Search Results

Search found 828 results on 34 pages for 'nf 81'.

Page 13/34 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• PASS Location fixed for the next 2 years - Are they listening?

  - by simonsabin

  I've just received the PASS connector newsletter with details of the decision of where to locate the next summits. To me it shows you how you can spin statistics they way you want to. I am very suprised by the numbers 81% said that they would like an east coast event. The spin is that "When we look at responses from only 2008 and 2009 Summit attendees (our most successful ones by far), the number who want a future Summit outside of Seattle drops to 69%." Wow the number drops thats bad. We must stay in Seattle then. My take however is that 69% of those willing to travel to Seattle want an event NOT in Seattle. Doesn't that suggest that people would like an event not in Seattle. I appreciate the comment about the launch years however 2012 isn't going to be a launch year because they need to get SQL out of the door before then to meet the 3 year software assurance cycle. So sticking 2012 in Seattle is IMHO a bad decision. It might keep the cost down for the PASS org, Microsoft and the attendees that live near Seattle but does it keep the cost down for the rest of the SQL Community? They do mention a possibility of an event on the East Coast and I do hope that its not just lip service. Flights for me to the East coast look ~30% cheaper than to Seattle and I've never been to the East Coast. Come on PASS show you are listening to the community.

  Read the article

• Install VMWare Tools from VMWare Workstation 7.1.1 build-282343 on Debian squeeze: complaint about gcc path not valid

  - by Misha Koshelev

  Dear All: I am trying to install VMWare tools on Debian Squeeze. My error: Before you can compile modules, you need to have the following installed... make gcc kernel headers of the running kernel Searching for GCC... The path "/usr/bin/gcc" is not valid path to the gcc binary. Would you like to change it? [yes] uname -a: Linux debian 2.6.32-5-686 #1 SMP Sat Sep 18 02:14:45 UTC 2010 i686 GNU/Linux dpkg -l | grep make ii make 3.81-8 An utility for Directing compilation. dpkg -l | grep gcc ii gcc 4:4.4.4-2 The GNU C compiler ii gcc-4.4 4.4.4-8 The GNU C compiler ii gcc-4.4-base 4.4.4-8 The GNU Compiler Collection (base package) ii libgcc1 1:4.4.4-8 GCC support library whereis gcc gcc: /usr/bin/gcc /usr/lib/gcc Thank you Misha

  Read the article

• Accessing internal server eg 192.168.10.10 without using remote desktop

  - by bergin

  Hi there My boss has an intranet he wants his employees to gain access to from the WWW. Theres a sharepoint server running on 192.168.10.10 and SBS can be seen from a website 81.244.232.22 (some numbers like this). When you access, theres a default internal sharepoint site "companyweb" but we dont want to use that we want the main sharepoint site which has all the business on it. is this possible? Currently we have to connect to a computer, chose the server and then get in that way. Any ideas?

  Read the article

• Accessing internal server eg 192.168.10.10 without using remote desktop

  - by bergin

  Hi there My boss has an intranet he wants his employees to gain access to from the WWW. Theres a sharepoint server running on 192.168.10.10 and SBS can be seen from a website 81.244.232.22 (some numbers like this). When you access, theres a default internal sharepoint site "companyweb" but we dont want to use that we want the main sharepoint site which has all the business on it. is this possible? Currently we have to connect to a computer, chose the server and then get in that way. Any ideas?

  Read the article

• VPN trace route

  - by Jake

  I am inside an Active Directory (AD) domain and trying to trace route to another AD domain at a remote site, but supposedly connected by VPN in between. the local domain can be accessed at 192.168.3.x and the remote location 192.168.2.x. When I do a tracert, I am suprised to see that the results did not show the intermediate ISP nodes. If I used the public IP of the remote location, then a normal tracert going through every intermediate node would show. 1 <1 ms <1 ms <1 ms 192.168.3.1 2 1 ms <1 ms <1 ms 192.168.3.254 3 7 ms 7 ms 7 ms 212.31.2xx.xx 4 197 ms 201 ms 196 ms 62.6.1.2xx 5 201 ms 201 ms 210 ms vacc27.norwich.vpn-acc.bt.net [62.6.192.87] 6 209 ms 209 ms 209 ms 81.146.xxx.xx 7 209 ms 209 ms 209 ms COMPANYDOMAIN [192.168.2.6] Can someone explain how does this VPN tunnelling works? Does this mean VPN is technically faster than without?

  Read the article

• Want to add a new domain to my postfix, but mails not delivered (mail look back to myself)

  - by user74850

  Hi everybody, My host relay is working but I was aksed to add a new domain (like external.example.com). I have added in main.cf the new fqdn in relay_domains relay_domains = $mydestination, example.com,example2.com, externe.example.com and in transport example.com smtp:[192.168.1.22] example2.com smtp:[192.168.1.22] external.example.com smtp:[192.168.1.22] Mails sent to users with example.com and example2.com domain are well delivered. But for mails to external.example.com i got this message Mar 17 16:47:52 relayhost postfix/smtp[11948]: 754E1876A01: to=<[email protected]>, relay=relayhost2.example.com[80.81.82.83]:25, delay=19555, delays=19525/0.01/30/0, dsn=4.4.6, status=deferred (mail for external.example.com loops back to myself) I read another Q/A about the same issue right here, but it's not helping me. Can you ?

  Read the article

• WMII Terminal Width of 80 Columns for xterm (colrules)

  - by BCable

  I'm trying to get WMII to split horizontally at 80 columns for xterm, but I'm only seeing a way to do this via percentage. It would be nice to be able to set it by something other than percentage for various resolutions, but if I have to deal with that I will. The problem is that even percentages don't work at my resolution (1366x768). 47+47 in /colrules yields 79 characters and 48+48 yields 81 characters. As far as I can tell, there is no decimal system allowed so I could do 47.5 for instance. I came from Ion3 and I'm used to using 80 column terminals, resizable by the keyboard, to get a reasonable cut off point for VIM when I'm coding. I would just settle with using the mouse, but WMII seems to be much more fluid than Ion3, so I would have to do it a LOT, which sounds annoying. Any ideas?

  Read the article

• Is a disk/ata timeout exception dangerous?

  - by j-g-faustus

  I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

  Read the article

• Retrieving a specific value from "df -h" using shell

  - by Diego Dias

  When I use df -h, I get the following output: Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 59G 2.2G 54G 4% / /dev/sda1 122M 38M 78M 33% /boot tmpfs 1.1G 0 1.1G 0% /dev/shm 10.10.0.105:/somepath 11T 8.4T 2.1T 81% /storage4 10.11.0.101:/somepath 15T 8.9T 5.9T 61% /storage1 /dev/mapper/patha 5.0T 255G 4.8T 5% /storage5_vol0 /dev/mapper/pathb 5.0T 195G 4.9T 4% /storage5_vol1 /dev/mapper/pathc 5.0T 608G 4.5T 12% /storage5_vol2 I want to write a script that gets the value of Avail column on a specific storage. I used to use df -k /storage_name | tail -1 | awk '{print $3}' But the FileSystem column can have a value or not .. which would change the variable of my script from $3 to $4. How can I get the Avail on a single command line even if there are no values on the previous columns?

  Read the article

• 9 Gigapixel Photo Captures 84 Million Stars

  - by Jason Fitzpatrick

  The European Southern Observatory has released an absolutely enormous picture of the center of the Milky Way captured by their VISTA telescope–the image is 9 gigapixels and captures over 84 million stars. From the press release: The large mirror, wide field of view and very sensitive infrared detectors of ESO’s 4.1-metre Visible and Infrared Survey Telescope for Astronomy (VISTA) make it by far the best tool for this job. The team of astronomers is using data from the VISTA Variables in the Via Lactea programme (VVV), one of six public surveys carried out with VISTA. The data have been used to create a monumental 108 200 by 81 500 pixel colour image containing nearly nine billion pixels. This is one of the biggest astronomical images ever produced. The team has now used these data to compile the largest catalogue of the central concentration of stars in the Milky Way ever created. Want to check out all 9 billion glorious pixels in their uncompressed state? Be prepared to wait a bit, the uncompressed image is available for download but it weighs in at a massive 24.6GB. 84 Million Stars and Counting [via Wired] How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

  Read the article

• Copying unicode symbols from Firefox address bar as is

  - by sindikat

  Let's say I open a webpage with some Unicode characters, say, Cyrillic, in the address like this: http://ru.wikipedia.org/wiki/??????????????_?????????????? When I try to copy it from the address bar somewhere else, it becomes unreadable rubbish: http://ru.wikipedia.org/wiki/%D0%A4%D1%83%D0%BD%D0%BA%D1%86%D0%B8%D0%BE%D0%BD%D0%B0%D0%BB%D1%8C%D0%BD%D0%B0%D1%8F_%D0%B7%D0%B0%D0%BA%D1%80%D0%B5%D0%BF%D0%BB%D1%91%D0%BD%D0%BD%D0%BE%D1%81%D1%82%D1%8C I guess this is for compatibility. However for readability I want to copy it straight away with proper Unicode characters. What and how should I tweak to make that possible?

  Read the article

• Ubuntu 64bit Black Screen on Minecraft

  - by Signify

  I have tried posting on the forums, but I really need help (I'm a server admin and really don't want to have to switch to Windows just to run Minecraft). Anyhow, I originally was running openjdk6 as I was told that 7 was unstable and was getting periodical lag spikes while walking (at least once every 3 seconds the screen would freeze for a tenth of a second). After that, I attempted to install Sun's Java JDK7 (I couldn't get ahold of 6 without signing up for Oracle's newsletters). Upon attempting to run Minecraft, I got a black screen after logging in with this error message: 27 achievements 182 recipes Setting user: Thunder7102, -1618112820878091307 Exception in thread "Minecraft main thread" java.lang.UnsatisfiedLinkError: /home/noiro/.minecraft/bin/natives/liblwjgl.so: /home/noiro/.minecraft/bin/natives/liblwjgl.so: wrong ELF class: ELFCLASS32 (Possible cause: architecture word width mismatch) at java.lang.ClassLoader$NativeLibrary.load(Native Method) at java.lang.ClassLoader.loadLibrary1(ClassLoader.java:1939) at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1864) at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1825) at java.lang.Runtime.load0(Runtime.java:792) at java.lang.System.load(System.java:1059) at org.lwjgl.Sys$1.run(Sys.java:69) at java.security.AccessController.doPrivileged(Native Method) at org.lwjgl.Sys.doLoadLibrary(Sys.java:65) at org.lwjgl.Sys.loadLibrary(Sys.java:81) at org.lwjgl.Sys.<clinit>(Sys.java:98) at org.lwjgl.opengl.Display.<clinit>(Display.java:132) at net.minecraft.client.Minecraft.a(SourceFile:184) at net.minecraft.client.Minecraft.run(SourceFile:657) at java.lang.Thread.run(Thread.java:722) Now, this got me fed up, so I tried to install a Windows 7 virtual machine through virtualbox, I gave it 256mb of graphics memory with 2D and 3D acceleration and 3GB of RAM. I installed Java JDK7 for Windows (which does work from experience on my other Windows 7 partition). Once again, a black screen after login. What the heck is going on guys? My System Specs: Ubuntu 12.04 64bit Fully Updated running Gnome3 Nvidia GTS 450 1.3GB OC'd AMD Athlon II 4x 2.8Ghz 6GB of RAM So, what do you think?

  Read the article

• How to know if my nginx is in good health?

  - by Howard

  I am running a nginx on EC2 (m1.small) for SSL termination. I am using 2 workers on Ubuntu, with latest nginx (stable), the network throughput is around 2Mbps and system load average is around 2 to 3. I am wondering if this system is in good health for now, e.g. what is the queue length (I know nginx can handle a lot of concurrent request, but I mean before the request is being served, how many of them need to wait before being served) what is the average queue time for a given request to be served. I want to know because if my nginx is cpu bounded (e.g. due to SSL), I will need to upgrade to a faster instance. My current nginx status Active connections: 4076 server accepts handled requests 90664283 90664283 104117012 Reading: 525 Writing: 81 Waiting: 3470

  Read the article

• Trouble opening my router to my web server

  - by Justin Heather Barrios

  Here's the story. I have a webs server created and connected to my router. The website works great when I'm connected to the router, but when I'm off the network I can't access the website. I got the IP for my router by googling "what is my ip." I have opened ports 80 to 10080 to link to the server in the router. One odd thing that I don't understand. When I am in network if I access XXX.XXX.XX.XX:80 I can access the web page no problem. If I access XXX.XXX.XX.XX:81 (or any other port) I get the error "Cannot access server." Any idea what the problem could be? Could it be my ISP?

  Read the article

• How to do port forwarding in D-link Glb802c?

  - by Manish

  I have some questions about port forwarding on my D-Link Router GLB-802C. For example: My local machine's IP is 117.1.1.81 My router's IP is 117.1.1.1 My Public (Web) IP is 117.16.1.1 My questions are: What will be my Global Address 'To'? What will be my Global Address 'From'? In Destination Port "From" and "To" what do I select in the drop down list and port no for forwarding HTTP traffic (for my website)? In Local Port, what do I select in drop down list and port no?

  Read the article

• Pick Up BioShock and Bioshock 2 for Price of a Big Mac Meal

  - by Jason Fitzpatrick

  Pre-ordering just opened on the third-installment of the highly-acclaimed horror-survival game series BioShock, BioShock Infinite. As part of the pre-order promotions, you can pick up a bundled copy of BioShock and BioShock 2 for a song. For the unfamiliar, BioShock is an atmospheric first-person-shooter backed up by an incredible storyline set in the underwater utopian-turned-dystopian city of Rapture. BioShock 2 continues the story in Rapture and the upcoming release (Febuary 2013) of BioShock Infinite takes place in the same game universe but fifty years before the events of the first two installments. If that seems like the kind of game you could dig into, Amazon has the Windows-platform version of BioShock and BioShock 2 bundled together for a scant $7.49–81% off the Steam and general retail price. The best part about the promotion is you can either download the games from Amazon or, for those of you that use Steam, you can simply plug the game product key into Steam. You can read more about the both the original two games and the upcoming release at the official BioShock site. BioShock Dual Pack [via Geeks Are Sexy] How Hackers Can Disguise Malicious Programs With Fake File Extensions Can Dust Actually Damage My Computer? What To Do If You Get a Virus on Your Computer

  Read the article

• How to do port forwarding in D-link Glb802c?

  - by Manish

  I have some questions about port forwarding on my D-Link Router GLB-802C. For example: My local machine's IP is 117.1.1.81 My router's IP is 117.1.1.1 My Public (Web) IP is 117.16.1.1 My questions are: What will be my Global Address 'To'? What will be my Global Address 'From'? In Destination Port "From" and "To" what do I select in the drop down list and port no for forwarding HTTP traffic (for my website)? In Local Port, what do I select in drop down list and port no?

  Read the article

• How do I improve terrain rendering batch counts using DirectX?

  - by gamer747

  We have determined that our terrain rendering system needs some work to minimize the number of batches being transferred to the GPU in order to improve performance. I'm looking for suggestions on how best to improve what we're trying to accomplish. We logically split our terrain mesh into smaller grid cells which are 32x32 world units. Each cell has meta data that dictates the four 256x256 textures that are used for spatting along with the alpha blend data, shadow, and light mappings. Each cell contains 81 vertices in a 9x9 grid. Presently, we examine each cell and determine the four textures that are being used to spat the cell. We combine that geometry with any other cell that perhaps uses the same four textures regardless of spat order. If the spat order for a cell differs, the blend map is adjusted so that the spat order is maintained the same as other like cells and blending happens in the right order too. But even with this batching approach, it isn't uncommon when looking out across an area of open terrain to have between 1200-1700 batch count depending upon how frequently textures differ or have different texture blends are between cells. We are only doing frustum culling presently. So using texture spatting, are there other alternatives that can reduce the batch count and allow rendering to be extremely performance-friendly even under DirectX9c? We considered using texture atlases since we're targeting DirectX 9c & older OpenGL platforms but trying to repeat textures using atlases and shaders result in seam artifacts which we haven't been able to eliminate with the exception of disabling mipmapping. Disabling mipmapping results in poor quality textures from a distance. How have others batched together terrain geometry such that one could spat terrain using various textures, minimizing batch count and texture state switches so that rendering performance isn't negatively impacted?

  Read the article

• Configuring IIS site to use HTTPS

  - by James

  I am working on a REST API which I have currently deployed on a Win XP Professional SP2 development machine running IIS 5.1. The site is currently being hosted on port 81 and being accessed via HTTP. I would now like to configure the site to stop using HTTP and use HTTPS only. I have developed a self-signed certificate using the SelfSSL.exe tool from the 6.0 Resource Kit Tools and set the Common Name to be the IP of my server (as it's a local development machine it has no domain name). I have also already configured the site to use SSL using the How To Set Up an HTTPS Service in IIS tutorial as my guide. However, whenever I try to access a resource in the API via HTTPS I get a 404. Any ideas?

  Read the article

• Issue about mapping MAC address to Ipv6 address

  - by deepsky

  I know that the address in ipv6 with prefix range 001 to 111 should use a 64-bit interface identifier that follows the EUI-64 format, which translates the MAC to ipv6 as below. MAC:00-02-b3-1e-83-29 --> 02-02-b3-ff-fe-1e-83-29 --->ipv6 addr: fe80::202:b3ff:fe1e:8329 Then I checked my network status with ipconfig /all on my windows XP, but it seems my ipv6 address doesn't follow the above rule: MAC:00-24-81-XX-XX-XX ipv6 addr:2001:da8:8006:225:0:24:81XX:XXXX Obviously it doesn't follow the EUI-64 format. Instead it just directly use the MAC as the last 8 bytes. Anyone know the reason? Pls Correct me if I am wrong.

  Read the article

• Apache SMTP connection times out

  - by Kaivosukeltaja

  A web server that has successfully sent mail using the hosting providers's SMTP server before seems to suddenly have lost connection to the SMTP server. [Wed Nov 28 09:51:27 2012] [error] [client 10.250.11.81] PHP Warning: fsockopen(): unable to connect to smtp.ourprovider.net:25 (Connection timed out) in /var/www/(....)/phpmailer/class.smtp.php on line 105, referer: http://oursite.net/sendmessage.php# If I telnet to the SMTP server's port 25 manually from the web server, I'm able to connect and send mail with no problems whatsoever. The web server is running RHEL 6.3 and Apache 2.2.15. The SE boolean httpd_can_network_connect is on. Our PHP version is 5.3.3. Where should I start looking to fix this?

  Read the article

• After upgrade to 12.04 wireless keeps dropping on BCM4312

  - by Sheket

  I know there are plenty of questions very similar to these, but I've tried practically everything and it still isn't working. Some solutions get the wireless connection working, but it goes very slow and drops after a few minutes. Then it won't reconnect and keeps asking for password. Hope you can help me. Thanks in advance. This is the output for sudo lshw -C network *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:f0300000-f0303fff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: c0 serial: 00:23:5a:9b:6e:b1 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:42 memory:f0200000-f023ffff ioport:a000(size=128) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:24:2c:83:f0:81 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-30-generic firmware=478.104 link=no multicast=yes wireless=IEEE 802.11bg And for lsmod | grep b43 b43 342643 0 mac80211 436455 1 b43 cfg80211 178679 2 b43,mac80211 bcma 25651 1 b43 ssb 50691 1 b43 And for rfkill list 5: phy0: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Don't understand [0:0] iptable syntax

  - by artaxerxe

  I'm struggling with some iptables rules. I'm a newbie in iptables. I found some resources where I get the following command related to iptables. This is stored in a file that will be executed. [0:0] -A PREROUTING -s 10.1.0.0/24 -p tcp -m tcp --dport 81 -j DNAT --to-destination 10.1.0.6:3128 Can anybody explain me what does [0:0] mean? Also, some link related to this in iptables are welcome. Thanks in advance! P.S. If you need more rules, just let me know.

  Read the article

• 2012 EC Election Results

  - by heathervc

  The 2012 Fall Executive Committee Election process is now complete. The ballot closed at midnight pacific time on Monday, 29 October.  Congratulations to Cinterion Wireless Modules GmbH, Credit Suisse, Fujitsu Limited, Hewlett-Packard (all four candidates were ratified),  and CloudBees and London Java Community (two elected candidates) as the new and re-elected merged EC Members. For more information regarding the merged EC, please refer to JSR 355 and the JCP 2.9 Process Document. Ratified Seats: Cinterion Wireless Modules GmbH, Credit Suisse, Fujitsu Limited and Hewlett-Packard Open Election Seats: CloudBees and London Java Community Newly elected EC Members take their seats on Tuesday, 13 November 2012. Detailed Election Results:Number of Eligible Voters: 1131 Percent of Eligible Members Casting Votes: 23.70% Ratified Seats: Candidate Yes Votes (%) No Votes (%) Abstentions Cinterion Wireless Modules GmbH 156 (76) 48 (24) 64 Credit Suisse 205 (85) 35 (15) 28 Fujitsu Limited 195 (85) 35 (15) 38 Hewlett-Packard 182 (81) 44 (19) 42 Open Election Seats: The top two candidates have been elected. Candidate Votes (%) Cisco Systems 37 (7) CloudBees 101 (20) Giuseppe Dell'Abate 6 (1) Liferay, Inc. 35 (7) London Java Community 164 (33) MoroccoJUG 46 (9) North Sixty-One Ltd 26 (5) Software AG 19 (4) ZeroTurnaround 64 (13) None of the above 5 (1) For more information about the candidates who ran for the 2012 Executive Committee Election, please visit the 2012 Executive Committee Elections Nominees page.

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >