Search Results

Search found 5864 results on 235 pages for 'secure gateway'.

Page 131/235 | < Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >

  • How to rebuild a Li Ion laptop battery?

    - by spoulson
    I have an aging Gateway NX560XL laptop. The battery is toast and a new one, even aftermarket, starts at $130. So, to experiment, I began tearing apart the old battery to see what can be done. I found it used 8 standard size 18650 Li Ion cells arranged two cells parallel then in series (like: ====). Some online shopping revealed ~$7-13/ea replacements depending on mAh output. My plan is to load test to determine the bad cells and replace only those, as I read that typically only 1 or 2 may be bad. I'm proficient with soldering, however these cells are attached with welded tabs. Some of them broke during disassembly and I'm not sure how to reattach them. What I found online are cells like these that have solder tabs pre-welded to the ends so I can solder wires onto. Is there any guide available that provides the instructions and parts to do this kind of rebuild?

    Read the article

  • Lot of Multicast traffic on LAN

    - by Nel
    Recently the whole network at work is being hit by multicast traffic originating on the LAN itself. I did some investigating and the service which seems to be responsible is ws-discovery. I have attached a screenshot of wireshark capturing the traffic. I have tried shutting down the source machine from which it was originating, but the multicast traffic still seems to be present in the network. My network topology 2 subnets - 10.10.10.0/24 and 10.20.10.0/24. Gateway is a debian system. We have 3 switches for 3 floors. They are all unmanaged Dlink 24-port switches. Multicast blocking at switch level is out of the question. Any solutions? :(

    Read the article

  • Where should I go with hosting my site: VPS, GAE, another option?

    - by Jonathan Hayward
    My website, http://JonathansCorner.com/, began life before 1994 as www.imsa.edu/~jhayward/ and has been through various iterations and improvements to content, HTML, and the like, but remains a literature site that is from a web administrator's perspective fairly simple and primitive: a fair amount of static HTML and supporting files, a little bit of CGI and URI rewriting, .htaccess files providing Expires: headers and the like. An associated site demoes various CGI scripts that fall under the category of "and other creations"; the site as a whole has the purpose of sharing my creative works, and so far a fairly rudimentary use of Apache functionality, supported by Unix tools to, for instance, update RSS feed and the "starting point" link on the home page, has served that purpose fairly well. I looked around here on web hosting, and found the note on web host reccommendations as a good note for "What are some of people's favorite web hosts overall," but I wanted to ask a more focused question of "What are the best web hosts for criteria XYZ:" I am looking at a VPS so I will have root, be able to install stuff and edit Apache's config files etc., running Gentoo or other Linux, BSD, or the like. I would like a system that is secure enough that the host's vulnerabilities are mostly the ones that come along with what I am trying to do: that is, I won't be trying to administer and secure an ancient Linux like some have complained about at 1and1. I would like good uptime/reliability and competent support staff: if the level 1 help desk is going to tell me to go to "My Computer" on a Linux box, I'd like to be able to get past them. Ideally I would like a site hosted within some place that will have low latency for U.S. visitors in particular. I would like a hosting solution that will be with a stable business, one that will probably be around, and one unlikely to vanish without warning. With those things specified, I would be interested in knowing what are the less expensive options. (I expect that some of the things I've specified will knock out all of the cheapest options, but I'm still interested in price.) With all that stated, I'd like to back up a bit and look at whether I am asking the right question. I am concerned that the above is a very good way of asking, "How can I keep my site in line with the wave of the past?" I am wondering if it might be specifically wiser to look to adapt my site to newer technologies instead of trying to keep it on older technologies. For instance, while I would hardly portray my site as a way to show off the full power of Google App Engine, the main site at least should be a straightforward port if I were to do that. And beyond Google App Engine, my knowledge of cloud solutions is basic. If it is a better and more future-proof solution to port my site to another kind of solution, I would be interested in knowing where those future-proof solutions lie. So I would be interested in wisdom. If the question I asked in detail is still a good question to be asking, what would people suggest? Or if I should seriously consider porting my site to a newer basic option, what should I try there? Any thoughts would be appreciated.

    Read the article

  • How do I delete a route in OS X 10.5

    - by authormichael-olsen-craig
    I somehow configured my Mac to route all requests for a particular IP Name (sample.com) to the loopback address (127.0.0.1). Now I'm trying to remove this, but can't determine where to do it. There is no entry for it under /etc/hosts. The routing table shows that it is mapping the IP Name to the IP address of the Mac. Routing table output below: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.2.1 UGSc 4 1 en0 127 sample.com UCS 0 0 lo0 sample.com sample.com UH 1 7093 lo0 169.254 link#4 UCS 0 0 en0 192.168.2 link#4 UCS 6 0 en0 192.168.2.1 0:11:22:22:3f:fa UHLW 20 55565 en0 1070 192.168.2.15 tsema.org UHS 0 9 lo0 192.168.2.255 link#4 UHLWb 4 84777 en0 Any help would be greatly appreciated!

    Read the article

  • Can TP-Link router make phone calls?

    - by Umair Ashraf
    I have a TP-Link router with DSL service provided by a local company which serves it over the landline phone. My landline cord is plugged into an ethernet router which is then plugged into TP-Link wireless router. I can access internet with this wireless router all over my home with all computers. Landline Cord [into] Ethernet Router [into] TP-Link Wireless Router [air] Computers I would add that landline cord is also into a phone device which I use to make calls and that's not cordless. Now I am accessing internet via WiFi on my laptop and want to ask if is this possible to make landline calls via this same computer I am surfing internet through? What I am asking it to a dial-up via TP-Link router that goes through landline. You see the landline cord is the actual data gateway and is also used to make calls. So it can simultaneously send Data and Voice over the same wire.

    Read the article

  • Shrew VPN Client gives default route- changing the policy stops me from accessing VPN network

    - by Lock
    I am using the shrew client to connect to what I believe is a Netscreen VPN. Now, when connected, the client adds the VPN as the default route. I do not want this- there is only 1 network behind the VPN that I need to access. I found that with the shrew client, you can change the "Policy" settings on the connection, and can add your own networks in that should tunnel over the VPN. I do this, and add my network in, but when I connect the VPN, I get nothing. Can't access the network. Any idea why this would be? I can see my network in the routing table, and its correctly pointing to the correct gateway. A traceroute shows all time-outs, so I can't be 100% sure that it is trying to tunnel over the VPN. Any idea how I can troubleshoot this?

    Read the article

  • Specific IP routing for VPN

    - by Roy
    Is there a way that I can prevent an entire subnet from using internal routing. The VPN server is supposed to be a way to access the company's intranet websites for some people, while for others it is supposed to do routing to the outside only and therefore not having access to any internal websites. The VPN server has a DNS on the actual server but not all should be using this DNS. Some of the users should be directly sent out of the server to the internet. Example: 10.0.0.1 is the DNS on the server, gateway for the VPN 10.0.0.2 is a user (A) on the VPN having access to the intranet websites (subnet is 10.0.0.0/25) 10.0.0.192 is a user (B) only needing routing and no access to intranet websites (subnet is 10.0.0.192/26) All traffic of user B should be directly rerouted out of the server. I have tried several iptables but without success.

    Read the article

  • KVM Guest not reachable from host

    - by Paul
    Hello, I'm running Ubuntu server 9.10, installed KVM etc. Created the bridge network following instructions on help.ubuntu.com/community/KVM/Networking Created a windows 2008 guest using virt-install command line (using virt-manager GUI from a remote Ubuntu desktop would not let me select the ISO location). I can however use a remote virt-manager to connect to the guest and complete the windows install. Within windows 2008 I changed the IP address but cannot ping from outside world. The bridge network appears fine - I'm not sure what else to look at! Here is the interfaces file: The loopback network interface auto lo iface lo inet loopback The primary network interface auto eth0 iface eth0 inet manual # auto br0 iface br0 inet static address 60.234.64.50 netmask 255.255.255.248 network 60.234.0.0 broadcast 60.234.0.255 gateway 60.234.64.49 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 auto eth1 iface eth1 inet static address 192.168.12.2 netmask 255.255.255.0 broadcast 192.168.12.255 The ip of the windows server is 60.234.64.52 What else should I check? Regards Paul.

    Read the article

  • XenServer VM's lose network settings

    - by Ash
    We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

    Read the article

  • Debian 6 Internet connection sharing aka IP masquerade not working

    - by Rautamiekka
    The problem: the computers [Xbox 360 and a Kubuntu 12.04.1 laptop] can't access Internet through a recently-installed desktopless Debian 6 laptop (which is wirelessly connected to a WLAN station) but addresses are successfully given by dnsmasq. The attempts: 1.1) /etc/dnsmaq.conf conffed according to http://wiki.debian.org/HowTo/dnsmasq: add lines interface=eth0 dhcp-range=192.168.0.50,192.168.0.150,255.255.255.0,12h 1.2) Follow http://www.cyberciti.biz/faq/rhel-fedora-linux-internet-connection-sharing-howto/ and use their script to setup iptables. 2) Follow the Ubuntu Internet Gateway Method (iptables) at https://help.ubuntu.com/community/Internet/ConnectionSharing recommended and which worked at Share internet in Linux. The Debian laptop was rebooted many times and between each attempt, with and without the script auto-executing via /etc/rc.local. While adding the iptables-restore command to that file I disabled the script.

    Read the article

  • dhclient configures /etc/resolv.conf with invalid entry

    - by kubal5003
    I'm trying to figure out why running dhclient on my interface sets /etc/resolv conf to the ip number of my gateway(router). This entry is invalid and each and every time causes inability to resolve any address. I would like to: stop dhclient from overwriting the /etc/resolv.conf or make dhclient write there the valid dns ip from my router More on the environment: I'm using virtual Debian Wheezy as a client system on Windows Seven x64. It is run by Virtualbox with networking mode set to bridged (all packets from debian are injected to my network interface on windows). If I manually configure the /etc/resolv.conf then everything works fine. Doing this on every boot is quite annoying.. PS I know I can write a script to do it for me, but this is not the solution I want. //edit router ip: 192.168.1.100 /etc/resolv.conf AFTER running dhclient eth0: "nameserver 192.168.1.100" what I would like the /etc/resolv.conf to look like: "nameserver 89.202.xxxx" (I don't have to provide the real ip do I? )

    Read the article

  • Implementing a form of port knocking + Phone Factor = 2 Factor auth for RDP?

    - by jshin47
    I have been looking into how to secure a publicly-available RDP endpoint and want to implement our two-factor authentication RADIUS server, PhoneFactor. I would like to implement the following process: User opens up web app in browser In web app, user enters username + password, initiates RADIUS auth Phone factor calls user to complete auth Once user is authenticated, port 3389 is opened on user's IP on pfSense firewall. After some amount of time, firewall rule is removed for that IP I would like to know the following: Is this a typical setup? If it is a bad idea, please explain why. If it is possible, are there any packages that assist with this? Specifically, the third step, where the appropriate firewall rule would need to be added... Edit: I am aware of TS Web Gateway, but I want the users to be able to use the traditional RDP client...

    Read the article

  • Recover from running "route -f"

    - by James L.
    I was trying to capture localhost traffic with Ethereal, which doesn't work without re-routing localhost traffic to your router gateway. I didn't get the route command quite right, and messed up my routing table. I typed route -f to clear the routing table and rebooted, but when I finished rebooting, the routing table wasn't restored to its original state. I didn't use the -p parameter, so none of my changes should have persisted after a reboot. What can I do to restore the routing table to its default routes?

    Read the article

  • Automatically generated /etc/hosts is wrong

    - by Niels Basjes
    I've created a kickstart script to install CentOS 5.5 (32bit) in a fully automated way. The DNS/DHCP setup correctly gives the system the right hostname in both the forward and reverse lookups. dig node4.mydomain.com. +short 10.10.10.64 dig -x 10.10.10.64 +short node4.mydomain.com. In the state the installed system is right after the installation completed is as follows: cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=yes GATEWAY=10.10.10.1 HOSTNAME=node4.mydomain.com echo ${HOSTNAME} node4.mydomain.com cat /etc/hosts # Do not remove the following line, or various programs # that require network functionality will fail. 127.0.0.1 localhost.localdomain localhost ::1 localhost6.localdomain6 localhost6 10.10.10.64 node4 My problem is that this automatically generated hosts file is slightly different from the way I want it (or better: the way Hadoop wants it). The last line should look like this: 10.10.10.64 node4.mydomain.com node4 What do I modify where to fix this? Thanks.

    Read the article

  • Why is my eth0 getting a dynamic ip when it is configured to be static?

    - by sdek
    For some reason our office linux box is being assigned an ip address via dhcp and I don't know why. What is confusing to me is that when I check system-config-network it shows that my eth0 is setup to be a static ip address. And /etc/sysconfig/network-scripts/ifcfg-eth0 also shows it is setup to be a static ip, yet it is getting a different ip address than the one specified in the ifcfg-eth0. Let me know if you have any suggestions on or ideas on where I can look next. Here are a few details that might help you figure out what an idiot I am :) Fedora 11 Router in front of this box is running dhcp, starting at 10.42.1.100 This box is configured to be 10.42.1.50 (at least I think it is!), subnet 255.255.255.0 (which is same as the router's lan subnet) Instead of having the static IP, this box is getting assigned 10.42.1.100. Here are the ifcfg-eth0 details DEVICE=eth0 BOOTPROTO=none ONBOOT=yes TYPE=Ethernet USERCTL=no NM_CONTROLLED=no NETMASK=255.255.255.0 IPADDR=10.42.1.50 GATEWAY=10.42.1.1

    Read the article

  • SQL Server 2008 R2 100% availability

    - by Mark Henderson
    Is there any way to provide 100% uptime on SQL Server 2008 R2? From my experience, the downtimes for the different replication methods are: Log Shipping: Lots (for DR only) Mirroring w. NLB: ~ 45 seconds Clustering: ~ 5-15 seconds And all of these solutions involve all of the connections being dropped from the source, so if the downtime is too long or the app's gateway doesn't support reconnection in the middle of task, then you're out of luck. The only way I can think to get around this is to abstract the clustering a level (by virtualising and then enabling VMWare FT. Yuck. Good luck getting this to work on a quad-socket, 32-core system anyway.). Is there any other way of providing 100% uptime of SQL Server?

    Read the article

  • CentOS: eth0 not starting on boot

    - by Cameron Aziz
    Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3. After I perform ifup eth0 on the console: [root@localhost ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:15:5D:2B:2B:07 inet addr:10.10.0.3 Bcast:10.10.0.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:49 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4656 (4.5 KiB) TX bytes:6399 (6.2 KiB) Interrupt:9 Base address:0xa000 [root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none IPADDR=10.10.0.3 NETMASK=255.255.255.0 GATEWAY=10.10.0.1 USERCTL=no ONBOOT=yes [root@localhost ~]# chkconfig --list | grep network network 0:off 1:off 2:on 3:on 4:on 5:on 6:off

    Read the article

  • Cascading switches: uplink to uplink?

    - by wuckachucka
    I'm a bit confused as to why I haven't seen any references online to using Switch A's uplink port (1Gbps, 24-port 10/100) to connect to Switch B's uplink port: everything I've seen -- including documentation, forums, articles, etc. -- has Switch A's uplink port going to one of Switch B's 10/100 access ports. As I understand it, the Uplink port (besides greater speed normally) is no different than another port except that it's "internally crossed-over" so that you can use a straight cable with it. I've also seen documentation on using the uplink port to connect a switch to a gateway router, or even a server, as it provides greater bandwidth than the access ports, but yet not sure why nobody seems to be cross-uplinking, even when there's 2 uplink ports available on some higher-end switches. Switch in question is Linksys SRW224P (x2). Am I missing something?

    Read the article

  • Is there any viable alternative to using a linux/unix/BSD firewall/router/vpn?

    - by ObligatoryMoniker
    I am trying to purchase something to replace our Vyatta router that is running in a virtual machine on Hyper V (having the whole network go down when the host has to reboot is not convenient and I am getting the sense that this configuration may not be stable). Most posts on this topic suggest using Linux/OpenBSD/FreeBSD/etc with some recommendations to use appliances from vendors for specific purposes like firewall and VPN. We are a windows shop and it has been a stretch for us to make use of Vyatta but since it was free and straightforward to use we decided to use it. Now we need something that is easier for our team to (re)deploy and manage. I would rather purchase something windows based or an appliance that can do all of the following things: DHCP server (reservations, specified gateway, dns, etc) Static Routes that route traffic across three interfaces Easily Reproducible (Powershell script, Puppet, Chef, etc) Intuitive interface (Decent web interface would be fine but I don't want them to have to go to CLI) Does any one have any recommendations on what I should be looking at that might meet our needs?

    Read the article

  • Belking Wireless Router unable to connect to internet although wireless connection is working

    - by ptamzz
    I have a Belkin Basic N150 Wireless router. I'm trying to set up wireless connection using the wired ports my university has provided in my hostel room. Usually, when I connect my laptop using a LAN wire through the port, my settings are like IP: 10.5.130.X Subnet Mask: 255.255.254.0 Default Gateway: 10.5.130.250 DNS Server: 10.200.1.11 and I'm able to connect to the internet. Now instead of connecting my laptop directly, I've connected the lan wire to the Belkin Wireless Router, set the router as "Use as an Access Point" and in the IP field, I've put up 10.5.130.1. Now I've set the IP of my system manually to 10.5.130.3. I'm able to connect to the wi-fi but I'm still not able to connect to the internet. What am I missing?

    Read the article

  • Setup routing and iptables for new VPN connection to redirect **only** ports 80 and 443

    - by Steve
    I have a new VPN connection (using openvpn) to allow me to route around some ISP restrictions. Whilst it is working fine, it is taking all the traffic over the vpn. This is causing me issues for downloading (my internet connection is a lot faster than the vpn allows), and for remote access. I run an ssh server, and have a daemon running that allows me to schdule downloads via my phone. I have my existing ethernet connection on eth0, and the new VPN connection on tun0. I believe I need to setup the default route to use my existing eth0 connection on the 192.168.0.0/24 network, and set the default gateway to 192.168.0.1 (my knowledge is shaky as I haven't done this for a number of years). If that is correct, then I'm not exactly sure how to do it!. My current routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface MSS Window irtt 0.0.0.0 10.51.0.169 0.0.0.0 UG 0 0 0 tun0 0 0 0 10.51.0.1 10.51.0.169 255.255.255.255 UGH 0 0 0 tun0 0 0 0 10.51.0.169 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 0 0 0 85.25.147.49 192.168.0.1 255.255.255.255 UGH 0 0 0 eth0 0 0 0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0 0 0 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 0 0 0 After fixing the routing, I believe I need to use iptables to configure prerouting or masquerading to force everything for destination port 80 or 443 over tun0. Again, I'm not exactly sure how to do this! Everything I've found on the internet is trying to do something far more complicated, and trying to sort the wood from the trees is proving difficult. Any help would be much appreciated. UPDATE So far, from the various sources, I've cobbled together the following: #!/bin/sh DEV1=eth0 IP1=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 192.` GW1=192.168.0.1 TABLE1=internet TABLE2=vpn DEV2=tun0 IP2=`ifconfig|perl -nE'/dr:(\S+)/&&say$1'|grep 10.` GW2=`route -n | grep 'UG[ \t]' | awk '{print $2}'` ip route flush table $TABLE1 ip route flush table $TABLE2 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table $TABLE1 $ROUTE ip route add table $TABLE2 $ROUTE done ip route add table $TABLE1 $GW1 dev $DEV1 src $IP1 ip route add table $TABLE2 $GW2 dev $DEV2 src $IP2 ip route add table $TABLE1 default via $GW1 ip route add table $TABLE2 default via $GW2 echo "1" > /proc/sys/net/ipv4/ip_forward echo "1" > /proc/sys/net/ipv4/ip_dynaddr ip rule add from $IP1 lookup $TABLE1 ip rule add from $IP2 lookup $TABLE2 ip rule add fwmark 1 lookup $TABLE1 ip rule add fwmark 2 lookup $TABLE2 iptables -t nat -A POSTROUTING -o $DEV1 -j SNAT --to-source $IP1 iptables -t nat -A POSTROUTING -o $DEV2 -j SNAT --to-source $IP2 iptables -t nat -A PREROUTING -m state --state ESTABLISHED,RELATED -j CONNMARK --restore-mark iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j CONNMARK --restore-mark iptables -t nat -A PREROUTING -i $DEV1 -m state --state NEW -j CONNMARK --set-mark 1 iptables -t nat -A PREROUTING -i $DEV2 -m state --state NEW -j CONNMARK --set-mark 2 iptables -t nat -A PREROUTING -m connmark --mark 1 -j MARK --set-mark 1 iptables -t nat -A PREROUTING -m connmark --mark 2 -j MARK --set-mark 2 iptables -t nat -A PREROUTING -m state --state NEW -m connmark ! --mark 0 -j CONNMARK --save-mark iptables -t mangle -A PREROUTING -i $DEV2 -m state --state NEW -p tcp --dport 80 -j CONNMARK --set-mark 2 iptables -t mangle -A PREROUTING -i $DEV2 -m state --state NEW -p tcp --dport 443 -j CONNMARK --set-mark 2 route del default route add default gw 192.168.0.1 eth0 Now this seems to be working. Except it isn't! Connections to the blocked websites are going through, connections not on ports 80 and 443 are using the non-VPN connection. However port 80 and 443 connections that aren't to the blocked websites are using the non-VPN connection too! As the general goal has been reached, I'm relatively happy, but it would be nice to know why it isn't working exactly right. Any ideas? For reference, I now have 3 routing tables, main, internet, and vpn. The listing of them is as follows... Main: default via 192.168.0.1 dev eth0 10.38.0.1 via 10.38.0.205 dev tun0 10.38.0.205 dev tun0 proto kernel scope link src 10.38.0.206 85.removed via 192.168.0.1 dev eth0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.73 metric 1 Internet: default via 192.168.0.1 dev eth0 10.38.0.1 via 10.38.0.205 dev tun0 10.38.0.205 dev tun0 proto kernel scope link src 10.38.0.206 85.removed via 192.168.0.1 dev eth0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.73 metric 1 192.168.0.1 dev eth0 scope link src 192.168.0.73 VPN: default via 10.38.0.205 dev tun0 10.38.0.1 via 10.38.0.205 dev tun0 10.38.0.205 dev tun0 proto kernel scope link src 10.38.0.206 85.removed via 192.168.0.1 dev eth0 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.0.0/24 dev eth0 proto kernel scope link src 192.168.0.73 metric 1

    Read the article

  • Packet loss with all adapters on one PC only on the LAN

    - by Enigmativity
    I have a Windows 7 64-bit machine that is losing up to 20% of IP packets on both adapters - wireless & LAN. Browser traffic appears to be affected the most, but it is happening to all protocols. All other computers on the network are functioning fine. If I ping from my faulty machine to any machine on the LAN (wired or wirelessly), including the router/gateway and internet sites, I get up to 20% packet loss. If I do the following commands: ipconfig /release ipconfig /renew then I sometimes get my network performance back for a matter of a few seconds to less than a couple of minutes. Rebooting also works for a short period of time. This problem has been occurring for a couple of months and is getting worse. The computer used to work just fine. I updated the wireless adapter firmware the other day with no effect. Does anyone know what is happening?

    Read the article

  • Why did my laptop turn off?

    - by darenw
    Normally I can slip my running laptop into a backpack, go somewhere, and if it's no more than about half an hour later, it'll still be running. At the destination I plug in the AC power unit and all is well. I run it off of the AC unit before and after the trip, have the screen at less than full backlight brightness, and don't have any peripherals that burn power. Sometimes the wireless switch accidentally slides in the backpack, and that causes extra power to be used and the laptop dies before I reach the destination. Sad, but so be it. But sometimes the wireless switch is off, I've reached the destination in less than 30 minutes (typically 10-20 min), and I know the battery was fully charged, yet the machine is off. Is there a way to determine, after the fact, why the machine shut itself off? I'm running Linux on a fairly powerful Gateway with 4GB RAM, fancy nvidia graphics, dual core cpu, chosen more for number crunching power than battery life, but should last easily for half an hour if not an hour.

    Read the article

  • How can I access the external microphone with Ubuntu?

    - by Charles Merriam
    Sound in Ubuntu, it has its own special joy. I would like my external microphone to work. Symptoms: I can play sound through the speakers I can play sound through the headsets. Plugging and and plugging headphone output correctly switches. I can record from the built-in microphone, using "Sound Recorder" and others. but: I cannot record from the external microphone. My Sound Preferences/Input panel has no option for an external microphone. If the answer is upgrade the ALSA drivers, please say exactly what to type. Thank you. ======== I'm using Ubuntu 9.10 Karmic Koala on a laptop (Gateway W3501), Sigmatel. That is: ~$ head -1 /proc/asound/card0/code* ==> /proc/asound/card0/codec#0 <== Codec: SigmaTel STAC9205 ==> /proc/asound/card0/codec#1 <== Codec: Conexant ID 2c06 ~$ lspci | grep -i audio 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)

    Read the article

  • How can I log all traffic with its exact length?

    - by Legate
    I want to process all packets with their size going through our gateway server (running Debian 4.0). My idea is to use tcpdump, but I have two questions. The command I'm currently thinking of is tcpdump -i iface -n -t -q. Is it guaranteed that tcpdump will process all packets? What happens if the CPU is working to full capacity? The format of the output lines is IP ddd.ddd.ddd.ddd.port > ddd.ddd.ddd.ddd.port: tcp 1260. What exactly is 1260? I have the suspicion that it is the payload in bytes of the packet, which would be exactly what I need, but I'm not sure. It might be the TCP Window Size. Or perhaps there is an even better way of doing this? I thought about a LOG rule in iptables, but tcpdump seems easier and I don't know whether iptables can log the packet lengths.

    Read the article

< Previous Page | 127 128 129 130 131 132 133 134 135 136 137 138  | Next Page >