Search Results

Search found 10893 results on 436 pages for 'failed'.

Page 13/436 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

  • iptables-restore: line 1 failed

    - by Doug
    Hello, I am new to servers, and I was following this guide and it failed on the first command instructed. Could anyone give me a hand? http://wiki.debian.org/iptables ~ZORO~:/etc# iptables-restore < /etc/iptables.test.rules iptables-restore: line 1 failed Edit: iptables.test.rules ~ZORO~:/etc# cat /etc/iptables.test.rules *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You could modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections for script kiddies # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Now you should read up on iptables rules and consider whether ssh access # for everyone is really desired. Most likely you will only allow access from certain IPs. # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls (access via 'dmesg' command) -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy: -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

    Read the article

  • unable to recover data from failed hdd

    - by Eslam Elyamany
    my hdd failing (or maybe totally dead) i've connected the hdd via USB but it doesn't appear in fdisk Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xe9fb38fb Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 40959999 20376576 7 HPFS/NTFS/exFAT /dev/sda4 40962046 976771071 467904513 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 82913280 86910975 1998848 82 Linux swap / Solaris /dev/sda6 86913024 394113023 153600000 7 HPFS/NTFS/exFAT /dev/sda7 40962048 82913279 20975616 83 Linux /dev/sda8 394122708 976768064 291322678+ 7 HPFS/NTFS/exFAT Partition 8 does not start on physical sector boundary. no sdc appears here , BUT it's appears on /dev/ rootghost-lap:/home/ghost# ls /dev/sd* /dev/sda /dev/sda2 /dev/sda5 /dev/sda8 /dev/sdb /dev/sdc1 /dev/sdc2 /dev/sdc6 /dev/sdc8 /dev/sda1 /dev/sda4 /dev/sda6 /dev/sda9 /dev/sdc /dev/sdc10 /dev/sdc5 /dev/sdc7 /dev/sdc9 also it appears in proc Code: rootghost-lap:/home/ghost# cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 102400 sda1 8 2 20376576 sda2 8 4 1 sda4 8 5 1998848 sda5 8 6 153600000 sda6 8 8 291322678 sda8 8 9 20975616 sda9 11 0 1048575 sr0 11 1 99136 sr1 8 32 244198583 sdc 8 33 14651248 sdc1 8 34 1 sdc2 8 37 15380480 sdc5 8 38 4153344 sdc6 8 39 48829536 sdc7 8 40 48829536 sdc8 8 41 110374551 sdc9 8 42 1975963 sdc10 and dmesg : [10604.777168] end_request: I/O error, dev sdc, sector 1 [10604.817238] sd 26:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10604.817243] sd 26:0:0:0: [sdc] Sense Key : Aborted Command [current] [10604.817248] sd 26:0:0:0: [sdc] Add. Sense: No additional sense information [10604.817253] sd 26:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 02 00 00 06 00 ok now , let's see what i've tried testdisk to check for partitions -- failed dd to copy data from /dev/sdcX -- provide strange output size for example /dev/sdc1 is about 15G , the output for dd is 62G+ so i had to cancle it safecopy successfully made an image for partitons , but can't fix images, can't mount it, can't do any thing with it and some other tools i've tried and all failed , so any idea ?

    Read the article

  • Login failed for user 'XXX' on the mirrored sql server

    - by hp17
    Hello, We have 4 web servers that host our asp.net (3.5) application. Randomly, we get error messages like : 1) "Login failed for user 'userid'" 2) "A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server)" we are running sql2005 and have a principle and a mirror db (sync). When these exceptions are thrown, I look at the SQL error logs on the mirrored db and noticed the failed login messages in there. The principle db is running fine and the other web apps are working great. this will happen for maybe 10 min, then the app pool recycles and it starts hitting the principle db again. Is there a configuration I have incorrect? my theory is that our principle db is forwarding the request to the mirror, but that should never happen. any help??

    Read the article

  • SQL Server 2008 login problem with ASP.NET application: Failed to open the explicitly specified database

    - by eulerfx
    I am running SQL Server 2008 Express Edition on Windows Server 2008 with an ASP.NET application which must access the server. The ASP.NET application is associated with an application pool that runs on the NetworkService account. This account in turn has a Login and User record on SQL Server in the required database. When I attempt to run the ASP.NET website I get a blank page and when viewed in the error log, I seem to be getting this information event record: Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. Reason: Failed to open the explicitly specified database. [CLIENT: myLocalMachine] The connection string has Trusted_Connection=True; and the required database specified. When I explicitly specify the user name and password I get another login error stating the password is incorrect, even though the same un/pw combination works through SQL Server Management studio. The NETWORK SERVICE account seems to have all the required privileges for the database. Also, I made a test ASP.NET website project which does a simple select from a table in that database, and using the same config file I am not getting the error and it seems to work. Is it something to do with trust levels then, because the original ASP.NET web app references various DLLs including open source libraries. Also, the application does not seem to be able to write to the event log itself, throwing a security exception, even though everything in the config files, including machine.config states the app is in full trust.

    Read the article

  • Failed none and iptables

    - by Michael
    The problem is that when I ssh to my host with putty and enter user name, after that the password prompt delays. Found this is directly related to my iptables and can solve by changing default policy to ACCEPT. If default INPUT policy is ACCEPT, then password prompt is coming immediately. Mar 13 00:05:01 server-ubuntu sshd[6154]: Connection from 192.168.0.10 port 26304 Mar 13 00:05:06 server-ubuntu sshd[6154]: Failed none for acid from 192.168.0.10 port 26304 ssh2 However, if default INPUT policy is DROP, I got slight delay in getting password prompt after I enter username Mar 13 00:07:12 server-ubuntu sshd[6177]: Connection from 192.168.0.10 port 26333 Mar 13 00:07:35 server-ubuntu sshd[6177]: Failed none for acid from 192.168.0.10 port 26333 ssh2 For the second case, I tried to set default policy for FORWARD and OUTPUT chains to ACCEPT, but it didn't help. The only rule in this case is: -A INPUT -i eth1 -m mac --mac-source 00:26:XX:XX:XX:XX -j ACCEPT 00:26:XX:XX:XX:XX is the mac address from which I am trying to ssh to server's LAN(eth1). I'm sure there has to be some rule, which I can use while default INPUT chain policy is DENY in order to get password prompt immediately. I realize that the error message in the log is something normal and part of some verification procedure.

    Read the article

  • p410i Mirror failed couldnt find same disk

    - by Heishiro Mitsurugi
    I have an HP server with an P410i RAID Card installed. I had two SATA Drives connected (250GB each). The RAID was configured as a Mirror. A few days ago the drive one (1) failed, and i had to remove it. Tried to find the same part number here in Venezuela, but i couldn't. So, i bought a 500GB SATA Drive, and connected it to the same bay where the 250GB failed drive was. When the server booted, it asked me if i wanted to rebuild the data. I selected the option for that, and Windows Server restarted properly. When i got into the ACU (Array Configuration Utility) it told me that it was rebuilding the data. Today the warning went away, and according to the ACU everything is just fine. My question is... What i did was right? Can i create a mirror from a 250GB disk in a 500GB disk using the p410i? I have done that before, but only using software RAID in Windows, and it just uses the space it needs. As a matter of fact, when did that using Windows i was able to use the remaining space in the bigger drive, but in the p410i i can't use it. Should i be worried? Thanks a lot in advance for any pointers or info that you could give on this. Heishiro

    Read the article

  • nvidia driver problems after upgrading to 3.2.0-26 on Ubuntu 12.04 64bit

    - by Lev Levitsky
    After installing latest updates I can't set screen resolution higher than 1024x768; every time after the boot I get a message Could not apply the stored configuration for the monitors (Note: removing ~/.config/monitors.xml stopped the message, but not the problem) I can boot with 3.2.0-25 and the graphics look normal. Here's what I have in /var/log/apt/term.log (excerpt): Setting up linux-image-3.2.0-26-generic (3.2.0-26.41) ... Running depmod. update-initramfs: deferring update (hook will be called later) Examining /etc/kernel/postinst.d. run-parts: executing /etc/kernel/postinst.d/dkms 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic Error! Problems with depmod detected. Automatically uninstalling this module. DKMS: Install Failed (depmod problems). Module rolled back to built state. run-parts: executing /etc/kernel/postinst.d/initramfs-tools 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic update-initramfs: Generating /boot/initrd.img-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/pm-utils 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/update-notifier 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic run-parts: executing /etc/kernel/postinst.d/zz-update-grub 3.2.0-26-generic /boot/vmlinuz-3.2.0-26-generic Generating grub.cfg ... Found linux image: /boot/vmlinuz-3.2.0-26-generic Found initrd image: /boot/initrd.img-3.2.0-26-generic Found linux image: /boot/vmlinuz-3.2.0-25-generic Found initrd image: /boot/initrd.img-3.2.0-25-generic Found linux image: /boot/vmlinuz-3.2.0-24-generic Found initrd image: /boot/initrd.img-3.2.0-24-generic Found linux image: /boot/vmlinuz-3.2.0-23-generic Found initrd image: /boot/initrd.img-3.2.0-23-generic Found linux image: /boot/vmlinuz-3.0.0-17-generic Found initrd image: /boot/initrd.img-3.0.0-17-generic Found memtest86+ image: /boot/memtest86+.bin I went to "additional drivers" and saw some updates available there, but an attempt to install them failed, leaving the following in /var/log/jockey.log (long log, pasted here). The full log won't fit in the question, so I'm showing $ fgrep 'ERROR' /var/log/jockey.log 2012-06-30 17:29:57,897 WARNING: modinfo for module vmxnet failed: ERROR: modinfo: could not find module vmxnet 2012-06-30 17:29:57,937 WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl 2012-06-30 17:29:58,072 WARNING: modinfo for module nvidia_96 failed: ERROR: modinfo: could not find module nvidia_96 2012-06-30 17:29:58,240 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-06-30 17:29:58,293 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-06-30 17:29:58,351 WARNING: modinfo for module nvidia_173_updates failed: ERROR: modinfo: could not find module nvidia_173_updates 2012-06-30 17:29:58,385 WARNING: modinfo for module nvidia_173 failed: ERROR: modinfo: could not find module nvidia_173 2012-06-30 17:29:58,420 WARNING: modinfo for module nvidia_96_updates failed: ERROR: modinfo: could not find module nvidia_96_updates 2012-06-30 17:29:58,455 WARNING: modinfo for module ath_pci failed: ERROR: modinfo: could not find module ath_pci 2012-06-30 17:29:58,478 WARNING: modinfo for module fglrx_updates failed: ERROR: modinfo: could not find module fglrx_updates 2012-06-30 17:29:58,531 WARNING: modinfo for module fglrx failed: ERROR: modinfo: could not find module fglrx 2012-06-30 17:29:58,588 WARNING: modinfo for module omapdrm_pvr failed: ERROR: modinfo: could not find module omapdrm_pvr 2012-06-30 17:29:59,537 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-06-30 17:29:59,613 WARNING: modinfo for module nvidia_173_updates failed: ERROR: modinfo: could not find module nvidia_173_updates 2012-06-30 17:29:59,686 WARNING: modinfo for module nvidia_173 failed: ERROR: modinfo: could not find module nvidia_173 2012-06-30 17:29:59,764 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-06-30 17:30:29,544 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-06-30 17:30:29,545 ERROR: XorgDriverHandler.enable(): package or module not installed, aborting I'm not sure if it's a bug, as the first log shows some errors. What can I try?

    Read the article

  • How to fix boot and mount failed drops to initramfs prompt in Ubuntu 12.04?

    - by msPeachy
    Ubuntu partition does not boot. This started after a power interruption during system boot. The next time I boot, I encountered the following error message: mount: mounting /dev/disk/by-uuid/3f7f5cd9d-6ea3-4da7-b5ec-**** on /root failed: Invalid argument mount: mounting /sys on /root/sys failed: No such file or directory mount: mounting /dev on /root/dev failed: No such file or directory mount: mounting /sys on /root/sys failed: No such file or directory mount: mounting /proc on /root/proc failed: No such file or directory Target file system doesn't have /sbin/init. No init found. Try passing init= bootarg. Busybox v1.18.5 (Ubuntu 1:1.18.5-1ubuntu4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) _ I've searched for similar posts here and most of the recommended solution is to reboot to the Ubuntu LiveCD. That's another problem because I cannot boot to a LIVEUSB, this is the error message I get when booting to a LiveUSB: Busybox v1.18.5 (Ubuntu 1:1.18.5-1ubuntu4) built-in shell (ash) Enter 'help' for a list of built-in commands. (initramfs) mount: mounting /dev/sda2 on /isodevice failed: Invalid argument Could not find the ISO /ubuntu-12.04-desktop-i386.iso. This could also happen if the file system is not clean because of an operating system crash, an interrupted boot process, an improper shutdown, or unplugging of a removable device without first unmounting or ejecting it. To fix this, simply reboot into Windows, let it fully start, log in, run 'chkdsk /r', then gracefully shut down and reboot back into Windows. After this you should be able to reboot again and resume the installation. I cannot boot into Windows because I don't have a Windows partition. Do I have to install Windows to fix this problem? Is there a way to fix this in the (initramfs) prompt? Please help. Thank you!

    Read the article

  • Padding is invalid and cannot be removed

    - by Ajay
    I have hosted an asp.net 2.0 site. Everyday, i am getting an error "Padding is invalid and cannot be removed" 2-3 times. Backend used is sql server 2005. the site is controlled via plesk 9.2 CP. Pooling is enabled with timeout as 120 Minutes, in IIS. Can it be the reason for this? I have not used any encryption except for the stored passwords(MD5) The error message is : " Base Exception = : Padding is invalid and cannot be removed. - Source : System.Web - TargetSite :Void ThrowError(System.Exception, System.String, System.String, Boolean)Message : Validation of viewstate MAC failed. If this application is hosted by a Web Farm or cluster, ensure that configuration specifies the same validationKey and validation algorithm. AutoGenerate cannot be used in a cluster. " & System Log (Application) says " Event code: 4009 Event message: Viewstate verification failed. Reason: The viewstate supplied failed integrity check. Event detail code: 50203 ViewStateException information: Exception message: Invalid viewstate. Port: 31235 User-Agent: Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1) " I have hosted it in a dedicated server and not in a web farm. Will keeping a static machine key help resolve this issue? Please guide me on this.

    Read the article

  • Login failed for user 'DOMAIN\MACHINENAME$'

    - by sah302
    I know this is almost duplicate of : http://stackoverflow.com/questions/1269706/the-error-login-failed-for-user-nt-authority-iusr-in-asp-net-and-sql-server-2 and http://stackoverflow.com/questions/97594/login-failed-for-user-username-system-data-sqlclient-sqlexception-with-linq-i but some things don't add up compared to other appliations on my server and I am not sure why. Boxes being used: Web Box SQL Box SQL Test Box My Application: I've got aASP.NET Web Application, which references a class library that uses LINQ-to-SQL. Connection string set up properly in the class library. As per http://stackoverflow.com/questions/97594/login-failed-for-user-username-system-data-sqlclient-sqlexception-with-linq-i I also added this connection string to the Web Application. The connection string uses SQL credentials as so (in both web app and class library): <add name="Namespace.My.MySettings.ConnectionStringProduction" connectionString="Data Source=(SQL Test Box);Initial Catalog=(db name);Persist Security Info=True;User ID=ID;Password=Password" providerName="System.Data.SqlClient" /> This connection confirmed as working via adding it to server explorer. This is the connection string my .dbml file is using. The problem: I get the following error: System.Data.SqlClient.SqlException: Login failed for user 'DOMAIN\MACHINENAME$'. Now referencing this http://stackoverflow.com/questions/1269706/the-error-login-failed-for-user-nt-authority-iusr-in-asp-net-and-sql-server-2 it says that's really the local network service and using any other non-domain name will not work. But I am confused because I've checked both SQL Box and SQL Test Box SQL Management Studio and both have NT AUTHORITY/NETWORK SERVICE under Security - Logins, at the database level, that isn't listed under Security - Users, but at the database level Security - Users I have the user displayed in the connection string. At NTFS level on web server, the permissions have NETWORK SERVICE has full control. The reason why I am confused is because I have many other web applications on my Web Server, that reference databases on both SQL Box and SQL Test Box, and they all work. But I cannot find a difference between them and my current application, other than I am using a class library. Will that matter? Checking NTFS permissions, setup of Security Logins at the server and databases levels, connection string and method of connecting (SQL Server credentials), and IIS application pool and other folder options, are all the same. Why do these applications work without adding the machinename$ to the permissions of either of my SQL boxes? But that is what the one link is telling me to do to fix this problem.

    Read the article

  • Outlook add email account: requested operation failed

    - by nute
    I am using MS Outlook 2007, under Windows 7. I am trying to add a new email account. I go through the process, I check "manually configure ...". I enter all the info (it's an IMAP). The "test account settings" says it's all good. I click NEXT and ... THE REQUESTED OPERATION FAILED No explanation, nothing else.

    Read the article

  • Failed Conversion with VMConverter 4.0.1

    - by montespcs
    Received this error @ 57% on Windows Vista Enterprise SP1 conversion going to a VMWorkstation 6.5 image via network share. FAILED: A general system error occurred: SQL_CANTOPEN: unable to open database file Running installed VMConverter 4.0.1-Build161434. Anyone seen this error yet?

    Read the article

  • opendkim reporting read private key failed: no start line

    - by Bob
    I've set up keys with the following: opendkim-genkey -t -s mail -d test.com The private key (pertinent to this question) contains: -----BEGIN RSA PRIVATE KEY----- (some stuff here) -----END RSA PRIVATE KEY----- My opendkim.conf contains: Domain test.com KeyFile /etc/opendkim/dkim.private Selector mail I am then testing with: opendkim-testkey -d test.com -s mail -k /etc/mail/dkim.public Yet receive the following error: opendkim-testkey: PEM_read_bio_PrivateKey() failed error:0906D06C:PEM routines:PEM_read_bio:no start line The files exist and have opendkim as the user and group, and adequate permissions. Has anyone any advice?

    Read the article

  • SSL handshake failed SVN Checkout

    - by Webnet
    I'm using https://IP:PORT/svn/web/repository to checkout remotely from our network here at the office and I'm getting the error... SSL handshake failed: SSL error: unknown protocol My concern is that I've verified that SSL is running and listening on the port I'm specifying. Now.... the port I've specified is forwarded through the office router to the SVN server. Any ideas on what could be going wrong?

    Read the article

  • Installing gitweb failed: No package gitweb available

    - by logii
    I have tried installing gitweb via ssh and failed. Below is what I get. root@server [~]# yum install gitweb Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * rpmforge: ftp-stud.fht-esslingen.de rpmforge | 1.1 kB 00:00 rpmforge/primary | 3.8 MB 00:19 rpmforge 10502/10502 Excluding Packages in global exclude list Finished Setting up Install Process No package gitweb available. Nothing to do Anyone has any idea of what else is missing?

    Read the article

  • "Attach to native process failed" with Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit

    - by Richard
    In trying to install Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit, the dialogue appears as follows. # export JAVAHOME=/usr/java/jdk1.6.0_24/; echo $JAVAHOME /usr/java/jdk1.6.0_24/ # ./setup Launching installer... Attach to native process failed On the server we have the following JREs and I've tried both. $ sudo rpm -qa | egrep "(openjdk|icedtea)" java-1.6.0-openjdk-1.6.0.0-1.27.1.10.8.el5_8 And SElinux appears to be off: # cat /etc/sysconfig/selinux SELINUX=disabled SELINUXTYPE=targeted

    Read the article

  • SSL handshake failed

    - by Webnet
    I'm using https://IP:PORT/svn/web/repository to checkout remotely from our network here at the office and I'm getting the error... SSL handshake failed: SSL error: unknown protocol My concern is that I've verified that SSL is running and listening on the port I'm specifying. Now.... the port I've specified is forwarded through the office router to the SVN server. Any ideas on what could be going wrong?

    Read the article

  • Failed to start X server. REDHAT LINUX 5.3

    - by chankey007
    I installed Red-hat 5.3 problem is that it is not showing graphical interface. only kernel / command prompt is available. I tried startx, then I got this msg No video BIOS modes for chosen depth also showing that ERROR: Failed to start X server. What should I do?

    Read the article

  • Windows 7 update failed (language pack update)

    - by yihang
    I am using Windows 7 Ultimate and tried to install the language pack for chinese simplified from Windows Update and failed for many times. The error code was 8007065B: Windows Update encountered an unknown error. What does the code means? I have tried to google it but cannot find anything. What should I do to solve this problem.

    Read the article

  • Eclipse PDT - Failed to load JavaHL Library.

    - by alexus
    all of the sudden, when I work in my Eclipse PDT I get this error msg, not sure where they came from nor how to get rid of them Failed to load JavaHL Library. These are the errors that were encountered: no libsvnjavahl-1 in java.library.path no svnjavahl-1 in java.library.path no svnjavahl in java.library.path java.library.path = .:/Library/Java/Extensions:/System/Library/Java/Extensions:/usr/lib/java any ideas?

    Read the article

  • Pecl install failed

    - by poru
    Hello, I'm trying to install memcached with pecl but I get every time this error: checking for libmemcached location... configure: error: memcached support requires libmemcached. Use --with-libmemcached-dir= to specify the prefix where libmemcached headers and library are located ERROR: `/tmp/pear/cache/memcached-1.0.1/configure' failed But if I type whereis memcached I get: /usr/bin/memcached /etc/memcached.conf /usr/share/memcached /usr/share/man/man1/memcached.1.gz I'm using a Ubuntu 8.04 server

    Read the article

  • Excel VBA (2007) Subtotal method of Range class failed

    - by robihot
    Hi, I'm getting a Subtotal method of Range class failed Error when i try to run a macro. Code works GREAT (no errors) when i run it using Excel 2003. Here's a snippet... 'SubTotal Sheet Range("A1").Select Selection.Subtotal GroupBy:=1, Function:=xlSum, TotalList:=Array(3, 4, 5, 6, 7, _ 8, 9), Replace:=True, PageBreaks:=False, SummaryBelowData:=True Any help would be appreciated !!!

    Read the article

  • DPM 2010 "Disk failed or disk not found"

    - by SysAdmin
    I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

    Read the article

  • why i failed to build vsftp?

    - by hugemeow
    make, then failed with the following message. the main point is /lib/libcap.so.1: could not read symbols: File in wrong format, confusing... gcc -c readwrite.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c opts.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c ssl.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c sslslave.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c ptracesandbox.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c ftppolicy.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c sysutil.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -c sysdeputil.c -O2 -Wall -W -Wshadow -idirafter dummyinc gcc -o vsftpd main.o utility.o prelogin.o ftpcmdio.o postlogin.o privsock.o tunables.o ftpdataio.o secbuf.o ls.o postprivparent.o logging.o str.o netstr.o sysstr.o strlist.o banner.o filestr.o parseconf.o secutil.o ascii.o oneprocess.o twoprocess.o privops.o standalone.o hash.o tcpwrap.o ipaddrparse.o access.o features.o readwrite.o opts.o ssl.o sslslave.o ptracesandbox.o ftppolicy.o sysutil.o sysdeputil.o -Wl,-s `./vsf_findlibs.sh` /lib/libcap.so.1: could not read symbols: File in wrong format collect2: ld returned 1 exit status make: *** [vsftpd] Error 1 [mirror@hugemeow vsftpd]$ ls /lib/libc libc-2.5.so libcap.so.1.10 libcidn.so.1 libcom_err.so.2.1 libcrypto.so.0.9.8e libcrypt.so.1 libcap.so.1 libcidn-2.5.so libcom_err.so.2 libcrypt-2.5.so libcrypto.so.6 libc.so.6 [mirror@hugemeow vsftpd]$ ls /lib/libc libc-2.5.so libcap.so.1.10 libcidn.so.1 libcom_err.so.2.1 libcrypto.so.0.9.8e libcrypt.so.1 libcap.so.1 libcidn-2.5.so libcom_err.so.2 libcrypt-2.5.so libcrypto.so.6 libc.so.6 [mirror@hugemeow vsftpd]$ ls /lib/libcap.so.1 -l lrwxrwxrwx 1 root root 14 Mar 20 2012 /lib/libcap.so.1 -> libcap.so.1.10 [mirror@hugemeow vsftpd]$ ls /lib/libcap.so.1 -lh lrwxrwxrwx 1 root root 14 Mar 20 2012 /lib/libcap.so.1 -> libcap.so.1.10 [mirror@hugemeow vsftpd]$ ls /lib/libcap.so.1 -lhL -rwxr-xr-x 1 root root 12K Mar 15 2007 /lib/libcap.so.1 this may have something to do with 64 bit system, but i have make modification to vsf_findlibs.sh 48 # Look for libcap (capabilities) 49 if locate_library /lib64/libcap.so.1; then 50 echo "/lib/libcap.so.1"; 51 elif locate_library /lib64/libcap.so.2; then 52 echo "/lib/libcap.so.2"; 53 else 54 # locate_library /usr/lib/libcap.so && echo "-lcap"; 55 # locate_library /lib/libcap.so && echo "-lcap"; 56 locate_library /lib64/libcap.so.1 && echo "-lcap"; 57 fi but make failed with the same error, why?

    Read the article

  • Installing Framework 4.0 Failed

    - by user1565210
    I am trying to install Framework 4.0 on a Windows server 2003 SP2 needed for My ASP.NET application, but it fails during installation! Current framework is version 2.0. Below is a piece of the logfile: [8/2/2012, 13:37:21]Wait for Item (RGB9RAST_x86.msi) to be available [8/2/2012, 13:39:9]Final Result: Installation failed with error code: (0x80070005), "Access is denied. " (Elapsed time: 0 00:01:59). [8/2/2012, 13:39:31]WM_ACTIVATEAPP: Focus stealer's windows WAS visible, NOT taking back focus

    Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >