Search Results

Search found 2496 results on 100 pages for 'albert green'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 13/100 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

  • Smoothwall Express interface issues

    - by Timbermar
    I have a SmoothWall Express box that is currently configured with a Green and Purple interface. Both interfaces are in the same /24 subnet (which seems odd to me). The green interface (address of .254) has a DHCP server that is pushing addresses from .1 to .100 and the purple interface (.253) is pushing addresses from .101 to .120. Every machine here is trusted, and as such is connected to the green interface via a wired connection or wireless APs. Nothing is connected at all (port is physically empty, traffic graphs show no activity) to the purple interface. However, every machine here is pulling addresses from the purple interface. So the question boils down to, how do I remove/stop my machines from pulling from the purple dhcp interface? Also, shouldn't the purple interface (if we were using it for guest Wifi or something) be on a different subnet (i.e. 192.168.100.0/24 instead of 192.168.1.0/24 with all the trusted machines)?

    Read the article

  • I will need a formula showing counts, totals and sub-totals for data set from different sheet

    - by Sapthagiri
    I am using MS2003 EXCEL. I have a cell in Sheet 1 with a color value and totals, with sub-totals. On sheet 2, I have a data set with 3 columns (colors, dress, type). On Sheet 1, I will need a tabulation showing Totals for Colors, with totals at sub-group of dress (shirt,pants) split by type totals (Full, Half, Tee) Below table represents my Data set in Sheet 2 Colors Make Dress Type -------------------------------- Red Arrow shirt full Red Levi shirt half blue Rugger Pant full yellow Wrangler shirt tee yellow Rugger Pant half yellow Arrow shirt tee yellow Wrangler Pant half Green Rugger Pant full Red Levi shirt tee blue Rugger Pant full blue Arrow shirt full blue Wrangler Pant half Green Levi shirt full I will need a formula showing counts, totals and sub-totals on Sheet 1 for data set from Sheet 2. Refer my table below which represent my expected data on Sheet 1, total Shirt Full Half Tees Pants Full Shorts Red 10 8 4 3 1 2 1 1 Blue Green Yellow Please note I am not looking for a Pivot table solution.

    Read the article

  • Install Windows 7 from ISO image

    - by Albert
    Hi, I have an ISO file of the Windows 7 DVD and I want to install it on my PC which currently only runs Linux. I don't have any DVD drive. I have some unpartitioned space on one disk where I want to install it in. When I am doing this for Linux, I usually just create the partitions from the running system, format them, mount them, copy files over, chroot into it, setup the stuff and I can boot into it (or I use some of the uncountable available scripts which do exactly that automatically). However, I have no idea how to do the same thing with Windows. So far, I tried with VMware, i.e. I gave it direct full access to the disk where I want to install it in, installed it there, then tried to boot natively into it. The Windows logo showed up but after maybe 3 seconds or so, it crashes. Safe mode also crashes. I already expected that this probably would exactly behave the way it does right now because I have heard that Windows is quite sensible about hardware changes (i.e. the VMware hardware and the real hardware). However, how can I fix it now that it works? Or I could also just delete it again and try just over. But how exactly? I also searched for ways to boot directly into an ISO file. There seem to be ways to do that via GRUB (and maybe some additional boot loader), although quite complicated. I already tried one method (GRUB: map ...iso (hdX)), however, that didn't worked. Also, even if it does work, I will get into trouble when I boot into the newly installed Windows and it requests for the DVD (because it does that at the first boot into the new system). Seems all quite complicated. Isn't there some easy way like I would do it for Linux? Or what would be the easiest way to get what I want?

    Read the article

  • What is the method to reset the Planar 1910m monitor?

    - by Richard J Foster
    My monitor (a Planar, apparently model number PL1910M) is not working. (It is flashing a green / orange sequence which I believe to be an error code. The sequence, in case it helps consists of orange and green three times quickly followed by a longer orange, then another green followed by a long period where both colors appear to be present). I vaguely recall a co-worker suffering from a similar problem, and our IT department "resetting" the monitor by holding down a certain set of keys as they apply power. Unfortunately, I do not remember what that key sequence was, our IT department is not responding, and the Planar web site is blocked by the content filtering firewall we have in place! What is the sequence to perform the reset? (For bonus geek-credit, what does the code mean... as if it indicates a blown component clearly a reset will not help me. ;-))

    Read the article

  • Share Firefox/Thnderbird data between W7 and Linux Mint 12 in dual boot computer

    - by Albert
    I've just set up my laptop (where I had running only W7) with a dual boot to run Linux Mint 12 as well. I have a "Data" partition (apart from the required partitions for W7 and Linux) where I store pretty much everything that isn't software installations (music, videos, project files, etc). I seem to be able to access that NTFS partition totally fine from Mint (like I've always done with W7), which is cool because I can access all that stuff regardless of which OS I'm using. I would like to know if it's possible (and how) to go one step further and share programs data between the two OS. One example would be my Firefox and Thunderbird data. For example, in Firefox share my bookmarks (and if I could share history, autocomplete and all that stuff, that would be awesome). In thunderbird, be able to share my mail and configuration, seeing the same inbox, folders, message rules, etc... So if I receive/send an email from W7 and later switch to Mint, I can see that email as it had been received/sent from Mint, and vice versa. Is this even possible? Or am I asking for too much convenience? If it's possible, any clues on how to set it all up?

    Read the article

  • FTP Access Denied when uploading to server

    - by Albert
    Ok, here's the story. I have a server running FTP 'out there' I can connect to it using the admin account, browse files, download files. When I try to upload files, I get 550 Access Denied. I have tried through FileZilla and command line. I have windows firewall turned off (on my machine) I can UPLOAD files from another machine (using the same admin account) on our local network (that means, same public IP) what is the problem? I am running Windows 7, Build 7100 and the other machine on the network is running XP SP3 The thing that gets me though, is that this worked for the last probably 4 months, without a problem, I get back in the office after a weekend today and it won't work...

    Read the article

  • how to convert all to lowercase user names in Active directory

    - by Albert Widjaja
    I am trying to get our subversion configuration management repository to work with active directory. At the moment I am having a problem with some users having mixed case user names in active directory. Would it be possible to change all users with mixed case user names to be all lowercase instead? I'm using Windows Server 2003 Active Directory with 64 bit domain controller running on Windows 2000 mixed functionality.

    Read the article

  • Problem with SVN filename encoding on Mac OS X

    - by Albert
    I have some filename with some Unicode character in it. All filenames on Mac OS X are UTF8 encoded. Also $LANG is set to en_US.UTF-8. However, it seems svn has some problems with that: az@ip212 1054 (Integration) %ls Abbildungen Verbesserungsvorschläge_Applets.odt AllgemeineAnmerkungen.rtf Verbesserungsvorschläge_Applets.rtf Geogebra Vorlagen Texte az@ip212 1055 (Integration) %svn ls Abbildungen/ AllgemeineAnmerkungen.rtf Geogebra/ Texte/ Verbesserungsvorschläge_Applets.rtf Verbesserungsvorschläge_Applets.odt Vorlagen/ az@ip212 1056 (Integration) %svn del Verb*.odt svn: Use --force to override this restriction svn: 'Verbesserungsvorschläge_Applets.odt' is not under version control az@ip212 1057 (Integration) %svn status ? Verbesserungsvorschläge_Applets.odt ! Verbesserungsvorschläge_Applets.odt az@ip212 1058 (Integration) % As you can see, svn del does not recognize the filename. And even svn status gets confused about it. How can I fix this? I also tried with LC_CTYPE=$LANG LC_ALL=$LANG LC=$LANG but no change.

    Read the article

  • How do I turn a shared computer back into a shared media drive?

    - by Brian Green
    There is an external hard drive that is set up as a shared media device for a TV. I tried to hook up my the library on my desktop as a shared media drive to watch movies from my computer on the TV. It worked for a little bit but about 5 seconds after getting into my computer the tv went blank and I couldn't access the external hard drive any more. When I checked on my computer the Hard drive was no longer a shared media device but now it was a computer on the network. How do I fix this and turn it back into a shared media device so I can access it on the TV?

    Read the article

  • memcached install issues with lib event on server

    - by albert N
    I've installed libevent on my server in the directory root/data/ and have i'm about to install memcached with ./configure –with-lib-event=/data/; make; make install However, after running a bit I get this error saying i'm pointing to the wrong directory for libevent. checking for libevent directory... configure: error: libevent is required. You can get it from http://www.monkey.org/~provos/libevent/ If it's already installed, specify its path using --with-libevent=/dir/ make: *** No targets specified and no makefile found. Stop. make: *** No rule to make target `install'. Stop. Any suggestions. I am not experience with cli so anything is help. Thanks!

    Read the article

  • Windows 7 Install: No drives were found

    - by Albert Bori
    I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

    Read the article

  • Setting up virtualbox for outside access

    - by Morgan Green
    I have a computer running a server that my subdomain on my shared hosting account points to. IE subdomain.mydomain.org goes to my home server. Now then; what I'm wanting to do is be able to access my VirtualBox servers through that subdomain and a different port. E.G Ubuntu Virtual Box Server 1 Username:Ubuntuhost1 Password:MyUbuntuHost1 Port:4000 Internal IP: 192.168.1.60 External IP: 24.29.138.45 Ubuntu Virtual Box Server 2 Username:UbuntuHost2 Password:MyUbuntuHost2 Port:4001 Internal IP: 192.168.1.61 External IP: 24.29.138.45 Now I want to be able to access RDP number 1 through Port 4000, but if I access Port 4001 it will connect to the server on port 4001; both using the same subdomain. The next issue is the fact that even though I know what the IP addresses are on the router for the virtualbox hosts through ifconfig it doesn't change the fact that they don't show up on the router. If anyone knows how to configure this to work please help me out because I've been racking my brain to the highest extent I can. Alright; here's an edit to clarify more; Sorry. My ports on the router are edited to forward Port 4000 on Internal IP 192.168.1.63 (My Ubuntu Internal IP address) Now when I go to my Router Home Page my VirtualBox Internal IP Address doesn't show on the attached device listings, so I set up port forwarding anyways to the VirtualBox Internal IP. My end goal is when I connect to mydomain.org and I connect through port 3389 it takes me to my host computers server, but if I put in mydomain.org and go through port 4000 it's going to redirect to my VirtualBox server; Is this even possible? Sorry; I'm trying to clarify the most I think I can I just don't know how else to explain my issue.

    Read the article

  • setup PXE (i.e. DHCP + TFTP) server on MacOSX

    - by Albert
    What is the easiest way to setup an PXE server (i.e. a DHCP server + TFTP server) on MacOSX? Is there maybe some easy-to-use tool which just comes with both servers builtin? I have done that in the past but I remember that it took me several hours of editing some config files of tftpd (I think) and different versions of dhcpd, many trials and errors until I got it working (mostly). Now I have a fresh MacOSX installation and I want to avoid any complicated setup.

    Read the article

  • how to create stub DNS zone for emulating my customer production environment ?

    - by Albert Widjaja
    Hi All, Is it possible to emulate my customer production environment inside my AD domain by just creating the same domain inside my primary DNS server ? Can I created mycustomer.com DNS zone (STUB) just for the sake of listing few database servers and application servers and then for the other DNS records eg. MX, NS and the other refer to the REAL MX record entry so that my Exchange Server email flow is unaffected to mycustomer.com ? because if I just create A record in my current domain for some of the servers, the FQDN is not exactly what I want. Thanks.

    Read the article

  • What is the method to reset the Planar 1910m monitor?

    - by Richard J Foster
    My monitor (a Planar, apparently model number PL1910M) is not working. (It is flashing a green / orange sequence which I believe to be an error code. The sequence, in case it helps consists of orange and green three times quickly followed by a longer orange, then another green followed by a long period where both colors appear to be present). I vaguely recall a co-worker suffering from a similar problem, and our IT department "resetting" the monitor by holding down a certain set of keys as they apply power. Unfortunately, I do not remember what that key sequence was, our IT department is not responding, and the Planar web site is blocked by the content filtering firewall we have in place! What is the sequence to perform the reset? (For bonus geek-credit, what does the code mean... as if it indicates a blown component clearly a reset will not help me. ;-))

    Read the article

  • How to install PyQt on Mac OS X 10.6

    - by Albert
    I want to install PyQt. This seems kind of complicated to install on OS X. I haven't found any precompiled packages of it (are there any? I would really prefer those). So I downloaded PyQt. And SIP, because it depends on that. These files: http://www.riverbankcomputing.co.uk/static/Downloads/PyQt4/PyQt-mac-gpl-4.7.3.tar.gz http://www.riverbankcomputing.co.uk/static/Downloads/sip4/sip-4.10.2.tar.gz Did a python configure.py && make && sudo make install on SIP -- installed without any problems. Tried the same on PyQt -- and failed of course: /Library/Frameworks/QtCore.framework/Headers/qglobal.h:288:2: error: #error "You are building a 64-bit application, but using a 32-bit version of Qt. Check your build configuration." Ok, so I tried with python configure.py --use-arch=i386. Same error. Any idea?

    Read the article

  • Apache vhosts config: Host Name instead of IP Address

    - by Johe Green
    I have a domain (example.com) hosted at an external provider. I directed the subdomain sub.example.com to my ubuntu server (12.04 with apache2). On my ubuntu server I have a vhost setup like this. The rest of the config is basically apache 2 standard: <VirtualHost *:80> ServerName sub.example.com ServerAlias sub.example.com ServerAdmin [email protected] DocumentRoot /var/www/sub.example.com ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined WSGIScriptAlias / /home/application/sub.example.com/wsgi.py <Directory /home/application/sub.example.com> <Files wsgi.py> Order allow,deny Allow from all </Files> </Directory> </VirtualHost> When I enter http://sub.example.com in my browser my application shows up fine. But the domain is replaced by the IP address of my server. Do I have to configure my server somewhere else to deliver all its content under my domain sub.example.com?

    Read the article

  • I want to replace a number with successive numbers, starting at 1 and going up.

    - by Pär-Magnus Green
    I'm aware that this is something people can easily program, but I'm not familiar with those things, so I was hoping there was an easier solution. I've edited a large database of questions, including sorting, and ended up getting all the question ID's mixed up. I'm trying to do this in Notepad++, but any other suggestions are welcome. I'm wondering if there's a way to search for a string (ex. "Question[any number]") and replace the numbers with first 1, then 2, et.c. For clarification, this is how one question looks like: TriviaBot_Questions[3]['Question'][63] = "Acronyms: What does WTT stand for?"; TriviaBot_Questions[3]['Answers'][63] = {"Want To Trade"}; TriviaBot_Questions[3]['Category'][63] = 7; TriviaBot_Questions[3]['Points'][63] = 1; TriviaBot_Questions[3]['Hints'][63] = {}; and the next question, as is now, is not followed by 64. It might be 245 or 1029, and regardless of which number it is, I want it replaced with "previous number + 1", basically.

    Read the article

  • Sharepoint .PDF contents displaying as 'searchtext.xml' in searches

    - by Green Muffins
    Hi Experts, I recently used installed ifilter in my sharepoint farm to enable searching of the contents of .pdf documents. All went well, except if I search for contents of any .pdf file, they appear in the search results with document title "searchtext.xml", and the link to the document gives a giant page of the .pdf contents in an .xml looking browser page. :s I have added .pdf filetypes to the search, so I am unsure why it is reading them incorrectly.. if I search for a .pdf document title such as 'document.pdf' it will display the result as a html page, though the link does follow to a readable .pdf file. Any help?

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >