Search Results

Search found 321 results on 13 pages for 'ack'.

Page 13/13 | < Previous Page | 9 10 11 12 13 

  • QNAP (469L) with Debian: can't connect to router

    - by agtoever
    I've been running my QNAP 469L with Debian (Wheezy deb7u3) for a few months. Yesterday I upgraded the memory to 4 GB. The system boots fine, but since the upgrade, I'm not able to connect the server to my router (a TP-Link WR941ND). My configuration: The router runs a DHCP server (192.168.67.100 and up), with a preconfigured ip address for the QNAP (192.168.67.10). The router is on 192.168.67.1. As said, Debian is installed on the QNAP (which can be regarded as a normal computer). Networking hardware on the QNAP: Intel PRO/1000 Network Connection using the e1000e kernel module. This is what I have tried so far: Replace the network cable (tried 3 different cables on different router ports). Check for messages from the kernel: dmesg | grep eth. Besides the normal hardware messages I get a ADDRCONF(NETDEV_UP): eth0: link is not ready for each call to ifup. Manually restart the network sudo server networking restart Check sudo ifconfig (eth0 is up, but no ip addresses). Check the /etc/network/interfaces which has (besides the loopback device) an allow-hotplug eth0 and iface eth0 inet dhcp, which is afaik the default Debian configuration. Since the server has two ethernet ports, I checked if I'm using the right port (checked the hardware address that ifconfig reports for eth0 is the same as the hardware address that is in the preconfigured ip address for the server in the router. Do a manual sudo ifdown eth0 && sudo ifup eth0 with no results (but an extra ADDRCONF(NETDEV_UP): eth0: link is not ready in the kernel log) Do a dhcp request dhclient -v eth0: for about a minute requests are send (according to the terminal) and at the end I get a No DHCPOFFERS received. No working leases in persistent database - sleeping.. Check the router system log if DHCP requests are received. I see them for some devices (my Mac, my iPhone) but not from the QNAP. The log entry looks like: DHCPS:Recv REQUEST from 84:85:06:07:75:6A and then a DHCPS:Send ACK to 192.168.67.101. There are no records from the QNAP's hardware address. So the two error messages that I do get are: ADDRCONF(NETDEV_UP): eth0: link is not ready for every ifup and No DHCPOFFERS received. No working leases in persistent database - sleeping. for every DHCP call.

    Read the article

  • .Net Intermittent System.Web.Services.Protocols.SoapHeaderException

    - by ScottE
    We have a .net 3.5 web app that consumes third party web services. The proxy was created by adding a web reference to their wsdl. This proxy is not compiled. Our error logging is picking up frequent but intermittent exceptions: An exception of type 'System.Web.Services.Protocols.SoapHeaderException' occurred and was caught If I follow the url to the page that generated the exception, I can't recreate it. Edit: Here is most of the exception - where it bubbled up from Message : Internal Error Type : System.Web.Services.Protocols.SoapHeaderException, System.Web.Services, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a Source : System.Web.Services Help link : Actor : Code : http://schemas.xmlsoap.org/soap/envelope/:Client Detail : Lang : Node : Role : SubCode : Data : System.Collections.ListDictionaryInternal TargetSite : System.Object[] ReadResponse(System.Web.Services.Protocols.SoapClientMessage, System.Net.WebResponse, System.IO.Stream, Boolean) Stack Trace : at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) at Vendor.getSearch(getSearchRequest getSearchRequest) in c:\WINDOWS\Microsoft.NET\Framework\v2.0.50727\Temporary ASP.NET Files\root\be43c34e\b09edc7e\App_WebReferences.pww-cf-q.0.cs:line 73 Edit 2: Inner exceptions: I sometimes get the following inner exceptions logged: Message : Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. Type : System.IO.IOException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089 Source : System Help link : Data : System.Collections.ListDictionaryInternal TargetSite : Int32 Read(Byte[], Int32, Int32) Stack Trace : at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) at System.Net.FixedSizeReader.ReadPacket(Byte[] buffer, Int32 offset, Int32 count) at System.Net.Security.SslState.StartReceiveBlob(Byte[] buffer, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.CheckCompletionBeforeNextReceive(ProtocolToken message, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.StartSendBlob(Byte[] incoming, Int32 count, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.ForceAuthentication(Boolean receiveFirst, Byte[] buffer, AsyncProtocolRequest asyncRequest) at System.Net.Security.SslState.ProcessAuthentication(LazyAsyncResult lazyResult) at System.Net.TlsStream.CallProcessAuthentication(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Net.TlsStream.ProcessAuthentication(LazyAsyncResult result) at System.Net.TlsStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.PooledStream.Write(Byte[] buffer, Int32 offset, Int32 size) at System.Net.ConnectStream.WriteHeaders(Boolean async) And/Or: Message : An existing connection was forcibly closed by the remote host Type : System.Net.Sockets.SocketException, System, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089 Source : System Help link : ErrorCode : 10054 SocketErrorCode : ConnectionReset NativeErrorCode : 10054 Data : System.Collections.ListDictionaryInternal TargetSite : Int32 Receive(Byte[], Int32, Int32, System.Net.Sockets.SocketFlags) Stack Trace : at System.Net.Sockets.Socket.Receive(Byte[] buffer, Int32 offset, Int32 size, SocketFlags socketFlags) at System.Net.Sockets.NetworkStream.Read(Byte[] buffer, Int32 offset, Int32 size) Update We're still working on it. Originally there was a route issue, which was resolved. We're still getting the inner exception with socket errors. We had MS support involved today, and they looked at some traces and network captures. The web service host does round-robin DNS, and they may be responding on a different IP address for the syn syn/ack from one ip, and the next from a different ip. This is not good. This is likely quite specific to our situation, but perhaps it applies to others as well. Microsoft Network Monitor and an application trace got us the information we needed.

    Read the article

  • Paypal NVP API - Keep getting error 81002

    - by Andree
    Hi there, I am new to PayPal API, and I'm having trouble calling SetExpressCheckout using CURL in PHP. I have set everything correctly, as far as I'm concerned, but I kept getting an 81002 error "Method Specified is not Supported". The code snippet is below. I got the CA Root certificates file from here. <?php $paypal_data = array( 'USER' => urlencode('andree_1272823561_biz_api1.gmail.com'), 'PWD' => urlencode('1272823576'), 'SIGNATURE' => urlencode('Am1t0wiu2tv7VwZ5ebdeY9zv1GF6Ad0PFz-qTGFFf7vbWU6ee4bxy8KL'), 'VERSION' => urlencode('52.0'), 'PAYMENTACTION' => urlencode('Sale'), 'METHOD' => urlencode('SetExpressCheckout'), 'AMT' => urlencode('52.00'), 'RETURNURL' => urlencode('get_express_checkout_details.php'), 'CANCELURL' => urlencode('index.php') ); $url = 'https://api-3t.sandbox.paypal.com/nvp?' . http_build_query($paypal_data); $curl = curl_init(); curl_setopt($curl, CURLOPT_URL, $url); curl_setopt($curl, CURLOPT_RETURNTRANSFER, 1); curl_setopt($curl, CURLOPT_CAINFO, dirname(__FILE__) . '/cacert.pem'); $result = curl_exec($curl); curl_close($curl); parse_str($result, $result); ?> <pre>Data sent: <?php print_r($paypal_data); ?></pre> <pre>Result: <?php print_r($result); ?></pre> When I run the code, the output is the following: Data sent: Array ( [USER] => andree_1272823561_biz_api1.gmail.com [PWD] => 1272823576 [SIGNATURE] => Am1t0wiu2tv7VwZ5ebdeY9zv1GF6Ad0PFz-qTGFFf7vbWU6ee4bxy8KL [VERSION] => 52.0 [PAYMENTACTION] => Sale [METHOD] => SetExpressCheckout [AMT] => 52.00 [RETURNURL] => get_express_checkout_details.php [CANCELURL] => index.php ) Result: Array ( [ACK] => Failure [L_ERRORCODE0] => 81002 [L_SHORTMESSAGE0] => Unspecified Method [L_LONGMESSAGE0] => Method Specified is not Supported [L_SEVERITYCODE0] => Error ) Anyone knows what could be the problem? Regards, Andree.

    Read the article

  • Java Webservice java.lang.ClassCastException: org.apache.cxf.jaxws.ServiceImpl

    - by JohnC
    I am using Maven, CXF 2.2.7, JBoss 4.2.3 and JRE 1.5 I have a Webservice that I can see on the server by using the URL myURL/myService?wsdl I am trying to develop a web app to ping that webservice by calling this in my bean: MyWebService webservice = new MyWebService(); However, it dies and throws the following error, which is very vague: java.lang.ClassCastException: org.apache.cxf.jaxws.ServiceImpl 09:25:59,450 ERROR [STDERR] at javax.xml.ws.Service.<init>(Service.java:81) 09:25:59,450 ERROR [STDERR] at org.otherservice.webservice.MyWebServiceService.<init>(MyWebService.java:44) 09:25:59,450 ERROR [STDERR] at net.myservice.beans.MyBean.getMyServiceSoap(MyBean.java:109) 09:25:59,450 ERROR [STDERR] at net.myservice.beans.MyBean.ack(MyBean.java:240) 09:25:59,450 ERROR [STDERR] at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) 09:25:59,450 ERROR [STDERR] at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) 09:25:59,450 ERROR [STDERR] at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) 09:25:59,450 ERROR [STDERR] at java.lang.reflect.Method.invoke(Method.java:585) 09:25:59,450 ERROR [STDERR] at org.apache.el.parser.AstValue.invoke(AstValue.java:131) 09:25:59,450 ERROR [STDERR] at org.apache.el.MethodExpressionImpl.invoke(MethodExpressionImpl.java:276) 09:25:59,450 ERROR [STDERR] at org.apache.jasper.el.JspMethodExpression.invoke(JspMethodExpression.java:68) 09:25:59,450 ERROR [STDERR] at javax.faces.component.MethodBindingMethodExpressionAdapter.invoke(MethodBindingMethodExpressionAdapter.java:77) 09:25:59,450 ERROR [STDERR] at com.sun.faces.application.ActionListenerImpl.processAction(ActionListenerImpl.java:95) 09:25:59,450 ERROR [STDERR] at javax.faces.component.UICommand.broadcast(UICommand.java:383) 09:25:59,450 ERROR [STDERR] at javax.faces.component.UIViewRoot.broadcastEvents(UIViewRoot.java:450) 09:25:59,450 ERROR [STDERR] at javax.faces.component.UIViewRoot.processApplication(UIViewRoot.java:759) 09:25:59,450 ERROR [STDERR] at com.sun.faces.lifecycle.InvokeApplicationPhase.execute(InvokeApplicationPhase.java:97) 09:25:59,450 ERROR [STDERR] at com.sun.faces.lifecycle.LifecycleImpl.phase(LifecycleImpl.java:266) 09:25:59,450 ERROR [STDERR] at com.sun.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:132) 09:25:59,450 ERROR [STDERR] at javax.faces.webapp.FacesServlet.service(FacesServlet.java:244) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at org.apache.myfaces.webapp.filter.ExtensionsFilter.doFilter(ExtensionsFilter.java:301) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at net.faces.filters.AuthorizationFilter.doFilter(AuthorizationFilter.java:84) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.filters.ReplyHeaderFilter.doFilter(ReplyHeaderFilter.java:96) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:230) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:175) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.security.SecurityAssociationValve.invoke(SecurityAssociationValve.java:182) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.security.JaccContextValve.invoke(JaccContextValve.java:84) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.service.jca.CachedConnectionValve.invoke(CachedConnectionValve.java:157) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:262) 09:25:59,450 ERROR [STDERR] at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:844) 09:25:59,450 ERROR [STDERR] at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:583) 09:25:59,450 ERROR [STDERR] at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:446) 09:25:59,450 ERROR [STDERR] at java.lang.Thread.run(Thread.java:595) I am hoping someone has seen this exception before and can help me.

    Read the article

  • CakePHP Test Fixtures Drop My Tables Permanently After Running A Test Case

    - by Frank
    I'm not sure what I've done wrong in my CakePHP unit test configuration. Every time I run a test case, the model tables associated with my fixtures are missing form my test database. After running an individual test case I have to re-import my database tables using phpMyAdmin. Here are the relevant files: This is the class I'm trying to test comment.php. This table is dropped after the test. App::import('Sanitize'); class Comment extends AppModel{ public $name = 'Comment'; public $actsAs = array('Tree'); public $belongsTo = array('User' => array('fields'=>array('id', 'username'))); public $validate = array( 'text' = array( 'rule' =array('between', 1, 4000), 'required' ='true', 'allowEmpty'='false', 'message' = "You can't leave your comment text empty!") ); database.php class DATABASE_CONFIG { var $default = array( 'driver' = 'mysql', 'persistent' = false, 'host' = 'project.db', 'login' = 'projectman', 'password' = 'projectpassword', 'database' = 'projectdb', 'prefix' = '' ); var $test = array( 'driver' = 'mysql', 'persistent' = false, 'host' = 'project.db', 'login' = 'projectman', 'password' = 'projectpassword', 'database' = 'testprojectdb', 'prefix' = '' ); } My comment.test.php file. This is the table that keeps getting dropped. <?php App::import('Model', 'Comment'); class CommentTestCase extends CakeTestCase { public $fixtures = array('app.comment', 'app.user'); function start(){ $this-Comment =& ClassRegistry::init('Comment'); $this-Comment-useDbConfig = 'test_suite'; } This is my comment_fixture.php class: <?php class CommentFixture extends CakeTestFixture { var $name = "Comment"; var $import = 'Comment'; } And just in case, here is a typical test method in the CommentTestCase class function testMsgNotificationUserComment(){ $user_id = '1'; $submission_id = '1'; $parent_id = $this-Comment-commentOnModel('Submission', $submission_id, '0', $user_id, "Says: A"); $other_user_id = '2'; $msg_id = $this-Comment-commentOnModel('Submission', $submission_id, $parent_id, $other_user_id, "Says: B"); $expected = array(array('Comment'=array('id'=$msg_id, 'text'="Says: B", 'submission_id'=$submission_id, 'topic_id'='0', 'ack'='0'))); $result = $this-Comment-getMessages($user_id); $this-assertEqual($result, $expected); } I've been dealing with this for a day now and I'm starting to be put off by CakePHP's unit testing. In addition to this issue -- Servral times now I've had data inserted into by 'default' database configuration after running tests! What's going on with my configuration?!

    Read the article

  • Diagnosing packet loss / high latency in Ubuntu

    - by Sam Gammon
    We have a Linux box (Ubuntu 12.04) running Nginx (1.5.2), which acts as a reverse proxy/load balancer to some Tornado and Apache hosts. The upstream servers are physically and logically close (same DC, sometimes same-rack) and show sub-millisecond latency between them: PING appserver (10.xx.xx.112) 56(84) bytes of data. 64 bytes from appserver (10.xx.xx.112): icmp_req=1 ttl=64 time=0.180 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=2 ttl=64 time=0.165 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=3 ttl=64 time=0.153 ms We receive a sustained load of about 500 requests per second, and are currently seeing regular packet loss / latency spikes from the Internet, even from basic pings: sam@AM-KEEN ~> ping -c 1000 loadbalancer PING 50.xx.xx.16 (50.xx.xx.16): 56 data bytes 64 bytes from loadbalancer: icmp_seq=0 ttl=56 time=11.624 ms 64 bytes from loadbalancer: icmp_seq=1 ttl=56 time=10.494 ms ... many packets later ... Request timeout for icmp_seq 2 64 bytes from loadbalancer: icmp_seq=2 ttl=56 time=1536.516 ms 64 bytes from loadbalancer: icmp_seq=3 ttl=56 time=536.907 ms 64 bytes from loadbalancer: icmp_seq=4 ttl=56 time=9.389 ms ... many packets later ... Request timeout for icmp_seq 919 64 bytes from loadbalancer: icmp_seq=918 ttl=56 time=2932.571 ms 64 bytes from loadbalancer: icmp_seq=919 ttl=56 time=1932.174 ms 64 bytes from loadbalancer: icmp_seq=920 ttl=56 time=932.018 ms 64 bytes from loadbalancer: icmp_seq=921 ttl=56 time=6.157 ms --- 50.xx.xx.16 ping statistics --- 1000 packets transmitted, 997 packets received, 0.3% packet loss round-trip min/avg/max/stddev = 5.119/52.712/2932.571/224.629 ms The pattern is always the same: things operate fine for a while (<20ms), then a ping drops completely, then three or four high-latency pings (1000ms), then it settles down again. Traffic comes in through a bonded public interface (we will call it bond0) configured as such: bond0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5d inet addr:50.xx.xx.16 Bcast:50.xx.xx.31 Mask:255.255.255.224 inet6 addr: <ipv6 address> Scope:Global inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:527181270 errors:1 dropped:4 overruns:0 frame:1 TX packets:413335045 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240016223540 (240.0 GB) TX bytes:104301759647 (104.3 GB) Requests are then submitted via HTTP to upstream servers on the private network (we can call it bond1), which is configured like so: bond1 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5c inet addr:10.xx.xx.70 Bcast:10.xx.xx.127 Mask:255.255.255.192 inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:430293342 errors:1 dropped:2 overruns:0 frame:1 TX packets:466983986 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:77714410892 (77.7 GB) TX bytes:227349392334 (227.3 GB) Output of uname -a: Linux <hostname> 3.5.0-42-generic #65~precise1-Ubuntu SMP Wed Oct 2 20:57:18 UTC 2013 x86_64 GNU/Linux We have customized sysctl.conf in an attempt to fix the problem, with no success. Output of /etc/sysctl.conf (with irrelevant configs omitted): # net: core net.core.netdev_max_backlog = 10000 # net: ipv4 stack net.ipv4.tcp_ecn = 2 net.ipv4.tcp_sack = 1 net.ipv4.tcp_fack = 1 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_timestamps = 1 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_max_syn_backlog = 10000 net.ipv4.tcp_congestion_control = cubic net.ipv4.ip_local_port_range = 8000 65535 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_thin_dupack = 1 net.ipv4.tcp_thin_linear_timeouts = 1 net.netfilter.nf_conntrack_max = 99999999 net.netfilter.nf_conntrack_tcp_timeout_established = 300 Output of dmesg -d, with non-ICMP UFW messages suppressed: [508315.349295 < 19.852453>] [UFW BLOCK] IN=bond1 OUT= MAC=<mac addresses> SRC=118.xx.xx.143 DST=50.xx.xx.16 LEN=68 TOS=0x00 PREC=0x00 TTL=51 ID=43221 PROTO=ICMP TYPE=3 CODE=1 [SRC=50.xx.xx.16 DST=118.xx.xx.143 LEN=40 TOS=0x00 PREC=0x00 TTL=249 ID=10220 DF PROTO=TCP SPT=80 DPT=53817 WINDOW=8190 RES=0x00 ACK FIN URGP=0 ] [517787.732242 < 0.443127>] Peer 190.xx.xx.131:59705/80 unexpectedly shrunk window 1155488866:1155489425 (repaired) How can I go about diagnosing the cause of this problem, on a Debian-family Linux box?

    Read the article

  • Iptables blocking mysql port 3306

    - by valmar
    I got a Tomcat server running a web application that must access a mysql server via Hibernate on the same machine. So, I added a rule for port 3306 to my iptables script but tomcat cannot connect to the mysql server for some reason. I need to reset all iptables rules - Then tomcat can connect to the mysql server again. All the other iptables rules work perfectly though. What's wrong? Here is my script: iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p tcp --dport 24 -j ACCEPT iptables -A INPUT -p tcp --dport 80 -j ACCEPT iptables -A OUTPUT -p tcp --dport 80 -j ACCEPT iptables -A INPUT -p tcp -s localhost --dport 8009 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp -d localhost --dport 8009 -j ACCEPT iptables -A INPUT -p tcp -s localhost --dport 3306 -j ACCEPT iptables -A OUTPUT -p tcp -d localhost --dport 3306 -j ACCEPT iptables -A INPUT -p tcp --dport 443 -j ACCEPT iptables -A OUTPUT -p tcp --dport 443 -j ACCEPT iptables -A INPUT -p tcp --dport 25 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 25 -j ACCEPT iptables -A INPUT -p tcp --dport 587 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 587 -j ACCEPT iptables -A INPUT -p tcp --dport 465 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 465 -j ACCEPT iptables -A INPUT -p tcp --dport 110 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 110 -j ACCEPT iptables -A INPUT -p tcp --dport 995 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 995 -j ACCEPT iptables -A INPUT -p tcp --dport 143 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 143 -j ACCEPT iptables -A INPUT -p tcp --dport 993 -m state --state ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --dport 993 -j ACCEPT iptables -A INPUT -j DROP My /etc/hosts file: # nameserver config # IPv4 127.0.0.1 localhost 46.4.7.93 mydomain.com 46.4.7.93 Ubuntu-1004-lucid-64-minimal 46.4.7.93 horst # IPv6 ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts Having a look into the iptables logs, gives me this: Jun 22 16:52:43 Ubuntu-1004-lucid-64-minimal kernel: [ 435.111780] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=52432 DF PROTO=TCP SPT=56108 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:52:46 Ubuntu-1004-lucid-64-minimal kernel: [ 438.110555] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=52433 DF PROTO=TCP SPT=56108 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:52:46 Ubuntu-1004-lucid-64-minimal kernel: [ 438.231954] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=48020 DF PROTO=TCP SPT=56109 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:52:49 Ubuntu-1004-lucid-64-minimal kernel: [ 441.229778] denied-input IN=lo OUT= MAC=00:00:00:00:00:00:00:00:00:00:00:00:08:00 SRC=127.0.0.1 DST=127.0.0.1 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=48021 DF PROTO=TCP SPT=56109 DPT=8009 WINDOW=32792 RES=0x00 SYN URGP=0 Jun 22 16:53:57 Ubuntu-1004-lucid-64-minimal kernel: [ 508.731839] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=78.92.97.67 DST=46.4.7.93 LEN=64 TOS=0x00 PREC=0x00 TTL=122 ID=23053 DF PROTO=TCP SPT=1672 DPT=445 WINDOW=65535 RES=0x00 SYN URGP=0 Jun 22 16:53:59 Ubuntu-1004-lucid-64-minimal kernel: [ 511.625038] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=78.92.97.67 DST=46.4.7.93 LEN=64 TOS=0x00 PREC=0x00 TTL=122 ID=23547 DF PROTO=TCP SPT=1672 DPT=445 WINDOW=65535 RES=0x00 SYN URGP=0 Jun 22 16:54:22 Ubuntu-1004-lucid-64-minimal kernel: [ 533.981995] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=27.254.39.16 DST=46.4.7.93 LEN=48 TOS=0x00 PREC=0x00 TTL=117 ID=6549 PROTO=TCP SPT=6005 DPT=33796 WINDOW=64240 RES=0x00 ACK SYN URGP=0 Jun 22 16:54:44 Ubuntu-1004-lucid-64-minimal kernel: [ 556.297038] denied-input IN=eth0 OUT= MAC=6c:62:6d:85:bf:0e:00:26:88:75:dc:01:08:00 SRC=94.78.93.41 DST=46.4.7.93 LEN=40 TOS=0x00 PREC=0x00 TTL=52 ID=7712 PROTO=TCP SPT=57598 DPT=445 WINDOW=512 RES=0x00 SYN URGP=0

    Read the article

  • iCloud stuff stops working while connected to OpenVPN

    - by Taco Bob
    I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again! (I tried serverfault, it was closed as off-topic. I'm trying here and the Unix site as well. Here because it's a more general audience that might know more about OpenVPN based on the number of questions I see asked about it) EDIT: -I have also tried upgrading to Version: 2.3-beta1-debian0 - issue persists. -Removed all iptables rules except for the ones that flush -left this rule:iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source (server ip) -added iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT still, nothing works. I can see traffic in tcpdump on the server if i watch the tunnel: 20:03:48.702835 IP nk11p01st-courier105-bz.push.apple.com.5223 10.9.8.6.60772: Flags [F.], seq 2635, ack 1218, win 76, options [nop,nop,TS val 914984811 ecr 745921298], length 0 20:03:48.911244 IP 10.9.8.6.60772 nk11p01st-courier105-bz.push.apple.com.5223: Flags [R], seq 3621143451, win 0, length 0 But still, no push messages/notifications are ever delivered. :/ EDIT: * Further testing indicates that it might actually be the client after all.

    Read the article

  • obtaining nimbuzz server certificate for nmdecrypt expert in NetMon

    - by lurscher
    I'm using Network Monitor 3.4 with the nmdecrypt expert. I'm opening a nimbuzz conversation node in the conversation window and i click Expert- nmDecrpt - run Expert that shows up a window where i have to add the server certificate. I am not sure how to retrieve the server certificate for nimbuzz XMPP chat service. Any idea how to do this? this question is a follow up question of this one. Edit for some background so it might be that this is encrypted with the server pubkey and i cannot retrieve the message, unless i debug the native binary and try to intercept the encryption code. I have a test client (using agsXMPP) that is able to connect with nimbuzz with no problems. the only thing that is not working is adding invisible mode. It seems this is some packet sent from the official client during login which i want to obtain. any suggestions to try to grab this info would be greatly appreciated. Maybe i should get myself (and learn) IDA pro? This is what i get inspecting the TLS frames on Network Monitor: Frame: Number = 81, Captured Frame Length = 769, MediaType = ETHERNET + Ethernet: Etype = Internet IP (IPv4),DestinationAddress:[...],SourceAddress:[....] + Ipv4: Src = ..., Dest = 192.168.2.101, Next Protocol = TCP, Packet ID = 9939, Total IP Length = 755 - Tcp: Flags=...AP..., SrcPort=5222, DstPort=3578, PayloadLen=715, Seq=4101074854 - 4101075569, Ack=1127356300, Win=4050 (scale factor 0x0) = 4050 SrcPort: 5222 DstPort: 3578 SequenceNumber: 4101074854 (0xF4716FA6) AcknowledgementNumber: 1127356300 (0x4332178C) + DataOffset: 80 (0x50) + Flags: ...AP... Window: 4050 (scale factor 0x0) = 4050 Checksum: 0x8841, Good UrgentPointer: 0 (0x0) TCPPayload: SourcePort = 5222, DestinationPort = 3578 TLSSSLData: Transport Layer Security (TLS) Payload Data - TLS: TLS Rec Layer-1 HandShake: Server Hello.; TLS Rec Layer-2 HandShake: Certificate.; TLS Rec Layer-3 HandShake: Server Hello Done. - TlsRecordLayer: TLS Rec Layer-1 HandShake: ContentType: HandShake: - Version: TLS 1.0 Major: 3 (0x3) Minor: 1 (0x1) Length: 42 (0x2A) - SSLHandshake: SSL HandShake ServerHello(0x02) HandShakeType: ServerHello(0x02) Length: 38 (0x26) - ServerHello: 0x1 + Version: TLS 1.0 + RandomBytes: SessionIDLength: 0 (0x0) TLSCipherSuite: TLS_RSA_WITH_AES_256_CBC_SHA { 0x00, 0x35 } CompressionMethod: 0 (0x0) - TlsRecordLayer: TLS Rec Layer-2 HandShake: ContentType: HandShake: - Version: TLS 1.0 Major: 3 (0x3) Minor: 1 (0x1) Length: 654 (0x28E) - SSLHandshake: SSL HandShake Certificate(0x0B) HandShakeType: Certificate(0x0B) Length: 650 (0x28A) - Cert: 0x1 CertLength: 647 (0x287) - Certificates: CertificateLength: 644 (0x284) - X509Cert: Issuer: nimbuzz.com,Nimbuzz,NL, Subject: nimbuzz.com,Nimbuzz,NL + SequenceHeader: - TbsCertificate: Issuer: nimbuzz.com,Nimbuzz,NL, Subject: nimbuzz.com,Nimbuzz,NL + SequenceHeader: + Tag0: + Version: (2) + SerialNumber: -1018418383 + Signature: Sha1WithRSAEncryption (1.2.840.113549.1.1.5) - Issuer: nimbuzz.com,Nimbuzz,NL - RdnSequence: nimbuzz.com,Nimbuzz,NL + SequenceOfHeader: 0x1 + Name: NL + Name: Nimbuzz + Name: nimbuzz.com + Validity: From: 02/22/10 20:22:32 UTC To: 02/20/20 20:22:32 UTC + Subject: nimbuzz.com,Nimbuzz,NL - SubjectPublicKeyInfo: RsaEncryption (1.2.840.113549.1.1.1) + SequenceHeader: + Algorithm: RsaEncryption (1.2.840.113549.1.1.1) - SubjectPublicKey: - AsnBitStringHeader: - AsnId: BitString type (Universal 3) - LowTag: Class: (00......) Universal (0) Type: (..0.....) Primitive TagValue: (...00011) 3 - AsnLen: Length = 141, LengthOfLength = 1 LengthType: LengthOfLength = 1 Length: 141 bytes BitString: + Tag3: + Extensions: - SignatureAlgorithm: Sha1WithRSAEncryption (1.2.840.113549.1.1.5) - SequenceHeader: - AsnId: Sequence and SequenceOf types (Universal 16) + LowTag: - AsnLen: Length = 13, LengthOfLength = 0 Length: 13 bytes, LengthOfLength = 0 + Algorithm: Sha1WithRSAEncryption (1.2.840.113549.1.1.5) - Parameters: Null Value - Sha1WithRSAEncryption: Null Value + AsnNullHeader: - Signature: - AsnBitStringHeader: - AsnId: BitString type (Universal 3) - LowTag: Class: (00......) Universal (0) Type: (..0.....) Primitive TagValue: (...00011) 3 - AsnLen: Length = 129, LengthOfLength = 1 LengthType: LengthOfLength = 1 Length: 129 bytes BitString: + TlsRecordLayer: TLS Rec Layer-3 HandShake:

    Read the article

  • WinInet Apps failing when Internet Explorer is set to Offline Mode

    - by Rick Strahl
    Ran into a nasty issue last week when all of a sudden many of my old applications that are using WinInet for HTTP access started failing. Specifically, the WinInet HttpSendRequest() call started failing with an error of 2, which when retrieving the error boils down to: WinInet Error 2: The system cannot find the file specified Now this error can pop up in many legitimate scenarios with WinInet such as when no Internet connection is available or the HTTP configuration (usually configured in Internet Explorer’s options) is misconfigured. The error typically means that the server in question cannot be found or more specifically an Internet connection can’t be established. In this case the problem started suddenly and was causing some of my own applications (old Visual FoxPro apps using my own wwHttp library) and all Adobe Air applications (which apparently uses WinInet for its basic HTTP stack) along with a few more oddball applications to fail instantly when trying to connect via HTTP. Most other applications – all of my installed browsers, email clients, various social network updaters all worked just fine. It seems it was only WinInet apps that were failing. Yet oddly Internet Explorer appeared to be working. So the problem seemed to be isolated to those ‘classic’ applications using WinInet. WinInet’s base configuration uses the Internet Explorer options dialog. To check this out I typically go to the Internet Explorer options and find the Connection tab, and check out the LAN Setup. Make sure there are no rogue proxy settings or configuration scripts that are invalid. Trying with Auto-configuration on and off also can often fix ‘real’ configuration errors. This time however this wasn’t a problem – nothing in the LAN configuration was set (all default). I also played with the Automatic detection of settings which also had no effect. I also tried to use Fiddler to see if that would tell me something. Fiddler has a few additional WinInet configuration options in its configuration. Running Fiddler and hitting an HTTP request using WinInet would never actually hit Fiddler – the failure would occur before WinInet ever fired up the HTTP connection to go through the Fiddler HTTP proxy. And the Culprit is: Internet Explorer’s Work Offline Option The culprit in this situation was Internet Explorer which at some point, unknown to me switched into Offline Mode and was then shut down: When this Offline mode is checked when IE is running *or* if IE gets shut down with this flag set, all applications using WinInet by default assume that it’s running in offline mode. Depending on your caching HTTP headers and whether the page was cached previously you may or may not get a response or an error. For an independent non-browser application this will be highly unpredictable and likely result in failures getting online – especially if the application forces requests to always reload by disabling HTTP caching (as I do on most of my dynamic HTTP clients). What makes this especially tricky is that even when IE is in offline mode in the browser, you can still browse around the Web *if* you have a connection. IE will try to load anything it has cached from the local cache, but as soon as you hit a URL that isn’t cached it will automatically try to access that URL and uncheck the Work Offline option. Conversely if you get knocked off the Internet and browse in IE 9, IE will automatically go into offline mode. I never explicitly set offline mode – it just automatically sets itself on and off depending on the connection. Problem is if you’re not using IE all the time (as I do – rarely and just for testing so usually a few commonly used URLs) and you left it in offline mode when you exit, offline mode stays set which results in the above head scratcher. Ack. This isn’t new behavior in IE 9 BTW – this behavior has always been there, but I think what’s different is that IE now automatically switches between online and offline modes without notifying you at all, so it’s hard to tell when you are offline. Fixing the Issue in your Code If you have an application that is using WinInet, there’s a WinInet option called INTERNET_OPTION_IGNORE_OFFLINE. I just checked this out in my own applications and Internet Explorer 9 and it works, but apparently it’s been broken for some older releases (I can’t confirm how far back though) – lots of posts seem to suggest the flag doesn’t work. However, in IE 9 at least it does seem to work if you call InternetSetOption before you call HttpOpenRequest with the Http Session handle. In FoxPro code I use: DECLARE INTEGER InternetSetOption ;    IN WININET.DLL ;    INTEGER HINTERNET,;    INTEGER dwFlags,;    INTEGER @dwValue,;    INTEGER cbSize lnOptionValue = 1   && BOOL TRUE pass by reference   *** Set needed SSL flags lnResult=InternetSetOption(this.hHttpSession,;    INTERNET_OPTION_IGNORE_OFFLINE ,;  && 77    @lnOptionValue ,4)   DECLARE INTEGER HttpOpenRequest ;    IN WININET.DLL ;    INTEGER hHTTPHandle,;    STRING lpzReqMethod,;    STRING lpzPage,;    STRING lpzVersion,;    STRING lpzReferer,;    STRING lpzAcceptTypes,;    INTEGER dwFlags,;    INTEGER dwContextw     hHTTPResult=HttpOpenRequest(THIS.hHttpsession,;    lcVerb,;    tcPage,;    NULL,NULL,NULL,;    INTERNET_FLAG_RELOAD + ;    IIF(THIS.lsecurelink,INTERNET_FLAG_SECURE,0) + ;    this.nHTTPServiceFlags,0) …  And this fixes the issue at least for IE 9… In my FoxPro wwHttp class I now call this by default to never get bitten by this again… This solves the problem permanently for my HTTP client. I never want to see offline operation in an HTTP client API – it’s just too unpredictable in handling errors and the last thing you want is getting unpredictably stale data. Problem solved but this behavior is – well ugly. But then that’s to be expected from an API that’s based on Internet Explorer, eh?© Rick Strahl, West Wind Technologies, 2005-2011Posted in HTTP  Windows  

    Read the article

  • Quick guide to Oracle IRM 11g: Creating your first sealed document

    - by Simon Thorpe
    Quick guide to Oracle IRM 11g indexThe previous articles in this guide have detailed how to install, configure and secure your Oracle IRM 11g service. This article walks you through the process of now creating your first context and securing a document against it. I should mention that it would be worth reviewing the following to ensure your installation is ready for that all important first document. Ensure you have correctly configured the keystore for the IRM wrapper keys. If this is not correctly configured, creating the context below will fail. Make sure the IRM server URL correctly resolves and uses the right protocol (HTTP or HTTPS) ContentsCreate the first contextInstall the Oracle IRM Desktop Seal your first document Create the first contextIn Oracle 11g there is a built in classification and rights system called the "standard rights model" which is based on 10 years of customer use cases and innovation. It is a system which enables IRM to scale massively whilst retaining the ability to balance security and usability and also separate duties by allowing contacts in the business to own classifications. The final article in this guide goes into detail on this inbuilt classification model, but for the purposes of this current article all we need to do is create at least one context to test our system out.With a new IRM server there are a set of predefined context templates and roles which again are setup in a way which reflects the most common use we've learned from our customers. We will use these out of the box configurations as they are to create the first context against which we will seal some content.First login to your Oracle IRM Management Website located at https://irm.company.com/irm_rights/. Currently the system is only configured to use the built in LDAP for users, so use the only account we have at the moment, which by default is weblogic. Once logged in switch to the Contexts tab. Click on the New Context icon () in the menu bar on the left. In the resulting dialog select the Standard context template and enter in a name for the context. Then just hit finish, the weblogic account will automatically be made the manager. You'll now see your brand new context ready for users to be assigned. Now click on the Assign Role icon () in the menu bar and in the resulting dialog search for your only user account, weblogic, and add to the list on the right. Now select a role for this user. Because we need to create a document with this user we must select contributor, as this is the only role which allows for the ability to seal. Finally hit next and then finish. We now have a context with a user that has the rights to create a document. The next step is to configure the IRM Desktop to get these rights from the server. Install the Oracle IRM Desktop Before we can seal a document we need the client software installed. Oracle IRM has a very small, lightweight client called the Oracle IRM Desktop which can be freely downloaded in 27 languages from here. Double click on the installer and click on next... Next again... And finally on install... Very easy. You may get a warning about closing Outlook, Word or another application and most of the time no reboots are required. Once it is installed you will see the IRM Desktop icon running in your tool tray, bottom right of the desktop. Seal your first document Finally the prize is within reach, creating your first sealed document. The server is running, we've got a context ready, a user assigned a role in the context but there is the simple and obvious hoop left to jump through. To seal a document we need to have the users rights cached to the local machine. For this to take place, the IRM Desktop needs to know where the Oracle IRM server is on the network so we can synchronize these rights and then be able to seal a document. The usual way for the IRM Desktop to know about the IRM server is it learns automatically when you open an existing piece of content that someone has sent you... ack. Bit of a chicken or the egg dilemma. The solution is to manually tell the IRM Desktop the location of the IRM Server and then force a synchronization of rights. Right click on the Oracle IRM Desktop icon in the system tray and select Options.... Then switch to the Servers tab in the resulting dialog. There are no servers in the list because you've never opened any content. This list is usually populated automatically but we are going to add a server manually, so click on New.... Into the dialog enter in the full URL to the IRM server. Note that this time you use the path /irm_desktop/ and not /irm_rights/. You can see an example from the image below. Click on the validate button and you'll be asked to authenticate. Enter in your weblogic username and password and also check the Remember my password check box. Click OK and the IRM Desktop will confirm a successful connection to the server. OK all the dialogs and we are ready to Synchronize this users rights to the desktop. Right click once more on the Oracle IRM Desktop icon in the system tray. Now the Synchronize menu option is available. Select this and the IRM Desktop will now talk to the IRM server, authenticate using your weblogic account and get your rights to the context we created. Because this is the first time this users has communicated with the IRM server the IRM Desktop presents a privacy policy dialog. This is a chance for the business to ask users to agree to any policy about the use of IRM before opening secured documents. In our guide we've not bothered to setup this URL so just click on the check box and hit Accept. The IRM Desktop will then talk to the server, get your rights and display a success dialog. Lets protect a documentNow we are ready to seal a piece of content. In my guide i'm going to protect a Microsoft Word document. This mean's I have to have copy of Office installed, in this guide i'm using Microsoft Office 2007. You could also seal a PDF document, you'll need to download and install Adobe Acrobat Reader. A very simple test could be to seal a GIF/JPG/PNG or piece of HTML because this is rendered using Internet Explorer. But as I say, i'm going to protect a Word document. The following example demonstrates choosing a file in Windows Explorer, there are many ways to seal a file and you can watch a few in this video.Open a copy of Windows Explorer and locate the file you wish to seal. Right click on the document and select Seal To -> Context You are now presented with the Select Context dialog. You'll now have a sealed copy of the document sat in the same location. Double click on this document and it will open, again using the credentials you've already provided. That is it, now you just need to add more users, more documents, more classifications and start exploring the different roles and experiment with different offline periods etc. You may wish to setup the server against an existing LDAP or Active Directory environment instead of using the built in WebLogic LDAP store. You can read how to use your corporate directory here. But before we finish this guide, there is one more article and arguably the most important article of all. Next I discuss the all important decision making surrounding the actually implementation of Oracle IRM inside your business. Who has rights to what? How do you map contexts to your existing business practices? It is the next article which actually ensures you deploy a successful IRM solution by looking at the business and understanding how they use your sensitive information and then configuring Oracle IRM to reflect their use.

    Read the article

  • Why won't fetchmail work all of a sudden?

    - by SirCharlo
    I ran a chmod 777 * on my home folder. (I know, I know. I'll never do it again.) Ever since then, fetchmail seems to be broken. I use it to fetch mail from an Exchange 2003 mailbox through DAVMail and OWA. The problem is that fetchmail complains about an "expunge mismatch" whenever I get a new message. It deletes the message from the Exchange mailbox, yet it never forwards it. There seems to be a problem somwhere along the mail processing, but I haven't been able to pinpoint where. Any help would be appreciated. Here are the relevant config files. ~/fetchmailrc: set no bouncemail defaults: antispam -1 batchlimit 100 poll localhost with protocol imap and port 1143 user domain\\user password Password is root no rewrite mda "/usr/bin/procmail -f %F -d %T"; ~/procmailrc: :0 * ^Subject.*ack | expand | sed -e 's/[ ]*$//g' | sed -e 's/^/ /' > /usr/local/nagios/libexec/mail_acknowledgement ~/.forward: | "/usr/bin/procmail" And here is the output when I run fetchmail -f /root/.fetchmailrc -vv: fetchmail: WARNING: Running as root is discouraged. Old UID list from localhost: <empty> Scratch list of UIDs: <empty> fetchmail: 6.3.19 querying localhost (protocol IMAP) at Tue 03 Jul 2012 09:46:36 AM EDT: poll started Trying to connect to 127.0.0.1/1143...connected. fetchmail: IMAP< * OK [CAPABILITY IMAP4REV1 AUTH=LOGIN] IMAP4rev1 DavMail 3.9.7-1870 server ready fetchmail: IMAP> A0001 CAPABILITY fetchmail: IMAP< * CAPABILITY IMAP4REV1 AUTH=LOGIN fetchmail: IMAP< A0001 OK CAPABILITY completed fetchmail: Protocol identified as IMAP4 rev 1 fetchmail: GSSAPI error gss_inquire_cred: Unspecified GSS failure. Minor code may provide more information fetchmail: GSSAPI error gss_inquire_cred: fetchmail: No suitable GSSAPI credentials found. Skipping GSSAPI authentication. fetchmail: If you want to use GSSAPI, you need credentials first, possibly from kinit. fetchmail: IMAP> A0002 LOGIN "domain\\user" * fetchmail: IMAP< A0002 OK Authenticated fetchmail: selecting or re-polling default folder fetchmail: IMAP> A0003 SELECT "INBOX" fetchmail: IMAP< * 1 EXISTS fetchmail: IMAP< * 1 RECENT fetchmail: IMAP< * OK [UIDVALIDITY 1] fetchmail: IMAP< * OK [UIDNEXT 344] fetchmail: IMAP< * FLAGS (\Answered \Deleted \Draft \Flagged \Seen $Forwarded Junk) fetchmail: IMAP< * OK [PERMANENTFLAGS (\Answered \Deleted \Draft \Flagged \Seen $Forwarded Junk)] fetchmail: IMAP< A0003 OK [READ-WRITE] SELECT completed fetchmail: 1 message waiting after first poll fetchmail: IMAP> A0004 EXPUNGE fetchmail: IMAP< A0004 OK EXPUNGE completed fetchmail: 1 message waiting after expunge fetchmail: IMAP> A0005 SEARCH UNSEEN fetchmail: IMAP< * SEARCH 1 fetchmail: 1 is unseen fetchmail: IMAP< A0005 OK SEARCH completed fetchmail: 1 is first unseen 1 message for domain\user at localhost. fetchmail: IMAP> A0006 FETCH 1 RFC822.SIZE fetchmail: IMAP< * 1 FETCH (UID 343 RFC822.SIZE 1350) fetchmail: IMAP< A0006 OK FETCH completed fetchmail: IMAP> A0007 FETCH 1 RFC822.HEADER fetchmail: IMAP< * 1 FETCH (UID 343 RFC822.HEADER {1350} reading message domain\user@localhost:1 of 1 (1350 header octets) fetchmail: about to deliver with: /usr/bin/procmail -f '[email protected]' -d 'root' # fetchmail: IMAP< fetchmail: IMAP< fetchmail: IMAP< Bonne journ=E9e.. fetchmail: IMAP< fetchmail: IMAP< Company Name fetchmail: IMAP< My Name fetchmail: IMAP< IT fetchmail: IMAP< Tel: (XXX) XXX-XXXX xXXX fetchmail: IMAP< www.domain.com=20 fetchmail: IMAP< fetchmail: IMAP< fetchmail: IMAP< -----Message d'origine----- fetchmail: IMAP< De=A0: User [mailto:[email protected]]=20 fetchmail: IMAP< Envoy=E9=A0: 2 juillet 2012 15:50 fetchmail: IMAP< =C0=A0: Informatique fetchmail: IMAP< Objet=A0: PROBLEM: photo fetchmail: IMAP< fetchmail: IMAP< Notification Type: PROBLEM fetchmail: IMAP< Author:=20 fetchmail: IMAP< Comment:=20 fetchmail: IMAP< fetchmail: IMAP< Host: Photos fetchmail: IMAP< Hostname: photo fetchmail: IMAP< State: DOWN fetchmail: IMAP< Address: XXX.XX.X.XX fetchmail: IMAP< fetchmail: IMAP< Date/Time: Mon Jul 2 15:49:38 EDT 2012 fetchmail: IMAP< fetchmail: IMAP< Info: CRITICAL - XXX.XX.X.XX: rta nan, lost 100% fetchmail: IMAP< fetchmail: IMAP< fetchmail: IMAP< ) fetchmail: IMAP< A0007 OK FETCH completed fetchmail: IMAP> A0008 FETCH 1 BODY.PEEK[TEXT] fetchmail: IMAP< * 1 FETCH (UID 343 BODY[TEXT] {539} (539 body octets) ******************************* fetchmail: IMAP< ) fetchmail: IMAP< A0008 OK FETCH completed flushed fetchmail: IMAP> A0009 STORE 1 +FLAGS (\Seen \Deleted) fetchmail: IMAP< * 1 FETCH (UID 343 FLAGS (\Seen \Deleted)) fetchmail: IMAP< * 1 EXPUNGE fetchmail: IMAP< A0009 OK STORE completed fetchmail: IMAP> A0010 EXPUNGE fetchmail: IMAP< A0010 OK EXPUNGE completed fetchmail: mail expunge mismatch (0 actual != 1 expected) fetchmail: IMAP> A0011 LOGOUT fetchmail: IMAP< * BYE Closing connection fetchmail: IMAP< A0011 OK LOGOUT completed fetchmail: client/server synchronization error while fetching from domain\user@localhost fetchmail: 6.3.19 querying localhost (protocol IMAP) at Tue 03 Jul 2012 09:46:36 AM EDT: poll completed Merged UID list from localhost: <empty> fetchmail: Query status=7 (ERROR) fetchmail: normal termination, status 7

    Read the article

  • Summit Time!

    - by Ajarn Mark Caldwell
    Boy, how time flies!  I can hardly believe that the 2011 PASS Summit is just one week away.  Maybe it snuck up on me because it’s a few weeks earlier than last year.  Whatever the cause, I am really looking forward to next week.  The PASS Summit is the largest SQL Server conference in the world and a fantastic networking opportunity thrown in for no additional charge.  Here are a few thoughts to help you maximize the week. Networking As Karen Lopez (blog | @DataChick) mentioned in her presentation for the Professional Development Virtual Chapter just a couple of weeks ago, “Don’t wait until you need a new job to start networking.”  You should always be working on your professional network.  Some people, especially technical-minded people, get confused by the term networking.  The first image that used to pop into my head was the image of some guy standing, awkwardly, off to the side of a cocktail party, trying to shmooze those around him.  That’s not what I’m talking about.  If you’re good at that sort of thing, and you can strike up a conversation with some stranger and learn all about them in 5 minutes, and walk away with your next business deal all but approved by the lawyers, then congratulations.  But if you’re not, and most of us are not, I have two suggestions for you.  First, register for Don Gabor’s 2-hour session on Tuesday at the Summit called Networking to Build Business Contacts.  Don is a master at small talk, and at teaching others, and in just those two short hours will help you with important tips about breaking the ice, remembering names, and smooth transitions into and out of conversations.  Then go put that great training to work right away at the Tuesday night Welcome Reception and meet some new people; which is really my second suggestion…just meet a few new people.  You see, “networking” is about meeting new people and being friendly without trying to “work it” to get something out of the relationship at this point.  In fact, Don will tell you that a better way to build the connection with someone is to look for some way that you can help them, not how they can help you. There are a ton of opportunities as long as you follow this one key point: Don’t stay in your hotel!  At the least, get out and go to the free events such as the Tuesday night Welcome Reception, the Wednesday night Exhibitor Reception, and the Thursday night Community Appreciation Party.  All three of these are perfect opportunities to meet other professionals with a similar job or interest as you, and you never know how that may help you out in the future.  Maybe you just meet someone to say HI to at breakfast the next day instead of eating alone.  Or maybe you cross paths several times throughout the Summit and compare notes on different sessions you attended.  And you just might make new friends that you look forward to seeing year after year at the Summit.  Who knows, it might even turn out that you have some specific experience that will help out that other person a few months’ from now when they run into the same challenge that you just overcame, or vice-versa.  But the point is, if you don’t get out and meet people, you’ll never have the chance for anything else to happen in the future. One more tip for shy attendees of the Summit…if you can’t bring yourself to strike up conversation with strangers at these events, then at the least, after you sit through a good session that helps you out, go up to the speaker and introduce yourself and thank them for taking the time and effort to put together their presentation.  Ideally, when you do this, tell them WHY it was beneficial to you (e.g. “Now I have a new idea of how to tackle a problem back at the office.”)  I know you think the speakers are all full of confidence and are always receiving a ton of accolades and applause, but you’re wrong.  Most of them will be very happy to hear first-hand that all the work they put into getting ready for their presentation is paying off for somebody. Training With over 170 technical sessions at the Summit, training is what it’s all about, and the training is fantastic!  Of course there are the big-name trainers like Paul Randall, Kimberly Tripp, Kalen Delaney, Itzik Ben-Gan and several others, but I am always impressed by the quality of the training put on by so many other “regular” members of the SQL Server community.  It is amazing how you don’t have to be a published author or otherwise recognized as an “expert” in an area in order to make a big impact on others just by sharing your personal experience and lessons learned.  I would rather hear the story of, and lessons learned from, “some guy or gal” who has actually been through an issue and came out the other side, than I would a trained professor who is speaking just from theory or an intellectual understanding of a topic. In addition to the three full days of regular sessions, there are also two days of pre-conference intensive training available.  There is an extra cost to this, but it is a fantastic opportunity.  Think about it…you’re already coming to this area for training, so why not extend your stay a little bit and get some in-depth training on a particular topic or two?  I did this for the first time last year.  I attended one day of extra training and it was well worth the time and money.  One of the best reasons for it is that I am extremely busy at home with my regular job and family, that it was hard to carve out the time to learn about the topic on my own.  It worked out so well last year that I am doubling up and doing two days or “pre-cons” this year. And then there are the DVDs.  I think these are another great option.  I used the online schedule builder to get ready and have an idea of which sessions I want to attend and when they are (much better than trying to figure this out at the last minute every day).  But the problem that I have run into (seems this happens every year) is that nearly every session block has two different sessions that I would like to attend.  And some of them have three!  ACK!  That won’t work!  What is a guy supposed to do?  Well, one option is to purchase the DVDs which are recordings of the audio and projected images from each session so you can continue to attend sessions long after the Summit is officially over.  Yes, many (possibly all) of these also get posted online and attendees can access those for no extra charge, but those are not necessarily all available as quickly as the DVD recording are, and the DVDs are often more convenient than downloading, especially if you want to share the training with someone who was not able to attend in person. Remember, I don’t make any money or get any other benefit if you buy the DVDs or from anything else that I have recommended here.  These are just my own thoughts, trying to help out based on my experiences from the 8 or so Summits I have attended.  There is nothing like the Summit.  It is an awesome experience, fantastic training, and a whole lot of fun which is just compounded if you’ll take advantage of the first part of this article and make some new friends along the way.

    Read the article

  • Problem upgrading kernel on debian 3.1

    - by exhuma
    Hi, I have a quite old box in a remote server farm. So I have no direct access. Only remote SSH (and via SSH to a serial console). I haven't updated this box in ages. Now, whenever I want to install a new package, a dependency to glibc appears. Unfortunately, the install of glibc depends on a 2.6 kernel and I am running a venerable 2.4 kernel (one more reason to upgrade). The problem is, that the install of a new kernel has an indirect (over locales) dependency to glibc. So, to install glibc, I need a new kernel. For a new kernel, I need to upgrade glibc. Essentially I am blocked. What's the best way to proceed considering I have no "hardware" access? Here's a quick transcript of the upgrade process: [green:~]% sudo aptitude install linux-image-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages are unused and will be REMOVED: gcc-4.3-base The following NEW packages will be automatically installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 module-init-tools yaird The following packages have been kept back: adduser apache2 apache2-mpm-prefork apache2-utils apache2.2-common apt apt-utils aptitude autoconf autotools-dev awstats base-files base-passwd [...snip...] util-linux vacation vim vim-common wamerican wbritish wget whiptail whois wwwconfig-common zlib1g The following NEW packages will be installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 linux-image-686 module-init-tools yaird The following packages will be upgraded: hotplug libc6 2 packages upgraded, 8 newly installed, 1 to remove and 277 not upgraded. Need to get 0B/22.7MB of archives. After unpacking 52.1MB will be used. Do you want to continue? [Y/n/?] Writing extended state information... Done Preconfiguring packages ... (Reading database ... 34065 files and directories currently installed.) Preparing to replace libc6 2.3.6.ds1-13 (using .../libc6_2.7-18lenny2_i386.deb) ... Checking for services that may need to be restarted... Checking init scripts... WARNING: init script for postgresql not found. [ --- libc6 config screen appears here --- ] WARNING: POSIX threads library NPTL requires kernel version 2.6.8 or later. If you use a kernel 2.4, please upgrade it before installing glibc. The installation of a 2.6 kernel _could_ ask you to install a new libc first, this is NOT a bug, and should *NOT* be reported. In that case, please add etch sources to your /etc/apt/sources.list and run: apt-get install -t etch linux-image-2.6 Then reboot into this new kernel, and proceed with your upgrade dpkg: error processing /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb (--unpack): subprocess pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Ack! Something bad happened while installing packages. Trying to recover: dpkg: dependency problems prevent configuration of locales: locales depends on glibc-2.7-1; however: Package glibc-2.7-1 is not installed. dpkg: error processing locales (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: locales Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done Now, if I follow the instrunctions as promted I get the following. Note that I am using aptitude instead of apt-get to benefit from the better dependency tracking. I did try with apt-get first. But that let me to the same problem. [green:~]% sudo aptitude install -t etch linux-image-2.6.26-2-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done E: Unable to correct problems, you have held broken packages. E: Unable to correct dependencies, some packages cannot be installed E: Unable to resolve some dependencies! Some packages had unmet dependencies. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following packages have unmet dependencies: linux-image-2.6.26-2-686: Depends: initramfs-tools (>= 0.55) but it is not installable or yaird (>= 0.0.13) but it is not installable or linux-initramfs-tool which is a virtual package. Any ideas?

    Read the article

  • Fragment method and socket.io

    - by Tolgay Toklar
    I have a method,this method updates an array list in fragment.I can call this method in main activity like this public void getFromUser(String message) { addMessageToFragment("ok"); } public void addMessageToFragment(String message) { Log.w("Step 1",message); frgObj.addMessageToList("asd"); } getFromUser is calling from fragment(when user presses the button) this is working as well.But I am using socket.io in my app,when I try to call this method from socket.io,app is not working. public void on(String event, IOAcknowledge ack, Object... args) { try{ addMessageToFragment("ok"); } catch (JSONException e) {} } When this callback function calls,app is giving this errors: 08-19 11:57:24.813: W/System.err(4962): io.socket.SocketIOException: Exception was thrown in on(String, JSONObject[]). 08-19 11:57:24.813: W/System.err(4962): Message was: 5:::{"name":"listele","args":[{"mesaj":"123","gonderen":"781722165-tolgay007-DKSMIcIYGahPuKXriM83","alici":"tolgay007","blck_id":"781722165-tolgay007","out_username":"Anony-781722","ars_status":1,"longinf":"3aqghef","a_status":1}]} 08-19 11:57:24.813: W/System.err(4962): at io.socket.IOConnection.transportMessage(IOConnection.java:702) 08-19 11:57:24.813: W/System.err(4962): at io.socket.WebsocketTransport.onMessage(WebsocketTransport.java:82) 08-19 11:57:24.813: W/System.err(4962): at org.java_websocket.client.WebSocketClient.onWebsocketMessage(WebSocketClient.java:361) 08-19 11:57:24.813: W/System.err(4962): at org.java_websocket.WebSocketImpl.deliverMessage(WebSocketImpl.java:565) 08-19 11:57:24.813: W/System.err(4962): at org.java_websocket.WebSocketImpl.decodeFrames(WebSocketImpl.java:331) 08-19 11:57:24.813: W/System.err(4962): at org.java_websocket.WebSocketImpl.decode(WebSocketImpl.java:152) 08-19 11:57:24.813: W/System.err(4962): at org.java_websocket.client.WebSocketClient.interruptableRun(WebSocketClient.java:247) 08-19 11:57:24.823: W/System.err(4962): at org.java_websocket.client.WebSocketClient.run(WebSocketClient.java:193) 08-19 11:57:24.823: W/System.err(4962): at java.lang.Thread.run(Thread.java:841) 08-19 11:57:24.823: W/System.err(4962): Caused by: android.view.ViewRootImpl$CalledFromWrongThreadException: Only the original thread that created a view hierarchy can touch its views. 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewRootImpl.checkThread(ViewRootImpl.java:6094) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewRootImpl.focusableViewAvailable(ViewRootImpl.java:2800) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.ViewGroup.focusableViewAvailable(ViewGroup.java:650) 08-19 11:57:24.823: W/System.err(4962): at android.view.View.setFlags(View.java:8878) 08-19 11:57:24.823: W/System.err(4962): at android.view.View.setFocusableInTouchMode(View.java:6114) 08-19 11:57:24.823: W/System.err(4962): at android.widget.AdapterView.checkFocus(AdapterView.java:718) 08-19 11:57:24.823: W/System.err(4962): at android.widget.AdapterView$AdapterDataSetObserver.onChanged(AdapterView.java:813) 08-19 11:57:24.823: W/System.err(4962): at android.widget.AbsListView$AdapterDataSetObserver.onChanged(AbsListView.java:6280) 08-19 11:57:24.823: W/System.err(4962): at android.database.DataSetObservable.notifyChanged(DataSetObservable.java:37) 08-19 11:57:24.823: W/System.err(4962): at android.widget.BaseAdapter.notifyDataSetChanged(BaseAdapter.java:50) 08-19 11:57:24.823: W/System.err(4962): at android.widget.ArrayAdapter.notifyDataSetChanged(ArrayAdapter.java:286) 08-19 11:57:24.823: W/System.err(4962): at com.impact.ribony.ConversationFragment.addMessageToList(ConversationFragment.java:91) 08-19 11:57:24.823: W/System.err(4962): at com.impact.ribony.MainActivity.addMessageToFragment(MainActivity.java:344) 08-19 11:57:24.823: W/System.err(4962): at com.impact.ribony.MainActivity$2.on(MainActivity.java:183) 08-19 11:57:24.823: W/System.err(4962): at io.socket.IOConnection.on(IOConnection.java:908) 08-19 11:57:24.883: W/System.err(4962): at io.socket.IOConnection.transportMessage(IOConnection.java:697) I didn't understand this error.What can be cause this error ?

    Read the article

  • SOLVED Install MythTV & 11.10 on Lenovo S12 (Intel atom) with wireless

    - by keepitsimpleengineer
    This is how I installed Ubuntu 11.10 and MythTV client on my Lenovo S12 (Intel Atom) laptop and use it using WiFi (see additional notes at end). I did this because the upgrade from 11.04 bricked the laptop. Note that the partitions on the Lenovo standard disk were already in place for this installation. Also note that my LAN is setup for fixed IP addresses. Downloaded and burned 11.10 x86 Desktop Ubuntu CD Connected the power supply cord, LAN wire and the external DVD USB drive. Ran Windows XP and made sure performance level "Performance" was set and "Wireless" was enabled. Booted S12 from CD Disabled Networking from icon on upper left panel icon Edited Connections… "Wired connection 1" ? Set IP address, accepted default netmask and set gateway. Also set DNS server. Good idea to check "Connection Information" here to verify everything's O.K. Selected Install Ubuntu from the initial "Install" window Verified the three items were checked (required disk space available, plugged into a power source, & connected to the Internet) Selected Download updates while installing and third party software. Hit Continue… At wireless selected don't want to connect…WiFi…now. Continue… At Installation type, selected Something else. Continue… At partition tale, selected the ext4 Linux partition, set the mount point as "/", and marked for formatting. Here I selected the main disk (/sda) for installing the boot manager. Continue… Selected or verified my Time zone. Continue… Selected my keyboard layout. Continue… Filled in the who are you fields. Make sure password is required to sign in is checked. Continue… Chose a picture. Continue… I selected import no accounts. Continue… Wait as the Install creeps along. If your screen goes blank, tap the space bar ? apparently the screen saver/power plan does this. There are several progress bars. The longest was "Installing system", and it was the next to the last one. Installation Complete window appears, Restart Now… Wait as it stops, The screen blanks then the message "…remove…media…close tray…press enter" I just unplugged the USB DVD and hit enter… It was disheartening but the screen turned Ubuntu Purple-beige and nothing happened, so I help down the power key until it shut down, the pressed it again and the Grub Boot screen appeared. Select Ubuntu… 25.The screen went blank with the little flashing underscore cursor on it and the disk light would occasionally flash. I hit the enter key and eventuality Ubuntu started. After a somewhat long time the unity desktop appeared. 11.10, unlike earlier versions, retains the connection information. Check this by checking the network icon on the upper left applet panel. Here the touch-pad·mouse quit working and I had to reboot. It takes and extremely long time to boot, sometimes requiring several power off/ power on (cold boot). You can try to get the default network manager to work, but it might not, it didn't on mine for WiFi. Thanks to: Chris at URL here's what to do… disconnect your wired Internet connection. input your wireless information into network manager open a terminal (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "terminal". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. click to open a terminal, and type in: sudo rmmod acer_wmi && echo "blacklist acer_wmi" >> /etc/modprobe.d/blacklist.conf and hit enter. type in your password as asked. if you have correctly entered your WiFi information and you are near your AP, you should connect immediately if not, see the URL above ? you might need to replace "network manager" with "wicd" ? I did with 11.04. Update the new 11.10, in the upper left panel applet weird·gear icon is menu with a line about updating. It's the new way to invoke Update Manager. Your lenovo S12 (intel atom) should now run the new unity Ubuntu. Point your elbow at the ceiling and pat yourself on the back. Installing Mythbuntu Client 24.1 Open mythbuntu.org/repos (I urge you not to directly use Ubuntu Software Center for this) Install Mythbuntu Repos Save the file (in ~/Downloads, the default) Run the file ? it will update your repositories so that you will get the proper installation sources ? it will start Ubuntu Software Center to do this ? Click Install… You will need your password. Debconf window will open, select by making sure check mark is in the little box "Would you like to activate…". Forward… Which version? At the time of writing the current "Stable" version was 24.1, select 0.24.x… Forward… Read the message, then forward… Delete the downloaded file. Install synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "synaptic". Click on the synaptic icon. Ubuntu Software Center will open and allow you to install synaptic package manager. Open Synaptic (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "Synaptic". Might be a good idea to drag and drop the terminal icon to the terminal, it's easy to get rid of later. Run synaptic, read the intro, and close the intro window. Type in mythbuntu-control-centre in the Quick filter text box, and then select it "Mark for installation" by clicking on the box next to it's name. Marvel at the additional to be installed items, then select "?Mark"… At the top of the synaptic window click on the "? Apply" button. Marvel at the amount of stuff to be installed, the click on "Apply". When finished, close finished window and synaptic. Open mythbuntu-control-centre (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythbuntu". Might be a good idea to drag and drop the mythbuntu-control-centre icon to the terminal, it's easy to get rid of later. You can now configure and install the frontend. Go down the icon totem on the right side of the window and click as needed… System roles. ? No Backend, Desktop Frontend, and Ubuntu Desktop. Apply… & Apply changes… & Password… MySQL Configuration ? from backend ? Setup General Alt-N(ext) Alt-N(ext) Stetting Access Setup PIN code: ~~~~ Input Security key and click "Test Connection", if ?, then Apply… & Apply… {note: for some inexplicable reason, control centre hung on this, but when I restarted it, it was set properly} Graphics drivers, When I did this, only the Broadcom wireless driver showed up. I closed without doing anything. Services. I enabled SSH & Samba. Apply… & Apply… Repositories. Asked & Answered. MythExport. Pass, I believe it requires backend on the same system. Proprietary Codec Support. Check to enable, Apply… & Apply… System Updates. No action necessary, will be a part of the Ubuntu update mechanism. Themes and Artwork. For themes, I selected Enable/Update all. Apply… & Apply… Infrared & Startup behavior and Plugins. Defer until you know more. Close software centre. Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Incorrect Group Membership. Fix this by clicking "Yes"… Log out/end. Do this by clicking "Yes"… For my Lenovo S12, I had to manually restart Ubuntu - and still with the very long restart…/no start/cold boot/reboot/pressing the shift key required Open mythTV (unity dash, top of icon totem, open, and make sure the ruler&pen icon on the bottom is selected, 2nd from left) type in "mythTV". Might be a good idea to drag and drop the mythTV icon to the terminal, it's easy to get rid of later. Will open with Select country & language. Do so. then get message with "No", hit "Ok" and arrive at the data base Configuration 1/2 screen. You will need your brackend password, from backend ? Setup General Database Configuration 1/2 Password:~? Enter this Hit Alt-n to go to the next page. Select "Use custom id…", then enter a custom ID, I use the machine's name. Hit finish, and MythTV should start up with all default settings. For the lenovo S12, the first thing you want to do is to set Playback profiles to "Normal". From Setup TV Settings Playback Alt-N(ext) Alt-N(ext) Playback Profiles (3/8) : Change Current Video Playback Profile to "Normal". You can fiddle with this setting later. For the lenovo S12, the second thing is to get the sound going. From Setup General Alt-N(ext) Alt-N(ext) Alt-N(ext) Audio System: The top of the screen is a button title "Scan for audio devices", move the highlight there and press the Space bar. Then Tab down to Audio Output Device: and left-right arrow until "ALSA:hw:Card=Intel,DEV=0" is selected. Then Alt-N(ext) until "Finish". Now you should have sound. You should now have MythTV working nicely on the Lenovo S12 Notes about wireless: Running Lenovo S12 on wireless is demanding on both power and WiFi connection. Best results will be obtained when running on power and wired connection. I run my S12 on wireless, actually two serial connections with two access points, something that is not easy to achieve. Here Mythbuntu client-server (in den) <? wireless link 1 <?office LAN? wireless link 2 <? Lenovo S12 Ubuntu 11.10 The office LAN is fixed IP behind an Untangle firewall router. There is another MythTV client on Ubuntu 10.10 computer in the office (which has always worked well). ProblemMythbuntu\Win7 client hangs with frozen frames, short segment of audio repeating. Hardware Rosewill RNX-G300EX IEEE 802.11b/g PCI Wireless Card on client-server 2 Linksys WRT54GL wireless broadband routers on LAN for link1 and link 2 WRT54GL FirmwareDD-WRT v24-sp2(07/22/09) voip set up to act as an access point. Note? many people advised this was an unworkable scheme, and in probably most cases it will be. Solution? Set up DD-WRT with the following Wireless settings… Basic Channel: Different fixed channels at least 4 difference, I use 6 & 11 Basic Sensitivity Range (ACK timing): 50 MAC filter use filter: Enable, Selected Permit only clients listed to access… Requires adding MAC addresses in "Edit MAC Filter List" This causes the 54GL's to ignore any but the listed MAC address, down side, no "guest" capability. Advanced Basic rate: All Advanced CTS Protection Mode: Off Advanced Frame Burst: Enable Advanced Max associate clients: 4 for client link 2, 1 for client-server link 1 Advanced AP isolation: Enable Advanced Preamble: Short Advanced Afterburner: On Advanced Wireless GUI access: Off Advanced WMM support: Off Other settings: default for supplied firmware. Why I suspect this worked? The 54GL Access Points's with the firmware's setting are set to handle a multiple client, wide area situation. With these mods I reconfigured them for a small area, few client situation, disabling Advanced WMM probably the most important. In addition, the client mythtv when used all other users of its access point are turned off except for a Skype phone. Also, the client-server is set up to allow other connections though it's LAN connection, and these are used to connect the TV and disc players, not used when client is being used.

    Read the article

  • Oracle Coherence, Split-Brain and Recovery Protocols In Detail

    - by Ricardo Ferreira
    This article provides a high level conceptual overview of Split-Brain scenarios in distributed systems. It will focus on a specific example of cluster communication failure and recovery in Oracle Coherence. This includes a discussion on the witness protocol (used to remove failed cluster members) and the panic protocol (used to resolve Split-Brain scenarios). Note that the removal of cluster members does not necessarily indicate a Split-Brain condition. Oracle Coherence does not (and cannot) detect a Split-Brain as it occurs, the condition is only detected when cluster members that previously lost contact with each other regain contact. Cluster Topology and Configuration In order to create an good didactic for the article, let's assume a cluster topology and configuration. In this example we have a six member cluster, consisting of one JVM on each physical machine. The member IDs are as follows: Member ID  IP Address  1  10.149.155.76  2  10.149.155.77  3  10.149.155.236  4  10.149.155.75  5  10.149.155.79  6  10.149.155.78 Members 1, 2, and 3 are connected to a switch, and members 4, 5, and 6 are connected to a second switch. There is a link between the two switches, which provides network connectivity between all of the machines. Member 1 is the first member to join this cluster, thus making it the senior member. Member 6 is the last member to join this cluster. Here is a log snippet from Member 6 showing the complete member set: 2010-02-26 15:27:57.390/3.062 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=main, member=6): Started DefaultCacheServer... SafeCluster: Name=cluster:0xDDEB Group{Address=224.3.5.3, Port=35465, TTL=4} MasterMemberSet ( ThisMember=Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) OldestMember=Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) ActualMemberSet=MemberSet(Size=6, BitSetCount=2 Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) Member(Id=2, Timestamp=2010-02-26 15:27:17.847, Address=10.149.155.77:8088, MachineId=1101, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:296, Role=CoherenceServer) Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer) Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) Member(Id=5, Timestamp=2010-02-26 15:27:49.095, Address=10.149.155.79:8088, MachineId=1103, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:3229, Role=CoherenceServer) Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) ) RecycleMillis=120000 RecycleSet=MemberSet(Size=0, BitSetCount=0 ) ) At approximately 15:30, the connection between the two switches is severed: Thirty seconds later (the default packet timeout in development mode) the logs indicate communication failures across the cluster. In this example, the communication failure was caused by a network failure. In a production setting, this type of communication failure can have many root causes, including (but not limited to) network failures, excessive GC, high CPU utilization, swapping/virtual memory, and exceeding maximum network bandwidth. In addition, this type of failure is not necessarily indicative of a split brain. Any communication failure will be logged in this fashion. Member 2 logs a communication failure with Member 5: 2010-02-26 15:30:32.638/196.928 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=PacketPublisher, member=2): Timeout while delivering a packet; requesting the departure confirmation for Member(Id=5, Timestamp=2010-02-26 15:27:49.095, Address=10.149.155.79:8088, MachineId=1103, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:3229, Role=CoherenceServer) by MemberSet(Size=2, BitSetCount=2 Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) ) The Coherence clustering protocol (TCMP) is a reliable transport mechanism built on UDP. In order for the protocol to be reliable, it requires an acknowledgement (ACK) for each packet delivered. If a packet fails to be acknowledged within the configured timeout period, the Coherence cluster member will log a packet timeout (as seen in the log message above). When this occurs, the cluster member will consult with other members to determine who is at fault for the communication failure. If the witness members agree that the suspect member is at fault, the suspect is removed from the cluster. If the witnesses unanimously disagree, the accuser is removed. This process is known as the witness protocol. Since Member 2 cannot communicate with Member 5, it selects two witnesses (Members 1 and 4) to determine if the communication issue is with Member 5 or with itself (Member 2). However, Member 4 is on the switch that is no longer accessible by Members 1, 2 and 3; thus a packet timeout for member 4 is recorded as well: 2010-02-26 15:30:35.648/199.938 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=PacketPublisher, member=2): Timeout while delivering a packet; requesting the departure confirmation for Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) by MemberSet(Size=2, BitSetCount=2 Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) ) Member 1 has the ability to confirm the departure of member 4, however Member 6 cannot as it is also inaccessible. At the same time, Member 3 sends a request to remove Member 6, which is followed by a report from Member 3 indicating that Member 6 has departed the cluster: 2010-02-26 15:30:35.706/199.996 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=2): MemberLeft request for Member 6 received from Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer) 2010-02-26 15:30:35.709/199.999 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=2): MemberLeft notification for Member 6 received from Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer) The log for Member 3 determines how Member 6 departed the cluster: 2010-02-26 15:30:35.161/191.694 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=PacketPublisher, member=3): Timeout while delivering a packet; requesting the departure confirmation for Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) by MemberSet(Size=2, BitSetCount=2 Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) Member(Id=2, Timestamp=2010-02-26 15:27:17.847, Address=10.149.155.77:8088, MachineId=1101, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:296, Role=CoherenceServer) ) 2010-02-26 15:30:35.165/191.698 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=Cluster, member=3): Member departure confirmed by MemberSet(Size=2, BitSetCount=2 Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) Member(Id=2, Timestamp=2010-02-26 15:27:17.847, Address=10.149.155.77:8088, MachineId=1101, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:296, Role=CoherenceServer) ); removing Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) In this case, Member 3 happened to select two witnesses that it still had connectivity with (Members 1 and 2) thus resulting in a simple decision to remove Member 6. Given the departure of Member 6, Member 2 is left with a single witness to confirm the departure of Member 4: 2010-02-26 15:30:35.713/200.003 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=Cluster, member=2): Member departure confirmed by MemberSet(Size=1, BitSetCount=2 Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) ); removing Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) In the meantime, Member 4 logs a missing heartbeat from the senior member. This message is also logged on Members 5 and 6. 2010-02-26 15:30:07.906/150.453 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=PacketListenerN, member=4): Scheduled senior member heartbeat is overdue; rejoining multicast group. Next, Member 4 logs a TcpRing failure with Member 2, thus resulting in the termination of Member 2: 2010-02-26 15:30:21.421/163.968 Oracle Coherence GE 3.5.3/465p2 <D4> (thread=Cluster, member=4): TcpRing: Number of socket exceptions exceeded maximum; last was "java.net.SocketTimeoutException: connect timed out"; removing the member: 2 For quick process termination detection, Oracle Coherence utilizes a feature called TcpRing which is a sparse collection of TCP/IP-based connections between different members in the cluster. Each member in the cluster is connected to at least one other member, which (if at all possible) is running on a different physical box. This connection is not used for any data transfer, only heartbeat communications are sent once a second per each link. If a certain number of exceptions are thrown while trying to re-establish a connection, the member throwing the exceptions is removed from the cluster. Member 5 logs a packet timeout with Member 3 and cites witnesses Members 4 and 6: 2010-02-26 15:30:29.791/165.037 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=PacketPublisher, member=5): Timeout while delivering a packet; requesting the departure confirmation for Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer) by MemberSet(Size=2, BitSetCount=2 Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) ) 2010-02-26 15:30:29.798/165.044 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=Cluster, member=5): Member departure confirmed by MemberSet(Size=2, BitSetCount=2 Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) Member(Id=6, Timestamp=2010-02-26 15:27:58.635, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) ); removing Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer) Eventually we are left with two distinct clusters consisting of Members 1, 2, 3 and Members 4, 5, 6, respectively. In the latter cluster, Member 4 is promoted to senior member. The connection between the two switches is restored at 15:33. Upon the restoration of the connection, the cluster members immediately receive cluster heartbeats from the two senior members. In the case of Members 1, 2, and 3, the following is logged: 2010-02-26 15:33:14.970/369.066 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=Cluster, member=1): The member formerly known as Member(Id=4, Timestamp=2010-02-26 15:30:35.341, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) has been forcefully evicted from the cluster, but continues to emit a cluster heartbeat; henceforth, the member will be shunned and its messages will be ignored. Likewise for Members 4, 5, and 6: 2010-02-26 15:33:14.343/336.890 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=Cluster, member=4): The member formerly known as Member(Id=1, Timestamp=2010-02-26 15:30:31.64, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) has been forcefully evicted from the cluster, but continues to emit a cluster heartbeat; henceforth, the member will be shunned and its messages will be ignored. This message indicates that a senior heartbeat is being received from members that were previously removed from the cluster, in other words, something that should not be possible. For this reason, the recipients of these messages will initially ignore them. After several iterations of these messages, the existence of multiple clusters is acknowledged, thus triggering the panic protocol to reconcile this situation. When the presence of more than one cluster (i.e. Split-Brain) is detected by a Coherence member, the panic protocol is invoked in order to resolve the conflicting clusters and consolidate into a single cluster. The protocol consists of the removal of smaller clusters until there is one cluster remaining. In the case of equal size clusters, the one with the older Senior Member will survive. Member 1, being the oldest member, initiates the protocol: 2010-02-26 15:33:45.970/400.066 Oracle Coherence GE 3.5.3/465p2 <Warning> (thread=Cluster, member=1): An existence of a cluster island with senior Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) containing 3 nodes have been detected. Since this Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) is the senior of an older cluster island, the panic protocol is being activated to stop the other island's senior and all junior nodes that belong to it. Member 3 receives the panic: 2010-02-26 15:33:45.803/382.336 Oracle Coherence GE 3.5.3/465p2 <Error> (thread=Cluster, member=3): Received panic from senior Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer) caused by Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer) Member 4, the senior member of the younger cluster, receives the kill message from Member 3: 2010-02-26 15:33:44.921/367.468 Oracle Coherence GE 3.5.3/465p2 <Error> (thread=Cluster, member=4): Received a Kill message from a valid Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer); stopping cluster service. In turn, Member 4 requests the departure of its junior members 5 and 6: 2010-02-26 15:33:44.921/367.468 Oracle Coherence GE 3.5.3/465p2 <Error> (thread=Cluster, member=4): Received a Kill message from a valid Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer); stopping cluster service. 2010-02-26 15:33:43.343/349.015 Oracle Coherence GE 3.5.3/465p2 <Error> (thread=Cluster, member=6): Received a Kill message from a valid Member(Id=4, Timestamp=2010-02-26 15:27:39.574, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer); stopping cluster service. Once Members 4, 5, and 6 restart, they rejoin the original cluster with senior member 1. The log below is from Member 4. Note that it receives a different member id when it rejoins the cluster. 2010-02-26 15:33:44.921/367.468 Oracle Coherence GE 3.5.3/465p2 <Error> (thread=Cluster, member=4): Received a Kill message from a valid Member(Id=3, Timestamp=2010-02-26 15:27:24.892, Address=10.149.155.236:8088, MachineId=1260, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:32459, Role=CoherenceServer); stopping cluster service. 2010-02-26 15:33:46.921/369.468 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Service Cluster left the cluster 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Invocation:InvocationService, member=4): Service InvocationService left the cluster 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=OptimisticCache, member=4): Service OptimisticCache left the cluster 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=ReplicatedCache, member=4): Service ReplicatedCache left the cluster 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=DistributedCache, member=4): Service DistributedCache left the cluster 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Invocation:Management, member=4): Service Management left the cluster 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Member 6 left service Management with senior member 5 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Member 6 left service DistributedCache with senior member 5 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Member 6 left service ReplicatedCache with senior member 5 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Member 6 left service OptimisticCache with senior member 5 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Member 6 left service InvocationService with senior member 5 2010-02-26 15:33:47.046/369.593 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=4): Member(Id=6, Timestamp=2010-02-26 15:33:47.046, Address=10.149.155.78:8088, MachineId=1102, Location=process:228, Role=CoherenceServer) left Cluster with senior member 4 2010-02-26 15:33:49.218/371.765 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=main, member=n/a): Restarting cluster 2010-02-26 15:33:49.421/371.968 Oracle Coherence GE 3.5.3/465p2 <D5> (thread=Cluster, member=n/a): Service Cluster joined the cluster with senior service member n/a 2010-02-26 15:33:49.625/372.172 Oracle Coherence GE 3.5.3/465p2 <Info> (thread=Cluster, member=n/a): This Member(Id=5, Timestamp=2010-02-26 15:33:50.499, Address=10.149.155.75:8088, MachineId=1099, Location=process:800, Role=CoherenceServer, Edition=Grid Edition, Mode=Development, CpuCount=2, SocketCount=1) joined cluster "cluster:0xDDEB" with senior Member(Id=1, Timestamp=2010-02-26 15:27:06.931, Address=10.149.155.76:8088, MachineId=1100, Location=site:usdhcp.oraclecorp.com,machine:dhcp-burlington6-4fl-east-10-149,process:511, Role=CoherenceServer, Edition=Grid Edition, Mode=Development, CpuCount=2, SocketCount=2) Cool isn't it?

    Read the article

  • FreeBSD performance tuning. Sysctls, loader.conf, kernel.

    - by SaveTheRbtz
    I wanted to share knowledge of tuning FreeBSD via sysctls, so i'm posting them with comments. Based on Igor Sysoev (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Sysctls are for 7.x FreeBSD. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. Highload web server sysctls: # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Do not use lager sockbufs on 8.0 # ( http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=262144 # Recive clusters (on amd64 7.2+ 65k is default) # For such high value vm.kmem_size must be increased to 3G #kern.ipc.nmbclusters=229376 # Jumbo pagesize(4k/8k) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=192000 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=24000 #kern.ipc.nmbjumbo16=10240 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # Turn off receive autotuning #net.inet.tcp.recvbuf_auto=0 # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This should be enabled if you going to use big spaces (>64k) #net.inet.tcp.rfc1323=1 # Turn this off on highspeed, lossless connections (LAN 1Gbit+) #net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # You can try setting it to 0 on fileserver with 1GBit+ interfaces # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) #net.inet.tcp.inflight.enable=0 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't tested it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds (default: 30000 from RFC) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=40960 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becames lower) vfs.ufs.dirhash_maxmem=67108864 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 /boot/loader.conf: # Accept filters for data, http and DNS requests # Usefull when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load= #siis_load= # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 200M) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=100 # Incresed hostcache net.inet.tcp.hostcache.hashsize="16384" net.inet.tcp.hostcache.bucketlimit="100" # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # `sysctl dev.em.0.stats=1 ; dmesg` # #Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # Nicer boot logo =) loader_logo="beastie" And finally here is my additions to GENERIC kernel # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU of 8K(amd64) # (4k for i386). This req. is only for receiving data. # Read more in man zero_copy_sockets #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL options IPFIREWALL_VERBOSE options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_DEFAULT_TO_ACCEPT options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron #device amdtemp # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # DTrace options KDTRACE_HOOKS # all architectures - enable general DTrace hooks options DDB_CTF # all architectures - kernel ELF linker loads CTF data #options KDTRACE_FRAME # amd64-only # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (9.x+) #options TEKEN_UTF8 #options TEKEN_XTERM # NCQ support # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ #options ATA_CAM # FreeBSD 9+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html #options DEADLKRES PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

    Read the article

  • FreeBSD performance tuning. Sysctls, loader.conf, kernel

    - by SaveTheRbtz
    I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

    Read the article

  • HDFS some datanodes of cluster are suddenly disconnected while reducers are running

    - by user1429825
    I have 8 slave computers and 1 master computer for running Hadoop (ver 0.21) some datanodes of cluster are suddenly disconnected while I was running MapReduce code on 10GB data After all mappers finished and around 80% of reducers was processed, randomly one or more datanode disconned from network. and then the other datanodes start to disappear from network even if I killed the MapReduce job when I found some datanode was disconnected. I've tried to change dfs.datanode.max.xcievers to 4096, turned off fire-walls of all computing node, disabled selinux and increased the number of file open limit to 20000 but they didn't work at all... anyone have a idea to solve this problem? followings are error log from mapreduce 12/06/01 12:31:29 INFO mapreduce.Job: Task Id : attempt_201206011227_0001_r_000006_0, Status : FAILED java.io.IOException: Bad connect ack with firstBadLink as ***.***.***.148:20010 at org.apache.hadoop.hdfs.DFSOutputStream$DataStreamer.createBlockOutputStream(DFSOutputStream.java:889) at org.apache.hadoop.hdfs.DFSOutputStream$DataStreamer.nextBlockOutputStream(DFSOutputStream.java:820) at org.apache.hadoop.hdfs.DFSOutputStream$DataStreamer.run(DFSOutputStream.java:427) and followings are logs from datanode 2012-06-01 13:01:01,118 INFO org.apache.hadoop.hdfs.server.datanode.DataNode: Receiving block blk_-5549263231281364844_3453 src: /*.*.*.147:56205 dest: /*.*.*.142:20010 2012-06-01 13:01:01,136 INFO org.apache.hadoop.hdfs.server.datanode.DataNode: DatanodeRegistration(*.*.*.142:20010, storageID=DS-1534489105-*.*.*.142-20010-1337757934836, infoPort=20075, ipcPort=20020) Starting thread to transfer block blk_-3849519151985279385_5906 to *.*.*.147:20010 2012-06-01 13:01:19,135 WARN org.apache.hadoop.hdfs.server.datanode.DataNode: DatanodeRegistration(*.*.*.142:20010, storageID=DS-1534489105-*.*.*.142-20010-1337757934836, infoPort=20075, ipcPort=20020):Failed to transfer blk_-5797481564121417802_3453 to *.*.*.146:20010 got java.net.ConnectException: > Connection timed out at sun.nio.ch.SocketChannelImpl.checkConnect(Native Method) at sun.nio.ch.SocketChannelImpl.finishConnect(SocketChannelImpl.java:701) at org.apache.hadoop.net.SocketIOWithTimeout.connect(SocketIOWithTimeout.java:206) at org.apache.hadoop.net.NetUtils.connect(NetUtils.java:373) at org.apache.hadoop.hdfs.server.datanode.DataNode$DataTransfer.run(DataNode.java:1257) at java.lang.Thread.run(Thread.java:722) 2012-06-01 13:06:20,342 INFO org.apache.hadoop.hdfs.server.datanode.DataBlockScanner: Verification succeeded for blk_6674438989226364081_3453 2012-06-01 13:09:01,781 WARN org.apache.hadoop.hdfs.server.datanode.DataNode: DatanodeRegistration(*.*.*.142:20010, storageID=DS-1534489105-*.*.*.142-20010-1337757934836, infoPort=20075, ipcPort=20020):Failed to transfer blk_-3849519151985279385_5906 to *.*.*.147:20010 got java.net.SocketTimeoutException: 480000 millis timeout while waiting for channel to be ready for write. ch : java.nio.channels.SocketChannel[connected local=/*.*.*.142:60057 remote=/*.*.*.147:20010] at org.apache.hadoop.net.SocketIOWithTimeout.waitForIO(SocketIOWithTimeout.java:246) at org.apache.hadoop.net.SocketOutputStream.waitForWritable(SocketOutputStream.java:164) at org.apache.hadoop.net.SocketOutputStream.transferToFully(SocketOutputStream.java:203) at org.apache.hadoop.hdfs.server.datanode.BlockSender.sendChunks(BlockSender.java:388) at org.apache.hadoop.hdfs.server.datanode.BlockSender.sendBlock(BlockSender.java:476) at org.apache.hadoop.hdfs.server.datanode.DataNode$DataTransfer.run(DataNode.java:1284) at java.lang.Thread.run(Thread.java:722) hdfs-site.xml <configuration> <property> <name>dfs.name.dir</name> <value>/home/hadoop/data/name</value> </property> <property> <name>dfs.data.dir</name> <value>/home/hadoop/data/hdfs1,/home/hadoop/data/hdfs2,/home/hadoop/data/hdfs3,/home/hadoop/data/hdfs4,/home/hadoop/data/hdfs5</value> </property> <property> <name>dfs.replication</name> <value>3</value> </property> <property> <name>dfs.datanode.max.xcievers</name> <value>4096</value> </property> <property> <name>dfs.http.address</name> <value>0.0.0.0:20070</value> <description>50070 The address and the base port where the dfs namenode web ui will listen on. If the port is 0 then the server will start on a free port. </description> </property> <property> <name>dfs.datanode.http.address</name> <value>0.0.0.0:20075</value> <description>50075 The datanode http server address and port. If the port is 0 then the server will start on a free port. </description> </property> <property> <name>dfs.secondary.http.address</name> <value>0.0.0.0:20090</value> <description>50090 The secondary namenode http server address and port. If the port is 0 then the server will start on a free port. </description> </property> <property> <name>dfs.datanode.address</name> <value>0.0.0.0:20010</value> <description>50010 The address where the datanode server will listen to. If the port is 0 then the server will start on a free port. </description> <property> <name>dfs.datanode.ipc.address</name> <value>0.0.0.0:20020</value> <description>50020 The datanode ipc server address and port. If the port is 0 then the server will start on a free port. </description> </property> <property> <name>dfs.datanode.https.address</name> <value>0.0.0.0:20475</value> </property> <property> <name>dfs.https.address</name> <value>0.0.0.0:20470</value> </property> </configuration> mapred-site.xml <configuration> <property> <name>mapred.job.tracker</name> <value>masternode:29001</value> </property> <property> <name>mapred.system.dir</name> <value>/home/hadoop/data/mapreduce/system</value> </property> <property> <name>mapred.local.dir</name> <value>/home/hadoop/data/mapreduce/local</value> </property> <property> <name>mapred.map.tasks</name> <value>32</value> <description> default number of map tasks per job.</description> </property> <property> <name>mapred.tasktracker.map.tasks.maximum</name> <value>4</value> </property> <property> <name>mapred.reduce.tasks</name> <value>8</value> <description> default number of reduce tasks per job.</description> </property> <property> <name>mapred.map.child.java.opts</name> <value>-Xmx2048M</value> </property> <property> <name>io.sort.mb</name> <value>500</value> </property> <property> <name>mapred.task.timeout</name> <value>1800000</value> <!-- 30 minutes --> </property> <property> <name>mapred.job.tracker.http.address</name> <value>0.0.0.0:20030</value> <description> 50030 The job tracker http server address and port the server will listen on. If the port is 0 then the server will start on a free port. </description> </property> <property> <name>mapred.task.tracker.http.address</name> <value>0.0.0.0:20060</value> <description> 50060 </property> </configuration>

    Read the article

  • Jdbc - Connect remote Mysql Database error

    - by Guilherme Ruiz
    I'm using JDBC to connect my program to a MySQL database. I already put the port number and yes, my database have permission to access. When i use localhost work perfectly, but when i try connect to a remote MySQL database, show this error on console. java.lang.ExceptionInInitializerError Caused by: java.lang.NumberFormatException: null at java.lang.Integer.parseInt(Integer.java:454) at java.lang.Integer.parseInt(Integer.java:527) at serial.BDArduino.<clinit>(BDArduino.java:25) Exception in thread "main" Java Result: 1 CONSTRUÍDO COM SUCESSO (tempo total: 1 segundo) Thank you in Advance ! MAIN CODE /* * To change this template, choose Tools | Templates * and open the template in the editor. */ package serial; import gnu.io.CommPort; import gnu.io.CommPortIdentifier; import gnu.io.SerialPort; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.io.IOException; import java.io.InputStream; import java.io.OutputStream; import javax.swing.JFrame; import javax.swing.JOptionPane; /** * * @author Ruiz */ public class BDArduino extends JFrame { static boolean connected = false; static int aux_sql8 = Integer.parseInt(Sql.getDBinfo("SELECT * FROM arduinoData WHERE id=1", "pin8")); static int aux_sql2 = Integer.parseInt(Sql.getDBinfo("SELECT * FROM arduinoData WHERE id=1", "pin2")); CommPort commPort = null; SerialPort serialPort = null; InputStream inputStream = null; static OutputStream outputStream = null; String comPortNum = "COM10"; int baudRate = 9600; int[] intArray = {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13}; /** * Creates new form ArduinoTest */ public BDArduino() { //super("Arduino Test App"); initComponents(); } class Escrita extends Thread { private int i; public void run() { while (true) { System.out.println("Número :" + i++); } } } //public void actionPerformed(ActionEvent e) { // String arg = e.getActionCommand(); public static void writeData(int a) throws IOException { outputStream.write(a); } public void action(String arg) { System.out.println(arg); Object[] msg = {"Baud Rate: ", "9600", "COM Port #: ", "COM10"}; if (arg == "connect") { if (connected == false) { new BDArduino.ConnectionMaker().start(); } else { closeConnection(); } } if (arg == "disconnect") { serialPort.close(); closeConnection(); } if (arg == "p2") { System.out.print("Pin #2\n"); try { outputStream.write(intArray[0]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p3") { System.out.print("Pin #3\n"); try { outputStream.write(intArray[1]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p4") { System.out.print("Pin #4\n"); try { outputStream.write(intArray[2]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p5") { System.out.print("Pin #5\n"); try { outputStream.write(intArray[3]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p6") { System.out.print("Pin #6\n"); try { outputStream.write(intArray[4]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p7") { System.out.print("Pin #7\n"); try { outputStream.write(intArray[5]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p8") { System.out.print("Pin #8\n"); try { outputStream.write(intArray[6]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p9") { System.out.print("Pin #9\n"); try { outputStream.write(intArray[7]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p10") { System.out.print("Pin #10\n"); try { outputStream.write(intArray[8]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p11") { System.out.print("Pin #11\n"); try { outputStream.write(intArray[9]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p12") { System.out.print("Pin #12\n"); try { outputStream.write(intArray[10]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } if (arg == "p13") { System.out.print("Pin #12\n"); try { outputStream.write(intArray[11]); }//end try catch (IOException e12) { e12.printStackTrace(); System.exit(-1); }//end catch } } //******************************************************* //Arduino Connection *************************************** //****************************************************** void closeConnection() { try { outputStream.close(); } catch (Exception ex) { ex.printStackTrace(); String cantCloseConnectionMessage = "Can't Close Connection!"; JOptionPane.showMessageDialog(null, cantCloseConnectionMessage, "ERROR", JOptionPane.ERROR_MESSAGE); } connected = false; System.out.print("\nDesconectado\n"); String disconnectedConnectionMessage = "Desconectado!"; JOptionPane.showMessageDialog(null, disconnectedConnectionMessage, "Desconectado", JOptionPane.INFORMATION_MESSAGE); }//end closeConnection() void connect() throws Exception { String portName = comPortNum; CommPortIdentifier portIdentifier = CommPortIdentifier.getPortIdentifier(portName); if (portIdentifier.isCurrentlyOwned()) { System.out.println("Error: Port is currently in use"); String portInUseConnectionMessage = "Port is currently in use!\nTry Again Later..."; JOptionPane.showMessageDialog(null, portInUseConnectionMessage, "ERROR", JOptionPane.ERROR_MESSAGE); } else { commPort = portIdentifier.open(this.getClass().getName(), 2000); if (commPort instanceof SerialPort) { serialPort = (SerialPort) commPort; serialPort.setSerialPortParams(baudRate, SerialPort.DATABITS_8, SerialPort.STOPBITS_1, SerialPort.PARITY_NONE); outputStream = serialPort.getOutputStream(); } else { System.out.println("Error: Only serial ports are handled "); String onlySerialConnectionMessage = "Serial Ports ONLY!"; JOptionPane.showMessageDialog(null, onlySerialConnectionMessage, "ERROR", JOptionPane.ERROR_MESSAGE); } }//end else //wait some time try { Thread.sleep(300); } catch (InterruptedException ie) { } }//end connect //******************************************************* //*innerclasses****************************************** //******************************************************* public class ConnectionMaker extends Thread { public void run() { //try to make a connection try { connect(); } catch (Exception ex) { ex.printStackTrace(); System.out.print("ERROR: Cannot connect!"); String cantConnectConnectionMessage = "Cannot Connect!\nCheck the connection settings\nand/or your configuration\nand try again!"; JOptionPane.showMessageDialog(null, cantConnectConnectionMessage, "ERROR", JOptionPane.ERROR_MESSAGE); } //show status serialPort.notifyOnDataAvailable(true); connected = true; //send ack System.out.print("\nConnected\n"); String connectedConnectionMessage = "Conectado!"; JOptionPane.showMessageDialog(null, connectedConnectionMessage, "Conectado", JOptionPane.INFORMATION_MESSAGE); }//end run }//end ConnectionMaker /** * This method is called from within the constructor to initialize the form. * WARNING: Do NOT modify this code. The content of this method is always * regenerated by the Form Editor. */ @SuppressWarnings("unchecked") // <editor-fold defaultstate="collapsed" desc="Generated Code"> private void initComponents() { btnp2 = new javax.swing.JButton(); btncon = new javax.swing.JButton(); btndesc = new javax.swing.JButton(); btnp3 = new javax.swing.JButton(); btnp4 = new javax.swing.JButton(); btnp5 = new javax.swing.JButton(); btnp9 = new javax.swing.JButton(); btnp6 = new javax.swing.JButton(); btnp7 = new javax.swing.JButton(); btnp8 = new javax.swing.JButton(); btn13 = new javax.swing.JButton(); btnp10 = new javax.swing.JButton(); btnp11 = new javax.swing.JButton(); btnp12 = new javax.swing.JButton(); setDefaultCloseOperation(javax.swing.WindowConstants.EXIT_ON_CLOSE); btnp2.setText("2"); btnp2.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp2MouseClicked(evt); } }); btncon.setText("Conectar"); btncon.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnconMouseClicked(evt); } }); btndesc.setText("Desconectar"); btndesc.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btndescMouseClicked(evt); } }); btnp3.setText("3"); btnp3.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp3MouseClicked(evt); } }); btnp4.setText("4"); btnp4.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp4MouseClicked(evt); } }); btnp5.setText("5"); btnp5.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp5MouseClicked(evt); } }); btnp9.setText("9"); btnp9.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp9MouseClicked(evt); } }); btnp6.setText("6"); btnp6.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp6MouseClicked(evt); } }); btnp7.setText("7"); btnp7.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp7MouseClicked(evt); } }); btnp8.setText("8"); btnp8.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp8MouseClicked(evt); } }); btn13.setText("13"); btn13.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btn13MouseClicked(evt); } }); btnp10.setText("10"); btnp10.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp10MouseClicked(evt); } }); btnp11.setText("11"); btnp11.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp11MouseClicked(evt); } }); btnp12.setText("12"); btnp12.addMouseListener(new java.awt.event.MouseAdapter() { public void mouseClicked(java.awt.event.MouseEvent evt) { btnp12MouseClicked(evt); } }); javax.swing.GroupLayout layout = new javax.swing.GroupLayout(getContentPane()); getContentPane().setLayout(layout); layout.setHorizontalGroup( layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGroup(layout.createSequentialGroup() .addGap(20, 20, 20) .addGroup(layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING, false) .addGroup(layout.createSequentialGroup() .addComponent(btncon) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED, javax.swing.GroupLayout.DEFAULT_SIZE, Short.MAX_VALUE) .addComponent(btndesc)) .addGroup(layout.createSequentialGroup() .addComponent(btnp6, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp7, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp8, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp9, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE)) .addGroup(layout.createSequentialGroup() .addComponent(btnp10, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp11, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp12, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btn13, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE)) .addGroup(layout.createSequentialGroup() .addComponent(btnp2, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp3, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp4, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED) .addComponent(btnp5, javax.swing.GroupLayout.PREFERRED_SIZE, 50, javax.swing.GroupLayout.PREFERRED_SIZE))) .addContainerGap(20, Short.MAX_VALUE)) ); layout.setVerticalGroup( layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addGroup(layout.createSequentialGroup() .addContainerGap() .addGroup(layout.createParallelGroup(javax.swing.GroupLayout.Alignment.BASELINE) .addComponent(btncon) .addComponent(btndesc)) .addPreferredGap(javax.swing.LayoutStyle.ComponentPlacement.RELATED, 20, Short.MAX_VALUE) .addGroup(layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addComponent(btnp2) .addComponent(btnp3) .addComponent(btnp4) .addComponent(btnp5)) .addGap(18, 18, 18) .addGroup(layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addComponent(btnp6) .addComponent(btnp7) .addComponent(btnp8) .addComponent(btnp9)) .addGap(18, 18, 18) .addGroup(layout.createParallelGroup(javax.swing.GroupLayout.Alignment.LEADING) .addComponent(btnp10) .addComponent(btnp11) .addComponent(btnp12) .addComponent(btn13)) .addGap(22, 22, 22)) ); pack(); }// </editor-fold> private void btnp2MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p2"); } private void btnconMouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("connect"); } private void btndescMouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("disconnect"); } private void btnp3MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p3"); } private void btnp4MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p4"); } private void btnp5MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here action("p5"); } private void btnp9MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p9"); } private void btnp6MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p6"); } private void btnp7MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p7"); } private void btnp8MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p8"); } private void btn13MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p13"); } private void btnp10MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p10"); } private void btnp11MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p11"); } private void btnp12MouseClicked(java.awt.event.MouseEvent evt) { // TODO add your handling code here: action("p12"); } /** * @param args the command line arguments */ public static void main(String args[]) throws IOException { /* Set the Nimbus look and feel */ //<editor-fold defaultstate="collapsed" desc=" Look and feel setting code (optional) "> /* If Nimbus (introduced in Java SE 6) is not available, stay with the default look and feel. * For details see http://download.oracle.com/javase/tutorial/uiswing/lookandfeel/plaf.html */ try { for (javax.swing.UIManager.LookAndFeelInfo info : javax.swing.UIManager.getInstalledLookAndFeels()) { if ("Nimbus".equals(info.getName())) { javax.swing.UIManager.setLookAndFeel(info.getClassName()); break; } } } catch (Exception e) { } //</editor-fold> /* Create and display the form */ java.awt.EventQueue.invokeLater(new Runnable() { public void run() { new BDArduino().setVisible(true); } }); //} while (true) { // int sql8 = Integer.parseInt(Sql.getDBinfo("SELECT * FROM arduinoData WHERE id=1", "pin8")); if (connected == true && sql8 != aux_sql8) { aux_sql8 = sql8; if(sql8 == 1){ writeData(2); }else{ writeData(3); } } int sql2 = Integer.parseInt(Sql.getDBinfo("SELECT * FROM arduinoData WHERE id=1", "pin2")); if (connected == true && sql2 != aux_sql2) { aux_sql2 = sql2; if(sql2 == 1){ writeData(4); }else{ writeData(5); } } try { Thread.sleep(500); } catch (InterruptedException e) { e.printStackTrace(); } } } // Variables declaration - do not modify private javax.swing.JButton btn13; private javax.swing.JButton btncon; private javax.swing.JButton btndesc; private javax.swing.JButton btnp10; private javax.swing.JButton btnp11; private javax.swing.JButton btnp12; private javax.swing.JButton btnp2; private javax.swing.JButton btnp3; private javax.swing.JButton btnp4; private javax.swing.JButton btnp5; private javax.swing.JButton btnp6; private javax.swing.JButton btnp7; private javax.swing.JButton btnp8; private javax.swing.JButton btnp9; // End of variables declaration }

    Read the article

< Previous Page | 9 10 11 12 13