Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 129/343 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

• Second ip address on same interface CentOS 6.3

  - by user16081

  I tried to add a second LAN addresses in CentOS 6.3 on a brand new install and it's not working. I installed a new copy of CentOS 5.7 and tried the same and it worked right away. Now I'm just trying to setup the alias on the same subnet and it's not working. what am i doing wrong, is this not possible on CentOS 6.3? second ip address on the same interface but on a different subnet CentOS 5.7 it works: DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:01:6F:89 IPADDR=192.168.0.167 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes DEVICE=eth0:0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:01:6F:89 IPADDR=192.168.0.166 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes On CentOS 6.3: does not work DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:1E:DE:86 IPADDR=192.168.0.242 NETMASK=255.255.255.0 NETWORK=192.168.0.0 GATEWAY=192.168.0.1 ONBOOT=yes DNS1=205.134.232.138 DNS2=4.4.4.4 DEVICE=eth0:0 BOOTPROTO=static BROADCAST=192.168.0.255 HWADDR=00:0C:29:1E:DE:86 IPADDR=192.168.0.240 NETMASK=255.255.255.0 NETWORK=192.168.0.0 ONBOOT=yes # /etc/init.d/network restart Shutting down interface eth0: Device state: 3 (disconnected) [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK Bringing up interface eth0: Active connection state: activated Active connection path: /org/freedesktop/NetworkManager/ActiveConnection/3 [ OK ] # ping 192.168.0.240 PING 192.168.0.240 (192.168.0.240) 56(84) bytes of data. From 192.168.0.242 icmp_seq=2 Destination Host Unreachable Appreciate any advice, thanks Update: Perhaps this is relevant? On CentOS 5.7: # dmesg |grep eth eth0: registered as PCnet/PCI II 79C970A eth0: link up eth0: link up On 6.3: # dmesg | grep eth e1000 0000:02:00.0: eth0: (PCI:66MHz:32-bit) 00:0c:29:1e:de:86 e1000 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None 8021q: adding VLAN 0 to HW filter on device eth0 eth0: no IPv6 routers present

  Read the article

• Debian 7: "Failure of key exchange and association"

  - by pyrogoggles

  I'm installing Debian using the Live CD with GNOME and the non-free packages. The internet works just fine when using the live CD, but when you try to open the installer and select a network, it gives me the error of "Failure of key exchange and association". I've put everything in right, and tried multiple times. However, it never works. Am I just going to have to use ethernet to install? Thanks, people.

  Read the article

• Cannot access a very specific site from my router

  - by DJDarkViper

  This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

  Read the article

• Again WPA Connection problem even after changed to latest version ..please help

  - by Renjith G

  I am using hostapd, wireless tools with madwifi for my wireless ap in my board. The WEP, WPA-PSK connections and communications between my board with linux and my desktop PC, Windows XP SP2 (with Olitec USB wireless) are fine. But when I configured the WPA type, the connection seems established but shows the status "TKIP - Key Absent" in the security dialog box. Anyone faced this problem? Am attaching the conf files and the connection status. In the AP side am complaining . I am using the in built radius server conf with the hostapd 0.4.7 hostapd.conf interface=ath0 driver=madwifi logger_syslog=0 logger_syslog_level=0 logger_stdout=0 logger_stdout_level=0 debug=0 eapol_key_index_workaround=1 dump_file=/tmp/hostapd.dump.0.0 ssid=Renjith G wpa wpa=1 wpa_passphrase=mypassphrase wpa_key_mgmt=WPA-EAP wpa_pairwise=TKIP CCMP wpa_group_rekey=600 macaddr_acl=2 /* commented */ ieee8021x=1 /* commented */ eap_authenticator=1 own_ip_addr=172.16.25.1 nas_identifier=renjithg.com auth_server_addr=172.16.25.1 auth_server_port=1812 auth_server_shared_secret=key1 ca_cert=/flash1/ca.crt server_cert=/flash1/server.crt eap_user_file=/etc/hostapd.eap_user hostapd.eap_user "*@renjithg.com" TLS And the commands am using are wlanconfig ath0 create wlandev wifi0 wlanmode ap iwconfig ath0 essid Renjith channel 6 ifconfig ath0 192.168.25.1 netmask 255.255.255.0 up hostapd -ddd /etc/hostapd.conf Please correct if am wrong .. Also am getting the debug messages on my AP when am connecting in my windows machine through WPA ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf Configuration file: /etc/hostapd.conf Line 18: obsolete eap_authenticator used; this has been renamed to eap_server madwifi_set_iface_flags: dev_up=0 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'Renjith G wpa' madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA= 0x1 madwifi_set_iface_flags: dev_up=1 madwifi_set_privacy: enabled=1 WPA: group state machine entering state GTK_INIT GMK - hexdump(len=32): 9c 77 cd 38 5a 60 3b 16 8a 22 90 e8 65 b3 c2 86 40 5c be c3 dd 84 3e df 58 1d 16 61 1d 13 d1 f2 GTK - hexdump(len=32): 02 78 d7 d3 5d 15 e3 89 9c 62 a8 fe 8a 0f 40 28 ba dc cd bc 07 f4 59 88 1c 08 84 2b 49 3d e2 32 WPA: group state machine entering state SETKEYSDONE madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 Deauthenticate all stations l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 < Register Fail < Register Fail Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 NOW am getting the following error message with latest tools. *This is the latest error messages..please refer this only..* ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf TLS: Trusted root certificate(s) loaded madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'RenjithGwpa' SSID - hexdump_ascii(len=11): 52 65 6e 6a 69 74 68 47 77 70 61 RenjithGwpa PSK (ASCII passphrase) - hexdump_ascii(len=12): 6d 79 70 61 73 73 70 68 72 61 73 65 mypassphrase PSK (from passphrase) - hexdump(len=32): a6 55 3e 76 94 8b d9 81 a1 22 5e 24 29 83 33 86 11 a8 7e 93 19 7c a9 ab ab cc 12 58 37 e5 35 b6 RADIUS local address: 172.16.25.1:1024 madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA=0x1 WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 madwifi_set_iface_flags: dev_up=1 ath0: Setup of interface done. l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8b1a len=24 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09

  Read the article

• Why does the file date always change to the current date?

  - by Marshall

  We are a programming shop, but this i snot a programming question. My boss has put an external HD on the network. It contains the 'home' folders for users on the network. He uses it to place VB projects that he wants me to work on. But no matter what date and time he places a project on the drive, the file dates(modified) always shows the current date, though nothing in the files have changed. It makes it very hard to confirm that he has given me the latest versions. (He is not a fan of version control and nothing I do will convince him different.) Any ideas why this happens and how to prevent it from happening? P.S. As I wrote this I decided to add the last accessed date to the file display, and those dates happen to show the dates I expect to see. Why is the modified date getting changed, but not the accessed date. Does the accessed date change only when the files are opened or read, changed or not? Note: I use Directory Opus 9, a replacement for windows file browser. Thanks, Marshall

  Read the article

• Problem with Lenovo x200s Wifi under Ubutu Karmic

  - by oneself

  Hi, I have just gotten my Lenovo X200s laptop, and I am install Ubuntu 9.10 Karmic on it. The installation went through without a hitch, but I can't get my wifi to work. lspci | grep Network Produces the following results: 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10) The weird part is that when I turn the wifi hardware stitch on and off on the side of the laptop, I get the following printed in /var/log messages: Dec 30 23:24:48 temp-laptop kernel: [ 213.432302] usb 4-2: USB disconnect, address 2 Dec 30 23:24:52 temp-laptop kernel: [ 217.276310] usb 4-2: new full speed USB device using uhci_hcd and address 3 Dec 30 23:24:52 temp-laptop kernel: [ 217.441759] usb 4-2: configuration #1 chosen from 1 choice Does Ubuntu think my wifi card is a USB device? Am I missing some driver? What can I do to fix this? Please, help!

  Read the article

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

  - by Elliot.Bradshaw

  I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

  Read the article

• What's the difference between a wifi access point and station?

  - by Earlz

  I noticed that my (rooted) modem has some hidden modes for wifi. It has the default(and only setting without rooting) wireless access point, but it also has the settings repeater, ad-hoc, and station. What I'm really curious about is this station mode and how it differs from access point. I did a cursory search and didn't come up with any significant differences, other than that they are two distinct modes on many wireless chipsets. What is this station mode and how does it differ from access point?

  Read the article

• Data transfer to my own computer from a website host by the same computer

  - by gunbuster363

  Hi all, I have a question about using a web site host in my computer, say Computer A, using any web server hosting application e.g : apache. I connect to my website in my very same computer A, and request to download a file of size 1Mb, in otherwords, I am connecting to my own computer and want to download a file in my computer. In addition, my internet access is bound by a proxy server in a way of gateway. The questions are - does the file transfer really exist? Or is it a local file copying between 2 location? Will my data packet go through the proxy, to the internet, and go back to the proxy and return to me? Thanks everyone who are watching this question.

  Read the article

• SOHO NETGEAR wireless router disconnects when downloading torrents

  - by Lirik

  I have a NETGEAR WGT624 router at home which dies when there is a heavy torrent load. I open up my torrent client and it downloads for about 5 to 10 minutes and it continues to increase the number of seeds (goes up to 70-80 seeds), but after that the router simply fails and I have to restart it in order to get an internet connection again. Is there any way that I can fix this? New router firmware? Change some router options? Feed it a cookie? Anything?

  Read the article

• Top ten security tips for non-technical users

  - by Justin

  I'm giving a presentation later this week to the staff at the company where I work. The goal of the presentation is to serve as a refresher/remidner of good practices that can help keep our network secure. The audience is made up of both programmers and non-technical staff, so the presentation is geared for non-technical users. I want part of this presentation to be a top list of "tips". The list needs to be short (to encourage memory) and be specific and relevant to the user. I have the following five items so far: Never open an attachment you didn't expect Only download software from a trusted source, like download.com Do not distribute passwords when requested via phone or email Be wary of social engineering Do not store sensitive data on an FTP server Some clarifications: This is for our work network These need to be "best practices" tips for the end-user, not IT policy We have backups, OS patches, firewall, AV, etc, all centrally managed This is for a small business (less than 25 people) I have two questions: Do you suggest any additional items? Do you suggest any changes to existing items?

  Read the article

• One email user keeps disconnecting from our exchange server

  - by Funky Si

  I have one user who keeps reporting that Outlook keeps disconnecting from our email server. All other users are fine. Our email server is running Exchange 2010 and the client is running Outlook 2003. The disconnection only lasts a moment. I have checked for logs on the client and Exchange server and can not see any reason for the disconnect, On the Client I get EventId 26 telling me Outlook has disconnected and reconnected but no reason why. Can anyone give me some suggestions of things to try and track down where the problem could be? --Update-- I have found the following log file C:\Program Files\Microsoft\Exchange Server\V14\Logging\RPC Client Access which suggests that it is a problem with RPC sessions. Excerpt is below 2013-01-31T15:21:24.015Z,6413,15,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,0,00:00:00,"BS=Conn:24,HangingConn:0,AD:$null/$null/0%,CAS:$null/$null/2%,AB:$null/$null/0%,RPC:$null/$null/1%,FC:$null/0,Policy:ClientThrottlingPolicy2,Norm[Resources:(Mdb)Mailbox Database 0765959540(Health:-1%,HistLoad:0),(Mdb)Public Folder Database 1945427388(Health:-1%,HistLoad:0),];GC:6/1/0;", 2013-01-31T15:21:24.015Z,6413,16,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,PublicLogoff,0,00:00:00,LogonId: 1, 2013-01-31T15:21:24.015Z,6413,16,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,"BS=Conn:24,HangingConn:0,AD:$null/$null/0%,CAS:$null/$null/2%,AB:$null/$null/0%,RPC:$null/$null/1%,FC:$null/0,Policy:ClientThrottlingPolicy2,Norm[Resources:(Mdb)Mailbox Database 0765959540(Health:-1%,HistLoad:0),(Mdb)Public Folder Database 1945427388(Health:-1%,HistLoad:0),];GC:6/1/0;", 2013-01-31T15:21:24.015Z,6417,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,OwnerLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.015Z,6417,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,0x6BA (rpc::Exception),00:02:54.7668000,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0; SessionDropped,"RpcEndPoint: [ServerUnavailableException] Connection must be re-established - [SessionDeadException] Connection doesn't have any open logons, but has client activity. This may be masking synchronization stalls. Dropping a connection." 2013-01-31T15:21:24.015Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,DelegateLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00.0156000,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, 2013-01-31T15:21:24.031Z,6420,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,Disconnect,0,00:02:54.2364000,, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,OwnerLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, 2013-01-31T15:21:24.031Z,6419,5,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,Disconnect,0,00:02:54.4392000,, 2013-01-31T15:21:24.031Z,6416,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,DelegateLogoff,0,00:00:00,LogonId: 0, 2013-01-31T15:21:24.031Z,6416,7,/o=EUROSAFEUK/ou=first administrative group/cn=Recipients/cn=andy,,OUTLOOK.EXE,11.0.8303.0,Classic,,,ncacn_ip_tcp,,,,00:00:00,Budget Highs [AD = 0][CAS = 3][RPC = 1] Session Throttled Count = 0, Can anyone help point me in the right direction for a solution?

  Read the article

• Displaying ads over WiFi hotspot

  - by Ahsan

  I have recently distributed my WiFi network with highpseed antennas to my area which covers almost 300-400 peoples. I am not charging them anything but i would like to generate some revenue through Advertisements placed on the websites that they visit. Is it possible to display ads from Google (I know i can do redirect the Advertisements, using some cache server or firewall) . Its just like a free vpn but i would like to have my advertisements above the websites they visit so i can take out the cost for the WiFi that i offer. Any suggestions would be great!

  Read the article

• Other user SSHed from my hardware

  - by Alex

  While logged into our HPC cluster I used w to check out who else was logged in. I happened to notice that it looks like there's another user logged in from my (personal) computer; 19:04:47 up 40 days, 6:39, 44 users, load average: 0.10, 0.14, 0.18 USER TTY FROM LOGIN@ IDLE JCPU PCPU WHAT ME pts/4 zerg.neuron12. 18:55 0.00s 0.09s 0.04s w SOMEONE_ELSE pts/35 zerg.neuron12. Sat14 2:27m 0.08s 0.08s -bash Is this something I should be worried out - I tried to kill the other session but had a permission denied message. Is it possible we just both have the same hardware name? I'd have thought that if this were the case the server would give one of us a different name (e.g. zerg1) when we logged in to prevent confusion. This is not an area I have any experience with, so any advice would be greatly appreciated!

  Read the article

• Network / Internet diagnostic tool to locate an error?

  - by Jesper

  Hi, I’m facing some difficulties with the Internet / network at my work and I have trouble locating the precise error and when and how it occurs. The problem is that the client machines in the house sporadic is disconnected to the Internet. I’m some what new so I haven’t that much inside in the network and apparently neither has my predecessor. What I am requesting and hoping you guys knows about is, if there exist some kind of network monitor tool I can install and run and it will periodically check the network, the Internet connection etc. and record to logs. Then, if there suddenly arises a problem some time of the day in some part of the network or the Internet connection, I can check it perhaps the next day. I’ve just downloaded and installed Microsoft Network Monitor 3.3 application and hopeful it can give me some answers on where the instability is located but I still would like a tool to make different checks and test in some time interval. Do anyone know about such a program or another kind of performance / diagnostic tool / method I can use? Sincere Jesper

  Read the article

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• Two Network Adapters on Hyper-V Host - Best way to configure?

  - by GoNorthWest

  Hi, I have two physical network adapters installed in my Hyper-V host. I want one to be dedicated to the host, and the other to provide external network services to the VMs. Would the appropriate configuration be as such: Leave the first physical network adapter alone, assigning it the host IP, but not using it to create any Virtual Netorks For the second physical adapter, I would create an External Network, along with a Microsoft Virtual Switch, and use that to provide network services to the VMs. Each virtual NIC for the VM would be associated with that External Network. A static IP would be assigned to this adapter, and each VM would be assigned a static IP as well. The above seems reasonable to me, but I'm not sure if it's correct. Does anyone have any thoughts? Thanks! Mark

  Read the article

• Slow transfer speed between two servers

  - by Linux Guy

  I have two servers both network cards speed is 10Gbps The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.1 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.1, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.0 port 38895 connected with 0.0.0.1 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service the connection will be ok , after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• What's the difference between RDP vs VNC ?

  - by Jonathan

  Okay I was playing around with the iPhone Jaadu App and I realized I download the wrong desktop client. So what's really the difference between the RDP and VNC? (because there is Jaadu RDP and Jaadu VNC 2 different app) They both provide the same function? features ?

  Read the article

• Linux Transparent Bridge for Network

  - by Blackninja543

  I am attempting to set up a semi-transparent bridge. I say semi because I want it to act as a transparent tap for all traffic moving through both sides of the bridge. What I also want is to have the "green zone" accessible to a web interface for the bridge that will display all results of the IDS and other network monitoring tools. My example would be as such: eth0 <--> bridge(br0) <--> eth1 The entire network would be on the same subset however anything coming from eth0 to eth1 would be accepted. The only time anything would be drop is if the eth0 attempted to access br0. If someone attempts to access the web interface on br0 through eth1 it will succeed. My biggest problem I feel is if I attempt to block anything from eth0 to br0 this will drop the bridge all together.

  Read the article

• Rate limit a wireless interface

  - by Jamie Hankins

  I have access to my routers SSH and IPTables. I want to rate limit my guest network to 1Mb/s so they can't guzzle my bandwidth. rai1 RTWIFI SoftAP ESSID:"GuestNetwork" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi0 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F8 Bit Rate=300 Mb/s wdsi1 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi2 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s wdsi3 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s I'm just wondering the command I need to limit it. I tried the iwconfig limit command but it failed. Thanks

  Read the article

• Weird Network Behavior of Home Router

  - by Stilgar

  First of all I would like to apologize because what you are going to read will be long and confusing but I am fighting this issue for 3 days now and am out of ideas. At home I have the following setup 50Mbps Internet connects into a home router A 2 desktop computers connect to router A via standard FTP LAN cables including one where the cable is ~20m long. a second router B connects to router A via standard FTP LAN cable X (~20m long). several devices connect to the wireless network of router B and there are a couple of desktop computers connected to it through FTP LAN cables. For some reason computers connected to router B when it is connected via cable X have very slow Internet connection. It is like 5 times slower than what is expected. This is the actual problem I am trying to solve. Interesting facts If a computer is connected to cable X directly instead of through router B the Internet speed is just fine (up to the 50Mbps I get from the ISP). Tested with two computers. I have tried replacing router B with another router C and the problem persists. If I connect router B via another cable to the same ports with the same settings everything seems to work fine and computers connected to router B have quite fast Internet I have tested mainly via Speedtest.net but I have also achieved similar speeds when downloading a file The upload speed is quite higher than the download speed in all cases. Note that my ISP usually has higher upload speed (unless it manages to hit the 50Mbps cap) It seems like the speed when connecting through router B with cable X is reduced 4-5 times no matter what the original speed is. For example via router B I get 10Mbps speed to local servers where I get 50Mbps when connected on router A. If I use a distant server where the ISP is only able to provide 25Mbps I get 4-5Mbps on router B. WiFi is slower than LAN on both routers (which is normal) but the reduced speed is reduced proportionally for WiFi. In addition the upload speed is normally higher from the ISP and it is also reduced proportionally. I have tried two different network configurations. One where I have NAT behind NAT where router B connects to router A via the WAN port and has its own DHCP. Second where router B connects to router A via standard LAN port and has DHCP disabled. In this configuration router B serves as a switch and the Network Gateway for computers connected to router B is the internal IP address of router A. Both configurations work just fine but both manifest the reduced speed issue. pings seem to work just fine As far as I can tell none of the cables is crossed The RJ45 setup for cable X orange orange-white brown brow-white blue blue-white green green-white This is a big problem for me since cable X passes through walls and floors and is very hard to replace. I also may have gotten some of the facts wrong because I am almost going crazy with this issue and testing includes going several floors up and down the staircase. One hypothesis I came up with is that the cable is defective in such a way that the voltage from the router affects its performance. When it is connected to a computer it performs just fine but the router has less power. Related hypothesis includes the cable being affected by electricity cables in the walls when the voltage is low. (I know nothing about electricity) So any ideas what to do, what to test or what the issue may be?

  Read the article

• 2 nics. 2 Defaults Gateways

  - by andre.dias

  Here is my scenario: i have this server with 2 nics, each one with different IPs, connected to differents routers. Almost everything is configured whe way i need. Traffic coming from eth0 exits using eth0, traffic coming from eth1 exits using eth1. And there is a default gateway configured. $route: default IP 0.0.0.0 UG 0 0 0 eth0 With this configuration, the traffic generated in the server is going out using eth0 (lynx www.google.com for example). The problem is: the Internet link from eth0 went down today. The traffic coming from eth1 was ok...no problem. But the traffic generated in the server was a problem...the default gateway was out...no access do the Internet anymore (no more lynx www.google.com) So i added a new default gateway configuration, pointing to eth1. For 30 minutes i kept that way...2 default gateways, but just one was "working"...and everything was working just fine. But then i removed de eth0 gateway entry because, well, 2 default gateways is kind of weird. My question: is there any problem on keeping these 2 default gateways, one for each? So i don´t need to do nothing when one link go down again? $route: default IP1 0.0.0.0 UG 0 0 0 eth0 default IP2 0.0.0.0 UG 0 0 0 eth1

  Read the article

• correct routing for multiple devices

  - by helmi

  I have Debian Lenny machine with 3 interfaces enabled (eth0-2), and I have problems as follow. eth1 is connected to a router and this router has portforwarding for port80. eth2 is connected direct to the internet If I open a website hosted on my system via the router it works fine. If I try to open the same via the eth2 connetion it does not! tshark shows incomming trafic on eth2 but nothing goes out there. iptabes accepts all My routing table: Ziel Router Genmask Flags Metric Ref Use Iface 10.9.0.2 * 255.255.255.255 UH 0 0 0 tun0 212.236.24.128 * 255.255.255.224 U 0 0 0 eth2 192.168.1.0 * 255.255.255.0 U 0 0 0 eth1 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 10.9.0.0 10.9.0.2 255.255.255.0 UG 0 0 0 tun0 default 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 default 212.236.024.129 0.0.0.0 UG 0 0 0 eth2 default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >