Search Results

Search found 9923 results on 397 pages for 'state'.

Page 129/397 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• Routing table on Linux not respected

  - by MRHaarmann

  I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

  Read the article

• CLOSE_WAIT sockets burst - perhaps because of iptables settings?

  - by Fabrizio Giudici

  I have an Ubuntu 12.04 server virtual box where basically the installed software and configuration are the default ones, plus the installation of a jetty 6 server which servers a few websites. To keep things simple I didn't install apache httpd and used iptables for exposing jetty (which runs on the 8080 port) to the port 80. These are the results of /sbin/iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination REDIRECT tcp -- anywhere localhost tcp dpt:http redir ports 8080 REDIRECT tcp -- anywhere Ubuntu-1104-natty-64-minimal tcp dpt:http redir ports 8080 Chain POSTROUTING (policy ACCEPT) target prot opt source destination I must confess I have a shallow comprehension of how iptables works, in particular for the different kind of chains. This thing works, but sometimes I have an explosion of sockets that stay permanently in CLOSE_WAIT state. I know about what this state means, but since I didn't write the code that manages servlets (they are handled by jetty) I can't fix the problem by patching my code. Eventually the amount of CLOSE_WAIT sockets builds up and makes the server not responsive, so I have to restart jetty. I've looked around for similar problems wth CLOSE_WAIT, and only found cases related to the programmer's code, or problems with Tomcat, not Jetty. I was wondering whether they could be related to a partially broken iptables configuration (the alternative is a bug in Jetty 6, but I first want to exclude other possible causes). Thanks.

  Read the article

• How do I reinitialise a failed RAID 5 drive using terminal on Ubuntu Server

  - by Stephen

  I've currently put together a new system and part of that has been creating a software RAID 5 using 'mdadm' in Ubuntu Server. I successfully got to the point where I create the array using: sudo mdadm --create --verbose /dev/md0 --level=5 --raid-devices=4 /dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd1 I left it to do its thing overnight then used the following command to check on it: watch cat /proc/mdstat To which the following was returned: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sdd1[4](S) sdc1[2] sdb1[1] sda1[0](F) 5860535808 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/2] [_UU_] unused devices: <none> It appears that one has failed (and I'm not too savvy with why another is a spare). So, just to be sure that something else isn't amiss I wanted to try and re-engage the failed drive. Can someone explain how I can do that and what I should do with the spare (if anything). And also how do I know when synchronisation is complete? The tutorial I used to get this far is located here: http://sonniesedge.co.uk/2009/06/13/software-raid-5-on-ubuntu-904/ Many thanks! p.s. Here is some extra information that may help: sudo mdadm --detail /dev/md0 /dev/md0: Version : 1.2 Creation Time : Mon Jun 18 21:14:21 2012 Raid Level : raid5 Array Size : 5860535808 (5589.04 GiB 6001.19 GB) Used Dev Size : 1953511936 (1863.01 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Mon Jun 18 21:50:26 2012 State : clean, FAILED Active Devices : 2 Working Devices : 3 Failed Devices : 1 Spare Devices : 1 Layout : left-symmetric Chunk Size : 512K Name : myraidbox:0 (local to host myraidbox) UUID : a269ee94:a161600c:fb1665e7:bd2f27b3 Events : 13 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 33 2 active sync /dev/sdc1 3 0 0 3 removed 0 8 1 - faulty spare /dev/sda1 4 8 49 - spare /dev/sdd1

  Read the article

• server 2008 r2 stuck on installing updates

  - by volody

  I have 2008 r2 64bit server that is stuck on installing updates. It shows message "Please do not power off or unplug your machine. Installing 57 of 61.." This message is shown for 3 hours now. I was trying to connect to this server using mmc. runas /user:AdministratorAccountName@ComputerName "mmc %windir%\system32\compmgmt.msc" RUNAS ERROR: Unable to run - mmc C:\Windows\system32\compmgmt.msc 1311: There are currently no logon servers available to service the logon request. What else can I do? Update: Remote Desktop does not work. It just disappear after entering username and password from Win7-64 computer Update: I have disconected server. Now Server Manager in Roles Summary shows message "Unexpected error refreshing Server Manager: The remote procedure call failed." Event log shows Could not discover the state of the system. An unexpected exception was found: System.Runtime.InteropServices.COMException (0x800706BE): The remote procedure call failed. (Exception from HRESULT: 0x800706BE) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Windows.ServerManager.ComponentInstaller.ThrowHResult(Int32 hr) at Microsoft.Windows.ServerManager.ComponentInstaller.CreateSessionAndPackage(IntPtr& session, IntPtr& package) at Microsoft.Windows.ServerManager.ComponentInstaller.InitializeUpdateInfo() at Microsoft.Windows.ServerManager.ComponentInstaller.Initialize() at Microsoft.Windows.ServerManager.Common.Provider.RefreshDiscovery() at Microsoft.Windows.ServerManager.LocalResult.PerformDiscovery() at Microsoft.Windows.ServerManager.ServerManagerModel.CreateLocalResult(RefreshType refreshType) at Microsoft.Windows.ServerManager.ServerManagerModel.InternalRefreshModelResult(Object state) Update: Manual update hangs on (Installing update 58 of 62...) Seurity Update for Windows Server 2008 R2 x64 Edition (KB979309) Update: It could be an issue with that admin user was renamed

  Read the article

• IPC between multiple processes on multiple servers

  - by z8000

  Let's say you have 2 servers each with 8 CPU cores each. The servers each run 8 network services that each host an arbitrary number of long-lived TCP/IP client connections. Clients send messages to the services. The services do something based on the messages, and potentially notify N1 of the clients of state changes. Sure, it sounds like a botnet but it isn't. Consider how IRC works with c2s and s2s connections and s2s message relaying. The servers are in the same data center. The servers can communicate over a private VLAN @1GigE. Messages are < 1KB in size. How would you coordinate which services on which host should receive and relay messages to connected clients for state change messages? There's an infinite number of ways to solve this problem efficiently. AMQP (RabbitMQ, ZeroMQ, etc.) Spread Toolkit N^2 connections between allservices (bad) Heck, even run IRC! ... I'm looking for a solution that: perhaps exploits the fact that there's only a small closed cluster is easy to admin scales well is "dumb" (no weird edge cases) What are your experiences? What do you recommend? Thanks!

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• SendMail not working in CentOs 6.4

  - by Kane

  I am trying to send e-mails from my CentOS 6.4 but it does not work. My knowledge about servers is quite limited, so I hope someone can help me. Here is what I did: First i tried to send an email using the "mail" command, but it was not in the OS so I installed it. # yum install mailx After that, I tried sending an email using the "mail" command, but it did not send anything. I checked it on the internet and I realized I needed an e-mail server like sendmail, so I installed it. # yum install sendmail sendmail-cf sendmail-doc sendmail-devel After that, I configured it following some tutorials. First, sendmail.mc file. # vi /etc/mail/sendmail.mc Commented out the next line: BEFORE # DAEMON_OPTIONS('Port=smtp, Name=MTA') dnl AFTER # dnl DAEMON_OPTIONS('Port=smtp, Name=MTA') dnl Check that the next lines are correct: # FEATURE(`virtusertable', `hash -o /etc/mail/virtusertable.db')dnl # ... # FEATURE(use_cw_file)dnl # ... # FEATURE(`access_db', `hash -T<TMPF> -o /etc/mail/access.db')dnl Update sendmail.cf # m4 /etc/mail/sendmail.mc > /etc/mail/sendmail.cf Open the port 25 adding the proper line in the iptables file # vi /etc/sysconfig/iptables # -A INPUT -m state --state NEW -m tcp --dport 25 -j ACCEPT restart iptables and sendmail # service iptables restart # service sendmail restart So i thought that would be ok, but when i tried: # mail '[email protected]' # Subject: test subject # test content #. I checked the mail log: # vi /var/log/maillog And that is what I found: Aug 14 17:36:24 dev-admin-test sendmail[20682]: r7D8RItS019578: to=<[email protected]>, ctladdr=<[email protected]> (0/0), delay=1+00:09:06, xdelay=00:00:00, mailer=esmtp, pri=2460500, relay=alt4.gmail- smtp-in.l.google.com., dsn=4.0.0, stat=Deferred: Connection timed out with alt4.gmail-smtp-in.l.google.com. I do not understand why there is a connection time out. Am I missing something? Can anyone help me, please? Thank you.

  Read the article

• SQL Server log backups "stalling"

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• Which isn't working on linode servers (Ubuntu 10.04)?

  - by chrisjlee

  Currently trying to configure a linode server running on ubuntu 10.04. I utilized a stackscript (Default drupal profile) which seemed to run successfully. The log indicate so as well. Then ssh'd into the server (as root) to try to configure php. When i run a which php, which php5 they both return nothing. A which python returns something though. I know where the default path to php but i usually just like to use it as confirmation that php exists. Do i have to modify some configurations to enable which to work? Also tab completion doesn't seem to work for when i apt-get install? Update: Thanks for the suggestions guys. I've ran a couple commands and no luck either: [ root@ ~ ] $ dpkg -l |grep php [ root@ ~ ] $ apt-get install php5-cli Reading package lists... Done Building dependency tree Reading state information... Done Package php5-cli is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package php5-cli has no installation candidate Then i tried installing php and php cli: [ root@ ~ ] $ sudo apt-get install php5 php5-cli sudo: unable to resolve host xxxxxxx Reading package lists... Done Building dependency tree Reading state information... Done Package php5 is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Package php5 has no installation candidate

  Read the article

• How to force mdadm to stop RAID5 array?

  - by lucek

  I have /dev/md127 RAID5 array that consisted of four drives. I managed to hot remove them from the array and currently /dev/md127 does not have any drives: cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdd1[0] sda1[1] 304052032 blocks super 1.2 [2/2] [UU] md1 : active raid0 sda5[1] sdd5[0] 16770048 blocks super 1.2 512k chunks md127 : active raid5 super 1.2 level 5, 512k chunk, algorithm 2 [4/0] [____] unused devices: <none> and mdadm --detail /dev/md127 /dev/md127: Version : 1.2 Creation Time : Thu Sep 6 10:39:57 2012 Raid Level : raid5 Array Size : 8790402048 (8383.18 GiB 9001.37 GB) Used Dev Size : 2930134016 (2794.39 GiB 3000.46 GB) Raid Devices : 4 Total Devices : 0 Persistence : Superblock is persistent Update Time : Fri Sep 7 17:19:47 2012 State : clean, FAILED Active Devices : 0 Working Devices : 0 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 512K Number Major Minor RaidDevice State 0 0 0 0 removed 1 0 0 1 removed 2 0 0 2 removed 3 0 0 3 removed I've tried to do mdadm --stop /dev/md127 but: mdadm --stop /dev/md127 mdadm: Cannot get exclusive access to /dev/md127:Perhaps a running process, mounted filesystem or active volume group? I made sure that it's unmounted, umount -l /dev/md127 and confirmed that it indeed is unmounted: umount /dev/md127 umount: /dev/md127: not mounted I've tried to zero superblock of each drive and I get (for each drive): mdadm --zero-superblock /dev/sde1 mdadm: Unrecognised md component device - /dev/sde1 Here's output of lsof|grep md127: lsof|grep md127 md127_rai 276 root cwd DIR 9,0 4096 2 / md127_rai 276 root rtd DIR 9,0 4096 2 / md127_rai 276 root txt unknown /proc/276/exe What else can I do? LVM is not even installed so it can't be a factor.

  Read the article

• LXC, Port forwarding and iptables

  - by Roberto Aloi

  I have a LXC container (10.0.3.2) running on a host. A service is running inside the container on port 7000. From the host (10.0.3.1, lxcbr0), I can reach the service: $ telnet 10.0.3.2 7000 Trying 10.0.3.2... Connected to 10.0.3.2. Escape character is '^]'. I'd love to make the service running inside the container accessible to the outer world. Therefore, I want to forward port 7002 on the host to port 7000 on the container: iptables -t nat -A PREROUTING -p tcp --dport 7002 -j DNAT --to 10.0.3.2:7000 Which results in (iptables -t nat -L): DNAT tcp -- anywhere anywhere tcp dpt:afs3-prserver to:10.0.3.2:7000 Still, I cannot access the service from the host using the forwarded port: $ telnet 10.0.3.1 7002 Trying 10.0.3.1... telnet: Unable to connect to remote host: Connection refused I feel like I'm missing something stupid here. What things should I check? What's a good strategy to debug these situations? For completeness, here is how iptables are set on the host: iptables -F iptables -F -t nat iptables -F -t mangle iptables -X iptables -P INPUT DROP iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p icmp --icmp-type echo-request -j ACCEPT iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -t nat -A POSTROUTING -o lxcbr0 -j MASQUERADE iptables -t nat -A PREROUTING -p tcp --dport 7002 -j DNAT --to 10.0.3.2:7000

  Read the article

• How to display/define Mirror/Stripping pairs with mdadm

  - by Chris

  I want to make a standard linux software Raid10 over 4 HDD. The server has 4HDDs, 2 pairs from different vendors in order to avoid batch problems. I want to have the mirror over two different Vendors, and then the Stripe over the mirror pairs. I could do that by manually creating Raid1/0, but mdadm supports Raid level 10. I just cant figure out how the Raid10 is then handled and how the data is distributed. mdadm --detail /dev/md10 /dev/md10: Version : 1.2 Creation Time : Wed May 28 11:06:23 2014 Raid Level : raid10 Array Size : 1953260544 (1862.77 GiB 2000.14 GB) Used Dev Size : 976630272 (931.39 GiB 1000.07 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Update Time : Wed May 28 11:06:23 2014 State : clean, resyncing (PENDING) Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 512K Name : pdwhost:10 (local to host pdwhost) UUID : a3de0ad5:9e694ee1:addc6786:c4449e40 Events : 0 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 113 3 active sync /dev/sdh1 does not really give any information about that. How it should be: Raid 1 / Mirror over /dev/sda1 /dev/sdf1 and /dev/sdg1 /dev/sdh1 Raid 0 over the two Raid 1 pairs Is it possible to do that with the built in "level=10", how can I see what pairs are mirrored? Thanks a lot for you help

  Read the article

• How to delete a podcast from an iPod and not have it reappear after syncing with iTunes?

  - by Mike

  Hi everyone, Say I have subscribe to a single podcast and I have Episode 1 and Episode 2 on my iPod. Each episode is 30 minutes long. I listen to the entirety of Episode 1 and just the first 15 minutes of Episode 2. I delete Episode 1 using my iPod's menu. Say Episode 3 has just come out. I want to be able to sync with iTunes, and after doing so, have just Episodes 2 and 3 on my iPod (with Episode 2 "half listened to"). How can I do this? Ideal state... Episode 1 = deleted Episode 2 = 15 minutes played already Episode 3 = unplayed I've found that if I set the Sync Podcast option in iTunes to "all new", I get: "All new" Episode 1 = not on the iPod Episode 2 = not on the iPod Episode 3 = unplayed and if I set the Sync Podcast option in iTunes to "all unplayed" "All unplayed" Episode 1 = unplayed Episode 2 = 15 minutes played already Episode 3 = unplayedv neither option does what I want. Is there an option to get my "ideal state"?

  Read the article

• My home router randomly disconnects me and I'm unable to reconnect to it

  - by Roy Tang

  It's happened a few times, I'm not sure how to diagnose/debug, so any advise would be appreciated. Symptons: sometimes the router will randomly disconnect; the connection icon on my desktop (wired to the router) gets that yellow "!" symbol that tells me my connection just went down. At this point I'm unable to ping the router. afterwards I try to reset the router by removing then reconnecting the power jack on the router side (this is the fastest way as I can't reset the power strip it's connected to without rebooting my desktop. the router has a reset thingy, but it's one of those things where i have to find a pin to stick into the hole, and when I get disconnected I usually need to get reconnected immediately so I just pull and put back the power jack), but even after that the connection has the same state. after the router reboots, if I try to connect to it using a wifi device like my ipad, the ipad prompts me for the wifi password even though it had already "remembered" all the settings for this router forever after i finally decide to reboot the power strip, and my desktop and the router boot up again, the connection returns to its normal state somewhat and i'm able to connect to it as normal using the desktop and wifi devices. What do I need to check the next time this happens so I can figure out the problem? Is it possibly because we've been using the power jack on the router as an easier way to reboot it? Should I be shopping around for a new router? If it helps, the router is a DLink DIR-300

  Read the article

• Backup data from RAID 1 disk out of its server

  - by Doomsday

  I'm facing with a pretty easy problem in my opinion. I've extracted a working disk from a RAID1 and I'm looking to copy only data (FS and RAID configuration doesn't matter) into another location (another FS). My problem is I'm not able to mount properly this disk into another linux. I've first looked the partition table : # fdisk -l /dev/sdc Disk /dev/sdc: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 63 1249535699 624767818+ fd Linux raid autodetect /dev/sdc2 1249535700 1250017649 240975 fd Linux raid autodetect /dev/sdc3 1250017650 1250258624 120487+ 82 Linux swap / Solaris I've understood I should use dmraid tools. Once installed : # cat /proc/mdstat Personalities : md0 : inactive sdc1[1](S) 624767744 blocks unused devices: <none> And some other informations : # mdadm --examine /dev/sdc1 /dev/sdc1: Magic : a92b4efc Version : 0.90.00 UUID : 8f292f54:7e5aef72:7e5ab5fd:b348fd05 Creation Time : Mon Jun 2 03:39:41 2008 Raid Level : raid1 Used Dev Size : 624767744 (595.82 GiB 639.76 GB) Array Size : 624767744 (595.82 GiB 639.76 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Update Time : Tue Feb 7 22:34:59 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Checksum : a505b324 - correct Events : 15148 Number Major Minor RaidDevice State this 1 8 1 1 active sync /dev/sda1 0 0 8 17 0 active sync /dev/sdb1 1 1 8 1 1 active sync /dev/sda1 From here, I've tried to mount but I'm not comfortable with dmtools and how it's working. # mount /dev/sdc1 /mnt/sdc1 mount: unknown filesystem type 'linux_raid_member' # mount /dev/md0 /mnt/sdc1 mount: /dev/md0: can't read superblock I've seen some options to alter RAID array with mdadm but I only want to copy data on its filesystem before wiping them... Anyone has a clue ?

  Read the article

• xen + debian network after upgrade squeeze to wheeze

  - by rush

  I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

  Read the article

• OpenBSD pf - implementing the equivalent of an iptables DNAT

  - by chutz

  The IP address of an internal service is going to change. We have an OpenBSD access point (ssh + autpf rules) where clients connect and open a connection to the internal IP. To give us more time to reconfigure all clients to use the new IP address, I thought we can implement the equivalent of a DNAT on the authpf box. Basically, I want to write a rule similar to this iptables rule which lets me ping both $OLD_IP and $NEW_IP. iptables -t nat -A OUTPUT -d $OLD_IP -j DNAT --to-dest $NEW_IP Our version of OpenBSD is 4.7, but we can upgrade if necessary. If this DNAT is not possible we can probably do a NAT on a firewall along the way. The closest I was able to accomplish on a test box is: pass out on em1 inet proto icmp from any to 10.68.31.99 nat-to 10.68.31.247 Unfortunately, pfctl -s state tells me that nat-to translates the source IP, while I need to translate the destination. $ sudo pfctl -s state all icmp 10.68.31.247:7263 (10.68.30.199:13437) -> 10.68.31.99:8 0:0 I also found lots of mentions about rules that start with rdr and include the -> symbol to express the translation, but it looks like this syntax has been obsoleted in 4.7 and I cannot get anything similar to work. Attempts to implement a rdr fail with a complaint that /etc/pf.conf:20: rdr-to can only be used inbound

  Read the article

• Log backups "stalling" on SQL 2008?

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• Windows Small Business System 2003. SQL timeout in Server Performance Report

  - by tetranz

  I'm the volunteer IT admin at a small school. We have SBS 2003 with about ten desktops. The server performance report is emailed to me daily. It is setup with a wizard in the Monitoring and Performance part of the "Server Management" console. It often fails with a "The page cannot be displayed" error. The event log shows Event Type: Error Event Source: ServerStatusReports Event Category: None Event ID: 1 Date: 1/16/2011 Time: 6:03:14 AM User: N/A Computer: ALPHA Description: Server Status Report: URL: http://localhost/monitoring/perf.aspx?reportMode=1&allHours=1 Error Message: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. Stack Trace: at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, TdsParserState state) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, TdsParserState state) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning() at System.Data.SqlClient.TdsParser.ReadNetlib(Int32 bytesExpected) [plus lots more stack trace] This has been happening for years :) I've never really solved it. It seems to be related to WSUS. When it happens, I run the Update Services "Server Cleanup Wizard". That takes a long time to run. If I haven't run it for a while it can take 10 hours. I also run the WsusDBMaintenance.sql script (from TechNet I think) which reindexes the database etc. Those two things seem to get it working again for a while. Recently the "while" has become a couple of weeks. My searching online has revealed lots of people having this problem but no real solution. Does anyone have any good ideas about this? I have to wonder if something in the WSUS SQL schema is not indexed properly. The time that the server cleanup wizard takes seems ridiculous. Thanks

  Read the article

• why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

  - by rjnagle

  In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

  Read the article

• Possible attack on my SQL server?

  - by erizias

  Checking my SQL Server log I see several entries like this: Date: 08-11-2011 11:40:42 Source: Logon Message: Login failed for user 'sa'. Reason: Password did not match for the login provided. [CLIENT: 56.60.156.50] Date: 08-11-2011 11:40:42 Source: Logon Message: Error: 18456. Severity: 14. State: 8. Date: 08-11-2011 11:40:41 Source: Logon Message: Login failed for user 'sa'. Reason: Password did not match for the login provided. [CLIENT: 56.60.156.50] Date: 08-11-2011 11:40:41 Source: Logon Message: Error: 18456. Severity: 14. State: 8. And so on.. Is this a possible attack on my SQL Server from the chineese???! I looked up the IP adress, at ip-lookup.net which stated it was chineese. And what to do? - Block the IP adress in the firewall? - Delete the user sa? And how do I protect my web server the best?! :) Thanks in advance!

  Read the article

• How do I add a second disk to my zfs root pool

  - by ankimal

  I am trying to add a new disk to my zfs root pool. Here is my current config: zpool status pool: rpool state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM rpool ONLINE 0 0 0 c0d0s0 ONLINE 0 0 0 errors: No known data errors bash-3.00# df -h Filesystem Size Used Avail Use% Mounted on rpool/ROOT/s10x_u7wos_08 311G 18G 293G 6% / swap 14G 384K 14G 1% /etc/svc/volatile /usr/lib/libc/libc_hwcap1.so.1 311G 18G 293G 6% /lib/libc.so.1 swap 14G 52K 14G 1% /tmp swap 14G 40K 14G 1% /var/run rpool/export 293G 19K 293G 1% /export rpool/export/home 430G 138G 293G 32% /export/home rpool 293G 36K 293G 1% /rpool # format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c0d0 <DEFAULT cyl 60797 alt 2 hd 255 sec 63> /pci@0,0/pci-ide@1f,2/ide@0/cmdk@0,0 1. c2d0 <Hitachi- JK1181YAHL0YK-0001-16777216.> /pci@0,0/pci-ide@1f,5/ide@1/cmdk@0,0 Disk 1 above is the new disk I need to attach to expand my root pool (give /export/home some extra space). If I try to attach my new disk to the pool # zpool attach -f rpool c0d0s0 c2d0s0 cannot attach c2d0s0 to c0d0s0: new device must be a single disk # uname -a SunOS dsol1 5.10 Generic_139556-08 i86pc i386 i86pc Solaris Any ideas?

  Read the article

• RAID degraded on Ubuntu server

  - by reano

  We're having a very weird issue at work. Our Ubuntu server has 6 drives, set up with RAID1 as follows: /dev/md0, consisting of: /dev/sda1 /dev/sdb1 /dev/md1, consisting of: /dev/sda2 /dev/sdb2 /dev/md2, consisting of: /dev/sda3 /dev/sdb3 /dev/md3, consisting of: /dev/sdc1 /dev/sdd1 /dev/md4, consisting of: /dev/sde1 /dev/sdf1 As you can see, md0, md1 and md2 all use the same 2 drives (split into 3 partitions). I also have to note that this is done via ubuntu software raid, not hardware raid. Today, the /md0 RAID1 array shows as degraded - it is missing the /dev/sdb1 drive. But since /dev/sdb1 is only a partition (and /dev/sdb2 and /dev/sdb3 are working fine), it's obviously not the drive that's gone AWOL, it seems the partition itself is missing. How is that even possible? And what could we do to fix it? My output of cat /proc/mdstat: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid1 sda2[0] sdb2[1] 24006528 blocks super 1.2 [2/2] [UU] md2 : active raid1 sda3[0] sdb3[1] 1441268544 blocks super 1.2 [2/2] [UU] md0 : active raid1 sda1[0] 1464710976 blocks super 1.2 [2/1] [U_] md3 : active raid1 sdd1[1] sdc1[0] 2930133824 blocks super 1.2 [2/2] [UU] md4 : active raid1 sdf2[1] sde2[0] 2929939264 blocks super 1.2 [2/2] [UU] unused devices: <none> FYI: I tried the following: mdadm /dev/md0 --add /dev/sdb1 But got this error: mdadm: add new device failed for /dev/sdb1 as 2: Invalid argument Output of mdadm --detail /dev/md0 is: /dev/md0: Version : 1.2 Creation Time : Sat Dec 29 17:09:45 2012 Raid Level : raid1 Array Size : 1464710976 (1396.86 GiB 1499.86 GB) Used Dev Size : 1464710976 (1396.86 GiB 1499.86 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 15:55:07 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : lia:0 (local to host lia) UUID : eb302d19:ff70c7bf:401d63af:ed042d59 Events : 26216 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 0 0 1 removed

  Read the article

• Library conflict in Mac OS X

  - by Juan Medín

  I was trying to install the ImageMagick library on Mac OS X Snow Leopard, and first I tried port and, after it failed, homebrew. It updated some dependencies and installed ImageMagick without problems. So far so good. The problem came when I ran Apache. I got the following error in the system log: 07/04/11 12:55:15 org.apache.httpd[41841] httpd: Syntax error on line 115 of /private/etc/apache2/httpd.conf: Cannot load /opt/local/apache2/modules/libphp5.so into server: dlopen(/opt/local/apache2/modules/libphp5.so, 10): Library not loaded: /opt/local/lib/libpng12.0.dylib\n Referenced from: /opt/local/apache2/modules/libphp5.so\n Reason: image not found I checked the /opt/local/lib and surprise! I don't have the libpng12.0 but the libpng14.0. So, as far as I can tell, something went wrong installing the ImageMagick library. Now, I can't find a way to rollback to the previous libraries, other than copying them from the backup. Do you know if is there a way to recover the previous state or reinstall Apache? Or is this just a corrupt state and I must reinstall OS X?

  Read the article

• SQL Server log backups “stalling”

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >