Search Results

Search found 516 results on 21 pages for 'suspend'.

Page 13/21 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

• Weird graphical errors in console and on computer shut down

  - by Mark A.

  I am all new to Ubuntu (and Linux in general) and I am experiencing some strange graphic on my screen. Console #1 (ctrl+alt+f1): Exactly the same happens on all the other consoles (2-6), and the consoles don't seem to work. And I see the same when I hibernate or shut down my computer, but not when I suspend it. I was thinking that it may have something to do with the SiS 671 video driver work around that I use? http://ubuntuforums.org/showpost.php?p=11476910&postcount=773 Any ideas how to fix this?

  Read the article

• Hard Disk Spins Down as long as Battery is in Laptop

  - by Brock Dute

  Hi, I just figured out today that as long as the battery is in my laptop, it doesn't matter if it's fully charged while plugged in, Ubuntu always spins down my hard drive. I noticed this because there was a huge difference in speed when I removed the batteries. My settings for power management is basically: on AC power, don't spin down harddrive, dont suspend or anything on battery power, basically save as much power as possible I assumed that if I plug in my laptop, it'll use the On AC Power settings no matter what but apparently, this isn't so. Is there a way to "fix" this?

  Read the article

• Atheros AR2413 wireless not working after shutdown

  - by Chandrasekhar

  I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

  Read the article

• What is the best way to pass data into an API from a website?

  - by Chris Wakoksi

  My main objective is to create a User Interface in order to provision(change the status: activate, deactivate, or suspend) modems. I have received a SOAP developer's guide to the specific type of modem that helps out with the specific values that I need to pass into Iridium's WSDL but I cannot figure out how to do this from a webpage I have created using HTML/CSS, and PHP? I have been told by others that I need to know the portal. I have no idea what that means. I am a beginner programmer who has learned programming for this project. Any suggestions as to how to pass my data into the provisioning API?

  Read the article

• Hide debug information when running apps from the command line

  - by tutuca

  Most of the time running a gtk application from the command line it starts dumping debug information to the stdio even though I put them in background. Example: ~$ gedit test.html # and ctrl+z to suspend zsh: suspended gedit .zshrc ~$ bg [1] + continued gedit .zshrc ~$ # do some editing (gedit:6208): GtkSourceView-WARNING **: Could not find word to remove in buffer (whoosh), this should not happen! (gedit:6208): GtkSourceView-WARNING **: Could not find word to remove in buffer (haystack), this should not happen! I want to note that the error, or warning, changes according to what I'm doing at the moment. The GtkSourceView-WARNING shown here is one of the cases. Anyway... Do you know if it's at all possible to avoid getting that information printed out?

  Read the article

• My ubuntu with unity not loading after last reboot

  - by Abonec

  I have asus u36sd and after last reboot I can't start up my ubuntu 11.10. Usually I suspend my notebook by closing cover but today I reboot it and it not starting up. Booting flowing by normal till to login screen but if I move mouse cursor after that image immediately switch to console (without any error; only normal loading startup processes) and back to login screen. I can type my password and boot continuing loading but after few moment it again switch back to dark console and switch again to login screen. I can load recovery mode but if I try touch my cursor (by mouse or internal notebook touchpad) it again switch back to console and to login screen. But if I use only keyboard it work fine. Where I can see detailed log information about my problem?

  Read the article

• Closing lid freezes laptop

  - by trampster

  Closing the lid on my dell studio 15 which is running ubuntu 10.04 freezes the screen. This is a new problem in ubuntu 10.04 which did not exist in 9.10 I have tried playing with all the settings in System-Preferences-Screensaver but nothing seems to make any difference. (please note the Power Management settings are accessible from here so I have tried those too.) I don't need hibernate or suspend. I just want to be able to close the lid, and then open it and still have a working laptop. Is their a settings somewhere that will make Ubuntu ignore the lid closing?

  Read the article

• Wake up from sleep with GPIO (I2C)

  - by spambas

  My situation: Ubuntu 10.10 running on an atom driven main board the main board has a GPIO chip integrated (F75111 by Fintek). They communicate through I2C(SMBus). We have a driver running that works, we can send outputs and read inputs. Great! We would like to use the I/O interface to suspend (sleep) and wake up again. Sleep is no problem. On an incoming input: run s2both. Ubuntu goes to sleep and prepares a hibernate state, so when the power-cord is unplugged by accident, it will wake from hibernate. But the big question: how to wake on an input if the OS is already sleeping! You can wake from a lot of devices (lan, usb, ring, etc) but I can't find out how to wake from a I2C card. PLEASE HELP!

  Read the article

• Ubuntu desktop and dash problems

  - by user170163

  I am not sure if i have posted it to right place, so if no please don't judge me, I am a newbie. I installed Ubuntu 13.04 and I am happy with it. I have two OS's in dual boot. Ubuntu and Windows 7. in Ubuntu I have 2 problems. The first one is when I suspend my system I cannot resume it again. It sometimes show me the password screen (user names and etc. (sorry i don't know the exact name of it)) and sometimes just a blank screen. what can be the problem? The second one is this: When I hit ALT+F2 it looks like this ( but not always. when I restart the system everything is OK till about 30-40 minutes. and then it looks like this. Please help, I really like Ubuntu but these 2 problems ruin my plans about it. Thanks

  Read the article

• Is it save to configure "Shutdown" on "When laptop lid is closed" ?

  - by Takkat

  To setup a laptop owned by a complete PC novice any settings that may become hard to tackle remotely need to be avoided. The laptop will be administrated via SSH. One thing in my list are problems arising from improper wake-ups from suspend or hibernate as they may also affect network accessibility. This is why I thought setting up power management to "shutdown" on closing the laptop lid could be a good idea. However I am not sure if this is a safe way to do. What problems in addition to software not closing properly (and thus not saving their data) could I be faced if I proceeded as planned?

  Read the article

• HDMI signal interrputs after 10 minutes plugged in a TV

  - by desert_unbound

  Ubuntu 11.10, Dell Inspiron N4050, VLC, Jupiter I'm trying to watch movies through HDMI output on a TV, with VLC, with the notebook unplugged from AC (but with enough battery for 2-3 hours of use), just with TV display (the notebook display stays off) And from 10 to 10 minutes, the TV turns black, and according to the TV, the HDMI cable is unplugged. But using the touchpad makes the screen appear again. In "screen" options, on system settings, i've set the screen to never turn off, and never reduce brightness using battery. In "power" settings, i've set to not suspend when using battery. In Jupiter, i've set (while trying to watch the movie) to work in maximum performance. I'm pretty sure it's not VLC, because i've set it to override power options and screensaver options (and also im not using xscreensaver). Also the movie continues, when the screen is black Maybe there's something that i'm missing? When i plug the HDMI in the notebook, i use jupiter to change the display (using the option "external display only")... maybe is that ?

  Read the article

• How to permanently disable touchpad in 12.04?

  - by Andreas

  I'm looking for a way to permanently disable the touchpad in Ubuntu 12.04 (my computer is a Lenovo Thinkpad Edge on which it isn't possible to disable it in the BIOS). I tried the applications GPointingDeviceSettings and synaptiks 0.8.1 as well as the applets touchpad-indicator and Jupiter. None of these does the trick of disabling the touchpad permanently. Jupiter comes closest - it remembers that I have disabled the touchpad after restart - but when I login after the computer has been in suspend mode, the touchpad is enabled again. Can anyone help me in disabling the touchpad possibly at a lower level so it won't in any way be enabled unless I choose to enable it? I'm totally new to linux so a detailed explanation would be much appreciated ... The links, so far, doesn't address my question. I have no problem turning the touchpad off and making it stay off after reboot but when I login after the computer has been in an altered power mode it's on again. Isn't there a way to permanently disable a device like touchpad?

  Read the article

• 12.04 sound keeps auto-muting when idle

  - by fali

  I just installed 12.04 on an HP8510W. Everything works fine except for one weird behavior which I have noticed. When ever there is no audio playing, the audio mute indicator on the laptop is on. As soon as I start playing a you tube video the mute indicator turns off and I get sound. Here is my pulse audio output which says that the sink is suspended because it is idle: Welcome to PulseAudio! Use "help" for usage information. list-sinks 1 sink(s) available. index: 0 name: <alsa_output.pci-0000_00_1b.0.analog-stereo> driver: <module-alsa-card.c> flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY state: SUSPENDED suspend cause: IDLE I tried running alsamixer, but I don't see the auto-mute option.

  Read the article

• Is it safe to configure "Shutdown" on "When laptop lid is closed" ?

  - by Takkat

  To setup a laptop owned by a complete PC novice any settings that may become hard to tackle remotely need to be avoided. The laptop will be administrated via SSH. One thing in my list are problems arising from improper wake-ups from suspend or hibernate as they may also affect network accessibility. This is why I thought setting up power management to "shutdown" on closing the laptop lid could be a good idea. However I am not sure if this is a safe way to do. What problems in addition to software not closing properly (and thus not saving their data) could I be faced if I proceeded as planned?

  Read the article

• Resuming from hibernation shows a fuzzy "static" screen

  - by Ross

  When I resume from hibernation in Ubuntu 10.10 the screen shows static, very similar to what you see on an analogue TV that hasn't been tuned properly. This also occurs on boot from shut down, but only for a moment after the Plymouth boot screen. The static lasts for at least 5 minutes. An odd thing that happens is that the mouse pointer, as a lighter square of static, becomes visible and you can move it around. Attempting to change into a terminal (i.e. Ctrl+Alt+F1) doesn't seem to work (and I'm not sure if that can be done from the login screen). Resuming from suspend has different issues - vertical lines appearing for a second before appearing to be in terminal mode (blinking cursor) and then going to the lock screen. I'm running Ubuntu 10.10 on a Dell Studio 15 with ATI graphics, however I'm not using the proprietary drivers as I had issues with dual-screen support, so it's the generic X.org drivers being used.

  Read the article

• ASUS EeePC Fn+F2 ruins wireless until restart

  - by dawmail333

  I managed to get my wireless working beautifully (ath5k driver working great), and it works over a disable/enable wireless cycle, even a suspend/wakeup cycle (read some people have issues with that). Unfortunately, I discovered that if I press Fn+F2 on my keyboard (Asus EeePC 900HA, so that's the wireless toggle key), wireless then stops working until I restart the computer. How can I fix this? I'm running UNR 10.10 (with Unity turned off tyvm!). I heard something about Jupiter controlling these keys, but what about asus-laptop? How can I fix this behaviour? TIA. (Note, I'm a power user, but still fairly new to Linux. I'm picking up speed though).

  Read the article

• Cannot resume from hibernate (s2disk)

  - by hwjp

  I seem to be able to hibernate OK using s2disk, but when I switch the laptop back on, it seems to hang half-way through the "resuming" menu. The splash screen looks healthy, it seems to be trying to resume from the correct disk, but it hangs about half-way through, with three little pips. One great help would be - where can I find the logs, and how do I get more verbose ones? There is some info in /var/log/pm-suspend.log, but that all seems fine, just lots of hibernate: success messages... How do I switch on more verbose logging in s2disk? And what about the resume process, where are the logs for that, and how can I make them more detailed? Background: the standard Ubuntu hibernate wouldn't work, so I've install uswusp and its associated tools - s2disk etc. That initially made things worse, but a fair amount of fiddling with its config, my swap size and so on seem to have got it at least seemingly successfully suspending...

  Read the article

• Ubuntu 12.10 64b does not shutdown

  - by user108264

  I am a new linux user so i am not familiar with what actually is needed to check. When shutting down or trying to restart i get a screen with yellow letters and the system does not close or restart. I have to shut down manually. I can't type all the numbers but i will give the last ones. [90102.232650] [ end-trace 435966f5b367871 ] this seems to have happened after i downgraded the xorg so i can get drivers for my ATI card(4850HD). The suspend command works fine.

  Read the article

• Ubuntu 12.04 intermittently fails to wake up from sleep

  - by stacksia

  When I put my Ubuntu 12.04 machine into sleep, sometimes on waking up, it fails, logs me out, and takes me back to login screen. When I log back in, it tells me some unexpected error happened, but it fails to let me report the bug. This has started to happen recently, but I don't know what triggered it. uname -a Linux [name] 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux The issue seems similar to Xorg intermittently restarts after suspend. But in my case I am not sure if it is a Xorg issue. I looked at xorg logs, but didn't notice anything indicating an error. I know I am not providing a lot of info, but I am not sure where (e.g. which log files) I should seek for more info.

  Read the article

• Ubuntu 12.04 terminal only after nvidia driver upgrade

  - by user1613361

  I recently installed Ubuntu 12.04 (after getting tired of Windows). Installation went fine. I had one problem when I got in suspend mode and then resumed my screen was scrambled. After some googling founds some tips to upgrade my nvidia drivers. I did this, and rebooted but only a terminal windows appears now instead of a graphical desktop. Tried to fix it by several reboots, and removing xorg.conf, but still no luck. Any advice how to fix it and get my desktop back ?

  Read the article

• Laptop wakes while lid is closed and overheats

  - by user56601

  I'm running 12.04 on a toshiba L305D with athlon x2 (Already suspect this has something to do with it). My laptop will wake from suspend, presumably from wireless scanning. This is a serious bug as sleeping laptops are often inside bags, so the cooling system is effectively disabled. I can no longer seriously use Ubuntu when I have to worry about hardware damage every time I close the lid. There is shockingly lack of information about anything close to this. So many control panels have been removed or dumbed down, and everyone seems to want this behavior instead of the opposite, for servers or torrents of whatever. Well, most laptop users will 99% be likely to regularly put their laptop in a backpack or briefcase or other bag. Does anyone know how to fix this?

  Read the article

• Screen dims & freezes me out

  - by user287723

  New to Ubuntu 12.04 (used since 8th April). I have recently been using Firefox for an online course and while working on this virtual PC site, the screen dims and I am frozen out of interacting with my desktop. (I cannot switch to any other tabs in Firefox). Power setting set to suspend after 30 mins. The desktop is connected to the mains. Moving the cursor around appears to have no effect. This is making the course difficult to follow so any ideas would be appreciated. Thanks

  Read the article

• Black screen on Ubuntu 12.04

  - by user1648371

  I've just upgraded to Ubuntu 12.04 and I'm experiencing some problems. The first thing I noticed is that when I click the Workspace switcher all I get is a black screen (I can guess where the different workspaces are located and clicked on them, not a practical solution though). In addition when I lock the screen or suspend the laptop (a Vaio VPCEB4M1E) I get a shifted screen (I see the right most vertical stripe on the left size of the monitor and nothing about all the rest, to put it clearly I can see the gear that allows me to turn the pc off, etc, but not much more..) when I go to the additional driver menu I see the "ATI/AMD proprietary FGLRX graphics driver" are installed and the post-release update version is available. I don't know if the problem is driver related, so before doing anything I'd like to get some suggestions from you guys. Thanks you!

  Read the article

• I have ubuntu 11.10 64bit, can't shutdown or restart my pc?

  - by digitalcrow

  I have ubuntu 11.10 64bit, everything worked fine but after i uninstalled the airtime dj app i can't restart or shutdown my pc !! The only way to reach at the screen showing that system is going to shutdown is via terminal but it stucks and never shuts down ! I can't even restart it ! I can suspend my pc fine but can't shutdown or restart it. Need to keep the power button pressed for a long time to shut it down ! Do i have to look for a shutdown script and find out what is happening ?? I'm very unhappy with this it gives to my nerves.

  Read the article

• Gnome 3.10 doesn't show login, Ubuntu 13.10

  - by TheWebs

  I use gnome as default desktop. And I recently upgrade Ubuntu to 13.10 then upgraded gnome to 3.10. Upon restarting, it brings me to the gnome log in screen (GDM) and all I see is the top banner part so like your date, music volume, option to restart, suspend or shutdown. Hitting control+alt+delete tells me gnome display manager will log out - it does but still nothing. I am on the log in screen, but there is no user to select, like there normally is or was. I can boot into safe mode and drop down to shell but I am not sure what commands I would enter to get the login screen back. I am using the gnome PPA's and the "unstable" PPA, so I expected issues, but not this - ideas?

  Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >