Windows 7 installed in my laptop. Yesterday I installed Ubuntu 9.0 from a free CD I got. I choose the option "Install side by side with Windows 7 loader (something like that..)". Everything went fine & I installed Ubuntu. When I restarted, I could easily boot from both Windows 7 & Ubuntu. But later when I booted from Windows 7, I did a disk management by right clicking "my Computer" & choosing the option "Manage". Actually I deleted a drive & added that empty volume in another drive. Now when I start my system it shows the following error: Grub loading Unknown file system grub rescue> I have no clue what to do now. Please help me at urgent. Any solution in layman's language is greatly appreciated. P.S. I want all my files on both Windows 7 & Ubuntu.

    Read the article

  • Netcat I/O enhancements

    - by user13277689
    When Netcat integrated into OpenSolaris it was already clear that there will be couple of enhancements needed. The biggest set of the changes made after Solaris 11 Express was released brings various I/O enhancements to netcat shipped with Solaris 11. Also, since Solaris 11, the netcat package is installed by default in all distribution forms (live CD, text install, ...). Now, let's take a look at the new functionality: /usr/bin/netcat alternative program name (symlink) -b bufsize I/O buffer size -E use exclusive bind for the listening socket -e program program to execute -F no network close upon EOF on stdin -i timeout extension of timeout specification -L timeout linger on close timeout -l -p port addr previously not allowed usage -m byte_count Quit after receiving byte_count bytes -N file pattern for UDP scanning -I bufsize size of input socket buffer -O bufsize size of output socket buffer -R redir_spec port redirection addr/port[/{tcp,udp}] syntax of redir_spec -Z bypass zone boundaries -q timeout timeout after EOF on stdin Obviously, the Swiss army knife of networking tools just got a bit thicker. While by themselves the options are pretty self explanatory, their combination together with other options, context of use or boundary values of option arguments make it possible to construct small but powerful tools. For example: the port redirector allows to convert TCP stream to UDP datagrams. the buffer size specification makes it possible to send one byte TCP segments or to produce IP fragments easily. the socket linger option can be used to produce TCP RST segments by setting the timeout to 0 execute option makes it possible to simulate TCP/UDP servers or clients with shell/python/Perl/whatever script etc. If you find some other helpful ways use please share via comments. Manual page nc(1) contains more details, along with examples on how to use some of these new options.

    Read the article

  • Trouble installing Ubuntu 12.04 from USB

    - by Kyle J
    I want to dual-boot Ubuntu Desktop 12.04 on my new ultrabook which has an Intel i7 3517U processor 6GB RAM Windows 7, 64-bit no CD/DVD drive I created my bootable USB stick using pendrivelinux.com with the "ubuntu-12.04.1-desktop-i386.iso". I am following these directions because they include nice screenshots; however, I do not get very far in the process. I am able to boot into the Live Desktop, and then I try to install onto my hard disk. Here are the series of actions that I take next: First, I see this ( http://i.imgur.com/vucYH ) window, and click 'continue' Then I get this ( http://imgur.com/2wESc ) window, and click 'continue' again This appears: and I get worried because it seems like there is no recognition that I have Windows installed. According to the directions I am following, I should see /dev/sda1 and /dev/sda2 partitions. In the drop-down menu at the bottom the only "Device for boot loader installation" is /dev/sdb and no information is shown. I am hesitant to click 'Install Now' for fear of what it might do to Windows. 4. I click 'Quit' and cancel the installation, but then about 5 seconds later this ( http://imgur.com/a/yXi0C ) window pops up (I have expanded it to full screen to scroll and show all the details). 5. Another second later this ( http://imgur.com/vxcrN ) comes up. I'm not sure how relevant this is. Does anyone have any insight into this issue?? Why does it not show my current Windows partition? What would happen if I tried to continue with the installation process? Thanks! PS - sorry, it would only let me post 2 hyperlinks as a new user

    Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >