Search Results

Search found 18025 results on 721 pages for 'blue screen'.

Page 133/721 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

  • Are these three brand new sticks of RAM really dead?

    - by David Brown
    I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

    Read the article

  • How to exclude a sub-folder from HTaccess RewriteRule

    - by amb9800
    I have WordPress installed in my root directory, for which a RewriteRule is in place. I need to password-protect a subfolder ("blue"), so I set the htaccess in that folder as such. Problem is that the root htaccess RewriteRule is applying to "blue" and thus I get a 404 in the main WordPress site (instead of opening the password dialog for the subfolder). Here's the root htaccess: RewriteEngine on <Files 403.shtml> order allow,deny allow from all </Files> <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> I tried inserting this as the second line, to no avail: RewriteRule ^(blue)($|/) - [L] Also tried inserting this before the index.php RewriteRule: RewriteCond %{REQUEST_URI} !^/blue/ That didn't work either. Also inserted this into the subfolder's htaccess, which didn't work either: <IfModule mod_rewrite.c> RewriteEngine off </IfModule> Any ideas?

    Read the article

  • How to disable color dithering for low-bit-depth screen settings?

    - by gogowitsch
    I am using Terminal Services and TeamViewer a lot to access other computers, partly over slow networks. The problem described below is not affected by which of the two remote access services I am using. When accessing Windows 7 Professional machines, a great deal of text is hard to read as the background is dithered. Even for exactly the same colors, Windows 2003 does not seem to dither at all, but to choose the closest available color. I strongly prefer the latter, as I don't care for the exact colors, I just want to be able to read easily. I am not sure whether this is operating system-related. The programs on the remote systems do not allow me to change the color choices for the various backgrounds to anything sane. Is there a way to disable this color dithering using some target operating system setting that will do the trick for both Terminal Services and TeamViewer?

    Read the article

  • Gimp: change one colour to another?

    - by AP257
    Simple to explain: possibly not so simple to do. In Gimp, I have a green button GIF image: it shades from dark green to light green, against a transparent background. I would like to change it to blue, and keep the shading, so it shades from dark blue to light blue. Anyone know how I can do this? Can't find an explanation by Googling! Thanks.

    Read the article

  • How to setup a Linux machine to remotely use laptop screen as a second display?

    - by Ignas Limanauskas
    I am looking for a similar solution to MaxiVista, but for Linux (Ubuntu). I have an Ubuntu machine with just one display attached, but I also have a Windows laptop running a virtual machine with Ubuntu installed. I figured there must be a way to trick the main Ubuntu machine remotely use the virtual machine's display capabilities. After all, X11 does support forwarding and things like that. Any ideas how to do it using VNC? I saw some references to xdmx, but instructions so far are vague and do not seem to work on my machine(s).

    Read the article

  • Can Windows 7 place a task bar on each monitor, which only shows applications running on that screen

    - by OverloadUT
    I would like to have a task bar on each of my monitors, but I only want applications that are currently on that monitor to be displayed on its taskbar. This can be accomplished using UltraMon, however the taskbar shown on the secondary and tertiary monitors is not the native Windows 7 taskbar, but rather made to try to simulate how it looks and feels. As good as it is, it is missing a ton of the features I find best about the taskbar, such as program grouping, "peeking" at applications and so forth. So I am wondering if there is a way to make Windows 7 actually display its native awesome taskbar on multiple monitors.

    Read the article

  • Indicating end of Standard Input

    - by waiwai933
    How does one indicate that one has finished entering test in stdin? For example, let's say that I wish to encrypt 'blue' using MD5 (I know MD5 is unsecure, but just for this example). I tried user$ blue | md5 which I was led to understand is how one pipes input to stdin, but it doesn't work right. But if I just enter user$ md5 I can enter the word 'blue'. But how do I indicate to md5 that I'm finished entering text?

    Read the article

  • Debian Based Server not booting, soon after GRUB screen it restarts?

    - by Krauser
    I have tried running memtest, it start get about half way then abruptly restarts. I assume this is not a problem with the OS itself but rather a hardware issue, I have checked various logs when after about 10 reboots it starts ok, /var/log/kern.log /var/log/syslog /var/log/dmesg All I get is: EXT4-fs(sdc1): re-mounted. Opts: errors=remount-ro restart So I ran fcsk on the drive, to check if the fs was failing and it was fine. Really don't know how to find why the server is continuosly restarting andif I get lucky it will boot up.

    Read the article

  • How to change the order of OS's on my boot screen on a dual boot setup?

    - by th3dude19
    I'm running a dual boot configuration on my laptop using Ubuntu 10.04b and Windows 7 Home Premium. Windows 7 was the original OS and I added a 'side by side' installation of Ubuntu. Ubuntu, however, shows up first on the list. I'd like to change this order and make Windows 7 first, followed by Ubunutu, then all of the recovery boots after that. Any help on how this is done?

    Read the article

  • Raspberry Pi entrance signed backed by Umbraco - Part 1

    - by Chris Houston
    Being experts on all things Umbraco, we jumped at the chance to help our client, QV Offices, with their pressing signage predicament. They needed to display a sign in the entrance to their building and approached us for our advice. Of course it had to be electronic: displaying multiple names of their serviced office clients, meeting room bookings and on-the-pulse promotions. But with a winding Victorian staircase and minimal storage space how could the monitor be run, updated and managed? That’s where we came in…Raspberry PiUmbraco CMSAutomatic updatesAutomated monitor of the signPower saving when the screen is not in useMounting the screenThe screen that has been used is a standard LED low energy Full HD screen and has been mounted on the wall using it's VESA mounting points, as the wall is a stud wall we were able to add an access panel behind the screen to feed through the mains, HDMI and sensor cables.The Raspberry Pi is then tucked away out of sight in the main electrical cupboard which just happens to be next to the sign, we had an electrician add a power point inside this cupboard to allow us to power the screen and the Raspberry Pi.Designing the interface and editing the contentAlthough a room sign was the initial requirement from QV Offices, their medium term goal has always been to add online meeting booking to their website and hence we suggested adding information about the current and next day's meetings to the sign that would be pulled directly from their online booking system.We produced the design and built the web page to fit exactly on a 1920 x 1080 screen (Full HD in Portrait)As you would expect all the information can be edited via an Umbraco CMS, they are able to add floors, rooms, clients and virtual clients as well as add meeting bookings to their meeting diary.How we configured the Raspberry PiAfter receiving a new Raspberry Pi we downloaded the latest release of Raspbian operating system and followed the official guide which shows how to copy the OS onto an SD card from a Mac, we then followed the majority of steps on this useful guide: 10 Things to Do After Buying a Raspberry Pi.Installing ChromiumWe chose to use the Chromium web browser which for those who do not know is the open sourced version of Google Chrome. You can install this from the terminal with the following command:sudo apt-get install chromium-browserInstalling UnclutterWe found this little application which automatically hides the mouse pointer, it is used in the script below and is installed using the following command:sudo apt-get install unclutterAuto start Chromium and disabling the screen saver, power saving and mouseWhen the Raspberry Pi has been installed it will not have a keyboard or mouse and hence if their was a power cut we needed it to always boot and re-loaded Chromium with the correct URL.Our preferred command line text editor is Nano and I have assumed you know how to use this editor or will be able to work it out pretty quickly.So using the following command:sudo nano /etc/xdg/lxsession/LXDE/autostartWe then changed the autostart file content to:@lxpanel --profile LXDE@pcmanfm --desktop --profile LXDE@xscreensaver -no-splash@xset s off@xset -dpms@xset s noblank@chromium --kiosk --incognito http://www.qvoffices.com/someURL@unclutter -idle 0The first few commands turn off the screen saver and power saving, we then open Cromium in Kiosk Mode (full screen with no menu etc) and pass in the URL to use (I have changed the URL in this example) We found a useful blog post with the Cromium command line switches.Finally we also open an application called Unclutter which auto hides the mouse after 0 seconds, so you will never see a mouse on the sign.We also had to edit the following file:sudo nano /etc/lightdm/lightdm.confAnd added the following line under the [SeatDefault] section:xserver-command=X -s 0 dpmsRefreshing the screenWe decided to try and add a scheduled task that would trigger Chromium to reload the page, at some point in the future we might well change this to using Javascript to update the content, but for now this works fine.First we installed the XDOTool which enables you to script Keyboard commands:sudo apt-get install xdotoolWe used the Refreshing Chromium Browser by Shell Script post as a reference and created the following shell script (which we called refreshing.sh):export DISPLAY=":0"WID=$(xdotool search --onlyvisible --class chromium|head -1)xdotool windowactivate ${WID}xdotool key ctrl+F5This selects the correct display and then sends a CTRL + F5 to refresh Chromium.You will need to give this file execute permissions:chmod a=rwx refreshing.shNow we have the script file setup we just need to schedule it to call this script periodically which is done by using Crontab, to edit this you use the following command:crontab -eAnd we added the following:*/5 * * * * DISPLAY=":.0" /home/pi/scripts/refreshing.sh >/home/pi/cronlog.log 2>&1This calls our script every 5 minutes to refresh the display and it logs any errors to the cronlog.log file.SummaryQV Offices now have a richer and more manageable booking system than they did before we started, and a great new sign to boot.How could we make sure that the sign was running smoothly downstairs in a busy office centre? A second post will follow outlining exactly how Vizioz enabled QV Offices to monitor their sign simply and remotely, from the comfort of their desks.

    Read the article

  • SQL – Quick Start with Admin Sections of NuoDB – Manage NuoDB Database

    - by Pinal Dave
    In the yesterday’s blog post we have seen that it is extremely easy to install the NuoDB database on your local machine. Now that the application is properly set up, let us explore NuoDB a bit more and get you familiar with the how it works and what the important areas of the NuoDB are that you should learn. As we have already installed NuoDB, now we will quickly start with two of the important areas in NuoDB: 1) Admin and 2) Explorer. In this blog post I will explore how the Admin Section of the NuoDB Console works.  In the next blog post we will learn how the Explorer Section works. Let us go to the NuoDB Console by typing the following URL in your browser: http://localhost:8080/ It will bring you to the following screen: On this screen you can see a big Start QuickStart button. Click on the button and it will bring you to following screen. On this screen you will find very important information about Domain and Database Settings. It is our habit that we do not read what is written on the screen and keep on clicking on continue without reading. While we are familiar with most wizards, we can often miss the very important message on the screen. Please note the information of Domain Settings and Database Settings from the following screen before clicking on Create Database. Domain Settings User: quickstart Password: quickstart Database Settings User: dba Password: goalie Database: test Schema: HOCKEY Once you click on the Create Database button it will immediately start creating sample database. First, it will start a Storage Manager and right after that it will start a Transaction Engine. Once the engine is up, it will Create a Schema and Sample Data. On the success of the creating the sample database it will show the following screen. Now is the time where we can explore the NuoDB Admin or NuoDB Explorer. If you click on Admin, it will first show following login screen. Enter for the username “domain” and for the password “bird”. Alternatively you can enter “quickstart”  twice for username and password.  It works as too. Once you enter into the Admin Section, on the left side you can see information about NuoDB and Admin Console and on the right side you can see the domain overview area. From this Administrative section you can do any of the following tasks: Create a view of the entire domain Add and remove databases Start and stop NuoDB Transaction Engines and Storage Managers Monitor transaction across all the NuoDB databases On the right side of the Admin Section we can see various information about a particular NuoDB domain. You can quickly view various alerts, find out information about the number of host machines that are provisioned for the domain, and see the number of databases and processes that are running in the domain. If you click on the “1 host” link you will be able to see various processes, CPU usage and other information. In the Processes Section you can see that there are two different types of processes. The first process (where you can see the floppy drive icon) represents a running Storage Manager process and the second process a running Transaction Engine process. You can click on the links for the Storage Manager and Transaction Engine to see further statistical details right down to the last byte of the data. There are various charts available for analysis as well. I think the product is quite mature and the user can add different monitor charts to the Admin section. Additionally, the Admin section is the place where you can create and manage new databases. I hope today’s tutorial gives you enough confidence that you can try out NuoDB and checkout various administrative activities with the database. I am personally impressed with their dashboard related to various counters. For more information about how the NuoDB architecture works and what a Storage Manager or Transaction Engine does, check out this short video with NuoDB CTO Seth Proctor:  In the next blog post, we will try out the Explorer section of NuoDB, which allows us to run SQL queries and write SQL code.  Meanwhile, I strongly suggest you download and install NuoDB and get yourself familiar with the product. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Big Data, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology Tagged: NuoDB

    Read the article

  • How to use caching to increase render performance?

    - by Christian Ivicevic
    First of all I am going to cover the basic design of my 2d tile-based engine written with SDL in C++, then I will point out what I am up to and where I need some hints. Concept of my engine My engine uses the concept of GameScreens which are stored on a stack in the main game class. The main methods of a screen are usually LoadContent, Render, Update and InitMultithreading. (I use the last one because I am using v8 as a JavaScript bridge to the engine. The main game loop then renders the top screen on the stack (if there is one; otherwise, it exits the game) - actually it calls the render methods, but stores all items to be rendered in a list. After gathering all this information the methods like SDL_BlitSurface are called by my GameUIRenderer which draws the enqueued content and then draws some overlay. The code looks like this: while(Game is running) { Handle input if(Screens on stack == 0) exit Update timer etc. Clear the screen Peek the screen on the stack and collect information on what to render Actually render the enqueue screen stuff and some overlay etc. Flip the screen } The GameUIRenderer uses as hinted a std::vector<std::shared_ptr<ImageToRender>> to hold all necessary information described by this class: class ImageToRender { private: SDL_Surface* image; int x, y, w, h, xOffset, yOffset; }; This bunch of attributes is usually needed if I have a texture atlas with all tiles in one SDL_Surface and then the engine should crop one specific area and draw this to the screen. The GameUIRenderer::Render() method then just iterates over all elements and renders them something like this: std::for_each( this->m_vImageVector.begin(), this->m_vImageVector.end(), [this](std::shared_ptr<ImageToRender> pCurrentImage) { SDL_Rect rc = { pCurrentImage->x, pCurrentImage->y, 0, 0 }; // For the sake of simplicity ignore offsets... SDL_Rect srcRect = { 0, 0, pCurrentImage->w, pCurrentImage->h }; SDL_BlitSurface(pCurrentImage->pImage, &srcRect, g_pFramework->GetScreen(), &rc); } ); this->m_vImageVector.clear(); Current ideas which need to be reviewed The specified approach works really good and IMHO it is really has a good structure, however the performance could be definitely increased. I would like to know what do you suggest, how to implement efficient caching of surfaces etc so that there is no need to redraw the same scene over and over again? The map itself would be almost static, only when the player moves, we would need to move the map. Furthermore animated entities would either require updates of the whole map or updates of only the specific areas the entities are currently moving in. My first approaches were to include a flag IsTainted which should be used by the GameUIRenderer to decide whether to redraw everything or use cached version (or to not render anything so that we do not have to Clear the screen and let the last frame persist). However this seems to be quite messy if I have to manually handle in my Render method of the screen class if something has changed or not.

    Read the article

  • Startup/Shutdown time in Xubuntu is increasing!

    - by Ankit
    I am a novice Xubuntu user on a dual-boot machine. The other OS I have is Windows 7. When I first began using Xubuntu, I had really fast startup and shutdown (much much faster than Windows 7 :) ). However, as I started using it more and more for my work, these times started rising. I do not have any problems with execution speed of running applications. My main concern is the shutdown time. Now it has gone above Windows shutdown time [startup time has only partially increase compared to shutdown]. I checked some similar questions like this. However, they seem to not answer my concern as I feel that the concerned users there experience a long wait before the screen goes blue. In my case, the screen goes blue (desktop session ends a blue screen with a moving slider appears) pretty fast. However, it remains blue for a long time. Another answer that I saw on google was to use dmesg and then stopping some services that I do not want. However, me being a novice could not completely understand what it meant

    Read the article

  • Showing content from pages at different URL's (masking), possibly with .htaccess

    - by zigojacko
    If I have URL's like:- domain.com/category/widgets/filter/blue domain.com/category/widgets/filter/red And it is pretty difficult to reconstruct them to something like:- domain.com/category/blue-widgets domain.com/category/red-widgets Is there any way at all that I can use URL rewrites or anything else with .htaccess or on the server to display the URL's as the domain.com/category/blue-widgets on the domain.com/category/widgets/filter/blue page? I've looked into masking URL's but got nowhere and this has been something bugging me for almost 6 months now. Is there any way to achieve what I want to do? FYI: This is a Magento website and the above process, I am wanting to implement for potentially hundreds of URL's. Edit To respond to @kkugelmann's answer:- I couldn't get your proposed RewriteRule to make a difference at all in the .htaccess file so I started testing a few things in this .htaccess tester:- The proposed RewriteRule didn't work in this tester:- However, the following did:- But adding any of these RewriteRule's into the website's .htaccess file did not rewrite the URL at all... Edit2 By the way, if I add [R=301,L] to the end of the URL rewrite rule, it does actually then rewrite the rule, but of course 301 redirects it as well which is unwanted behaviour. Edit3 I found another question with the same issue... And an accepted answer that solved the problem which seemed to be something to do with using mod_proxy and the [P] tag on the rule (if I try this, the page 404's).

    Read the article

  • Streamed mp3 only plays for 1 second

    - by angel6
    Hi, I'm using the plaympeg.c (modified) code of smpeg as a media player. I've got ffserver running as a streaming server. I'm a streaming an mp3 file over http. But when I run plaympeg.c, it plays the streamed file only for a second. When I run plaympeg again, it starts off from where it left and plays for 1 second. Does anyone know why this happens an how to fix it? I've tested it out on WMP and it plays the entire file in one go. So, i guess it's not a problem with the streaming or ffserver.conf include include include include /* #ifdef unix */ include include include include include include include define NET_SUPPORT /* General network support */ define HTTP_SUPPORT /* HTTP support */ ifdef NET_SUPPORT include include include include endif include "smpeg.h" ifdef NET_SUPPORT int tcp_open(char * address, int port) { struct sockaddr_in stAddr; struct hostent * host; int sock; struct linger l; memset(&stAddr,0,sizeof(stAddr)); stAddr.sin_family = AF_INET ; stAddr.sin_port = htons(port); if((host = gethostbyname(address)) == NULL) return(0); stAddr.sin_addr = *((struct in_addr *) host-h_addr_list[0]) ; if((sock = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP)) < 0) return(0); l.l_onoff = 1; l.l_linger = 5; if(setsockopt(sock, SOL_SOCKET, SO_LINGER, (char*) &l, sizeof(l)) < 0) return(0); if(connect(sock, (struct sockaddr *) &stAddr, sizeof(stAddr)) < 0) return(0); return(sock); } ifdef HTTP_SUPPORT int http_open(char * arg) { char * host; int port; char * request; int tcp_sock; char http_request[1024]; char c; printf("\nin http_open passed parameter = %s\n",arg); /* Check for URL syntax */ if(strncmp(arg, "http://", strlen("http://"))) return(0); /* Parse URL */ port = 80; host = arg + strlen("http://"); if((request = strchr(host, '/')) == NULL) return(0); request++ = 0; if(strchr(host, ':') != NULL) / port is specified */ { port = atoi(strchr(host, ':') + 1); *strchr(host, ':') = 0; } /* Open a TCP socket */ if(!(tcp_sock = tcp_open(host, port))) { perror("http_open"); return(0); } /* Send HTTP GET request */ sprintf(http_request, "GET /%s HTTP/1.0\r\n" "User-Agent: Mozilla/2.0 (Win95; I)\r\n" "Pragma: no-cache\r\n" "Host: %s\r\n" "Accept: /\r\n" "\r\n", request, host); send(tcp_sock, http_request, strlen(http_request), 0); /* Parse server reply */ do read(tcp_sock, &c, sizeof(char)); while(c != ' '); read(tcp_sock, http_request, 4*sizeof(char)); http_request[4] = 0; if(strcmp(http_request, "200 ")) { fprintf(stderr, "http_open: "); do { read(tcp_sock, &c, sizeof(char)); fprintf(stderr, "%c", c); } while(c != '\r'); fprintf(stderr, "\n"); return(0); } return(tcp_sock); } endif endif void update(SDL_Surface *screen, Sint32 x, Sint32 y, Uint32 w, Uint32 h) { if ( screen-flags & SDL_DOUBLEBUF ) { SDL_Flip(screen); } } /* Flag telling the UI that the movie or song should be skipped */ int done; void next_movie(int sig) { done = 1; } int main(int argc, char *argv[]) { int use_audio, use_video; int fullscreen; int scalesize; int scale_width, scale_height; int loop_play; int i, pause; int volume; Uint32 seek; float skip; int bilinear_filtering; SDL_Surface *screen; SMPEG *mpeg; SMPEG_Info info; char *basefile; SDL_version sdlver; SMPEG_version smpegver; int fd; char buf[32]; int status; printf("\nchecking command line options "); /* Get the command line options */ use_audio = 1; use_video = 1; fullscreen = 0; scalesize = 1; scale_width = 0; scale_height = 0; loop_play = 0; volume = 100; seek = 0; skip = 0; bilinear_filtering = 0; fd = 0; for ( i=1; argv[i] && (argv[i][0] == '-') && (argv[i][1] != 0); ++i ) { if ( strcmp(argv[i], "--fullscreen") == 0 ) { fullscreen = 1; } else if ((strcmp(argv[i], "--seek") == 0)||(strcmp(argv[i], "-S") == 0)) { ++i; if ( argv[i] ) { seek = atol(argv[i]); } } else if ((strcmp(argv[i], "--volume") == 0)||(strcmp(argv[i], "-v") == 0)) { ++i; if (i >= argc) { fprintf(stderr, "Please specify volume when using --volume or -v\n"); return(1); } if ( argv[i] ) { volume = atoi(argv[i]); } if ( ( volume < 0 ) || ( volume 100 ) ) { fprintf(stderr, "Volume must be between 0 and 100\n"); volume = 100; } } else { fprintf(stderr, "Warning: Unknown option: %s\n", argv[i]); } } printf("\nuse video = %d, use audio = %d\n",use_video, use_audio); printf("\ngoing to check input parameters\n"); if defined(linux) || defined(FreeBSD) /* Plaympeg doesn't need a mouse */ putenv("SDL_NOMOUSE=1"); endif /* Play the mpeg files! */ status = 0; for ( ; argv[i]; ++i ) { /* Initialize SDL */ if ( use_video ) { if ((SDL_Init(SDL_INIT_VIDEO) < 0) || !SDL_VideoDriverName(buf, 1)) { fprintf(stderr, "Warning: Couldn't init SDL video: %s\n", SDL_GetError()); fprintf(stderr, "Will ignore video stream\n"); use_video = 0; } printf("\ninitialised video\n"); } if ( use_audio ) { if ((SDL_Init(SDL_INIT_AUDIO) < 0) || !SDL_AudioDriverName(buf, 1)) { fprintf(stderr, "Warning: Couldn't init SDL audio: %s\n", SDL_GetError()); fprintf(stderr, "Will ignore audio stream\n"); use_audio = 0; } } /* Allow Ctrl-C when there's no video output */ signal(SIGINT, next_movie); printf("\nchecking defined supports\n"); /* Create the MPEG stream */ ifdef NET_SUPPORT printf("\ndefined NET_SUPPORT\n"); ifdef HTTP_SUPPORT printf("\ndefined HTTP_SUPPORT\n"); /* Check if source is an http URL */ printf("\nabout to call http_open\n"); printf("\nhere we go\n"); if((fd = http_open(argv[i])) != 0) mpeg = SMPEG_new_descr(fd, &info, use_audio); else endif endif { if(strcmp(argv[i], "-") == 0) /* Use stdin for input */ mpeg = SMPEG_new_descr(0, &info, use_audio); else mpeg = SMPEG_new(argv[i], &info, use_audio); } if ( SMPEG_error(mpeg) ) { fprintf(stderr, "%s: %s\n", argv[i], SMPEG_error(mpeg)); SMPEG_delete(mpeg); status = -1; continue; } SMPEG_enableaudio(mpeg, use_audio); SMPEG_enablevideo(mpeg, use_video); SMPEG_setvolume(mpeg, volume); /* Print information about the video */ basefile = strrchr(argv[i], '/'); if ( basefile ) { ++basefile; } else { basefile = argv[i]; } if ( info.has_audio && info.has_video ) { printf("%s: MPEG system stream (audio/video)\n", basefile); } else if ( info.has_audio ) { printf("%s: MPEG audio stream\n", basefile); } else if ( info.has_video ) { printf("%s: MPEG video stream\n", basefile); } if ( info.has_video ) { printf("\tVideo %dx%d resolution\n", info.width, info.height); } if ( info.has_audio ) { printf("\tAudio %s\n", info.audio_string); } if ( info.total_size ) { printf("\tSize: %d\n", info.total_size); } if ( info.total_time ) { printf("\tTotal time: %f\n", info.total_time); } /* Set up video display if needed */ if ( info.has_video && use_video ) { const SDL_VideoInfo *video_info; Uint32 video_flags; int video_bpp; int width, height; /* Get the "native" video mode */ video_info = SDL_GetVideoInfo(); switch (video_info->vfmt->BitsPerPixel) { case 16: case 24: case 32: video_bpp = video_info->vfmt->BitsPerPixel; break; default: video_bpp = 16; break; } if ( scale_width ) { width = scale_width; } else { width = info.width; } width *= scalesize; if ( scale_height ) { height = scale_height; } else { height = info.height; } height *= scalesize; video_flags = SDL_SWSURFACE; if ( fullscreen ) { video_flags = SDL_FULLSCREEN|SDL_DOUBLEBUF|SDL_HWSURFACE; } video_flags |= SDL_ASYNCBLIT; video_flags |= SDL_RESIZABLE; screen = SDL_SetVideoMode(width, height, video_bpp, video_flags); if ( screen == NULL ) { fprintf(stderr, "Unable to set %dx%d video mode: %s\n", width, height, SDL_GetError()); continue; } SDL_WM_SetCaption(argv[i], "plaympeg"); if ( screen->flags & SDL_FULLSCREEN ) { SDL_ShowCursor(0); } SMPEG_setdisplay(mpeg, screen, NULL, update); SMPEG_scaleXY(mpeg, screen->w, screen->h); } else { SDL_QuitSubSystem(SDL_INIT_VIDEO); } /* Set any special playback parameters */ if ( loop_play ) { SMPEG_loop(mpeg, 1); } /* Seek starting position */ if(seek) SMPEG_seek(mpeg, seek); /* Skip seconds to starting position */ if(skip) SMPEG_skip(mpeg, skip); /* Play it, and wait for playback to complete */ SMPEG_play(mpeg); done = 0; pause = 0; while ( ! done && ( pause || (SMPEG_status(mpeg) == SMPEG_PLAYING) ) ) { SDL_Event event; while ( use_video && SDL_PollEvent(&event) ) { switch (event.type) { case SDL_VIDEORESIZE: { SDL_Surface *old_screen = screen; SMPEG_pause(mpeg); screen = SDL_SetVideoMode(event.resize.w, event.resize.h, screen->format->BitsPerPixel, screen->flags); if ( old_screen != screen ) { SMPEG_setdisplay(mpeg, screen, NULL, update); } SMPEG_scaleXY(mpeg, screen-w, screen-h); SMPEG_pause(mpeg); } break; case SDL_KEYDOWN: if ( (event.key.keysym.sym == SDLK_ESCAPE) || (event.key.keysym.sym == SDLK_q) ) { // Quit done = 1; } else if ( event.key.keysym.sym == SDLK_RETURN ) { // toggle fullscreen if ( event.key.keysym.mod & KMOD_ALT ) { SDL_WM_ToggleFullScreen(screen); fullscreen = (screen-flags & SDL_FULLSCREEN); SDL_ShowCursor(!fullscreen); } } else if ( event.key.keysym.sym == SDLK_UP ) { // Volume up if ( volume < 100 ) { if ( event.key.keysym.mod & KMOD_SHIFT ) { // 10+ volume += 10; } else if ( event.key.keysym.mod & KMOD_CTRL ) { // 100+ volume = 100; } else { // 1+ volume++; } if ( volume 100 ) volume = 100; SMPEG_setvolume(mpeg, volume); } } else if ( event.key.keysym.sym == SDLK_DOWN ) { // Volume down if ( volume 0 ) { if ( event.key.keysym.mod & KMOD_SHIFT ) { volume -= 10; } else if ( event.key.keysym.mod & KMOD_CTRL ) { volume = 0; } else { volume--; } if ( volume < 0 ) volume = 0; SMPEG_setvolume(mpeg, volume); } } else if ( event.key.keysym.sym == SDLK_PAGEUP ) { // Full volume volume = 100; SMPEG_setvolume(mpeg, volume); } else if ( event.key.keysym.sym == SDLK_PAGEDOWN ) { // Volume off volume = 0; SMPEG_setvolume(mpeg, volume); } else if ( event.key.keysym.sym == SDLK_SPACE ) { // Toggle play / pause if ( SMPEG_status(mpeg) == SMPEG_PLAYING ) { SMPEG_pause(mpeg); pause = 1; } else { SMPEG_play(mpeg); pause = 0; } } else if ( event.key.keysym.sym == SDLK_RIGHT ) { // Forward if ( event.key.keysym.mod & KMOD_SHIFT ) { SMPEG_skip(mpeg, 100); } else if ( event.key.keysym.mod & KMOD_CTRL ) { SMPEG_skip(mpeg, 50); } else { SMPEG_skip(mpeg, 5); } } else if ( event.key.keysym.sym == SDLK_LEFT ) { // Reverse if ( event.key.keysym.mod & KMOD_SHIFT ) { } else if ( event.key.keysym.mod & KMOD_CTRL ) { } else { } } else if ( event.key.keysym.sym == SDLK_KP_MINUS ) { // Scale minus if ( scalesize > 1 ) { scalesize--; } } else if ( event.key.keysym.sym == SDLK_KP_PLUS ) { // Scale plus scalesize++; } else if ( event.key.keysym.sym == SDLK_f ) { // Toggle filtering on/off if ( bilinear_filtering ) { SMPEG_Filter *filter = SMPEGfilter_null(); filter = SMPEG_filter( mpeg, filter ); filter-destroy(filter); bilinear_filtering = 0; } else { SMPEG_Filter *filter = SMPEGfilter_bilinear(); filter = SMPEG_filter( mpeg, filter ); filter-destroy(filter); bilinear_filtering = 1; } } break; case SDL_QUIT: done = 1; break; default: break; } } SDL_Delay(1000/2); } SMPEG_delete(mpeg); } SDL_Quit(); if defined(HTTP_SUPPORT) if(fd) close(fd); endif return(status); }

    Read the article

  • HELP!!! Upgrading to windows 2008 R2 server has caused major issue with screen scraping remote serve

    - by bobsov534
    I have three servers. One is Windows 2003(A) and another is Windows 2008(B) and third one is also Windows 2008 (C). All of them are web servers. A and B contains classic asp pages and they are 32 bit servers and C contains asp.net pages and is 64 bit server. The asp pages of A and B use the screen scraping technology to render the asp.net pages from C. When A is ran, the asp.net page is rendered fine, meaning there are no broken images or file not found error. When B is ran, the images appears to be broken because its looking for those images in Server B instead of Server C itself. I believe this issue is caused by IIS 7 or 7.5 since IIS 6 has no problem scraping the remote server pages. Can you please help me with solution to this problem? This is sort of urgent since upgrading to windows server 2008 R2 now has been a major show stopper for us at the moment. Thanks in advance.

    Read the article

  • Circular Dependency of Navigation Control in iPhone

    - by Taimur Hamza
    Hi everyone , In my view this is one of the strangest problem i have ever come across in iPhone app development. Let me explain the scenario , i have main screen 'A' on which i have a Button that directs me to another Screen say 'B'. Now on Screen 'B' i have a feature in which user can send a mail to his friend for promotion purpose e.g a user wishes to tell a frnd about this app so i used MFMailComposeViewController and a view is generated where the user types the address and click send ( subject and body of mail is automatically generated ). After sending the mail a new view opens say screen 'C' and here i want to give the user the options . 1. Go to Screen 'A' ( which is main screen of the app ) 2. Go back to Screen 'B' ( from where the user requested to send a mail to his frnd ). Now the strange part i cannot declare the variables ( Screen 'A' and 'B' ) of both these files here at in header file of screen 'C' . Even when i declare the header file at the top it generates an error. The variables can be easily be declared and used for other screens but not for these 2 screens. Can anybody please explain wats the problem.? this the text of the error "/Users/admin/Documents/AppName/Classes/A.h:42: error: expected specifier-qualifier-list before 'B'" Thanks Guys ! Taimur

    Read the article

  • how do I paste text to a line by line text filter like awk, without having stdin echo to the screen?

    - by Barton Chittenden
    I have a text in an email on a windows box that looks something like this: 100 some random text 101 some more random text 102 lots of random text, all different 103 lots of random text, all the same I want to extract the numbers, i.e. the first word on each line. I've got a terminal running bash open on my Linux box... If these were in a text file, I would do this: awk '{print $1}' mytextfile.txt I would like to paste these in, and get my numbers out, without creating a temp file. my naive first attempt looked like this: $ awk '{print $1}' 100 some random text 100 101 some more random text 101 102 lots of random text, all different 103 lots of random text, all the same 102 103 The buffering of stdin and stdout make a hash of this. I wouldn't mind if stdin all printed first, followed by all of stdout; this is what would happen if I were to paste into 'sort' for example, but awk and sed are a different story. a little more thought gave me this: open two terminals. Create a fifo file. Read from the fifo on one terminal, write to it on another. This does in fact work, but I'm lazy. I don't want to open a second terminal. Is there a way in the shell that I can hide the text echoed to the screen when I'm passing it in to a pipe, so that I paste this: 100 some random text 101 some more random text 102 lots of random text, all different 103 lots of random text, all the same but see this? $ awk '{print $1}' 100 101 102 103

    Read the article

  • Log off from Remote Desktop Session does not closing Session, showing the login screen again on Wind

    - by Santhosha
    Hi As per requirement we have written one custom GINA. I have observed one interesting behavior in Windows XP 32 Bit(SP2). Customized GINA internally calls windows default Windows GINA(msgina.dll) and shows one extra window as per our requirement. I used to do remote desktop to XP machine from my machine. After replacing Windows GINA with customized GINA I tried to log off from the XP Machine(I am Using Remote Desktop Connection to log in), Log off completes successfully(After showing saving your settings, Closing network connections etc) and I will get log in screen which we get during log on, this is not expected comapred to other flavors of Windows OD. Where as in other operating systems such as Windows XP 64 Bit/ Windows 2003 32/64 Bit even after replacing the Windows Gina with custom GINA remote desktop session closes after log off from the machine. I have tried installing Novell GINA on Windows XP 32 Bit but i have not find any issue with that. I have Tried upgrading XP SP2 to SP3, still i am facing the same issue. Whether anyone faced Such issues when worked with Windows GINA? Thanks in advance Santhosha K S

    Read the article

  • How do I [legally] get the current first responder on the screen on an iPhone?

    - by Anthony D
    I submitted my app a little over a week ago and got the dreaded rejection email today. It reads as follows: Dear -----------, Thank you for submitting --------- to the App Store. Unfortunately it cannot be added to the App Store because it is using a private API. Use of non-public APIs, which as outlined in the iPhone Developer Program License Agreement section 3.3.1 is prohibited: "3.3.1 Applications may only use Documented APIs in the manner prescribed by Apple and must not use or call any private APIs." The non-public API that is included in your application is firstResponder. Regards, iPhone Developer Program Now, the offending API call is actually a solution I found here on SO: UIWindow *keyWindow = [[UIApplication sharedApplication] keyWindow]; UIView *firstResponder = [keyWindow performSelector:@selector(firstResponder)]; So this is my question; How do I get the current first responder on the screen? I'm looking for a legal way that won't get my app rejected. Thanks. I figured this out based on the solution provided by Thomas below. Here is what the final code looks like: @implementation UIView (FindFirstResponder) - (UIView *)findFirstResonder { if (self.isFirstResponder) { return self; } for (UIView *subView in self.subviews) { UIView *firstResponder = [subView findFirstResonder]; if (firstResponder != nil) { return firstResponder; } } return nil; } @end

    Read the article

  • Sending an email with browser capabilities and screen size etc.

    - by talkingnews
    A lot of my visitors are blind (with it being a site for the blind), and often when trying to diagnose problems, I'd like to know what version of browser etc they're using, whether flash is installed. Because more often than not, someone will swear they are using X, when in fact Y is installed. Currently, I'm using http://jsbrwsniff.sourceforge.net/usage.html piped into an email, but I've got 2 problems here: First of all, jsbrwsniff is quite "heavy" and hasn't been updated since early 2007, so there's a lot of -1's in the result. Secondly, if I call it as follows, the page reloads: <a href="#" onclick="sendEmail()">Email feedback</a> And if I call it like this, the page goes blank and looks like it's trying to infinitely load a blank page: <a href="javascript:sendEmail()">Email feedback</a> See the nightmare for yourself here: http://kingston.talking-newspapers.co.uk/ Now, I know there are 1001 articles and comments here and elsewhere saying "don't use browser sniffers, they can be spoofed (etc)", but honestly, you'll have to trust me that this is a significantly useful tool when you're talking someone in their more "senior years" and using a screenreader through "help about", when they've clicked the wrong window to start with! I'm using jquery anyway in the site, and I'm aware of $jQuery.browser and $jQuery.support, but these don't tell me the elements I need (like whether Flash is installed, and what version etc). I've looked everywhere for a jquery plugin for my needs, with no luck. Finally, if I have to stick to the current method of jsbrwsniff then it's not the end of the world, but if anyone knows a way of launching the user's email client populated with the information I need but WITHOUT refreshing or blanking the page, I'd love to know. BTW - there's a good reason for not using a webform, which is simply because it's easier for the screen-reader user to use an email client they are used to. Thanks!

    Read the article

  • How to display a Dialog on window created using XCreateWindow in QT 4.5.2

    - by Ummar
    I am doing work on project. In which I have developed a full size screen displaying images using XCreateWindow. Now I want to display a dialog on this screen. I have created a QDialog it does'nt show on the full size screen but it is displayed on screen when it is not full size. Any Help. My code for creating screen and dialogbox is as follows XSetWindowAttributes attribs; XClassHint *classhints; XSizeHints *sizehints; int wndwidth, wndheight; long input_mask, ic_input_mask; XEvent xevent; wndwidth = fullscreen ? WidthOfScreen(screen) : width; wndheight = fullscreen ? HeightOfScreen(screen) : height; attribs.background_pixel = BlackPixelOfScreen(screen); attribs.backing_store = ownbackstore ? NotUseful : Always; attribs.override_redirect = fullscreen; wnd = XCreateWindow(display, RootWindowOfScreen(screen), 0, 0, wndwidth, wndheight, 0, CopyFromParent, InputOutput, CopyFromParent, CWBackPixel | CWBackingStore | CWOverrideRedirect, &attribs); XRaiseWindow(display, wnd); //QDialog I want to show on wnd(XCreateWindow) ToolbarDialog *objToolbarDialog= new ToolbarDialog(); objToolbarDialog->setVisible(true); objToolbarDialog->showNormal();

    Read the article

  • Android: How do I make a video splash screen repeat until webview finishes loading the url?

    - by Nikoli4
    I would like to make a small video (about 4 seconds) repeat until webview finishes loading the desired URL in the background. Right now the video plays once, then a blank black screen comes up until the page loads. I'm still pretty new to this... Thanks in advance for any help! Sorry for the EDITED stuff, but it was necessary. Here is my splash java import android.app.Activity; import android.content.Intent; import android.media.MediaPlayer; import android.media.MediaPlayer.OnCompletionListener; import android.os.Bundle; import android.widget.VideoView; public class Splash extends Activity implements OnCompletionListener { @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.splash); VideoView video = (VideoView) findViewById(R.id.videoView); video.setVideoPath("android.resource://com.EDITED/raw/" + R.raw.splash); video.start(); video.setOnCompletionListener(this); } @Override public void onCompletion(MediaPlayer mp) { Intent intent = new Intent(this, EDITEDWebActivity.class); startActivity(intent); finish(); } }

    Read the article

  • How to get JTree expanded?

    - by Dzmitry Zhaleznichenka
    I have a wizard with several screens where user has to fill his/her details for further processing. At the second screen I have a radio group with three radio buttons that enable additional elements. To proceed, user has to choose one of them. When user selects third button, single-selection JTree filled in with data enables and user has to select an option from it. Then user has to press "Next" to get to next screen. The option he\she had selected is stored as a TreePath. So far so good. My problem is the following. If the user wants to come back from the following screen to the screen with a JTree, I want to provide him\her with the JTree expanded to the option that had been selected and to highlight the option. However, whatsoever I try to do for that (any combinations of expandPath, scrollPathToVisible, addSelectionPath, makeVisible) always provides me with a collapsed tree. I try to expand both leaves and nodes. My code looks like this: rbProcessJTree.setSelected(isProcessJTree()); if (null != getSelectedTablePath()){ trTables.addSelectionPath(getSelectedTablePath()); trTables.expandPath(getSelectedTablePath()); trTables.scrollPathToVisible(getSelectedTablePath()); } When setSelected() is called, state change listener is invoked that enables JTree. The model is loaded during the form initialization. Each time I switch between screens, I save the input data from previous screen and dispose it. Then, when I need to open previous screen back, I save data from the following screen, dispose it, load data to this screen and show it. So each time the screen is generating from scratch. Could you please explain, what sequence of operations has to be done to get JTree expanded in a newly created form,with data model loaded and selection path provided?

    Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >