Search Results

Search found 6703 results on 269 pages for 'amd graphics'.

Page 133/269 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Attach radeon driver to specific PCI devices?

  - by genpfault

  I have two Radeon cards in this machine, a 6570 and a 6950: lspci | grep VGA: 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Turks [Radeon HD 6570] 02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Cayman PRO [Radeon HD 6950] I'm trying to get VGA passthrough to work with KVM on Debian Wheezy, passing through the 6950 as a secondary video card to a Windows 7 guest. This works fine if I blacklist the radeon kernel module via /etc/modprobe.d/. If I remove the blacklist to run X11 (or even just a KMS console) on the 6570 the radeon module seems to attach to both cards: dmesg | egrep "01:00.0|02:00.0|radeon": pci 0000:01:00.0: [1002:6759] type 0 class 0x000300 pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xefffffff 64bit pref] pci 0000:01:00.0: reg 18: [mem 0xf7e20000-0xf7e3ffff 64bit] pci 0000:01:00.0: reg 20: [io 0xe000-0xe0ff] pci 0000:01:00.0: reg 30: [mem 0xf7e00000-0xf7e1ffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:02:00.0: [1002:6719] type 0 class 0x000300 pci 0000:02:00.0: reg 10: [mem 0xd0000000-0xdfffffff 64bit pref] pci 0000:02:00.0: reg 18: [mem 0xf7d20000-0xf7d3ffff 64bit] pci 0000:02:00.0: reg 20: [io 0xd000-0xd0ff] pci 0000:02:00.0: reg 30: [mem 0xf7d00000-0xf7d1ffff pref] pci 0000:02:00.0: supports D1 D2 vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: device added: PCI:0000:02:00.0,decodes=io+mem,owns=none,locks=none vgaarb: bridge control possible 0000:02:00.0 vgaarb: bridge control possible 0000:01:00.0 pci 0000:01:00.0: Boot video device [drm] radeon kernel modesetting enabled. radeon 0000:01:00.0: setting latency timer to 64 radeon 0000:01:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used) radeon 0000:01:00.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF [drm] radeon: 1024M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. radeon 0000:01:00.0: irq 46 for MSI/MSI-X radeon 0000:01:00.0: radeon: using MSI. [drm] radeon: irq initialized. radeon 0000:01:00.0: WB enabled [drm] radeon: ib pool ready. [drm] radeon: power management initialized fbcon: radeondrmfb (fb0) is primary device fb0: radeondrmfb frame buffer device [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on minor 0 radeon 0000:02:00.0: enabling device (0000 -> 0003) radeon 0000:02:00.0: setting latency timer to 64 radeon 0000:02:00.0: VRAM: 2048M 0x0000000000000000 - 0x000000007FFFFFFF (2048M used) radeon 0000:02:00.0: GTT: 512M 0x0000000080000000 - 0x000000009FFFFFFF [drm] radeon: 2048M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. radeon 0000:02:00.0: irq 49 for MSI/MSI-X radeon 0000:02:00.0: radeon: using MSI. [drm] radeon: irq initialized. radeon 0000:02:00.0: WB enabled [drm] radeon: ib pool ready. [drm] radeon: power management initialized fb1: radeondrmfb frame buffer device [drm] Initialized radeon 2.12.0 20080528 for 0000:02:00.0 on minor 1 [drm] radeon: finishing device. radeon 0000:02:00.0: ffff88041a941800 unpin not necessary [drm] radeon: ttm finalized pci-stub 0000:02:00.0: claimed by stub pci-stub 0000:02:00.0: irq 49 for MSI/MSI-X This causes the Win7 VM to bluescreen on boot. How can I configure things so that the radeon module only attaches to the 6570 and not the 6950?

  Read the article

• Why do GPUs overheat?

  - by JAD

  About a year ago, I added a 9800GT (1 GB version) and a Corsair CX500 PSU to an HP M8000N computer. A few weeks ago, the HDD overheated and I decided to transfer the GPU & PSU to a new build, which consists of: i3 @ 3.3Ghz Gigabyte H61 Micro ATX Mobo 4GB RAM 500GB WD HDD DVD RW Drive Cooler Master Elite 430 Tower Once I had Win7 up and running, I installed all the essential drivers that came with the Gigabyte Mobo CD. However, whenever I tried installing the Graphics Media Accelerator driver, the computer would crash and enter an endless boot sequence on the next startup. I skipped installing this driver and installed the CD driver for the 9800GT, which by now is a year old. Everything was working fine, WEI rated my GPU at 6.6 graphics & aero performance. However, after updating my Nvidia drivers to the latest, the WEI dropped my rating to 3.3 for Aero, and 4.7 for graphics performance. Just to make sure that everything was ok, I ran Bad Company 2 on medium settings. The first few minutes ran just fine at a smooth framerate, so I dismissed this as Windows being Windows. About 6 hours later, I ran BC2 again. This time I averaged anywhere from 2-5 FPS. I checked the GPU temperature through GPU-Z, and it came back as 120C. The problem with this, is that the computer was on for six hours up to that point. Wouldn't the card have experienced a reactor core meltdown a lot sooner than that? Granted, the computer was "sleeping" some of the time, but still... The next day I took out a temperature gun and ran some tests. I would point the laser at a very specific area on the reverse side of the card (not the fan or "front"), and compare the temp reading with GPU-Z. After leaving the system on idle on idle for a few minutes, I ran BC2 twice. Here are the results: GPU-Z Reading / Temp Gun Reading / Time Null / 22.3°C / Comp is Off 53°C / 33.5°C / 1:49 78°C / 46°C / 1:53 - (First BC2 run; good framerate) 102°C / 64.6°C / 2:01 - (System is again on idle) 113°C / 64.8°C / 2:10 119°C / 71.8°C / 2:17 - (Second BC2 run; poor framerate) I should also mention that I also took a temp recording of another part of the GPU from 2:01-2:17. The temp in this area jumped from 75°C to 82.9°C in that time frame. This pretty much confirms that GPU-Z is reporting the temperature accurately, and the card is overheating. But I'd like to know why; the cars is doing nothing and still the temperature climbs at a steady rate. I thoroughly cleaned the GPU and PSU when I salvaged them from the old HP M8000N computer with a can of compressed air, dust cant be the issue. Similarly, the rest of the computer is brand new. I installed various Nvidia drivers, but no luck. It seems strange to me that a year-old card is suddenly failing on me; aren't they supposed to last at least two years? Could this be a driver issue? Is the motherboard faulty? Could the PSU be overfeeding the card on voltage? Neither case seems likely, as the CPU, RAM and otherwise the rest of the comp has worked flawlessly and has stayed well within respectable temp ranges (the i3 lingers around 50C, the HDD stays at 30C, so does the PSU). How can I pinpoint the issue?

  Read the article

• Snort install issue on debian 6 with libpcre - libpcre library not found

  - by Chuck

  I've read the manual on snort.org for installing snort on Debian but am still having an issue. Does anyone know how to resolve this? I've tried installing the libpcre3 amd libpcre3-dev packages by using apt-get and also manually installing by downloading the latest version off the tcpdump website. Any ideas? Checking for pcre-compile in -l pcre...no Error! Libpcre library not found. Get it from http://www.pcre.org

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• devcon.exe not working in Windows7 x64

  - by yas4891

  I can't use the ia64-version of devcon.exe on my Windows7 professional x64 (AMD CPU). error message tells me, that the version of this applcation is not suitable for this version of windows and I should check whether I need to use a x64 or x86 version of this application. The x86 version starts correctly, but all operations (remove, restart, disable etc) fail. Running from a command line with full privileges. Any ideas how to solve this?

  Read the article

• Windows 8 - When AC Power is disconnected, atibtmon.exe throws a Runtime error

  - by Junior Mayhé

  The installer is not working for my ATI mobility Radeon HD 3670 on Dell XPS Studio 16 using Windows 8 PRO 64 bits. Here are the screenshots of my ATI Radeon configuration: Hardware configuration Software configuration And here is the problem on Windows 8: everytime I disconnect the AC power cord, atibtmon.exe throws a runtime error as follows What could I do to avoid this error? I have installed the legacy driver http://support.amd.com/us/kbarticles/Pages/catalystlegacywin8.aspx but this installer fails (when trying to install the driver).

  Read the article

• Linux RAID-0 performance doesn't scale up over 1 GB/s

  - by wazoox

  I have trouble getting the max throughput out of my setup. The hardware is as follow : dual Quad-Core AMD Opteron(tm) Processor 2376 16 GB DDR2 ECC RAM dual Adaptec 52245 RAID controllers 48 1 TB SATA drives set up as 2 RAID-6 arrays (256KB stripe) + spares. Software : Plain vanilla 2.6.32.25 kernel, compiled for AMD-64, optimized for NUMA; Debian Lenny userland. benchmarks run : disktest, bonnie++, dd, etc. All give the same results. No discrepancy here. io scheduler used : noop. Yeah, no trick here. Up until now I basically assumed that striping (RAID 0) several physical devices should augment performance roughly linearly. However this is not the case here : each RAID array achieves about 780 MB/s write, sustained, and 1 GB/s read, sustained. writing to both RAID arrays simultaneously with two different processes gives 750 + 750 MB/s, and reading from both gives 1 + 1 GB/s. however when I stripe both arrays together, using either mdadm or lvm, the performance is about 850 MB/s writing and 1.4 GB/s reading. at least 30% less than expected! running two parallel writer or reader processes against the striped arrays doesn't enhance the figures, in fact it degrades performance even further. So what's happening here? Basically I ruled out bus or memory contention, because when I run dd on both drives simultaneously, aggregate write speed actually reach 1.5 GB/s and reading speed tops 2 GB/s. So it's not the PCIe bus. I suppose it's not the RAM. It's not the filesystem, because I get exactly the same numbers benchmarking against the raw device or using XFS. And I also get exactly the same performance using either LVM striping and md striping. What's wrong? What's preventing a process from going up to the max possible throughput? Is Linux striping defective? What other tests could I run?

  Read the article

• Software to check configuration and diagnostic of my PC is well configured

  - by aiacet

  Is there a utility, software or program than can check that my PC is well configured? Features I'm looking for: Checks to see if the communications between all the components works correctly Indicates if the OS is working properly Check the RAM and memory paging is configured correctly My system: AMD Phenom II X4 955 Black Box 125W Asus M4A785TD-M EVO Radeon HD5770 1GB GDDR5 Asus CoolerMaster GX 650W G.Skill 2x2GB PC3-12800 1600Mhz-787 4GBECO Western Digital 1TB SATAII 64MB Windows XP 32bit Antivirus and firewall: F-secure

  Read the article

• Can I run 8 to 12 Monitors from one Laptop?

  - by Dan

  I would like to run at least 8 monitors & possibly 12, from a Dell Precision M6800 mobile Laptop Workstation. Monitors I want to run are Dell U2412M ( 1920x1200 ) Ultra Sharp Monitors. The specs for the Laptop are : Intel Core i7-4700MQ Processor (17.3") UltraSharp FHD(1920x1080) 8GB (2x4GB) 1600MHz DDR3L AMD FirePro M6100 w/2GB GDDR5 2.5 inch 500GB Solid State Hybrid Drive Is it possible to do it & if yes, what other hardware, software do I need besides monitors ? Thanks

  Read the article

• does intel Xeon e5620 have EPT support?

  - by maruti

  looking for CPU with good Virtualization support. could not find Intel EPT (extended page table) technology with E series. Is it only with higher X series? but AMD Magny cour 6134 does have the RVI support (Rapid Virt Indexing)

  Read the article

• Can Windows 2008 64bit make use of a 6 core cpu?

  - by Tony_Henrich

  There's a version of AMD Phenom CPU which is 6 cores. Would Windows 2008 64 bit & SQL Server 2008 64 bit make use of all the cores? Any special settings of the OS or sql server needed to benefit from all the 6 cores?

  Read the article

• Are there any advantages to using windows 7 ultimate? I can't tell the diference

  - by Jack Dawson

  I just upgraded my new desktop which came installed with Windows 7 Home Premium 64 bit with a copy of Windows 7 Ultimate 64 bit and so far I have not noticed any difference in performance. Even my Windows Experience Index number is the same 5.5 that it was before the upgrade. So what's the point, are there any performance advantages that I'm not seeing? Additional Info My system hardware specs: AMD quad core 2.6 GHZ 1 TB 4200 RPM HDD 8 GB DDR2 RAM ATI Radeon HD 4650 w/ 1GB dedicated video memory

  Read the article

• Palit GeForce 8800GT 512MB Minimum Power Requirement?

  - by Wesley

  Hi all, I am building a system for a friend. The potential specs are like this so far: ASUS A8N-VM motherboard AMD Athlon 64 3200+ @ 2.0 GHz Any 7200RPM SATA HDD Palit GeForce 8800GT 512MB GDDR3 PCIe One DVD/CD combo drive Creative SB Live! 5.1 sound card I was wondering what wattage of power supply would be able to support this hardware. I had a 350W in mind... would that do? Thanks in advance.

  Read the article

• Motherboard Is A MCP61PM-HM Rev 1.OB

  - by Dennis Smith

  I have a compaq presario pc SR5110NX The Processor is AMD Athlon 64 Proceessor3800+ It has 512 mb of Ram and a 40gb Hard Drive Here is my problem I Have 2 Sata One Is Black and the other Is White I have 2 red little cables and they have the letters and numbers on them It Is HP P/N:5188-2897 0720 on the side of the cable.Here is the Mother Board MCP61PM-HM Rev 1.0B I need to now where do the two Sata Connectors Connect Too Please Help Thank You So Much.Ps I am running windows XP Pro

  Read the article

• Finding out if hardware virtualisation is enabled in Ubuntu 9.10

  - by Simon Rice

  Is there a way I can determine if hardware virtualisation is enabled in Karmic? I know my processor is capable of it (from knowing it's an AMD Athlon 64 x2 & via something coming out when I type egrep '(vmx|svm)' --color=always /proc/cpuinfo), but I can't tell if I need to flash my bios to enable it.

  Read the article

• Blue screen of death when moving files

  - by kevin

  i just bought a new hp amd II athlon quad core and everytime i try to move file off my desktop to a hard drive or off my hard drive to my desktop of atleast a 1g or more my computer restarts itself and gives me the blue screen of death can someone please tell me why

  Read the article

• SSD and intel i5 lagging

  - by Marek Javurek

  my "new" notebook has some really wierd lags during work, youtube video etc etc... Sometimes it has bluescreen during booting, sometimes after reboot. All my drivers are updated and SSD firmware too. this is my notebook parameters: Operating System MS Windows 7 64-bit SP1 CPU Intel Core i5 @ 2.40GHz: 57 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 665MHz (9-9-9-24) Motherboard LENOVO 12985VG (CPU): 58 °C Graphics SyncMaster (1680x1050@60Hz) AMD Radeon HD 6630M Series (Lenovo) Hard Drives 125GB Crucial M4-CT128M4SSD1 ATA Device (SATA-SSD) full specs here: http://speccy.piriform.com/results/Khr265gWVgk6vKTMrhdfhlS

  Read the article

• what to do if a computer gets a blue screen when trying to install windows xp

  - by Nrew

  What might be the reason why I get blue screen when I try to install windows xp. on a laptop. Specifically an Acer aspire laptop with AMD Processor. What do I do to make it work. Its probably not the Cd, because I've tried it on other computer and it works.

  Read the article

• win7 64 bit. Fresh install on fresh pc fails with BSOD.

  - by 0plus1

  Hello, I've built a new machine: ASUS M4A785TD-V EVO OCZ DDR3 PC3-12800 (2x 2gb) Amd Athlon II X4 630 Box AM3 I tried memtest with hiren boot cd (tested only 3gb) and showed no error. Then I tried the built in ram test from the win7 cd (2 passes no errors). I also deleted with a 0 pass the hard drive. The error I get is this: 0x0000007e (0xFFFFFFFFFC0000005,0xFFFFF8000C1AB0F3,0xFFFFF880009A8498,0xFFFFF880009A7CF0) Any help is greatly appreciated. Thank you!

  Read the article

• Mac OS X as guest on VirtualBox with Ubuntu Host?

  - by johnlai2004

  I have a legitimate copy of Mac OS X. I want to install Ubuntu on my new AMD computer as my host OS, then install Mac OS X as the guest OS via VirtualBox. Does anyone know if this will be an easy thing to do? Will I need some kind of hack job to get OS X working via VirtualBox?

  Read the article

• Real performance gain from faster IDE or SATA hard drive?

  - by raw_noob

  How much of a real-world performance gain would you expect from: replacing a 5400rpm IDE HD with a 7200rpm IDE HD? replacing a 5400rpm IDE HD with a SATA-150? It's assumed that the drive in question is both the system drive and the only drive. A modest AMD Sempron-based home computer with adequate DDR memory running Windows XP Home SP3. Thanks for looking.

  Read the article

• Is this build compatible?

  - by Jephir

  I am building a new computer with this configuration: Foxconn AM3 Micro ATX AMD Phenom II X6 A-DATA 4GB DDR3 Radeon HD 5870 OCZ Fatal1ty 550W Power Supply Cooler Master Elite 310 Red Mid Tower Case I am reusing my old SATA hard drive and DVD drive. Is this build compatible?

  Read the article

• Cannot get sound in Windows 7 - No audio devices are installed

  - by bobsr

  Just installed Windows 7. After install everything was working fine until i noticed that i had no sound. It is a AMD Athlon x64 Dual Sound works in XP, has these sound drivers Yamaha DS1 WDM HD Audio Render I tried finding the above drivers, but no luck.

  Read the article

• How to get the best LINPACK result and conquer the Top500?

  - by knweiss

  Given a large Linux HPC cluster with hundreds/thousands of nodes. What are your best practices to get the best possible LINPACK benchmark (HPL) result to submit for the Top500 supercomputer list? To give you an idea what kind of answers I would appreciate here are some sub-questions (with links): How to you tune the parameters (N, NB, P, Q, memory-alignment, etc) for the HPL.dat file (without spending too much time trying each possible permutation - esp with large problem sizes N)? Are there any Top500 submission rules to be aware of? What is allowed, what isn't? Which MPI product, which version? Does it make a difference? Any special host order in your MPI machine file? Do you use CPU pinning? How to you configure your interconnect? Which interconnect? Which BLAS package do you use for which CPU model? (Intel MKL, AMD ACML, GotoBLAS2, etc.) How do you prepare for the big run (on all nodes)? Start with small runs on a subset of nodes and then scale up? Is it really necessary to run LINPACK with a big run on all of the nodes (or is extrapolation allowed)? How do you optimize for the latest Intel/AMD CPUs? Hyperthreading? NUMA? Is it worth it to recompile the software stack or do you use precompiled binaries? Which settings? Which compiler optimizations, which compiler? (What about profile-based compilation?) How to get the best result given only a limited amount of time to do the benchmark run? (You can block a huge cluster forever) How do you prepare the individual nodes (stopping system daemons, freeing memory, etc)? How do you deal with hardware faults (ruining a huge run)? Are there any must-read documents or websites about this topic? E.g. I would love to hear about some background stories of some of the current Top500 systems and how they did their LINPACK benchmark. I deliberately don't want to mention concrete hardware details or discuss hardware recommendations because I don't want to limit the answers. However, feel free to mention hints e.g. for specific CPU models.

  Read the article

• Cassandra on heterogeneous servers

  - by happy-coding

  I am currently running 4 cassandra nodes with the following hardware in a Apache Cassandra cluster: AMD Athlon 64 X2 6000+ 8G RAM 750G hard disk It shows not such a good writing performance and a really bad read performance with sometimes also timeouts. I was wondering if it makes sense to add 2 nodes with a different hardware (8 CPUs and more RAM) to improve this. Or does a cassandra cluster works best with the same hardware in every node? Thanks & best regards

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >