Search Results

Search found 12537 results on 502 pages for 'solid state'.

Page 130/502 | < Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >

  • Best Processor for MediaSmart Server?

    - by Kent Boogaart
    I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

    Read the article

  • Linux policy routing - packets not coming back

    - by Bugsik
    i am trying to set up policy routing on my home server. My network looks like this: Host routed VPN gateway Internet link through VPN 192.168.0.35/24 ---> 192.168.0.5/24 ---> 192.168.0.1 DSL router 10.200.2.235/22 .... .... 10.200.0.1 VPN server The traffic from 192.168.0.32/27 should be and is routed through VPN. I wanted to define some routing policies to route some traffic from 192.168.0.5 through VPN as well - for start - from user with uid 2000. Policy routing is done using iptables mark target and ip rule fwmark. The problem: When connecting using user 2000 from 192.168.0.5 tcpdump shows outgoing packets, but nothing comes back. Traffic from 192.168.0.35 works fine (here I am not using fwmark but src policy). Here is my VPN gateway setup: # uname -a Linux placebo 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux # iptables -V iptables v1.4.12 # ip -V ip utility, iproute2-ss111117 IPtables rules (all policies in table filter are ACCEPT) # iptables -t mangle -nvL Chain PREROUTING (policy ACCEPT 770K packets, 314M bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 767K packets, 312M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 5520 packets, 1920K bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 782K packets, 901M bytes) pkts bytes target prot opt in out source destination 74 4707 MARK all -- * * 0.0.0.0/0 0.0.0.0/0 owner UID match 2000 MARK set 0x3 Chain POSTROUTING (policy ACCEPT 788K packets, 903M bytes) pkts bytes target prot opt in out source destination # iptables -t nat -nvL Chain PREROUTING (policy ACCEPT 996 packets, 51172 bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy ACCEPT 7 packets, 432 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1364 packets, 112K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 2302 packets, 160K bytes) pkts bytes target prot opt in out source destination 119 7588 MASQUERADE all -- * vpn 0.0.0.0/0 0.0.0.0/0 Routing: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master lan state UNKNOWN qlen 1000 link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff valid_lft forever preferred_lft forever 3: lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:40:63:f9:c3:8f brd ff:ff:ff:ff:ff:ff inet 192.168.0.5/24 brd 192.168.0.255 scope global lan inet6 fe80::240:63ff:fef9:c38f/64 scope link valid_lft forever preferred_lft forever 4: vpn: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 100 link/none inet 10.200.2.235/22 brd 10.200.3.255 scope global vpn # ip rule show 0: from all lookup local 32764: from all fwmark 0x3 lookup VPN 32765: from 192.168.0.32/27 lookup VPN 32766: from all lookup main 32767: from all lookup default # ip route show table VPN default via 10.200.0.1 dev vpn 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 # ip route show default via 192.168.0.1 dev lan metric 100 10.200.0.0/22 dev vpn proto kernel scope link src 10.200.2.235 192.168.0.0/24 dev lan proto kernel scope link src 192.168.0.5 TCP dump showing no traffic coming back when connection is made from 192.168.0.5 user 2000 # tcpdump -i vpn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vpn, link-type RAW (Raw IP), capture size 65535 bytes ### Traffic from user 2000 on 192.168.0.5 ### 10:19:05.629985 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6887764 ecr 0,nop,wscale 4], length 0 10:19:21.678001 IP 10.200.2.235.37291 > 10.100-78-194.akamai.com.http: Flags [S], seq 2868799562, win 14600, options [mss 1460,sackOK,TS val 6891776 ecr 0,nop,wscale 4], length 0 ### Traffic from 192.168.0.35 ### 10:23:12.066174 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [S], seq 2294159276, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 557451322 ecr 0,sackOK,eol], length 0 10:23:12.265640 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [S.], seq 2521908813, ack 2294159277, win 14480, options [mss 1367,sackOK,TS val 388565772 ecr 557451322,nop,wscale 1], length 0 10:23:12.276573 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [.], ack 1, win 8214, options [nop,nop,TS val 557451534 ecr 388565772], length 0 10:23:12.293030 IP 10.200.2.235.49247 > 10.100-78-194.akamai.com.http: Flags [P.], seq 1:480, ack 1, win 8214, options [nop,nop,TS val 557451552 ecr 388565772], length 479 10:23:12.574773 IP 10.100-78-194.akamai.com.http > 10.200.2.235.49247: Flags [.], ack 480, win 7776, options [nop,nop,TS val 388566081 ecr 557451552], length 0

    Read the article

  • Hostname Problem On WHM / cPanel Installation

    - by Eray
    My CentOS 5.6 server's hostname was "centos" . And then i change it to my domain : hostname domain.com And i started to installing WHM / cPanel as explained in here : http://etwiki.cpanel.net/twiki/bin/view/AllDocumentation/InstallationGuide/InstallingCpanel It's installed very well. And the i reboot my server. After rebooting, i was execute this command for open WHM's 2087 port : iptables -I RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 2087 -j ACCEPT Now i'm trying to browse domain.com:2087 i'm getting Server (centos) not found .I noticed it's forwarding to my old hostname (centos) . And then execute this command to verify me hostname hostname it's returned "centos" again. I'm not sure, why it's returned to old hostname. (I think it returned to old hostname after rebooting) . I'm changed it one more time : hostname domain.com Finally, now my hostname is domain.com . BUt still i'm getting centos server not found error. This is result of iptables -L command. P.S. : domain.com/cpanel is working

    Read the article

  • sysprep failure on Windows Server 2008

    - by dushyantp
    Before deploying a Azure VM Role, we need to perform %windir%\system32\sysprep\sysprep.exe /generalize /oobe /shutdown But in my case the sysprep fails with the log file %windir%\system32\sysprep\Panther\setuperr.txt saying: 2012-07-05 08:03:57, Error [0x0f0073] SYSPRP RunExternalDlls:Not running DLLs; either the machine is in an invalid state or we couldn't update the recorded state, dwRet = 31 2012-07-05 08:03:57, Error [0x0f00ae] SYSPRP WinMain:Hit failure while processing sysprep cleanup external providers; hr = 0x8007001f I do not always want to create a new image. Is there any work around? I followed the instructions in MS support here and tried: %windir%\system32\sysprep\sysprep.exe /generalize /oobe /shutdown /unattend:.\unattend.xml It did not work. Under certain circumstances, I need to tear down the VM Image from azure and re-deploy with some more changes. So sysprep has to run almost twice every week.

    Read the article

  • How to run node.js app on port 80? Are processes blocking my port?

    - by Lucas
    I believe the port 80 on my remote instance is blocked, and I am trying to run a node.js app using port 80. I have experimented with ports 3000 and 3002, and both ports are working fine, but I get an error when running on port 80. I suspect port 80 is blocked from my output of netstat -an below, but how can I find the process id's of the addresses that are blocking port 80 below? [lucas@ecoinstance]~/node/nodetest1$ netstat -an Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:3002 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:27017 127.0.0.1:51108 ESTABLISHED tcp 0 0 127.0.0.1:51106 127.0.0.1:27017 ESTABLISHED tcp 0 0 127.0.0.1:27017 127.0.0.1:51106 ESTABLISHED tcp 0 0 127.0.0.1:51107 127.0.0.1:27017 ESTABLISHED tcp 0 0 10.240.241.116:3002 174.61.171.61:36583 TIME_WAIT tcp 0 0 127.0.0.1:27017 127.0.0.1:51109 ESTABLISHED tcp 0 0 10.240.241.116:42423 169.254.169.254:80 ESTABLISHED tcp 0 0 127.0.0.1:51108 127.0.0.1:27017 ESTABLISHED tcp 0 532 10.240.241.116:22 174.61.171.61:56824 ESTABLISHED tcp 0 0 127.0.0.1:27017 127.0.0.1:51107 ESTABLISHED tcp 0 0 10.240.241.116:42412 169.254.169.254:80 ESTABLISHED tcp 0 0 127.0.0.1:51109 127.0.0.1:27017 ESTABLISHED tcp 0 0 127.0.0.1:51105 127.0.0.1:27017 ESTABLISHED tcp 0 0 10.240.241.116:42422 169.254.169.254:80 TIME_WAIT tcp 0 0 127.0.0.1:27017 127.0.0.1:51105 ESTABLISHED tcp6 0 0 :::22 :::* LISTEN udp 0 0 0.0.0.0:49948 0.0.0.0:* udp 0 0 0.0.0.0:68 0.0.0.0:* udp 0 0 10.240.241.116:123 0.0.0.0:* udp 0 0 127.0.0.1:123 0.0.0.0:* udp 0 0 0.0.0.0:123 0.0.0.0:* udp6 0 0 :::12151 :::* udp6 0 0 :::123 :::* Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 405680 /tmp/ssh-KdkxJfFLpKTC/agent.22 813 unix 2 [ ACC ] STREAM LISTENING 408230 /tmp/ssh-ofUeNNEwAqtP/agent.22 243 unix 2 [ ACC ] STREAM LISTENING 416227 /tmp/mongodb-27017.sock unix 2 [ ACC ] SEQPACKET LISTENING 3692 /run/udev/control unix 7 [ ] DGRAM 5286 /dev/log unix 2 [ ACC ] STREAM LISTENING 5318 /var/run/acpid.socket unix 2 [ ACC ] STREAM LISTENING 16170 /tmp//tmux-1000/default unix 2 [ ACC ] STREAM LISTENING 414450 /var/run/dbus/system_bus_socke And here is the log when trying to run on port 80 with node.js: [lucas@ecoinstance]~/node/nodetest1$ npm start > [email protected] start /home/lucas/node/nodetest1 > node ./bin/www events.js:72 throw er; // Unhandled 'error' event ^ Error: listen EACCES at errnoException (net.js:904:11) at Server._listen2 (net.js:1023:19) at listen (net.js:1064:10) at Server.listen (net.js:1138:5) at Function.app.listen (/home/lucas/node/nodetest1/node_modules/express/lib/applicati on.js:532:24) at Object.<anonymous> (/home/lucas/node/nodetest1/bin/www:7:18) at Module._compile (module.js:456:26) at Object.Module._extensions..js (module.js:474:10) at Module.load (module.js:356:32) at Function.Module._load (module.js:312:12) npm ERR! [email protected] start: `node ./bin/www` npm ERR! Exit status 8 npm ERR! npm ERR! Failed at the [email protected] start script. npm ERR! This is most likely a problem with the nodetest1 package, npm ERR! not with npm itself. npm ERR! Tell the author that this fails on your system: npm ERR! node ./bin/www npm ERR! You can get their info via: npm ERR! npm owner ls nodetest1 npm ERR! There is likely additional logging output above. npm ERR! System Linux 3.13-0.bpo.1-amd64 npm ERR! command "/usr/local/bin/node" "/usr/local/bin/npm" "start" npm ERR! cwd /home/lucas/node/nodetest1 npm ERR! node -v v0.10.28 npm ERR! npm -v 1.4.9 npm ERR! code ELIFECYCLE npm ERR! npm ERR! Additional logging details can be found in: npm ERR! /home/lucas/node/nodetest1/npm-debug.log npm ERR! not ok code 0 And sudo netstat -lnp does not return any matching port 80's: [lucas@ecoinstance]~/node/nodetest1$ sudo netstat -lnp [48/648] Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Progr am name tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 29160/mon god tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1976/sshd tcp6 0 0 :::22 :::* LISTEN 1976/sshd udp 0 0 0.0.0.0:49948 0.0.0.0:* 1604/dhcl ient udp 0 0 0.0.0.0:68 0.0.0.0:* 1604/dhcl ient udp 0 0 10.240.241.116:123 0.0.0.0:* 2076/ntpd udp 0 0 127.0.0.1:123 0.0.0.0:* 2076/ntpd udp 0 0 0.0.0.0:123 0.0.0.0:* 2076/ntpd udp6 0 0 :::12151 :::* 1604/dhcl ient udp6 0 0 :::123 :::* 2076/ntpd Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node PID/Program name Path unix 2 [ ACC ] STREAM LISTENING 405680 22814/ssh-agent /tmp/ssh-K dkxJfFLpKTC/agent.22813 unix 2 [ ACC ] STREAM LISTENING 408230 24049/ssh-agent /tmp/ssh-o fUeNNEwAqtP/agent.22243 unix 2 [ ACC ] STREAM LISTENING 416227 29160/mongod /tmp/mongo db-27017.sock unix 2 [ ACC ] SEQPACKET LISTENING 3692 284/udevd /run/udev/ control unix 2 [ ACC ] STREAM LISTENING 5318 1798/acpid /var/run/a cpid.socket unix 2 [ ACC ] STREAM LISTENING 16170 5177/tmux /tmp//tmux -1000/default unix 2 [ ACC ] STREAM LISTENING 414450 28213/dbus-daemon /var/run/d bus/system_bus_socket unix 2 [ ACC ] STREAM LISTENING 404225 22324/1 /tmp/ssh-9 TlDmu4bjl/agent.22324

    Read the article

  • DHCP: server behavior in a two server situation

    - by lang2
    This is a question w.r.t server behavior in the DHCP standard. I've read the RFC and it's still not clear to me. Situation is this: There are two DHCP servers on a network. My client initially get IP address from server A. At some stage, server A goes down. My poor client is sending REQUEST in RENEW and then REBIND state, with no response whatsoever. My questions is: in this situation, should server B response to the REQUEST in REBIND state, e.g. DHCPNAK? Thanks, lang2

    Read the article

  • SQL Server: Is it possible to prevent SQL Agent from failing a step on error?

    - by franklinkj
    I have a stored procedure that runs custom backups for around 60 SQL servers (mixes 2000 through 2008R2). Occasionally, due to issues outside of my control (backup device inaccessible, network error, etc.) an individual backup on one or two databases will fail. This causes this entire step to fail, which means any subsequent backup commands are not executed and half of the databases on a given server may not be backed up. On the 2005+ boxes I am using TRY/CATCH blocks to manage these problems and continue backing up the remaining databases. On a 2000 server however, for example, I have no way to prevent this error from failing the entire step: Msg 3201, Level 16, State 1, Line 1 Cannot open backup device 'db-diff(\PATH\DB-DIFF-03-16-2010.DIF)'. Operating system error 5(Access is denied.). Msg 3013, Level 16, State 1, Line 1 BACKUP DATABASE is terminating abnormally. I am simply asking if anything like this is possible in SQL 2000 or if I need to go in a completely different direction.

    Read the article

  • Windows Fax Server Leaves Documents in "Pending" Status

    - by Chris
    We are having an issue with Windows Fax Server on Windows Server 2008. Occasionally, the server will get into a state where after adding jobs to the outbox, they will simply remain at the pending status (without any attempt to send them). There is nothing in the event log mentioning a problem. It typically seems to enter the state after restarting the server or after no faxes have been sent for a while. The way to fix the issue has been to: Stop the Fax service Go into the modem properties in device manager and query modem Start the Fax service - at which point all the pending faxes in the outbox will send.

    Read the article

  • Try to delete files used by IIS

    - by Cédric Boivin
    I got a service coded in c# whoes deleted somes web site files hosted on iis, before an update. But sometime when i delete the files, they stay there. If I try to delete them manually, via explorer, the file are not deletable, because they are in state "Delete pending". There is the way my service try to delete the file try { // Enlève tout les attributs sur le fichiers afin de s'assurer que le fichier n'est pas en lecture seul File.SetAttributes(file, FileAttributes.Normal); // Supprime le fichier File.Delete(file); } It's there a way to avoid this state ? What can i do to force the delete by c# code? Could i release all process to the file by c# code ? The environnement is IIS 7.5 Windows 2008-r2 .net 4.0 Thanks

    Read the article

  • Both servers running keepalived become master

    - by pcent
    After a network failure,both servers running keepalived become master. When the network is reestablished, both keep the MASTER state. What could be causing it? Edited: Another information that might be relevant, each server has two NICs. Here is the virtual instance configuration: vrrp_instance VGAPP { interface eth0 virtual_router_id 61 state BACKUP nopreempt priority 50 advert_int 3 virtual_ipaddress { 10.26.57.61/24 } track_interface { eth0 } track_script { jboss_check #tomcat_check #interface_check #interface_check02 } notify_master "/opt/keepalived/scripts/set_state.sh MASTER" notify_backup "/opt/keepalived/scripts/set_state.sh BACKUP" notify_fault "/opt/keepalived/scripts/set_state.sh FAULT" notify_stop "/opt/keepalived/scripts/set_state.sh STOPPED"}

    Read the article

  • Redhat doesn't set my desired hostname on reboot

    - by tomdee
    I have a redhat (EL5) server that I need to change the hostname on. I'm trying to put it back into a known state to help with server provisioning activities. As part of changing the hostname, I'm updating /etc/sysconfig/network and /etc/hosts. I also have an explicit call to hostname. My desired state is that the server thinks its hostname is "localhost". And a call to "hostname" returns "localhost". The problem I'm having is that when I reboot, the hostname is reverted to "localhost.companyname.com" which is not what I want. How do I ensure that the hostname is set up as just "localhost" when I reboot? My /etc/sysconfig/network file contains: NETWORKING=yes HOSTNAME=localhost GATEWAY=123.123.123.123 #I do have a proper IP address here My /etc/hosts file contains: 127.0.0.1 localhost.localdomain localhost 172.21.1.1 localhost.companyname.com localhost

    Read the article

  • iptables logging to diferent file via syslog-ng

    - by rahrahruby
    I have the following configuration in my iptables and syslog files: IPTABLES -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 222 -j ACCEPT -A INPUT -p tcp -m tcp --dport 3306 -j ACCEPT -A INPUT -j DROP -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 SYSLOG-NG destination d_iptables { file("/var/log/iptables/iptables.log"); }; filter f_iptables { facility(kern) and match("IN=" value("MESSAGE")) and match("OUT=" value("MESSAGE")); }; filter f_messages { level(info,notice,warn) and not facility(auth,authpriv,cron,daemon,mail,news) and not filter(f_iptables); }; log { source(s_src); filter(f_iptables); destination(d_iptables); };` I restart syslog-ng and the log is not written.

    Read the article

  • Keyboard mapping issue in Virtualbox on Mac OS

    - by stanleyxu2005
    I run Windows 7 as a VM in VirtualBox on my MacBook Air (using OS X 10.7). If I do not shutdown the VM but save its machine state. The keyboard will behave strangely after resuming. It seems the Windows Logo key is always hold. When I type the key 'u', the Control Panel will be shown. I tested on a real Windows 7, the same dialog will be shown when I press Win-key and 'u'. When I type the key 'e', the Explorer will show up, some as press Win-key and 'e' on a real Windows 7. If I click 'Restart' from the Start menu of Windows 7, after restarting the VM, the keyboard works again. I think there are some conflicts with keyboard driver in VM. It is quite annoying, usually I usually close a VM by saving its machine state, not shut the OS down. Is there any way to solve this problem?

    Read the article

  • Problem upgrading kernel on debian 3.1

    - by exhuma
    Hi, I have a quite old box in a remote server farm. So I have no direct access. Only remote SSH (and via SSH to a serial console). I haven't updated this box in ages. Now, whenever I want to install a new package, a dependency to glibc appears. Unfortunately, the install of glibc depends on a 2.6 kernel and I am running a venerable 2.4 kernel (one more reason to upgrade). The problem is, that the install of a new kernel has an indirect (over locales) dependency to glibc. So, to install glibc, I need a new kernel. For a new kernel, I need to upgrade glibc. Essentially I am blocked. What's the best way to proceed considering I have no "hardware" access? Here's a quick transcript of the upgrade process: [green:~]% sudo aptitude install linux-image-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages are unused and will be REMOVED: gcc-4.3-base The following NEW packages will be automatically installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 module-init-tools yaird The following packages have been kept back: adduser apache2 apache2-mpm-prefork apache2-utils apache2.2-common apt apt-utils aptitude autoconf autotools-dev awstats base-files base-passwd [...snip...] util-linux vacation vim vim-common wamerican wbritish wget whiptail whois wwwconfig-common zlib1g The following NEW packages will be installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 linux-image-686 module-init-tools yaird The following packages will be upgraded: hotplug libc6 2 packages upgraded, 8 newly installed, 1 to remove and 277 not upgraded. Need to get 0B/22.7MB of archives. After unpacking 52.1MB will be used. Do you want to continue? [Y/n/?] Writing extended state information... Done Preconfiguring packages ... (Reading database ... 34065 files and directories currently installed.) Preparing to replace libc6 2.3.6.ds1-13 (using .../libc6_2.7-18lenny2_i386.deb) ... Checking for services that may need to be restarted... Checking init scripts... WARNING: init script for postgresql not found. [ --- libc6 config screen appears here --- ] WARNING: POSIX threads library NPTL requires kernel version 2.6.8 or later. If you use a kernel 2.4, please upgrade it before installing glibc. The installation of a 2.6 kernel _could_ ask you to install a new libc first, this is NOT a bug, and should *NOT* be reported. In that case, please add etch sources to your /etc/apt/sources.list and run: apt-get install -t etch linux-image-2.6 Then reboot into this new kernel, and proceed with your upgrade dpkg: error processing /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb (--unpack): subprocess pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Ack! Something bad happened while installing packages. Trying to recover: dpkg: dependency problems prevent configuration of locales: locales depends on glibc-2.7-1; however: Package glibc-2.7-1 is not installed. dpkg: error processing locales (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: locales Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done Now, if I follow the instrunctions as promted I get the following. Note that I am using aptitude instead of apt-get to benefit from the better dependency tracking. I did try with apt-get first. But that let me to the same problem. [green:~]% sudo aptitude install -t etch linux-image-2.6.26-2-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done E: Unable to correct problems, you have held broken packages. E: Unable to correct dependencies, some packages cannot be installed E: Unable to resolve some dependencies! Some packages had unmet dependencies. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following packages have unmet dependencies: linux-image-2.6.26-2-686: Depends: initramfs-tools (>= 0.55) but it is not installable or yaird (>= 0.0.13) but it is not installable or linux-initramfs-tool which is a virtual package. Any ideas?

    Read the article

  • Unable to find valid certification path to requested target while CAS authentication

    - by Dmitriy Sukharev
    I'm trying to configure CAS authentication. It requires both CAS and client application to use HTTPS protocol. Unfortunately we should use self-signed certificate (with CN that doesn't have anything in common with our server). Also the server is behind firewall and we have only two ports (ssh and https) visible. As far as there're several application that should be visible externally, we use Apache for ajp reverse proxying requests to these applications. Secure connections are managed by Apache, and all Tomcat are not configured to work with SSL. But I obtained exception while authentication, therefore desided to set keystore in CATALINA_OPTS: export CATALINA_OPTS="-Djavax.net.ssl.keyStore=/path/to/tomcat/ssl/cert.pfx -Djavax.net.ssl.keyStoreType=PKCS12 -Djavax.net.ssl.keyStorePassword=password -Djavax.net.ssl.keyAlias=alias -Djavax.net.debug=ssl" cert.pfx was obtained from certificate and key that are used by Apache HTTP Server: $ openssl pkcs12 -export -out /path/to/tomcat/ssl/cert.pfx -inkey /path/to/apache2/ssl/server-key.pem -in /path/to/apache2/ssl/server-cert.pem When I try to authenticate a user I obtain the following exception: Caused by: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target at sun.security.provider.certpath.SunCertPathBuilder.engineBuild(SunCertPathBuilder.java:174) ~[na:1.6.0_32] at java.security.cert.CertPathBuilder.build(CertPathBuilder.java:238) ~[na:1.6.0_32] at sun.security.validator.PKIXValidator.doBuild(PKIXValidator.java:318) ~[na:1.6.0_32] Meanwhile I can see in catalina.out that Tomcat see certificate in cert.pfx and it's the same as the one that is used while authentication: 09:11:38.886 [http-bio-8080-exec-2] DEBUG o.j.c.c.v.Cas20ProxyTicketValidator - Constructing validation url: https://external-ip/cas/proxyValidate?pgtUrl=https%3A%2F%2Fexternal-ip%2Fclient%2Fj_spring_cas_security_proxyreceptor&ticket=ST-17-PN26WtdsZqNmpUBS59RC-cas&service=https%3A%2F%2Fexternal-ip%2Fclient%2Fj_spring_cas_security_check 09:11:38.886 [http-bio-8080-exec-2] DEBUG o.j.c.c.v.Cas20ProxyTicketValidator - Retrieving response from server. keyStore is : /path/to/tomcat/ssl/cert.pfx keyStore type is : PKCS12 keyStore provider is : init keystore init keymanager of type SunX509 *** found key for : 1 chain [0] = [ [ Version: V1 Subject: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5 Key: Sun RSA public key, 1024 bits modulus: 13??a lot of digits here??19 public exponent: ????7 Validity: [From: Tue Apr 24 16:32:18 CEST 2012, To: Wed Apr 24 16:32:18 CEST 2013] Issuer: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country SerialNumber: [ d??????? ????????] ] Algorithm: [SHA1withRSA] Signature: 0000: 65 Signature is here 0070: 96 . ] *** trustStore is: /jdk-home-folder/jre/lib/security/cacerts Here is a lot of trusted CAs. Here is nothing related to our certicate or our (not trusted) CA. ... 09:11:39.731 [http-bio-8080-exec-4] DEBUG o.j.c.c.v.Cas20ProxyTicketValidator - Retrieving response from server. Allow unsafe renegotiation: false Allow legacy hello messages: true Is initial handshake: true Is secure renegotiation: false %% No cached client session *** ClientHello, TLSv1 RandomCookie: GMT: 1347433643 bytes = { 63, 239, 180, 32, 103, 140, 83, 7, 109, 149, 177, 80, 223, 79, 243, 244, 60, 191, 124, 139, 108, 5, 122, 238, 146, 1, 54, 218 } Session ID: {} Cipher Suites: [SSL_RSA_WITH_RC4_128_MD5, SSL_RSA_WITH_RC4_128_SHA, TLS_RSA_WITH_AES_128_CBC_SHA, TLS_DHE_RSA_WITH_AES_128_CBC_SHA, TLS_DHE_DSS_WITH_AES_128_CBC_SHA, SSL_RSA_WITH_3DES_EDE_CBC_SHA, SSL_DHE_RSA_WITH_3DES_EDE_CBC_SHA, SSL_DHE_DSS_WITH_3DES_EDE_CBC_SHA, SSL_RSA_WITH_DES_CBC_SHA, SSL_DHE_RSA_WITH_DES_CBC_SHA, SSL_DHE_DSS_WITH_DES_CBC_SHA, SSL_RSA_EXPORT_WITH_RC4_40_MD5, SSL_RSA_EXPORT_WITH_DES40_CBC_SHA, SSL_DHE_RSA_EXPORT_WITH_DES40_CBC_SHA, SSL_DHE_DSS_EXPORT_WITH_DES40_CBC_SHA, TLS_EMPTY_RENEGOTIATION_INFO_SCSV] Compression Methods: { 0 } *** http-bio-8080-exec-4, WRITE: TLSv1 Handshake, length = 75 http-bio-8080-exec-4, WRITE: SSLv2 client hello message, length = 101 http-bio-8080-exec-4, READ: TLSv1 Handshake, length = 81 *** ServerHello, TLSv1 RandomCookie: GMT: 1347433643 bytes = { 145, 237, 232, 63, 240, 104, 234, 201, 148, 235, 12, 222, 60, 75, 174, 0, 103, 38, 196, 181, 27, 226, 243, 61, 34, 7, 107, 72 } Session ID: {79, 202, 117, 79, 130, 216, 168, 38, 68, 29, 182, 82, 16, 25, 251, 66, 93, 108, 49, 133, 92, 108, 198, 23, 120, 120, 135, 151, 15, 13, 199, 87} Cipher Suite: SSL_RSA_WITH_RC4_128_SHA Compression Method: 0 Extension renegotiation_info, renegotiated_connection: <empty> *** %% Created: [Session-2, SSL_RSA_WITH_RC4_128_SHA] ** SSL_RSA_WITH_RC4_128_SHA http-bio-8080-exec-4, READ: TLSv1 Handshake, length = 609 *** Certificate chain chain [0] = [ [ Version: V1 Subject: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country Signature Algorithm: SHA1withRSA, OID = 1.2.840.113549.1.1.5 Key: Sun RSA public key, 1024 bits modulus: 13??a lot of digits here??19 public exponent: ????7 Validity: [From: Tue Apr 24 16:32:18 CEST 2012, To: Wed Apr 24 16:32:18 CEST 2013] Issuer: CN=wrong.domain.name, O=Our organization, L=Location, ST=State, C=Country SerialNumber: [ d??????? ????????] ] Algorithm: [SHA1withRSA] Signature: 0000: 65 Signature is here 0070: 96 . ] *** http-bio-8080-exec-4, SEND TLSv1 ALERT: fatal, description = certificate_unknown http-bio-8080-exec-4, WRITE: TLSv1 Alert, length = 2 http-bio-8080-exec-4, called closeSocket() http-bio-8080-exec-4, handling exception: javax.net.ssl.SSLHandshakeException: sun.security.validator.ValidatorException: PKIX path building failed: sun.security.provider.certpath.SunCertPathBuilderException: unable to find valid certification path to requested target I tried to convert our pem certificate to der format and imported it to trustedKeyStore (cacerts) (without private key), but it didn't change anything. But I'm not confident that I did it rigth. Also I must inform you that I don't know passphrase for our servier-key.pem file, and probably it differs from password for keystore created by me. OS: CentOS 6.2 Architecture: x64 Tomcat version: 7 Apache HTTP Server version: 2.4 Is there any way to make Tomcat accepts our certificate?

    Read the article

  • How can I troubleshoot Virtualbox port forwarding from Windows guest to OSX host not working?

    - by joe larson
    There are a plethora of questions about virtual box port forwarding problems but none with my specific details. I have a Windows install living in Virtual Box, hosted within OSX. I've got several webservers running on localhost on different ports within the Windows install. I cannot for the life of me get port forwarding to work so I can access those webservers from OSX. My settings look like this (yes I have a NAT adapter): And in my vbox configuration file the relavent portion looks like this: <NAT> <DNS pass-domain="true" use-proxy="false" use-host-resolver="false"/> <Alias logging="false" proxy-only="false" use-same-ports="false"/> <Forwarding name="RLPWeb" proto="1" hostport="7084" guestip="127.0.0.1" guestport="7084"/> <Forwarding name="UtilWeb" proto="1" hostport="4040" guestip="127.0.0.1" guestport="4040"/> <Forwarding name="WCARLP" proto="1" hostport="8084" guestip="127.0.0.1" guestport="8084"/> <Forwarding name="WCAUtil" proto="1" hostport="4848" guestip="127.0.0.1" guestport="4848"/> </NAT> I've turned off the Windows firewall to ensure it is not interfering, and I am not running a firewall on OSX. Anyway, when I attempt to go to for example http://127.0.0.1:4040/ on any of my OSX browsers, it will eventually time out. The log file for this VM shows that it is correctly reading the settings and implying it's doing the right thing here: 00:00:08.286 NAT: set redirect TCP host port 4848 => guest port 4848 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 8084 => guest port 8084 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 4040 => guest port 4040 @ 127.0.0.1 00:00:08.286 NAT: set redirect TCP host port 7084 => guest port 7084 @ 127.0.0.1 00:00:08.290 Changing the VM state from 'LOADING' to 'SUSPENDED'. 00:00:08.290 Changing the VM state from 'SUSPENDED' to 'RESUMING'. 00:00:08.290 Changing the VM state from 'RESUMING' to 'RUNNING'. 00:00:08.337 Display::handleDisplayResize(): uScreenId = 0, pvVRAM=000000012017d000 w=1834 h=929 bpp=32 cbLine=0x1CA8, flags=0x1 00:00:09.139 AIOMgr: Host limits number of active IO requests to 16. Expect a performance impact. 00:00:13.454 NAT: DHCP offered IP address 10.0.2.15 I've tried setting the Host IP to 127.0.0.1, and I've tried setting Guest IP blank and also 10.0.2.15. None of these seem to help. What else can I look at to troubleshoot this issue? Details of setup: OSX 10.6.8 Windows 7 Professional 64bit VirtualBox 4.1.2

    Read the article

  • how to portforward port 7300 from server A to server B

    - by Patrick van Hout
    hi, We are using Stunnel. But want to replace it is with an iptables entry if possible. 192.168.123.122:7300 need to be forwarded to 192.168.123.188:7300. So in iptables I set these two entries: [root@dev ~]# iptables -t nat -A PREROUTING -p tcp --dport 7300 -j DNAT --to-destination 192.168.123.188:7300 [root@dev ~]# iptables -A FORWARD -m state -p tcp -d 192.168.123.188 --dport 7300 --state NEW,ESTABLISHED,RELATED -j ACCEPT But it isn't working. I did check that /proc/sys/net/ipv4/conf/eth0/forwarding has the value "1" inside. Any tips or hints? thanks, Patrick

    Read the article

  • OS X Terminal lines don't go into scrollback

    - by Steve Madsen
    I have a problem that crops up when using Mac OS X's Terminal (TERM=xterm): sometimes it gets itself into a state where lines that scroll off the top are not added to the scrollback buffer. I'm not using screen or similar; this is a plain bash shell inside a Terminal tab. It doesn't do this immediately after opening a new tab. I believe it is a side-effect of something I've run in the problem tab. My guess is that it has something to do with the xterm emulation, possibly the scroll region. What hasn't worked: Soft and hard reset via the Shell menu Running reset in the tab Is there a reliable way to reset Terminal and/or the xterm state? Can anyone provide a explanation for what's happening, even if the only fix is to close the tab and open a new one?

    Read the article

  • Hyper-v error starting vm after reboot

    - by mamu
    Hi rebooted hyper-v host running server 2008 r2. After reboot one of my vm is throwing following error. 'The version does not support this version of file format' Out of my all vms this was only set to save state when shutdown. I tried deleting state and start still same error. Tried inspect disk as well edit disk both throw same error when try to open this. What could it be? any way to resolve it?

    Read the article

  • Is It Possible to Change Default Windows Idle Time for Task Scheduler?

    - by alharaka
    From the official Microsoft docs: Detecting the Idle State The Task Scheduler service will verify that the computer is in an idle state every 15 minutes. The computer is considered idle if all the processors and all the disks were idle for more than 90% of the past 15 minutes and if there is no keyboard or mouse input during this period of time. Besides, any presentation type application that sets the ES_DISPLAY_REQUIRED flag will make Task Scheduler to not consider the system as being idle. In Windows 7, Task Scheduler considers a processor as idle even when low priority threads (thread priority < normal) execute. Is there any way to change the time to less than 15 minutes minutes? Am I assuming this hard-coded and impossible? My Google-fu has eluded me so far and I found nothing, but wanted to check here before giving up.

    Read the article

  • Ubuntu with KVM guest VM and broken bridges

    - by MadPsy
    I have an Ubuntu box with a KVM guest VM running. They use bridging so the guest VM attaches to the physical network of its host. The guest VM has 2 NICs in 2 different bridges. First NIC of the VM is tap5 and is in bridge br0 br0 8000.46720f5c572e no eth0.500 tap5 Second NIC of the VM is tap2 and is in bridge br100 br100 8000.76ad2fc96661 no eth0.100 eth0.101 eth0.103 eth0.104 eth0.105 tap2 On the host, br0 has an IP and br100 does not 21: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 46:72:0f:5c:57:2e brd ff:ff:ff:ff:ff:ff inet 192.168.100.4/24 brd 192.168.10.255 scope global br0 inet6 fe80::d6ae:52ff:febe:777/64 scope link valid_lft forever preferred_lft forever On the guest, its eth0 and eth1 interfaces both have IP addresses 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:da brd ff:ff:ff:ff:ff:ff inet 192.168.100.6/24 brd 192.168.100.255 scope global eth0 inet6 fe80::23e:61ff:fefb:7ada/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 00:3e:61:fb:7a:ea brd ff:ff:ff:ff:ff:ff inet 172.16.50.129/25 brd 172.16.50.255 scope global eth1 inet6 fe80::23e:61ff:fefb:7aea/64 scope link valid_lft forever preferred_lft forever On the guest VM, a tcpdump of its eth1 interface (tap2) shows traffic from its eth0 interface (tap5), as if the 2 bridges are themselves bridged. This means any interface on br100 is now bridged across to br0 - which is completely broken. root@chillispot:~# tcpdump -c 1 -n -v -i eth1 net 192.168.100.0/24 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 65535 bytes 16:31:24.175583 IP (tos 0x0, ttl 64, id 48054, offset 0, flags [DF], proto TCP (6), length 148) 192.168.100.6.22 > 192.168.100.4.59505: Flags [P.], cksum 0x6c2b (correct), seq 1056321648:1056321744, ack 398642983, win 1700, options [nop,nop,TS val 197473436 ecr 200655363], length 96 What could be bridging the 2 bridges, except the guest VM (which is a stock Ubuntu install)? I am at a complete loss! Thanks.

    Read the article

  • DELL DRAC & Ubuntu VPN Connection

    - by Mikunos
    I am trying to connect to a DELL DRAC card without success by Ubuntu VPN Connection Manager. I have these data: Protocol: PPTP SERVER IP PPTP: 1233.123.123.123 DRAC IP: 192.168.10.25 Subnet: 255.255.0.0 User: myuser Pass: mypass where have I to write these parameters? I have configured the PPTP connection using the graphical tool in Ubuntu 11.10 ... but in the /var/log/syslog I get these messages: Apr 15 11:33:15 shinet NetworkManager[1035]: <info> Starting VPN service 'pptp'... Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 18180 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN service 'pptp' appeared; activating connections Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN plugin state changed: 3 Apr 15 11:33:15 shinet NetworkManager[1035]: <info> VPN connection 'Connessione VPN 1' (Connect) reply received. Apr 15 11:33:15 shinet pppd[18182]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Apr 15 11:33:15 shinet pppd[18182]: pppd 2.4.5 started by root, uid 0 Apr 15 11:33:15 shinet pppd[18182]: Using interface ppp0 Apr 15 11:33:15 shinet pppd[18182]: Connect: ppp0 <--> /dev/pts/1 Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:15 shinet NetworkManager[1035]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. Apr 15 11:33:15 shinet pptp[18185]: nm-pptp-service-18180 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Apr 15 11:33:46 shinet pppd[18182]: LCP: timeout sending Config-Requests Apr 15 11:33:46 shinet pppd[18182]: Connection terminated. Apr 15 11:33:46 shinet avahi-daemon[1081]: Withdrawing workstation service for ppp0. Apr 15 11:33:46 shinet NetworkManager[1035]: SCPlugin-Ifupdown: devices removed (path: /sys/devices/virtual/net/ppp0, iface: ppp0) Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:46 shinet pppd[18182]: Modem hangup Apr 15 11:33:46 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet pppd[18182]: Exit. Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> VPN plugin failed: 1 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state changed: 6 Apr 15 11:33:51 shinet NetworkManager[1035]: <info> VPN plugin state change reason: 0 Apr 15 11:33:51 shinet NetworkManager[1035]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active. Apr 15 11:33:51 shinet NetworkManager[1035]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Apr 15 11:33:57 shinet NetworkManager[1035]: <info> VPN service 'pptp' disappeared Thanks

    Read the article

  • How can I install my installed linux on another hardware too?

    - by donamir
    Hi. It's my state: I installed some apps on a linux server(ubuntu). Apps stack are development tools: -some of Atlassian product -SVN, USVN -Maven, Artifactory -Tomcat & ... My problem: I want to create a bootable dvd to be able to restore same state(OS, configuration and apps) on another hardware(server). Some notes: I prefer ubuntu but my linux can be a different distributions if needed. w I prefer final result (bootable dvd) be simple and easy to use as installing a linux(ubuntu). I prefer a bootable DVD but if it's not possible, any other solution like partial backup/package even if needed to install first OS and then apply the package/backup/... can be good. Finally: Thanks in advance.

    Read the article

  • Is there analog of aticonfig --set-powerstate for open source radeon driver?

    - by vava
    I'm running Ubuntu 9.04 on relatively old laptop with ATI Mobility x600 inside. On the last version of Ubuntu, when I was able to run proprietary fglrx driver, I was able to slow down graphic card by aticonfig --set-powerstate 1 and save some battery charge. Now I forced to run open source driver as ATI decided to drop support for old cards. But I can't find a way to control power states now except relying on DynamicClocks option in xorg.conf. But I really know better when and what powerstate I want, so is there a tool that let me change power state manually or at least let me somehow change the behavior of automatic power state selection?

    Read the article

  • Any way to know what files were in a broken ZFS pool?

    - by Erik Tjernlund
    I have a large ZFS pool of 4 combined drives. Now, the filesystem can not be mounted: pool: tank state: UNAVAIL status: One or more devices could not be opened. There are insufficient replicas for the pool to continue functioning. action: Attach the missing device and online it using 'zpool online'. see: http://www.sun.com/msg/ZFS-8000-3C scan: none requested config: NAME STATE READ WRITE CKSUM tank UNAVAIL 0 0 0 insufficient replicas c10t0d0 ONLINE 0 0 0 c8t0d0 UNAVAIL 0 0 0 cannot open c8t1d0 ONLINE 0 0 0 c10t1d0 ONLINE 0 0 0 Probably a broken drive (c8t0d0). I'm not overly concerned by the loss of the data, but I'd love to know exactly which files were in that pool. Is there any way to get a listing of what files were there?

    Read the article

< Previous Page | 126 127 128 129 130 131 132 133 134 135 136 137  | Next Page >