Search Results

Search found 451 results on 19 pages for 'fallback'.

Page 13/19 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

  • Ping with explicit next-hop selection (aka Monitoring multiple default gateways)

    - by Michuelnik
    I have a linux (debian) router with two internet connections (A) and (B). (A) is preferred, (B) is fallback. I want to monitor the internet connection (and not only the availability of the gateways!) and change the default route appropriately. If (A) is not providing internet, switch to (B) If (A) is providing internet again, switch back to (A). Only problem I have is in case (2). My routing table points towards a working internet so I cannot easily detect whether internet is working over link (A) again. I am search for a ping or traceroute (or other diagnosis-tool) which can select the next-hop explicitly. ping -r looks promising, but can only ping a host on the lan. (It only has to write another destination address in the packet, damnit!) traceroute -g gateway looks even more promising and nearly does what I want - but sets source routing options which my next-hops deny. (Not within my administrative boundary...) I just want a $ping, that can: select a source interface (and address) select a next-hop on that interface ping any arbitrary ip address I could do evil trickery with policy-based routing but that would have production impact for all users. I would like to see a side-effect-free solution....

    Read the article

  • Multiple Routers, Failover, DHCP and multiple gateways. NOT WAN-failover

    - by u_b
    I've had a look around google and this forum but could not find an answer to my question. So probably one of you can help me a little. My intended setup is: Router R1: wan connection to isp. connected backup server. provides some wireless SSID. other connected devices like printer, laptop, etc. both wired and wireless. Router R2: no wan connection to isp but connected to R2. connects mp3-streamer and music server. also serves as a wireless access point with same SSID. other than described connections only wireless connections. I would like to be able to control music even if R1 is off, e.g. with no internet connection. On the other hand I would like to access internet also in the case that R2 is off, i.e. no music access. Last but not least I would like to stream internet radio, i.e., R1 and R2 are on, and music is streamed from internet to R1 to R2 to streamer. I would like to realize all this using DHCP (also using static assignments) so i do not have to configure statically on android, laptop, etc. So my questions are: Can I make DHCP provide a list of two default gateways R1,R2? In order to make clients fallback to other gateway if currently assigned gateway is turned off? Thanks in advance, u_b

    Read the article

  • Router as primary DNS server, Server as alternate? (or vice versa)

    - by Jakobud
    We have a very small business network, with a typical cable modem hooked into a DD-WRT router. We also run a basic CentOS server that does a variety of things, including acting as the primary DNS server for the office. The reason we need an internal DNS server is because we do a lot of internal web development and use the DNS server to add/remove various local network URLs for internal website testing (like www.testsite.com.local). It's very important for us to be able to add/remove URL aliases easily to the DNS. The problem with this setup is that if we ever need to restart the CentOS server or take it offline for upgrades or whatever, then internet access for all computers on the network is lost. That's because each computer relies on that DNS server to access the Internet I guess? The router is online all the time and very very rarely has to be restarted. It would be nice if we could setup my router to be the primary DNS server but still be running DNS on my server. So we could still add my local testing website URLs to the DNS server in CentOS, but be able to also take down the CentOS server without loosing Internet access on the network. How would this be setup? Would I simply need to add both router + server IP addresses to each computer's IP settings? Is the router primary DNS and server secondary DNS server? Or vice versa? Or can one of the two serve as a fallback for the other? What (if anything) needs to be configured on both the router and server in order for them to recognize that the other DNS server exists on the network? Does anyone have any newb-friendly resources for setting up something like this?

    Read the article

  • locale: What is the LANGUAGE variable used for? (and when?)

    - by seya
    I am trying to understand the locales used in Linux. On my Ubuntu 11.10 system locale puts out the following: LANG=en_DK.UTF-8 LANGUAGE=en_GB:en LC_CTYPE=en_GB.UTF-8 LC_NUMERIC="en_DK.UTF-8" LC_TIME="en_DK.UTF-8" LC_COLLATE=en_GB.UTF-8 LC_MONETARY="en_DK.UTF-8" LC_MESSAGES=en_GB.UTF-8 LC_PAPER="en_DK.UTF-8" LC_NAME="en_DK.UTF-8" LC_ADDRESS="en_DK.UTF-8" LC_TELEPHONE="en_DK.UTF-8" LC_MEASUREMENT="en_DK.UTF-8" LC_IDENTIFICATION="en_DK.UTF-8" LC_ALL= (en_dk is for using international day format, continental European number formatting (1.234,56) etc.) I think I understand what the LC_* family does, that LANG is the fallback if one of them is not set and that LC_ALL sets all of the LC_* variables to its value. What I don't know yet, is what LANGUAGE is used for. The notation en_GB:en reminds me of the Accept-Language HTTP header. With the settings above it would mean, British English is used, if a translation for it exists. Otherwise any existing English translation (en_US, en_AU, ..., whatever) would be used. Am I right so far? Also what programs actually obey the LANGUAGE setting? In how far is it different from LC_MESSAGES? Unfortunately, man locale only documents the LC_* family. And searching the web for 'linux locale LANGUAGE' or similar is a mute point. (Of course language is a word often used when talking about locales, and it may also be shown just in the output of locale without being discussed). Does anybody of you can help me out there?

    Read the article

  • Windows 7, Black screen with cursor, impossible to logon

    - by PJC
    First - I have gone through as many possible solutions I've found here and elsewhere. [Edit - to describe the issue in more detail, the PC appears to boot correctly, but instead of the logon screen, I have been getting a black screen WITH the pointer cursor, and it responds correctly to the mouse. Pressing CTL-ALT-DEL brings up the logon screen's background, but with no logon area nor any other content. This screen was at the full resolution before I uninstalled the graphics driver in safe-mode.] I also just ran a full up-to-date AVG scan from boot media. [Edit - the AVG scan, which was updated to today's virus signatures, found no issues at all.] So - steps I've tried: Safe Boot, Restore from before the issue - done, no help. Uninstall the graphics driver - done, now i have a 1024x768 fallback screen, still no way in. sfc /scannow - only doable from Safe boot obviously, but no change. [Edit - booting from restore media, performing a startup repair and...]Restore further back - restored to 2 days ago, and I'd had many reboots since then with no problem. Enable autologin to try to get beyond the login screen - done, doesn't work. It seems the best advice is complete reinstall, but I really don't want to do that because it'll take 3-4 days to add all the apps I use. Some key points to note - in both states - before and after removing the video driver, I always had a mouse cursor on the screen. CTL-ALT-DEL flashes up the login background, but no login info. I can (and often do) reinstall from scratch, but was at a fairly stable state before this, and would prefer not to. -Paul

    Read the article

  • .htaccess redirect working on localhost but not on server

    - by Thread7
    I want users who hit my web site's root directory to be sent to a subdirectory. So anyone going to: http://MyDomain.com or /index.php would be sent to http://MyDomain.com/subdir I used the .htaccess file to successfully do this on my local machine (with Apache 2). But it doesn't work on the server? Users still see the default index.php in the root directory. Here is my simple .htaccess file. Any ideas? RewriteEngine On Redirect /index.php http://MyDomain.com/subdir/ Now my httpd.conf file AccessFileName .htaccess <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory "/var/www/icons"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> </IfModule> </IfModule>

    Read the article

  • Inverse Kinematics with OpenGL/Eigen3 : unstable jacobian pseudoinverse

    - by SigTerm
    I'm trying to implement simple inverse kinematics test using OpenGL, Eigen3 and "jacobian pseudoinverse" method. The system works fine using "jacobian transpose" algorithm, however, as soon as I attempt to use "pseudoinverse", joints become unstable and start jerking around (eventually they freeze completely - unless I use "jacobian transpose" fallback computation). I've investigated the issue and turns out that in some cases jacobian.inverse()*jacobian has zero determinant and cannot be inverted. However, I've seen other demos on the internet (youtube) that claim to use same method and they do not seem to have this problem. So I'm uncertain where is the cause of the issue. Code is attached below: *.h: struct Ik{ float targetAngle; float ikLength; VectorXf angles; Vector3f root, target; Vector3f jointPos(int ikIndex); size_t size() const; Vector3f getEndPos(int index, const VectorXf& vec); void resize(size_t size); void update(float t); void render(); Ik(): targetAngle(0), ikLength(10){ } }; *.cpp: size_t Ik::size() const{ return angles.rows(); } Vector3f Ik::getEndPos(int index, const VectorXf& vec){ Vector3f pos(0, 0, 0); while(true){ Eigen::Affine3f t; float radAngle = pi*vec[index]/180.0f; t = Eigen::AngleAxisf(radAngle, Vector3f(-1, 0, 0)) * Eigen::Translation3f(Vector3f(0, 0, ikLength)); pos = t * pos; if (index == 0) break; index--; } return pos; } void Ik::resize(size_t size){ angles.resize(size); angles.setZero(); } void drawMarker(Vector3f p){ glBegin(GL_LINES); glVertex3f(p[0]-1, p[1], p[2]); glVertex3f(p[0]+1, p[1], p[2]); glVertex3f(p[0], p[1]-1, p[2]); glVertex3f(p[0], p[1]+1, p[2]); glVertex3f(p[0], p[1], p[2]-1); glVertex3f(p[0], p[1], p[2]+1); glEnd(); } void drawIkArm(float length){ glBegin(GL_LINES); float f = 0.25f; glVertex3f(0, 0, length); glVertex3f(-f, -f, 0); glVertex3f(0, 0, length); glVertex3f(f, -f, 0); glVertex3f(0, 0, length); glVertex3f(f, f, 0); glVertex3f(0, 0, length); glVertex3f(-f, f, 0); glEnd(); glBegin(GL_LINE_LOOP); glVertex3f(f, f, 0); glVertex3f(-f, f, 0); glVertex3f(-f, -f, 0); glVertex3f(f, -f, 0); glEnd(); } void Ik::update(float t){ targetAngle += t * pi*2.0f/10.0f; while (t > pi*2.0f) t -= pi*2.0f; target << 0, 8 + 3*sinf(targetAngle), cosf(targetAngle)*4.0f+5.0f; Vector3f tmpTarget = target; Vector3f targetDiff = tmpTarget - root; float l = targetDiff.norm(); float maxLen = ikLength*(float)angles.size() - 0.01f; if (l > maxLen){ targetDiff *= maxLen/l; l = targetDiff.norm(); tmpTarget = root + targetDiff; } Vector3f endPos = getEndPos(size()-1, angles); Vector3f diff = tmpTarget - endPos; float maxAngle = 360.0f/(float)angles.size(); for(int loop = 0; loop < 1; loop++){ MatrixXf jacobian(diff.rows(), angles.rows()); jacobian.setZero(); float step = 1.0f; for (int i = 0; i < angles.size(); i++){ Vector3f curRoot = root; if (i) curRoot = getEndPos(i-1, angles); Vector3f axis(1, 0, 0); Vector3f n = endPos - curRoot; float l = n.norm(); if (l) n /= l; n = n.cross(axis); if (l) n *= l*step*pi/180.0f; //std::cout << n << "\n"; for (int j = 0; j < 3; j++) jacobian(j, i) = n[j]; } std::cout << jacobian << std::endl; MatrixXf jjt = jacobian.transpose()*jacobian; //std::cout << jjt << std::endl; float d = jjt.determinant(); MatrixXf invJ; float scale = 0.1f; if (!d /*|| true*/){ invJ = jacobian.transpose(); scale = 5.0f; std::cout << "fallback to jacobian transpose!\n"; } else{ invJ = jjt.inverse()*jacobian.transpose(); std::cout << "jacobian pseudo-inverse!\n"; } //std::cout << invJ << std::endl; VectorXf add = invJ*diff*step*scale; //std::cout << add << std::endl; float maxSpeed = 15.0f; for (int i = 0; i < add.size(); i++){ float& cur = add[i]; cur = std::max(-maxSpeed, std::min(maxSpeed, cur)); } angles += add; for (int i = 0; i < angles.size(); i++){ float& cur = angles[i]; if (i) cur = std::max(-maxAngle, std::min(maxAngle, cur)); } } } void Ik::render(){ glPushMatrix(); glTranslatef(root[0], root[1], root[2]); for (int i = 0; i < angles.size(); i++){ glRotatef(angles[i], -1, 0, 0); drawIkArm(ikLength); glTranslatef(0, 0, ikLength); } glPopMatrix(); drawMarker(target); for (int i = 0; i < angles.size(); i++) drawMarker(getEndPos(i, angles)); } Any help will be appreciated.

    Read the article

  • Intermittent wired network issues in 14.04

    - by Tommy Brunn
    Since yesterday, my wired network connection has been dropping for a couple of seconds every 30 seconds or so. To my knowledge, I had not made any changes to my network. Output of ifconfig -a: ? ~ ifconfig -a eth0 Link encap:Ethernet HWaddr 6c:f0:49:b9:b1:7f inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:feb9:b17f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11597 errors:0 dropped:0 overruns:0 frame:0 TX packets:9783 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10101682 (10.1 MB) TX bytes:1215142 (1.2 MB) Interrupt:48 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:96691 errors:0 dropped:0 overruns:0 frame:0 TX packets:96691 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13594355 (13.5 MB) TX bytes:13594355 (13.5 MB) lspci |grep Ethernet: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) Pinging my router: ? ~ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.435 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.571 ms ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable 64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=1.03 ms And the output of route: ? ~ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 1 0 0 eth0 Some messages from /var/logs/syslog: ? ~ tail -f /var/log/syslog Jun 6 10:37:34 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:34 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:37 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:37 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:39 lolbox dhclient: XMT: Solicit on eth0, interval 8660ms. Jun 6 10:37:39 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:39 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:47 lolbox dhclient: XMT: Solicit on eth0, interval 16820ms. Jun 6 10:37:47 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:47 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:04 lolbox dhclient: XMT: Solicit on eth0, interval 34410ms. Jun 6 10:38:04 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:04 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13045 Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:37:34 lolbox whoopsie[1133]: online Jun 6 10:38:16 lolbox whoopsie[1133]: offline Jun 6 10:38:16 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:38:16 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13044 Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:38:16 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:17 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:17 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:17 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:18 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13160 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13161 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:38:18 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:18 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:18 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:18 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:18 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:18 lolbox dhclient: All rights reserved. Jun 6 10:38:18 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:18 lolbox dhclient: Jun 6 10:38:19 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:19 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:19 lolbox dhclient: All rights reserved. Jun 6 10:38:19 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:19 lolbox dhclient: Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:38:19 lolbox dhclient: Bound to *:546 Jun 6 10:38:19 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:38:19 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv6 state changed nbi -> preinit6 Jun 6 10:38:19 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on Socket/fallback Jun 6 10:38:19 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3fc9376d) Jun 6 10:38:19 lolbox dhclient: XMT: Solicit on eth0, interval 1020ms. Jun 6 10:38:19 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:19 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:38:20 lolbox dhclient: bound to 192.168.0.16 -- renewal in 41481 seconds. Jun 6 10:38:20 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:38:20 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:38:20 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:38:20 lolbox dhclient: XMT: Solicit on eth0, interval 2110ms. Jun 6 10:38:20 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:20 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:38:21 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:38:21 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:38:21 lolbox whoopsie[1133]: online Jun 6 10:38:21 lolbox ntpdate[13217]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:38:21 lolbox ntpdate[13217]: no servers can be used, exiting Jun 6 10:38:22 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:38:22 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:38:22 lolbox dhclient: XMT: Solicit on eth0, interval 4080ms. Jun 6 10:38:22 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:22 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:26 lolbox dhclient: XMT: Solicit on eth0, interval 8450ms. Jun 6 10:38:26 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:26 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:35 lolbox dhclient: XMT: Solicit on eth0, interval 16630ms. Jun 6 10:38:35 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:35 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:51 lolbox dhclient: XMT: Solicit on eth0, interval 34860ms. Jun 6 10:38:51 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:51 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:58 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:38:58 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13161 Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:22 lolbox whoopsie[1133]: online Jun 6 10:39:04 lolbox whoopsie[1133]: offline Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:39:04 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:39:04 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13160 Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:39:04 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:05 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:05 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:05 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:06 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13270 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13271 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:39:07 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:07 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:07 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:07 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:07 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:07 lolbox dhclient: All rights reserved. Jun 6 10:39:07 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:07 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:08 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:08 lolbox dhclient: All rights reserved. Jun 6 10:39:08 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:08 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Bound to *:546 Jun 6 10:39:08 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:39:08 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:39:08 lolbox kernel: [ 1446.098590] type=1400 audit(1402043948.002:75): apparmor="DENIED" operation="signal" profile="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=13273 comm="nm-dhcp-client." requested_mask="send" denied_mask="send" signal=term peer="/sbin/dhclient" Jun 6 10:39:08 lolbox kernel: [ 1446.098599] type=1400 audit(1402043948.002:76): apparmor="DENIED" operation="signal" profile="/sbin/dhclient" pid=13273 comm="nm-dhcp-client." requested_mask="receive" denied_mask="receive" signal=term peer="/usr/lib/NetworkManager/nm-dhcp-client.action" Jun 6 10:39:08 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:39:08 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on Socket/fallback Jun 6 10:39:08 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3e0183b9) Jun 6 10:39:08 lolbox dhclient: XMT: Solicit on eth0, interval 1050ms. Jun 6 10:39:08 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:39:08 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:39:09 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:39:09 lolbox dhclient: bound to 192.168.0.16 -- renewal in 35498 seconds. Jun 6 10:39:09 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:39:09 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:39:09 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:10 lolbox dhclient: XMT: Solicit on eth0, interval 2180ms. Jun 6 10:39:10 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:10 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:39:10 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:39:10 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:39:10 lolbox whoopsie[1133]: online Jun 6 10:39:10 lolbox ntpdate[13339]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:39:10 lolbox ntpdate[13339]: no servers can be used, exiting Jun 6 10:39:11 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:39:11 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:39:12 lolbox dhclient: XMT: Solicit on eth0, interval 4350ms. Jun 6 10:39:12 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:12 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:16 lolbox dhclient: XMT: Solicit on eth0, interval 8740ms. Jun 6 10:39:16 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:16 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:17 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:17 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:25 lolbox dhclient: XMT: Solicit on eth0, interval 17610ms. Jun 6 10:39:25 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:25 lolbox dhclient: IA_NA status code NoAddrsAvail.

    Read the article

  • KnpLabs / DoctrineBehaviors Translatable - currentLocale = null

    - by Ruben
    Using the trait \Knp\DoctrineBehaviors\Model\Translatable\Translation inside an Entity, I see that the property currentLocale is never setted , so we always obtain the default locale ('en') in all the calls to $this->translate(). If I change this getDefaultLocale, all the translations are made correctly, so I think that is no problem with the fallback. I tried debug the currentLocaleCallable. I see that if I put a "var_dump ($this-container-get('request'));" in the contructor of currentLocaleCallable, the request have a locale to null. And outside the request has the correct locale.It seems that container is not in the scope: request , i don't know how can I get it to work I post an issue in github https://github.com/KnpLabs/DoctrineBehaviors/issues/71 EDITED This service is defined in vendor/knplabs/doctrine-behaviors/config/orm-services.yml and is: knp.doctrine_behaviors.reflection.class_analyzer: class: "%knp.doctrine_behaviors.reflection.class_analyzer.class%" public: false knp.doctrine_behaviors.translatable_listener: class: "%knp.doctrine_behaviors.translatable_listener.class%" public: false arguments: - "@knp.doctrine_behaviors.reflection.class_analyzer" - "%knp.doctrine_behaviors.reflection.is_recursive%" - "@knp.doctrine_behaviors.translatable_listener.current_locale_callable" tags: - { name: doctrine.event_subscriber } knp.doctrine_behaviors.translatable_listener.current_locale_callable: class: "%knp.doctrine_behaviors.translatable_listener.current_locale_callable.class%" arguments: - "@service_container" # lazy request resolution public: false EDIT 2: My composer.json "php": ">=5.3.3", "symfony/symfony": "2.3.*", "doctrine/orm": ">=2.2.3,<2.4-dev", "doctrine/doctrine-bundle": "1.2.*", "twig/extensions": "1.0.*", "symfony/assetic-bundle": "2.3.*", "symfony/swiftmailer-bundle": "2.3.*", "symfony/monolog-bundle": "2.3.*", "sensio/distribution-bundle": "2.3.*", "sensio/framework-extra-bundle": "2.3.*", "sensio/generator-bundle": "2.3.*", "incenteev/composer-parameter-handler": "~2.0", "friendsofsymfony/user-bundle": "1.3.*", "avalanche123/imagine-bundle": "v2.1", "raulfraile/ladybug-bundle": "~1.0", "genemu/form-bundle": "2.2.*", "friendsofsymfony/rest-bundle": "0.12.0", "stof/doctrine-extensions-bundle": "dev-master", "sonata-project/admin-bundle": "dev-master", "a2lix/translation-form-bundle": "1.*@dev", "sonata-project/user-bundle": "dev-master", "psliwa/pdf-bundle": "dev-master", "jms/serializer-bundle": "dev-master", "jms/di-extra-bundle": "dev-master", "knplabs/doctrine-behaviors": "dev-master", "sonata-project/doctrine-orm-admin-bundle": "dev-master", "knplabs/knp-paginator-bundle": "dev-master", "friendsofsymfony/jsrouting-bundle": "~1.1", "zendframework/zend-validator": ">=2.0.0-rc2", "zendframework/zend-barcode": ">=2.0.0-rc2"

    Read the article

  • Loading cross domain XML with Javascript using a hybrid iframe-proxy/xsl/jsonp concept?

    - by Josef
    On our site www.foo.com we want to download and use http://feeds.foo.com/feed.xml with Javascript. We'll obviously use Access-Control but for browsers that don't support it we are considering the following as a fallback: On www.foo.com, we set document.domain, provide a callback function and load the feed into a (hidden) iframe: document.domain = 'foo.com'; function receive_data(data) { // process data }; var proxy = document.createElement('iframe'); proxy.src = 'http://feeds.foo.com/feed.xml'; document.body.appendChild(proxy); On feeds.foo.com, add an XSL to feed.xml and use it to transform the feed into an html document that also sets document.domain and calls the callback function in its parent with the feed data as json: <?xml version="1.0"?> <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" version="1.0"> <xsl:template match="ROOT"> <html><body> <script type="text/javascript"> document.domain = 'foo.com'; parent.receive_data([<xsl:apply-templates/>]); </script> </body></html> </xsl:template> <!-- templates that transform data into json objects go here --> </xsl:stylesheet> Is there a better way to load XML from feeds.foo.com and what are the ramifications of this iframe-proxy/xslt/jsonp trick? (..and in what cases will it fail?) Remarks This does not work in Safari & Chrome but since both support Access-Control it's fine. We want little or no change to feeds.foo.com We are aware of (but not interested in) server-side proxy solutions update: wrote about it

    Read the article

  • Programmatically convert *.odt file to MS Word *.doc file using an OpenOffice.org basic macro

    - by Chen Levy
    I am trying to build a reStructuredText to MS Word document tool-chain, so I will be able to save only the rst sources in version control. So far I -- Have rst2odt.py to convert reStructuredText to OpenOffice.org Writer format. Next I want to use the most recent OpenOffice.org (currently 3.1) that do a pretty decent work of generating a Word 97/2000/XP document, so I wrote the macro: sub ConvertToWord(file as string) rem ---------------------------------------------------------------------- rem define variables dim document as object dim dispatcher as object rem ---------------------------------------------------------------------- rem get access to the document document = ThisComponent.CurrentController.Frame dispatcher = createUnoService("com.sun.star.frame.DispatchHelper") rem ---------------------------------------------------------------------- dim odf(1) as new com.sun.star.beans.PropertyValue odf(0).Name = "URL" odf(0).Value = "file://" + file + ".odt" odf(1).Name = "FilterName" odf(1).Value = "MS Word 97" dispatcher.executeDispatch(document, ".uno:Open", "", 0, odf()) rem ---------------------------------------------------------------------- dim doc(1) as new com.sun.star.beans.PropertyValue doc(0).Name = "URL" doc(0).Value = "file://" + file + ".doc" doc(1).Name = "FilterName" doc(1).Value = "MS Word 97" dispatcher.executeDispatch(document, ".uno:SaveAs", "", 0, doc()) end sub But when I executing it: soffice "macro:///Standard.Module1.ConvertToWord(/path/to/odt_file_wo_ext)" I get a: "BASIC runtime error. Property or method not found." message On the line: document = ThisComponent.CurrentController.Frame And when I comment that line, the above invocation complete without error, but do nothing. I guess I need to somehow set the value of document to a newly created instance, but I don't know how to do it. Or am I going at it at a completely backward way? P.S. I will consider JODConverter as a fallback, because I try to minimize my dependencies.

    Read the article

  • Grails Mail port configuration

    - by bsreekanth
    Hello, I am trying to send mail through grails mail plugin. I configured according to the documentation, and also followed few blog posts (http://blog.lourish.com/2010/04/02/sending-asynchronous-html-email-in-grails-with-activemq-jms-and-gmail/). That post mention that the closure way of declaring the configuration overrides others, but not true. Anyway I tried both approach, but seems like the port is still use the smtp default one. I get the below exception. exception: org.springframework.mail.MailSendException: Mail server connection failed; nested exception is javax.mail.MessagingException: Could not connect to SMTP host: localhost, port: 25; nested exception is: java.net.ConnectException: Connection refused: connect Now, I wrote a small program directly using the java mail library, and I could send the mail with that. The configuration is shown below. tried additional config "mail.smtp.port":"465"", but no change.. used the parameters mentioned in the above blog post, result same grails { mail { host = "smtp.gmail.com" port = "465" username = "[email protected]" password = "mypwd" props = ["mail.smtp.auth":"true", // "mail.smtp.port":"465", "mail.smtp.socketFactory.port":"465", "mail.smtp.socketFactory.class":"javax.net.ssl.SSLSocketFactory", "mail.smtp.socketFactory.fallback":"false"] } } thanks in advance.. Update: It is not port or firewall config, as when I made a grails application from scratch, and tried with the same config, everything works. Also, asked in grails forum http://grails.1312388.n4.nabble.com/grails-mail-mailSender-does-not-have-config-values-td2237704.html#a2237704 . Hope get a lead to try.

    Read the article

  • Mercurial fails while commiting/updating/etc. using Mercuriual+TrueCrypt+MAC

    - by lukewar
    While trying to work with Mercurial on project located on TrueCrypt partition I always get en error as follows: ** unknown exception encountered, details follow ** report bug details to http://mercurial.selenic.com/bts/ ** or [email protected] ** Mercurial Distributed SCM (version 1.5.2+20100502) ** Extensions loaded: Traceback (most recent call last): File "/usr/local/bin/hg", line 27, in mercurial.dispatch.run() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 16, in run sys.exit(dispatch(sys.argv[1:])) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 30, in dispatch return _runcatch(u, args) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 50, in _runcatch return _dispatch(ui, args) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 470, in _dispatch return runcommand(lui, repo, cmd, fullargs, ui, options, d) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 340, in runcommand ret = _runcommand(ui, options, cmd, d) File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 521, in _runcommand return checkargs() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 475, in checkargs return cmdfunc() File "/Library/Python/2.6/site-packages/mercurial/dispatch.py", line 469, in d = lambda: util.checksignature(func)(ui, *args, **cmdoptions) File "/Library/Python/2.6/site-packages/mercurial/util.py", line 401, in check return func(*args, **kwargs) File "/Library/Python/2.6/site-packages/mercurial/commands.py", line 3332, in update return hg.update(repo, rev) File "/Library/Python/2.6/site-packages/mercurial/hg.py", line 362, in update stats = _merge.update(repo, node, False, False, None) File "/Library/Python/2.6/site-packages/mercurial/merge.py", line 495, in update _checkunknown(wc, p2) File "/Library/Python/2.6/site-packages/mercurial/merge.py", line 77, in _checkunknown for f in wctx.unknown(): File "/Library/Python/2.6/site-packages/mercurial/context.py", line 660, in unknown return self._status[4] File "/Library/Python/2.6/site-packages/mercurial/util.py", line 156, in get result = self.func(obj) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 622, in _status return self._repo.status(unknown=True) File "/Library/Python/2.6/site-packages/mercurial/localrepo.py", line 1023, in status if (f not in ctx1 or ctx2.flags(f) != ctx1.flags(f) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 694, in flags flag = findflag(self._parents[0]) File "/Library/Python/2.6/site-packages/mercurial/context.py", line 690, in findflag return ff(path) File "/Library/Python/2.6/site-packages/mercurial/dirstate.py", line 145, in f if 'x' in fallback(x): TypeError: argument of type 'NoneType' is not iterable It is worth mention that Mercurial works perfectly if project is not located on TrueCrypt partition. Configuration: MacOS X 10.6.3 Mercurial Distributed SCM (version 1.5.2+20100502) Python 2.6.5 Have anyone of you generous people able to help me? :)

    Read the article

  • Excel Regex, or export to Python? ; "Vlookup" in Python?

    - by victorhooi
    heya, We have an Excel file with a worksheet containing people records. 1. Phone Number Sanitation One of the fields is a phone number field, which contains phone numbers in the format e.g.: +XX(Y)ZZZZ-ZZZZ (where X, Y and Z are integers). There are also some records which have less digits, e.g.: +XX(Y)ZZZ-ZZZZ And others with really screwed up formats: +XX(Y)ZZZZ-ZZZZ / ZZZZ or: ZZZZZZZZ We need to sanitise these all into the format: 0YZZZZZZZZ (or OYZZZZZZ with those with less digits). 2. Fill in Supervisor Details Each person also has a supervisor, given as an numeric ID. We need to do a lookup to get the name and email address of that supervisor, and add it to the line. This lookup will be firstly on the same worksheet (i.e. searching itself), and it can then fallback to another workbook with more people. 3. Approach? For the first issue, I was thinking of using regex in Excel/VBA somehow, to do the parsing. My Excel-fu isn't the best, but I suppose I can learn...lol. Any particular points on this one? However, would I be better off exporting the XLS to a CSV (e.g. using xlrd), then using Python to fix up the phone numbers? For the second approach, I was thinking of just using vlookups in Excel, to pull in the data, and somehow, having it fall through, first on searching itself, then on the external workbook, then just putting in error text. Not sure how to do that last part. However, if I do happen to choose to export to CSV and do it in Python, what's an efficient way of doing the vlookup? (Should I convert to a dict, or just iterate? Or is there a better, or more idiomatic way?) Cheers, Victor

    Read the article

  • How does FallbackValue work with a MultiBiding?

    - by Will
    I ask because it doesn't seem to work. Assume we're binding to the following object: public class HurrDurr { public string Hurr {get{return null;}} public string Durr {get{return null;}} } Well, it would appear that if we used a MultiBinding against this the fallback value would be shown, right? <TextBlock> <TextBlock.Text> <MultiBinding StringFormat="{}{0} to the {1}" FallbackValue="Not set! It works as expected!)"> <Binding Path="Hurr"/> <Binding Path="Durr"/> </MultiBinding> </TextBlock.Text> </TextBlock> However the result is, in fact, " to the ". Even forcing the bindings to return DependencyProperty.UnsetValue doesn't work: <TextBlock xmnlns:base="clr-namespace:System.Windows;assembly=WindowsBase"> <TextBlock.Text> <MultiBinding StringFormat="{}{0} to the {1}" FallbackValue="Not set! It works as expected!)"> <Binding Path="Hurr" FallbackValue="{x:Static base:DependencyProperty.UnsetValue}" /> <Binding Path="Durr" FallbackValue="{x:Static base:DependencyProperty.UnsetValue}" /> </MultiBinding> </TextBlock.Text> </TextBlock> Tried the same with TargetNullValue, which was also a bust all the way around. So it appears that MultiBinding will never ever use FallbackValue. Is this true, or am I missing something?

    Read the article

  • jquery selector logical AND?

    - by taber
    In jQuery I'm trying to select only mount nodes where a and b's text values are 64 and "test" accordingly. I'd also like to fallback to 32 if no 64 and "test" exist. What I'm seeing with the code below though, is that the 32 mount is being returned instead of the 64. The XML: <thingses <thing <a32</a <-- note, a here is 32 and not 64 -- <other...</other <mountsample 1</mount <btest</b </thing <thing <a64</a <other...</other <mountsample 2</mount <btest</b </thing <thing <a64</a <other...</other <mountsample 3</mount <bunrelated</b </thing <thing <a128</a <other...</other <mountsample 4</mount <bunrelated</b </thing </thingses And unfortunately I don't have control over the XML as it comes from somewhere else. What I'm doing now is: var ret_val = ''; $data.find('thingses thing').each(function(i, node) { var $node = $(node), found_node = $node.find('b:first:is(test), a:first:is(64)').end().find('mount:first').text(); if(found_node) { ret_val = found_node; return; } found_node = $node.find('b:first:is(test), a:first:is(32)').end().find('mount:first').text(); if(found_node) { ret_val = found_node; return; } ret_val = 'not found'; }); // expected result is "sample 2", but if sample 2's parent "thing" was missing, the result would be "sample 1" alert(ret_val); For my ":is" selector I'm using: if(jQuery){ jQuery.expr[":"].is = function(obj, index, meta, stack){ return (obj.textContent || obj.innerText || $(obj).text() || "").toLowerCase() == meta[3].toLowerCase(); }; } There has to be a better way than how I'm doing it. I wish I could replace the "," with "AND" or something. :) Any help would be much appreciated. thanks!

    Read the article

  • HTML5 <video> callbacks?

    - by Andrew
    I'm working on a site for a client and they're insistent on using HTML5's video tag as the delivery method for some of their video content. I currently have it up and running with a little help from http://videojs.com/ to handle the Internet Explorer Flash fallback. One thing they've asked me to do is, after the videos finish playing (they're all a different length), fade them out and then fade a picture in place of the video --- think of it like a poster frame after the video. Is this even possible? Can you get the timecode of a currently playing movie via Javascript or some other method? I know Flowplayer (http://flowplayer.org/demos/scripting/grow.html) has an onFinish function, is that the route I should take in lieu of the HTML5 video method? Does the fact that IE users will be getting a Flash player require two separate solutions? Any input would be greatly appreciated. I'm currently using jQuery on the site, so I'd like to keep the solution in that realm if at all possible. Thanks!

    Read the article

  • C# Error reading two dates from a binary file

    - by Jamie
    Hi all, When reading two dates from a binary file I'm seeing the error below: "The output char buffer is too small to contain the decoded characters, encoding 'Unicode (UTF-8)' fallback 'System.Text.DecoderReplacementFallback'. Parameter name: chars" My code is below: static DateTime[] ReadDates() { System.IO.FileStream appData = new System.IO.FileStream( appDataFile, System.IO.FileMode.Open, System.IO.FileAccess.Read); List<DateTime> result = new List<DateTime>(); using (System.IO.BinaryReader br = new System.IO.BinaryReader(appData)) { while (br.PeekChar() > 0) { result.Add(new DateTime(br.ReadInt64())); } br.Close(); } return result.ToArray(); } static void WriteDates(IEnumerable<DateTime> dates) { System.IO.FileStream appData = new System.IO.FileStream( appDataFile, System.IO.FileMode.Create, System.IO.FileAccess.Write); List<DateTime> result = new List<DateTime>(); using (System.IO.BinaryWriter bw = new System.IO.BinaryWriter(appData)) { foreach (DateTime date in dates) bw.Write(date.Ticks); bw.Close(); } } What could be the cause? Thanks

    Read the article

  • How can I test this SQL Server performance Utility?

    - by Martin Smith
    As part of my MSc I need to do a three month project later this year. I have decided to do something which will likely be useful for me in the workplace and spend the time getting to understand SQL Server internals. The deliverable for this project will be a performance advisor looking at a variety of different rules. Some static such as finding redundant indexes, some more dynamic such as using XEvents to find outlying invocations of stored procedure execution times when certain parameters are passed. I am struggling to come up with a good way of testing this though. I can obviously design a "bad" database and a synthetic workload that my tool will pick up issues on but I also need to demonstrate that it has real world utility. Looking at the self tuning database literature it is common to use TPC benchmarks but I've had a look at the TPCC site and it looks very time consuming to implement and not that good a fit to my project's testing needs in any event (I would still be able to "rig" it by the decisions I made on indexing or physical architecture). Plan A would be to find willing beta tester(s) but in the event that isn't possible I will need a fallback plan. The best idea I have come up with so far is to use the various MS sample applications as examples of real world applications. e.g. http://msftdpprodsamples.codeplex.com/ http://www.asp.net/community/projects/ Does anyone have any better suggestions?

    Read the article

  • How to use routing in a ASP MVC website to localize in two languages - But keeping exiting URLs

    - by Anders Pedersen
    We have a couple ASP MVC websites just using the standard VS templates default settings - Working as wanted. But now I want to localize these website ( They are now in Dutch and I will add the English language ) I would like to use routing and not Resource because: 1. Languages will differ in content, numbers of pages, etc. 2. The content is mostly text. I would like the URLs to look some thing like this - www.domain.com/en/Home/Index, www.domain.nl/nl/Home/Index. But the last one should also work with - www.domain.nl/Home/Index - Witch is the exciting URLs. I have implemented Phil Haacks areas ViewEngine from this blogpost - http://haacked.com/archive/2008/11/04/areas-in-aspnetmvc.aspx. But only putting the English website in the areas and keeping the Dutch in old structure. Witch are served as Phils default fallback. But the problem is here that I have to duplicate my controllers for both language's. So I tried the work method described in this tread - http://stackoverflow.com/questions/1712167/asp-net-mvc-localization-route. It works OK with the ?en? and /nl/ but not with the old URLs. When using this code in the global.asax the URL without the culture isn't working. public static void RegisterRoutes(RouteCollection routes) { //routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.MapRoute( "Default", // Route name "{culture}/{controller}/{action}/{id}", // URL with parameters new { culture = "nl-NL", controller = "Home", action = "Index", id = "" } // Parameter defaults ); routes.MapRoute( "DefaultWitoutCulture", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Home", action = "Index", id = "" } // Parameter defaults ); } I properly overlooking some thing simple but I can't get this to work for me. Or are there a better way of doing this?

    Read the article

  • JavaEE : "Access to default session denied" when sending mail using smtp.gmail.com

    - by Harry Pham
    I am trying to write email authentication feature for my website and I encounter some issues. I got java.lang.SecurityException: Access to default session denied, when I try to do Session.getDefaultInstance. Here are my codes: private static final String SMTP_HOST_NAME = "smtp.gmail.com"; private static final String SMTP_PORT = "465"; private static final String emailSubjectTxt = "Email Confirmation"; private static final String emailFromAddress = "[email protected]"; private static final String SSL_FACTORY = "javax.net.ssl.SSLSocketFactory"; ... String sendTo = "[email protected]"; boolean debug = true; Properties props = new Properties(); props.put("mail.smtp.host", SMTP_HOST_NAME); props.put("mail.smtp.auth", "true"); props.put("mail.debug", "true"); props.put("mail.smtp.port", SMTP_PORT); props.put("mail.smtp.socketFactory.port", SMTP_PORT); props.put("mail.smtp.socketFactory.class", SSL_FACTORY); props.put("mail.smtp.socketFactory.fallback", "false"); //It dies at the next line Session session = Session.getDefaultInstance(props, new javax.mail.Authenticator() { @Override protected PasswordAuthentication getPasswordAuthentication() { return new PasswordAuthentication("myUserName", "myPassword"); } }); session.setDebug(debug); //Set the FROM address Message msg = new MimeMessage(session); InternetAddress addressFrom = new InternetAddress(emailFromAddress); msg.setFrom(addressFrom); //Set the TO address InternetAddress[] addressTo = new InternetAddress[1]; addressTo[0] = new InternetAddress(sendTo); msg.setRecipients(Message.RecipientType.TO, addressTo); //Construct the content of the email confirmation String message = "Test Content" // Setting the Subject and Content Type msg.setSubject(emailSubjectTxt); msg.setContent(message, "text/plain"); Transport.send(msg);

    Read the article

  • Pros and cons of MPMoviePlayerController versus launching UIWebView to stream movie

    - by Nosredna
    I have a client who has video content for the web in Flash format. My task is to help them show the videos in an iPhone app. I realize that step one is to get these videos into the appropriate Quicktime format for the iPhone. Then I'm going to have to help the client figure out how or where to host these files. If that's tricky I assume they can be hosted at YouTube. My chief concern, though, is which approach to take to stream the video. What are the pros and cons of MPMoviePlayerController versus launching UIWebView with the URL of the stream? Is there any difference? Is one of them more or less forgiving? Is one of them a better user experience? Any gotchas I might expect to run into? I'm assuming playing video is pretty easy on the iPhone. Is it reasonable to try both and have one available as a fallback, or would that be a waste of time? I'm trying to schedule this out a bit, so I'd love to hear real-world experiences from anyone who's done this.

    Read the article

  • Http Digest Authentication, Handle different browser char-sets...

    - by user160561
    Hi all, I tried to use the Http Authentication Digest Scheme with my php (apache module) based website. In general it works fine, but when it comes to verification of the username / hash against my user database i run into a problem. Of course i do not want to store the user´s password in my database, so i tend to store the A1 hashvalue (which is md5($username . ':' . $realm . ':' . $password)) in my db. This is just how the browser does it too to create the hashes to send back. The Problem: I am not able to detect if the browser does this in ISO-8859-1 fallback (like firefox, IE) or UTF-8 (Opera) or whatever. I have chosen to do the calculation in UTF-8 and store this md5 hash. Which leads to non-authentication in Firefox and IE browsers. How do you solve this problem? Just do not use this auth-scheme? Or Store a md5 Hash for each charset? Force users to Opera? (Terms of A1 refer to the http://php.net/manual/en/features.http-auth.php example.) (for digest access authentication read the according wikipedia entry)

    Read the article

  • How to change default locale in BIRT

    - by zlajo
    Hi everybody, I am working with the BIRT reporting engine and my current task is to implement internationalization for reports. We are using the webviewer to generate and download pdf reports. There is a parameter (__locale) which allows me to specify the locale that should be used to generate a report. So far everything works fine. There is an additional requirement I have not been able to implement, though. Additionally to the locale which is set by the http parameter there should also be the possibility to specify some kind of fallback locale. Take the following example: There are two property-files common_en_US.properties and common_en_GB.properties. The first locale to be used should be en_GB (__locale=en_GB). Everything works fine if the common_en_GB.properties file exist. But I would also like to tell BIRT to use common_en_US.properties if the en_GB-file cannot be found, which does not work as expected. I tried to solve this by manually setting the Java default locale before executing BIRT because I thought that BIRT would use the Java mechanism to resolve localized strings. Unfortunately this attempt does not work. Is there a different way to do what I would like to do? Is it possible to do something like that at all? Thanks a lot! Johannes

    Read the article

  • How do you detect when the Flowplayer has started playing the video?

    - by Alex
    Hi. I'm using the Flowplayer Flash video player to play MP4 videos inside an AnythingSlider. I need to detect when the user has clicked the start button on the video so to stop the slideshow and allow the user to view the video. I've tried using this code just to get an alert box but it doesn't do anything (the code is at the end of the page, before the closing </body> tag): <script type="text/javascript"> $f("player","global/js/flowplayer/flowplayer-3.1.5.swf",{ onStart: function(clip) { alert('player started'); } }); </script> The Flowplayer is implemented as part of the html5media library, which automatically detects whether the browser can handle the <video> tag; if not, it replaces the anchor tag below with the Flowplayer: <video id="vid" width="372" height="209" poster="global/vid/bbq-poster.jpg" controls preload> <source id="videoSource" src="global/vid/BBQ_Festival.mp4" type='video/mp4; codecs="avc1.42E01E, mp4a.40.2"' onerror="fallback(this.parentNode)" ></source> <a href="global/vid/BBQ_Festival.mp4" style="display:block;width:372px;height:209px; padding-left:5px; " id="player"> </a> </video> So the $f() function call is in a JavaScript block at the end of the page, to give the player a chance to load correctly. What am I doing wrong? Thanks.

    Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19  | Next Page >