Search Results

Search found 9611 results on 385 pages for 'low power'.

Page 131/385 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

• ASP.NET Session State SQL Server 2008 R2 Freezes with High CPU Usage

  - by jtseng

  Our ASP.Net website uses SQL Server as the session state provider. We currently host the database on SQL Server 2005 since it does not play well on 2008 R2. We would like to know why, and how to fix it. hardware setup Our current session state server has SQL Server 2005 with the files hosted on a single local disk. It is one of our oldest servers since it has served us well, and we never felt the need to upgrade it. The database is about 2 GB holding 6000 sessions. (The sessions are a little big, but we need it.) We have another server with SQL Server 2008 R2 with a much faster CPU, much more RAM, and a much faster hard disk. situation One day, we have a huge surge in traffic. The transaction log growth on SQL Server freezes the server for 10's of seconds, allowing only a few requests through in minutes. So we load up the new server with ASPState with very large data and log files and point all of our applications to the new server. It chugs along fine for about 5 minutes, and then the CPU usage jumps up to 50% of the 16 cores that Standard Edition can use and freezes for 10's of seconds at a time. The files do not record any autogrowth events. The disk queue is nice and low. RAM usage is low. CPU usage on our old server has never been higher than 5%. What happened on the new server? Alternatively, I would like to hear success stories with ASP.NET session state server running on SQL Server 2008 R2 with an average write load of 30MB/sec with bursts up to 200MB/sec.

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• Is there a realiable way to troubleshoot wake up from sleep in Windows?

  - by Borek

  Is there a reliable way to troubleshoot laptop wakes? I've seen "heuristics" posted here and there but isn't there really a simple and deterministic way to tell what's causing a problem? Specifically, my laptop wakes up about every hour for about 2 minutes. Exported event log entries are here: http://www.mediafire.com/?abcqb00v5wyo6pj. I've tried: powercfg -devicequery wake_armed Empty result set. Scheduled tasks - the main ones are not scheduled to run every hour. When go through a long list of all possible tasks, there are some that are set to be triggered every hour (e.g., MS "RacTask" whatever it is). But when I go to power options, Advanced settings, Sleep, Allow wake timers it is set to "Disable". Also, the specific task is not set to wake the computer if necessary. Power options for my Ethernet card don't enable it to wake the computer - the cable is disconnected anyway. There are no other HW devices attached - no USB disks, no keyboards / mice etc. I am really clueless and quite unhappy that it's so hard to troubleshoot this situation.

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• Wake-on-lan only works so many times

  - by Chance

  I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

  Read the article

• Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

  - by ZiGi

  i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

  Read the article

• Sudden and frequent hangs on desktop computer: mobo or CPU fault?

  - by djechelon

  I have a desktop computer equipped with an ASUS Crosshair 2 Formula and a Phenom x6 3.2GHz CPU. My problem is that often the computer will hang all of a sudden, completely stopping responding. When that occurs, reset key is inoperative and power button turns the computer off but is unable to turn it back on. I have to physically disconnect power cable. The problem can occur anytime, when I'm booting Windows, when I'm logging in, when I'm listening to a song, when I'm browsing Internet, etc. It always occurs after very few minutes of 3D gameplay I thought it was a video card fault. I had 3 8800GTX so I could try all combinations of them: didn't fix I thought it was a RAM problem: I tried running with only a subset of my DDR2 banks but didn't fix. Almost every time I have to reset and reconfigure BIOS (without AHCI, Win7 won't boot, so I need to restore a few things). If I enable AMD Live, Cool&Quiet or other things from CPU configuration menu I'll be sure that the computer won't reach Windows desktop in 99% of cases (it randomly hangs somewhere in the boot process or even in the BIOS POST). Another interesting thing is that during the POST process the computer always takes unusually long time detecting USB devices (LCD POSTer shows USB INIT), and I've also tried disconnecting all USB devices but didn't take less time to POST BIOS revision is 2702, the latest. Today I found a different behaviour once: during boot screen I got a BSOD with error Stop 0x00000101 A clock interrupt was not received on a secondary processor within the allocated time interval, and this is usually related to overclocking, but I never overclocked my CPU. Judging from the description of my problem, hoping someone had the same and fixed, and since I don't have a spare CPU or motherboard for replacement, I'd like to ask if you think this is a problem with faulty CPU or faulty motherboard, and if I can perform additional tests (I mean software tests because of my lack of spare components) to identify the component to replace.

  Read the article

• Hibernate between OS X and Bootcamp Win 7

  - by Willem

  Wouldn't it be great if someone wrote a guide or an app which allowed you to switch instantly between OS X and Windows using Hibernate in both OS:s? Windows 7 already has an option "Hibernate" which allows you to boot back to your OS X partition, but OS X does not exactly offer the same. However, there are possibilities here. It seems that the recent Mac's have 3 different kinds of sleeping mode: Sleep: Low power consumption, RAM still active. Legacy Safe Sleep: No power consumption(?), writes RAM to disk and shuts down (is this the same as Hibernate?) Safe Sleep: Writes RAM to disk and enters sleep mode. If battery level drops too low it goes into Hibernate (is this Hibernate the same as #2 in this list? This is the Hibernate I will be referring to int he rest of this post) It seems that I am unable to force my MacBook Pro (Late 2011) OS X 10.7.3 into a true hibernate using either command line or apps that are supposed to do this. I believe the Mac should show that white loading bar whilst waking up if it was truly put into hibernate (which it does not). But I can get this white bar to show by letting my battery level drop to 0% so there is obviously a system function for it (obviously, duh! :). When Win 7 goes into hibernate it shuts down completely and you can then boot into OS X on startup. On OS X however, hibernate forces you to wake up into OS X. Can you hack this so that you're allowed to select boot partition after OS X hibernates? Would it be possible to use the true hibernate system functionalities of Win 7 and OS X to create a kind of instant switching between the two? Imagine this on a quick SATA-3 SSD like my 180GB Intel 520. Thanks / Willem

  Read the article

• Sparc Solaris 2.6 will not boot

  - by joshxdr

  I have a very old Sparc Solaris network that was working fine last week, but after a power outage none of the workstations will boot. The network looks like this: host A: solaris 2.6, shares /export/home to network by NFS host B: solaris 8, runs NIS server. Mounts /export/home/ by NFS. host C: RHEL5, shares /share to network by NFS. Mounts /export/home/ by NFS. I figured that the main problem was host A, since you need the home directories available for the other workstations to boot(?). Host A does not mount anything by NFS as far as I know. However, this workstation will NOT boot. The OBP bootup sequence looks like this: Boot device <blah> configuring network interface le0 Hostname <hostname> check file system <everything ok> check ufs filesystem <everything ok> NIS domainname is <name> starting router discovery starting rpc services: rpcbind keyserv ypbind done setting default interface for multicast: add net 224.0.0.0: gateway <hostname> <HANGS at this point> Is there some kind of debug mode so that I can get more detail as to why the workstation won't boot? Is my network structure inherently susceptible to power outage? Is there a way I can boot up to command line so I can at least turn off the NFS mounting?

  Read the article

• Looking to get a small server – need web, PHP, PostgreSQL.

  - by Javawag

  Hi all! I'm looking to get a cheap (low end) server to serve web pages (xHTML/PHP), but I also need to be able to set up PostGreSQL on the system too. Ideally the server would have low power consumption, run Linux (I prefer Mac OS X but a Mac Mini, although the size I'm looking for, is too much money!) and be around £100 (~$160US). EDIT: Just to make it clearer, I'm looking to purchase the server hardware myself – but I want something about Mac Mini sized. I don't want to pay for hosting! Also, quick question – if it's to serve web pages from my home (standard ISP connection, no static IP!), what do I need in place to get this working. I'm guessing I would sign up with some service like no-ip, and register a domain to point to my no-ip address (then install the no-ip software on the server to update that with the current IP). I know the idea of running a server behind a normal ISP connection isn't very elegant, but I'd prefer to have the server where I can see it then pay over the odds for a hosting service where I have little to no control over what happens. Also, I could write my own server software for apps/etc to connect to as well. Anyways I'm rambling! What do you guys think?! Javawag

  Read the article

• DRBD stacked resources: recovering from failure

  - by Marcus Downing

  We're running a stacked four-node DRBD setup like this: A --> B | | v v C D This means three DRBD resources running across these four servers. Servers A and B are Xen hosts running VMs, while servers C and D are for backups. A is in the same datacentre as C. From server A to server C, in the first datacentre, using protocol B From server B to server D, in the second datacentre, using protocol B From server A to server B, different datacentres, stacked resource using protocol A First question: booting a stacked resource We haven't got any vital data running on this setup yet - we're still making sure it works first. This means simulating power cuts, network outages etc and seeing what steps we need to recover. When we pull the power out of server A, both resources go down; it attempts to bring them back up at next boot. However, it only succeeds at bringing up the lower-level resource, A-C. The stacked resource A-B doesn't even try to connect, presumably because it can't find the device until it's a connected primary on the lower level. So if anything goes wrong we need to manually log in and bring that resource up, then start the virtual machine on top of it. Second question: setting the primary of a stacked resource Our lower-level resources are configured so that the right one is considered primary: resource test-AC { on A { ... } on C { ... } startup { become-primary-on A; } } But I don't see any way to do the same with a stacked resource, as the following isn't a valid config: resource test-AB { stacked-on-top-of test-AC { ... } stacked-on-top-of test-BD { ... } startup { become-primary-on test-AC; } } This too means that recovering from a failure requires manual intervention. Is there no way to set the automatic primary for a stacked resource?

  Read the article

• BIOS not detecting working SATA hard drive

  - by user28927

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• How to calibrate ASUS k52f battery on Ubuntu?

  - by cutalion

  I'm not sure if the problem is in software or my battery is dying, I'll move my question to another forum if it's not a SO question I have a problem with the battery on my laptop - ASUS K52F. It shows incorrect information about capacity. When I unplug the charger it can work some time, but then it will power off without any warnings. Sometimes it will power off right after I unplug the charger. Here is some info I could get: > uname -a Linux alligator 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux > acpi -i Battery 0: Charging, 99%, 18:25:15 until charged Battery 0: design capacity 5235 mAh, last full capacity 69964 mAh = 100% > cat /sys/class/power_supply/BAT0/uevent POWER_SUPPLY_NAME=BAT0 POWER_SUPPLY_STATUS=Charging POWER_SUPPLY_PRESENT=1 POWER_SUPPLY_TECHNOLOGY=Li-ion POWER_SUPPLY_CYCLE_COUNT=0 POWER_SUPPLY_VOLTAGE_MIN_DESIGN=10800000 POWER_SUPPLY_VOLTAGE_NOW=9246000 POWER_SUPPLY_POWER_NOW=176000 POWER_SUPPLY_ENERGY_FULL_DESIGN=**48400000** POWER_SUPPLY_ENERGY_FULL=**646822000** POWER_SUPPLY_ENERGY_NOW=**643588000** POWER_SUPPLY_MODEL_NAME=K52F-44 POWER_SUPPLY_MANUFACTURER=ASUSTek POWER_SUPPLY_SERIAL_NUMBER= I noticed, that POWER_SUPPLY_ENERGY_NOW and POWER_SUPPLY_ENERGY_FULL are greater than POWER_SUPPLY_ENERGY_FULL_DESIGN. I don't think it's ok :) I can run any additional commands.

  Read the article

• Copying files between linux machines with strong authentication but without encryption

  - by Zizzencs

  I'm looking for a suitable program to copy files from one linux machine to another one. The program should be able to do authentication but it should not do encryption. The reason behind the latter is the lack of CPU power to do the encryption. I copy backups from ~70 machines to a single backup server simultaneously. The single server is an HP Proliant DL360 G7, with 10 Gbps ethernet connection and an FC storage backend that can do 4 Gbps. Through FTP I can write ~400MB/sec to the storage (that's about what I want) but through ssh with arcfour I can only do ~100MB/sec while having 100% CPU usage. That's why I want file transfers not to be encrypted. The alternatives that I found not really suitable: rcp: no authentication, forget it FTP: making the authentication "secure" (at least preventing plain-text password exchange) is possible but not really easy and I haven't found a method to force any FTP daemon to encrypt the control channel (for the authentication) and not to encrypt the data channel (for data transfers) SCP/SFTP: in farely recent ssh(d) implementations you can't turn off encryption. The best you can do is to use the arcfour cypher for the encryption but it sill uses too much CPU power for my needs. rsync over ssh: same problems as with SCP/SFTP. plain rsync: from the documentation of rsyncd: "The authentication protocol used in rsync is a 128 bit MD4 based challenge response system. This is fairly weak protection, though (with at least one brute-force hash-finding algorithm publicly available), so if you want really top-quality security, then I recommend that you run rsync over ssh." It's a no-go. Is there a protocol/program that can do exactly what I want? (A big plus would be if it could work on windows as well and/or if it would support rsync-stlye copying/synchronization (e.g. copy only the differences).)

  Read the article

• Suggestions for Backup solution

  - by jiewmeng

  i am considering between windows home server simple nas extra HDD's in desktop btw, i will be the main user i am looking to fulfil the following needs: reliability (i am think RAID 1 or 5) not so prone to virus/malware infections (will using a separate NAS or home server help? say windows home server is still a windows pc except separated by network?) power efficiency (eg. spin down when not in use) download (eg. i may want to dl big files/torrents overnight and i may not want to use a full powered PC for it? does a full pc vs NAS provide significant power usage to justify cost of new system esp. since i am only user?) performance (i guess i like to write/access my files fast, on 2nd thought, maybe for backup i can forgo this? maybe for a WD Green HDD? but how much slower will it be? plus since i am the only user, i think the whole HDD will be mine?)

  Read the article

• Offline productivity

  - by Frank Meulenaar

  On some days I'm commuting 2hs (oneway) in the train. I don't have any mobile internet nor is there always WiFi service in the train. Because of security reasons I can't do any work in the train so I'm trying to work on my geek time. I'm looking for general solutions on how to do this (I'm on FireFox/Windows but I don't think it matters) Email works perfectly with gmail offline. It syncs directly when online and remembers complicated stuff. So far I used the ScrapBook plugin to store an website. It works good, but I have to download my favorite news page every day again - I want it to sync as soon as possible. It would even be more awesome if I could click a page on my desktop and my laptop would sync as soon as it has the chance. (edit: maybe the autosave plugin for scrapbook can do this) Similarily, I use the Downloadhelper plugin to download youtube vids, but I'd like something that automatically downloads videos from a given channel. Any tips are welcome. So far my early morning schedule is: wake up, power on laptop, make coffee, power off laptop and leave within 10 minutes (enough time for GMail to sync) but I can imagine a system where my laptop stays on during the night (or boots before I wake (and makes me coffee :])).

  Read the article

• System occasionally hangs boot process with SLES 11

  - by ThaMe90

  I have several (new) systems on which I had to install SLES11 on. However, after a few (though not every) reboots, the system hangs during the boot sequence. It will only continue after I physically press a key on the keyboard. From what I've found in the dmesg log from a failed boot is the following: [ 22.170276] sd 0:0:0:0: [sda] Mode Sense: b7 00 00 08 [ 22.171155] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 22.182760] sda: sda1 sda2 sda3 [ 22.383424] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.545372] PM: Marking nosave pages: 000000000009a000 - 0000000000100000 [ 22.545377] PM: Marking nosave pages: 00000000bf780000 - 0000000100000000 [ 22.546217] PM: Basic memory bitmaps created [ 22.590380] PM: Basic memory bitmaps freed [ 22.596284] PM: Starting manual resume from disk [ 22.602319] PM: Resume from partition 8:1 [ 22.602321] PM: Checking hibernation image. [ 22.602479] PM: Error -22 checking image file [ 22.602481] PM: Resume from disk failed. [ 22.718727] kjournald starting. Commit interval 15 seconds [ 22.718960] EXT3-fs (sda3): using internal journal [ 22.718964] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 1555.644404] udevd version 128 started [ 1555.697664] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1555.707961] ACPI: Power Button [PWRB] I've looked around the internet for the PM: Resume from disk failed. message, but this seems to only be important when restoring the system after a hybernate, i.e. restore from the hdd. But this is not my situation. I only get this after a reboot, as I said before. The timestamp [ 1555.xxxxxx] is only the result of me pressing a key on the keyboard. Any suggestions on how to proceed? As I am getting stuck on this issue.

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

• Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

  - by ZiGi

  i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

  Read the article

• KVM Guest Reboot Loop

  - by javano

  I have been pulled into a situation where a KVM server (CentOS 6.2) lost power and upon reboot one of the guests hasn't started up again (XP SP3). I have SSH'ed in and someone must have changed something relating to the hyper visors prior to the power loss, but not rebooted all the guests. This particular guest wouldn't start because it was configured to use /usr/bin/qemu-system-x86_64 which isn't there now (assuming it was before?). I changed it to use /usr/libexec/qemu-kvm as this is what all the other guests on this server seem to be using, and its booting up. Using virt-manager on my local machine I can connect to the display of the XP machine and it gets as far as this screen; http://support.gateway.com/emachines/issues/2-1131285152-01.gif The problem I face now, is that which ever option I choose the machine just reboots. So it's and endless loop. I thought that perhaps a file system error maybe present due to the unclean shutdown. There is an XP SP3 ISO mounted under the guest, which I booted from in an attempt to access the recovery tools, but I don't have the Administrator password! I am out of ideas, and it's turning out to be quite the conundrum. Should I use a 3rd party live CD to test the FS for errors? How else can I trouble shoot these restarts?

  Read the article

• How can I pair two bluetooth dongles together?

  - by techaddict

  I want to hack a device which connects via USB, and plug a bluetooth USB dongle to the end of the USB cable (using a female to female adapter), and then connect to that device from another USB bluetooth dongle connected to my computer. How can I do this? It is straightforward? I don't want to spend $30 before I know how to do this. Also I think another concern is that the USB cable is providing power to the device. So I think that means I would also have to hack it for power. I have created this diagram in Photoshop to illustrate my intent: (NOTE: it won't be a USB mouse, as that would be pointless because there are already wireless mice in existence. The mouse is displayed for illustrative purposes) Don't tell me "it won't work". Because I KNOW it WILL work. Think for example, PS3 controller. That works, and in fact I was able to get it working with my laptop, over bluetooth. I just want to know HOW to make it work.

  Read the article

• Cisco 851 (IOS) router: FastEthernet 4 (WAN) got the shutdown flag.

  - by cjavapro

  At a customer location there was a Cisco 851 router (which uses IOS). The PCs on location were all of a sudden unable to connect. We came on site and found that FastEthernet 4 (the WAN port) was "administratively down". We ran these commands to resolve it config t interface fa4 no shutdown exit exit write Now the mystery is how the shutdown flag got there in the first place? The router was on battery backup... but during the outage it was power cycled by the customer. It is possible that there was a short outage by the ISP and that the power cycle caused the shutdown flag to come up. There may have been a hack or an attack pattern that caused the shutdown flag to come up. There may have been a hack or an attack pattern that the router to become unavailable and then caused the shutdown flag to be added on startup. Question: Does anybody have any clues? or at least remember that they had a shutdown flag come up on their WAN port also?

  Read the article

• Computer crashes if left unattended AND running uTorrent, what could be?

  - by DiegoDD

  I have a weird problem in which, if I leave my computer unattended, AND I leave uTorrent open, downloading/seeding, the computer simply crashes after about 20 / 30 minutes (don't know exactly since if I leave it, and come back later, it has already restarted or has a BSOD.) If I leave the computer alone for undefined time WITHOUT uTorrent, nothing happens, and if I am constantly using the computer while using uTorrent, no problem either (I could be using it all day with uT open and it doesn't crash). So what could it be that the combination of those cases makes the computer crash? I have already checked the power management so the computer never enters stand by mode, sleep, hibernate, etc. (the only thing I do is turn off the display). A first guess is that maybe one of my external hard drives DO sleep or enters in a "low power" mode or something if I don't use the PC. but since uT is running MAYBE tries to use that drive, and makes it crash. Could that be possible? How to know for sure if the external drive does that, and to prevent it from doing so. Any more ideas of what may be causing that? Specs: Windows 7 Pro, 64-bit, 2 GB RAM. Latest version of uTorrent (although it has been happening for a while now). UPDATE: i just found out that uTorrent has Disk cache options ( preferences - advanced - disk cache ). I have no idea if that may be causing problems with my external drive, hence causing the crash.

  Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >