Search Results

Search found 1870 results on 75 pages for 'mrjimoy 05'.

Page 13/75 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• Need help identiying a nasty rootkit in Windows

  - by goofrider

  I have a nasty rootkit that not tools seem to be able to idenity. I know for sure it's a rootkit, but I can figure out which rootkit it is. Here's what I gathered so far: It creates multiple copies of itself in %HOME%\Local Settings\Temp with names like Q.EXE, IAJARZ.exe, etc., and install them as hidden services. These EXE have SysInternals identifiers in them so they're definitely rootkits. It hooked very deep in the system, including file read/write, security policies, registry read/write, and possibly WinSock/TCP/IP. When going to Sophos.com to download their software, the rootkit inject something called Microsoft Ajax Tootkit into the page, which injects code into the email submission form in order to redirect it. (EDIT: I might have panicked. Looks like Sophos does use an AJAZ email form, their form is just broken on Chrome so it looked like a mail form injection attack, the link is http://www.sophos.com/en-us/products/free-tools/virus-removal-tool/download.aspx ) Super-Antispyware found a lot of spyware cookies, in the name of .kaspersky.2o7.net, etc. (just chedk 2o7.net, looks like it's a legit ad company) I tried comparing DNS lookup from the infected systems and from system in other physical locations, no DNS redirections it seems. I used dd to copy the MBR and compared it with the MBR provided by ms-sys package, no differences so it's not infecting MBR. No antivirus or rootkit scanner be able to identify it. Most of them can't even find it. I tried scanning, in-situ (normal mode), in safe mode, and boot to linux live CD. Scanners used: Avast, Sophos anti rootkit, Kasersky TDSSKiller, GMER, RootkitRevealer, and many others. Kaspersky reported some unsigned system files that ought to be signed (e.g. tcpip.sys), and reported a number of MD5 mismatches. But otherwise couldn't identify anything based on signature. When running Sysinternal RootkitRevealer and Sophos AntiRootkit, CPU usage goes up to 100% and gets stucked. The Rootkit is blocking them. When trying running/installing HiJackThis, RootkitRevealer and some other scanners, it tells me system security policy prevent running/installing it. The list of malicious acitivities go on and on. here's a sample of logs from all my scans. In particular, aswSnx.SYS, apnenfno.sys and PROCMON20.SYS has a huge number of hooks. It's hard to tell if the rootkit replaced legit program files like aswSnx.SYS (from Avast) and PROCMON20.SYS (from Sysinternal Process Monitor). I can't find whether apnenfno.sys is from a legit program. Help to identify it is appreciated. Trend Micro RootkitBuster ------ [HIDDEN_REGISTRY][Hidden Reg Value]: KeyPath : HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\sptd\Cfg Root : 586bfc0 SubKey : Cfg ValueName : g0 Data : 38 23 E8 D0 BF F2 2D 6F ... ValueType : 3 AccessType: 0 FullLength: 61 DataSize : 32 [HOOKED_SERVICE_API]: Service API : ZwCreateMutant Image Path : C:\WINDOWS\System32\Drivers\aswSnx.SYS OriginalHandler : 0x8061758e CurrentHandler : 0xaa66cce8 ServiceNumber : 0x2b ModuleName : aswSnx.SYS SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwCreateThread Image Path : c:\windows\system32\drivers\apnenfno.sys OriginalHandler : 0x805d1038 CurrentHandler : 0xaa5f118c ServiceNumber : 0x35 ModuleName : apnenfno.sys SDTType : 0x0 [HOOKED_SERVICE_API]: Service API : ZwDeleteKey Image Path : C:\WINDOWS\system32\Drivers\PROCMON20.SYS OriginalHandler : 0x80624472 CurrentHandler : 0xa709b0f8 ServiceNumber : 0x3f ModuleName : PROCMON20.SYS SDTType : 0x0 HiJackThis ------ O23 - Service: JWAHQAGZ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\JWAHQAGZ.exe O23 - Service: LHIJ - Sysinternals - www.sysinternals.com - C:\DOCUME~1\jeff\LOCALS~1\Temp\LHIJ.exe Kaspersky TDSSKiller ------ 21:05:58.0375 3936 C:\WINDOWS\system32\ati2sgag.exe - copied to quarantine 21:05:59.0217 3936 ATI Smart ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0342 3936 C:\WINDOWS\system32\BUFADPT.SYS - copied to quarantine 21:05:59.0856 3936 BUFADPT ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:05:59.0965 3936 C:\Program Files\CrashPlan\CrashPlanService.exe - copied to quarantine 21:06:00.0152 3936 CrashPlanService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0246 3936 C:\WINDOWS\system32\epmntdrv.sys - copied to quarantine 21:06:00.0433 3936 epmntdrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0464 3936 C:\WINDOWS\system32\EuGdiDrv.sys - copied to quarantine 21:06:00.0526 3936 EuGdiDrv ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:00.0604 3936 C:\Program Files\Common Files\Macrovision Shared\FLEXnet Publisher\FNPLicensingService.exe - copied to quarantine 21:06:01.0181 3936 FLEXnet Licensing Service ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0321 3936 C:\Program Files\AddinForUNCFAT\UNCFATDMS.exe - copied to quarantine 21:06:01.0430 3936 OTFSDMS ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0492 3936 C:\WINDOWS\system32\DRIVERS\tcpip.sys - copied to quarantine 21:06:01.0539 3936 Tcpip ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0601 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - copied to quarantine 21:06:01.0664 3936 HKLM\SYSTEM\ControlSet003\services\TULPUWOX - will be deleted on reboot 21:06:01.0664 3936 C:\DOCUME~1\jeff\LOCALS~1\Temp\TULPUWOX.exe - will be deleted on reboot 21:06:01.0664 3936 TULPUWOX ( UnsignedFile.Multi.Generic ) - User select action: Delete 21:06:01.0757 3936 C:\WINDOWS\system32\Drivers\usbaapl.sys - copied to quarantine 21:06:01.0866 3936 USBAAPL ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:01.0913 3936 C:\Program Files\VMware\VMware Player\vmware-authd.exe - copied to quarantine 21:06:02.0443 3936 VMAuthdService ( UnsignedFile.Multi.Generic ) - User select action: Quarantine 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0443 3936 vmount2 ( UnsignedFile.Multi.Generic ) - User select action: Skip 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - skipped by user 21:06:02.0459 3936 vstor2 ( UnsignedFile.Multi.Generic ) - User select action: Skip

  Read the article

• codeblocks install failed. Dependency not resolved, libgcc1

  - by user204166

  I am trying to install codeblocks using ubuntu software center. I found it but when install, I get dependency not resolved, libgcc1...like that. My system ubuntu 12.04, 32bits. Any advice will be appreciated. detailed fail message: codeblocks:depends:libgcc1(=1:4.1.1) but 1:4.6.3-1ubuntu5 is to be installed depends:codeblocks-common(=10.05-2) but 12.11-2 is to be installed. I went to codeblocks "more info" button in Ubuntu software center and selected all the add-ons for codeblocks. Apply changes and now I get an additional (to the two above) dependency message:depends:libwxsmithlib0(=10.05-2) but 12.11-2 is to be installed.

  Read the article

• How do I install latest NVIDIA drivers?

  - by Shahe Tajiryan

  This is what I am trying to do. I downloaded the latest driver for my VGA from http://www.nvidia.com. The installation needs the X11 to be shut down, so I log out of my account, then press CTRL+ALT+F1, then log in with my username and passowrd, then run the command sh NVIDIA-Linux-x86_64-285.05.09.run in every possible way, I have even tried CHMODing the package with 777 permissions, but still I'm getting the sh: can't open NVIDIA-Linux-x86_64-285.05.09.run error. Any help would be greatly appreciated.

  Read the article

• How do I install the latest NVIDIA drivers from the .run file?

  - by Shahe Tajiryan

  This is what I am trying to do. I downloaded the latest driver for my VGA from http://www.nvidia.com. The installation needs the X11 to be shut down, so I log out of my account, then press Ctrl+Alt+F1, then log in with my username and password, then run the command sh NVIDIA-Linux-x86_64-285.05.09.run in every possible way, I have even tried CHMODing the package with 777 permissions, but still I'm getting the sh: can't open NVIDIA-Linux-x86_64-285.05.09.run error. Any help would be greatly appreciated.

  Read the article

• How do I install latest NVIDIA drivers from the .run file?

  - by Shahe Tajiryan

  This is what I am trying to do. I downloaded the latest driver for my VGA from http://www.nvidia.com. The installation needs the X11 to be shut down, so I log out of my account, then press CTRL+ALT+F1, then log in with my username and password, then run the command sh NVIDIA-Linux-x86_64-285.05.09.run in every possible way, I have even tried CHMODing the package with 777 permissions, but still I'm getting the sh: can't open NVIDIA-Linux-x86_64-285.05.09.run error. Any help would be greatly appreciated.

  Read the article

• Why does iOS 5 fail to connect to a server running JDK 1.6, but not JDK 1.5

  - by KC Baltz

  We have a Java Socket Server listening on an SSLSocket (port 443) and an iOS application that connects with it. When running on iOS 5.1, the application stopped working when we upgraded the Java version of the server from JDK 1.5 to 1.6 (or 1.7). The app connects just fine to JDK 5 and 6 when running on iOS 6. The iOS app is reporting an error: -9809 = errSSLCrypto. On the Java side, we get javax.net.ssl.SSLException: Received fatal alert: close_notify. On the Java server side, we have enabled all the available cipher suites. On the client side we have tested enabling several different suites, although we have yet to complete a test involving each one individually enabled. Right now, it is failing when we use TLS_DH_anon_WITH_AES_128_CBC_SHA although it has failed with others and we are starting to think it's not the suite. Here is the debug output. It makes it all the way to ServerHelloDone and then fails shortly thereafter: Is secure renegotiation: false [Raw read]: length = 5 0000: 16 03 03 00 41 ....A [Raw read]: length = 65 0000: 01 00 00 3D 03 03 50 83 1E 0B 56 19 25 65 C8 F2 ...=..P...V.%e.. 0010: AF 02 AD 48 FE E2 92 CF B8 D7 A6 A3 EA C5 FF 5D ...H...........] 0020: 74 0F 1B C1 99 18 00 00 08 00 FF 00 34 00 1B 00 t...........4... 0030: 18 01 00 00 0C 00 0D 00 08 00 06 05 01 04 01 02 ................ 0040: 01 . URT-, READ: Unknown-3.3 Handshake, length = 65 *** ClientHello, Unknown-3.3 RandomCookie: GMT: 1333992971 bytes = { 86, 25, 37, 101, 200, 242, 175, 2, 173, 72, 254, 226, 146, 207, 184, 215, 166, 163, 234, 197, 255, 93, 116, 15, 27, 193, 153, 24 } Session ID: {} Cipher Suites: [TLS_EMPTY_RENEGOTIATION_INFO_SCSV, TLS_DH_anon_WITH_AES_128_CBC_SHA, SSL_DH_anon_WITH_3DES_EDE_CBC_SHA, SSL_DH_anon_WITH_RC4_128_MD5] Compression Methods: { 0 } Unsupported extension signature_algorithms, data: 00:06:05:01:04:01:02:01 *** [read] MD5 and SHA1 hashes: len = 65 0000: 01 00 00 3D 03 03 50 83 1E 0B 56 19 25 65 C8 F2 ...=..P...V.%e.. 0010: AF 02 AD 48 FE E2 92 CF B8 D7 A6 A3 EA C5 FF 5D ...H...........] 0020: 74 0F 1B C1 99 18 00 00 08 00 FF 00 34 00 1B 00 t...........4... 0030: 18 01 00 00 0C 00 0D 00 08 00 06 05 01 04 01 02 ................ 0040: 01 . %% Created: [Session-1, TLS_DH_anon_WITH_AES_128_CBC_SHA] *** ServerHello, TLSv1 RandomCookie: GMT: 1333992972 bytes = { 100, 3, 56, 153, 7, 2, 251, 64, 41, 32, 66, 240, 227, 181, 55, 190, 2, 237, 146, 0, 73, 119, 70, 0, 160, 9, 28, 207 } Session ID: {80, 131, 30, 12, 241, 73, 52, 38, 46, 41, 237, 226, 199, 246, 156, 45, 3, 247, 182, 43, 223, 8, 49, 169, 188, 63, 160, 41, 102, 199, 50, 190} Cipher Suite: TLS_DH_anon_WITH_AES_128_CBC_SHA Compression Method: 0 Extension renegotiation_info, renegotiated_connection: <empty> *** Cipher suite: TLS_DH_anon_WITH_AES_128_CBC_SHA *** Diffie-Hellman ServerKeyExchange DH Modulus: { 233, 230, 66, 89, 157, 53, 95, 55, 201, 127, 253, 53, 103, 18, 11, 142, 37, 201, 205, 67, 233, 39, 179, 169, 103, 15, 190, 197, 216, 144, 20, 25, 34, 210, 195, 179, 173, 36, 128, 9, 55, 153, 134, 157, 30, 132, 106, 171, 73, 250, 176, 173, 38, 210, 206, 106, 34, 33, 157, 71, 11, 206, 125, 119, 125, 74, 33, 251, 233, 194, 112, 181, 127, 96, 112, 2, 243, 206, 248, 57, 54, 148, 207, 69, 238, 54, 136, 193, 26, 140, 86, 171, 18, 122, 61, 175 } DH Base: { 48, 71, 10, 213, 160, 5, 251, 20, 206, 45, 157, 205, 135, 227, 139, 199, 209, 177, 197, 250, 203, 174, 203, 233, 95, 25, 10, 167, 163, 29, 35, 196, 219, 188, 190, 6, 23, 69, 68, 64, 26, 91, 44, 2, 9, 101, 216, 194, 189, 33, 113, 211, 102, 132, 69, 119, 31, 116, 186, 8, 77, 32, 41, 216, 60, 28, 21, 133, 71, 243, 169, 241, 162, 113, 91, 226, 61, 81, 174, 77, 62, 90, 31, 106, 112, 100, 243, 22, 147, 58, 52, 109, 63, 82, 146, 82 } Server DH Public Key: { 8, 60, 59, 13, 224, 110, 32, 168, 116, 139, 246, 146, 15, 12, 216, 107, 82, 182, 140, 80, 193, 237, 159, 189, 87, 34, 18, 197, 181, 252, 26, 27, 94, 160, 188, 162, 30, 29, 165, 165, 68, 152, 11, 204, 251, 187, 14, 233, 239, 103, 134, 168, 181, 173, 206, 151, 197, 128, 65, 239, 233, 191, 29, 196, 93, 80, 217, 55, 81, 240, 101, 31, 119, 98, 188, 211, 52, 146, 168, 127, 127, 66, 63, 111, 198, 134, 70, 213, 31, 162, 146, 25, 178, 79, 56, 116 } Anonymous *** ServerHelloDone [write] MD5 and SHA1 hashes: len = 383 0000: 02 00 00 4D 03 01 50 83 1E 0C 64 03 38 99 07 02 ...M..P...d.8... 0010: FB 40 29 20 42 F0 E3 B5 37 BE 02 ED 92 00 49 77 .@) B...7.....Iw 0020: 46 00 A0 09 1C CF 20 50 83 1E 0C F1 49 34 26 2E F..... P....I4&. 0030: 29 ED E2 C7 F6 9C 2D 03 F7 B6 2B DF 08 31 A9 BC ).....-...+..1.. 0040: 3F A0 29 66 C7 32 BE 00 34 00 00 05 FF 01 00 01 ?.)f.2..4....... 0050: 00 0C 00 01 26 00 60 E9 E6 42 59 9D 35 5F 37 C9 ....&.`..BY.5_7. 0060: 7F FD 35 67 12 0B 8E 25 C9 CD 43 E9 27 B3 A9 67 ..5g...%..C.'..g 0070: 0F BE C5 D8 90 14 19 22 D2 C3 B3 AD 24 80 09 37 ......."....$..7 0080: 99 86 9D 1E 84 6A AB 49 FA B0 AD 26 D2 CE 6A 22 .....j.I...&..j" 0090: 21 9D 47 0B CE 7D 77 7D 4A 21 FB E9 C2 70 B5 7F !.G...w.J!...p.. 00A0: 60 70 02 F3 CE F8 39 36 94 CF 45 EE 36 88 C1 1A `p....96..E.6... 00B0: 8C 56 AB 12 7A 3D AF 00 60 30 47 0A D5 A0 05 FB .V..z=..`0G..... 00C0: 14 CE 2D 9D CD 87 E3 8B C7 D1 B1 C5 FA CB AE CB ..-............. 00D0: E9 5F 19 0A A7 A3 1D 23 C4 DB BC BE 06 17 45 44 ._.....#......ED 00E0: 40 1A 5B 2C 02 09 65 D8 C2 BD 21 71 D3 66 84 45 @.[,..e...!q.f.E 00F0: 77 1F 74 BA 08 4D 20 29 D8 3C 1C 15 85 47 F3 A9 w.t..M ).<...G.. 0100: F1 A2 71 5B E2 3D 51 AE 4D 3E 5A 1F 6A 70 64 F3 ..q[.=Q.M>Z.jpd. 0110: 16 93 3A 34 6D 3F 52 92 52 00 60 08 3C 3B 0D E0 ..:4m?R.R.`.<;.. 0120: 6E 20 A8 74 8B F6 92 0F 0C D8 6B 52 B6 8C 50 C1 n .t......kR..P. 0130: ED 9F BD 57 22 12 C5 B5 FC 1A 1B 5E A0 BC A2 1E ...W"......^.... 0140: 1D A5 A5 44 98 0B CC FB BB 0E E9 EF 67 86 A8 B5 ...D........g... 0150: AD CE 97 C5 80 41 EF E9 BF 1D C4 5D 50 D9 37 51 .....A.....]P.7Q 0160: F0 65 1F 77 62 BC D3 34 92 A8 7F 7F 42 3F 6F C6 .e.wb..4....B?o. 0170: 86 46 D5 1F A2 92 19 B2 4F 38 74 0E 00 00 00 .F......O8t.... URT-, WRITE: TLSv1 Handshake, length = 383 [Raw write]: length = 388 0000: 16 03 01 01 7F 02 00 00 4D 03 01 50 83 1E 0C 64 ........M..P...d 0010: 03 38 99 07 02 FB 40 29 20 42 F0 E3 B5 37 BE 02 .8....@) B...7.. 0020: ED 92 00 49 77 46 00 A0 09 1C CF 20 50 83 1E 0C ...IwF..... P... 0030: F1 49 34 26 2E 29 ED E2 C7 F6 9C 2D 03 F7 B6 2B .I4&.).....-...+ 0040: DF 08 31 A9 BC 3F A0 29 66 C7 32 BE 00 34 00 00 ..1..?.)f.2..4.. 0050: 05 FF 01 00 01 00 0C 00 01 26 00 60 E9 E6 42 59 .........&.`..BY 0060: 9D 35 5F 37 C9 7F FD 35 67 12 0B 8E 25 C9 CD 43 .5_7...5g...%..C 0070: E9 27 B3 A9 67 0F BE C5 D8 90 14 19 22 D2 C3 B3 .'..g......."... 0080: AD 24 80 09 37 99 86 9D 1E 84 6A AB 49 FA B0 AD .$..7.....j.I... 0090: 26 D2 CE 6A 22 21 9D 47 0B CE 7D 77 7D 4A 21 FB &..j"!.G...w.J!. 00A0: E9 C2 70 B5 7F 60 70 02 F3 CE F8 39 36 94 CF 45 ..p..`p....96..E 00B0: EE 36 88 C1 1A 8C 56 AB 12 7A 3D AF 00 60 30 47 .6....V..z=..`0G 00C0: 0A D5 A0 05 FB 14 CE 2D 9D CD 87 E3 8B C7 D1 B1 .......-........ 00D0: C5 FA CB AE CB E9 5F 19 0A A7 A3 1D 23 C4 DB BC ......_.....#... 00E0: BE 06 17 45 44 40 1A 5B 2C 02 09 65 D8 C2 BD 21 ...ED@.[,..e...! 00F0: 71 D3 66 84 45 77 1F 74 BA 08 4D 20 29 D8 3C 1C q.f.Ew.t..M ).<. 0100: 15 85 47 F3 A9 F1 A2 71 5B E2 3D 51 AE 4D 3E 5A ..G....q[.=Q.M>Z 0110: 1F 6A 70 64 F3 16 93 3A 34 6D 3F 52 92 52 00 60 .jpd...:4m?R.R.` 0120: 08 3C 3B 0D E0 6E 20 A8 74 8B F6 92 0F 0C D8 6B .<;..n .t......k 0130: 52 B6 8C 50 C1 ED 9F BD 57 22 12 C5 B5 FC 1A 1B R..P....W"...... 0140: 5E A0 BC A2 1E 1D A5 A5 44 98 0B CC FB BB 0E E9 ^.......D....... 0150: EF 67 86 A8 B5 AD CE 97 C5 80 41 EF E9 BF 1D C4 .g........A..... 0160: 5D 50 D9 37 51 F0 65 1F 77 62 BC D3 34 92 A8 7F ]P.7Q.e.wb..4... 0170: 7F 42 3F 6F C6 86 46 D5 1F A2 92 19 B2 4F 38 74 .B?o..F......O8t 0180: 0E 00 00 00 .... [Raw read]: length = 5 0000: 15 03 01 00 02 ..... [Raw read]: length = 2 0000: 02 00 .. URT-, READ: TLSv1 Alert, length = 2 URT-, RECV TLSv1 ALERT: fatal, close_notify URT-, called closeSocket() URT-, handling exception: javax.net.ssl.SSLException: Received fatal alert: close_notify FYI, this works in iOS 6.0

  Read the article

• Mac WLAN 802.11b+g WPA1 connection issues

  - by Peto

  Hi, I have a Telewell TW-EA510v4 ADSL modem+WLAN router configured as follows: Mode: 802.11b+g Security Mode: WPA1 Pre-shared Key WPA Algorithms: TKIP Connections from only certain MAC addresses have been allowed and the MAC address of my Mac is in that list. The WLAN works just fine with iPhone and an old Acer laptop. It has worked for about two months or so with my MacBook Pro (year and a half or so old model). Ocassionally i've had minor problems with it, which have required either reboot of ADSL modem or reboot of my Mac. However now, for the last week or so I haven't been able to connect to it at all. This is what is what i get in the console when i try to connect: 5.5.2010 20.54.53 airportd[73731] Apple80211Associate() failed -3924 (Invalid PMK) 5.5.2010 20.54.53 Apple80211 framework[584] airportd MIG failed (Associate Event) = -3924 (Invalid PMK) (port = 104599) 5.5.2010 20.54.53 SystemUIServer[584] Error joining WLAN-M: Invalid password (-3924 Invalid master key) The pre-shared key I use is not incorrect. I'm 100% sure of that. The Error Log from the router only says this when I try to connect to it: May 05 21:09:54 home.gateway:i802_1x:none: <my mac address> associated May 05 21:10:00 home.gateway:i802_1x:none: <my mac address> disassociated May 05 21:10:01 home.gateway:i802_1x:none: <my mac address> disassociated Any ideas or tips to troubleshoot this further?

  Read the article

• Every minute incoming, rejected connections to SMTP

  - by joltmode

  I have a feeling my server is being lazily DDoS'ed, though, I have never experienced it before, so, I may be wrong. Every minute, my journal logs the following 3 entries: Nov 05 21:10:47 <host> postfix/smtpd[11220]: connect from webmail.onvoy.com[199.199.18.10] Nov 05 21:10:47 <host> postfix/smtpd[11220]: NOQUEUE: reject: RCPT from webmail.onvoy.com[199.199.18.10]: 454 4.7.1 <tg@<DOMAIN>>: Relay access denied; from=<> to=<tg@<DOMAIN>> proto=ESMTP helo=<webmail.onvoy.com> Nov 05 21:10:47 <host> postfix/smtpd[11220]: disconnect from webmail.onvoy.com[199.199.18.10] Where <host> and <DOMAIN> are hidden. <DOMAIN>, though, is a domain registered with my NS that resolves to my box. How do I get rid of the messages and the related connections?

  Read the article

• Apache Process question about RAM usage

  - by Andrew Fashion

  So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

  Read the article

• Cannot login to ISCSI Target - hangs after sending login details

  - by Frank

  I have an ISCSI target volume, to which i am trying to connect using CentOS Linux server. Everything works fine, but cannot its stuck at login. Here are the steps i am performing: [root@neon ~]# iscsiadm -m node -l iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session20 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session21 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session22 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session23 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session30 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session31 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session78 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session79 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session80 iscsiadm: could not read session targetname: 5 iscsiadm: could not find session info for session81 Logging in to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) After this step, its stucks, waits for some time and then gives this output: Logging in to [iface: iface1, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260] (multiple) iscsiadm: Could not login to [iface: eql.eth2, target: iqn.2001-05.com.equallogic:0-8a0906-ab4764e0b-55ed2ef5cf350a66-neon105, portal: 10.10.1.1,3260]. My iscsi.conf is this: node.startup = automatic node.session.timeo.replacement_timeout = 15 # default 120; RedHat recommended node.conn[0].timeo.login_timeout = 15 node.conn[0].timeo.logout_timeout = 15 node.conn[0].timeo.noop_out_interval = 5 node.conn[0].timeo.noop_out_timeout = 5 node.session.err_timeo.abort_timeout = 15 node.session.err_timeo.lu_reset_timeout = 20 node.session.initial_login_retry_max = 8 # default 8; Dell recommended node.session.cmds_max = 1024 # default 128; Equallogic recommended node.session.queue_depth = 32 # default 32; Equallogic recommended node.session.iscsi.InitialR2T = No node.session.iscsi.ImmediateData = Yes node.session.iscsi.FirstBurstLength = 262144 node.session.iscsi.MaxBurstLength = 16776192 node.conn[0].iscsi.MaxRecvDataSegmentLength = 262144 discovery.sendtargets.iscsi.MaxRecvDataSegmentLength = 32768 node.conn[0].iscsi.HeaderDigest = None node.session.iscsi.FastAbort = Yes Also, in access control, i have given full access to Any IP, Any CHAP user and fixed iscsi initiator name. With same access level, all other volumes on rest of servers are working, except this one.

  Read the article

• Copy files from sub directories into one directory.

  - by Derek Organ

  Ok I have a bunch of files in this file structure format. /backup/daily/database1/database1-2011-01-01.sql /backup/daily/database1/database1-2011-01-02.sql /backup/daily/database1/database1-2011-01-03.sql /backup/daily/database1/database1-2011-01-04.sql /backup/daily/database1/database1-2011-01-05.sql /backup/daily/database1/database1-2011-01-06.sql /backup/daily/database1/database1-2011-01-07.sql /backup/daily/anotherdb/anotherdb-2011-01-01.sql /backup/daily/anotherdb/anotherdb-2011-01-02.sql /backup/daily/anotherdb/anotherdb-2011-01-03.sql /backup/daily/anotherdb/anotherdb-2011-01-04.sql /backup/daily/anotherdb/anotherdb-2011-01-05.sql /backup/daily/anotherdb/anotherdb-2011-01-06.sql /backup/daily/anotherdb/anotherdb-2011-01-07.sql /backup/daily/stuff/stuff-2011-01-01.sql /backup/daily/stuff/stuff-2011-01-02.sql /backup/daily/stuff/stuff-2011-01-03.sql /backup/daily/stuff/stuff-2011-01-04.sql /backup/daily/stuff/stuff-2011-01-05.sql /backup/daily/stuff/stuff-2011-01-06.sql /backup/daily/stuff/stuff-2011-01-07.sql And there are lots lots more. ultimately I want to import all the 2011-01-07.sql files into my mysql database. This works for one mysql -u root -ppassword < /backup/daily/database1/database1-2011-01-07.sql That will nicely restore that database from this backupfile. I want to run a process where it does this for all databases. So my plan is to first cp all 2011-01-07 sql files into a tmp dir e.g. cp /backup/daily/*/*2011-01-07*.sql /tmp/all The command above unfortunately isn't working I get an error: cp: cannot stat ..... No such file or directory So can you guys help me out with this. For bonus points if you can tell me how to do the next step which is import all databases in one command doing one at a time that would be great too. I really want to do these in two separate steps because I need to delete a few sql files manually from the tmp dir before I run the restore command. So I need: 1) command to copy all 2011-01-07 sql files to a tmp dir 2) command to import all those files in that dir into mysql I know its possible to do in one but for lots of reasons I really would prefer to do it in two steps.

  Read the article

• IP routing Solaris 9 access the internet from local network

  - by help_me

  I am trying to configure the NICS on the Solaris Sparc server. My problem lies in getting out to the "Internet" from the local network. I have requested the NIC to receive a DHCP server address #ifconfig -interface dhcp start. If anyone could guide me as to what I need to do next. I am not able to ping 4.2.2.2 or access the internet. Much appreciated, thank you #uname -a SunOS dev 5.9 Generic_122300-59 sun4u sparc SUNW,Sun-Fire-V210 ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.3 netmask ffffc000 broadcast 10.100.63.255 bge0:2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.22 netmask ffffc000 broadcast 10.100.63.255 bge3: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 12 inet 169.14.60.37 netmask fffffe00 broadcast 169.14.61.255 cat /etc/defaultrouter 10.100.0.254 169.14.60.1 cat /etc/resolv.conf nameserver 169.14.96.73 nameserver 169.10.8.4 netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 169.14.60.37 169.14.60.1 UGH 1 0 169.14.60.0 169.14.60.37 U 1 18 bge3 10.100.0.0 10.100.0.3 U 1 34940 bge0 10.100.0.0 10.100.0.22 U 1 0 bge0:2 224.0.0.0 10.100.0.3 U 1 0 bge0 default 10.100.0.254 UG 1 111 default 169.14.60.1 UG 1 26 127.0.0.1 127.0.0.1 UH 10 59464 lo0 bash-2.05$ sudo ndd -get /dev/ip bge0:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip bge3:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip ip_forwarding 1

  Read the article

• do I need to create an AD site for VPN network

  - by ykyri

  I have Windows Domain level 2008 R2. There are four GC DC in four different physical locations. I have Kerio-based VPN network for replication and remote administration. Here is how network configured: dc1: local IP: 192.168.0.10 VPN IP: 192.168.1.10 dc2: local IP: 10.10.8.11 VPN IP: 192.168.1.11 dc3: local IP: 10.10.9.12 VPN IP: 192.168.1.12 dc4: local IP: 10.10.10.13 VPN IP: 192.168.1.13 That's simple, replication and all works fine but when running dcdiag on dc3 I have an error: A warning event occurred. EventID: 0x000016AF During the past 4.12 hours there have been 216 connections to this Domain Controller from client machines whose IP addresses don't map to any of the existing sites in the enterprise. <...> The log(s) may contain additional unrelated debugging information. To filter out the needed information, please search for lines which contain text 'NO_CLIENT_SITE:'. The first word after this string is the client name and the second word is the client IP address. Here is netlogon.log lines example: 05/30 12:07:39 DOMAIN.NAME: NO_CLIENT_SITE: dc2 192.168.1.11 05/31 09:52:11 DOMAIN.NAME: NO_CLIENT_SITE: dc4 192.168.1.13 05/31 19:49:31 DOMAIN.NAME: NO_CLIENT_SITE: adm-note 192.168.1.101 07/01 05:16:26 DOMAIN.NAME: NO_CLIENT_SITE: dc1 192.168.1.10 All VPN-joined computers are generates same log line as above. Computer amd-note is for example administrator's notebook, also have VPN. Question is should I add new AD site and bind VPN subnet 192.168.1.0/24 with that site?

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• UIScrollView strange zoom behavior when content is a UIView subclass

  - by sigsegv

  Hi, I'm experiencing the following: I created a UIView subclass with a CATiledLayer as backing layer by overriding the layerClass method. The layer properties (delegate, tileSize, etc) are set in the initWithFrame: method of the subclass. +(Class)layerClass { return [CATiledLayer class]; } -(id)initWithFrame:(CGRect)frame { if(self = [super initWithFrame:frame]) { renderer = [[MFPDFRenderer alloc]init]; tiledLayer = (CATiledLayer *)[self layer]; [tiledLayer setFrame:frame]; [tiledLayer setLevelsOfDetail:2]; [tiledLayer setLevelsOfDetailBias:3]; [tiledLayer setTileSize:CGSizeMake(512, 512)]; [tiledLayer setDelegate:renderer]; } return self; } Then I add an instance of said class as the content of an UIScrollView and set UIScrollView properties and implement the required delegate's methods. Everything works fine but when zooming the scroll view keep repositioning itself on its center. It's hardly noticeable when zooming in the center of the content, but unbearable otherwise. The same scroll view works fine when I use as (zoomable) content any other view such as an UIImageView or even a normal UIView with a CATiledLayer with the same properties and delegate of the subclass implementation as sublayer. When I check layer bounds and frame in the drawLayer:inContext: method of the delegate I get the following result as the zoom increase UIView with CATiledLayer as sublayer: 2010-04-03 21:05:33.499 Renderer[89293:4903] Layer: (0.000, 0.000) 320.000 x 460.000 2010-04-03 21:05:33.500 Renderer[89293:4903] Bounds: (0.000, 0.000) 320.000 x 460.000 2010-04-03 21:05:33.529 Renderer[89293:4903] Layer: (0.000, 0.000) 320.000 x 460.000 2010-04-03 21:05:33.534 Renderer[89293:4903] Bounds: (0.000, 0.000) 320.000 x 460.000 Custom subclass: 2010-04-03 21:04:15.969 Renderer[88957:4903] Layer: (0.000, 0.000) 657.910 x 945.746 2010-04-03 21:04:15.970 Renderer[88957:4903] Bounds: (0.000, 0.000) 320.000 x 460.000 2010-04-03 21:04:17.428 Renderer[88957:4903] Layer: (-0.000, 0.000) 766.964 x 1102.510 2010-04-03 21:04:17.429 Renderer[88957:4903] Bounds: (0.000, 0.000) 320.000 x 460.000 [...] 2010-04-03 21:19:10.388 Renderer[92573:4903] Layer: (-0.000, 0.000) 905.680 x 1301.916 2010-04-03 21:19:10.388 Renderer[92573:4903] Bounds: (0.000, 0.000) 320.000 x 460.000 I suppose that's the culprit or at least another symptom. I can add that I get the same erratic behavior if my subclass is built over a standard CALayer with the same renderer. Any suggestion will be appreciated!

  Read the article

• 500 error but no info about the link GET / HTTP/1.1" 500 "-"

  - by Athanatos

  I am getting the following 500 in my access logs in rare occasions IP - - [05/Nov/2013:14:44:52 -0600] "-GET / HTTP/1.1" 500 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.0)" IP - - [05/Nov/2013:14:44:52 -0600] "GET / HTTP/1.1" 500 - "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.0)" However I cant see what page is throwing it so I was wondering how can I go about troubleshooting and find the page. Thanks

  Read the article

• "This Friday" in bash script

  - by Ben

  Hi, Is there a way to calculate a time stamp for the next coming up of a week day? So for instance, with friday, i'd like to be able to run some code that calculates that from today Wednesday 19/05/10, the next friday will be 21/05/10 and get a time stamp from it. I know the date command can parse a given string date according to a format, but I can't figure out how to calculate "next friday from today" Any idea? Cheers Ben

  Read the article

• Add elements to Arraylist and it replaces all previous elements in Java

  - by pie154

  I am adding elements to a ArrayList and it adds the first one correctly but then when I add any subsequent elements it wipes replaces the other elements with the value form the most recently added and adds a new element to the ArrayList. I ran test using arraylist and ints and even another created class and it worked perfectly but soemthing about the custon class i am using here causes problems. The code for the array list is public static void main(String args[]){ List<BasicEvent> list = new ArrayList<BasicEvent>(); list.add(new BasicEvent("Basic", "Door", 9, 4444, new Date(12,04,2010), new Time(12,04,21), 1, 0.98, 0)); list.add(new BasicEvent("Composite", "Door", 125, 4444, new Date(12,04,2010), new Time(12,04,20), 1, 0.98, 1)); list.add(new BasicEvent("Basic", "Door", 105, 88, new Date(12,04,2010), new Time(12,05,23), 1, 0.98, 0)); list.add(new BasicEvent("Basic", "Door", 125, 12, new Date(12,04,2010), new Time(12,05,28), 1, 0.98, 1)); list.add(new BasicEvent("Basic", "Door", 129, 25, new Date(12,04,2010), new Time(12,05,30), 1, 0.98, 0)); list.add(new BasicEvent("Basic", "Door", 125, 63, new Date(12,04,2010), new Time(12,04,20), 1, 0.98, 1)); list.add(new BasicEvent("Basic", "Detect", 127, 9, new Date(12,04,2010), new Time(12,05,29), 1, 0.98, -1)); for(int i=0;i<list.size();i++) {System.out.println("list a poition " + i + " is " + BasicEvent.basicToString(list.get(i)));} And the code for the custom class basicEvent is public class BasicEvent { public static String Level; public static String EType; public static double xPos; public static double yPos; public static Date date; public static Time time; public static double Rlb; public static double Sig; public static int Reserved; public BasicEvent(String L, String E, double X, double Y, Date D, Time T, double R, double S, int Res){ Level = L; EType = E; xPos = X; yPos = Y; date = D; time = T; Rlb = R; Sig = S; Reserved = Res; }; public static String basicToString(BasicEvent bse){ String out = bse.getLevel() + ";" + bse.getEtype() + ";" + bse.getxPos() + ";" + bse.getyPos() + ";" + bse.getDate().dateAsString() + ";" + bse.getTime().timeAsString() + ";" + bse.getRlb() + ";" + bse.getSig() + ";" + bse.getReserved(); return out; }

  Read the article

• I am converting general date to UniversalTime Please tell me how to get this format

  - by Rajesh Rolen- DotNet Developer

  i am converting my date to Universal Time using mydate.ToUniversalTime() in vb.net its giving me right time but its giving me time in "5/4/2010 4:30:00 AM" format (in vb.net) but i want it in "Wed, 05 May 2010 05:50:00 GMT" format.. please help me to make it in "Wed, 05 May 2010 05:50:00 GMT" format.

  Read the article

• Why can't I create a Date from a string including milliseconds?

  - by KooiInc

  In javascript you can create a Date object from a string, like var mydate = new Date('2008/05/10 12:08:20'); console.log(mydate); //=> Sat May 10 2008 12:08:20 GMT+0200 Now try this using milliseconds in the string var mydate = new Date('2008/05/10 12:08:20:551'); // or '2008/05/10 12:08:20.551' console.log(mydate); //=> NaN Just out of curiosity: why is this?

  Read the article

• what is the easiest way to do this function in c# ?

  - by From.ME.to.YOU

  Hello let say that we have an array [5,5] 01,02,03,04,05 06,07,08,09,10 11,12,13,14,15 16,17,18,19,20 21,22,23,24,25 the user should send 2 values to the function (start,searchFOR) for example (13,25) the function should search for that value in this way 07,08,09 12, ,14 17,18,19 if the value is n't found in this level it will goes a level higher 01,02,03,04,05 06, , , ,10 11, , , ,15 16, , , ,20 21,22,23,24,25 if the array is bigger than this and the value didn't found it will go to a level higher Thanks for your help

  Read the article

• Help with DateTime in format I need

  - by baron

  I am working with DateTime, trying to get date in the format like this: 03.05.2010-04.05.23 that is: dd.MM.yyyy-HH.mm.ss I'm using DateTime.ParseExact to try to achieve this (maybe wrong) So far I have: var dateInFormat = DateTime.ParseExact(DateTime.Now.ToShortDateString(), "dd.MM.yyyy.HH.mm.ss", null); But can't quite get exactly what I want. Basically I want to keep the 0, for example time is 05:03:20 PM I don't want it to show like 5:3:20 PM Any ideas?

  Read the article

• PHP curly string syntax question

  - by zildjohn01

  I'm running PHP 5.3.0. I've found that the curly string syntax only works when the first character of the expression is $. Is there a way to include other types of expressions (function calls, etc)? Trivial example: <?php $x = '05'; echo "{$x}"; // works as expected echo "{intval($x)}"; // hoped for "5", got "{intval(05)}"

  Read the article

• Is there a work around for invalid octal digit in an array?

  - by sircrisp

  I'm trying to create an array which will hold the hours in a day so I can loop through it for a clock. I have: int hourArray[24] = {12, 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11, 12, 01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11}; I am getting the error on the following numbers in order 08, 09, 08, 09. It tells me: Error: invalid octal digit I've never run into this before and I'm wondering if there is any way around it?

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >