Search Results

Search found 488 results on 20 pages for 'xen'.

Page 13/20 | < Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >

  • problem to change my Xenserver password

    - by Michlaou
    I try to change my root password on my Xenserver 6.0. I follow these steps: enter boot: menu.c32 selecet xe-serial and press tab add "single" before the 2nd triple hyphens and i press enter. I have that: mboot.c32 /boot/xen.gz com1=115200,8n1 console=com1, vga mem=1024G dom0_max_vcpus4 dom0_mem=752M lowmem_emergency_pool=1M crashkernel=64M@32M single --- /boot/vmlinuz-2.6-xen root=LABEL=root-rodraxar ro console=tty0 xencons=hvc console=hvc0 --- /boot/initrd-2.6-xen.img I have commande on the screen and it's stop at: ext3-fs: monted filesystem with ordered data mode. Can you help me?

    Read the article

  • linux hardware raid 10 / lvm / virtual machine partition alignment and filesystem optimization

    - by Jason Ward
    I've been reading everything I can find about partition alignment and filesystem optimization (ext4 and xfs) but still don't know enough to be confident in setting up my current configuration. My remaining confusion comes from the LVM layer and if I should use raid parameters on the filesystem in guest os'es. My main questions are: When I use 'pvcreate --dataalignment' do I use the stripe-width as calculated for a filesystem on RAID (128kB for ext4 in my situation), the Stripe size of the RAID set (256kB), something else altogether, or do I not need this? When I create ext2/3/4 or xfs filesystems in guests on the Logical Volumes, should I add the settings for the underlying RAID (e.g. mkfs.ext4 -b 4096 -E stride=64,stripe-width=128)? Does anyone see any glaring errors in my set up below? I'm running some benchmarks now but haven't done enough to start comparing results. I have four drives in RAID 10 on a 3ware 9750-4i controller (more details on the settings below) giving me a 6.0TB device at /dev/sda. Here is my partition table: Model: LSI 9750-4i DISK (scsi) Disk /dev/sda: 5722024MiB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1.00MiB 257MiB 256MiB ext4 BOOTPART boot 2 257MiB 4353MiB 4096MiB linux-swap(v1) 3 4353MiB 266497MiB 262144MiB ext4 4 266497MiB 4460801MiB 4194304MiB Partition 1 is to be the /boot partition for my xen host. Partition 2 is swap. Partition 3 is to be the root (/) for my xen host. Partition 4 is to be (the only) physical volume to be used by LVM (for those who are counting, I left about 1.2TB unallocated for now) For my Xen guests, I usually create a Logical Volume of the needed size and present it to the guests for them to partition as needed. I know there are other ways of handling that but this method works best for my situation. Here's the hardware of interest on my CentOS 6.3 Xen Host: 4x Seagate Barracuda 3TB ST3000DM001 Drives (sector size: 512 logical/4096 physical) 3ware 9750-4i w/BBU (sector size reported: 512 logical/512 physical) All four drives make up a RAID 10 array. Stripe: 256kB Write Cache enabled Read Cache: intelligent StoreSave: Balance Thanks!

    Read the article

  • CodePlex Daily Summary for Thursday, February 24, 2011

    CodePlex Daily Summary for Thursday, February 24, 2011Popular ReleasesInstant Feature Builder for Visual Studio 2010: Instant Feature Builder 1.2: This is the binary version of the Instant Feature Builder. Once downloaded, double click to install into Visual Studio. Version 1.2 fixes: Rename FX to IFB to shorten path lengths Fix issue in ExecuteCommand Fix issue to workaround problem with VS Template writer The Instant Feature Builder is a tool which enables you, via drag-and-drop, to build a specific type of Visual Studio extension (VSIX) known as a Feature Extension. A Feature Extension packages project and/or item templates,...DirectQ: Release 1.8.7 (Beta): Beta release of 1.8.7 to get feedback on what works well, what doesn't work well, and what doesn't work at all. D3D9 hardware with ps2.0 a must. Faster, more streamlined and more integrated rendering capabilities with additional MP features and support.Smartkernel: Smartkernel: ????,??????Chiave File Encryption: Chiave 0.9.1: Application for file encryption and decryption using 512 Bit rijndael encyrption algorithm with simple to use UI. Its written in C# and compiled in .Net version 3.5. It incorporates features of Windows 7 like Jumplists, Taskbar progress and Aero Glass. Change Log from 0.9 Beta to 0.9.1: ======================= >Added option for system shutdown, sleep, hibernate after operation completed. >Minor Changes to the UI. >Numerous Bug fixes. Feedbacks are Welcome!....DotNetNuke® Store: 03.00.00: What's New in this release? IMPORTANT: this version requires DotNetNuke 04.06.02 or higher! DO NOT REPORT BUGS HERE IN THE ISSUE TRACKER, INSTEAD USE THE DotNetNuke Store Forum! This version is the same code base as the version 02.01.51 RC, just some cleaning and source code release before submition to the release tracker for "official" release.ClosedXML - The easy way to OpenXML: ClosedXML 0.45.2: New on this release: 1) Added data validation. See Data Validation 2) Deleting or clearing cells deletes the hyperlinks too. New on v0.45.1 1) Fixed issues 6237, 6240 New on v0.45.2 1) Fixed issues 6257, 6266 New Examples Data ValidationOMEGA CMS: OMEGA CMA - Alpha 0.2: A few fixes for OMEGA Framework (DLL) A few tweeks for OMEGA CMSCoding4Fun Tools: Coding4Fun.Phone.Toolkit v1.2: New control, Toast Prompt! Removed progress bar since Silverlight Toolkit Feb 2010 has it.Umbraco CMS: Umbraco 4.7: Service release fixing 31 issues. A full changelog will be available with the final stable release of 4.7 Important when upgradingUpgrade as if it was a patch release (update /bin, /umbraco and /umbraco_client). For general upgrade information follow the guide found at http://our.umbraco.org/wiki/install-and-setup/upgrading-an-umbraco-installation 4.7 requires the .NET 4.0 framework Web.Config changes Update the web web.config to include the 4 changes found in (they're clearly marked in...HubbleDotNet - Open source full-text search engine: V1.1.0.0: Add Sqlite3 DBAdapter Add App Report when Query Cache is Collecting. Improve the performance of index through Synchronize. Add top 0 feature so that we can only get count of the result. Improve the score calculating algorithm of match. Let the score of the record that match all items large then others. Add MySql DBAdapter Improve performance for multi-fields sort . Using hash table to access the Payload data. The version before used bin search. Using heap sort instead of qui...Xen: Graphics API for XNA: Xen 2.0: This is the final release of Xen; Xen 2.0. Xen 2.0 supports PC and Xbox 360 running XNA 4. The documentation download is coming soon Due to restrictions in XNA 4, Building Xen requires a DirectX 10 capable video card (Xen applications can still run on Windows Xp and DirectX 9 video cards)Silverlight????[???]: silverlight????[???]2.0: ???????,?????,????????silverlight??????。DBSourceTools: DBSourceTools_1.3.0.0: Release 1.3.0.0 Changed editors from FireEdit to ICSharpCode.TextEditor. Complete re-vamp of Intellisense ( further testing needed). Hightlight Field and Table Names in sql scripts. Added field dropdown on all tables and views in DBExplorer. Added data option for viewing data in Tables. Fixed comment / uncomment bug as reported by tareq. Included Synonyms in scripting engine ( nickt_ch ).IronPython: 2.7 Release Candidate 1: We are pleased to announce the first Release Candidate for IronPython 2.7. This release contains over two dozen bugs fixed in preparation for 2.7 Final. See the release notes for 60193 for details and what has already been fixed in the earlier 2.7 prereleases. - IronPython TeamCaliburn Micro: A Micro-Framework for WPF, Silverlight and WP7: Caliburn.Micro 1.0 RC: This is the official Release Candicate for Caliburn.Micro 1.0. The download contains the binaries, samples and VS templates. VS Templates The templates included are designed for situations where the Caliburn.Micro source needs to be embedded within a single project solution. This was targeted at government and other organizations that expressed specific requirements around using an open source project like this. NuGet This release does not have a corresponding NuGet package. The NuGet pack...Caliburn: A Client Framework for WPF and Silverlight: Caliburn 2.0 RC: This is the official Release Candidate for Caliburn 2.0. It contains all binaries, samples and generated code docs.Rawr: Rawr 4.0.20 Beta: Rawr is now web-based. The link to use Rawr4 is: http://elitistjerks.com/rawr.phpThis is the Cataclysm Beta Release. More details can be found at the following link http://rawr.codeplex.com/Thread/View.aspx?ThreadId=237262 As of the 4.0.16 release, you can now also begin using the new Downloadable WPF version of Rawr!This is a pre-alpha release of the WPF version, there are likely to be a lot of issues. If you have a problem, please follow the Posting Guidelines and put it into the Issue Trac...MiniTwitter: 1.66: MiniTwitter 1.66 ???? ?? ?????????? 2 ??????????????????? User Streams ?????????Windows Phone 7 Isolated Storage Explorer: WP7 Isolated Storage Explorer v1.0 Beta: Current release features:WPF desktop explorer client Visual Studio integrated tool window explorer client (Visual Studio 2010 Professional and above) Supported operations: Refresh (isolated storage information), Add Folder, Add Existing Item, Download File, Delete Folder, Delete File Explorer supports operations running on multiple remote applications at the same time Explorer detects application disconnect (1-2 second delay) Explorer confirms operation completed status Explorer d...Silverlight Toolkit: Silverlight for Windows Phone Toolkit - Feb 2011: Silverlight for Windows Phone Toolkit OverviewSilverlight for Windows Phone Toolkit offers developers additional controls for Windows Phone application development, designed to match the rich user experience of the Windows Phone 7. Suggestions? Features? Questions? Ask questions in the Create.msdn.com forum. Add bugs or feature requests to the Issue Tracker. Help us shape the Silverlight Toolkit with your feedback! Please clearly indicate that the work items and issues are for the phone t...New ProjectsCompetition Management Platform: Paragliding Competition Management PlatformCS424 B2 Group - Car Management: CS424 B2 Group - Car ManagementEMS: The main aim of the system to perform environment inventorization.EVVA: EVVA ist ein Softwareprojekt zur Unterstützung privater Arbeitsvermittler FileSocialVB: A library to work with the filesocial.com web site and API through VB.NET. This is actually an offshoot of the http://twittervb.codeplex.com project. Though smaller, this will lead to a more compact library.Hash Crack - IGProgram: Hash Crack is a software program for hashes and passwords cracking. Hash Crack use dictionary or set of symbols for hashes cracking, and also support pwdump file format for Windows passwords cracking NTHash MD4. MD2, MD4, MD5, SHA1, SHA256, SHA384, SHA512Imail Spammer Killer: Bots seem to love picking off the weak passwords of IpSwitch IMail v10 users and using SMTP auth to spam the world with their new found account access. This project is a windows service to isolate and stop this activity by disabling the violated user account as it occurs.JVS2USB: Montage permettant de relier une IO ( capcom / Sega ) sur un PC via l'USB !!Library Reminder: Library ReminderMAVI: mobile application for the visually impaired: bill recognition & tag and recognize objects based on a specific stickerMessage splliting without envelope in Biztalk 2009: Message splitting without envelope in Biztalk 2009. The project contains: - Source Code - Examples Article describing how to make it:Microsoft translator: Language translator designed to test Microsoft Translator web service API In Windows Phone 7 developed using Visual Studio 2010 in C#mrmuffin: Mr Muffin WP7 game for childrenNetwork Monitor: Simple application with a vu-meter style display of recent incoming network traffic. - Requires .NET 4, - Requires WinPCap (http://www.winpcap.org/) - Only tested to run under Windows 7NPhysics: NPhysics - Physical Data Types for .NETOpen SimRacing Results: Open SimRacing Results aims to provide an open standard for race results of PC SimRacing games (like iRacing, rFactor, NR2003, ...), allowing developers of league management systems to use a unique interface to get the results from, regardless of the simulation used.Orchard Image Gallery: Orchard Image Gallery project is intented to provide a Image Gallery content part and/or widget for the Orchard Project.Planning Poker for Windows Phone 7: Play planning poker on your Windows Phone 7.Publishing and consuming WCF in Biztalk 2009 and Visual Studio 2008: The file contains: Biztalk 2009 Project, C# Console Project, Example. Push Notification for Windows Phone 7 in php: WindowsPhonePushNotification enables you to use Microsoft Push Notification Service in phpQuksace Agjke: For more information, please visit <http://students.cs.tamu.edu/abe/IS_and_R/HW3/quksace%20agjke.html>. http://students.cs.tamu.edu/abe/IS_and_R/HW3/quksace%20agjke.html Read: a "GNU Make"-like utility for viewing Readme files: Read is a simple program to easily load and read README files on a UNIX-compliant system. It works in a similar way to GNU Make by searching a directory for a compatible file, in this case a Readme file, and loading it for reading using a text editor or viewer.SQL CE 3.5 persistence mapper for ECO IV: May need some adjustments for ECO V/VI, definitely needs some rewrite to support SQL CE 4.0 fullySQL Server Job Failure Notification System: A simple means of ensuring you know when SQLAgent jobs fail.SuperQuery: SuperQuery makes it easy to run the same batch of SQL across several databases on different SQL servers. SuperQuery supports all editions and versions of SQL Server from 2000 onwards. It is developed in C# using .NET 4 Client Profile.System.Net.Mail Extended: An Extension to the System.Net.Mail Namespace, adding a POP3 Client, Enhanced SMTP Client, IMAP Client, POP3 Server, SMTP Server, and IMAP Serve, all written in Visual C#.wow-combatlogs: A PowerShell module for working with combat logs generated by World of Warcraft.WPF UndoManager: WPF UndoManager provides a simple Undomanager on the base of WPF's CommandPattern. It use an implementation of the ICommand-interface to manage a history of actions.XO / TicTacToe game: Dynamic sized XO / TicTacToe game for Windows Phone 7 Build using Visual Studio 2010 and C#

    Read the article

  • How to make sure that grub does use menu.lst?

    - by Glen S. Dalton
    On my Ubuntu 9.04 ("Karmic") laptop I suspect grub does not use the /boot/grub/menu.lst file. What happens on boot is that I see a blank screen and nothing happens. When I press ESC I see a boot list which is different from what I would expect from the menu.lst file. The menu lines are different and when I choose the first entry it does not use the kernel options that are in the first entry in menu.lst. Where do the entries that grub uses come from? How can I find out what happens, is there a log? I could not find anything in /var/log/syslog or /var/log/dmesg about grub using a menu.lst. How can I set it to work like expected? Some Files: $ sudo ls -la /boot/grub/*lst -rw-r--r-- 1 root root 1558 2009-12-12 15:25 /boot/grub/command.lst -rw-r--r-- 1 root root 121 2009-12-12 15:25 /boot/grub/fs.lst -rw-r--r-- 1 root root 272 2009-12-12 15:25 /boot/grub/handler.lst -rw-r--r-- 1 root root 4576 2010-03-19 11:26 /boot/grub/menu.lst -rw-r--r-- 1 root root 1657 2009-12-12 15:25 /boot/grub/moddep.lst -rw-r--r-- 1 root root 62 2009-12-12 15:25 /boot/grub/partmap.lst -rw-r--r-- 1 root root 22 2009-12-12 15:25 /boot/grub/parttool.lst $ sudo ls -la /vm* lrwxrwxrwx 1 root root 30 2009-12-12 16:15 /vmlinuz -> boot/vmlinuz-2.6.31-16-generic lrwxrwxrwx 1 root root 30 2009-12-12 14:07 /vmlinuz.old -> boot/vmlinuz-2.6.31-14-generic $ sudo ls -la /init* lrwxrwxrwx 1 root root 33 2009-12-12 16:15 /initrd.img -> boot/initrd.img-2.6.31-16-generic lrwxrwxrwx 1 root root 33 2009-12-12 14:07 /initrd.img.old -> boot/initrd.img-2.6.31-14-generic The only menu.lst that I found: $ sudo find / -name "menu.lst" /boot/grub/menu.lst $ sudo cat /boot/grub/menu.lst # menu.lst - See: grub(8), info grub, update-grub(8) # grub-install(8), grub-floppy(8), # grub-md5-crypt, /usr/share/doc/grub # and /usr/share/doc/grub-doc/. ## default num # Set the default entry to the entry number NUM. Numbering starts from 0, and # the entry number 0 is the default if the command is not used. # # You can specify 'saved' instead of a number. In this case, the default entry # is the entry saved with the command 'savedefault'. # WARNING: If you are using dmraid do not use 'savedefault' or your # array will desync and will not let you boot your system. default 0 ## timeout sec # Set a timeout, in SEC seconds, before automatically booting the default entry # (normally the first entry defined). timeout 3 ## hiddenmenu # Hides the menu by default (press ESC to see the menu) #hiddenmenu # Pretty colours color cyan/blue white/blue ## password ['--md5'] passwd # If used in the first section of a menu file, disable all interactive editing # control (menu entry editor and command-line) and entries protected by the # command 'lock' # e.g. password topsecret # password --md5 $1$gLhU0/$aW78kHK1QfV3P2b2znUoe/ # password topsecret # examples # # title Windows 95/98/NT/2000 # root (hd0,0) # makeactive # chainloader +1 # # title Linux # root (hd0,1) # kernel /vmlinuz root=/dev/hda2 ro # Put static boot stanzas before and/or after AUTOMAGIC KERNEL LIST ### BEGIN AUTOMAGIC KERNELS LIST ## lines between the AUTOMAGIC KERNELS LIST markers will be modified ## by the debian update-grub script except for the default options below ## DO NOT UNCOMMENT THEM, Just edit them to your needs ## ## Start Default Options ## ## default kernel options ## default kernel options for automagic boot options ## If you want special options for specific kernels use kopt_x_y_z ## where x.y.z is kernel version. Minor versions can be omitted. ## e.g. kopt=root=/dev/hda1 ro ## kopt_2_6_8=root=/dev/hdc1 ro ## kopt_2_6_8_2_686=root=/dev/hdc2 ro # kopt=root=UUID=9b454298-18e1-43f7-a5bc-f56e7ed5f9c6 ro noresume ## default grub root device ## e.g. groot=(hd0,0) # groot=70fcd2b0-0ee0-4fe6-9acb-322ef74c1cdf ## should update-grub create alternative automagic boot options ## e.g. alternative=true ## alternative=false # alternative=true ## should update-grub lock alternative automagic boot options ## e.g. lockalternative=true ## lockalternative=false # lockalternative=false ## additional options to use with the default boot option, but not with the ## alternatives ## e.g. defoptions=vga=791 resume=/dev/hda5 ## defoptions=quiet splash # defoptions=apm=on acpi=off ## should update-grub lock old automagic boot options ## e.g. lockold=false ## lockold=true # lockold=false ## Xen hypervisor options to use with the default Xen boot option # xenhopt= ## Xen Linux kernel options to use with the default Xen boot option # xenkopt=console=tty0 ## altoption boot targets option ## multiple altoptions lines are allowed ## e.g. altoptions=(extra menu suffix) extra boot options ## altoptions=(recovery) single # altoptions=(recovery mode) single ## controls how many kernels should be put into the menu.lst ## only counts the first occurence of a kernel, not the ## alternative kernel options ## e.g. howmany=all ## howmany=7 # howmany=all ## specify if running in Xen domU or have grub detect automatically ## update-grub will ignore non-xen kernels when running in domU and vice versa ## e.g. indomU=detect ## indomU=true ## indomU=false # indomU=detect ## should update-grub create memtest86 boot option ## e.g. memtest86=true ## memtest86=false # memtest86=true ## should update-grub adjust the value of the default booted system ## can be true or false # updatedefaultentry=false ## should update-grub add savedefault to the default options ## can be true or false # savedefault=false ## ## End Default Options ## title Ubuntu 9.10, kernel 2.6.31-14-generic noresume uuid 70fcd2b0-0ee0-4fe6-9acb-322ef74c1cdf kernel /vmlinuz-2.6.31-14-generic root=UUID=9b454298-18e1-43f7-a5bc-f56e7ed5f9c6 ro quiet splash apm=on acpi=off noresume initrd /initrd.img-2.6.31-14-generic title Ubuntu 9.10, kernel 2.6.31-14-generic (recovery mode) uuid 70fcd2b0-0ee0-4fe6-9acb-322ef74c1cdf kernel /vmlinuz-2.6.31-14-generic root=UUID=9b454298-18e1-43f7-a5bc-f56e7ed5f9c6 ro sing le initrd /initrd.img-2.6.31-14-generic title Ubuntu 9.10, memtest86+ uuid 70fcd2b0-0ee0-4fe6-9acb-322ef74c1cdf kernel /memtest86+.bin ### END DEBIAN AUTOMAGIC KERNELS LIST These are the choices that grub displays after i press ESC: Ubuntu, Linux 2-6-31-16-generic Ubuntu, Linux 2-6-31-16-generic (recovery mode) Ubuntu, Linux 2-6-31-14-generic Ubuntu, Linux 2-6-31-14-generic (recovery mode) Memory test (memtest86+) Memory test (memtest86+, serial console 115200)

    Read the article

  • Encrypt remote linux server

    - by Margaret Thorpe
    One of my customers has requested that their web server is encrypted to prevent offline attacks to highly sensitive data contained in a mysql database and also /var/log. I have full root access to the dedicated server at a popular host. I am considering 3 options - FDE - This would be ideal, but with only remote access (no console) I imagine this would be very complex. Xen - installing XEN and moving their server within a XEN virtual machine and encrypting the VM - which seems easier to do remotely. Parition - encrypt the non-static partitions where the sensitive data resides e.g. /var /home etc. What would be the simplist approach that satisfies the requirements?

    Read the article

  • how to create a mirror of minimum size to install Ubuntu

    - by Registered User
    I need to create an http url at my laptop to have a Ubuntu installation begin within my laptop on a Xen environment. This is how the final thing will look like http://bderzhavets.wordpress.com/2008/10/28/install-ubuntu-intrepid-server-pv-domu-at-xen-33-port-via-httpgetco-centos-52-dom0/ the host and client are both going to be my laptop, I Google d and came across apt-mirror and some other packages. I do not want to archive entire 15 GB Ubuntu repositories on my machine. It is not possible to use a CD,ISO,loop mounted disk (reason mentioned below). I have tried using netboot image on local machine which failed because if you are attempting to create a virtual machine on a hardware which does not support VT virt-manager installer necessarily needs a URL of this sort http://archive.ubuntu.com/ubuntu/dists/hardy/main/installer-i386/current/images/netboot/ any other option to create guest OS is simply grayed out. The unfortunate part is my Ethernet connections do not work when I boot with Xen-4.0 and a pv-ops Dom0 kernel from Jeremy's tree.Which is where I have to do this work.So I have to create a URL structure which is similar to Ubuntu mirrors.So how can I do this in bare minimum so that at least the console boots and once the console comes I can do some work.

    Read the article

  • Cannot to change my root password on Xenserver

    - by Michlaou
    I try to change my root password on my Xenserver 6.0. I follow these steps: enter boot: menu.c32 selecet xe-serial and press tab add "single" before the 2nd triple hyphens and i press enter. I have that: mboot.c32 /boot/xen.gz com1=115200,8n1 console=com1, vga mem=1024G dom0_max_vcpus4 dom0_mem=752M lowmem_emergency_pool=1M crashkernel=64M@32M single --- /boot/vmlinuz-2.6-xen root=LABEL=root-rodraxar ro console=tty0 xencons=hvc console=hvc0 --- /boot/initrd-2.6-xen.img I have commande on the screen and it's stop at: ext3-fs: monted filesystem with ordered data mode. Can you help me?

    Read the article

  • Neighbour table overflow on Linux hosts related to bridging and ipv6

    - by tim
    Note: I already have a workaround for this problem (as described below) so this is only a "want-to-know" question. I have a productive setup with around 50 hosts including blades running xen 4 and equallogics providing iscsi. All xen dom0s are almost plain Debian 5. The setup includes several bridges on every dom0 to support xen bridged networking. In total there are between 5 and 12 bridges on each dom0 servicing one vlan each. None of the hosts has routing enabled. At one point in time we moved one of the machines to a new hardware including a raid controller and so we installed an upstream 3.0.22/x86_64 kernel with xen patches. All other machines run debian xen-dom0-kernel. Since then we noticed on all hosts in the setup the following errors every ~2 minutes: [55888.881994] __ratelimit: 908 callbacks suppressed [55888.882221] Neighbour table overflow. [55888.882476] Neighbour table overflow. [55888.882732] Neighbour table overflow. [55888.883050] Neighbour table overflow. [55888.883307] Neighbour table overflow. [55888.883562] Neighbour table overflow. [55888.883859] Neighbour table overflow. [55888.884118] Neighbour table overflow. [55888.884373] Neighbour table overflow. [55888.884666] Neighbour table overflow. The arp table (arp -n) never showed more than around 20 entries on every machine. We tried the obvious tweaks and raised the /proc/sys/net/ipv4/neigh/default/gc_thresh* values. FInally to 16384 entries but no effect. Not even the interval of ~2 minutes changed which lead me to the conclusion that this is totally unrelated. tcpdump showed no uncommon ipv4 traffic on any interface. The only interesting finding from tcpdump were ipv6 packets bursting in like: 14:33:13.137668 IP6 fe80::216:3eff:fe1d:9d01 > ff02::1:ff1d:9d01: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:9d01, length 24 14:33:13.138061 IP6 fe80::216:3eff:fe1d:a8c1 > ff02::1:ff1d:a8c1: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:a8c1, length 24 14:33:13.138619 IP6 fe80::216:3eff:fe1d:bf81 > ff02::1:ff1d:bf81: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:bf81, length 24 14:33:13.138974 IP6 fe80::216:3eff:fe1d:eb41 > ff02::1:ff1d:eb41: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:eb41, length 24 which placed the idea in my mind that the problem maybe related to ipv6, since we have no ipv6 services in this setup. The only other hint was the coincidence of the host upgrade with the beginning of the problems. I powered down the host in question and the errors were gone. Then I subsequently took down the bridges on the host and when i took down (ifconfig down) one particularly bridge: br-vlan2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:120 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5286 (5.1 KiB) TX bytes:726 (726.0 B) eth0.2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1801 errors:0 dropped:0 overruns:0 frame:0 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:126228 (123.2 KiB) TX bytes:1464 (1.4 KiB) bridge name bridge id STP enabled interfaces ... br-vlan2158 8000.0026b9fb162c no eth0.2158 br-vlan2159 8000.0026b9fb162c no eth0.2159 The errors went away again. As you can see the bridge holds no ipv4 address and it's only member is eth0.2159 so no traffic should cross it. Bridge and interface .2159 / .2157 / .2158 which are in all aspects identical apart from the vlan they are connected to had no effect when taken down. Now I disabled ipv6 on the entire host via sysctl net.ipv6.conf.all.disable_ipv6 and rebooted. After this even with bridge br-vlan2159 enabled no errors occur. Any ideas are welcome.

    Read the article

  • Which virtualization solutions are available for non-x86 platforms?

    - by asmaier
    Are their any virtualization solutions like Xen, KVM and VMWare ESX available for non-x86 platform? Especially I'm interested if there are solutions available or if Xen, KVM can be made to run on the platforms POWER5/6/7 PowerPC Itanium 64 NEC SX-8/9 Cray X2 BlueGene What are your experiences? Is it possible to virtualize GPUs like Nvidias Tesla/Fermi?

    Read the article

  • p2v v2v v2p tool from open source?

    - by neolix
    we have centos, fedora, ubuntu server and desktop we are looking for good open source tool for p2v v2v v2p and we are not using vmware here only we use xen or kvm. Same of the server shifted to new hardware and same of the server on xen or kvm. Can same help me !!

    Read the article

  • Debian Linux bridging router intermittently dropping packets [migrated]

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Can anybody help?

    Read the article

  • KVM and JBoss Java Application Server

    - by Jason
    We have a large Xen deployment running on both RHEL and CentOS and have recently started looking at KVM since this is where it looks like the future of VM's are on Linux. We can load the server and get everything running without an issue. However when we load up a new one with JBoss (4.2 Community edition, Sun JDK 6) and load a large EAR the server goes a little crazy. The %sy will jump to 80-99% and just hang for large periods of time we see a similar jump in %us on the host machine. We though at first this might be I/O as it seems to happen at start of JBoss but then would "cool down" after everything got loaded. We did some tests by extracting some large tar.gz files and using jar -xvf on the ear but could not re-create. Then we starting thinking this might be some type of memory access issues. We loaded a c-program that would generate a lot of memory activity and sure enough we saw the spikes again. Not as high mind you but we did see it jump. We then wrote a small java program to do the same thing and sure enough we saw it jump again. Any thoughts on what might be causing this? Is this just the way KVM works? As a side note we do NOT see this behavior on any other setup. Xen, VMWare and/or native iron. The system does seem a bit slower than our Xen / VMware ones.

    Read the article

  • Possible to host CentOS netinstall files on a local HTTP/FTP?

    - by garlicman
    I'm running XenServer on an Dell R610 and am running into a catch-22. During install from DVD, CentOS can't find the DVD package catalogue. It's a reported error for some, XenServer + CentOS6 + DVD install in some hardware configurations = failed install. Yes, I checked the MD5 and let the disc test pass. In every reported case, the netinstall was the solution. The issue is my net access is required to go through a web proxy that prompts before you can download a file. This naturally breaks any download automation. I've been waiting on our IT to put in an exception rule to allow my lab to bypass the prompt, but it's been over 3 weeks now and they don't seem responsive. (I've been working on this a day or two a week) I want to try and host the netinstall files local in my Xen network. Right now I only have a bunch of Windows based VMs, CentOS won't install so I don't have any Linux tools. I had tried simply hosting all the DVD contents off one of the Windows servers using Mongoose. (I didn't want to setup IIS) I copied them to a hosted sub-directory similar to all the mirrors out there (e.g. http:///centos/6.2/os/i386/) with no auth or anything. Then in the netinstall I correctly pointed to it. I now realize just copying the DVD files over won't work. The repodata will point to a local device, not the site I'm hosting. (e.g. the DVD repodata includes xml that points to where the packages are) Clearly I'm hosting them over HTTP, not from a DVD. Is there an easy way to sort this out? I'm just trying to install CentOS6 on Xen. If there's a turnkey downloadable Xen image with CentOS 6.2 on it, or a downloadable repo image, I'll take that too! Thank you in advance!

    Read the article

  • Router intermittently failing

    - by nomen
    My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. All of these things work most of the time, but break down intermittently, for a few minutes at a time. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing between the bridge and my internet-facing interface: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw Ping(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Also, the router is currently "working", and I checked on a problematic client: arp infrastructure infrastructure.mydomain (10.47.94.1) at 0:23:54:bb:7d:ce on en0 ifscope [ethernet] I tried it when the router was down, and I (eventually) got the same response. It took about 30 seconds to return, though.

    Read the article

  • Which virtualization solutions are available for non-x86 platforms?

    - by asmaier
    Are their any virtualization solutions like Xen, KVM and VMWare ESX available for non-x86 platform? Especially I'm interested if there are solutions available or if Xen, KVM can be made to run on the platforms POWER5/6/7 PowerPC Itanium 64 NEC SX-8/9 Cray X2 BlueGene What are your experiences? Is it possible to virtualize GPUs like Nvidias Tesla/Fermi?

    Read the article

  • Converting a PV vm back into an HVM vm

    - by wim.coekaerts
    I have been doing some Oracle VM benchmark stuff in the last week or 2 in my off hours and yesterday I wanted to convert one of my VMs that was based on a paravirt kernel into a vm that just boots as a regular hardware virt VM with a standard x86-64 kernel. It took me a little while to figure out the fastest way so now that I have it pretty much down I wanted to share the steps. A PV kernel uses pygrub and a paravirt kernel image that lives on the vm image virtual disk. since this disk image does not have to be bootable it doesn't contain a boot sector and if you just restart the VM in hvm mode the virtual bios will just not do much as it can't start the boot process from disk The first thing I do is make a backup of my vm.cfg file :-) and then edit it as follows : the original file contains : bootloader = '/usr/bin/pygrub' I replace that with : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' kernel = '/usr/lib/xen/boot/hvmloader' then changing the disk files. I change my xvd disks to hd disks and I copy over the iso image of my instal lDVD. In the case of my VM template it was based on OL5U4 So I downloaded Enterprise-R5-U4-Server-x86_64-dvd.iso and added it as a cd device. disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,xvda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,xvdb,w', ] to disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,hda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,hdb,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Enterprise-R5-U4-Server-x86_64-dvd.iso, hdc:cdrom,r', ] boot='d' for the network devices (vifs) I change : vif = ['bridge=xenbr2,type=netfront'] to vif = ['bridge=xenbr2,type=ioemu'] That should do it. Next, inside the VM, I copy over the regular kernel rpm that I want to end up running in hvm mode. In this example case it was : kernel-2.6.18-164.0.0.0.1.el5.x8664.rpm. I will use that later on in the process. I put this kernel simply in /root At this point I just start the vm with xm create vm.cfg and start my vnc console to the vm console. Oracle Linux will boot from the iso image, I just go through the install steps and click on UPgrade existing (not re-install). Because the VM is the same as the ISO the install won't actually do anything and it will run through instantly. When the "Reboot" button pops up, don't reboot. Switch to the command prompt console. hi alt-f2 to go to the shell prompt. Now it's easy : umount /mnt/sysimage/boot cd /mnt/sysimage chroot . mount /dev/hda1 (if that was your /boot partition) export PATH=/sbin:$PATH (just to clean that up) edit /etc/modprobe.conf and comment out the xen modules (just put a # in front) Install grub. if your /boot is hda1 then that is (hd0,0) $ grub root (hd0,0) setup (hd0) exit grub now you have a good bootsector, grub installed and you have your grub.conf file Install the new kernel cd root (this is your old /root in your pv image) rpm -ivh remove (or comment out) boot='d' in your vm.cfg restart the VM and you should be good to go, regular grub should start and load your environment. Caveats : this assumes you used labels for your filesystems. if /etc/fstab were to have devices listed then you would have to rename these device before rebooting as well. If you had a /dev/xvda disk then this would be /dev/hda or /dev/sda. All in all it is a relatively short and simple process.

    Read the article

  • Converting a PV vm back into an HVM vm

    - by wim.coekaerts
    I have been doing some Oracle VM benchmark stuff in the last week or 2 in my off hours and yesterday I wanted to convert one of my VMs that was based on a paravirt kernel into a vm that just boots as a regular hardware virt VM with a standard x86-64 kernel. It took me a little while to figure out the fastest way so now that I have it pretty much down I wanted to share the steps. A PV kernel uses pygrub and a paravirt kernel image that lives on the vm image virtual disk. since this disk image does not have to be bootable it doesn't contain a boot sector and if you just restart the VM in hvm mode the virtual bios will just not do much as it can't start the boot process from disk The first thing I do is make a backup of my vm.cfg file :-) and then edit it as follows : the original file contains : bootloader = '/usr/bin/pygrub' I replace that with : acpi = 1 apic = 1 builder = 'hvm' device_model = '/usr/lib/xen/bin/qemu-dm' kernel = '/usr/lib/xen/boot/hvmloader' then changing the disk files. I change my xvd disks to hd disks and I copy over the iso image of my instal lDVD. In the case of my VM template it was based on OL5U4 So I downloaded Enterprise-R5-U4-Server-x86_64-dvd.iso and added it as a cd device. disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,xvda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,xvdb,w', ] to disk = ['file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/System.img,hda,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Oracle11202RAC_x86_64-xvdb.img,hdb,w', 'file:/ovs/OVM_EL5U4_X86_64_11202RAC_PVM/Enterprise-R5-U4-Server-x86_64-dvd.iso, hdc:cdrom,r', ] boot='d' for the network devices (vifs) I change : vif = ['bridge=xenbr2,type=netfront'] to vif = ['bridge=xenbr2,type=ioemu'] That should do it. Next, inside the VM, I copy over the regular kernel rpm that I want to end up running in hvm mode. In this example case it was : kernel-2.6.18-164.0.0.0.1.el5.x8664.rpm. I will use that later on in the process. I put this kernel simply in /root At this point I just start the vm with xm create vm.cfg and start my vnc console to the vm console. Oracle Linux will boot from the iso image, I just go through the install steps and click on UPgrade existing (not re-install). Because the VM is the same as the ISO the install won't actually do anything and it will run through instantly. When the "Reboot" button pops up, don't reboot. Switch to the command prompt console. hi alt-f2 to go to the shell prompt. Now it's easy : umount /mnt/sysimage/boot cd /mnt/sysimage chroot . mount /dev/hda1 (if that was your /boot partition) export PATH=/sbin:$PATH (just to clean that up) edit /etc/modprobe.conf and comment out the xen modules (just put a # in front) Install grub. if your /boot is hda1 then that is (hd0,0) $ grub root (hd0,0) setup (hd0) exit grub now you have a good bootsector, grub installed and you have your grub.conf file Install the new kernel cd root (this is your old /root in your pv image) rpm -ivh remove (or comment out) boot='d' in your vm.cfg restart the VM and you should be good to go, regular grub should start and load your environment. Caveats : this assumes you used labels for your filesystems. if /etc/fstab were to have devices listed then you would have to rename these device before rebooting as well. If you had a /dev/xvda disk then this would be /dev/hda or /dev/sda. All in all it is a relatively short and simple process.

    Read the article

  • Virtualizor + VPS Backup (Bare Metal Restore capable) Using rSync 3

    - by Gaia
    I am using virtualizor to manage 3 XEN VPS. Hardware node and each VPS run CentOS 5.x. My backup needs are as follows: 1) I need to be able to bare metal restore the entire hardware node, excluding the VPSes (which would be restored via #2 below) 2) I need to have a complete backup of each VPS, ideally a backup that can be deployed on any other host that uses Xen, if the need arises. Naturally, I would also need to use this backup to restore an entire VPS to an earlier state within the same host. Which folders rSync needs to keep backed up in order to accomplish the above? The rSync specialists aren't sure of it either. Thanks

    Read the article

  • Linux Kernel IRQ Routing with irqbalance / kernel options

    - by tim
    I'm trying to get my Xen Dom0 distributing the irqs in an smp enviroment. As far as I know there are 2 Options: Use irqbalance Configure the kernel without cpu hotplug support My System is Debian Squeeze, Xen 4.0.4, Kernel 3.2.31. My Problem is: irqbalance segfaults due to a changed /proc/irq* layout or irq0 missing (this seems to be a very old bug existing since Lenny) To configure a kernel without cpu hotplug support you must disable cpu powermanagement which seems to be impossible through the standard wys (make config / make menuconfig) - the option CONFIG_PM simply defaults to "Y". Any idea anyone on how to get a debian dom0 kernel with a proper irq distribution?

    Read the article

  • Xencenter guest will not boot

    - by Georgi
    I have xen server free edition. Today one of the guest VM was very loaded and I decided to reboot it. Now it can not start. It is with Ubuntu 10.04 Server. The machine is shown as running in xsconsole and in windows Xen control center. It shows 100 % CPU and 100 % RAM usage. The console shows nothing (it doesn't show boot process). And the worst is that I have no backup. Is there any advice how to see what is going on. I exported it to file and now I am trying it to import it into another server, because I can't reboot the physical server it runs on. Can this save me (the reboot of the server) Thank you

    Read the article

  • Xenserver boot error

    - by Adrian
    I'm trying to get Xenserver 5.5 running on a spare computer here, hardware specs: Intel Q6600, 4GB Ram, and Gigabyte GA-P35-DS3R motherboard Xenserver itself installs fine onto a 150GB sata hdd, however it fails to boot whatsoever, giving this garbled mess: http://img697.imageshack.us/img697/9918/biosi.jpg it's not frozen because if I press enter it just prints a different garble and it also says "could not find kernel image". The strangest thing is if I put that hdd in my desktop and assign it to a VMWare desktop vm (under the ESX profile no less) it boots perfectly... leading me to believe there are no problems with the install or the hdd itself. From what I can tell the error seems to be occuring completely seperately to Xenserver, in the bootloader extlinux?. If there was a motherboard compatibility issue I would think it would also have manifested during installation, and the fact the problem seems to be with the booting into Xen makes me doubt this. Any ideas guys? (I'm using Xen because it can do PCI passthrough without VT-d.)

    Read the article

  • Very slow printing from print server

    - by evolvd
    Print server is a VM on Xen The VM is Windows 2003 32bit. During the issue the VM is not being taxed in anyway, cpu, memory, hd read/write, and network speed is all good. The problem that I see is the transfer of the print file from the print server to the printer. The 80Mb file is transferred from the client to the print server in about 2 minutes but then it takes about 2 hours for that file to be sent to the printer. I can't figure out why this would just start to happen. The printer is rebooted every evening and is just used for one large print job in the morning. The server has been rebooted with no effect I changed the spool option to send the entire spool to the server before printing starts and it had no effect. This printer problem did happen to come about after some changes to the Xen environment. The Xen servers changed from using HBA NIC cards to software iscsi and a new switch was put in. I don't think this is related to the problem since all the speeds on the VMs are better now. The changed happened on Saturday and the first print to this printer happened on Monday morning. I'm just putting that out there but like I said I don't think it is related but I don't want to rule it out. At this point I don't have many other options besides the physical layer. I can switch out network cable that goes to the printer and I might be able to print the same job to another printer. I wont be able to test those things out till this afternoon though. Any other ideas or test I could do to try to find the reason for the slow speed? I forgot to say that this is only happening when printing to this one printer. ===Update=== I found out that there are a few printers that currently have this issue, not just the one. There are over 30 printers on the server though so I know it's not happening to all of them. I printed a large pdf doc from the server and it was able to print at the normal speed. If the machine sends the large print request it gets to the server fine but then slow to get from the server to the printer. If sent directly from the printer it gets to the printer at the normal speed. The question now is why is there a speed difference when it comes from the machine and why would it start now?

    Read the article

  • Simple Central Storage for HA mail server

    - by jtnire
    Hi Everyone, I will have 2 Postfix servers. One will be a backup of the other. What is the easiest method to provide central storage to both of these boxes? My infrastructure is very simple: Just a lot of Xen hosts, so there is no SAN or anything. Each Xen host does have RAID1 though. I don't mind mounting NFS shares on each of those mail servers, as long as the NFS server wasn't a single point of failure. Is there such a thing as redundant NFS? Any help would be appreciated Thanks

    Read the article

< Previous Page | 9 10 11 12 13 14 15 16 17 18 19 20  | Next Page >