Search Results

Search found 4073 results on 163 pages for 'hosts deny'.

Page 131/163 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

• Samba and Windows 7

  - by John Gaughan

  I built a new computer with the intention of it being primarily a home file server. Here is my setup: one desktop with Windows 7 64 HP one laptop with Windows 7 64 HP one desktop with Kubuntu 11.10 (server) The two desktops use static IPs, and I have hostnames mapped in the HOSTS files on all three systems. I have the same username/password combo on all three systems. I have been trying for a while now to set up Samba so the Windows 7 systems can see and use it. Even if I can get the server to show up, Windows is unable to log in. One of the first things I did was to enable LMv2 authentication, which this version of Samba (3.5.11) supports. The workgroup is set correctly. I can normally see the server, but cannot authenticate. Windows homegroup is turned off. Pinging between machines works fine, and the two Windows 7 systems work together flawlessly. What I am trying to do is set up Samba to use peer to peer networking using NTLM security and user-mode authentication. According to the documentation this is possible, but there are no examples that I could find. In all the googling I have done, I see a lot of people asking how to set this up but it either works for someone else and not for me (no idea what I'm missing), or it doesn't work. Has anyone gotten this to work? Is there a place I could download a smb.conf that is set up to work in this environment?

  Read the article

• Debian Linux bridging router intermittently dropping packets [migrated]

  - by nomen

  My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Can anybody help?

  Read the article

• Configure an Azure VM for Dynamic DNS for Cloud Services

  - by Adam

  I am trying to setup an azure VM with proper DNS to allow multiple cloud services to communicate across cloud service boundaries. As I understand it, I need to provide my own DNS server. I do not have any on-premise infrastructure, so I am trying to configure an Azure VM to act as my DNS. This SO question (http://stackoverflow.com/questions/21858926/azure-how-to-connect-one-cloud-service-with-other-in-one-virtual-network) is very similar to my setup. This article (http://msdn.microsoft.com/en-us/library/windowsazure/jj156088.aspx) describes my particular case: Name resolution between virtual machines and role instances located in the same virtual network, but different cloud services Here is what I have done: Created Azure Virtual Network and declared subnets for each of my cloud services. Created an Azure VM (Windows 2012 R2) with DNS enabled RDP to the VM and enabled the DNS role and installed features Added the appropriate NetworkConfiguration xml section to each of my cloud services .csfg files Re-deployed my cloud services I have verified that I setup the virtual network and networkconfiguration properly because my cloud service hosts are able to communicate with each other if I use the internal ips. However, name resolution doesn't appear to be working, and it doesn't appear that my cloud service roles can communicate with my DNS server. How do I configure my VM so that my different cloud services roles register themselves with my DNS server? EDIT: I think I am 1 step closer to getting this to work. The cloud services that I was using are in an old affinity group which is not supported by VMs, so I was unable to add my VM into my virtual network. I created a new VNET in a new affinity group with my VM added into it. However, I still don't know how to configure the azure VM's DNS server so that the cloud services register themselves for name resolution. Also, an added bonus guaranteed to get a +1 would be to explain if it is possible to register a DNS entry for the VIP for an internal endpoint of my cloud services so we can get load balancing. Thanks!

  Read the article

• Apache debugging: where to find error logs?

  - by AP257

  I'm new to Apache and web serving generally, so apologies if this is a very stupid question. I want to configure a new sub-domain on a working site and install a forum there. I'm using a Debian server that already has Apache, mod_wsgi and a bunch of virtual hosts successfully running on it. I first installed my forum app (Django's OSQA). Following the OSQA instructions, I then created an Apache config file that specified ServerName as the new sub-domain. I also created a .wsgi file for the app, and pointed WSGIScriptAlias at it. I then restarted Apache. However, when I go to the new sub-domain, I get a 404 error message. Two questions: Is there a step missing above? Or is simply creating a new Apache config file in sites-available enough to 'tell' Apache about a new sub-domain? If there's something else going wrong, how can I debug it? The ErrorLog and CustomLog specified in the config file are both blank. apache2.conf, which I guess is Apache-wide configuration, specifies ErrorLog /var/log/apache2/error.log, but this is yet another blank file.

  Read the article

• Registering publicly Mail server and Web server in a free dns server

  - by Bruno Vieira

  I'm trying to host the e-mails and the site of our company into our private server. I've already followed the Gentoo Virtual Mailhosting System with Postfix Guide and my mail server is working (actually it sends mails for the local users and for external users it goes to spam) and know how to set an Apache 2 server. What I don't know (and I mean really don't) is how to make them public. I did some research and found that I should ask my ISP to change the reverse DNS to my company domain in order to prevent my mails to be marked as spam, they are doing. I already know I have to configure a DNS Server, it seems like my register provider already has one but I don't know how I can configure CNET, A, MX, TXT and all those tags (Is it tags the name?) and If I must do some other configuration on my server. My Server: Linux mail 3.2.21-gentoo #1 SMP My /etc/hosts: 127.0.0.1 mail.example.com.br example example.com.br ::1 mail.example.com.br mail example.com.br My /etc/conf.d/hostname: hostname ="mail" What am I missing? If there's a guide about how to configure I would really be grate. Thanks in advance for the help. Cheers

  Read the article

• PNP4Nagios, nagiosgraph, separate Cacti, or something else for Nagios trending

  - by Matt

  I've been using Nagios for a while now and recently started using Cacti after being dissatisfied with the lack of scaling and lack of any GUI in MRTG. I'm interested in adding trending to my Nagios installation and wondered what was the best route to go. I've looked around a bit and have seen what's available, but there's not a lot of information around to differentiate them from each other. My Nagios install has about 250 hosts and 1100 service checks, but many of them are just simple network devices and there's only about 20 servers and 300 services associated with them. All servers but 2 are running Windows Server 2003. What are the main highlights of PNP4Nagios vs. nagiosgraph, or would I be better off using some sort of tool to convert the data to RRD form and just view it directly in Cacti? Is there a completely different direction I could go that would be even better? Please comment if you need any more information, I tend to be too wordy and tried to keep this question brief. Thanks!

  Read the article

• Mysql can not resolve hostnames when checking privileges

  - by Fabio

  I'm going crazy to solve this. I have a mysql installation (on machine db.example.org) which doesn't resolve a given hostname. I gave privileges using hostnames i.e. GRANT USAGE ON *.* TO 'user'@'host1.example.org' IDENTIFIED BY PASSWORD 'secret' GRANT SELECT, INSERT, UPDATE, DELETE, CREATE, INDEX ON `my_database`.* TO 'user'@'host1.example.org' However when I try to connect using mysql -u user -p -h db.example.org I obtain ERROR 1045 (28000): Access denied for user 'user'@'192.168.11.244' (using password: YES) I already checked for correct name resolution in the dns system: $ dig -x 192.168.11.244 ;; ANSWER SECTION: 244.11.168.192.in-addr.arpa. 68900 IN PTR host1.example.org. I've also checked for skip-name-resolve option in mysql variables in fact if I can access from another machine on the same subnet using hostname privileges. The only difference is that host1.example.org and db.example.org point the same ip on the same machine i.e. both db.example.org and host1.example.org have ip 192.168.11.244. In this way all the applications using that database can use the name db.example.org and we can move the data on other hosts (if needed) just by changing the dns record, leaving the application code unchanged. What should I do to solve this or at least to understand what's happening?

  Read the article

• exim4 redirect mail sent to *@domain1.example.com to *@domain2.example.com

  - by nightcoder

  Current situation: We have a VPS that hosts a website example.org. Exim is configured to work as a smarthost. All emails sent through exim are successfully relayed to another mail server (that is working on example.com). Goal: To forward mail sent to *@example.org to *@example.com, i.e. change the recipient's address from *@example.org to *@example.com. Problem: If I send email to address *@example.org, then it seems exim doesn't change the address, it still relays the message to another mail server but recipient is still *@example.org. Maybe the redirect is not applied for some reason. Configuration and logs: /etc/exim4/update-exim4.conf.conf: dc_eximconfig_configtype='smarthost' dc_other_hostnames='' dc_local_interfaces='' dc_readhost='example.org' dc_relay_domains='example.org' dc_minimaldns='false' dc_relay_nets='0.0.0.0/32' dc_smarthost='example.com::26' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='true' dc_mailname_in_oh='true' dc_localdelivery='maildir_home' /etc/exim4/conf.d/router/999_exim4-config_redirect (created by me): domain_redirect: debug_print = "R: forward for $local_part@$domain" driver = redirect domains = example.org data = [email protected] (for now data is set to a specific address for simplicity and testing) exim log when sending email to [email protected] (should be redirected to [email protected]): 2012-03-20 19:40:07 1SA4ud-0005Dw-7k <= [email protected] U=www-data P=local S=657 2012-03-20 19:40:08 1SA4ud-0005Dw-7k => [email protected] R=smarthost T=remote_smtp_smarthost H=domain2.com [184.172.146.66] X=TLS1.0:RSA_AES_256_CBC_SHA1:32 DN="C=US,2.5.4.17=#13053737303932,ST=TX,L=Houston,STREET=Suite 400,STREET=11251 Northwest Freeway,O=HostGator.com,OU=HostGator.com,OU=Comodo PremiumSSL Wildcard,CN=*.hostgator.com" 2012-03-20 19:40:08 1SA4ud-0005Dw-7k Completed So, the address is not changed :( Please help! I'm trying to make it work for half a day already :(

  Read the article

• vmware vcenter 5.1 installation with FQDN error

  - by CSG

  I'm trying to install vCenter 5.1 on a windows 2012 dedicated (with SQL express standalone) During the installation of the Single Sign On module i've a warning "the fully qualified domain name cannot be resolved with nslookup. if you continue the installation some features might not work correctly. for detailed requiments see the installation and setup guide" The only indication that i've found are about the reverse zone dns resolution.. and this works! i've verified that the dns works properly with nslookup C:\Users\admin>nslookup srv6.mydomain.local Server: srv2.mydomain.local Address: 172.25.4.22 Nome: srv6.mydomain.local Address: 172.25.1.26 C:\Users\admin>nslookup 172.25.1.26 Server: srv2.mydomain.local Address: 172.25.4.22 Nome: srv6.mydomain.local Address: 172.25.1.26 (all ip are right: I've the vCenter=srv6 and DC+DNS=srv2 on different vlan) i've tryed to force the resolution of the ip changing the [..]\drivers\etc\hosts file i've disabled the IPv6 support i've used all combination with domain prefixes (explicit, by dhcp, undefined..) i've disabled all antivirus/firewall (kaspersky end point 10) is this a bug of vcenter 5.1.0-1065152 ? have you got any suggestions for me?

  Read the article

• Problems starting autossh on boot [ubuntu]

  - by Ken

  I'm trying to automatically start an SSH tunnel to my server on boot from a ubuntu box. I have an ubuntu box that's mounted on an 18-wheeler and is networked behind an air card. The box hosts a mysql database that i'm trying to have replicated when the aircard is connected. As I can never be sure of my IP and how many or which routers I'm behind I'm connected to my replication server with an SSH tunnel. I got that working using the following command: ssh -R 3307:localhost:3307 [email protected] Now I'd like that to start whenever the box is, and be alive all the time, so I installed auto-ssh and setup this little script: ID=xkenneth HOST=erdosmiller.com AUTOSSH_POLL=15 AUTOSSH_PORT=20000 AUTOSSH_GATETIME=30 AUTOSSH_DEBUG=yes AUTOSSH_PATH=/usr/bin/ssh export AUTOSSH_POLL AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -fN -M 20000 -R 3307:localhost:3306 ${ID}@${HOST} I've tried putting this scrip in /etc/init.d/ and using a post-up command in /etc/network/interfaces as well as putting it in /etc/network/if-up.d/. In both situations the script starts on boot, but the tunnel doesn't appear to be correctly established. The script works when run manually.

  Read the article

• Thunderbird alerts when expected email does not arrive

  - by user871199

  I am on Ubuntu 12.04 using Thunderbird as email client. Both are up to date in terms of updates. I have bunch of nightly jobs that do the work and send a status mail. It gets tedious if you keep getting same/similar mails every day so I ended up writing a mail filter rule which causes emails to end up in their respective folders automatically. If things are going ok, I really don't need to read emails. Failure emails are sent to different alias - if the job runs. We recently discovered that one of the job had not run for few days as someone accidentally disabled it. In order to avoid such problems in future, I would like to setup thunderbird in such a way that if I don't get email from given address within given duration, it should alert me. My dream solution is to set up frequency - some jobs do run every 4 hours. Is this possible? Can I setup Thunderbird (preferred) or other email client for reminding me when expected email does not show up. Based on comments and answer I received, here are the reasons why I would like to use Thunderbird. We are already using Thunderbird. It has calender support via plugin, so I suppose someone is already watching time to remind us about the event. May be this another type of event. Additional job is one more failure point, may complicate life if it has to monitor multiple hosts. Additional tools - same thing, one more failure point. Thunderbird can be run across all the platforms we are using - Windows and Ubuntu. It sort of becomes platform independent solution.

  Read the article

• SpamAssassin bayesian score discrepancies

  - by CaptSaltyJack

  This makes my brain hurt. For some reason, SpamAssassin is giving high scores to certain emails, but when I test them on the command line, they get a low score. This one particular email has this in the header: X-Spam-Flag: YES X-Spam-Score: 8.521 X-Spam-Level: ******** X-Spam-Status: Yes, score=8.521 tagged_above=-9999 required=5 tests=[BAYES_99=3.5, BAYES_999=0.2, HTML_MESSAGE=0.001, NO_RECEIVED=-0.001, NO_RELAYS=-0.001, RAZOR2_CF_RANGE_51_100=0.5, RAZOR2_CF_RANGE_E8_51_100=1.886, RAZOR2_CHECK=0.922, URIBL_RHS_DOB=1.514] autolearn=no Yet when I dump the raw email into a file msg and run sudo su amavis -c 'spamassassin -t msg', I get this output: Content analysis details: (3.8 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- 1.5 URIBL_RHS_DOB Contains an URI of a new domain (Day Old Bread) [URIs: cliobeads.com] -1.0 ALL_TRUSTED Passed through trusted hosts only via SMTP 0.0 HTML_MESSAGE BODY: HTML included in message -0.0 BAYES_20 BODY: Bayes spam probability is 5 to 20% [score: 0.1855] 1.9 RAZOR2_CF_RANGE_E8_51_100 Razor2 gives engine 8 confidence level above 50% [cf: 100] 0.5 RAZOR2_CF_RANGE_51_100 Razor2 gives confidence level above 50% [cf: 100] 0.9 RAZOR2_CHECK Listed in Razor2 (http://razor.sf.net/) I'm really confused as to why when the email comes in, it gets a completely different score attached to it than when I run spamassassin -t. Is there some other way I should be testing emails? Also, my users have the ability to drag false positives into a folder called "False Positives," and every day a cron job fires off that runs this on every message in every user's folder: sa-learn --dbpath=/var/lib/amavis/.spamassassin --ham /tmp/*-*.eml >/dev/null I ran sudo locate bayes_toks and there's definitely only one bayes DB on the system, in /var/lib/amavis/.spamassassin. I'm clueless, any help would be great and may help restore my sanity!

  Read the article

• ProCurve 1800 switch issue

  - by user98651

  I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

  Read the article

• Why can't I unblock postgres with shorewall?

  - by ryeguy

  I can't seem to unblock the port needed for postgres using Shorewall. I am developing a PHP app on my windows machine here, and then I upload it on my linux box to actually use it. The linux box runs the php files as well as hosts the db server. Since I need it working from both machines, in my PHP code I am referring to the database as the full IP instead of localhost. I can easily connect to postgres from my windows machine, but ironically, my PHP app can't connect to postgres even though it's on the same box. Here's what I have in /etc/shorewall/rules: #macro/action src dest PostgreSQL/ACCEPT net $FW PostgreSQL/ACCEPT loc $FW PostgreSQL/ACCEPT loc dmz PostgreSQL/ACCEPT net dmz PostgreSQL/ACCEPT loc net PostgreSQL/ACCEPT dmz $FW PostgreSQL/ACCEPT dmz loc PostgreSQL/ACCEPT dmz net PostgreSQL/ACCEPT dmz dmz Clearly I have a ton of crap there. The first line is all I needed to make it allow a connection from my windows machine. All the lines after it are me just trying everything to get it to work. What am I missing?

  Read the article

• Running DNS locally for home network

  - by Roy Rico

  I have a small home network that just got larger ( New roommate, My existing roommate got a laptop (on top of her computer)j, my friends coming over with laptop, etc ). I'd like to run a local DNS server for lookups of my local network stuff (fileserver.local, windowsTV.local, machineA.local, machineB.local, appletv.local). I used to have a business line with a static IP, and run bind/named internally. However, now, I have a normal account. My ISP's DNS servers are constantly changing (for whatever reasons my ISP doesn't like to keep the same IP range for long). I need my local DNS to be automatically updated to use my ISP's DNS for external traffic, but be able to maintain an internal DNS server (getting to update the hosts file is being a hassle with every new machine on top of rebuilding existing machines with win7 or Ubuntu 9.04). Additionally, My ISP's DNS servers often crash or become unresponsive. Are there any open DNS servers that are reliable (i don't want to reconfig every day) that I could use as my primary, then if those fail, then use my ISP's? UPDATE: Also looking for each workstation to be able to use dhcp to connect, but instead of getting ISP dns servers, getting my internal one.... Thanks

  Read the article

• Linux (DUP!) ping packages

  - by Darkmage

  i cant seem t figure out what is going on here. The Linux machine I am using is running as a VM on a Win7 machine using Virtual Box running as a service. If i ping the win7 Host i get ok result. root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.100 PING 192.168.1.100 (192.168.1.100) 10(38) bytes of data. 18 bytes from 192.168.1.100: icmp_seq=1 ttl=128 time=1.78 ms 18 bytes from 192.168.1.100: icmp_seq=2 ttl=128 time=1.68 ms if i ping localhost im ok root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 localhost PING localhost (127.0.0.1) 10(38) bytes of data. 18 bytes from localhost (127.0.0.1): icmp_seq=1 ttl=64 time=0.255 ms 18 bytes from localhost (127.0.0.1): icmp_seq=2 ttl=64 time=0.221 ms but if i ping gateway i get DUP packets root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 10(38) bytes of data. 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.27 ms 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.46 ms (DUP!) 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.1 ms 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.4 ms (DUP!) if i ping other machine on same LAN i stil get dups. pinging remote hosts also gives (DUP!) result root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 www.vg.no PING www.vg.no (195.88.55.16) 10(38) bytes of data. 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.0 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.3 ms (DUP!) 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.3 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.6 ms (DUP!)

  Read the article

• What is the minimal steps to setup a client-server network using Windows Server 2008 R2 standard?

  - by Motivated Student

  Background I have One computer server with Win Server 2008 R2 standard installed but it has not been configured. This server has 2 LAN adapters. One adapter is connected to ISP and the other one connected to HUB/Switch. Other computers working as clients are connected to the same HUB/Switch to which the server is connected. IP Printers, IP scanners, IP camera are also connected to the same HUB/Switch. Note: I am a newbie. I only know how to plug RJ-45 sockets and assembly computer peripherals. I have no prior experience in Windows Server at all. Please teach me from the newbie's point of view. Objective I want to establish the following: Each client can access the internet, printers, scanners after it has been successfully authenticated by the server. Unauthenticated clients cannot access the internet, printers, etc. The server hosts a local site. Clients can browse internally using a private domain www.company.com. If the same domain name has been used by other on the internet, my private domain must override the public domain.

  Read the article

• emacs error: "Symbol's value as variable is void: hostname"

  - by Florian Pilz

  After I installed emacs this error occurs every time on startup. It prevents me from installing plugins, e.g. auctex via aptitude. I already tried to install a plugin by hand (rails for ruby), but doesn't work. The error doesn't contain the message "hostname", but the hostname of my PC is displayed ("bloodredangel-ubuntu"). I changed my hostname to "bloodredangel", but the error message stays the same. While I changed my hostname I saw that in /etc/hostname were two entries: 127.0.0.1 bloodredangel-ubuntu I already asked this question in an ubuntu forum but they couldn't help. They recognised an misconfigured /etc/hosts file, which I corrected, but from time to time these incorrect configurations get attached by something. I didn't add them by hand, maybe it has something to do with the issue. The misconfigurations looked like this: 127.0.0.1 127.0.0.1 bloodredangel-ubuntu localhost.localdomain localhost 127.0.0.1 127.0.0.1:8080 bloodredangel-ubuntu localhost.localdomain localhost I didn't found a solution on the internet, so I hope I will find help here finally.

  Read the article

• How Do I Secure WordPress Blogs Against Elemento_pcx Exploit?

  - by Volomike

  I have a client who has several WordPress 2.9.2 blogs that he hosts. They are getting a deface kind of hack with the Elemento_pcx exploit somehow. It drops these files in the root folder of the blog: -rw-r--r-- 1 userx userx 1459 Apr 16 04:25 default.htm -rw-r--r-- 1 userx userx 1459 Apr 16 04:25 default.php -rw-r--r-- 1 userx userx 1459 Apr 16 04:25 index.asp -rw-r--r-- 1 userx userx 1459 Apr 16 04:25 index.aspx -rw-r--r-- 1 userx userx 1459 Apr 16 04:25 index.htm -rw-r--r-- 1 userx userx 1459 Apr 16 04:25 index.html -rwxr-xr-x 1 userx userx 1459 Apr 16 04:25 index.php* It overwrites index.php. A keyword inside each file is "Elemento_pcx". It shows a white fist with a black background and the phrase "HACKED" in bold letters above it. We cannot determine how it gets in to do what it does. The wp-admin password isn't hard, but it's also not very easy either. I'll change it up a little to show you what the password sort of looks like: wviking10. Do you think it's using an engine to crack the password? If so, how come our server logs aren't flooded with wp-admin requests as it runs down a random password list? The wp-content folder has no changes inside it, but is run as chmod 777 because wp-cache required it. Also, the wp-content/cache folder is run as chmod 777 too.

  Read the article

• Rundeck get verbose output of command executing on node

  - by Leon Stafford

  I have Rundeck executing a remote script, which is in python is using print statements to return output normally such as: $ python mytest.py PASS: Condition 1 passed PASS: Condition 2 passed PASS: and so on... When I run this via Rundeck, however, it doesn't show me the same print generated outputs as above. In Rundeck's most detailed Debug output mode, I only receive the following: 06:31:12 Permanently added 'myremotenode.com' (RSA) to the list of known hosts. 06:31:12 SSH_MSG_NEWKEYS sent 06:31:12 SSH_MSG_NEWKEYS received 06:31:12 SSH_MSG_SERVICE_REQUEST sent 06:31:13 SSH_MSG_SERVICE_ACCEPT received 06:31:13 Authentications that can continue: publickey,password,keyboard-interactive 06:31:13 Next authentication method: publickey 06:31:13 Authentication succeeded (publickey). 06:31:13 /cygdrive/c/Program Files (x86)/Mozil... 06:32:06 Adding reference: ant.PropertyHelper 06:32:06 Setting project property: sshexec.output -> /cygdrive/c/Prog... I know that the remote script is actually executing just as usual, as I'm receiving other emails generated by the ~30min long script. Obviously, I don't want to have to wait 30mins to see the result of each print statement within the python script. How can I get the same level of output in Rundeck as I do in the bash shell directly?

  Read the article

• How can I manage AWS VPC ssh access accounts and keys across multiple instances?

  - by deitch

  I am setting up a standard AWS VPC structure: a public subnet some private subnets, hosts on each, ELB, etc. Operational network access will be via either an ssh bastion host or an openvpn instance. Once on the network (bastion or openvpn), admins use ssh to access the individual instances. From what I can tell all of the docs seem to depend on a single user with sudo rights and a single public ssh key. But is that really best practice? Isn't it much better to have each user access each host under their own name? So I can deploy accounts and ssh public keys to each server, but that rapidly gets unmanageable. How do people recommend managing user accounts? I've looked at: IAM: It doesn't like like IAM has a method for automatically distributing accounts and ssh keys to VPC instances. IAM via LDAP: IAM doesn't have an LDAP API LDAP: set up my own LDAP servers (redundant, of course). Bit of a pain to manage, still better than managing on every host, especially as we grow. Shared ssh key: rely on the VPN/bastion to track user activities. I don't love it, but... What do people recommend? NOTE: I moved this over from accidentally posting in StackOverflow.

  Read the article

• sendmail relay status

  - by Andy

  Hello all, I have a RHEL3 server with sendmail configured to relay mail to: # "Smart" relay host (may be null) DSmailrelay This relay server is an exchange server not administered by me. A few days ago its IP address was changed without my knowledge so I've updated the correct ip in /etc/hosts for the mail relay entry. Unfortunately no mail is currently going through and maillog reports: Oct 26 14:32:39 fsimag sendmail[12580]: n9Q3VxPA012580: from=root, size=3685, class=0, nrcpts=1, msgid=<~R.*.2009102614315955@*>, relay=root@localhost Oct 26 14:32:39 fsimag sendmail[12580]: n9Q3VxPA012580: to=wodwest@*.net, delay=00:00:40, mailer=esmtp, pri=33685, dsn=4.4.3, stat=queued Oct 26 14:36:09 fsimag sendmail[13670]: n9Q3ZTcf013670: from=root, size=5831, class=0, nrcpts=1, msgid=<~R.medicus.2009102614352914@*>, relay=root@localhost Oct 26 14:36:09 fsimag sendmail[13670]: n9Q3ZTcf013670: to=tsgastro@(.net, delay=00:00:40, mailer=esmtp, pri=35831, dsn=4.4.3, stat=queued Oct 26 14:36:50 fsimag sendmail[13882]: n9Q3aAxj013882: from=root, size=5830, class=0, nrcpts=1, msgid=<~C.medicus.2009102614361009@*>, relay=root@localhost Oct 26 14:36:50 fsimag sendmail[13882]: n9Q3aAxj013882: to=elmwood@*.net, delay=00:00:40, mailer=esmtp, pri=35830, dsn=4.4.3, stat=queued (With domains obscured) The mailq command shows nothing, and I've also tried connecting to this new mail server via telnet and manually sending and reports as being queued but not sent. The administrator of this machine has put it back to me saying he sees no problems, and I just want to cover everything before passing it back to him. Is there any other tests/logs/reasons for sendmail to only report it as "stat=queued" ? I've looked in previous logs and the relay is set to root@localhost in those but none were ever set to queued. Thanks for any help, Andy

  Read the article

• How can I split 200Mbps of streaming traffic into routers?

  - by Jared

  As the title says, I have 200Mbps of streaming video traffic coming into my command center. How do I split the load between routers? Setup is like this: fiber --- router --- switch --- workstations I'm sorry I haven't dealt with this much traffic before. so please be gentle if you're going to kick me out :) EDITED FOR DETAILS: Okay, this specific project is for our company's IP CCTV system. We have deployed over 100++ cameras all over a building/campus and we have estimated each camera to take about 2Mbps of bandwidth each. Now, they're all connected to a switch and that's entirely fine. But coming into our command center, they have to be on a router since it'll get more than 200++ cameras next year (and I don't want to have too many hosts on one subnet). My plan was to have the 1st hundred on a 172.16.9.x block and the 2nd hundred on a 172.16.10.x block (all /24). The servers I have are currently sized to match (about 5 dual 6-core xeons) and I'd have about 19 workstations all streaming video from the 5 servers. (servers pull video from the cameras). But 200Mbps of constant traffic? How the hell do I even break this up? I need to have 1 gateway, to manage the routes... I honestly think I'm way in over my head.

  Read the article

• Varnish configuration, NamevirtualHosts, and IP Forwarding

  - by Brent

  I currently have a bunch of NameVirtualHost based websites, load balanced between 3 apache2 servers using ldirectord. I would like to insert varnish as a reverse-web-proxy between ldirectord and apache in the following way: a request comes in to ldirectord it is then load balanced between the 3 apache2 servers and varnish, with a weight of 1 for the webservers, and 99 for varnish (so if varnish is rebooted, the webservers will take over seamlessly) varnish will then load balance its requests between my apache2 servers. However, the varnish part is not working. I wonder whether this has to do with the fact that my apache servers use x.x.x.x:80 for their NameVirtualHosts, instead of *:80? (they have to do this, since each server hosts multiple IP addresses) Or perhaps it has to do with the need for IP Forwarding to be set up on the varnish server? (I did echo 1 /proc/sys/net/ipv4/ip_forward on this server, is that sufficient?) How can I debug this problem? ldirectord doesn't produce logs of what it does with each request (and if it did, I would be overwhelmed with information since I'm serving hundreds of requests per second) varnish log shows the ldirectord server connecting to it every 5 seconds, but nothing else. I have set up a test site using this configuration, but it fails - no apache access logs, no applicable varnish logs.

  Read the article

• Split horizon, route filtering, and having RIPv2 announce a non-attached route to host...

  - by Paul

  Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

  Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >