Search Results

Search found 46419 results on 1857 pages for 'web traffic'.

Page 129/1857 | < Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >

  • How to redirect all Internet traffic to OpenVPN Server

    - by JuliaS
    I have seen working solutions around the issue of forcing Internet traffic to go through the OpenVPN server but they are all done in Linux, all I want to know is how to add an entry to the route table in windows to make this happen. connectivity between the client and server is fine, my Windows 7 client can establish a connection to the Windows 2008 Server, but when established Internet traffic is still going from the local Windows 7 machine. Here are the details: Server: Windows 2008 Server with one NIC OpenVPN IP Address: 192.168.0.1 Local NIC IP Address (connects the server to the Internet): 10.242.69.107 Client: Windows 7 with one NIC OpenVPN IP Address: 192.168.0.2 ISP allocated IP Address: 10.0.8.2 (gateway 10.0.8.1) Server OpenVPN Config: dev tun ifconfig 192.168.0.1 192.168.0.2 secret static.key push "redirect-gateway def1" Client OpenVPN Config: remote xxx.xxx.com dev tun ifconfig 192.168.0.2 192.168.0.1 secret static.key I'm not an expert with adding routes...etc. I would be grateful if someone could let me know how to add this entry in my server/client route table. EDIT: Output from the client's netstat -rnv IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.0.8.1 10.0.8.2 20 10.0.8.0 255.255.255.252 On-link 10.0.8.2 276 10.0.8.2 255.255.255.255 On-link 10.0.8.2 276 10.0.8.3 255.255.255.255 On-link 10.0.8.2 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.252 On-link 192.168.0.2 286 192.168.0.2 255.255.255.255 On-link 192.168.0.2 286 192.168.0.3 255.255.255.255 On-link 192.168.0.2 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.8.2 276 224.0.0.0 240.0.0.0 On-link 192.168.0.2 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.8.2 276 255.255.255.255 255.255.255.255 On-link 192.168.0.2 286 ===========================================================================

    Read the article

  • How to force certain traffic through GRE tunnel?

    - by wew
    Here's what I do. Server (public internet is 222.x.x.x): echo 'net.ipv4.ip_forward=1' >> /etc/sysctl.conf sysctl -p iptunnel add gre1 mode gre local 222.x.x.x remote 115.x.x.x ttl 255 ip add add 192.168.168.1/30 dev gre1 ip link set gre1 up iptables -t nat -A POSTROUTING -s 192.168.168.0/30 -j SNAT --to-source 222.x.x.x iptables -t nat -A PREROUTING -d 222.x.x.x -j DNAT --to-destination 192.168.168.2 Client (public internet is 115.x.x.x): iptunnel add gre1 mode gre local 115.x.x.x remote 222.x.x.x ttl 255 ip add add 192.168.168.2/30 dev gre1 ip link set gre1 up echo '100 tunnel' >> /etc/iproute2/rt_tables ip rule add from 192.168.168.0/30 table tunnel ip route add default via 192.168.168.1 table tunnel Until here, all seems going right. But then 1st question, how to use GRE tunnel as a default route? Client computer is still using 115.x.x.x interface as default. 2nd question, how to force only ICMP traffic to go through tunnel, and everything else go default interface? I try doing this in client computer: ip rule add fwmark 200 table tunnel iptables -t mangle -A OUTPUT -p udp -j MARK --set-mark 200 But after doing this, my ping program will timeout (if I not doing 2 command above, and using ping -I gre1 ip instead, it will works). Later I want to do something else also, like only UDP port 53 through tunnel, etc. 3rd question, in client computer, I force one mysql program to listen on gre1 interface 192.168.168.2. In client computer, there's also one more public interface (IP 114.x.x.x)... How to forward traffic properly using iptables and route so mysql also respond a request coming from this 114.x.x.x public interface?

    Read the article

  • Network Traffic Log

    - by Chris Becke
    Background - On my "home" network I have a Linksys WTR45GL router providing my internet access as well as a wireless AP. Connected I have * 2 Windows PCs (wired) * At least one laptop (Wired) * Some 802.11 enabled handheld consoles (PSPs) * A Nintendo Wii * Some windows XP pcs used by the people in the granny flat. Where I live, South Africa, well, 1Gb worth of monthly cap is, while not expensive, costly enough that I'd like to be sure that all the bandwidth used by devices on my network is ... well ... legitimate and not the result of neighbors parasiting my wireless, malware or just the result of "liberal" download policies in my software. I got the Linksys WRT45GL on the understanding that there were custom firmwares (DD-WRT and Tomato) that allowed bandwidth tracking, but there doesn't seem to be any facility to get a log of traffic that can be examined to see (a) which local devices were the biggest consumers of bandwidth and (b) what they were connected to. What tools are there for logging traffic such that, when it gets to that OMG moment in the month when all my bandwidth is gone, I have a chance to find out what the hell used it all up (and hopefully attempt some corrective action).

    Read the article

  • Outside VPN traffic not able to ping site-to-site VPN remote site

    - by Siriss
    we have two ASA 5510s running 8.4 in a site-to-site VPN setup. All internal traffic is working smoothly. Site/Subnet A: 192.100.0.0 - local Site/Subnet B: 192.200.0.0 - remote VPN Users: 192.100.40.0 - assigned by ASA When you VPN into the network, all traffic hits Site A, and everything on subnet A is accessible. Site B however, is completely inaccessible for VPN users. All machines on subnet B, the firewall itself, etc... is not reachable by ping or otherwise. I know I am missing a NAT rule, and in 8.2, it was easy as pie to setup using ASDM, but now I can't get it for the life of me as 8.4 apparently made a lot of changes to NAT rules. I am not too comfortable in the ASA command line, but if there is a command I need to add or if you could direct me where I can add this in 8.4 ASDM I would really appreciate it. I have tired NAT Exempt, Static NAT, Static NAT Policies, etc... I think I tried all the options. I also might have my interfaces confused with the new look at feel of ASDM. Thank you much in advance and I hope I have been thorough enough.

    Read the article

  • Route traffic from one VPN to a second VPN

    - by Dominic
    I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

    Read the article

  • Route all traffic via OpenVPN client

    - by Ilya
    I've got OpenVPN client running on 192.168.0.3. What I'd like to do is route all the traffic from the second computer with 192.168.0.100 via OpenVPN client that's running on the first computer. My router ip is 192.168.0.1 Network topology: Windows computer with OpenVPN client: 192.168.0.3 Windows computer whose traffic has to be rerouted: 192.168.0.100 Router: 192.168.0.1 I want it to work in the following way: 192.168.0.100 computer => 192.168.0.3 computer => OpenVPN => 192.168.0.1 How can I achieve that by only modifying windows' routing table? I've tried entering the following into windows shell(on computer without VPN), which didn't work (it just dropped my internet connection): route delete 0.0.0.0 mask 255.255.255.255 192.168.0.1 route add 0.0.0.0 mask 255.255.255.255 192.168.0.3 Should I also setup the computer that has OpenVPN client running? Does it have anything to do with windows tcp forwarding? Thanks!

    Read the article

  • Force local IP traffic to an external interface

    - by calandoa
    I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

    Read the article

  • IP Blacklists and suspicious inbound and outbound traffic

    - by Pantelis Sopasakis
    I administer a web server and recently we had our IP banned (!) from our host after they received a notification e-mail for abuse. In particular our server is allegedly involved in spam attacks over HTTP. The content of the abuse report email we received was not much informative - for example the IP addresses our server is supposed to have attacked against are not included - so I started a wireshark session checking for suspicious traffic over TCP/HTTP while trying to locate possible security holes on the system. (Let me note that the machine runs a Debian OS). Here is an example of such a request... Source: 89.74.188.233 Destination: 12.34.56.78 // my ip Protocol: HTTP Info: GET 'http://www.media.apniworld.com/image.php?type=hv' HTTP/1.0 I manually blacklisted this host (as well as some other ones) blocking them with iptables, but I can't keep on doing manually all day long... I'm looking for an automated way to block such IPs based on: Statistical analysis, pattern recognition or other AI-based analysis (Though, I'm reluctant to trust such a solution, if exists) Public blacklists Using DNSBL I actually found out that 89.74.188.233 is blacklisted. However other IPs which are strongly suspicious like 93.199.112.126 (i.e. http://www.pornstarnetwork.com/account/signin), unfortunately were not blacklisted! What I would like to do is to automatically connect my firewall with DNSBL (or some other blacklist database) and block all traffic towards blacklisted IPs or somehow have my local blacklist automatically updated.

    Read the article

  • Route all wlan0 traffic over tun0

    - by Tuinslak
    I'm looking for a way to route all wlan0 traffic (tcp and udp) over tun0 (openvpn). However, all other traffic originating from the device itself should not be routed through tun0. I'm guessing this could be realized using iptables or route, but none of my options seem to work. # route add -net 0.0.0.0 gw 172.27.0.1 dev wlan0 SIOCADDRT: No such process Info: This is because the VPN server is not redundant, and wlan users are not really important. However, all services running on the device are fairly important and having a VPN virtual machine with no SLA on it is just a bad idea. Trying to minimize the odds of something going wrong. So setting the VPN server as default gateway is not really an option. I also want all wlan0 user to use the VPN server's IP address as external IP. Edit with the script provided: root@ft-genesi-xxx ~ # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.27.0.17 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.13.37.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 172.27.0.0 172.27.0.17 255.255.192.0 UG 0 0 0 tun0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 root@ft-genesi-xxx ~ # ./test.sh RTNETLINK answers: No such process root@ft-genesi-xxx ~ # cat test.sh #!/bin/sh IP=/sbin/ip # replace with the range of your wlan network, or use fwmark instead ${IP} rule add from 10.13.37.0/24 table from-wlan ${IP} route add default dev tun0 via 127.72.0.1 table from-wlan ${IP} route add 10.13.37.0/24 dev wlan0 table from-wlan

    Read the article

  • Route return traffic to correct gateway depending on service

    - by Marnix van Valen
    On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

    Read the article

  • Sharepoint web part fails intermittently

    - by pringly
    I have a MOSS 2007 environment, 2 web servers and a DB server, load balanced between the two web servers. I deployed a web part recently, which worked fine for a while, but failed on web server 2 after a day. When it fails, it gets the error message: 'A Web Part or Web Form Control on this Page cannot be displayed or imported. The type could not be found or it is not registered as safe’ Once it has failed, it will stay that way until an IIS reset is done. The other web server never fails, I tried to force the second web server to fail to recreate the issue and have been unable to do it. I tried placing it under heavy http traffic and it handled it fine. Put it back in the pool and it failed again after about 7 hours. So, if i remove the .dll for the webpart from the affected web server, the webpart doesnt stop working. Is this normal behavior? I checked the bin directory for the site and the global assembly and it there is no other copy of the .dll anywhere else on the server. Also, when checking the web part gallery, if the web part has failed it will appear in the gallery, but by trying to add a new webpart, the .dll wont be listed. I have no idea how to continue troubleshooting from here or even fix it, any ideas?

    Read the article

  • PHP Web Services - Nice try

    Thanks to the membership in the O'Reilly User Group Programme the Mauritius Software Craftsmanship Community (short: MSCC) recently received a welcome package with several book titles. Among them is the latest publication of Lorna Jane Mitchell - 'PHP Web Services: APIs for the Modern Web'. Following is the book review I put on Amazon: Nice try! Initially, I was astonished that a small book like 'PHP Web Services' would be able to cover all the interesting topics about APIs and Web Services, independently whether they are written in PHP or not. And unfortunately, the title isn't able to stand up to the readers (or at least my) expectations. Maybe as a light defense, there is no usual paragraph about the intended audience of that book, but still I have to admit that the first half (chapters 1 to 8) are well written and Lorna has her points on the various technologies. Also, the code samples in PHP are clean and easy to understand. With chapter 'Debugging Web Services' the book started to change my mind about the clarity of advice and the instructions on designing and developing good APIs. Eventually, this might be related to the fact that I'm used to other tools since years, like Telerik Fiddler as HTTP proxy in order to trace and inspect any kind of request/response handling. Including localhost monitoring, SSL certification acceptance, and the ability to debug mobile devices, especially iOS-based ones. Compared to Charles, Fiddler is available for free. What really got me off the hook is the following statement in chapter 10 about Service Type Decisions: "For users who have larger systems using technology stacks such as Java, C++, or .NET, it may be easier for them to integrate with a SOAP service." WHAT? A couple of pages earlier the author recommends to stay away from 'old-fashioned' API styles like SOAP (if possible). And on top of that I wonder why there are tons of documentation towards development of RESTful Web Services based on WebAPI. The ASP.NET stack clearly moves away from SOAP to JSON and REST since years! Honestly, as a software developer on the .NET stack this leaves a mixed feeling after all. As for the remaining chapters I simply consider them as 'blah blah' without any real value and lots of theoretical advice. Related to the chapter 13 about 'Documentation', I just had the 'pleasure' to write a C#-based client against a Java-based SOAP Web Service. Personally, I take the WSDL as the master reference in the first place and Visual Studio generates all the stub types involved in the communication. During the implementation and testing I came across a 'java.lang.NullPointerException' in various methods and for various method parameters. The WSDL and the generated types were declared as Nullable, so nothing to worry about, or? Well, I logged in a support ticket, and guess what was the response to that scenario? "The service definition in the WSDL is wrong, please refer to the documentation in order to use the methods and parameters correctly" - No comment! Lorna's title is a quick read and in some areas she has good advice on designing and implementing Web Services and APIs. But roughly 100 pages aren't enough to cover a vast topic like that. After all, nice try and I'm looking forward to an improved second edition. Honestly, I never thought that I would come across a poor review. In general, it's a good book but it clearly has a lack of depth, the PHP code samples are incomplete (closing tags missing), and there are too many assumptions and theoretical statements.

    Read the article

  • Migrating SQL Server Compact Edition (SQL CE) database to SQL Server using Web Matrix

    - by Harish Ranganathan
    One of the things that is keeping us busy is the Web Camps we are delivering across 5 cities.  If you are a reader of this blog, and also attended one of these web camps, there is a good chance that you have seen me since I was there in all the places, so far.  The topics that we cover include Visual Studio 2010 SP1, SQL CE, ASP.NET MVC & HTML5.  Whenever I talk about SQL CE, the immediate response is that, people are wow that Microsoft has shipped a FREE compact edition database, which is an embedded database that can be x-copy deployed.  If you think, well didn’t Microsoft ship SQL Express which is FREE?  The difference is that, SQL Express runs as a service in the machine (if you open SQL Configuration Manager, you can notice that SQL Express is running as a service along with your SQL Server Engine (if you have installed ).  This makes it that, even if you are willing to use SQL Express when you deploy your application, it needs to be installed on the production machine (hosting provider) and it needs to run as a service.  Many hosters don’t allow such services to run on their space. SQL CE comes as a x-Copy deploy-able database with just a few DLLs required to run it on the machine and they don’t even need to be installed in GAC on the production machine.  In fact, if you have Visual Studio 2010 SP1 installed, you can use the “Add Deployable Dependencies” option in Project-Properties and it would detect that SQL CE is something you would probably want to add as a deploy-able dependency for your project.  With that, it bundles the required DLLs as a part of the “_bin_deployableAssemblies” folder.  So your project can be x-Copy deployed and just works fine. However, SQL CE has the limit of 4GB storage space.  Real world applications often require more than just 4GB of data storage and it often turns out that people would like to use SQL CE for development/ramp up stages but would like to migrate to full fledged SQL Server after a while.  So, its only natural that the question arises “How do I move my SQL CE database to SQL Server”  And honestly, it doesn’t come across as a straight forward support.  I was talking to Ambrish Mishra (PM in SQL CE Team, Hyderabad) since I got this question in almost all the places where we talked about SQL CE.   He was kind enough to demonstrate how this can be accomplished using Web Matrix.  Open Web Matrix (Web Matrix can be installed for free from www.microsoft.com/web) and click on “Site from Template” Click on the “Bakery” template (since by default it uses a SQL CE database and has all the required sample data) and click “Ok”. In the project, you can navigate to the Database tab and will be able to find that the Bakery site uses a SQL CE database “bakery.sdf” Select the “bakery.sdf” and you will be able to see the “Migrate” button on the top right Once you click on the “Migrate” button, you will notice that the popup wizard opens up and by default is configured for SQL Express.  You can edit the same to point to your local SQL Server instance, or a remote server. Upon filling in the Server Name, Username and Password, when you click “Ok”, couple of things happen.  1. The database is migrated to SQL Server (local or remote – subject to permissions on remote server).   You can open up SQL Server Management Studio and connect to the server to verify that the “bakery” database exists under “Databases” node. 2. You can also notice that in Web Matrix, when you navigate to the “Files” tab and open up the web.config file, connection string now points to the SQL Server instance (yes, the Migrate button was smart enough to make this change too ) And there it is, your SQL Server Compact Edition database, now migrated to SQL Server!! In a future post, I would explain the steps involved when using Visual Studio. Cheers !!!

    Read the article

  • Windows Azure: General Availability of Web Sites + Mobile Services, New AutoScale + Alerts Support, No Credit Card Needed for MSDN

    - by ScottGu
    This morning we released a major set of updates to Windows Azure.  These updates included: Web Sites: General Availability Release of Windows Azure Web Sites with SLA Mobile Services: General Availability Release of Windows Azure Mobile Services with SLA Auto-Scale: New automatic scaling support for Web Sites, Cloud Services and Virtual Machines Alerts/Notifications: New email alerting support for all Compute Services (Web Sites, Mobile Services, Cloud Services, and Virtual Machines) MSDN: No more credit card requirement for sign-up All of these improvements are now available to use immediately (note: some are still in preview).  Below are more details about them. Web Sites: General Availability Release of Windows Azure Web Sites I’m incredibly excited to announce the General Availability release of Windows Azure Web Sites. The Windows Azure Web Sites service is perfect for hosting a web presence, building customer engagement solutions, and delivering business web apps.  Today’s General Availability release means we are taking off the “preview” tag from the Free and Standard (formerly called reserved) tiers of Windows Azure Web Sites.  This means we are providing: A 99.9% monthly SLA (Service Level Agreement) for the Standard tier Microsoft Support available on a 24x7 basis (with plans that range from developer plans to enterprise Premier support) The Free tier runs in a shared compute environment and supports up to 10 web sites. While the Free tier does not come with an SLA, it works great for rapid development and testing and enables you to quickly spike out ideas at no cost. The Standard tier, which was called “Reserved” during the preview, runs using dedicated per-customer VM instances for great performance, isolation and scalability, and enables you to host up to 500 different Web sites within them.  You can easily scale your Standard instances on-demand using the Windows Azure Management Portal.  You can adjust VM instance sizes from a Small instance size (1 core, 1.75GB of RAM), up to a Medium instance size (2 core, 3.5GB of RAM), or Large instance (4 cores and 7 GB RAM).  You can choose to run between 1 and 10 Standard instances, enabling you to easily scale up your web backend to 40 cores of CPU and 70GB of RAM: Today’s release also includes general availability support for custom domain SSL certificate bindings for web sites running using the Standard tier. Customers will be able to utilize certificates they purchase for their custom domains and use either SNI or IP based SSL encryption. SNI encryption is available for all modern browsers and does not require an IP address.  SSL certificates can be used for individual sites or wild-card mapped across multiple sites (we charge extra for the use of a SSL cert – but the fee is per-cert and not per site which means you pay once for it regardless of how many sites you use it with).  Today’s release also includes the following new features: Auto-Scale support Today’s Windows Azure release adds preview support for Auto-Scaling web sites.  This enables you to setup automatic scale rules based on the activity of your instances – allowing you to automatically scale down (and save money) when they are below a CPU threshold you define, and automatically scale up quickly when traffic increases.  See below for more details. 64-bit and 32-bit mode support You can now choose to run your standard tier instances in either 32-bit or 64-bit mode (previously they only ran in 32-bit mode).  This enables you to address even more memory within individual web applications. Memory dumps Memory dumps can be very useful for diagnosing issues and debugging apps. Using a REST API, you can now get a memory dump of your sites, which you can then use for investigating issues in Visual Studio Debugger, WinDbg, and other tools. Scaling Sites Independently Prior to today’s release, all sites scaled up/down together whenever you scaled any site in a sub-region. So you may have had to keep your proof-of-concept or testing sites in a separate sub-region if you wanted to keep them in the Free tier. This will no longer be necessary.  Windows Azure Web Sites can now mix different tier levels in the same geographic sub-region. This allows you, for example, to selectively move some of your sites in the West US sub-region up to Standard tier when they require the features, scalability, and SLA of the Standard tier. Full pricing details on Windows Azure Web Sites can be found here.  Note that the “Shared Tier” of Windows Azure Web Sites remains in preview mode (and continues to have discounted preview pricing).  Mobile Services: General Availability Release of Windows Azure Mobile Services I’m incredibly excited to announce the General Availability release of Windows Azure Mobile Services.  Mobile Services is perfect for building scalable cloud back-ends for Windows 8.x, Windows Phone, Apple iOS, Android, and HTML/JavaScript applications.  Customers We’ve seen tremendous adoption of Windows Azure Mobile Services since we first previewed it last September, and more than 20,000 customers are now running mobile back-ends in production using it.  These customers range from startups like Yatterbox, to university students using Mobile Services to complete apps like Sly Fox in their spare time, to media giants like Verdens Gang finding new ways to deliver content, and telcos like TalkTalk Business delivering the up-to-the-minute information their customers require.  In today’s Build keynote, we demonstrated how TalkTalk Business is using Windows Azure Mobile Services to deliver service, outage and billing information to its customers, wherever they might be. Partners When we unveiled the source control and Custom API features I blogged about two weeks ago, we enabled a range of new scenarios, one of which is a more flexible way to work with third party services.  The following blogs, samples and tutorials from our partners cover great ways you can extend Mobile Services to help you build rich modern apps: New Relic allows developers to monitor and manage the end-to-end performance of iOS and Android applications connected to Mobile Services. SendGrid eliminates the complexity of sending email from Mobile Services, saving time and money, while providing reliable delivery to the inbox. Twilio provides a telephony infrastructure web service in the cloud that you can use with Mobile Services to integrate phone calls, text messages and IP voice communications into your mobile apps. Xamarin provides a Mobile Services add on to make it easy building cross-platform connected mobile aps. Pusher allows quickly and securely add scalable real-time messaging functionality to Mobile Services-based web and mobile apps. Visual Studio 2013 and Windows 8.1 This week during //build/ keynote, we demonstrated how Visual Studio 2013, Mobile Services and Windows 8.1 make building connected apps easier than ever. Developers building Windows 8 applications in Visual Studio can now connect them to Windows Azure Mobile Services by simply right clicking then choosing Add Connected Service. You can either create a new Mobile Service or choose existing Mobile Service in the Add Connected Service dialog. Once completed, Visual Studio adds a reference to Mobile Services SDK to your project and generates a Mobile Services client initialization snippet automatically. Add Push Notifications Push Notifications and Live Tiles are a key to building engaging experiences. Visual Studio 2013 and Mobile Services make it super easy to add push notifications to your Windows 8.1 app, by clicking Add a Push Notification item: The Add Push Notification wizard will then guide you through the registration with the Windows Store as well as connecting your app to a new or existing mobile service. Upon completion of the wizard, Visual Studio will configure your mobile service with the WNS credentials, as well as add sample logic to your client project and your mobile service that demonstrates how to send push notifications to your app. Server Explorer Integration In Visual Studio 2013 you can also now view your Mobile Services in the the Server Explorer. You can add tables, edit, and save server side scripts without ever leaving Visual Studio, as shown on the image below: Pricing With today’s general availability release we are announcing that we will be offering Mobile Services in three tiers – Free, Standard, and Premium.  Each tier is metered using a simple pricing model based on the # of API calls (bandwidth is included at no extra charge), and the Standard and Premium tiers are backed by 99.9% monthly SLAs.  You can elastically scale up or down the number of instances you have of each tier to increase the # of API requests your service can support – allowing you to efficiently scale as your business grows. The following table summarizes the new pricing model (full pricing details here):   You can find the full details of the new pricing model here. Build Conference Talks The //BUILD/ conference will be packed with sessions covering every aspect of developing connected applications with Mobile Services. The best part is that, even if you can’t be with us in San Francisco, every session is being streamed live. Be sure not to miss these talks: Mobile Services – Soup to Nuts — Josh Twist Building Cross-Platform Apps with Windows Azure Mobile Services — Chris Risner Connected Windows Phone Apps made Easy with Mobile Services — Yavor Georgiev Build Connected Windows 8.1 Apps with Mobile Services — Nick Harris Who’s that user? Identity in Mobile Apps — Dinesh Kulkarni Building REST Services with JavaScript — Nathan Totten Going Live and Beyond with Windows Azure Mobile Services — Kirill Gavrylyuk , Paul Batum Protips for Windows Azure Mobile Services — Chris Risner AutoScale: Dynamically scale up/down your app based on real-world usage One of the key benefits of Windows Azure is that you can dynamically scale your application in response to changing demand. In the past, though, you have had to either manually change the scale of your application, or use additional tooling (such as WASABi or MetricsHub) to automatically scale your application. Today, we’re announcing that AutoScale will be built-into Windows Azure directly.  With today’s release it is now enabled for Cloud Services, Virtual Machines and Web Sites (Mobile Services support will come soon). Auto-scale enables you to configure Windows Azure to automatically scale your application dynamically on your behalf (without any manual intervention) so you can achieve the ideal performance and cost balance. Once configured it will regularly adjust the number of instances running in response to the load in your application. Currently, we support two different load metrics: CPU percentage Storage queue depth (Cloud Services and Virtual Machines only) We’ll enable automatic scaling on even more scale metrics in future updates. When to use Auto-Scale The following are good criteria for services/apps that will benefit from the use of auto-scale: The service/app can scale horizontally (e.g. it can be duplicated to multiple instances) The service/app load changes over time If your app meets these criteria, then you should look to leverage auto-scale. How to Enable Auto-Scale To enable auto-scale, simply navigate to the Scale tab in the Windows Azure Management Portal for the app/service you wish to enable.  Within the scale tab turn the Auto-Scale setting on to either CPU or Queue (for Cloud Services and VMs) to enable Auto-Scale.  Then change the instance count and target CPU settings to configure the Auto-Scale ranges you want to maintain. The image below demonstrates how to enable Auto-Scale on a Windows Azure Web-Site.  I’ve configured the web-site so that it will run using between 1 and 5 VM instances.  The exact # used will depend on the aggregate CPU of the VMs using the 40-70% range I’ve configured below.  If the aggregate CPU goes above 70%, then Windows Azure will automatically add new VMs to the pool (up to the maximum of 5 instances I’ve configured it to use).  If the aggregate CPU drops below 40% then Windows Azure will automatically start shutting down VMs to save me money: Once you’ve turned auto-scale on, you can return to the Scale tab at any point and select Off to manually set the number of instances. Using the Auto-Scale Preview With today’s update you can now, in just a few minutes, have Windows Azure automatically adjust the number of instances you have running  in your apps to keep your service performant at an even better cost. Auto-scale is being released today as a preview feature, and will be free until General Availability. During preview, each subscription is limited to 10 separate auto-scale rules across all of the resources they have (Web sites, Cloud services or Virtual Machines). If you hit the 10 limit, you can disable auto-scale for any resource to enable it for another. Alerts and Notifications Starting today we are now providing the ability to configure threshold based alerts on monitoring metrics. This feature is available for compute services (cloud services, VM, websites and mobiles services). Alerts provide you the ability to get proactively notified of active or impending issues within your application.  You can define alert rules for: Virtual machine monitoring metrics that are collected from the host operating system (CPU percentage, network in/out, disk read bytes/sec and disk write bytes/sec) and on monitoring metrics from monitoring web endpoint urls (response time and uptime) that you have configured. Cloud service monitoring metrics that are collected from the host operating system (same as VM), monitoring metrics from the guest VM (from performance counters within the VM) and on monitoring metrics from monitoring web endpoint urls (response time and uptime) that you have configured. For Web Sites and Mobile Services, alerting rules can be configured on monitoring metrics from monitoring endpoint urls (response time and uptime) that you have configured. Creating Alert Rules You can add an alert rule for a monitoring metric by navigating to the Setting -> Alerts tab in the Windows Azure Management Portal. Click on the Add Rule button to create an alert rule. Give the alert rule a name and optionally add a description. Then pick the service which you want to define the alert rule on: The next step in the alert creation wizard will then filter the monitoring metrics based on the service you selected:   Once created the rule will show up in your alerts list within the settings tab: The rule above is defined as “not activated” since it hasn’t tripped over the CPU threshold we set.  If the CPU on the above machine goes over the limit, though, I’ll get an email notifying me from an Windows Azure Alerts email address ([email protected]). And when I log into the portal and revisit the alerts tab I’ll see it highlighted in red.  Clicking it will then enable me to see what is causing it to fail, as well as view the history of when it has happened in the past. Alert Notifications With today’s initial preview you can now easily create alerting rules based on monitoring metrics and get notified on active or impending issues within your application that require attention. During preview, each subscription is limited to 10 alert rules across all of the services that support alert rules. No More Credit Card Requirement for MSDN Subscribers Earlier this month (during TechEd 2013), Windows Azure announced that MSDN users will get Windows Azure Credits every month that they can use for any Windows Azure services they want. You can read details about this in my previous Dev/Test blog post. Today we are making further updates to enable an easier Windows Azure signup for MSDN users. MSDN users will now not be required to provide payment information (e.g. no credit card) during sign-up, so long as they use the service within the included monetary credit for the billing period. For usage beyond the monetary credit, they can enable overages by providing the payment information and remove the spending limit. This enables a super easy, one page sign-up experience for MSDN users.  Simply sign-up for your Windows Azure trial using the same Microsoft ID that you use to manage your MSDN account, then complete the one page sign-up form below and you will be able to spend your free monthly MSDN credits (up to $150 each month) on any Windows Azure resource for dev/test:   This makes it trivially easy for every MDSN customer to start using Windows Azure today.  If you haven’t signed up yet, I definitely recommend checking it out. Summary Today’s release includes a ton of great features that enable you to build even better cloud solutions.  If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using all of the above features today.  Then visit the Windows Azure Developer Center to learn more about how to build apps with it. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

    Read the article

  • Creating static NAT blocks outbound traffic Cisco ASA

    - by natediggs
    Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

    Read the article

  • How repair/uninstall Visual Web Developer 2010 Beta 2?

    - by Sprinter
    I cannot uninstall Visual Web Developer 2010 Beta 2. When I was trying to uninstall the first time, the power went off to my machine and screwed up the Beta 2 installation. I cannot find a Visual Web Developer 2010 Beta 2 download on the Microsoft website any longer to repair the Beta 2 installation. How can I get VWD 2010 Beta 2 off of my system so I can install the new release?

    Read the article

  • Oracle ATG Web Commerce 10 Implementation Developer Boot Camp - Reading (UK) - October 1-12, 2012

    - by Richard Lefebvre
    REGISTER NOW: Oracle ATG Web Commerce 10 Implementation Developer Boot Camp Reading, UK, October 1-12, 2012! OPN invites you to join us for a 10-day implementation bootcamp on Oracle ATG Web Commerce in Reading, UK from October 1-12, 2012.This 10-day boot camp is designed to provide partners with hands-on experience and technical training to successfully build and deploy Oracle ATG Web Commerce 10 Applications. This particular boot camp is focused on helping partners develop the essential skills needed to implement every aspect of an ATG Commerce Application from scratch, (not CRS-based), with a specific goal of enabling experienced Java/J2EE developers with a path towards becoming functional, effective, and contributing members of an ATG implementation team. Built for both new and experienced ATG developers alike, the collaborative nature of this program and its exercises, have proven to be highly effective and extremely valuable in learning the best practices for implementing ATG solutions. Though not required, this bootcamp provides a structured path to earning a Certified Oracle ATG Web Commerce 10 Specialization! What Is Covered: This boot camp is for Application Developers and Software Architects wanting to gain valuable insight into ATG application development best practices, as well as relevant and applicable implementation experience on projects modeled after four of the most common types of applications built on the ATG platform. The following learning objectives are all critical, and are of equal priority in enabling this role to succeed. This learning boot camp will help with: Building a basic functional transaction-ready ATG Web Commerce 10 Application. Utilizing ATG’s platform features such as scenarios, slots, targeters, user profiles and segments, to create a personalized user experience. Building Nucleus components to support and/or extend application functionality. Understanding the intricacies of ATG order checkout and fulfillment. Specifying, designing and implementing new commerce features in ATG 10. Building a functional commerce application modeled after four of the most common types of applications built on the ATG platform, within an agile-based project team environment and under simulated real-world project conditions. Duration: The Oracle ATG Web Commerce 10 Implementation Developer Boot Camp is an instructor-led workshop spanning 10 days. Audience: Application Developers Software Architects Prerequisite Training and Environment Requirements: Programming and Markup Experience with Java J2EE, JavaScript, XML, HTML and CSS Completion of Oracle ATG Web Commerce 10 Implementation Specialist Development Guided Learning Path modules Participants will be required to bring their own laptop that meets the minimum specifications:   64-bit PC and OS (e.g. Windows 7 64-bit) 4GB RAM or more 40GB Hard Disk Space Laptops will require access to the Internet through Remote Desktop via Windows. Agenda Topics: Week 1 – Day 1 through 5 Build a Basic Commerce Application In week one of the boot camp training, we will apply knowledge learned from the ATG Web Commerce 10 Implementation Developer Guided Learning Path modules, towards building a basic transaction-ready commerce application. There will be little to no lectures delivered in this boot camp, as developers will be fully engaged in ATG Application Development activities and best practices. Developers will work independently on the following lab assignments from day's 1 through 5: Lab Assignments  1 Environment Setup 2 Build a dynamic Home Page 3 Site Authentication 4 Build Customer Registration 5 Display Top Level Categories 6 Display Product Sub-Categories 7 Display Product List Page 8 Display Product Detail Page 9 ATG Inventory 10 Build “Add to Cart” Functionality 11 Build Shopping Cart 12 Build Checkout Page  13 Build Checkout Review Page 14 Create an Order and Build Order Confirmation Page 15 Implement Slots and Targeters for Personalization 16 Implement Pricing and Promotions 17 Order Fulfillment Back to top Week 2 – Day 6 through 10 Team-based Case Project In the second week of the boot camp training, participants will be asked to join a project team that will select a case project for the team to implement. Teams will be able to choose from four of the most common application types developed and deployed on the ATG platform. They are as follows: Hard goods with physical fulfillment, Soft goods with electronic fulfillment, a Service or subscription case example, a Course/Event registration case example. Team projects will have approximately 160 hours of use cases/stories for each team to build (40 hours per developer). Each day's Use Cases/Stories will build upon the prior day's work, and therefore must be fully completed at the end of each day. Please note that this boot camp intends to simulate real-world project conditions, and as such will likely require the need for project teams to possibly work beyond normal business hours. To promote further collaboration and group learning, each team will be asked to present their work and share the methodologies and solutions that they've applied to their cases at the end of each day. Location: Oracle Reading CVC TPC510 Room: Wraysbury Reading, UK 9:00 AM – 5:00 PM  Registration Fee (10 Days): US $3,375 Please click on the following link to REGISTER or  visit the Oracle ATG Web Commerce 10 Implementation Developer Boot Camp page for more information. Questions: Patrick Ty Partner Enablement, Oracle Commerce Phone: 310.343.7687 Mobile: 310.633.1013 Email: [email protected]

    Read the article

  • how does a web application cope with thousands of requests?

    - by netrox
    I went to a few websites and noticed that they all use AJAX technology for many tasks such as chat, messages, and so forth. They use a lot of httprequests obviously. My question is if you build a simple website using AJAX and you expected only few people per hour and then you start to have like 1,000 members logged per hour - can a single web application handle more requests per hour if you just upgrade to faster bigger servers or do you have to rewrite the code? Exactly how do you "scale" the web application?

    Read the article

  • Cisco PIX 515 doesn't seem to be passing traffic through according to static route

    - by Liquidkristal
    Ok, so I am having a spot of bother with a Cisco PIX515, I have posted the current running config below, now I am no cisco expert by any means although I can do basic stuff with them, now I am having trouble with traffic sent from the outside to address: 10.75.32.25 it just doesn't appear to be going anywhere. Now this firewall is deep inside a private network, with an upstream firewall that we don't manage. I have spoken to the people that look after that firewall and they say they they have traffic routing to 10.75.32.21 and 10.75.32.25 and thats it (although there is a website that runs from the server 172.16.102.5 which (if my understanding is correct) gets traffic via 10.75.32.23. Any ideas would be greatly appreciated as to me it should all just work, but its not (obviously if the config is all correct then there could be a problem with the web server that we are trying to access on 10.75.32.25, although the users say that they can get to it internally (172.16.102.8) which is even more confusing) PIX Version 6.3(3) interface ethernet0 auto interface ethernet1 auto interface ethernet2 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 nameif ethernet2 academic security50 fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 names name 195.157.180.168 outsideNET name 195.157.180.170 globalNAT name 195.157.180.174 gateway name 195.157.180.173 Mail-Global name 172.30.31.240 Mail-Local name 10.75.32.20 outsideIF name 82.219.210.17 frogman1 name 212.69.230.79 frogman2 name 78.105.118.9 frogman3 name 172.16.0.0 acadNET name 172.16.100.254 acadIF access-list acl_outside permit icmp any any echo-reply access-list acl_outside permit icmp any any unreachable access-list acl_outside permit icmp any any time-exceeded access-list acl_outside permit tcp any host 10.75.32.22 eq smtp access-list acl_outside permit tcp any host 10.75.32.22 eq 8383 access-list acl_outside permit tcp any host 10.75.32.22 eq 8385 access-list acl_outside permit tcp any host 10.75.32.22 eq 8484 access-list acl_outside permit tcp any host 10.75.32.22 eq 8485 access-list acl_outside permit ip any host 10.75.32.30 access-list acl_outside permit tcp any host 10.75.32.25 eq https access-list acl_outside permit tcp any host 10.75.32.25 eq www access-list acl_outside permit tcp any host 10.75.32.23 eq www access-list acl_outside permit tcp any host 10.75.32.23 eq https access-list acl_outside permit tcp host frogman1 host 10.75.32.23 eq ssh access-list acl_outside permit tcp host frogman2 host 10.75.32.23 eq ssh access-list acl_outside permit tcp host frogman3 host 10.75.32.23 eq ssh access-list acl_outside permit tcp any host 10.75.32.23 eq 2001 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8441 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8442 access-list acl_outside permit tcp host frogman1 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp host frogman2 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp host frogman3 host 10.75.32.24 eq 8443 access-list acl_outside permit tcp any host 10.75.32.23 eq smtp access-list acl_outside permit tcp any host 10.75.32.23 eq ssh access-list acl_outside permit tcp any host 10.75.32.24 eq ssh access-list acl_acad permit icmp any any echo-reply access-list acl_acad permit icmp any any unreachable access-list acl_acad permit icmp any any time-exceeded access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq www access-list acl_acad deny tcp any any eq www access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq https access-list acl_acad permit tcp any 10.0.0.0 255.0.0.0 eq 8080 access-list acl_acad permit tcp host 172.16.102.5 host 10.64.1.115 eq smtp pager lines 24 logging console debugging mtu outside 1500 mtu inside 1500 mtu academic 1500 ip address outside outsideIF 255.255.252.0 no ip address inside ip address academic acadIF 255.255.0.0 ip audit info action alarm ip audit attack action alarm pdm history enable arp timeout 14400 global (outside) 1 10.75.32.21 nat (academic) 1 acadNET 255.255.0.0 0 0 static (academic,outside) 10.75.32.22 Mail-Local netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.30 172.30.30.36 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.23 172.16.102.5 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.24 172.16.102.6 netmask 255.255.255.255 0 0 static (academic,outside) 10.75.32.25 172.16.102.8 netmask 255.255.255.255 0 0 access-group acl_outside in interface outside access-group acl_acad in interface academic route outside 0.0.0.0 0.0.0.0 10.75.32.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00 timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00 timeout uauth 0:05:00 absolute aaa-server TACACS+ protocol tacacs+ aaa-server RADIUS protocol radius aaa-server LOCAL protocol local snmp-server host outside 172.31.10.153 snmp-server host outside 172.31.10.154 snmp-server host outside 172.31.10.155 no snmp-server location no snmp-server contact snmp-server community CPQ_HHS no snmp-server enable traps floodguard enable telnet 172.30.31.0 255.255.255.0 academic telnet timeout 5 ssh timeout 5 console timeout 0 terminal width 120 Cryptochecksum:hi2u : end PIX515#

    Read the article

  • Which java web technology to learn to develop Rich Internet Applications ?

    - by Cshah
    Hi, I have developed web applications using JSF (myfaces components). But in these days of responsive UI, JSF doesnt fare well. I m hearing a lot about AJAX, GWT, etc. So i wanted your opinion on which web technology/framework should i learn inorder to develop web applications for enterprise products. Some of the web technologies that i m hearing are: ICE Faces (With AJAX Bridge support) GWT extJS and extGWT JavaFX Apache Wicket Jquery AJAX Open laszlo Which of the above or the combination of the above would help me ? Some of the parameters on which you can rate these web technologies are: Ease of learning Maintainability of web application code Community support IDE support - Eclipse or NetBeans Off the shelf component availability (like textbox,table grids, option menus) License - Does it cost for commercial use ? User Experience - responsive UI. Shouldnt be sluggish A similar question on SO does answer my question partially. Would want more info though. EDIT: Answers collated: Based on the answers : AJAX would be the best thing to start for learning fundamentals, then learn JQUERY. Any component based frame work that can complement ajax,jquery ? Edit 2: If i had to design a web application like StackOverFlow (in java platform) which would be the best choice to learn and adopt? Wicket + Jquery, WiQuery GWT Some XYZ Faces technology(RichFaces/ICEFaces) + AJAX. Comments appreciated from some one who has worked with them and can rate them in the above mentioned parameters.

    Read the article

  • Is there a way to get an ASMX Web Service created in VS 2005 to receive and return JSON?

    - by Ben McCormack
    I'm using .NET 2.0 and Visual Studio 2005 to try to create a web service that can be consumed both as SOAP/XML and JSON. I read Dave Ward's Answer to the question How to return JSON from a 2.0 asmx web service (in addition to reading other articles at Encosia.com), but I can't figure out how I need to set up the code of my asmx file in order to work with JSON using jQuery. Two Questions: How do I enable JSON in my .NET 2.0 ASMX file? What's a simple jQuery call that could consume the service using JSON? Also, I notice that since I'm using .NET 2.0, I i'm not able to implement using System.Web.Script.Services.ScriptService. Here's my C# code for the demo ASMX service: using System; using System.Web; using System.Collections; using System.Web.Services; using System.Web.Services.Protocols; /// <summary> /// Summary description for StockQuote /// </summary> [WebService(Namespace = "http://tempuri.org/")] [WebServiceBinding(ConformsTo = WsiProfiles.BasicProfile1_1)] public class StockQuote : System.Web.Services.WebService { public StockQuote () { //Uncomment the following line if using designed components //InitializeComponent(); } [WebMethod] public decimal GetStockQuote(string ticker) { //perform database lookup here return 8; } [WebMethod] public string HelloWorld() { return "Hello World"; } } Here's a snippet of jQuery I found on the internet and tried to modify: $(document).ready(function(){ $("#btnSubmit").click(function(event){ $.ajax({ type: "POST", contentType: "application/json; charset=utf-8", url: "http://bmccorm-xp/WebServices/HelloWorld.asmx", data: "", dataType: "json" }) event.preventDefault(); }); });

    Read the article

  • How do I implement page authorizaton in ASP.NET using a SQL store instead of web.config?

    - by drachenstern
    For instance, the way we're doing it now is like thus: (in the web.config) <location path="somePath"> <system.web> <authorization> <allow roles="approvedRoles"/> <deny users="*"/> </authorization> </system.web> </location> And what I would like to do instead is to store this information in SQL somewhere so that we can manipulate the information more easily. But we want to keep the same functionality that having the information in web.config provides, just like we can use a SqlRoleProvider instead of hardcoding roles in the app. So in other words, if a user currently tries to goto "somePath" and they're not a member of "approvedRoles" then they get redirected back to default.aspx, and if they are a member of "approvedRoles" then they get the page. I want to do the same thing, but without using web.config as the authorization mechanism. So what I'm NOT asking is how do I go about defining roles, or how do I handle logging in to the database, but specifically how do I store the above information in SQL instead of web.config. Actually, I'll take "anywhere but web.config" for now. Any ideas? Is this possible using a "Provider" class? I'm just looking for pointers on what to inherit and maybe some technet documentation. In this regard my googlefoo is lacking since I don't really know where to point. Am I really only looking for AzMan? Is this location-authorization-via-SQL already defined in the default aspnetdb somewhere and I'm missing it? For that matter, has this question already been asked on SO and I've missed it? What would you google?

    Read the article

  • How do I secure a .NET Web Service for use by an iPhone application?

    - by David A Gibson
    Hello, The title says it all, I have a Web Service written in .NET that provides data for an iPhone application. It will also allow the application make a "reservation." Currently it's all internal to the corporate network but obviously when the iPhone application is published I will need ensure the Web Service is available externally. How would I go about securing the Web Service? There are two aspects I'm looking into: Authentication for accessing the web service Protection for the data being transferred I'm no so bothered about the data being passed back and forth as it will be viewable in the application anyway (which will be free). The key issue for me is preventing users from accessing the Web Service and making reservations themselves. At the moment I am considering encrypting any strings in the XML data passed back and forth so only the client can effectively use the web service sidestepping the need for authentication and providing protection for the data. This is the only model I have seen but I think the overheads on the iPhone and even for the web service make for a poor user experience. Any solutions at all would be most welcome? Thanks

    Read the article

< Previous Page | 125 126 127 128 129 130 131 132 133 134 135 136  | Next Page >