Search Results

Search found 21268 results on 851 pages for 'null route'.

Page 13/851 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

  • Cisco IOS policy route for router originated VPN traffic

    - by Paul
    We have a Cisco IOS router with two DSL connections. One of them is intended for general traffic (ADSL), the other for VPN links (BDSL) and various other traffic. So the default route is the ADSL link, and we have a combination of static routes for the VPN traffic, and policy routes for other traffic types that should go out the BDSL link. For site to site traffic, this is fine, we just static route the public IPs and remote networks out of the BDSL line. The policy based routing works fine for any internal traffic that matches an ACL. The problem is now that there are remote VPN sites originating from dynamic addresses, so we cannot use static routes. The replies to incoming ISAKMP requests are following the default route out of the ADSL (despite there being no crypto map on that interface). I want to route the outgoing VPN traffic out of the BDSL. I have tried adding udp/500 and esp to and from the route-map acl that pushes traffic out of the BDSL line, but it doesn't match, presumably because the route-map happen earlier than the IPSec stuff. Any ideas how I can do this? IOS ver: 12.4.13T.

    Read the article

  • Multi Gateway and Backup Routing on a cisco router

    - by user64880
    Hi all, I have a 2611 Cisco Router with only one Fastethernet port Now I have two internet gateways. I want to config my router as when primary routing fails second routing automatically start to route all my packets. When I set 2 IP route command in my router then I check I see it work well but when peer IP on primary routing is down it can not change to second routing until I remove first route command.In the following I write my setting. How can I set it? interface FastEthernet0/0 ip address 81.12.21.100 255.255.255.248 secondary ip address 62.220.97.14 255.255.255.252 ip route 0.0.0.0 0.0.0.0 62.220.97.13 ip route 0.0.0.0 0.0.0.0 81.12.21.97 100 Cheer, Kamal

    Read the article

  • Why can one null return be tested but another throws an exception?

    - by mickey
    I want to test if an xml attribute is present. Given this: XmlAttributeCollection PG_attrColl = SomeNodeorAnother.Attributes; This first test works: if (null != PG_attrColl["SomeAttribute"]) "GetNamedItem" is supposed to return null, but the following test throws an exception complaining about the null it returns. if (null != PG_attrColl.GetNamedItem("SomeAttribute").Value;) Why the difference? Just curious.

    Read the article

  • How to add Exception to route with :any in CodeIgniter?

    - by aslamdoctor
    In my project, have setup an admin panel under a folder inside controllers folder like this controllers/admin_panel/dashboard.php And when we open it like this, it loads dashboard controller default http://www.mysite.com/admin_panel Now I have added a page controller on root level to load the page content from database. So here I have some a setup of kind of CMS. To load the page controller, I have added a condition in routes as below $route[':any'] = "page"; But what it is doing now is, when I try to open admin_panel, it loads the page controller. So I want to add a kind of exception condition here like route any except admin_panel Any suggestions how can I achieve this ? Thanks in advance.

    Read the article

  • Why doesn't a URL with two hyphens ( in one segment ) match a Route in my Route Table?

    - by Atomiton
    I'm trying to resolve this URL Route: Route articlesByCategory = new Route("articles/c{cid}-{category}", new Handler); However, it seems like the following url won't resolve to this route: // doesn't work www.site.com/articles/c24-this-is-the-category-title // This works www.site.com/articles/c24-category I assume it has to do with the dashes in the title, but can anyone tell me why this works this way? Is there a way to allow dashes in the title for a URL route like this?

    Read the article

  • Best way to check for null values in Java?

    - by Arty-fishL
    I need to check whether the function of an object returns true or false in Java, but that object may be null, so obviously then the function would throw a NullPointerException. This means I need to check if the object is null before checking the value of the function. What is the best way to go about this? I've listed some methods I considered, I just want to know the most sensible one, the one that is best programming practice for Java (opinion?). // method 1 if (foo != null) { if (foo.bar()) { etc... } } // method 2 if (foo != null ? foo.bar() : false) { etc... } // method 3 try { if (foo.bar()) { etc... } } catch (NullPointerException e) { } // method 4 // would this work all the time, would it still call foo.bar()? if (foo != null && foo.bar()) { etc... }

    Read the article

  • Routing data through VPN in linux

    - by Shadyabhi
    I think its a silly question but still here it goes.. Terminal Output: eth0 Link encap:Ethernet HWaddr 00:1c:c0:37:5e:25 inet addr:10.100.98.51 Bcast:10.100.98.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe37:5e25/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:29677 errors:0 dropped:0 overruns:0 frame:0 TX packets:5209 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3179007 (3.1 MB) TX bytes:610142 (610.1 KB) Memory:e0380000-e03a0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9555 (9.5 KB) TX bytes:9555 (9.5 KB) vpn_0 Link encap:Ethernet HWaddr 00:ac:39:95:a1:16 inet6 addr: fe80::2ac:39ff:fe95:a116/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1786 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:128597 (128.5 KB) TX bytes:468 (468.0 B) Actually, I followed this tutorial to setup the PacketiX VPN on ubuntu. Now, how do I actually use this VPN? Terminal Output: shadyabhi@shadyabhi-desktop:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 shadyabhi@shadyabhi-desktop:~$ As told in tutorial, if I do route del default route add default dev vpn_0 I am not able to surf the internet. And I get the route command output as: root@shadyabhi-desktop:/home/shadyabhi# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default * 0.0.0.0 U 0 0 0 vpn_0 root@shadyabhi-desktop:/home/shadyabhi# I know I am not able to route the traffic properly. How do i do that?

    Read the article

  • How to fake ip at localhost without LoopBack.

    - by sexer
    How can i fake an ip on my own PC? for example if there were an ip address lets say 201.91.81.71, that Host is somewhere outside of my red and is hosting a webserver. How can set a website on my own PC, and when i go to browser and try to explore 201.91.81.71 it actually explore the website at my own PC? pd: I need it with IP addresses not domain names, since I need to implement it on a non-web service. First guess was installing a LoopBack with 201.191.81.71 as ip, but since some times the subnet works and some other it doesn't isn't a stable solution. Second guess was adding a route to route table : route add 201.91.81.71 mask 255.255.255.255 192.168.1.2 192.168.1.2 is the ip address of my NIC. If i could add this route it would work but windows doesn't let me do so. route add 201.91.81.71 mask 255.255.255.255 127.0.0.1 it doesn't let me set as gateway 127.0.0.1 if 201.91.81.71 isn't set in a NIC, so thats why i set sometimes loopback and this route add is auto, but it needs a subnet mask which doesn't match the ip and cannot set 255.255.255.255, im in real throubles here. can i get some help? thx.

    Read the article

  • Routing table on Linux not respected

    - by MRHaarmann
    I have a very specific problem, building a Linux VPN endpoint (with external VPN Gateway), which should route certain networks over the tunnel, others via default gateway. The Linux VPN should do a NAT on the outgoing connections for the VPN peers. Setup is as following: Internet gateway LAN 192.168.25.1/24 VPN Gateway LAN 10.45.99.2/24 (VPN tunnel 10.45.99.1 to net 87.115.17.40/29, separate connection to Internet) Linux VPN Router eth0 192.168.25.71/24 eth0:503 10.45.99.1/24 Default 192.168.25.1 route to 87.115.17.40/29 via 10.45.99.2 (send_redirects disabled, ip_forward enabled) Linux clients (multiple): eth0 192.168.25.x/24 Default 192.168.25.1 route to 87.115.17.40/29 via 192.168.25.71 Ping to the machines via tunnel from the VPN Router is working. Now I want to establish a routing from my clients over the VPN gateway and the client packet gets routed to 192.168.25.1 ! traceroute output shows the packets get routed to 192.168.25.71, but then to 192.168.25.1. So the route is not respected in forward ! IPTables and Routing: ip route show 87.115.17.40/29 via 10.45.99.2 dev eth0 10.45.99.0/24 dev eth0 proto kernel scope link src 10.45.99.1 192.168.25.0/24 dev eth0 proto kernel scope link src 192.168.25.71 default via 192.168.25.1 dev eth0 iptables -A INPUT -i eth0:503 -j REJECT iptables -t nat -A POSTROUTING -o eth0:503 -j MASQUERADE iptables -A FORWARD -i eth0:503 -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 192.168.25.0/24 -o eth0:503 -j ACCEPT So what is wrong with my setup ? The route is chosen correctly from localhost, but all the clients get forwarded to the Internet GW. thanks for helping, Marcus

    Read the article

  • How to list all duplicated rows which may include NULL columns?

    - by Yousui
    Hi guys, I have a problem of listing duplicated rows that include NULL columns. Lemme show my problem first. USE [tempdb]; GO IF OBJECT_ID(N'dbo.t') IS NOT NULL BEGIN DROP TABLE dbo.t END GO CREATE TABLE dbo.t ( a NVARCHAR(8), b NVARCHAR(8) ); GO INSERT t VALUES ('a', 'b'); INSERT t VALUES ('a', 'b'); INSERT t VALUES ('a', 'b'); INSERT t VALUES ('c', 'd'); INSERT t VALUES ('c', 'd'); INSERT t VALUES ('c', 'd'); INSERT t VALUES ('c', 'd'); INSERT t VALUES ('e', NULL); INSERT t VALUES (NULL, NULL); INSERT t VALUES (NULL, NULL); INSERT t VALUES (NULL, NULL); INSERT t VALUES (NULL, NULL); GO Now I want to show all rows that have other rows duplicated with them, I use the following query. SELECT a, b FROM dbo.t GROUP BY a, b HAVING count(*) > 1 which will give us the result: a b -------- -------- NULL NULL a b c d Now if I want to list all rows that make contribution to duplication, I use this query: WITH duplicate (a, b) AS ( SELECT a, b FROM dbo.t GROUP BY a, b HAVING count(*) > 1 ) SELECT dbo.t.a, dbo.t.b FROM dbo.t INNER JOIN duplicate ON (dbo.t.a = duplicate.a AND dbo.t.b = duplicate.b) Which will give me the result: a b -------- -------- a b a b a b c d c d c d c d As you can see, all rows include NULLs are filtered. The reason I thought is that I use equal sign to test the condition(dbo.t.a = duplicate.a AND dbo.t.b = duplicate.b), and NULLs cannot be compared use equal sign. So, in order to include rows that include NULLs in it in the last result, I have change the aforementioned query to WITH duplicate (a, b) AS ( SELECT a, b FROM dbo.t GROUP BY a, b HAVING count(*) > 1 ) SELECT dbo.t.a, dbo.t.b FROM dbo.t INNER JOIN duplicate ON (dbo.t.a = duplicate.a AND dbo.t.b = duplicate.b) OR (dbo.t.a IS NULL AND duplicate.a IS NULL AND dbo.t.b = duplicate.b) OR (dbo.t.b IS NULL AND duplicate.b IS NULL AND dbo.t.a = duplicate.a) OR (dbo.t.a IS NULL AND duplicate.a IS NULL AND dbo.t.b IS NULL AND duplicate.b IS NULL) And this query will give me the answer as I wanted: a b -------- -------- NULL NULL NULL NULL NULL NULL NULL NULL a b a b a b c d c d c d c d Now my question is, as you can see, this query just include two columns, in order to include NULLs in the last result, you have to use many condition testing statements in the query. As the column number increasing, the condition testing statements you need in your query is increasing astonishingly. How can I solve this problem? Great thanks.

    Read the article

  • How to order by column with non-null values first in sql

    - by devlife
    I need to write a sql statement to select all users ordered by lastname, firstname. This is the part I know how to do :) What I don't know how to do is to order by non-null values first. Right now I get this: null, null null, null p1Last, p1First p2Last, p2First etc I need to get: p1Last, p1First p2Last, p2First null, null null, null Any thoughts?

    Read the article

  • Problem in Saving Multi Level Models in YII

    - by Waqar
    My Table structure for user and his adress detail is as follows CREATE TABLE tbl_users ( id bigint(20) unsigned NOT NULL AUTO_INCREMENT, loginname varchar(128) NOT NULL, enabled enum("True","False"), approved enum("True","False"), password varchar(128) NOT NULL, email varchar(128) NOT NULL, role_id int(20) NOT NULL DEFAULT '2', name varchar(70) NOT NULL, co_type enum("S/O","D/O","W/O") DEFAULT "S/O", co_name varchar(70), gender enum("MALE","FEMALE","OTHER") DEFAULT "MALE", dob date DEFAULT NULL, maritalstatus enum("SINGLE","MARRIED","DIVORCED","WIDOWER") DEFAULT "MARRIED", occupation varchar(100) DEFAULT NULL, occupationtype_id int(20) DEFAULT NULL, occupationindustry_id int(20) DEFAULT NULL, contact_id bigint(20) unsigned DEFAULT NULL, signupreason varchar(500), PRIMARY KEY (id), UNIQUE KEY loginname (loginname), UNIQUE KEY email (email), FOREIGN KEY (role_id) REFERENCES tbl_roles (id), FOREIGN KEY (occupationtype_id) REFERENCES tbl_occupationtypes (id), FOREIGN KEY (occupationindustry_id) REFERENCES tbl_occupationindustries (id), FOREIGN KEY (contact_id) REFERENCES tbl_contacts (id) ) ENGINE=InnoDB; CREATE TABLE tbl_contacts ( id bigint(20) unsigned NOT NULL AUTO_INCREMENT, contact_type enum("cres","pres","coff"), address varchar(300) DEFAULT NULL, landmark varchar(100) DEFAULT NULL, district_id int(11) DEFAULT NULL, city_id int(20) DEFAULT NULL, state_id int(20) DEFAULT NULL, pin_id bigint(20) unsigned DEFAULT NULL, area_id bigint(20) unsigned DEFAULT NULL, po_id bigint(20) unsigned DEFAULT NULL, phone1 varchar(20) DEFAULT NULL, phone2 varchar(20) DEFAULT NULL, mobile1 varchar(20) DEFAULT NULL, mobile2 varchar(20) DEFAULT NULL, PRIMARY KEY (id), FOREIGN KEY (district_id) REFERENCES tbl_districts (id), FOREIGN KEY (city_id) REFERENCES tbl_cities (id), FOREIGN KEY (state_id) REFERENCES tbl_states (id) ) ENGINE=InnoDB; CREATE TABLE tbl_states ( id int(20) NOT NULL AUTO_INCREMENT, name varchar(70) DEFAULT NULL, PRIMARY KEY (id) ) ENGINE=InnoDB; CREATE TABLE tbl_districts ( id int(20) NOT NULL AUTO_INCREMENT, name varchar(70) DEFAULT NULL, state_id int(20) DEFAULT NULL, PRIMARY KEY (id), FOREIGN KEY (state_id) REFERENCES tbl_states (id) ) ENGINE=InnoDB; CREATE TABLE tbl_cities ( id int(20) NOT NULL AUTO_INCREMENT, name varchar(70) DEFAULT NULL, district_id int(20) DEFAULT NULL, state_id int(20) DEFAULT NULL, PRIMARY KEY (id), FOREIGN KEY (district_id) REFERENCES tbl_districts (id), FOREIGN KEY (state_id) REFERENCES tbl_states (id) ) ENGINE=InnoDB; The relationship is as follows User has multiple contacts i.e Permanent Address, Current Address, Office Address. Each Contact has state and City. User-Contact-state like this How to save models of this structure in one go. Please provide a reply ASAP

    Read the article

  • executing null values records

    - by jjj
    i am trying to execute the records that have TotalTime null value from the table NewTimeAttendance...TotalTime datatype nchar(10) select * from newtimeattendance where TotalTime = 'NULL' ....nothing select * from newtimeattendance where TotalTime = 'null' ....nothing select * from newtimeattendance where TotalTime = 'Null' ....nothing select * from newtimeattendance where TotalTime = null ....nothing select * from newtimeattendance where TotalTime = Null ....nothing select * from newtimeattendance where TotalTime = NULL ....nothing when i select the whole table i can see that there is some NULL TotalTime values..!! it is small select statment ..why doesn't it work ? is there a way (special way ) to execute the 'NULL' with nchar type ?! thanks in advance

    Read the article

  • MiniMax function throws null pointer exception

    - by Sven
    I'm working on a school project, I have to build a tic tac toe game with the AI based on the MiniMax algorithm. The two player mode works like it should. I followed the code example on http://ethangunderson.com/blog/minimax-algorithm-in-c/. The only thing is that I get a NullPointer Exception when I run the code. And I can't wrap my finger around it. I placed a comment in the code where the exception is thrown. The recursive call is returning a null pointer, what is very strange because it can't.. When I place a breakpoint on the null return with the help of a if statement, then I see that there ARE still 2 to 3 empty places.. I probably overlooking something. Hope someone can tell me what I'm doing wrong. Here is the MiniMax code (the tic tac toe code is not important): /* * To change this template, choose Tools | Templates * and open the template in the editor. */ package MiniMax; import Game.Block; import Game.Board; import java.util.ArrayList; public class MiniMax { public static Place getBestMove(Board gameBoard, Block.TYPE player) { Place bestPlace = null; ArrayList<Place> emptyPlaces = gameBoard.getEmptyPlaces(); Board newBoard; //loop trough all the empty places for(Place emptyPlace : emptyPlaces) { newBoard = gameBoard.clone(); newBoard.setBlock(emptyPlace.getRow(), emptyPlace.getCell(), player); //no game won and still room to move if(newBoard.getWinner() == Block.TYPE.NONE && newBoard.getEmptyPlaces().size() > 0) { //is an node (has children) Place tempPlace = getBestMove(newBoard, invertPlayer(player)); //ERROR is thrown here! tempPlace is null. emptyPlace.setScore(tempPlace.getScore()); } else { //is an leaf if(newBoard.getWinner() == Block.TYPE.NONE) { emptyPlace.setScore(0); } else if(newBoard.getWinner() == Block.TYPE.X) { emptyPlace.setScore(-1); } else if(newBoard.getWinner() == Block.TYPE.O) { emptyPlace.setScore(1); } //if this move is better then our prev move, take it! if((bestPlace == null) || (player == Block.TYPE.X && emptyPlace.getScore() < bestPlace.getScore()) || (player == Block.TYPE.O && emptyPlace.getScore() > bestPlace.getScore())) { bestPlace = emptyPlace; } } } //This should never be null, but it does.. return bestPlace; } private static Block.TYPE invertPlayer(Block.TYPE player) { if(player == Block.TYPE.X) { return Block.TYPE.O; } return Block.TYPE.X; } }

    Read the article

  • SQL: empty string vs NULL value

    - by Jacek Prucia
    I know this subject is a bit controversial and there are a lot of various articles/opinions floating around the internet. Unfortunatelly, most of them assume the person doesn't know what the difference between NULL and empty string is. So they tell stories about surprising results with joins/aggregates and generally do a bit more advanced SQL lessons. By doing this, they absolutely miss the whole point and are therefore useless for me. So hopefully this question and all answers will move subject a bit forward. Let's suppose I have a table with personal information (name, birth, etc) where one of the columns is an email address with varchar type. We assume that for some reason some people might not want to provide an email address. When inserting such data (without email) into the table, there are two available choices: set cell to NULL or set it to empty string (''). Let's assume that I'm aware of all the technical implications of choosing one solution over another and I can create correct SQL queries for either scenario. The problem is even when both values differ on the technical level, they are exactly the same on logical level. After looking at NULL and '' I came to a single conclusion: I don't know email address of the guy. Also no matter how hard i tried, I was not able to sent an e-mail using either NULL or empty string, so apparently most SMTP servers out there agree with my logic. So i tend to use NULL where i don't know the value and consider empty string a bad thing. After some intense discussions with colleagues i came with two questions: am I right in assuming that using empty string for an unknown value is causing a database to "lie" about the facts? To be more precise: using SQL's idea of what is value and what is not, I might come to conclusion: we have e-mail address, just by finding out it is not null. But then later on, when trying to send e-mail I'll come to contradictory conclusion: no, we don't have e-mail address, that @!#$ Database must have been lying! Is there any logical scenario in which an empty string '' could be such a good carrier of important information (besides value and no value), which would be troublesome/inefficient to store by any other way (like additional column). I've seen many posts claiming that sometimes it's good to use empty string along with real values and NULLs, but so far haven't seen a scenario that would be logical (in terms of SQL/DB design). P.S. Some people will be tempted to answer, that it is just a matter of personal taste. I don't agree. To me it is a design decision with important consequences. So i'd like to see answers where opion about this is backed by some logical and/or technical reasons.

    Read the article

  • Route URL laravel 4

    - by nabil l.
    How can I do this in Laravel 4 URL::route('auth.reset', array('kh34KHh4K342')) Instead of http://domain.tld/auth/reset?kh34KHh4K342 I want to get this : http://domain.tld/auth/reset/kh34KHh4K342 EDIT This my routes.php : The problem is because I have two routes with the same name? How do you explain that ? Should i set a different name event is the same kind, and different methods // Set locale $locale = Request::segment(1); if(in_array($locale, Config::get('app.languages'))) { \App::setLocale($locale); } else { $locale = null; } Route::group( array( 'prefix' => $locale ), function () { Route::get('/'), array( 'uses' => 'HomeController@getIndex', 'as' => '/' )); // Auth Route::group( array( 'prefix' => 'auth' ), function () { // Login Route::get( 'login', array( 'before' => 'guest', 'uses' => 'UserController@getLogin', 'as' => 'auth.login' ) ); Route::post( 'login', array( 'before' => 'guest|csrf', 'uses' => 'UserController@postLogin', 'as' => 'auth.login' ) ); Route::get( 'reset/{$token}', array( 'uses' => 'UserController@getReset', 'as' => 'auth.reset' ) ); Route::post( 'reset', array( 'uses' => 'UserController@postReset', 'as' => 'auth.reset' ) ); } );

    Read the article

  • Problem with SQL syntax (probably simple)

    - by Bryan Folds
    I'm doing some custom database work for a module for Drupal and I get the following SQL error when trying to create my table: user warning: You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'DEFAULT NULL, rooms INT DEFAULT NULL, adults INT DEFAULT NULL, children' at line 14 query: CREATE TABLE dr_enquiry ( eId INT unsigned NOT NULL auto_increment, eKey VARCHAR(16) NOT NULL, dateSent INT NOT NULL DEFAULT 0, status VARCHAR(30) NOT NULL DEFAULT 'Unanswered', custName VARCHAR(50) NOT NULL, custEmail VARCHAR(200) NOT NULL, custPhone VARCHAR(25) NOT NULL, custCountry VARCHAR(40) NOT NULL, custIP VARCHAR(11) DEFAULT NULL, offerName VARCHAR(100) NOT NULL, offerURL VARCHAR(200) NOT NULL, arrival DATETIME DEFAULT NULL, departure DEFAULT NULL, rooms INT DEFAULT NULL, adults INT DEFAULT NULL, children INT DEFAULT NULL, childAges VARCHAR(32) DEFAULT NULL, toddlers INT DEFAULT NULL, toddlerAges VARCHAR(32) DEFAULT NULL, catering VARCHAR(255) DEFAULT NULL, comments VARCHAR(255) DEFAULT NULL, agent VARCHAR(100) DEFAULT NULL, voucher VARCHAR(100) DEFAULT NULL, PRIMARY KEY (eId) ) /*!40100 DEFAULT CHARACTER SET UTF8 */ in /home/travelco/public_html/includes/database.inc on line 550.

    Read the article

  • tomcat5 HTTP 400 BAd Request

    - by Oneiroi
    OS is centOS 5.5 x64, rpm's are as follows: tomcat5-jsp-2.0-api-5.5.23-0jpp.9.el5_5 tomcat5-common-lib-5.5.23-0jpp.9.el5_5 tomcat5-servlet-2.4-api-5.5.23-0jpp.9.el5_5 tomcat5-server-lib-5.5.23-0jpp.9.el5_5 tomcat5-5.5.23-0jpp.9.el5_5 tomcat5-jasper-5.5.23-0jpp.9.el5_5 telnet localhost 8080 Trying 127.0.0.1... Connected to localhost.localdomain (127.0.0.1). Escape character is '^]'. GET / HTTP/1.0 Host: localhost HTTP/1.1 400 Bad Request Server: Apache-Coyote/1.1 Date: Thu, 16 Sep 2010 15:06:21 GMT Connection: close alternatives --display java output: alternatives --display java java - status is manual. link currently points to /usr/lib/jvm/jre1.6.0_21/bin/java /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/java - priority 16000 slave keytool: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/keytool slave orbd: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/orbd slave pack200: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/pack200 slave rmid: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/rmid slave rmiregistry: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/rmiregistry slave servertool: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/servertool slave tnameserv: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/tnameserv slave unpack200: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/unpack200 slave jre_exports: /usr/lib/jvm-exports/jre-1.6.0-openjdk.x86_64 slave jre: /usr/lib/jvm/jre-1.6.0-openjdk.x86_64 slave java.1.gz: /usr/share/man/man1/java-java-1.6.0-openjdk.1.gz slave keytool.1.gz: /usr/share/man/man1/keytool-java-1.6.0-openjdk.1.gz slave orbd.1.gz: /usr/share/man/man1/orbd-java-1.6.0-openjdk.1.gz slave pack200.1.gz: /usr/share/man/man1/pack200-java-1.6.0-openjdk.1.gz slave rmid.1.gz: /usr/share/man/man1/rmid-java-1.6.0-openjdk.1.gz slave rmiregistry.1.gz: /usr/share/man/man1/rmiregistry-java-1.6.0-openjdk.1.gz slave servertool.1.gz: /usr/share/man/man1/servertool-java-1.6.0-openjdk.1.gz slave tnameserv.1.gz: /usr/share/man/man1/tnameserv-java-1.6.0-openjdk.1.gz slave unpack200.1.gz: /usr/share/man/man1/unpack200-java-1.6.0-openjdk.1.gz /usr/lib/jvm/jre-1.4.2-gcj/bin/java - priority 1420 slave keytool: /usr/lib/jvm/jre-1.4.2-gcj/bin/keytool slave orbd: (null) slave pack200: (null) slave rmid: (null) slave rmiregistry: /usr/lib/jvm/jre-1.4.2-gcj/bin/rmiregistry slave servertool: (null) slave tnameserv: (null) slave unpack200: (null) slave jre_exports: /usr/lib/jvm-exports/jre-1.4.2-gcj slave jre: /usr/lib/jvm/jre-1.4.2-gcj slave java.1.gz: (null) slave keytool.1.gz: (null) slave orbd.1.gz: (null) slave pack200.1.gz: (null) slave rmid.1.gz: (null) slave rmiregistry.1.gz: (null) slave servertool.1.gz: (null) slave tnameserv.1.gz: (null) slave unpack200.1.gz: (null) /usr/lib/jvm/jre1.6.0_21/bin/java - priority 2 slave keytool: (null) slave orbd: (null) slave pack200: (null) slave rmid: (null) slave rmiregistry: (null) slave servertool: (null) slave tnameserv: (null) slave unpack200: (null) slave jre_exports: (null) slave jre: (null) slave java.1.gz: (null) slave keytool.1.gz: (null) slave orbd.1.gz: (null) slave pack200.1.gz: (null) slave rmid.1.gz: (null) slave rmiregistry.1.gz: (null) slave servertool.1.gz: (null) slave tnameserv.1.gz: (null) slave unpack200.1.gz: (null) Current `best' version is /usr/lib/jvm/jre-1.6.0-openjdk.x86_64/bin/java. Same occurs trying HTTP/1.1, and I am at a complete loss as to why.

    Read the article

  • Add logo background color to data returned by StackAuth sites route

    - by Yi Jiang
    Given that now with Stack Exchange 2.0 the logo of some of the sites, like Web Apps, AskUbuntu, Photography, Gaming and Pro Webmasters have non-white background, I think it will be best if the StackAuth sites route can include the preferred background color for those the logo of these sites. This is especially important for sites like Photography whose logo is unreadable if the traditional white is used. Edit: Here's an example of what I mean here: As you can see, the AskUbuntu logo text totally invisible against a white background.

    Read the article

  • Trying to import SQL file in a xampp server returns error

    - by Victor_J_Martin
    I have done a ER diagram in Mysql Workbench, and I am trying load in my server with phpMyAdmin, but it returns me the next error: Error SQL Query: -- ----------------------------------------------------- -- Table `BDA`.`UG` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`UG` ( `numero_ug` INT NOT NULL, `nombre` VARCHAR(45) NOT NULL, `segunda_firma_autorizada` VARCHAR(45) NOT NULL, `fecha_creacion` DATE NOT NULL, `nombre_depto` VARCHAR(140) NOT NULL, `dni` INT NOT NULL, `anho_contable` INT NOT NULL, PRIMARY KEY (`numero_ug`), INDEX `nombre_depto_idx` (`nombre_depto` ASC), INDEX `dni_idx` (`dni` ASC), INDEX `anho_contable_idx` (`anho_contable` ASC), CONSTRAINT `nombre_depto` FOREIGN KEY (`nombre_depto`) REFERENCES `BDA`.`Departamento` (`nombre_depto`) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `dni` FOREIGN KEY (`dni`) REFERENCES `BDA`.`Trabajador` (`dni`) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `anho_contable` FOREIGN KEY (`anho_contable`) REFERENCES `BDA`.`Capitulo_Contable` (`anho_contable`) [...] MySQL said: Documentation #1022 - Can't write; duplicate key in table 'ug' I export the result of the diagram from Mysql Workbench to a SQL file, and this file is what I'm trying to upload. This is the file. I can not find the duplicate key. SET @OLD_UNIQUE_CHECKS=@@UNIQUE_CHECKS, UNIQUE_CHECKS=0; SET @OLD_FOREIGN_KEY_CHECKS=@@FOREIGN_KEY_CHECKS, FOREIGN_KEY_CHECKS=0; SET @OLD_SQL_MODE=@@SQL_MODE, SQL_MODE='TRADITIONAL,ALLOW_INVALID_DATES'; CREATE SCHEMA IF NOT EXISTS `BDA` DEFAULT CHARACTER SET utf8 COLLATE utf8_general_ci ; USE `BDA` ; -- ----------------------------------------------------- -- Table `BDA`.`Departamento` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Departamento` ( `nombre_depto` VARCHAR(140) NOT NULL, `area_depto` VARCHAR(140) NOT NULL, PRIMARY KEY (`nombre_depto`)) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`Trabajador` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Trabajador` ( `dni` INT NOT NULL, `direccion` VARCHAR(140) NOT NULL, `nombre` VARCHAR(45) NOT NULL, `apellidos` VARCHAR(140) NOT NULL, `fecha_nacimiento` DATE NOT NULL, `fecha_contrato` DATE NOT NULL, `titulacion` VARCHAR(140) NULL, `nombre_depto` VARCHAR(45) NOT NULL, PRIMARY KEY (`dni`), INDEX `nombre_depto_idx` (`nombre_depto` ASC), CONSTRAINT `nombre_depto` FOREIGN KEY (`nombre_depto`) REFERENCES `BDA`.`Departamento` (`nombre_depto`) ON DELETE NO ACTION ON UPDATE NO ACTION) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`Capitulo_Contable` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Capitulo_Contable` ( `anho_contable` INT NOT NULL, `numero_ug` INT NOT NULL, `debe` DOUBLE NOT NULL, `haber` DOUBLE NOT NULL, PRIMARY KEY (`anho_contable`), INDEX `numero_ug_idx` (`numero_ug` ASC), CONSTRAINT `numero_ug` FOREIGN KEY (`numero_ug`) REFERENCES `BDA`.`UG` (`numero_ug`) ON DELETE NO ACTION ON UPDATE NO ACTION) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`UG` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`UG` ( `numero_ug` INT NOT NULL, `nombre` VARCHAR(45) NOT NULL, `segunda_firma_autorizada` VARCHAR(45) NOT NULL, `fecha_creacion` DATE NOT NULL, `nombre_depto` VARCHAR(140) NOT NULL, `dni` INT NOT NULL, `anho_contable` INT NOT NULL, PRIMARY KEY (`numero_ug`), INDEX `nombre_depto_idx` (`nombre_depto` ASC), INDEX `dni_idx` (`dni` ASC), INDEX `anho_contable_idx` (`anho_contable` ASC), CONSTRAINT `nombre_depto` FOREIGN KEY (`nombre_depto`) REFERENCES `BDA`.`Departamento` (`nombre_depto`) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `dni` FOREIGN KEY (`dni`) REFERENCES `BDA`.`Trabajador` (`dni`) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `anho_contable` FOREIGN KEY (`anho_contable`) REFERENCES `BDA`.`Capitulo_Contable` (`anho_contable`) ON DELETE NO ACTION ON UPDATE NO ACTION) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`Cliente` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Cliente` ( `cif_cliente` INT NOT NULL, `nombre_cliente` VARCHAR(140) NOT NULL, PRIMARY KEY (`cif_cliente`)) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`Ingreso` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Ingreso` ( `id` INT NOT NULL, `concepto` VARCHAR(45) NOT NULL, `importe` DOUBLE NOT NULL, `fecha` DATE NOT NULL, `cif_cliente` INT NOT NULL, `numero_ug` INT NOT NULL, PRIMARY KEY (`id`), INDEX `cif_cliente_idx` (`cif_cliente` ASC), INDEX `numero_ug_idx` (`numero_ug` ASC), CONSTRAINT `cif_cliente` FOREIGN KEY (`cif_cliente`) REFERENCES `BDA`.`Cliente` (`cif_cliente`) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `numero_ug` FOREIGN KEY (`numero_ug`) REFERENCES `BDA`.`UG` (`numero_ug`) ON DELETE NO ACTION ON UPDATE NO ACTION) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`Proveedor` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Proveedor` ( `cif_proveedor` INT NOT NULL, `nombre_proveedor` VARCHAR(140) NOT NULL, PRIMARY KEY (`cif_proveedor`)) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `BDA`.`Gasto` -- ----------------------------------------------------- CREATE TABLE IF NOT EXISTS `BDA`.`Gasto` ( `id` INT NOT NULL, `concepto` VARCHAR(45) NOT NULL, `importe` DOUBLE NOT NULL, `fecha` DATE NOT NULL, `factura` INT NOT NULL, `cif_proveedor` INT NOT NULL, `numero_ug` INT NOT NULL, PRIMARY KEY (`id`), INDEX `cif_proveedor_idx` (`cif_proveedor` ASC), INDEX `numero_ug_idx` (`numero_ug` ASC), CONSTRAINT `cif_proveedor` FOREIGN KEY (`cif_proveedor`) REFERENCES `BDA`.`Proveedor` (`cif_proveedor`) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `numero_ug` FOREIGN KEY (`numero_ug`) REFERENCES `BDA`.`UG` (`numero_ug`) ON DELETE NO ACTION ON UPDATE NO ACTION) ENGINE = InnoDB; SET SQL_MODE=@OLD_SQL_MODE; SET FOREIGN_KEY_CHECKS=@OLD_FOREIGN_KEY_CHECKS; SET UNIQUE_CHECKS=@OLD_UNIQUE_CHECKS; Thanks for your advices.

    Read the article

  • route lan traffic through wirless mifi

    - by Randall Blake
    I have a Windows 7 laptop accessing the internet through Verizon wireless MIFI configured as 192.168.1.1. It supports only 5 wireless connections, so I don't want to use up connections unnecessarily. That laptop has an ethernet nic which I have given a static IP of 192.168.0.5. Everything else on the 192.168.0.0 network acquires an address via DHCP from a DLink router whose address is 192.168.0.1. Also on that network are a printer, some network cameras, and a linux pc. The linux pc does not have a wireless card (and I don't want to buy one). The linux pc is located at 192.168.0.122. I can ping the linux pc from the windows pc. But I cannot access the internet from the linux pc. I can ping everything on the 192.168.0.0 network EXCEPT the ethernet card in the Windows PC. It seems as though my DLink router will not route requests to the 192.168.0.5 nic on the windows pc. My windows pc has a default route pointing to the 192.168.1.0 network. It also has a route telling it to route all traffic destined for the 192.168.0.0 network through the 192.168.0.5 interface. I have tried adding a default route to the linux pc to "gateway" 192.168.0.5, but that does not work. I have also tried adding a default route to the linux pc to the gateway 192.168.0.1 (the DLink router) but that will not give me internet access either (over the 192.168.1.0 network). I tried these two different routes at different times - I did not set them both at the same time. I suppose this is a simple problem to solve, but I cannot seem to solve it. How can I give internet access over the 192.168.1.1 MIFI to my linux pc on 192.168.0.122? Thanks EDIT: Additional Info Internet | | MIFI (192.168.1.1) (wireless) | | (192.168.1.3) (wireless) Windows 7 PC Dlink Router (192.168.0.1) ------------ (192.168.0.5) (wired) | | |linux pc (192.168.0.122) (wired) | |printer (192.168.0.100) (wireless) | |network cameras, etc (192.168.0.103) (wireless) Only the windows pc is multi-homed with a wireless nic that connects to the MIFI wirelessly, and an ethernet nic with a wired connection to the DLink router. (The DLink permits both wired and wireless connections.) I don't want to use Windows internet connection sharing because I believe it will set up the ethernet nic as a gateway on 192.168.0.1 and a DHCP server. I already have the Dlink performing that role and I don't want to change that if I do not have to. (The Dlink permits me to make DHCP reservations and I really like that feature. I don't want to lose it.)

    Read the article

  • How to implement List, Set, and Map in null free design?

    - by Pyrolistical
    Its great when you can return a null/empty object in most cases to avoid nulls, but what about Collection like objects? In Java, Map returns null if key in get(key) is not found in the map. The best way I can think of to avoid nulls in this situation is to return an Entry<T> object, which is either the EmptyEntry<T>, or contains the value T. Sure we avoid the null, but now you can have a class cast exception if you don't check if its an EmptyEntry<T>. Is there a better way to avoid nulls in Map's get(K)? And for argument sake, let's say this language don't even have null, so don't say just use nulls.

    Read the article

  • Shorten Zend Framework Route Definitions

    - by Sebastian Hoitz
    Hi! How can I shorten the definition of my custom routes in Zend Framework? I currently have this as definition: $route = new Zend_Controller_Router_Route( ":module/:id", array( "controller" => "index", "action" => "index" ), array("id" => "\d+") ); self::$frontController->getRouter()->addRoute('shortcutOne', $route); $route = new Zend_Controller_Router_Route( ":module/:controller/:id", array("action" => "index"), array("id" => "\d+") ); self::$frontController->getRouter()->addRoute('shortcutTwo', $route); $route = new Zend_Controller_Router_Route( ":module/:controller/:action/:id", null, array("id" => "\d+") ); self::$frontController->getRouter()->addRoute('shortcutThree', $route); Is there a way to better combine these rules? And what are your best practices in where to place these? I currently have them in my bootstrap class right after the Front Controller initialization.

    Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >