Search Results

Search found 49453 results on 1979 pages for 'memory mapped files'.

Page 132/1979 | < Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >

• Coffee spilled and went inside CPU...computer not starting

  - by Harpreet

  Today coffee got spilled over my table, and some of it (very less) reached the CPU placed under the table. I think little bit of it got inside the CPU through the front face of the CPU. As that happened the fan started running very fast and made noise. I tried to restart to see if it becomes fine, but the computer didn't start again. First it gave an error of "Alert! Air temperature sensor not detected" and didn't start. Next I tried again multiple times of starting the computer but then it gave some memory error. I was not able to start the computer. Incase there's a problem in hard disk or something related to memory, is there any way we can extract our work or data? I am scared if I am not able to extract my work in case some problem occurs like that. What options would I have? Help! EDIT: I have attached the photo here and you can see the area spilt in red circle. The hard drive electronics have been affected and internal speaker may also have been affected. Any advise on cleaning and if hard drive can work? EDIT 2: Are there any professional services offered to extract data from blemished hard disk, like this one, in case I am not able to run it personally?

  Read the article

• What parts of a motherboard age, and how can I choose one with the longest possible life?

  - by Robert Harvey

  I have a home-built computer that's probably about four years old. I realize this probably seems ancient to some folks, but computers have no moving parts (except the fans), so theoretically they should last a long time, if I still have software to run on them. A few weeks ago, it began blue-screening and freezing up, with various error messages. It almost always happened about five minutes after startup. I assumed that the video card was overheating, since the cheap little fan on the heatsink died, so I replaced it. Long story short, after upgrading the video drivers a couple of times and performing some other troubleshooting, I remembered that the last time this happened, I took out the memory SIMS and cleaned the contacts with a gum eraser, so I did that again (noting that the SATA cables were very close to the chips on the SIMS). I re-routed the cables and reinstalled the SIMS. So far, so good; the machine has been trouble-free since. But blue-screens are distressing; I never know what bits are being chewed up in my OS installation when something like this happens. So I'm wondering if I'm choosing my components properly. If it matters, it's an Intel D915GAG motherboard and Corsair memory, but what I'm wondering is, should I be looking for certain characteristics when I choose these parts for my next computer, so that I can avoid this problem in my next build?

  Read the article

• Windows, why 8 GB of RAM feel like a few MB?

  - by Desmond Hume

  I'm on Windows 7 x64 with 4-core Intel i7 and 8 GB of RAM, but lately it feels like my computer's "RAM" is located solely on the hard drive. Here is what the task manager shows: The total amount of memory used by the processes in the list is just about 1 GB. And what is happening on my computer for a few days now is that one program (Cataloger.exe) is continually processing large quantities of (rather big) files, repeatedly opening and reading them for the purposes of cataloging. But it doesn't grow too much in memory and stays about that size, about 90 MB. However, the amount of data it processes in, say, 30 minutes can be measured in gigabytes. So my guess was that Windows file caching has something to do with it. And after some research on the topic, I came across this program, called RamMap, that displays detailed info on a computer's RAM. Here is the screenshot: So to me it looks like Windows keeps in RAM huge amounts of data that is no longer needed, redirecting any RAM allocation requests to the pagefile on the hard drive. Even when I close Cataloger.exe, the RamMap reports the size of the mapped file as about the same for a long time on. And it's not just this particular program. Earlier I noticed that similar slowdown occurred after some massive file operations with other programs. So it's really not an exception. Whatever it is, it slows down the computer by like 50 times. Opening a new tab in Chrome takes 20-30 seconds, opening a new program can take up to a minute. Due to the slowdown, some programs even crash. So what do you think, is the problem hiding in file caching or somewhere else? How do I solve it?

  Read the article

• FastGate A20 Line And Himem.sys Issue With Updating BIOS

  - by Boris_yo

  I have been persistent with a thought to perform my first BIOS update ever through MS-DOS but have been postponing this task until today. Despite people telling me any bootable ISO will do it either through CD-ROM or RAMDRIVE, I am still having problems. First is the problem with CD-ROM driver trying to make it work with 4 driver files (cd1.SYS, cd2.SYS, cd3.SYS, cd4.SYS) as well as starting RAMDISK proved to be failure: CD-ROM XMS Allocation Error RAMDISK XMS Allocaton Error (X: and R: drives not working) This A20 line seemed to be the obstacle which then after a couple of searches pointed me to this article on Microsoft website. It seems that FastGate is the culprit which takes over A20 line and conflicts with himem.sys which should be handling it causing the driver to be unable to allocate memory resources. Albeit article suggests 2 workarounds which is disabling FastGate option or adding switch, I read that the former workaround could cause problems which involves later tinkering BIOS, disabling shadow copy etc. while the latter workaround can just hang system as stated in the link above. I assume it just hangs the boot process from image file though. Summing up the above, I am cautious and think it is risky to follow both workarounds because disabling FastGate or trying adding switch by trying available switches from 1-14 or 16, could crash the BIOS update process by itself. I could do this without the need for himem.sys with bootable USB thumbdrive by making it to be seen as USB-HDD, but some time ago I read that it is never a good idea to update BIOS from hard drive so even thought it is simulation, who knows... Maybe it will deactivate hard drive in the middle of the BIOS update process or even USB thumbdrive per se? One forum discussion was about updating BIOS and somebody suggested to not load himem.sys for some reason, but now that I think of it, what if BIOS update needs upper memory?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• 100% CPU load on Ubuntu 10.04.3 LTS 64bit

  - by deadtired

  I have 2 days since I am trying to fix this issue, with no success. The server is a mysql database server. Hardware: DELL Poweredge 1950, 2x Intel Xeon Quad Core E5345 @ 2.33GHz, 16 Gb mem, 2x 146Gb SAS (software RAID1) Software: Ubuntu 10.04.3 LTS, MySQL 5.1.41 Issue: while mysql is not used and runs with no database, everything seems alright. As soon as I install a database, it has the reason to bring all 8 cores in 100% with low memory consumption. So, you can imagine the load average goes high (I saw 212 load average for the first time). The server doesn't become unresponsive, but you can see it's slow while browsing the project installed. Additional info: the database used is not more than 24MB and it was moved from a server with less resources and a lot more larger databases. So it's not the database/project. my.cnf is not a reason also, as I used both default one and the one I use on the same distribution on another server.What is interesting is that mysql doesn't close any process and runs to the limit of the max_connections. Logs are quiet. Nothing there. I switched to this Ubuntu version after I suspected some problems in the newly Ubuntu 11.10 server. This one worked alright for an hour after I made a kernel upgrade to 3.0.1 (it was using the memory also) I tested disk speed and seems alright. Some more output on the running server: dstat -cndymlp -N total -D total 3: htop command: Idea? Did anyone meet the same problem? Any fix you can think of?

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• Win/Bios showing wrong RAM in Gateway Netbook?

  - by Ael

  I've seen similar problems, but this seems slightly unique, maybe... I have a Gateway LT21 netbook, Win7. I've upgraded RAM from 1gb to 2gb. It didn't work. So I updated to the latest Bios 1.25, then it worked. 2gb was recognized in the Bios and in Windows. Every was fine. Now today it seemed slow and, to my surprise, both the Bios and Win show only 1gb. :/ I've run memory diagnostic, no error. I entered bios and hit Exit and Save. Still 1gb. I took out the ram, put it back. Still 1gb. :/ CPU-Z shows 2048mb/2gb of RAM. Further testing: if i put in the old 1gb ram, turn on, then put in the new 2gb ram again, the Bios and Win show 2gb of ram. BUT, once restarted at all (even from Bios) it seems to go back to showing incorrect 1gb ram again. :// (There are very few options in the bios, none appear memory-related.) Any ideas?

  Read the article

• How can I setup BluePill to Monitor a Rails App Running via Passenger (mod_rails)

  - by Jim Jeffers

  I recently launched a site running phusion passenger. Unfortunately, the site went down due to a frozen thread. I was able to save the server by doing kill -9 to the specific PID. Still though, I thought passenger was able to manage this automatically. I have a server with 1GB of memory running one rails app with passenger allotted up to 7 instances. However, when I came to discover the site went down I found that passenger had spawned 6 instances with one of them using up over 800mb of memory causing the server to swap. As a result I am hoping to setup something like bluepill on the server but I'm slightly confused as to how you go about doing it. Mainly because bluepill expects to start/stop the processes it's monitoring. However, in our case, passenger already restarts processes for us so we only need to monitor the pids of passengers instances and kill them once they've gotten too large. Has anyone here setup BluePill to monitor a rails app running under phusion's passenger? Any insight would be useful.

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

• Ram configuration 4x4 or 2x8?

  - by Carl B

  I am looking to upgrade my Ram to 16gigs and I am wondering if there is any distinct advantage of the way I do it. That being a 4x4 or 2x8 set up. In all my searching there have been a number of pros for each profile. I can find no benchmarck results for either setup as a compaison. So, if there are 2 profiles of the same speed, same voltage, same timing and same cas what would perform better or have a better over all benafit? A few examples from my search - a 4x4 set would lend a benafit in that if one stick failed, you only lose 25% of your Ram vs 50% in a 2x8 set up. a 2x8 set up would have less strain on the memory controler and motherboard. a 2x8 would generate less heat. a 2x8 set up is easier to over clock (not part of my need, but alot of the comparisons circled around the overclocability ease of the 2 stick set up). There is one outstanding benafit that I have found in at least the target company I have looked at and that is price. The 2x8 is nearly half the cost. My motherboard supports a max of 16 gigs and I have a 64 bit OS. Has anyone seen any performance comparisons or is 16 gb just 16 gb no matter how you slice it? And is there any merit to the above pros? Edit: as per the mobo specs - Main Memory • Supports four unbuffered DIMM of 1.5 Volt DDR3 800/1066/1333/1600*/1800*/2133* (OC) DRAM, 16GB Max

  Read the article

• Low-traffic WordPress website on Apache keeps crashing server

  - by OC2PS

  I have recently moved my low-moderate traffic (1000 UAUs, 5000 pageviews on a busy day) website from shared hosting to a Centos 6 64-bit VPS with Apache and cPanel running on 4 quad-core processor (likely oversold) and 3GB memory (Xen). We've had problems from the beginning. The server keeps crashing. It seems PHP keeps expanding till it consumes all the memory and crashes the server. Some folks have suggested that I should abandon Apache/cPanel/PHP/mySQL and go with nginX/Varnish/PHP-FPM/SQLite. But that's just not possible for me as I am not very tech savvy and need a simple GUI like cPanel to be able to manage the mundane management tasks (can't afford to hire system administrator or get fully managed hosting). I have come across several posts discussing optimization of Apache for WordPress. But all of these lead to articles that are pretty dated such as this ~4 year old one from Jan 2009 - http://thethemefoundry.com/blog/optimize-apache-wordpress/ The article is pretty detailed and seems helpful, but I stumble even on the first step. My httpd.conf only has 2 loadmodule commands LoadModule fastinclude_module modules/mod_fastinclude.so LoadModule bwlimited_module modules/mod_bwlimited.so So I go total bust right there. Further, my httpd.conf says Direct modifications to the Apache configuration file may be lost upon subsequent regeneration of the configuration file. To have modifications retained, all modifications must be checked into the configuration system by running: /usr/local/cpanel/bin/apache_conf_distiller I am having trouble finding where to change the modules in WHM. Please can someone help me with updated guidelines on how to optimize Apache for WordPress? Many thanks! P.S. The WordPress installation also has WP Super Cache installed. P.P.S. I also have phpBB, OpenCart, and Menalto Gallery installed.

  Read the article

• Nginx redirect all request that does not match a file to a php file

  - by cyrbil

  I'm trying to get all request to: http://mydomain.com/downloads/* redirect to http://mydomain.com/downloads/index.php except if the requested file exist in /downloads/ ex: http://mydomain.com/downloads = /downloads/index.php http://mydomain.com/downloads/unknowfile = /downloads/index.php http://mydomain.com/downloads/existingfile = /downloads/existingfile My current problem is I have either the redirection to php working but static files not served or the opposite. Here is my current vhost conf: (which redirect fine but static files are send to php and fail) server { listen 80; ## listen for ipv4; this line is default and implied server_name domain.com; root /data/www; index index.php index.html; location / { try_files $uri $uri/ /index.html; } error_page 404 /404.html; # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root /usr/share/nginx/www; } location ^~ /downloads { fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_index index.php; include fastcgi_params; try_files $uri @downloads; } location @downloads { rewrite ^ /downloads/index.php; } # pass the PHP scripts to FastCGI server # location ~ \.php$ { try_files $uri =404; fastcgi_split_path_info ^(.+\.php)(/.+)$; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include fastcgi_params; } } Precision: static files are symlinks created by /downloads/index.php Thank you for your help.

  Read the article

• vSphere education - What are the downsides of configuring virtual machines with *too* much RAM?

  - by ewwhite

  VMware memory management seems to be a tricky balancing act. With cluster RAM, Resource Pools, VMware's management techniques (TPS, ballooning, host swapping), in-guest RAM utilization, swapping, reservations, shares and limits, there are a lot of variables. I'm in a situation where clients are using dedicated vSphere cluster resources. However, they are configuring the virtual machines as though they were on physical hardware. In turn, this means a standard VM build may have 4 vCPUs and 16GB or more of RAM. I come from the school of starting small (1 vCPU, minimal RAM), checking real-world use and adjusting up as necessary. Some examples from a "problem" cluster. Resource pool summary - Looks almost 4:1 overcommitted. Note the high amount of ballooned RAM. Resource allocation - The Worst Case Allocation column shows that these VMs would have access to less than 50% of their configured RAM under constrained conditions. The real-time memory utilization graph of the top VM in the listing above. 4 vCPU and 64GB RAM allocated. It averages under 9GB use. Summary of the same VM What are the downsides of overcommitting and overconfiguring resources (specifically RAM) in vSphere environments? Assuming that the VMs can run in less RAM, is it fair to say that there's overhead to configuring virtual machines with more RAM than they need? What is the counter-argument to: "if a VM has 16GB of RAM allocated, but only uses 4GB, what's the problem??"? E.g. do customers need to be educated? What specific metric should be used to meter RAM usage. Tracking the peaks of "Active" versus time?

  Read the article

• Deploying Memcached as 32bit or 64bit?

  - by rlotun

  I'm curious about how people deploy memcached on 64 bit machines. Do you compile a 64bit (standard) memcached binary and run that, or do people compile it in 32bit mode and run N instances (where N = machine_RAM / 4GB)? Consider a recommended deployment of Redis (from the Redis FAQ): Redis uses a lot more memory when compiled for 64 bit target, especially if the dataset is composed of many small keys and values. Such a database will, for instance, consume 50 MB of RAM when compiled for the 32 bit target, and 80 MB for 64 bit! That's a big difference. You can run 32 bit Redis binaries in a 64 bit Linux and Mac OS X system without problems. For OS X just use make 32bit. For Linux instead, make sure you have libc6-dev-i386 installed, then use make 32bit if you are using the latest Git version. Instead for Redis <= 1.2.2 you have to edit the Makefile and replace "-arch i386" with "-m32". If your application is already able to perform application-level sharding, it is very advisable to run N instances of Redis 32bit against a big 64 bit Redis box (with more than 4GB of RAM) instead than a single 64 bit instance, as this is much more memory efficient. Would not the same recommendation also apply to a memcached cluster?

  Read the article

• How to hide files in Apache 2.2 WebDAV Directory listings

  - by mdornsf

  I use Apache 2.2 as WebDAV file server to a bunch of Mac and MS Windows clients. Unfortunately both clutter the filesystem with files like .DS_Store or thumbs.db. Since hte files distract my users i want to hide them from directory listings. Unfortunately the standard way of hiding files in Apache (via IndexIgnore) seems not to work via WebDAV. Is there any other way to hide files?

  Read the article

• Getting wget to dowload only files with specific name patterns

  - by Adi

  I want to use wget to DL some files. I want to DL only files whose name that fit a certain pattern, e.g. ???.txt and not any other *.txt files. Can this be done with wget? I could only find a way to --accept/--reject files based on the extension. Thanks!

  Read the article

• How can access files on shared drive from Windows 2008 server configured with SFTP

  - by communicator

  I have installed OpenSSH on my windows 2008 server by following the user guide here . Now I have some files on windows network share with UNC path as \\corp\test\testdata I want map this file system on network share to my windows 2008 server which is configred with SFTP so that I can access these files from my Java Program by doing SFTP to windows 2008 server.Is there anyway I can map the network share to C or other drive in server so that all the files on the share will be available as local files on the server?

  Read the article

• Good text editors or viewers for large log files

  - by Kristopher Johnson

  Log files and other textual data files are often tens or hundreds of megabytes in size, and some editors choke when you try to open something so large. What are some good applications for viewing large files? Bonus points for apps that can open compressed files, search for things with regular expressions, parse output lines, etc.

  Read the article

• Emacs open files from a filename list

  - by crasic

  I have a largish tex project that is separated into several tex files. Everytime I want to work on it I open emacs and manually C-x C-f all the files that I want to work on. I was wondering if there is a way to open files (from command line) from a file containing a list of filenames, something like filelist.txt: file1.tex file2.tex file3.tex then do cat files | emacs -nw except that emacs doesn't support the command used as it doesn't like that stdin is reassigned. any ideas?

  Read the article

• View/Find all compressed files on the server?

  - by Volodymyr

  I need to find all compressed files/folders regardless of file format on a Windows Server 2003 machine. Search options do not provide this capability. Is there a way to list/view all compressed files? Perhaps, this can be done by PowerShell using file/folder attributes and put into a txt file with file location. UPD: Under compressed files/folders - I mean files which appear in blue color in Explorer after changing file/folder attribute.

  Read the article

• Junk files appeared in my OSX root folder?

  - by user68732

  I see a bunch of junk files in the root folder of my hard drive running Snow Leopard. Here is a screen shot of the files: If I inspect these files, they appear to contain XML with DeviceCertificate, DevicePublicKey, and SystemBUID information, among other XML elements. I do iOS development on this machine. Can anyone explain from where these files came, and if they are an indication of anything serious, such as malware or spyware?

  Read the article

• Cannot share files on USB drive between Windows 98 and Windows 2000

  - by Ken Pespisa

  I've run into a strange situation where I can't share files between Windows 98 and Windows 2000 using a USB flash drive. Files I put on the Win98 machine can be read by that machine, but not by the Win2k machine. And likewise, I can add and read files on that drive from the Win2k machine, but those files don't appear on the drive when accessed from the Win98 machine. Anyone have ideas as to what could be the cause of this?

  Read the article

• How to search inside files in Windows 7?

  - by Revolter

  In Windows XP we can search for files witch contains a defined keyword (inside all files types) Windows 7 can look inside files for a keywords, okay, but only for text files. (*.doc,*.txt, *.inf, ...), not (*.conf, *.dat, *.*, ...) Microsoft search filters don't contain any filter I can use for this. Any idea?

  Read the article

• WINDOWS - Deleting Temporary Internet Files through Group Policy

  - by Muhammad Ali

  I have a domain controller running on Windows 2008 Server R2 and users login to application servers on which Windows 2003 Server SP2 is installed. I have applied a Group Policy to clean temporary internet files on exit i.e to delete all temporary internet files when users close the browser. But the group policy doesn't seem to work as user profile size keeps on increasing and the major space is occupied by temporary internet files therefore increasing the disk usage. How can i enforce automatic deletion of temporary internet files?

  Read the article

< Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >